OPTEVA 923 IN LOBBY TELLER (ILT) PLAN mm (60") WIDE PLAN - STAND ALONE FRONT VIEW SIDE VIEW PAGE 1 OF 5 CALL NOTE:

Transcription

1 OPTEVA 9 IN LOBBY TELLER (ILT) mm ( ") U.L. SAFE L4 CALL CONSULT WITH DIEBOLD INSTALLATION/SERVICE BRANCH FOR ADDITIONAL DETAILS AND INFORMATION. PLEASE SEE PLANNING AND SITE PREPARATION GUIDE TP-8648-A. 77 SAFE (7 6 ") 6 ( 6 ") THE OPTEVA 9 IN-LOBBY TELLER (ILT) SOLUTION REQUIRES SEPARATE 9C (COMPANION), 9P (PARENT) COMPONENTS. SIDE PANELS, COUNTERTOP AND FILLER PANELS CAN BE ORDERED THROUGH DIEBOLD OR FABRICATED LOCALLY BASED UPON ILT APPLICATION - STAND ALONE VERSION OR 4mm WIDE VERSION (USED IN TELLER LINE) 9C (COMPANION) 9P (PARENT) 9C (COMPANION) 9P (PARENT) 77 SAFE (7 6 ") 6 ( 6 ") PAGE OF SUBJECT TO CHANGE W ITHOUT NOTICE" 4 6 ") ( ") POWER ENTRY OPENING SEE PAGE 4 OF FOR OPTIONAL FLOOR ENTRY 8 ") (4 8") 9P IS SET WITH BOTTOM m m ( ABOVE FLOOR. LEVELING LEGS ALLOW FOR ( (4 ( 4 ") (4 ( (") ") (4 ( 8 ") 6 ( 8 ") PLAN - STAND ALONE 6 4 ( 8 ") STAND ALONE (") UP TO AN ADDITIONAL mm (") LEVELING (") SEE PAGE OF FOR CONSUMER ACCESS DIMENSIONS ( 8") 4 (") OUTLINE OF COUNTERTOP 6 (6 8") PLAN - 4mm WIDE CUSTOMER PROVIDED COUNTERTOP MATERIAL MUST BE FIRE RETARDANT/RESISTANT TO MEET SAFETY AND REGULATORY REQUIREMENTS. OUTLINE OF SIDE PANELS 4 6 ") (4 FILE NO REV. 9C (COMPANION) ( 8 ") FRONT VIEW 9P (PARENT) ( 6 ") 699 (7 ") SAFE 7 (9 8") (4 SIDE VIEW

2 CONDUIT AND JUNCTION BOX REQUIREMENTS POWER REQUIREMENTS: THE ILT REQUIRES A SINGLE-PHASE, THREE-WIRE UNSWITCHED POWER RECEPTACLE. mm (") METAL CONDUIT FROM ALARM CONTROL CABINET JUNCTION BOX TO mm ( SQ. X 4mm ( 8") DEEP JUNCTIN BOX (ALL BY OWNER'S E.C.). WIRING TO THE RECEPTACLE MUST INCLUDE A THIRD-WIRE EARTH GROUND (CONDUIT GROUND IS NOT ACCEPTABLE). THE ILT WILL BE PROVIDED WITH THE POWER CORD. THE POWER SUPPLIED MUST BE AS SPECIFIED BELOW. CHOOSE AND SUPPLY THE PROPER POWER FOR THE SITE: OWNER'S E.C. TO RUN 9mm ( LIQUID TIGHT FLEX METAL CONDUIT OR 9mm ( RIGID CONDUIT FROM JUNCTION BOX TO CABLE CONNECTION PLATE. -7 VAC (+6%, -%) AT (±%) Hz, SINGLE-PHASE -7 VAC (+6%, -%) AT 6 (±%) Hz, SINGLE-PHASE -4 VAC (±%) AT (±%) Hz, SINGLE-PHASE -4 VAC (±%) AT 6 (±%) Hz, SINGLE-PHASE 9mm ( METAL CONDUIT AND UNSWITCHED ELECTRICAL SUPPLY TO mm ( SQ. X 4mm ( 8") DEEP JUNCTION BOX WITH RECEPTACLE WITHIN (87") OF SIDE CONNECTING PLATE. BOTTOM CONNECTION MUST BE COMPENSATED ACCORDINGLY (ALL BY OWNER'S E.C.) (SEE POWER REQUIREMENTS). POWER TO THE ILT IS TO BE A DEDICATED SERVICE AND MUST BE PROTECTED BY A SAFETY QUICK-DISCONNECT DEVICE TO BREAK LINE VOLTAGE (SUCH AS A CIRCUIT BREAKER AT THE ELECTRICAL SERVICE PANEL. THE QUICK-DISCONNECT DEVICE (OR CIRCUIT BREAKER) MUST TURN OFF THE LINE VOLTAGE AT THE FOLLOWING AMPERAGE. -7 VAC (+6%, -%) SERVICE, DISCONNECT AT AMPERES 4 OWNER'S E.C. TO SUPPLY -PRONG RECEPTACLE FOR PLUG-IN CONNECTOR SUPPLIED WITH UNIT. POWER CORD LENGTH mm (87") FROM SIDE OF UNIT. JUNCTION BOXES MUST BE LOCATED WITHIN mm (87") OF CONNECTING PLATE. (LENGTH OF ELECTRICAL POWER CABLE PROVIDED WITH UNIT). LOCATE IN AN EASILY ACCESSIBLE AREA. -4 VAC (±%) SERVICE, DISCONNECT AT AMPERES THE MODULE BULK POWER SUPPLY AND PROCESSOR POWER SUPPLY WILL PROVIDE POWER CONDITIONING TO PREVENT THE ILT FROM MALFUNCTIONING DUE TO SHORT-TERM AC POWER FLUCTUATIONS AS OUTLINED IN EN6-4-. CONFIGURATION: PROCESSOR, LCD CONSUMER DISPLAY, DIP CARD READER, RECEIPT PRINTER, IDM, ECRM AND COIN DISPENSER. POWER USAGE AND HEAT OUTPUT: POWER HEAT MACHINE STATUS USAGE OUTPUT IDLE (NO TRANSACTION) 9 WATTS 7 BTU RAPID PROCESSING 966 WATTS BTU TRANSACTION IN PROGRESS BOXES CAN BE FLUSH MOUNTED WITH CONCEALED CONDUIT FOR NEW CONSTRUCTION OR BOXES CAN BE SURFACE MOUNTED WITH OPERATING ENVIRONMENT (INTERIOR ONLY): EXPOSED CONDUIT FOR EXISTING CONSTRUCTION. SAFE LOCATION º C TO º C (º F TO 9º F) RELATIVE HUMIDITY (NON-CONDENSING) TO 8% AT º C (9º F), TO % AT º C (9º F) WEIGHT OF UNIT: 88kg (,94 LBS.) ELECTRICAL AND DATA CABLING ENTERS THE ILT THROUGH A CABLE ENTRY SIGNAL CABLE RUN CONSTRAINTS THE FOLLOWING CHART ITEMIZES THE PHYSICAL SPACING REQUIREMENTS OF THE SIGNAL CABLE RUN WITH RESPECT TO OTHER POWER AND ELECTRICAL EQUIPMENT CABLE RUN. SEPARATION FROM OTHER CABLES OPENING ON THE SIDE OF THE 9P. SEE SIDE VIEW ON PAGE OF. CABLES ENTERING THE ILT PASS THROUGH THE POWER CABLE PLATE WHICH IS ATTACHED TO THE INSIDE WALL OF THE 9P OVER THE CABLE ENTRY OPENING. THE CABLE ENTRY OPENING IS ON THE LEFT SIDE OF THE 9P AS VIEWED FROM THE BACK OF THE ILT 9P. TABS AS SHOWN CAN BE USED TO STRAIN RELIEVE OUTLINE OF CABLE ENTRY PLATE ON INSIDE OF 9P TYPE OF ELECTRICAL RUN FLUORESCENT, NEON OR INCANDESCENT LIGHTING FIXTURES BELOW KVA - KVA ABOVE KVA 7mm (") 7mm (") 7mm (") THE POWER AND DATA CABLES USING WIRE TIES 9mm ( 8") DIA. HOLE FOR ALARM CABLES (SIDE ENTRY) UNSHIELDED POWER LINE OR ELECTRICAL EQUIPMENT UNSHIELDED POWER LINES OR 7mm (") mm ('-") 6mm ('-") OPENING FOR POWER CORD AND DATA CABLES ELECTRICAL EQUIPMENT WITH SIGNAL CABLES ENCLOSED IN 64mm ( ") mm mm ('-") (SIDE ENTRY) GROUNDED CONDUIT POWER LINES IN GROUNDED CONDUIT WITH SIGNAL CABLES IN GROUNDED mm ( 6") 76mm (") mm CONDUIT SIGNAL CABLE INSTALLATION CONSTRAINTS: RELATIVE CARE IS REQUIRED WHEN INSTALLING SIGNAL CABLES IN CONDUITS, UNLIKE FILE NO REV. SUBJECT TO CHANGE W ITHOUT NOTICE" PAGE OF POWER AND LIGHTING CABLE, SIGNAL CABLES HAVE CONDUCTORS AND LIGHT INSULATION AND WILL NOT WITHSTAND AS MUCH STRAIN IN INSTALLATION. GROUND BOND STRAP TO BE FIELD INSTALLED ON INSIDE OF 9P AND ABOVE SAFE 4 AIR VENTS GROUND BOND STRAP TO BE FIELD INSTALLED ON INSIDE OF 9P 6 ( 6 ") AIR VENTS ( 8 ") 77 SAFE (7 6 ") REAR ELEVATION 4 (4 POWER AND DATA CABLE PLATE GROUND BOND STRAP FACTORY INSTALLED THIS SIDE ABOVE SAFE OPENING THRU SIDE WALL OF 9P SAFE 7 (9 8") (4 4 ") VERTICAL SECTION SEE SIDE VIEW ON PAGES AND OF 4 6 ") (7

3 OPTEVA 9 LOBBY TELLER (ILT) RECOMMENDED SERVICE AREAS CALL ") (8 (") 77 (7 6 ") 489 (8 8 ") ( 8 ") 6 ( 6 ") 9 6 ") (46 RECOMMENDED SERVICE AREA ALL ELECTRICAL AND DATA CABLES MUST ENTER UNIT IN THIS AREA WHEN SIDE ENTRY IS REQUIRED 4 ") (4 (") 6 ") (4 9 (9") 6 (4 ") SIDE VIEW FILE NO REV. SUBJECT TO CHANGE W ITHOUT NOTICE" PAGE OF 97 8 ") (8 4 ") (4 (") 77 (7 6") 489 (8 8") ( 8 ") 6 ( 6") PLAN RECOMMENDED SERVICE AREA - 4mm WIDE UNIT (") 9 6 ") (46 6 ") ( ILT TO BE SET AT EDGE OF ANY EXISTING COUNTERTOP AND MILL WORK, LEAVING THIS AREA FREE FOR ACCESS TO 9 ILT UNIT CLEAR AREA FOR ELECTRICAL AND DATA CABLES MUST BE PROVIDED THROUGH SIDE PANELS OR MILLWORK WHERE ELECTRICAL AND DATA CANNOT BE ROUTED UNDER 9 ILT UNIT

4 DETAIL FOR ANCHORING OPTEVA 9 IN LOBBY TELLER (ILT) TO FLOOR SAFE 89 4 ( 4 ") 8 ") 7 ( ") ( OPTIONAL POWER ENTRY UP THROUGH BUILDING FLOOR AND INTO UNIT THROUGH THIS 4mm ( 8") DIAMETER HOLE 7 6 ") (8 4 6 ") ( ") ( ") ( 9 4 ") (6 4 ( 6 ") 67 (4 6 ") 77 SAFE (7 6 ") 4 ( 6 ") 4 ( 6") ( ") 64 ( 6 ") 4 ( 8 ") 94 ( 6 ") 4 8 ") ( PLAN/SECTION - 9C (SAFE FLOOR) and 9P - (4).4mm (") DIA. FLOOR MOUNTING HOLES 9 - (4) 4mm ( 6") LEVELING LEG HOLES FILE NO REV. SUBJECT TO CHANGE W ITHOUT NOTICE" PAGE 4 OF NOTES: FOR ADDED SECURITY: IT IS RECOMMENDED THAT THE ILT SAFE BE SECURED TO THE FLOOR WITH ANCHOR BOLTS. USE THE FOLLOWING GUIDELINES TO DETERMINE THE APPROPRIATE METHOD FOR YOUR INSTALLATION. ANCHORING THE ILT TO CONCRETE FLOORS: IT IS RECOMMENDED THAT THE ILT BE ANCHORED TO CONCRETE FLOORS WHENEVER POSSIBLE. DIEBOLD RECOMMENDS USING A M OR 9mm ( ANCHOR BOLT THAT IS mm (8") LONG. CONCRETE FLOORS OR CONCRETE BASES MUST BE A MINIMUM OF mm( THICK FOR ANCHORING TO BE EFFECTIVE. THERE IS NO LIMIT FOR MAXIMUM THICKNESS. ANCHOR BOLTS MUST BE USED IN ALL AVAILABLE ANCHOR HOLES. IF THE TERMINAL IS EQUIPPED WITH LEGS, THE LEVELING LEGS MUST BE REMOVED BEFORE THE TERMINAL IS ANCHORED. REFER TO VIEW "A" AND "B" FOR ADDITIONAL DETAILS. ANCHORING THE ILT TO WOOD FLOORS: ILT INSTALLED ON WOOD FLOOR OR FLOORS SUPPORTED BY WOODED BEAMS CAN BE SECURED BY A MACHINE-THREADED NUT AND BOLT METHOD. IT IS PREFERRED THAT THE HARDWARE BE ATTACHED THROUGH SUPPORTING POSTS OR BEAMS FOR MAXIMUM HOLDING CAPACITY. ADDITIONALLY, THIS HARDWARE MUST ATTACH TO A LOCALLY FABRICATED REINFORCEMENT PLATE INSTALLED UNDERNEATH THE FLOOR TO PROVIDE ADDITIONAL STRENGTH. THE REINFORCEMENT PLATE IS TYPICALLY 6mm ( THICK. IT IS IMPORTANT TO NOTE THAT THE OVERALL HOLDING CAPACITY OF A WOOD FLOOR WILL BE LESS THAN THAT OF CONCRETE FLOORS. ANCHORING THE ILT TO STEEL FLOORS: ILT INSTALLED ON STEEL FLOORS CAN BE SECURED BY A MACHINE-THREADED METHOD. IT IS PREFERABLE THAT THE HARDWARE BE ATTACHED THROUGH SUPPORTING POSTS OR BEAMS FOR MAXIMUM HOLDING CAPACITY. ADDITIONALLY, THIS HARDWARE MUST ATTACH TO A LOCALLY FABRICATED REINFORCEMENT PLATE INSTALLED UNDERNEATH THE FLOOR TO PROVIDE ADDITIONAL STRENGTH. THE COMBINED BACKING PLATE AND FLOOR THICKNESS MUST BE AT LEAST mm ( "). OWNER'S INSTALLER TO DRILL (4) 9mm ( DIA. X mm (8" MIN.) DEEP HOLES IN CONCRETE FLOOR (RECOMMENDED DRILLING COMPLETELY THROUGH FLOOR WHEN POSSIBLE AND TO BE SECURED TO THE CONCRETE FLOOR WITH (4) 9mm ( - X mm (8") LONG WEDGE ANCHORS (SUPPLIED BY OWNER'S INSTALLER) DIEBOLD PART NUMBER A, HILTI PART NUMBER 8). VIEW "A" MINIMUM HOLE DEPTH mm (8") MIN. (8") VIEW "B" MINIMUM CONCRETE DEPTH mm ( ( MIN.

5 OPTEVA 9 IN LOBBY TELLER (ILT) L4 CALL mm ( ") U.L. SAFE CONSUMER ACCESS DIMENSIONS HEIGHT DEPTH A TOP OF TOUCH SCREEN 6mm ( 8") 7mm (6 B BOTTOM OF TOUCH SCREEN mm ( mm ( ") C D E F G H I J TELLER CALL BUTTON HEAD PHONE JACK ECRM OPTIONAL SIGNATURE PAD KEY PAD OPTIONAL CONTACTLESS CARD READER OPTIONAL D BAR CODE SCANNER DIP READER 8mm (9 8") 97mm (6 ") 86mm ( 7mm (9 8") 98mm (8 8") 94mm (7") 869mm (4 6") 884mm (4 9mm ( 6") -9mm ( 4mm ( 6") mm (") -4mm ( 6") K OPTIONAL COIN DISPENSER 4mm (") PAGE OF SUBJECT TO CHANGE W ITHOUT NOTICE" A B C D L TOP OF TOUCH SCREEN BOTTOM OF TOUCH SCREEN TELLER CALL BUTTON HEAD PHONE JACK E ECRM DEPTH DIMENSIONS FROM THIS FRONT SURFACE M IDMBD RECEIPT PRINTER HEIGHT - FROM BOTTOM OF SAFE DEPTH - FROM FRONT SURFACE SHOWN IN VIEWS BELOW DEPTH DIMENSIONS FROM THIS SURFACE 79mm (9 8") 8mm ( 6") OPTEVA 9 IN LOBBY TELLER FRONT VIEW DEPTH DIMENSION SHOWN FOR ECRM AND DIP READER IS THE DISTANCE EACH EXTENDS OUT FROM FRONT SURFACE OPTIONAL SIGNATURE PAD KEY PAD OPTIONAL CONTACTLESS CARD READER OPTIONAL D BAR CODE SCANNER DIP READER OPTIONAL COIN DISPENSER IDMBD RECEIPT PRINTER F G H I J K L M FILE NO REV. OPTEVA 9 IN LOBBY TELLER SIDE VIEW