Internal Combustion Engines

Size: px
Start display at page:

Download "Internal Combustion Engines"

Transcription

1 Air and Fuel Induction Lecture 3 1

2 Outline In this lecture we will discuss the following: A/F mixture preparation in gasoline engines using carburetion. Air Charging technologies: Superchargers Turbochargers 2

3 As discussed in the previous lecture, there are two main methods for A/F mixture preparation in gasoline engines: Fuel injection Carburetion Until the 1980s, carburetion used to be the universal technology adopted by all car manufacturers. Despite the many shortcomings of carburettors, they are relatively simple and inexpensive. 3

4 4

5 A carburettor system basically consists of: Venturi tube Throttle plate Fuel capillary tube Fuel reservoir Choke 5

6 Air enters the carburettor at nearly atmospheric pressure, and flows in the direction of the lower pressure in the engine cylinders. Due to the losses the flow encounters as it moves through the system, a pressure differential is created across the fuel capillary tube. This forces the fuel in the capillary tube to flow into the venturi throat in the form of droplets that evaporate and mix with the air in the intake manifold. 6

7 The purpose of the venturi tube is to: increase the pressure drop and hence the pressure differential. increase the velocity of the air. Note that the pressure drop in the venturi tube depends on the velocity of the flow: P V 2 As a result, as the air flow rate increases, the pressure differential increases. This increases the fuel flow and thus the A/F ratio can (roughly) be maintained at the desired level. 7

8 8

9 It must be noted that there are two factors that act against each other with regard to the sizing of the venturi. Increasing the diameter will decrease the pressure drop and thus decreases the fuel flow and the fuel control. This however, will increase the volumetric efficiency, and vice-versa. One way to overcome this dilemma, is by using a primary and a secondary venturi. 9

10 The secondary venturi is used to give good control of the fuel while the larger one ensures minimum losses regarding the volumetric efficiency. 10

11 The speed of the engine (power demand) is controlled by the throttle which determines the air flow rate. At high speed or acceleration operation, the throttle is wide-open (WOT) which is also characterised by a rich mixture. At steady state cruising conditions, the engine operates near stoichiometry or slightly lean conditions. At idle conditions, the throttle is nearly closed, and thus minimising the flow rate through the venturi. This leads to only a minimal pressure drop and very low fuel flow rate and consequently to poor fuel flow control. To avoid the possible resulting misfires, an idle valve is added downstream of the venturi with the aim of increasing the fuel concentration. 11

12 The choke is used to overcome the cold start difficulties. When the choke valve is closed, it restricts the air flow and creates a vacuum in the entire intake system. This results in a large pressure differential across the fuel capillary tube and the idle valve, which leads to a large fuel flow. This gives a very rich mixture (very low A/F ratios). 12

13 But why does this need to be done at cold conditions? Cold fuel: Higher viscosity, slower flow, larger droplets Cold engine parts This leads to much less effective vaporisation of the fuel even if the fuel liquid flow is sufficient. This is made even worse with the fact that the flow is very low since the engine starts at a low speed. 13

14 The disadvantages of a carburettor system can be summarised as follows: Bad fuel economy Slow and difficult control of the fuel flow and mixture strength Large pumping losses Difficulty in ensuring homogeneity of the mixture Icing at the throttle due to evaporative and expansion cooling 14

15 Charging Systems The idea behind charging is increasing the amount of the mixture entering the cylinder through increasing the pressure of the intake charge. This results in an increased power output. Charging can be done either through superchargers or turbochargers. This is applied now to all two-stroke engines, most C.I. engines and many S.I. engines. 15

16 Superchargers Vs Turbochargers Superchargers are driven directly off the crankshaft. Additional parasitic load on the engine. Higher cost and noise. Much quicker response. Turbochargers are driven by a turbine utilising the exhaust gases. No parasitic loads. Suffers from turbolag which occurs during sudden throttle change. 16

17 Turbochargers Many modern turbochargers are variable geometry turbochargers. The turbine blade angles change according to the flow rate to give maximum efficiency. 17

18 Charge inter-cooling It must be noted that charging not only increases the intake pressure, but also the intake temperature. This is undesirable in S.I. engines, since it leads to decreasing the ignition delay and thus to knocking. In C.I. engines, this can lead to increased NOx emissions. As a result, most superchargers/turbochargers are equipped with an intercooler to decrease the charge temperature. 18

19 Charge inter-cooling 19

20 Supercharger Efficiency The isentropic efficiency of a supercharger can be given as follows: η sc = w isen /w act η sc = (T 2s -T 1 )/(T 2a -T 1 ) Where, w isen : Isentropic work w act : actual work T : Temperature T 2s / T 1 = (P 2 /P 1 ) (γ-1)/γ 20

21 Turbocharger Efficiency η turbo = η s turb η s comp η m Where, η s comp = (T 2s -T 1 )/(T 2a -T 1 ) η s turb = (T 1 -T 2a )/(T 1 -T 2s ) η m = w ca / w t a Typical values are in the range of 80-90% 21

2) Rich mixture: A mixture which contains less air than the stoichiometric requirement is called a rich mixture (ex. A/F ratio: 12:1, 10:1 etc.

2) Rich mixture: A mixture which contains less air than the stoichiometric requirement is called a rich mixture (ex. A/F ratio: 12:1, 10:1 etc. Unit 3. Carburettor University Questions: 1. Describe with suitable sketches : Main metering system and Idling system 2. Draw the neat sketch of a simple carburettor and explain its working. What are the

More information

GASOLINE DIRECT INJECTION IN SI ENGINES B. PAVAN VISWANADH P. ASHOK KUMAR. Mobile No : Mobile No:

GASOLINE DIRECT INJECTION IN SI ENGINES B. PAVAN VISWANADH P. ASHOK KUMAR. Mobile No : Mobile No: GASOLINE DIRECT INJECTION IN SI ENGINES SUBMIT TED BY B. PAVAN VISWANADH P. ASHOK KUMAR Y06ME011, III/IV B. Tech Y06ME003, III/IV B. Tech Pavan.visu@gmail.com ashok.me003@gmail.com Mobile No :9291323516

More information

Chapter 4 ANALYTICAL WORK: COMBUSTION MODELING

Chapter 4 ANALYTICAL WORK: COMBUSTION MODELING a 4.3.4 Effect of various parameters on combustion in IC engines: Compression ratio: A higher compression ratio increases the pressure and temperature of the working mixture which reduce the initial preparation

More information

Chapter 6. Supercharging

Chapter 6. Supercharging SHROFF S. R. ROTARY INSTITUTE OF CHEMICAL TECHNOLOGY (SRICT) DEPARTMENT OF MECHANICAL ENGINEERING. Chapter 6. Supercharging Subject: Internal Combustion Engine 1 Outline Chapter 6. Supercharging 6.1 Need

More information

Module 5: Emission Control for SI Engines Lecture20:ADD-ON SYSTEMS FOR CONTROL OF ENGINE-OUT EMISSIONS

Module 5: Emission Control for SI Engines Lecture20:ADD-ON SYSTEMS FOR CONTROL OF ENGINE-OUT EMISSIONS ADD-ON SYSTEMS FOR CONTROL OF ENGINE-OUT EMISSIONS The Lecture Contains: Crankcase Emission Control (PCV System) Evaporative Emission Control Exhaust Gas Recirculation Water Injection file:///c /...%20and%20Settings/iitkrana1/My%20Documents/Google%20Talk%20Received%20Files/engine_combustion/lecture20/20_1.htm[6/15/2012

More information

1 In all circumstances, it can be easily ignited by the spark. 2 The maximum possible amount of chemical energy can be

1 In all circumstances, it can be easily ignited by the spark. 2 The maximum possible amount of chemical energy can be SIE: Requirements for Metering & Mixing ICE Fuel Metering Dr. Md. Zahurul Haq Professor Department of Mechanical Engineering Bangladesh University of Engineering & Technology (BUET) Dhaka-1000, Bangladesh

More information

Module 2:Genesis and Mechanism of Formation of Engine Emissions Lecture 9:Mechanisms of HC Formation in SI Engines... contd.

Module 2:Genesis and Mechanism of Formation of Engine Emissions Lecture 9:Mechanisms of HC Formation in SI Engines... contd. Mechanisms of HC Formation in SI Engines... contd. The Lecture Contains: HC from Lubricating Oil Film Combustion Chamber Deposits HC Mixture Quality and In-Cylinder Liquid Fuel HC from Misfired Combustion

More information

Module 3: Influence of Engine Design and Operating Parameters on Emissions Lecture 14:Effect of SI Engine Design and Operating Variables on Emissions

Module 3: Influence of Engine Design and Operating Parameters on Emissions Lecture 14:Effect of SI Engine Design and Operating Variables on Emissions Module 3: Influence of Engine Design and Operating Parameters on Emissions Effect of SI Engine Design and Operating Variables on Emissions The Lecture Contains: SI Engine Variables and Emissions Compression

More information

Module7:Advanced Combustion Systems and Alternative Powerplants Lecture 32:Stratified Charge Engines

Module7:Advanced Combustion Systems and Alternative Powerplants Lecture 32:Stratified Charge Engines ADVANCED COMBUSTION SYSTEMS AND ALTERNATIVE POWERPLANTS The Lecture Contains: DIRECT INJECTION STRATIFIED CHARGE (DISC) ENGINES Historical Overview Potential Advantages of DISC Engines DISC Engine Combustion

More information

AT AUTOMOTIVE ENGINES QUESTION BANK

AT AUTOMOTIVE ENGINES QUESTION BANK AT6301 - AUTOMOTIVE ENGINES QUESTION BANK UNIT I: CONSTRUCTION & WORKING PRINCIPLE OF IC ENGINES 1. State the application of CI engines? 2. What is Cubic capacity of an engine? 3. What is the purpose of

More information

Dr Ali Jawarneh Department of Mechanical Engineering

Dr Ali Jawarneh Department of Mechanical Engineering Chapter 7: Combustion Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Outline In this lecture we will discuss the combustion process: The characteristics of the process. The different

More information

Basic Requirements. ICE Fuel Metering. Mixture Quality Requirements. Requirements for Metering & Mixing

Basic Requirements. ICE Fuel Metering. Mixture Quality Requirements. Requirements for Metering & Mixing Basic Requirements ICE Fuel Metering Dr. M. Zahurul Haq Professor Department of Mechanical Engineering Bangladesh University of Engineering & Technology (BUET) Dhaka-1000, Bangladesh zahurul@me.buet.ac.bd

More information

VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE

VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE Page 1 of 13 EFFECT OF VALVE TIMING DIAGRAM ON VOLUMETRIC EFFICIENCY: Qu. 1:Why Inlet valve is closed after the Bottom Dead Centre

More information

Which are the four important control loops of an spark ignition (SI) engine?

Which are the four important control loops of an spark ignition (SI) engine? 151-0567-00 Engine Systems (HS 2017) Exercise 1 Topic: Lecture 1 Johannes Ritzmann (jritzman@ethz.ch), Raffi Hedinger (hraffael@ethz.ch); October 13, 2017 Problem 1 (Control Systems) Why do we use control

More information

Internal Combustion Engines

Internal Combustion Engines Introduction Lecture 1 1 Outline In this lecture we will learn about: Definition of internal combustion Development of the internal combustion engine Different engine classifications We will also draw

More information

Homogeneous Charge Compression Ignition (HCCI) Engines

Homogeneous Charge Compression Ignition (HCCI) Engines Homogeneous Charge Compression Ignition (HCCI) Engines Aravind. I. Garagad. Shri Dharmasthala Manjunatheshwara College of Engineering and Technology, Dharwad, Karnataka, India. ABSTRACT Large reductions

More information

Induction, Cooling, & Exhaust Aviation Maintenance Technology

Induction, Cooling, & Exhaust Aviation Maintenance Technology Induction, Cooling, & Exhaust Aviation Maintenance Technology INDUCTION Induction = There are two basic types 1. 2. Non-supercharged components 1. 2. 3. 4. 5. 6. 7. 8. Air Scoop Air filters. Ducting Hot

More information

Heat Transfer in Engines. Internal Combustion Engines

Heat Transfer in Engines. Internal Combustion Engines Heat Transfer in Engines Internal Combustion Engines Energy Distribution Removing heat is critical in keeping an engine and lubricant from thermal failure Amount of energy available for use: Brake thermal

More information

LECTURE NOTES INTERNAL COMBUSTION ENGINES SI AN INTEGRATED EVALUATION

LECTURE NOTES INTERNAL COMBUSTION ENGINES SI AN INTEGRATED EVALUATION LECTURE NOTES on INTERNAL COMBUSTION ENGINES SI AN INTEGRATED EVALUATION Integrated Master Course on Mechanical Engineering Mechanical Engineering Department November 2015 Approach SI _ indirect injection

More information

Engine Cycles. T Alrayyes

Engine Cycles. T Alrayyes Engine Cycles T Alrayyes Introduction The cycle experienced in the cylinder of an internal combustion engine is very complex. The cycle in SI and diesel engine were discussed in detail in the previous

More information

ADDIS ABABA UNIVERSITY INSTITUTE OF TECHNOLOGY

ADDIS ABABA UNIVERSITY INSTITUTE OF TECHNOLOGY 1 INTERNAL COMBUSTION ENGINES ADDIS ABABA UNIVERSITY INSTITUTE OF TECHNOLOGY MECHANICAL ENGINEERING DEPARTMENT DIVISON OF THERMAL AND ENERGY CONVERSION IC Engine Fundamentals 2 Engine Systems An engine

More information

Focus on Training Section: Unit 2

Focus on Training Section: Unit 2 All Pump Types Page 1 1. Title Page Learning objectives Become familiar with the 4 stroke cycle Become familiar with diesel combustion process To understand how timing affects emissions To understand the

More information

Combustion. T Alrayyes

Combustion. T Alrayyes Combustion T Alrayyes Fluid motion with combustion chamber Turbulence Swirl SQUISH AND TUMBLE Combustion in SI Engines Introduction The combustion in SI engines inside the engine can be divided into three

More information

8.21 The Physics of Energy Fall 2009

8.21 The Physics of Energy Fall 2009 MIT OpenCourseWare http://ocw.mit.edu 8.21 The Physics of Energy Fall 2009 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. 8.21 Lecture 11 Internal Combustion

More information

Diagnostic Trouble Codes (continued) SAE Defined Codes

Diagnostic Trouble Codes (continued) SAE Defined Codes 78 SAE Defined Codes P01XX Fuel and Air Metering P0100 Mass or Volume Airflow Circuit Problem P0101 Mass or Volume Airflow Circuit Range or Performance Problem P0102 Mass or Volume Airflow Circuit Low

More information

UNIT IV INTERNAL COMBUSTION ENGINES

UNIT IV INTERNAL COMBUSTION ENGINES UNIT IV INTERNAL COMBUSTION ENGINES Objectives After the completion of this chapter, Students 1. To know the different parts of IC engines and their functions. 2. To understand the working principle of

More information

Internal Combustion Engines

Internal Combustion Engines Emissions & Air Pollution Lecture 3 1 Outline In this lecture we will discuss emission control strategies: Fuel modifications Engine technology Exhaust gas aftertreatment We will become particularly familiar

More information

Powertrain Efficiency Technologies. Turbochargers

Powertrain Efficiency Technologies. Turbochargers Powertrain Efficiency Technologies Turbochargers Turbochargers increasingly are being used by automakers to make it possible to use downsized gasoline engines that consume less fuel but still deliver the

More information

Internal Combustion Engines

Internal Combustion Engines Engine Cycles Lecture Outline In this lecture we will: Analyse actual air fuel engine cycle: -Stroke cycle -Stroke cycle Compare these cycles to air standard cycles Actual Engine Cycle Although air standard

More information

Assignment-1 Air Standard Cycles

Assignment-1 Air Standard Cycles Assignment-1 Air Standard Cycles 1. What do u mean by air standard cycle? List assumptions for air standard cycle & give reasons why air standard cycle differs from actual cycle. 2. Derive an equation

More information

A. Aluminum alloy Aluminum that has other metals mixed with it.

A. Aluminum alloy Aluminum that has other metals mixed with it. ENGINE REPAIR UNIT 1: ENGINE DESIGN LESSON 1: PRINCIPLES OF ENGINE DESIGN I. Terms and definitions A. Aluminum alloy Aluminum that has other metals mixed with it. B. Bearing A device that allows movement

More information

Simple Carburettor Fuel System for a Piston Engine. And how it works

Simple Carburettor Fuel System for a Piston Engine. And how it works Simple Carburettor Fuel System for a Piston Engine And how it works Inlet Exhaust Tank PISTON ENGINE Carburettor Fuel System Filler Cap COCKPIT FUEL GAUGE E FUEL 1/2 F Filler Neck Tank Cavity FUEL LEVEL

More information

ENGINE & WORKING PRINCIPLES

ENGINE & WORKING PRINCIPLES ENGINE & WORKING PRINCIPLES A heat engine is a machine, which converts heat energy into mechanical energy. The combustion of fuel such as coal, petrol, diesel generates heat. This heat is supplied to a

More information

I.C Engine Topic: Fuel supply systems Part-1

I.C Engine Topic: Fuel supply systems Part-1 I.C Engine Topic: Fuel supply systems Part-1 By: Prof.Kunalsinh Kathia Essential parts of carburetor Fuel strainer Float chamber Metering and idiling system Choke and throttle Fuel strainer As gasoline

More information

Internal combustion engines can be classified in a number of different ways: 1. Types of Ignition

Internal combustion engines can be classified in a number of different ways: 1. Types of Ignition Chapter 1 Introduction 1-3 ENGINE CLASSIFICATIONS Internal combustion engines can be classified in a number of different ways: 1. Types of Ignition 1 (a) Spark Ignition (SI). An SI engine starts the combustion

More information

Internal Combustion Engines

Internal Combustion Engines Internal Combustion Engines The internal combustion engine is an engine in which the burning of a fuel occurs in a confined space called a combustion chamber. This exothermic reaction of a fuel with an

More information

State of the Art (SOTA) Manual for Internal Combustion Engines

State of the Art (SOTA) Manual for Internal Combustion Engines State of the Art (SOTA) Manual for Internal Combustion Engines July 1997 State of New Jersey Department of Environmental Protection Air Quality Permitting Program State of the Art (SOTA) Manual for Internal

More information

Chapter 8 Production of Power from Heat

Chapter 8 Production of Power from Heat Chapter 8 Production of Power from Heat Different sources of power, such as solar energy (from sun), kinetic energy from atmospheric winds and potential energy from tides. The most important source of

More information

4. With a neat sketch explain in detail about the different types of fuel injection system used in SI engines. (May 2016)

4. With a neat sketch explain in detail about the different types of fuel injection system used in SI engines. (May 2016) SYED AMMAL ENGINEERING COLLEGE (Approved by the AICTE, New Delhi, Govt. of Tamilnadu and Affiliated to Anna University, Chennai) Established in 1998 - An ISO 9001:2000 Certified Institution Dr. E.M.Abdullah

More information

REVIEW ON GASOLINE DIRECT INJECTION

REVIEW ON GASOLINE DIRECT INJECTION International Journal of Aerospace and Mechanical Engineering REVIEW ON GASOLINE DIRECT INJECTION Jayant Kathuria B.Tech Automotive Design Engineering jkathuria97@gmail.com ABSTRACT Gasoline direct-injection

More information

UNDERSTANDING 5 GAS DIAGNOSIS

UNDERSTANDING 5 GAS DIAGNOSIS UNDERSTANDING 5 GAS DIAGNOSIS AND EMISSIONS Gas Diagnostic Steps This procedure will help in your efforts to figure out what the five-gas reading are telling you. In order for five gas analyses to be conclusive

More information

E - THEORY/OPERATION - TURBO

E - THEORY/OPERATION - TURBO E - THEORY/OPERATION - TURBO 1995 Volvo 850 1995 ENGINE PERFORMANCE Volvo - Theory & Operation 850 - Turbo INTRODUCTION This article covers basic description and operation of engine performance-related

More information

SET - 1 II B. Tech II Semester Regular/Supplementary Examinations, April/May-2017 THERMAL ENGINEERING-I (Mechanical Engineering) Time: 3 hours Max. Marks: 70 Note: 1. Question Paper consists of two parts

More information

Principles of Engine Operation. Information

Principles of Engine Operation. Information Internal Combustion Engines MAK 4070E Principles of Engine Operation Prof.Dr. Cem Soruşbay Istanbul Technical University Information Prof.Dr. Cem Soruşbay İ.T.Ü. Makina Fakültesi Motorlar ve Taşıtlar Laboratuvarı

More information

Module 2:Genesis and Mechanism of Formation of Engine Emissions Lecture 3: Introduction to Pollutant Formation POLLUTANT FORMATION

Module 2:Genesis and Mechanism of Formation of Engine Emissions Lecture 3: Introduction to Pollutant Formation POLLUTANT FORMATION Module 2:Genesis and Mechanism of Formation of Engine Emissions POLLUTANT FORMATION The Lecture Contains: Engine Emissions Typical Exhaust Emission Concentrations Emission Formation in SI Engines Emission

More information

ACTUAL CYCLE. Actual engine cycle

ACTUAL CYCLE. Actual engine cycle 1 ACTUAL CYCLE Actual engine cycle Introduction 2 Ideal Gas Cycle (Air Standard Cycle) Idealized processes Idealize working Fluid Fuel-Air Cycle Idealized Processes Accurate Working Fluid Model Actual

More information

Introduction. Internal Combustion Engines

Introduction. Internal Combustion Engines Introduction Internal Combustion Engines Internal Combustion Engines A heat engine that converts chemical energy in a fuel into mechanical energy. Chemical energy first converted into thermal energy (Combustion)

More information

Problem 1 (ECU Priority)

Problem 1 (ECU Priority) 151-0567-00 Engine Systems (HS 2016) Exercise 6 Topic: Optional Exercises Raffi Hedinger (hraffael@ethz.ch), Norbert Zsiga (nzsiga@ethz.ch); November 28, 2016 Problem 1 (ECU Priority) Use the information

More information

Induction, Cooling, & Exhaust. Aviation Maintenance Technology 111 B B

Induction, Cooling, & Exhaust. Aviation Maintenance Technology 111 B B Induction, Cooling, & Exhaust Aviation Maintenance Technology 111 B - 112 B Unliscensed copyrighted material - W. North 1998 Unliscensed copyrighted material - W. North 1998 Induction = those locations

More information

EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4DOTC

EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4DOTC EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4DOTC SYSTEM OVERVIEW 1. System Overview There are three emission control systems, which are as follows: Crankcase emission control system Exhaust emission

More information

Lecture 5. Abnormal Combustion

Lecture 5. Abnormal Combustion Lecture 5 Abnormal Combustion Abnormal Combustion The Abnormal Combustion:- When the combustion gets deviated from the normal behavior resulting loss of performance or damage to the engine. It is happened

More information

SAMPLE STUDY MATERIAL

SAMPLE STUDY MATERIAL IC Engine - ME GATE, IES, PSU 1 SAMPLE STUDY MATERIAL Mechanical Engineering ME Postal Correspondence Course Internal Combustion Engine GATE, IES & PSUs IC Engine - ME GATE, IES, PSU 2 C O N T E N T 1.

More information

AN EXPLANATION OF CIRCUITS CARTER YH HORIZONTAL CLIMATIC CONTROL CARBURETER

AN EXPLANATION OF CIRCUITS CARTER YH HORIZONTAL CLIMATIC CONTROL CARBURETER AN EXPLANATION OF CIRCUITS CARTER YH HORIZONTAL CLIMATIC CONTROL CARBURETER The Carter Model YH carbureter may be compared with a Carter YF downdraft carbureter with the circuits rearranged to operate

More information

Accident Prevention Program

Accident Prevention Program Accident Prevention Program Part I ENGINE OPERATION FOR PILOTS by Teledyne Continental Motors SAFE ENGINE OPERATION INCLUDES: Proper Pre-Flight Use the correct amount and grade of aviation gasoline. Never

More information

THE CARBURETOR: THE ADDITIONAL SYSTEMS

THE CARBURETOR: THE ADDITIONAL SYSTEMS THE CARBURETOR: THE ADDITIONAL SYSTEMS From the acceleration pump to the power jet: the special configuration of circuits that apply to some carburetor models As stated in the previous article, a carburetor

More information

Highly transient gas engine operation from a turbocharging perspective

Highly transient gas engine operation from a turbocharging perspective HERVÉ MARTIN, ABB TURBO SYSTEMS LTD Highly transient gas engine operation from a turbocharging perspective 10th CIMAC CASCADES, Kobe, 12 th October 2018 Overview Introduction Basics of load pick-up Modeling

More information

density ratio of 1.5.

density ratio of 1.5. Problem 1: An 8cyl 426 ci Hemi motor makes 426 HP at 5500 rpm on a compression ratio of 10.5:1. It is over square by 10% meaning that it s stroke is 10% less than it s bore. It s volumetric efficiency

More information

Week 10. Gas Power Cycles. ME 300 Thermodynamics II 1

Week 10. Gas Power Cycles. ME 300 Thermodynamics II 1 Week 10 Gas Power Cycles ME 300 Thermodynamics II 1 Today s Outline Gas power cycles Internal combustion engines Four-stroke cycle Thermodynamic cycles Ideal cycle ME 300 Thermodynamics II 2 Gas Power

More information

Internal Combustion Engines

Internal Combustion Engines Friction & Lubrication Lecture 1 1 Outline In this lecture we will discuss the following: Engine friction losses. Piston arrangement losses. Measurement of friction losses. Engine lubrication systems.

More information

5. FUEL SYSTEM 5-0 FUEL SYSTEM MXU 250R/300R

5. FUEL SYSTEM 5-0 FUEL SYSTEM MXU 250R/300R 5 FUEL SYSTEM 5 SERVICE INFORMATION------------------------------------------------ 5-2 TROUBLESHOOTING----------------------------------------------------- 5-3 FUEL TANK -----------------------------------------------------------------

More information

MIXTURE FORMATION IN SPARK IGNITION ENGINES. Chapter 5

MIXTURE FORMATION IN SPARK IGNITION ENGINES. Chapter 5 MIXTURE FORMATION IN SPARK IGNITION ENGINES Chapter 5 Mixture formation in SI engine Engine induction and fuel system must prepare a fuel-air mixture that satisfiesthe requirements of the engine over its

More information

ROYAL CANADIAN AIR CADETS PROFICIENCY LEVEL FOUR INSTRUCTIONAL GUIDE SECTION 1 EO M DESCRIBE FUEL SYSTEMS PREPARATION

ROYAL CANADIAN AIR CADETS PROFICIENCY LEVEL FOUR INSTRUCTIONAL GUIDE SECTION 1 EO M DESCRIBE FUEL SYSTEMS PREPARATION ROYAL CANADIAN AIR CADETS PROFICIENCY LEVEL FOUR INSTRUCTIONAL GUIDE SECTION 1 EO M432.01 DESCRIBE FUEL SYSTEMS Total Time: 30 min PREPARATION PRE-LESSON INSTRUCTIONS Resources needed for the delivery

More information

OBJECTIVE: GENERAL ASPECTS ABOUT ENGINES MECHANISM:

OBJECTIVE: GENERAL ASPECTS ABOUT ENGINES MECHANISM: LANDMARK UNIVERSITY, OMU-ARAN LECTURE NOTE 3 COLLEGE: COLLEGE OF SCIENCE AND ENGINEERING DEPARTMENT: MECHANICAL ENGINEERING Course code: MCE 211 Course title: Introduction to Mechanical Engineering Credit

More information

Introduction Engine Systems. Chris Onder, Raffael Hedinger, Norbert Zsiga, Michael Zihlmann

Introduction Engine Systems. Chris Onder, Raffael Hedinger, Norbert Zsiga, Michael Zihlmann Introduction Engine Systems Chris Onder, Raffael Hedinger, Norbert Zsiga, Michael Zihlmann 1 Introduction Engine Systems 1. Concept of a combustion engine 2. Different types of engines 3. Topics of the

More information

Fuel control. The fuel injection system tasks. Starting fuel pump (FP)

Fuel control. The fuel injection system tasks. Starting fuel pump (FP) 1 Fuel control The fuel injection system tasks - To provide fuel - To distribute the fuel between the cylinders - To provide the correct quantity of fuel Starting fuel pump (FP) The control module (1)

More information

Smt. S. R. PATEL ENGINEERING COLLEGE Dabhi, unjha pin

Smt. S. R. PATEL ENGINEERING COLLEGE Dabhi, unjha pin EXPERIMENTS IN INTERNAL COMBUCTION ENGINE Smt. S. R. PATEL ENGINEERING COLLEGE Dabhi, unjha pin- 384 170 Department of MECHANICAL engineering Subject :INTERNAL COMBUCTION ENGINE Subject code: 161902 INDEX

More information

Vacuum Readings for Tuning and Diagnosis

Vacuum Readings for Tuning and Diagnosis Vacuum Readings for Tuning and Diagnosis -Henry P. Olsen Once you learn to properly interpret its readings, a vacuum gauge can be one of the most useful tools in your toolbox. 22 FEATURE Some people consider

More information

Sensors & Controls. Everything you wanted to know about gas engine ignition technology but were too afraid to ask.

Sensors & Controls. Everything you wanted to know about gas engine ignition technology but were too afraid to ask. Everything you wanted to know about gas engine ignition technology but were too afraid to ask. Contents 1. Introducing Electronic Ignition 2. Inductive Ignition 3. Capacitor Discharge Ignition 4. CDI vs

More information

Did you know? If you follow the maintenance guidelines for your vehicle, your turbo will last longer.

Did you know? If you follow the maintenance guidelines for your vehicle, your turbo will last longer. Did you know? You should take your time when starting up and stopping the engine: this will ensure the good lubrication of the turbo at the start and facilitate the slowing down process before it is switched

More information

Combustion Systems What we might have learned

Combustion Systems What we might have learned Combustion Systems What we might have learned IMechE ADSC, 6 December 2012 Chris Whelan Contents Engines Big & Small Carnot, Otto & Diesel Thermodynamic Cycles Combustion Process & Systems Diesel & Otto

More information

L34: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Introduction to Gas Cycles Definitions

L34: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Introduction to Gas Cycles Definitions Page L: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Review of Carnot Power Cycle (gas version) Air-Standard Cycles Internal Combustion (IC) Engines - Otto and Diesel Cycles

More information

(v) Cylinder volume It is the volume of a gas inside the cylinder when the piston is at Bottom Dead Centre (B.D.C) and is denoted by V.

(v) Cylinder volume It is the volume of a gas inside the cylinder when the piston is at Bottom Dead Centre (B.D.C) and is denoted by V. UNIT II GAS POWER CYCLES AIR STANDARD CYCLES Air standard cycles are used for comparison of thermal efficiencies of I.C engines. Engines working with air standard cycles are known as air standard engines.

More information

Comparative performance and emissions study of a lean mixed DTS-i spark ignition engine operated on single spark and dual spark

Comparative performance and emissions study of a lean mixed DTS-i spark ignition engine operated on single spark and dual spark 26 IJEDR Volume 4, Issue 2 ISSN: 232-9939 Comparative performance and emissions study of a lean mixed DTS-i spark ignition engine operated on single spark and dual spark Hardik Bambhania, 2 Vijay Pithiya,

More information

ABSTRACT. Electronic fuel injection, Microcontroller, CNG, Manifold injection. Manifold injection with uniflow scavenging.

ABSTRACT. Electronic fuel injection, Microcontroller, CNG, Manifold injection. Manifold injection with uniflow scavenging. ABSTRACT Key Words: Electronic fuel injection, Microcontroller, CNG, Manifold injection. Manifold injection with uniflow scavenging. Manifold injection with uniflow stratified scavenging. Direct CNG injection.

More information

AME 436. Energy and Propulsion. Lecture 6 Unsteady-flow (reciprocating) engines 1: Basic operating principles, design & performance parameters

AME 436. Energy and Propulsion. Lecture 6 Unsteady-flow (reciprocating) engines 1: Basic operating principles, design & performance parameters AME 436 Energy and Propulsion Lecture 6 Unsteady-flow (reciprocating) engines 1: Basic operating principles, design & performance parameters Outline Classification of unsteady-flow engines Basic operating

More information

2013 THERMAL ENGINEERING-I

2013 THERMAL ENGINEERING-I SET - 1 II B. Tech II Semester, Regular Examinations, April/May 2013 THERMAL ENGINEERING-I (Com. to ME, AME) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~~~

More information

The Effect of Efi to the Carbureted Single Cylinder Four Stroke Engine

The Effect of Efi to the Carbureted Single Cylinder Four Stroke Engine Journal of Mechanical Engineering Vol. 7, No. 2, 53-64, 2010 The Effect of Efi to the Carbureted Single Cylinder Four Stroke Engine Idris Ibrahim Adibah Abdul Jalil Shaharin A. Sulaiman Department of Mechanical

More information

Gas Power Cycles. Tarawneh

Gas Power Cycles. Tarawneh Gas Power Cycles Dr.Mohammad Tarawneh ) Carnot cycle 2) Otto cycle ) Diesel cycle - Today 4) Dual Cycle 5) Stirling cycle 6) Ericsson cycles 7) Brayton cycle Carnot Cycle Reversible isothermal expansion

More information

4. FUEL SYSTEM CK 1 4-0

4. FUEL SYSTEM CK 1 4-0 4 4 4-0 SERVICE INFORMATION... 4-1 FLOAT LEVEL INSPECTION... 4-5 TROUBLESHOOTING... 4-2 CARBURETOR INSTALLATION... 4-6 THROTTLE VALVE DISASSEMBLY... 4-3 THROTTLE VALVE ASSEMBLY... 4-6 CARBURETOR REMOVAL...

More information

EEN-E2002 Combustion Technology 2017 LE 3 answers

EEN-E2002 Combustion Technology 2017 LE 3 answers EEN-E2002 Combustion Technology 2017 LE 3 answers 1. Plot the following graphs from LEO-1 engine with data (Excel_sheet_data) attached on my courses? (12 p.) a. Draw cyclic pressure curve. Also non-fired

More information

Kul Internal Combustion Engine Technology. Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5

Kul Internal Combustion Engine Technology. Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5 Kul-14.4100 Internal Combustion Engine Technology Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5 Definitions Combustion engines convert the chemical energy of fuel to mechanical

More information

AIRCRAFT GENERAL KNOWLEDGE (1) AIRFRAME/SYSTEMS/POWERPLANT

AIRCRAFT GENERAL KNOWLEDGE (1) AIRFRAME/SYSTEMS/POWERPLANT 1 In flight, a cantilever wing of an airplane containing fuel undergoes vertical loads which produce a bending moment: A highest at the wing root B equal to the zero -fuel weight multiplied by the span

More information

2. Discuss the effects of the following operating variables on detonation

2. Discuss the effects of the following operating variables on detonation Code No: RR220303 Set No. 1 II B.Tech II Semester Regular Examinations, Apr/May 2006 THERMAL ENGINEERING-I ( Common to Mechanical Engineering and Automobile Engineering) Time: 3 hours Max Marks: 80 Answer

More information

Ignition control. The ignition system tasks. How is the ignition coil charge time and the ignition setting regulated?

Ignition control. The ignition system tasks. How is the ignition coil charge time and the ignition setting regulated? 1 Ignition control The ignition system tasks To transform the system voltage (approximately 14 V) to a sufficiently high ignition voltage. In electronic systems this is normally above 30 kv (30 000 V).

More information

3. At sea level, the atmosphere exerts psi of pressure on everything.

3. At sea level, the atmosphere exerts psi of pressure on everything. 41 Chapter Gasoline Injection Fundamentals Name Instructor Date Score Objective: After studying this chapter, you will be able to explain the construction, operation, and classifications of modern gasoline

More information

Kul Internal Combustion Engine Technology

Kul Internal Combustion Engine Technology Kul-14.4100 Internal Combustion Engine Technology Gas Exchange, 2015 Topics Gas exchange in four stroke engines Volumetric efficiency Valves and valve flow Two stroke engine scavenging Camshaft and intake

More information

www.thecarproblems.com/automotive-service-centre How You Diagnose Your Car Problems And Save Money A Quick Look At An Automotive Service Turbo For Your Car - Benefits, Precautions And Just How Does It

More information

Port Fuel Injection (PFI) Strategies for Lean Burn in Small Capacity Spark Ignition Engines

Port Fuel Injection (PFI) Strategies for Lean Burn in Small Capacity Spark Ignition Engines ISSN 2395-1621 Port Fuel Injection (PFI) Strategies for Lean Burn in Small Capacity Spark Ignition Engines #1 Shailendra Patil, #2 Santosh Trimbake 1 shailendrapatil7592@gmail.com 2 santoshtrimbake@yahoo.co.in

More information

5. Control System CONTROL SYSTEM FUEL INJECTION (FUEL SYSTEM) A: GENERAL. FU(STi)-27

5. Control System CONTROL SYSTEM FUEL INJECTION (FUEL SYSTEM) A: GENERAL. FU(STi)-27 W1860BE.book Page 27 Tuesday, January 28, 2003 11:01 PM 5. Control System A: GENERAL The ECM receives signals from various sensors, switches, and other control modules. Using these signals, it determines

More information

SUPERCHARGER AND TURBOCHARGER

SUPERCHARGER AND TURBOCHARGER SUPERCHARGER AND TURBOCHARGER 1 Turbocharger and supercharger 2 To increase the output of any engine more fuel can be burned and make bigger explosion in every cycle. i. One way to add power is to build

More information

This Service Information bulletin supersedes SI B dated December 2007.

This Service Information bulletin supersedes SI B dated December 2007. Page 1 of 5 SI B 13 01 07 Fuel Systems February 2008 Technical Service This Service Information bulletin supersedes SI B13 01 07 dated December 2007. designates changes to this revision SUBJECT Fuel Injection

More information

5. FUEL SYSTEM FUEL SYSTEM 5-0

5. FUEL SYSTEM FUEL SYSTEM 5-0 5 FUEL SYSTEM 5-0 SERVICE INFORMATION GENERAL INSTRUCTIONS SERVICE INFORMATION...5-1 CARBURETOR INSTALLATION...5-9 TROUBLESHOOTING...5-1 PILOT SCREW ADJUSTMENT...5-10 CARBURETOR REMOVAL...5-2 AUTO BYSTARTER...5-3

More information

Typical Fuel Systems - An Overview

Typical Fuel Systems - An Overview Typical Fuel Systems - An Overview Richard Skiba Skiba, R. (1999). Typical Fuel Systems An Overview, Pacific Flyer, March. Skiba, R. (2001). 'Typical Fuel Systems - An Overview'. Air Sport: The Home of

More information

International Journal of Scientific & Engineering Research, Volume 7, Issue 8, August-2016 ISSN

International Journal of Scientific & Engineering Research, Volume 7, Issue 8, August-2016 ISSN ISSN 2229-5518 2417 Experimental Investigation of a Two Stroke SI Engine Operated with LPG Induction, Gasoline Manifold Injection and Carburetion V. Gopalakrishnan and M.Loganathan Abstract In this experimental

More information

INTERNAL COMBUSTION ENGINE (SKMM 4413)

INTERNAL COMBUSTION ENGINE (SKMM 4413) INTERNAL COMBUSTION ENGINE (SKMM 4413) Dr. Mohd Farid bin Muhamad Said Room : Block P21, Level 1, Automotive Development Centre (ADC) Tel : 07-5535449 Email: mfarid@fkm.utm.my HISTORY OF ICE History of

More information

TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: FAX:

TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: FAX: TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: +353 66 7121911 FAX: +353 66 7124503 e-mail: sales@tillotson.ie HU SERIES SERVICE MANUAL INTRODUCTION To keep apace of new market

More information

Combustion engines. Combustion

Combustion engines. Combustion Combustion engines Chemical energy in fuel converted to thermal energy by combustion or oxidation Heat engine converts chemical energy into mechanical energy Thermal energy raises temperature and pressure

More information

FUEL SYSTEM/CARBURETOR/FUEL PUMP

FUEL SYSTEM/CARBURETOR/FUEL PUMP 13 FUEL SYSTEM/CARBURETOR/FUEL PUMP FUEL SYSTEM-------------------------------------------------------------------------------------13-1 SCHEMATIC DRAWING-------------------------------------------------------------------------13-2

More information

Chapter 6. NOx Formation and Reduction in Reciprocating Internal Combustion Engines (RICE)

Chapter 6. NOx Formation and Reduction in Reciprocating Internal Combustion Engines (RICE) Chapter 6 NOx Formation and Reduction in Reciprocating Internal Combustion Engines (RICE) Editor s Note: Chapter 6 NOx Formation and Reduction in Reciprocating Internal Combustion Engines (RICE) was written

More information

03. Fuel and Air Feed System

03. Fuel and Air Feed System Page 11 of 03. Fuel and Air Feed System Content (16 Marks) 3.1 Petrol fuel supply system. 8 Marks Conventional Petrol Engine: Gravity feed, Pump feed (Layout,Function of Components and location). Construction

More information