Site Planning Guide. Staff Workstation Model M Library Systems. Printed in U.S.A. 3M 1999 July
|
|
- Kristina Barton
- 5 years ago
- Views:
Transcription
1 Site Planning Guide Staff Workstation Model 995 3M Library Systems 3M Center, Building 209-1W-09 St. Paul, MN Printed in U.S.A. 3M 1999 July
2 The customer is completely responsible for cutting the hole and installing the mounting brackets on the Staff Workstation Model 995. The 3M technician will complete the installation. In-Counter On-Counter Figure 1. Staff Workstation Model 995 In-Counter and On-Counter Installation To physically install the Model 995, the customer is responsible for: The Staff Workstation Model 995 can be installed on a counter or in a counter. In either case, the same placement requirements apply. The upper unit must be placed at least 12 inches [304 mm] away from all monitors. However, more space is better and if space permits 18 inches [457 mm] from any monitor is preferred. Ensuring that magnetically recorded media will always remain at least 6 inches [152 mm] away from the upper unit. The 3M service technician is to make all electrical connections to the Staff Workstation Model 995. The 3M service technician requires access to the front and back of the electronics box. The upper unit should be installed with no modification by the customer. The upper unit is designed to process books either in a right-to-left motion or left-to-right motion. The 3M service technician will install the scanner on the upper unit based on the position of the bar codes on your material. This will be done when the electrical portion of the installation is completed. Refer to Section 1.0 for in-counter installation and to Section 2.0 for on-counter installation. 3M 1999 July 1
3 Optional Power Supply AC outlet required with some library terminals. Refer to Staff Workstation Model 995 Customer Checklist. Scanner Keyboard Upper Unit Counter To PC To Keyboard ft. [1,8 m] Cable to Electronics Box 6 ft. [1,8 m] Data Cable 6 ft. [1,8 m] Power Cord Figure 2. Staff Workstation Model 995 Components Electronics Box Service Switch A Model 995 Power Supply (Optional) Scanner Upper Unit Library Terminal Electronics Box C Figure 3. Library Terminal and Staff Workstation Model 995 Components 2 3M 1999 July
4 1.625 in. [41 mm] 8.65 in. [219 mm] 6.77 in. [171 mm].75 in. [19.05 mm] 2.5 in. [63 m m] 1.56 in. [39.62 mm].34 in. [8.64 mm] 3.49 in. [88.65 mm] in. [387 mm].74in in. [18.80 mm] Upper Unit [ m m] Note: 3.71 in. Second Bracket [94.23 mm] is Mirror Image Bracket Bracket.33 in. [8.38 mm] 4.15 in. [ mm] 7.27 in. [185 mm] Upper Unit 4 in. [10.2 cm] 3.9 in. [10.0 cm] 1 in. [2.5 cm] 7 in. [177 mm] 6 ft. [1,8 m] Power Cord 17 in. 13 in. [431 mm] [330 mm] Electrical Box Electronics Box C Figure 4. Model 995 Dimensions 3M 1999 July 3
5 1.0 In-Counter Installation This installation method cannot be used if the counter top is less than 3/4 inch [19 mm] or more than 2-1/2 inches [63 mm] thick. Discuss alternative mounting methods with your maintenance personnel. A template and cutting instructions are packaged with the Model 995. Note All dimensions given in this document are for reference only. You must use the template that comes with the machine for a guide to cut the hole in a counter top. This is to be used with a router to cut a hole in the counter. 1. To physically install the Model 995 in-counter, the customer is responsible for: Cutting the hole in the circulation counter. Installing the mounting brackets. Ensuring the cable (6 feet) from the upper unit will reach and is accessible to the electronics box. Ensuring electrical power will be available for the Model 995. Power must be within reach of the 6 foot [1,8 m] power cord which comes from the electronics box. A switchable power strip is suggested to control power to the Model 995 electronics box, CRT terminal, printer, and wedge (optional). Ensuring there is adequate space beneath the counter top. Look under the counter to ensure the mounting area is clear of obstructions or support brackets. The upper unit requires an 18 inch wide, 9 inch long, 4 inch deep space under the counter top. Allowing room under the counter for the Staff Workstation electronics box: The electronics box must be located to allow connection to the 6 foot [1,8 m] cable from the upper unit and to the 6 foot [1,8 m] cable from the keyboard wedge. Ensuring the keyboard wedge is located within reach of the following connecting cables: Cable to your terminal is approximately 18 inches [457 mm] Cable to your keyboard cable is 8 inches [203 mm] Cable to electronics box is 6 feet [1,8 m] 2. 3M technicians are not authorized and are not equipped to physically install the Staff Workstation Model 995 in the counter. 3. Mounting brackets and wood screws are included to install the Model 995 in counter tops that are ¾ inch [19 mm] to 2-1/2 inches [63 mm] thick. The placement of the mounting brackets on the bottom of the upper unit varies for different thickness counter tops. Figure 5 shows the bracket layout for different counter tops. 4 3M 1999 July
6 3/4 to 1-7/16 Inches [19.05 to mm] 3/4 to 1-1/8 Inches [19.05 to mm] 1-1/2 to 2-1/4 Inches [38.10 to mm] 1-1/2 to 2-1/8 Inches [38.10 to mm] 1 to 1-7/16 Inches [25.4 to mm] 2 to 2-1/4 Inches [50.80 to mm] 1-7/16 to 1-5/8 Inches [36.51 to mm] 1-7/16 to 1-5/8 Inches [36.51 to mm] 2-1/4 to 2-1/2 Inches [57.15 to mm] 2-1/4 to 2-1/2 Inches [57.15 to mm] C Figure 5. Mounting Bracket Locations 3M 1999 July 5
7 2.0 On-Counter Installation To physically install the Model 995 on-counter, the customer is responsible for: Installing the upper unit on the counter top. Ensuring the cable (6 feet) from the upper unit will reach and is accessible to the electronics box. It is your option to drill a hole through the counter in a convenient place for this cable or to route the cable over the edge of the counter. This may result in the cable being in the work area. If the cable is routed through the counter, the customer is responsible for cutting the hole. Use a drill with a 2 inch [50 mm] diameter cutting blade to cut the hole. Allowing room under the counter for the Staff Workstation electronics box: The electronics box must be located to allow connection to the 6 foot [1,8 m] cable from the upper unit and to the 6 foot [1,8 m] cable from the keyboard wedge. Ensuring electrical power will be available for the Model 995. Power must be within reach of the 6 foot [1,8 m] power cord which comes from the electronics box. A switchable power strip is suggested to control power to the Model 995 electronics box, CRT terminal, printer, and wedge (optional). Ensuring the keyboard wedge is located within reach of the following connecting cables: Cable to your terminal is approximately 18 inches [457 mm] Cable to keyboard cable is 8 inches [203 mm] Cable to electronics box is 6 feet [1,8 m]. 6 3M 1999 July
5. Contractor Information 3M Model 2300 Series System Layout Checklist
5. Contractor Information 3M Model 2300 Series System Layout Checklist This checklist contains the information necessary to provide the environment required to successfully install your new Model 2300
More informationPreinstallation Worksheet 3M Detection Systems Please complete this form and fax it to 3M at
Preinstallation Worksheet 3M Detection Systems Please complete this form and fax it to 3M at 1-800-795-9091. Today s date Sales consultant Account name Key contact name Phone No. Installation location
More informationFLEXI-COIL 67 Series (1999+) Installation Manual FC1
FC1 FLEXI-COIL 67 Series (1999+) Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-FC1-INST Rev C (FLEXI-COIL 67 Series (1999+)) NOTICE: NORAC
More informationMS Sprayers NT 1000/1250 Installation Manual MS1
MS1 MS Sprayers NT 1000/1250 Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-MS1-INST Rev B (MS Sprayer NT 1000/1250) NOTICE: NORAC Systems
More informationSUMMERS Pull-Type with Proxy Switch Sense Installation Manual SM2
SM2 SUMMERS Pull-Type with Proxy Switch Sense Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-SM2-INST Rev B (SUMMERS Pull-Type with Proxy
More informationCondor Manual. Corporation
Condor Manual Corporation PREFACE IMPORTANT, PLEASE READ CAREFULLY Thank you for your purchase with Amico Accessories Inc. This unit is designed for long lasting performance, providing the end user complies
More informationHARDI Economy EAGLE Installation Manual HD9
HD9 HARDI Economy EAGLE Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-HD9-INST Rev C (HARDI Economy EAGLE) NOTICE: NORAC Systems International
More informationDetection System Model 8800 Series
Detection System Model 8800 Series rchitect/contractor Information Package 3M Library Systems 3M Center, Building 225-4N-14 St. Paul, Minnesota 55144-1000 www.3m.com/library 78-8126-7738-9_B Copyright
More informationSpray Height Controller
Spray Height Controller JD06 John Deere (4920) Installation Manual Printed in Canada Copyright 2009 by NORAC Systems International Inc. Reorder P/N: UC5-BC-JD06-INST Rev F (John Deere 4920) NOTICE: NORAC
More information5 Removal and replacement
5 Removal and replacement This chapter describes the removal and replacement of field-replaceable units (FRUs) only. Removal and replacement strategy User-replaceable parts Covers Internal assemblies ENWW
More informationFLEX-6000 Rack Mounting Bracket Installation Guide
FLEX-6000 Rack Mounting Bracket Installation Guide July 25, 2013 Thank you for purchasing the FLEX-6000 Rack Mounting Bracket Kit. The following guide will provide the necessary step-by-step procedure
More informationJohn Deere 4730, 4830 Installation Manual JD8
JD8 John Deere 4730, 4830 Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-JD8-INST Rev E (John Deere 4730, 4830) NOTICE: NORAC Systems International
More informationUSER MANUAL. Uninterruptible power supply MODEL: 53965,
USER MANUAL Uninterruptible power supply MODEL: 53965, 53966 www.qoltec.com Please check if the package contains: - UPS unit - Power cable (1 x SCHUKO) 1.2 m - User manual This UPS provides comprehensive
More informationSpray Height Controller
Spray Height Controller JD10 John Deere (4930) with Proportional Main Lift Installation Manual Printed in Canada Copyright 2009 by NORAC Systems International Inc. Reorder P/N: UC5-BC-JD10-INST Rev G (John
More informationRogator 64 and 74 Series and Willmar Eagle 8650 (JIC) & 84, 94 & 1386 Series (Flat Faced O-Ring) Installation Manual RG2 & RG6
RG2 & RG6 Rogator 64 and 74 Series and Willmar Eagle 8650 (JIC) & 84, 94 & 1386 Series (Flat Faced O-Ring) Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder
More informationFast Standard Control Installation Manual FT4
FT4 Fast Standard Control Installation Manual Printed in Canada Copyright 2015 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-FT4-INST Rev A (Fast - Standard Control) NOTICE: NORAC Systems International
More informationCIRCULATION DESKS Series Shown with Optional Decorative Fronts & Optional Radius Configuration
CIRCULATION DESKS 4400 Series Shown with Optional Decorative Fronts & Optional Radius Configuration CIRCULATION DESKS 4400 Series Shown with Optional Liberty Millwork Trim 4400 Series Shown with Optional
More informationOptional Extras 1. Part #AT7107A Privacy Handset 2. Part # HMN4058A Potato Mic.
The AdvanceTec Hands-free car kit is designed for use with all AdvanceTec car kit cradles as well as all Motorola OEM car kit cradles for safe and convenient vehicular operation. The Car Kit (AT6538A)
More informationRetractable Roll-up Banner Graphics
Retractable Roll-up Banner Graphics Sterling Roll-up Available in 4 sizes Upper bleed for system attachment Upper bleed for system attachment. All images embedded & fonts outlined. No layers, paths or
More informationMidmark Cabinet / Wall Light Installation
Midmark Cabinet / Wall Light Installation [Full size template is available: 003-1289-00] warning Equipment is not suitable for use in the presence of a flammable anesthetic mixture. Equipment Alert Before
More informationExceptional Value Improves Lighting Quality Reduces Energy Costs. Industrial Grade LED Task Lights
Exceptional Value Improves Lighting Quality Reduces Energy Costs Industrial Grade LED Task Lights 26528 26532-LED 26530-LED 26527 26526 26533-LED 26531-LED Industrial Grade LED Task Lights Exceptional
More informationLX HD Sit-Stand Wall Mount LCD Arm
ASSEMBLY INSTRUCTIONS LX HD Sit-Stand Wall Mount LCD Arm Maximum Screen Size* = 46 *Limited to 30 lbs maximum 14-30 lbs (6.35-13.61 kg) 180 180 360 20" (508 mm) 70 5 For the latest User Installation Guide
More informationStorage. Worksurfaces & Support See page Statement of Line. Mobile
Table of Contents Worksurfaces & Support Statement of Line 1 3 16" Worksurfaces page 328 1 9 16" Worksurfaces page 329 Transaction Counters page 330 Table Tops page 331 Support page 332 Planning Product
More informationHagie 264, 284XP, DTS8, 2100, 2101, DTS10 Installation Manual HG2
HG2 Hagie 264, 284XP, DTS8, 2100, 2101, DTS10 Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-HG2-INST Rev A (Hagie 264, 284XP, DTS8, 2100,
More informationInstallation Instructions
Installation Instructions Speedcook Oven Read carefully. Keep these Instructions. INSTALLATION INSTRUCTIONS Electrical Requirements Product rating is 240/208 volts AC, 60 Hertz, 30 amps and 6.5 kilowatts.
More informationIndustrial Grade LED Task Lights. Exceptional Value Improves Lighting Quality Reduces Energy Costs. aveninc.com
Exceptional Value Improves Lighting Quality Reduces Energy Costs Industrial Grade LED Task Lights Product_Sheets_Template_BrochureFinal.indd 1 26528 26532-LED 26530-LED 26533-LED 26531-LED 26527 26526
More informationMiller Condor & New Holland Rear Mount Truss Boom Installation Manual MC02
MC02 Miller Condor & New Holland Rear Mount Truss Boom Installation Manual Printed in Canada Copyright 2009 by NORAC Systems International Inc. Reorder P/N: UC5-BC-MC02-INST Rev F (Miller Condor & New
More informationGALANT. storage BUYING GUIDE
BUYING GUIDE GALANT storage QUALITY All main parts in GALANT storage series have been tested and approved for office use in accordance with European and North American safety requirements. Read more in
More informationRogator 854, 1054 & 1254 Series Installation Manual RG4
RG4 Rogator 854, 1054 & 1254 Series Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-RG4-INST Rev D (Rogator 854, 1054 & 1254 Series) NOTICE:
More informationJohn Deere (4730 & 4830) with Proportional Main Lift Installation Manual JD08
JD08 John Deere (4730 & 4830) with Proportional Main Lift Installation Manual Printed in Canada Copyright 2009 by NORAC Systems International Inc. Reorder P/N: UC5-BC-JD08-INST Rev N (John Deere 4730 &
More informationBANNER STANDS DISPLAYS
BANNER STANDS DISPLAYS INDOOR BANNER STANDS PREMIUM RETRACTABLE Durable, Silver Retractable Stand, & Telescoping Pole Hard Case Outer Dimensions 6.5 L x 6.5 W x 41 D Inner Dimensions 6.25 L x 5.5 W x 41.5
More informationFord 6.7L Installation of the Guardian Safety System
Ford 6.7L Installation of the Guardian Safety System Diesel Tech Industries Ltd. 14215-120 Avenue Edmonton, Alberta, Canada T5L 2R8 Phone: (780) 455-9876 info@dtiguardian.com www.dtiguardian.com DTI05-02.01/13
More informationHD4170 SETUP & OPERATOR MANUAL. Performance Design Inc East Braniff St. Boise, Idaho 83716
HD4170 SETUP & OPERATOR MANUAL Performance Design Inc. 2350 East Braniff St. Boise, Idaho 83716 www.rhin-o-tuff.com HD-4170 Rhin-O-Roll Coiler Operator s Training Manual Issue 1 03/05 PDI Part # 941000
More informationCUBO media furniture TYPE LIST
TYPE LIST p. 2-6 p. 7-8 p. 9-16 p. 17 p. 18 Programme / technical information Suggestions Body elements Accessories Top panels Valid from 1.8.2017 CUBO media furniture - the design The CUBO media furniture
More information2300 OPERATING/APPLICATION/INSTALLATION INSTRUCTIONS
2300 OPERATING/APPLICATION/INSTALLATION INSTRUCTIONS GENERAL The POWER ACCESS Model 2300 is an automatic door opener designed for opening and closing side hinged residential doors - both exterior and interior.
More informationOPTEVA 923 IN LOBBY TELLER (ILT) PLAN mm (60") WIDE PLAN - STAND ALONE FRONT VIEW SIDE VIEW PAGE 1 OF 5 CALL NOTE:
OPTEVA 9 IN LOBBY TELLER (ILT) mm ( ") U.L. SAFE L4 CALL -8-999-6 CONSULT WITH DIEBOLD INSTALLATION/SERVICE BRANCH FOR ADDITIONAL DETAILS AND INFORMATION. PLEASE SEE PLANNING AND SITE PREPARATION GUIDE
More informationINSTALLATION INSTRUCTIONS AM rev. A
INSTALLATION INSTRUCTIONS AM16629-1 rev. A READ THIS MANUAL CAREFULLY! FAILURE TO INSTALL THIS EQUIPMENT PER THESE INSTRUCTIONS WILL VOID THE WARRANTY. INTRODUCTION NOTE: Zebra technologies Corporation
More informationFOR WALL MOUNT COMBINATION ARMS
INSTALLATION MANUAL FOR WALL MOUNT COMBINATION ARMS LIGHT DUTY ARMS HEAVY DUTY ARMS KEYBOARD TRAY VERSION Weight Capacity 4-20 lbs KEYBOARD TRAY VERSION Weight Capacity 8-40 lbs WORKSTATION VERSION Weight
More informationPH3 AIR INTAKE EMERGENCY SHUT-OFF VALVE WITH POWERGUARD SMART OVERSPEED LIMITER. Generic PH3 Truck Shut-Off Valve Kit.
PH3 AIR INTAKE EMERGENCY SHUT-OFF VALVE WITH POWERGUARD SMART OVERSPEED LIMITER Generic PH3 Truck Shut-Off Valve Kit www.powerhalt.com INSTALLATION REQUIREMENTS & RECOMMENDATIONS: Prior to the installation,
More informationSelect a convenient position for the display on a panel or bulk head.
The Target wind speed and direction instrument is supplied complete with display unit, mast head sensor and mounting kit. It is designed to operate from the vessels 12v battery supply. PRETEST OF INSTRUMENT
More informationInstallation Manual VEHICLE HANDSFREE KIT KRY ericssonz
Installation Manual VEHICLE HANDSFREE KIT KRY 101 1613 ericssonz TABLE OF CONTENTS NOTICE! This manual covers Ericsson and General Electric products manufactured and sold by Ericsson Inc. This manual is
More informationSetup, Assembly, & Adjustment
Setup, Assembly, & Adjustment 34877 Rev. B 1 of 8 Melco Fast Clamp Instructions The Melco Fast Clamp is a versatile clamping system for your embroidery machine. This document will walk you through the
More informationCable Management System Installation Manual
Cable Management System Installation Manual TABLE OF CONTENTS 1.0 INTRODUCTION and SAFETY... 2 2.0 INSPECTION and UNPACKING... 2 3.0 GENERAL INSTALLATION... 2 4.0 UPPER MOUNTING... 5 4.1 Under Hung Loft
More informationABOUT. In 1973 Baertec Machinery took its place in Bursa Industry by producing Aluminium and Pvc & Metal Processing Machinery.
ABOUT US In 1973 Baertec Machinery took its place in Bursa Industry by producing Aluminium and Pvc & Metal Processing Machinery. In 1973 Baertec Machinery took its place in Bursa Industry by producing
More informationTender STEEL CANTILEVER SHELVING NE BRANCH LIBRARY APPENDIX B
Tender 010-0 STEEL CANTILEVER SHELVING NE BRANCH LIBRARY APPENDIX B Metal Shelving for NE Branch; end panels, counter tops and custom-made OPAC stands Shelving for the Children s materials Tag No. 1 Item
More informationLX Wall Mount Keyboard Arm
LX Wall Mount Keyboard Arm English For the latest User Installation Guide please visit: www.ergotron.com English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语 www.ergotron.com USA:
More informationOPTEVA 378 ENHANCED CASH RECYCLER TERMINAL FRONT LOAD LOBBY UNIT PLAN VIEW FRONT VIEW SIDE VIEW
L00 CALL -800--600 OPTEVA 8 ENHANCED CASH RECYCLER TERMINAL WITH mm ( ") UL SAFE 4 ( 6 ") 4 ( 6 ") CONSULT WITH DIEBOLD INSTALLATION/SERVICE BRANCH FOR ADDITIONAL DETAILS AND INFORMATION. PLEASE SEE PLANNING
More informationTrack Light with Monitor Installation Guide
Track Light with Monitor Installation Guide This installation requires at least two service technicians. Track with light and monitor weight (max.) is 157 Lbs. (71 kgs). Applies to Models: 1531017 (-000
More informationDM1016S INSTALLATION/OWNER'S MANUAL 10" Marine DVC Subwoofer
DM1016S INSTALLATION/OWNER'S MANUAL 10" Marine DVC Subwoofer DM1016S INSTALLATION Preparation/Installation Please read entire manual before installation. Before You Start Disconnect negative battery terminal.
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW REGULATOR (742-269) Ford Mustang 1996 2004 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationRogator Passive Roll (2012+) 3 Height Sensors Installation Manual RG10
RG10 Rogator Passive Roll (2012+) 3 Height Sensors Installation Manual Printed in Canada Copyright 2009 by NORAC Systems International Inc. Reorder P/N: UC5-BC-RG10-INST Rev D (Rogator Passive Roll (2012+)
More informationINSTALLATION MANUAL FOR PILOT WORKSTATION
INSTALLATION MANUAL FOR PILOT WORKSTATION Weight Capacity: 5-25 lbs. Monitor Weight: 5-20 lbs. 6011180 Rev. B Contents Tools Required / Supplied Part Kits / Warnings/Disclaimer...2 Possible Base Mounting
More informationNitro (4000 Series) Installation Manual NT04
NT04 Nitro (4000 Series) Installation Manual Printed in Canada Copyright 2009 by NORAC Systems International Inc. Reorder P/N: UC5-BC-NT04-INST Rev I (Nitro 4000 Series) NOTICE: NORAC Systems International
More informationPRSalpha Air Drill (Double Valve)
888-680-4466 ShopBotTools.com PRSalpha Air Drill (Double Valve) Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Overview...5 Spindle Mounting Plate...6
More informationLX Wall Mount LCD Arm
ASSEMBLY INSTRUCTIONS LX Wall Mount LCD Arm For the latest User Installation Guide please visit: www.ergotron.com User's Guide - English Guía del usuario - Español Manuel de l utilisateur - Français Gebruikersgids
More informationInstallation Instructions Table of Contents
Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft
More informationDouble head cutting machines
Double head cutting machines Machines for processing aluminium and PVC profiles Machines fully designed and manufactured in Italy THE COMPANY Pertici Industries, was founded in 1965 by Leto Pertici as
More informationModel 579 Curtain Machine Manual. General Information. Unpacking:
Model 579 Curtain Machine Manual. General Information The Model 579 curtain machine is designed for use with most light duty commercial and residential drapery tracks. The 579 curtain machine is designed
More informationInstallation Instructions
Installation Instructions Over The Range Microwave Oven BEFORE YOU BEGIN (Read these instructions completely and carefully.) IMPORTANT IMPORTANT Save these instructions for local inspector s use. Observe
More informationAvanti J Series Centrifuges Preinstallation
J325-TB-001AP February 2009 Avanti J Series Centrifuges Preinstallation INTRODUCTION Purchase of an Avanti J series centrifuge includes installation and Basic Instrument Training for two operators. This
More informationCase IH 3150, 3185, 3200, 3310, Tyler Patriot Installation Manual CS2
CS2 Case IH 3150, 3185, 3200, 3310, Tyler Patriot Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-CS2-INST Rev A (Case IH 3150, 3185, 3200,
More informationTop Air (1200/ /90 ft Boom) Installation Manual TA1
TA1 Top Air (1200/1600 80/90 ft Boom) Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-TA1-INST Rev A (Top Air (1200/1600 80/90 ft Boom)) NOTICE:
More informationhousevolve Garage Door Controller User Manual and Installation Guide
housevolve Garage Door Controller User Manual and Installation Guide Introduction Thank you for purchasing a FREEVOLVE product. We designed it to provide you with years of reliable service. The following
More information5700 SERIES Low Energy Power Operator
Low Energy Power Operator introduction Low energy door operators were once considered a necessity only for those with physical challenges. Today, due to the population s busy lifestyles, the convenience
More informationChargePoint Gateway Installation Instructions
ChargePoint Gateway Installation Instructions You must be a licensed electrician and complete online training (http://chargepointuniversity.netexam.com/) to become a ChargePoint Certified Installer, and
More informationAGCO América do Sul (Factory Install) Installation Manual SP01
SP01 AGCO América do Sul (Factory Install) Installation Manual Printed in Canada Copyright 2010 by NORAC Systems International Inc. Reorder P/N: UC5-BC-SP01-INST Rev G (AGCO Brazil Factory Install) NOTICE:
More informationPFW 6855 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids
Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids Max: 227kg/500lbs MOUIN_PFW6855_V01 Refer to Step: Included components 3 10
More informationUNIVERSAL PUMP HANGER INSTALLATION INSTRUCTIONS
UNIVERSAL PUMP HANGER INSTALLATION INSTRUCTIONS WARNING! THESE INSTRUCTIONS MUST BE READ AND FULLY UNDERSTOOD BEFORE BEGINNING INSTALLATION. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN POOR PERFORMANCE,
More informationAutoFarm GPS AutoSteer Hardware Installation Guide
AutoFarm GPS AutoSteer Hardware Installation Guide Supported Models: Case AFX-8010 Combines PN: 602-0039-01-A Special Requirements Tools This list consists of special tools required to complete the installation.
More informationINSTALLATION GUIDES OUTDOOR LIVING
S OUTDOOR LIVING TABLE OF CONTENTS 12 Volt 12 Watt DC Transformer Page 2 12 Volt 50 Watt DC Smart Transformer Page 3 12 Volt 50 Watt Smart Transformer Control Page 4-5 Waterproof Dimmer For 12W Transformer
More informationAsepsis 21 Delivery Unit
INSTALLATION INSTRUCTIONS for the Console Mounted TM Asepsis 21 Delivery Unit SECTION I - REQUIREMENTS 1. PHYSICAL REQUIREMENTS... 1 2. ELECTRICAL REQUIREMENTS... 1 3. WATER SUPPLY REQUIREMENTS... 1 4.
More informationOVER THE RANGE MICROWAVE OVEN INSTALLATION INSTRUCTIONS
OVER THE RANGE MICROWAVE OVEN INSTALLATION INSTRUCTIONS Please read all instructions thoroughly before installing the Over the Range Microwave Oven/Hood System. Two people are recommended to install this
More informationPreinstallation Requirements for Avanti J Series Centrifuges
J325-TB-001AQ June 2012 Preinstallation Requirements for Avanti J Series Centrifuges Introduction Purchase of an Avanti J series centrifuge includes installation and Basic Instrument Training for two operators.
More informationIT IS IMPORTANT THAT YOU OBTAIN THE CORRECT INFORMATION FOR YOUR VEHICLE, OR DAMAGE TO THE WIRING SYSTEM COULD OCCUR.
Instructions for Universal Harness PRINT THESE INSTUCTIONS Gentex Mirror Installation Instructions Provided by www.rearviewautomirrors.com These instructions have been prepared to provide you with details
More informationHORD INSTALLATION & SERVICE MANUAL. Hospital Operating Room Diffusers INSTALLATION & SERVICE MANUAL. Date: 06 / 12 Reference # : E-10 1
HORD Hospital Operating Room Diffusers Date: 06 / 12 Reference # : E-10 1 2 Table of Contents Prior to Installation... 4 Ductwork Layout... 4 Installation of HORD Air Curtain System...5-9 T-Bar Ceiling...5-6
More informationNORTHSTAR 154 BATH/SPA TV. Installation Instructions
NORTHSTAR 154 BATH/SPA TV Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Must be installed by a qualified electrician Read these instructions. Keep these instructions for future use. Install in
More informationVIRGINIA RAILWAY EXPRESS MANASSAS PARK STATION PARKING EXPANSION. Public Meeting June 20, 2017
MANASSAS PARK STATION PARKING EXPANSION Public Meeting June 20, 2017 1 AGENDA Project Status Schematic Design Circulation Traffic Analysis Proposed Garage Location Next Steps Cost Estimate 2 PROJECT PHASES
More informationINSTALLATION INSTRUCTIONS
OEM Recessed Lip Camera with Harness and OnStar Mirror for GM Vehicles with 10-pin Mirror Connector (Kit part number 9002-8722) Please read thoroughly before starting installation and check that kit contents
More informationChecker Unload Checkstand Installation Instructions
Front-End Checkouts Commercial Refrigeration Equipment Display Merchandisers Store Fixtures Checker Unload Checkstand Installation Instructions Attention Store Manager: Please find enclosed in this packet
More informationINSTALLATION INSTRUCTIONS
OEM Recessed Lip Camera with Harness and Slimline Mirror (Kit part number 9002-8724) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the
More informationPRE-DELIVERY GUIDE 2011
PRE-DELIVERY GUIDE 2011 How to make the delivery and installation of your new hot tub fast, easy, and trouble-free WATER THAT MOVES YOU Important Pre-Delivery Information Please read this booklet before
More informationChapter 4 Installation Guide
Chapter Installation Guide Danger 1. Turn off all power during installation of FBS-PLC or related equipments to prevent electric shock or damage to equipment.. Upon completion of all installation wiring,
More informationAutomated digital finishing systems for signs and displays. The Kongsberg i-xl-series
Automated digital finishing systems for signs and displays The Kongsberg i-xl-series Kongsberg i-xl Series: unmatched performance, versatility and durability Based on the Kongsberg XL-Series of short-run
More informationFOR SIT-STAND WORKSTATION
INSTALLATION MANUAL FOR SIT-STAND WORKSTATION Weight Capacity: 6.5-24.5 lbs. 6017180 Rev. B Contents Tools Required / Supplied Part Kits / Warnings/Disclaimers...2 Base Installation Clamp Mount Base Location...3
More informationVANGUARD Series 36" Slant Wall and Cone Direct Drive Fans Installation & Operator s Instruction Manual
VANGUARD Series 36" Slant Wall and Cone Direct Drive Fans Installation & Operator s Instruction Manual MV1600-1C 9/99 1625-003 2/2000 March 200 Chore-Time Warranty VANGUARD Series 36" Slant Wall and Cone
More informationCTFRP Series Power Supplies
CTFRP Series Power Supplies Ferroresonant Non-Standby Power Supplies User Manual Myers Power Products 6/2013 CTFRP Series Manual Chapter 1 General Information The Myers CTFRP Series Power Supply provides
More informationZoneEx Modular Wiring System
1 ZoneEx Modular Wiring System ZoneEx is an innovative modular wiring system which offers safer, easier, and efficient solution for electrical installation. The pre-assembled, plug & play Zone Boxes and
More informationHEMNES BUYING GUIDE. DESIGN Carina Bengs. CARE INSTRUCTION Wipe clean with a cloth dampened in a mild cleaner. Wipe dry with a clean cloth.
BUYING GUIDE HEMNES DESIGN Carina Bengs CARE INSTRUCTION Wipe clean with a cloth dampened in a mild cleaner. Wipe dry with a clean cloth. GOOD TO KNOW Be sure to follow the instructions in the manual for
More informationKIT No , and 80590
KIT No. 80531, 80545 and 80590 by MN-354 (05603) ECR 5593 Please read these instructions completely before proceeding with installation Air Spring Kit Parts List Item Description Quantity A Air Spring
More informationInstallation & Service Manual
MADE IN SWEDEN Friction Transporter Installation & Service Manual 203-04-2 TPE 00 Installation TPE 00 Manual Installation. TPE 00 should be mounted so the tray can move without obstruction in both directions.
More informationINSTALLATION INSTRUCTIONS
OEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 10-pin Mirror Connector (Kit part number 9002-8723) Items Included in the Kit: Bubble bag containing: Camera with Mount Mirror Mirror
More informationCURVED CC5 CC5 RF6 CC5 RF9 CC5 RF12 CC5 RF15 CC5 HT6 CC5 HT9 CC5 HT12. Page 1. Download C.A.D models or contact us on COSSIGA.COM
CURVED CC5 RF CC5 RF6 CC5 RF9 CC5 RF12 CC5 RF15 Deck forced refrigeration Sliding doors front and rear Double glazed Two adjustable shelves Ticket strips on shelves and deck Undershelf and canopy LED lights
More informationINFINITY MULTA SERIES
ASSEMBLY ASSEMBLY INSTRUCTIONS INSTRUCTIONS ASSEMBLY INSTRUCTIONS INFINITY MULTA SERIES Workstations, WORKSTATIONS, desks, DESKS, and AND tables TABLES with WITH powered POWERED ADJUSTMENT adjustment PARTS
More information12v LED In Rail Lighting Installation Guide
12v LED In Rail Lighting FairwayRailing.com 12v LED Connector Box wire From Transformer To next 12v LED Connector Box wire 1a. Install Transformer 1b. Run Wire 2. Install Connector Box 3. Wire Connector
More informationOVER THE RANGE MICROWAVE OVEN/HOOD SYSTEM INSTALLATION INSTRUCTIONS
OVER THE RANGE MICROWAVE OVEN/HOOD SYSTEM INSTALLATION INSTRUCTIONS Please read all instructions thoroughly before installing the Microwave Oven/Hood System. Two people are recommended to install this
More informationInstructions. for the installation of the KPC-MDT portion control kit
Instructions for the installation of the KPC-MDT portion control kit The kit can be used on either the MDT6N90, the MDT5N25, the MDT5N40, the MDT4F12 or the MDT3F12 ice maker dispensers. Kit Contents:
More informationAMBIT Collection PRICE LIST July 2008
AMBIT Collection PRICE LIST July 2008 Ambit Collection Suggested Layouts page 6 Desk shells page 17 Modular desk shells Credenzas page 28 Storage Units for C module shaped workstation page 40 Wall mount
More informationSeat Comfort Systems Ventilation/Heater Installation Instructions
Seat Comfort Systems Ventilation/Heater Installation Instructions KIT P/N: SCS00000C3 IMPORTANT: THE VENTILATION SYSTEM DRAWS AIR FROM THE CABIN AND MUST HAVE OPEN ACCESS THROUGH THE BOTTOM OF THE SEAT
More informationOEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 16-pin Mirror Connector (Kit part number )
OEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 16-pin Mirror Connector (Kit part number 9002-8722) Please read thoroughly before starting installation and check that kit contents
More informationCV41. Vehicle Mounting Kit. Reference Guide
CV41 Vehicle Mounting Kit Reference Guide CV41 Vehicle Mounting Kit Reference Guide........... 3 Secure the Smart Dock to a Vehicle.................... 3 Supply Power to the Smart Dock......................
More information