Chevy Sonic 1.4L Intake Manifold
|
|
- Griffin Lindsey
- 5 years ago
- Views:
Transcription
1 Chevy Sonic 1.4L Intake Manifold Install Time: 3 hours In the Box: (1) Racer X Intake manifold (6) M8x1.25 bolts (4) M6x1 bolts (2) 1/8 NPT plugs (1) 3/8 NPT plug (1) 1/4 NPT 90 degree barb (4) Small O-rings (1) Large O-ring (1) PCV O-ring Tools: Socket driver 10mm socket 13mm socket Pliers Crescent wrench Razor blade NPT thread sealer Flat head screwdriver Allen keys Instructions: 1. Start by removing the OEM air intake assembly and intake manifold. We suggest following the service manual, although there are several online sites with removal instructions. We recommend removing the fuel rail from the vehicle. This means relieving fuel pressure from the rail. Please do so in a safe manner and again follow the service manual for this procedure. 2. Optional PCV kit shown. Use pipe thread sealer on all fittings. Only 2 clamps are supplied with the kit. They should be used where indicated. Be sure to check valve flow is in the correct orientation during installation. (Figure 1) 3. The fuel rail mounting brackets must be bent to accommodate the mounts on the intake manifold. We suggest using a set of pliers and a crescent wrench. Slowly bend the tabs down toward the injectors. Check the rail fitment, the tabs should be parallel to the mounting points on the manifold. (Figure 2) 4. Once the fuel rail is ready to be installed onto the manifold begin by lubricating the injector o-rings. Once properly lubricated, angle the rail at the bottom toward the injector ports. (Figure 3) 5. Slowly insert the injectors into the manifold, firmly press from the top of the fuel. The plastic guides below the o-rings may bind slightly, this is normal. Take your time and be sure not to tear an o-ring. A fully seated injector should look like this. (Figure 4) 2018 Racer X Fabrication
2 6. Finally insert the small nylon spacers between the rail mounts and the manifold mount. Then thread in the M6x1 bolts to the bottom of the manifold and finger tighten. Once both are installed, use a 10mm socket to tighten bolts. (Figure 5) 7. Install manifold to cylinder head. It helps to remove the evap hose and canister for additional clearance and room to work. Before bolting the manifold to the cylinder head, install the injector electrical connectors. Then using the supplied (6) M8x1.25 bolts, mount the manifold to the cylinder head. Remember to ground the rail to one of the bolts. Once in place, tighten bolts to 15ft/lbs. 8. Next install the OEM throttle body using the supplied M6x1 40mm bolts. Start all bolts before tightening, use a 10mm socket and tighten throttle body. Install IC tube and tighten clamp. (Figure 6) 9. Install vacuum fittings, plugs and MAF sensor. We recommend using a thread sealing paste over tape. The thread sizes on the manifold are as follows: (2) 1/8 NPT, (1) 1/4 NPT, (1) 3/8 NPT, (1) M6x1 for MAF sensor. (Figure 7) 10. The OEM thermoset line must be cut from the brake booster on the master cylinder. Using a razor blade, carefully score the line so it can be separated from the fitting. Once removed, run the supplied 3/8 ID line from the fitting to the supplied 90 degree 1/4 NPT barbed fitting. (Figure 8) 11. The brake booster line can be seen here. (Figure 9) 12. Using the supplied 1/4 ID hose, run from the turbo BPV to the solenoid and manifold using the supplied 3/16 vacuum tee. The small 5/32 hose should be used to connect to the solenoid. The red silicone caps should be placed according to the picture. Be sure to use zip ties or clamps on the 1/4 line at the tee connection. (Figure 10-11) 13. The line routing can be seen in these additional pictures. (Figure 12-13) 14. Run the 1/2 ID hose from the PCV tee to the turbo vacuum source. The OEM PCV line will have to be cut from the OEM turbo fitting. Again, using a razor blade, score the thermoset line and remove. Using the supplied 5/8 hose connect the OEM fitting using the 1/2 to 5/8 hose splice connect the two hoses. (Figure 14-15) 15. Finally, install EVAP canister and line to manifold. The OEM fitting snaps into the top of the manifold. The small plastic wiring harness located at the center of the manifold will need to be removed to allow for more movement. Install all OEM electrical connectors, fuel system components and air intake assembly. Key on vehicle and check for fuel leaks, if there are no leaks start vehicle. Again double check for leaks. Installation complete. (Figure 16) 2018 Racer X Fabrication
3 2018 Racer X Fabrication
4 2018 Racer X Fabrication
5 2018 Racer X Fabrication
6 Questions, comments, or concerns? Racer X Fabrication
2015+ WRX Turbo Inlet Hose
2015+ WRX Turbo Inlet Hose 2018-04-25 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
More informationINSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT
INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT MITSUBISHI LANCER EVOLUTION X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM
More informationINSTALLATION INSTRUCTIONS FUEL RAIL
INSTALLATION INSTRUCTIONS FUEL RAIL MITSUBISHI EVO X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM PREPARING THE VEHICLE:
More informationIAG Street Series Air / Oil Separator (AOS) For 2017 WRX
P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
IAG Street Series Air / Oil Separator (AOS) For 2008-14 WRX Part# IAG-ENG-7100 Tools Required: Ratchet, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver, hose clamping
More informationAPIKOL AAN INTAKE MANIFOLD INSTALLATION INSTRUCTIONS
APIKOL AAN INTAKE MANIFOLD INSTALLATION INSTRUCTIONS Estimated Installation Time: Approximately 2 hours Parts that will need to be modified/removed (Details provided later in the instructions): Intercooler
More informationIAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI
IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7100 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat
More informationINSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT
INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT 2015+ SUBARU WRX (LHD ONLY) Document: 19-0136 Support: info@radiumauto.com This document covers the installation of the Radium brake master cylinder brace
More informationIAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI
IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat
More informationIAG Competition Series Air / Oil Separator (AOS) For 2017 STI
P IAG Competition Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7251 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationWrenches: ⅞, 8mm, 10mm, 13mm, 19mm P. allen, Other: Electrical Tape
IAG Street Series Air / Oil Separator (AOS) For 2008-14 STI Part# IAG-ENG-7100 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More information8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles)
P IAG Street Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7151 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationIAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI
IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat
More informationThese instructions were written for reference only and the use of a factory service manual is recommended.
Introducing the CorkSport High Pressure Fuel Line designed for the MZR DISI. This fuel line is designed to replace the OEM fuel line which are prone to failure at the brazed connection at the rail. The
More informationIAG Competition Series Air / Oil Separator (AOS) For WRX
P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationThese instructions were written for reference only and the use of a factory service manual is recommended.
Introducing the CorkSport High Pressure Fuel Line designed for the MZR DISI. This fuel line is designed to replace the OEM fuel line which are prone to failure at the brazed connection at the rail. The
More informationPerformance Inlet Manifold
Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with
More informationRotated Tuner Kit for Garrett GT Turbos
Rotated Tuner Kit for Garrett GT Turbos 031411 Thank you for purchasing the PERRIN performance rotated turbo kit. Installation of this turbo should only be performed by persons experienced in the installation
More informationIAG Air / Oil Separator (AOS) For STi
IAG Air / Oil Separator (AOS) For 2008-14 STi Part# IAG-ENG-7000 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors Sockets: 10mm, 12mm 13mm Wrenches: 10mm,
More information2014+ Ram 3.0 EcoDiesel EGR Delete
2014+ Ram 3.0 EcoDiesel EGR Delete Installation Guide WARNING: This product is for competition use only in a sanctioned racing event. NOT FOR USE ON VEHICLES USED OR REGISTERED FOR USE ON A PUBLIC ROAD
More informationINSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support:
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: info@radiumauto.com These instructions are based on a vehicle with an OEM turbocharger
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT
More informationTurner M50 Manifold Adapter Install. April 26, 2012
April 26, 2012 Models: 1996-99 E36 328i/M3; 1997-98 E39 528i, 1997-98 Z3 2.8, 1998-2000 MZ3 S52 Product(s): Turner M50 Manifold Adapter Kit Subject: Installation Guidelines and Tips This guide will aid
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationThank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc.
Thank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc. We took much pride in putting together a fuel system that would deliver a maximum amount of fuel as simply as possible
More informationWeistec M156/M159 ENGINE
Weistec M156/M159 ENGINE Oil / Air Separator System Installation Guide 2007-2011 S63 AMG 2007-2011 ML63 AMG 2007 R63 AMG 2007-2008 CLK63 AMG 2008 CLK63 Black Series 2007-2011 CLS63 AMG 2008-Present C63
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1-19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT
More informationVacuum and air hose replacement -- replacing all the old, crusty air and vacuum hoses under and around
Vacuum and air hose replacement -- replacing all the old, crusty air and vacuum hoses under and around the intake manifold. Requires removing the intake manifold. While you've got the intake manifold off,
More informationHush-O-Matic MRS Control Package
Hush-O-Matic MRS Control Package 06-49192 Congratulations on your purchase! The Hush-O-Matic MRS Control package allows you to choose a few different modes including always quiet and always loud. Controlling
More informationIntake Manifold Replacement
Document ID# 738735 2002 Chevrolet Chevy Suburban - 4WD Print Intake Manifold Replacement Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may
More informationINSTALLATION INSTRUCTIONS Dual Catch Can Kit Subaru Turbo and STi Document# Support:
INSTALLATION INSTRUCTIONS Dual Catch Can Kit 02-14 Subaru Turbo and 2015+ STi Document# 19-0099 Support: info@radiumauto.com This document covers the installation of a Radium dual catch can kit for the
More informationFord 6.7 EGR Delete Kit
Fits: 2011 12 Powerstroke 6.7L Read instructions thoroughly before proceeding! ***This kit may void factory warranty please check with manufacturer.*** ***This kit is intended for off road use only.***
More informationInstant Chat off the main page of Or simply call our tech team at
Adjustable Fuel Pressure Regulator Kit for 2008+STI 2018-10-03 PSP-FUL-301 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationIncluded parts: 1 - New Bosch CP3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Bracket/ Hardware STEP 1
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please contact H&S Motorsports
More information1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST
1/6/04 1501 Industrial Way N., Toms River, NJ 08755 732-349-2109 Fax:732-244-0867 MODERATE - Installation requires metric tools and possibly cutting and drilling. The ability to closely follow instructions
More informationINSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi These instructions are based on a vehicle with an OEM turbocharger and top-mount intercooler. If a front-mount
More informationIntegrated Engineering MK7 & MQB Catch Can Kit Install
Integrated Engineering MK7 & MQB Catch Can Kit Install Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation of Integrated Engineerings
More informationInstant Chat off the main page of Or simply call our tech team at
Subaru WRX/STI Air Oil Separator for Front Mounted Intercooler Setups 2013-02- 22 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT MITSUBISHI EVOLUTION X Document# Customer Support:
The EVOX catch can kit is available in 3 variations. The PCV kit installs between the PCV valve and the intake manifold. The crankcase kit installs between the valve cover vent port and the pre-turbo air
More informationLML 3 Y-Bridge Kit or High Flow Intake Bundle Package
2011-2016 LML 3 Y-Bridge Kit or High Flow Intake Bundle Package Covers installation of PN s: WCF100607, WCF100691, WCF100716, & WCF100353 Note: This Kit is for off road competition use only! Overview-
More informationParts List See cover Page
Thank you for purchasing the CorkSport Front Mount Intercooler Kit for the 2010-2013 Mazdaspeed 3. Keep your BAT s under check with the CorkSport FMIC Kit with the small or large intercooler. Please let
More information7 th Gen. Celica GTS Turbo Kit Installation Guide This kit has not been CARB approved and is intended for racing / offroad purposes only.
7 th Gen. Celica GTS Turbo Kit Installation Guide This kit has not been CARB approved and is intended for racing / offroad purposes only. The purpose of this guide is to serve as a reference for use when
More informationAMS F1-I INTAKE MANIFOLD
AMS F1-I INTAKE MANIFOLD The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs AMS will never compromise
More informationAMS EVO X Fuel Pressure Regulator Kit
AMS EVO X Fuel Pressure Regulator Kit The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs AMS will
More informationCOBB 3-Port Electronic Boost Control Solenoid
COBB 3-Port Electronic Boost Control Solenoid Mitsubishi Evolution X / Ralliart Congratulations on your purchase of the COBB Tuning 3-Port Electronic Boost Control Solenoid. The following instructions
More informationPerformance Air Intake, 2015+
PARTS LIST AND PARTS LIST 1PC ALUMINUM INTAKE PIPE 1PC HIGH-FLOW, OILED AIR FILTER 1PC SILICONE INDUCTION HOSE 1PC AIRBOX 1PC 1/16 RUBBER STRIPPING, 9 LENGTH 1PC 1/16 RUBBER STRIPPING, 8.5 LENGTH 1PC WORM-GEAR
More informationInstant Chat off the main page of Or simply call our tech team at
08+ Rotated Tuner Kit for Garrett GT Turbos 2016-11-03 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation
More information4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side
2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and
More information#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
More informationShotgun Double Barrel HPFP install guide
Shotgun Double Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Double Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationCOBB 3-Port Electronic Boost Control Solenoid
COBB 3-Port Electronic Boost Control Solenoid MazdaSpeed3/Mazdaspeed6 Congratulations on your purchase of the COBB Tuning 3-Port Electronic Boost Control Solenoid. The following instructions will assist
More informationPre-Installed. 1 Seal Kit 10 Silicone O-ring, 3/32 W, Intake Port Seals 1 Throttle Body Seal
Atomic AirForce Intake Manifold for LS7, 2006-2013 Corvette and 2014 Z28 Camaro - PN 2701 LS2, 2005-2007 Corvette and CTS-V, 2005-2006 GTO and SSR PN 2702 LS1/6*, 1997-2004 Corvette, 1998-2002 Camaro/Firebird,
More informationInstant Chat off the main page of Or simply call our tech team at
FRONT MOUNT INTERCOOLER 2015+ WRX 2017-07-07 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of
More informationALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper)
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 1 of 21 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationFRS/BRZ Air Oil Separator (AOS) Installation Manual
FRS/BRZ Air Oil Separator (AOS) Installation Manual Eric Hazen Rev. 2 Overview: Detailed instructions on installing the AOS for the FRS/BRZ/GT86. Difficulty: Beginner Time required: 1-3 hours depending
More informationSteeda S197 Mustang Whipple Supercharger Drive
Steeda S197 Mustang Whipple Supercharger Drive Parts List Qty. Description 1 Whipple supercharger snout 1 Whipple snout collar 1 10-rib supercharger pulley 1 10-rib crank pulley 1 10-rib belt tensioner
More information2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #
2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009
More information08-18 STI Flex Fuel Bluetooth Mk2 Kit Install Instructions For Cobb Tuning Access Port
For Cobb Tuning Access Port Delicious Tuning 1948 Don Lee Place Suite #7 Escondido, CA 92029 408-480-0995 Rough Draft BJP Rev: 2.0 Date: 2/1/17 FFBT parts: (1) Ethanol Content Analyzer Module (1) Ethanol
More informationShotgun Single Barrel HPFP install guide
Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationInstant Chat off the main page of Or simply call our tech team at
02-07 WRX/STI Air Oil Separator for Top Mounted Intercooler Setups 2013-02- 27 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons
More information03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions
Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationM-9424-M50CJ INTAKE MANIFOLD INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FIESTA ST Document: 19-0175 Support: info@radiumauto.com STEPS 1-14 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0377) STEPS 15-35 COVER THE CRANKCASE CATCH CAN
More informationEXPANSION TANK PARTS LIST AND INSTALLATION GUIDE
PARTS LIST AND INSTALLATION GUIDE PARTS LIST 2 PC APPLICATION-SPECIFIC MOUNTING BRACKETS 2 PC BLACK, ANODIZED 6061 ALUMINUM CATCH CANS 4 PC SILICONE HOSES 4 PC PLASTIC BARBED FITTINGS 4 PC WORM-GEAR CLAMPS
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More informationINSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-17 CHEVROLET CRUZE 1.4T ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK
More informationSlingshot Rotrex Supercharger Kit
Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you
More information2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE
More informationINSTALLATION INSTRUCTIONS PORT INJECTION KIT (PIK)
INSTALLATION INSTRUCTIONS PORT INJECTION KIT (PIK) 2017+ HONDA CIVIC TYPE-R, K20C1 Document: 19-0194 Support: info@radiumauto.com IMPORTANT NOTES: Installa on must be performed by an experienced technician.
More informationIntake Manifold Replacement
Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:
More informationMazda 3 & Mazdaspeed 3 Oil Cooler Installation Instructions
Page1 2007-2009 Mazda 3 & Mazdaspeed 3 Oil Cooler Installation Instructions Tooling: Jack and jack stands or a lift Socket wrench and torque wrench 10mm and 14mm sockets 3/16 Allen wrench 10mm wrench Pliers
More informationITEM QTY CHECK PART NUMBER DESCRIPTION
PART #21128 2010 Camaro Cold Air Induction Stage II PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1.
More informationJBR MAZDASPEED
Page1 james Barone Racing Aftermarket Parts and Accessories JBR 2007 2009 MAZDASPEED 3 Front Mount Intercooler Piping Kit Installation Instructions for TR8 Intercooler Tooling: o Jack, Jack Stands, Ramps
More informationCOBB Fuel Pressure Regulator Kit
315100 COBB Fuel Pressure Regulator Kit 2008+ Subaru STI Congratulations on your purchase of the COBB Tuning Fuel Pressure Regulator Kit for your 2008+ Subaru STI. The following instructions will assist
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Part# 22-7810 Jeep JK/JKU ARB Mounting Kit 2007-2018.5 For the most up to date instructions please visit www.updownair.com www.updownair.com 833 226 4863 IMPORTANT INFORMATION
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER DS (GUN METAL GRAY FINISH)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-823DS (GUN METAL GRAY FINISH) 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-202DOSK AIR FILTER; OFFSET 2.75" X
More informationInstallation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM
Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM 1995-1997 Land Cruiser * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg A, Ventura, CA 93003 (805) 642-8833 phone *
More informationINSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support:
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: info@radiumauto.com These instructions are based on a vehicle with an OEM turbocharger
More informationSR Performance Twin 62mm Throttle Body for GT
Required Tools: SR Performance Twin 62mm Throttle Body for 2005-2010 GT Flat-head screwdriver Ratchet Small extension 10mm socket 8mm socket T20 Torx bit Needle nose pliers 5mm allen wrench Recommended
More informationIntake Manifold Removal
PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS Parts included: -GT350 Intake manifold M-944-M5 -GT350 Air bucket w/filter.
More informationb o o s t r e t a i n e r v a l v e
b o o s t r e t a i n e r v a l v e i n s t a l l a t i o n i n s t r u c t i o n s For questions or tech support, CONTACT US! Email: greg@hiperformancestore.com sales@hpsimotorsports.com Sites: www.hiperformancestore-fiat.com
More informationAPR, LLC 1027-B Opelika Road Auburn Alabama 36830
B6 A4 INJECTOR INSTALLATION L A T I N Tool Needed: - Flathead Screwdriver (large) - Flathead Screwdriver (small) - Ratchet - 5mm Allen Socket If you are using the APR Injectors, you will also need the
More informationAlways wear safety glasses when working on your vehicle.
90-93 MAZDA MIATA SUPERCHARGER KIT The KraftWerks 90-93 Mazda Miata Supercharger Kit was designed for easy installation. Competent mechanics with the appropriate tools will find the process to be relatively
More informationEdelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle), 6.1L and 6.4L Gen III HEMI Engines Part #7179
For Chrysler 5.7L (Eagle), 6.1L and 6.4L Gen III HEMI Engines PLEASE study these instructions carefully before beginning this installation. You should be familiar with and comfortable working on your
More informationWRX/STI COLD AIR INTAKE PSP-INT-322BK & PSP-INT-322RD
Vehicle Fitment Chart: 2015 SUBARU WRX STI H4-2.5L Turbo 2012-2014 SUBARU WRX STI H4-2.5L Turbo 2012-2014 SUBARU WRX H4-2.5L Turbo 2009-2011 SUBARU WRX STI H4-2.5L Turbo 2009-2011 SUBARU WRX H4-2.5L Turbo
More informationSTEALTH BIG AIR KIT - Yamaha Roadliner/Stratoliner and Raider
Page: 1 If you question your abilities it may be best for an experienced service technician perform this installation. A Yamaha Service Manual would be helpful to have on hand for reference. Revision:
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationHolley Ford 351W Hi-Ram Modular Intake Manifold Kits
Holley Ford 351W Hi-Ram Modular Intake Manifold Kits Holley P/N Engine Application & Induction Configuration 300-241 Hi-Ram, 1 x 95mm LS Throttle Body (longitudinal mount) w/ port EFI provisions & fuel
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: C
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-721C 2011-2013 MINI Cooper S L4-1.6L SEE NOTE* 2011-2013 MINI Clubman S L4-1.6L SEE NOTE* 2011-2013 MINI Cooper
More informationINSTALLATION INSTRUCTIONS DUAL OIL CATCH CAN KIT
INSTALLATION INSTRUCTIONS DUAL OIL CATCH CAN KIT SUBARU WRX FA20F ENGINE Document: 19-0135 Support: info@radiumauto.com This dual catch can kit installs in the right-hand side of the engine bay and intercepts
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FIESTA ST Document: 19-0175 Support: info@radiumauto.com STEPS 1-14 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0377) STEPS 15-31 COVER THE CRANKCASE CATCH CAN
More informationEdelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines Part #7179
For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines PLEASE study these instructions carefully before beginning this installation. You should be familiar with and comfortable working on your vehicle.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Part # 751-FP2500 IMPORTANT INFORMATION This Jagg oil cooler must be installed following these instructions. Read the easy-to-follow instructions fully prior to starting the installation
More informationInstant Chat off the main page of Or simply call our tech team at
FRONT MOUNT INTERCOOLER 2008-13 STI 2014-04- 08 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation
More information3/8 Universal Joint Phillips Head Screwdriver
Magnetic retrieval tool Pliers 1/4 Ratchet Drive T-35 Torx Socket 3/8 Ratchet Drive 5mm Allen Head Socket Torque Wrench 7-3/8 Drive Extension Flat Head Screwdriver 10mm Socket 8mm Socket 3/8 Universal
More information2011 Mercury Grand Marquis LS
Fig. 6: Locating Intake Manifold Crash Bracket With Tie Strap 24. Remove the intake manifold crash bracket bolt. 25. Disconnect the fuel rail pressure and temperature sensor vacuum and electrical connectors.
More information