Detection System Model 8800 Series

Transcription

1 Detection System Model 8800 Series rchitect/contractor Information Package 3M Library Systems 3M Center, Building 225-4N-14 St. Paul, Minnesota _B Copyright 2006, 3M. ll rights reserved.

2 3M Library Systems 3M Center, Building 225-4N-14 St. Paul, MN Telephone Fax Dear rchitect/contractor: I would like to take this opportunity to thank you for your interest in the 3M Library Systems products. I think you will find all of the information you will need to assist in the implementation of your plan. 3M LIBRRY SYSTEMS IS LEDING SUPPLIER OF LIBRRY DETECTION, SELF SERVICE, ND PRODUCTIVITY SOLUTIONS. S PRT OF OUR OFFERING, 3M FCILITTES THE INSTLLTION ND FTER-SLE SUPPORT (EITHER DURING WRRNTY OR BY SERVICE GREEMENT WITH THE PURCHSE). 3M SHLL COMPLY WITH LL PPLICBLE FEDERL, STTE ND LOCL LWS ND REGULTIONS PPLICBLE TO PRODUCT SUPPLIERS LIKE 3M. BECUSE 3M IS NOT SUBCONTRCTOR, WE WILL NOT CCEPT HOLDBCKS, OR OTHER PYMENT RESERVTIONS. 3M S SLES RE EXPRESSLY MDE CONDITIONL UPON THE CONTRCTOR S GREEMENT TO MKE PYMENT IN FULL WITHIN THIRTY (30) DYS FTER DTE OF SHIPMENT. IF THE PURCHSE IS TO BE TX EXEMPT, CERTIFICTE MUST BE FORWRDED TO 3M FOR THE FILE. For service and installation, order status, or any additional questions, please feel free to contact 3M at Sincerely, Gregory P. Pfouts National Sales Manager 3M Library Systems B

3 Preinstallation Worksheet 3M Detection Systems Please complete this form and fax it to 3M at Today s date Sales consultant ccount name Key contact name Phone No. Installation location Install contact name Phone No. Installation date Purchasing/payment contact Phone No. Select a mounting option: Direct Mount Base Plate Buried Cable 3500/3800/ /3800/ /3800/8800 Minimum distance to protected books: 3 ft. System model number(s) ccessories Delayed warranty start date (if applicable) Model/serial number of equipment to be replaced/removed 3M dismantle at additional current rates... Customer dismantle and removal... Preinstallation worksheet reviewer Note: It is the customer s responsibility to move the system within 10 ft. of the installation location before scheduling the installation. Does account require PO number for payment of invoices? Yes No Minimum distance to steel-stud wall: in. [457 mm] ft in. [76,2 mm] Minimum distance to door frame 4 ft. [1,22 m] to comply with D Minimum distance to large metal objects: in. [457 mm] ft in. [15,24 cm] Your site layout must meet the following requirements to help ensure optimal performance: Minimum distance from system to large metal objects (windows, doors, walls, display cases, shelves, cabinets, picture frames, counter edges, waste baskets, and furniture): in. [45,7 cm] ft. [91,4 cm] in. [15,24 cm] Minimum distance from system to CRT: 3500/ ft. [2,13 m] in. [7,6 cm] The Model 3500 electronics enclosure must be a minimum of 4 ft. [1,22 m] min./21 ft. [6,4 m] (wire-run distance) max. from system panels, and within 10 ft. [3,05 m] of the power source. The system must be at least 5 ft. [1,52 m] from copiers (3 in. [76,2 mm] for the Model 8800). The system must be at least 3 ft. from materials containing security markers. The system must be at least 4 ft. [1,22 m] from door frames to meet D requirements. The system must be within 10 ft.* [3,05 m] of the power source (9.84 ft.* 3,0 m for Model 8800). * Wire-run distance, not straight-line distance inch I.D. non-metallic conduit for buried-cable systems. See the rchitect/contractor Information Package for system dimensions and requirements. 3M Library Systems 3M Center, Bldg N-14 St. Paul, Minnesota Minimum distance to CRT: ft. [2,13 m] ft. [2,44 m] in. [76,2 mm] Maximum distance to power outlet: Note: The concrete thickness under 3500/ ft. [3,05m] the mounting feet must be a minimum ft. [3,0 m] of 3.5 in. [89 mm]. Minimum distance to copy machine 5 ft. [1,52 m] (3500/3800 only) Draw your system layout in the following grid: 1 square = 1 ft. (30.5 cm) Doors Printed in U.S.. Copyright M. ll rights reserved , 060-, Rev. G

4 rchitect/contractor Information Package 3M Detection System Model 8800 Series This package provides architects and contractors with information required to install a 3M Detection System. This information must be followed to help ensure optimal performance. Topic Page rchitect/contractor Information Package M Detection System Model 8800 Series... 1 The 10 Most Important Points for a Successful Installation... 2 System Design Considerations... 3 Patron Traffic Patterns...3 System Location...3 System Layout Specifications... 4 System Placement Relative to Interfering Objects... 5 Installation Specifications... 6 Installation Requirements...6 Dimensions...7 Power Requirements...8 Wiring Requirements...8 pproximate Weights...9 Contractor Instructions for Buried Power Installations Before You Begin...10 Materials Required...10 Installation Procedure Buried Power...11 Contractor Instructions for Buried Cable/Conduit Installations Before You Begin...12 Related Information...12 Materials Required...12 Installation Procedure with Buried Cables...13 One-Corridor Detection System Layout Plan Buried Power and Wiring...14 Two-Corridor Detection System Layout Plan Buried Power and Wiring...15 Three-Corridor Detection System Layout Plan Buried Power and Wiring...16 Four-Corridor Detection System Layout Plan Buried Power and Wiring...17 Five-Corridor Detection System Layout Plan Buried Power and Wiring...18 Warranty

5 The 10 Most Important Points for a Successful Installation 1 Provide a minimum distance of 3 in. [76.2 mm] between the detection system and any wall. 2 Provide a minimum distance of 6 in. [15.24 cm] between detection panels and large metal objects, which may include: large metal shelves, refrigerators, heavy support beams, safes, heating/air conditioning ductwork, etc. 3 Provide a 4-foot [1.2 m] clear space between the detection system panels and any door. This is required for D (mericans with Disabilities ct) compliance. 4 Plan the system layout so that the corridor(s) are centered on the door(s). 5 Locate the system to allow good observation/supervision of the system by your circulationdesk staff. 6 Plan the system layout so that patrons entering and exiting the library do not interfere with each other. void two-way traffic in a single corridor. 7 Locate the system so that books and other secured items are stored at least [91.4 cm] from the detection system. This helps ensure that secured items within the library are not detected by the system. 8 Locate the system so that patrons and book carts with secured items cannot pass within 36 in. [91.4 cm] of the detection system. This helps ensure that secured items within the library are not detected by the system. 9 Provide an electrical outlet within 9.84-feet [3.0 m] of the systems power panel. This distance is measured in wire-run feet, not straight-line distance. 10 For buried-cable installations, use 1.25 in.[31.75 mm] I.D., conduit with correct spacing. This size conduit is required to accommodate connectors on the ends of the interconnecting cables _B

6 System Design Considerations The following design considerations should be addressed when planning the layout of any 3M Detection System. Patron Traffic Patterns 1 Does your system layout plan center the corridor(s) on the door(s) and help establish normal traffic patterns? 2 Do patrons have an easy exit path? Keep changes in traffic direction between check-out and exit to an absolute minimum. 2 Will patrons entering and exiting the library interfere with each other? void two-way traffic in a single corridor. 3 In the event of an alarm, is there room to identify or stop patrons before they leave the library? 4 re there enough detection-system corridors available to handle typical amount of traffic and to meet codes? 5 While in the library, will patrons stand directly next to the system or carry secured items within [91.4 cm] of the system? This may cause false alarms. 6 Will your book carts fit through the corridor? System Location 1 Do check-out personnel have good visibility and access to the detection hardware? 2 re all applicable codes met? 3 Have you investigated whether there are large metal objects hidden within the walls? 4 Is power located to minimize the need to run cords and wire molding through traffic areas? 5 Will book carts with secured items be stored near the detection system? To avoid false alarms, all secured items must be kept at least [91.4 cm] from the detection system at all times _B

7 System Layout Specifications These specifications define the environment required to successfully install a Detection System Model 8800 Series. Compliance with these requirements will help ensure that the detection system performs as designed. ny compromising of these requirements may result in reduced effectiveness of your 3M Detection System. lways follow applicable federal, state, and local codes when planning and completing installation of this equipment. The 3M Detection System Model 8800 Series is a one- to five-corridor detection system consisting of panels that can be mounted to a base plate or directly to the floor. Power wiring and panel-to-panel wiring can be routed on the surface in UL-listed wire mold or buried under the finished floor in an approved conduit. 1-Corridor with Base Plate ~ The detection system s corridor width is [91.4 cm] to comply with the D (mericans with Disabilities ct). The electronics for the system are enclosed in one of the panels. 2-Corridors with Wire Mold ~ vailable colors include: Dark gray (Pantone Cool Gray 11C) or Light gray (Pantone Cool Gray 5C) n alarm light is located on top of one panel and an audible alarm is located on top of the other panel. 3-Corridors with Base Plate ~ ~ ~ 4-Corridors with Base Plate ~ ~ 5-Corridors with Wire Mold ~ 8800_CP_ _B

8 System Placement Relative to Interfering Objects Doors (metal framed) Exit control hardware The system may be located as close as 3 in. [76.2 mm] from a metal-framed door. D (mericans with Disabilities ct) requires a 4-foot [1.2 m] clear space between the detection system and exit doors to help ensure wheelchair-maneuvering space. The first post for an exit-control system can be no closer than 3 in. [76.2 mm] in one of the locations specified in Figure 1. Metal railings surrounding the system using two or more horizontal members must be a minimum of 3 in. [76.2 mm] from a detection panel. 8800_CP_005 Figure 1: Post placement for an exit-control system. Large metal objects (LMO) Counters with metal frames Windows (metal framed) Walls (steel stud) Book carts Protected material Large metal objects are not allowed within 6 in. [15.24 cm] of a detection panel. Examples include: large metal shelves, refrigerators, heavy support beams, safes, heating/air conditioning ductwork. Counters that have a metal frame that forms a continuous, electrically conductive, loop should not be located within 3 in. [76.2 mm] of a detection panel. For optimum performance, a Detection System Model 8800 Series should be placed at least 3 in. [76.2 mm] from a metal-framed window. Walls with steel studs are not allowed within 3 in. [76.2 mm] of the closest detection panel. Plan the layout so that there is not an obvious location for customers to leave empty book carts within 3 in. [76.2 mm] of detection panels. Books and other protected articles should be at least [91.4 cm] from the closest point of the security system. (This helps ensure that secured items within the library are not detected by the system.) Plan the layout so that patrons will not congregate or wait in line within [91.4 cm] of a detection panel. Stereo components Distance between systems FM stereo receivers placed within 10 feet [3.0 m] of the detection panels may experience some interference. Compact disc players are not affected by the Detection System Model 8800 Series.. The minimum distance between detection systems is [91.4 cm] _B

9 Installation Specifications Installation Requirements 3M Detection System Model 8800 Series can be mounted to a base plate or directly to the floor. Power wiring and panel-to-panel wiring can be routed on the surface in UL-listed wire mold or buried under the finished floor in an approved conduit. The detection system s corridor width is [91.4 cm], to comply with the D (mericans with Disabilities ct). The electronics for the system are enclosed in one of the panels. vailable colors include: Dark gray (Pantone Cool Gray 11C) or Light gray (Pantone Cool Gray 5C) n alarm light is located on top of one panel and an audible alarm is located on top of the other panel. Walls that do NOT contain large metal objects Minimum Service Clearance between an outside panel and walls that do not contain large metal objects 3.0 in. [76.2 mm] Wall Mounting surface Concrete thickness concrete in the area under the mounting feet must be a minimum of 3.5 in. [89 mm] thick for anchoring. Leveling the floor in the area of the mounting feet must be flat, level, high-quality concrete. Mounting feet - the contractor must avoid placing conduit or reinforcing rods in the anchor area of the mounting feet. Minimum clearances The system must be installed with the following minimum clearances between the panels and surrounding walls or objects. Walls with no large metal objects Detection panels must be at least 3 in. [76.2 mm] from walls that do not contain large metal objects. Walls with large metal objects Detection panels must be at least 6 in. [15.24 cm] from large metal objects (for example: large metal shelves, refrigerators, heavy support beams, safes, heating/air conditioning ductwork). Walls that contain large metal objects Minimum Clearance Between an outside panel and walls that contain large metal objects 6.0 in. [15.24 cm] Wall 8800_CP_004 Figure 2: Minimum Clearance from Walls _B

10 Dimensions Front View 70 in. [1.78 m] 1-Corridor System * 41 in. [1.04 m.] 2-Corridor System 79.5 in. [2.01 m.] * 3-Corridor System 118 in. [3 m.] * 4-Corridor System * 5-Corridor System * 195 in. [4.95 m.] Side View 8800_CP_ in. [660 mm] Figure 3: Dimensions *To determine the total space required, add the following: 3 inches [76.2 mm] of clearance between each outside panel and walls without large metal objects or 6 inches of clearance [15.24 cm] between each outside panel and walls with large metal objects _B

11 Power Requirements The 3M Detection System Model 8800 Series is a computer-based device that requires high-quality, surge-free, and noise-free electrical power for optimum performance. Voltage Requirement The system is designed for worldwide use and includes a universal power supply that operates with the following voltages: 100 to 240 VC, single phase, 50 or 60 Hz. Recommendations 15 dedicated circuit. Maximum RMS current draw 100/120 VC: /240 VC: 0.25 Power cord Electrical outlet 18 gage, 3-wire, S-rating, 9.84 feet [3.0 m] long, NEM 5-15P plug, with an IEC 320 connector. Customer must supply an electrical outlet within the power-cord length. For 3-, 4-, and 5-corridor systems, two electrical outlets are required. dedicated circuit is not required but is recommended to prevent overloading and loss of security. Circuit loading must not exceed 50% of the rated circuit current to help ensure voltage stability. Wiring Requirements The entire system can be rotated 180 to reverse the power-entry location. Panel-to-panel wiring Power wiring Surface Wiring Wires are enclosed in a wire mold and covered by a threshold. No customer construction is required. Each power cord is enclosed in Wiremold Pancake 2600 Series Surface Raceway and enters the system through the side of the panel. No customer construction is required. Under-floor Wiring Wires are enclosed in 1.25 inch [31.8 mm] I.D. conduit that enters the system through the mounting foot. See Installation Procedure with Buried Cables on page 13. floor-mounted electrical box is installed approximately 3 in. [76.2 mm] from the panel. The electrical box provides termination for the system power cord(s). See Contractor Instructions for Buried Power Installations on page _B

12 pproximate Weights # of Corridors 3M Detection System Weight 1 Model 8801 Floor Mounted (with wire mold) 110 lb. [49.9 Kg] 1 Model 8801 Baseplate Mounted 135 lb. [61.2 Kg] 1 Model 8801 Floor Mounted (with buried cables) 110 lb. [49.9 Kg] 2 Model 8802 Floor Mounted (with wire mold) 170 lb. [77.1 Kg] 2 Model 8802 Baseplate Mounted 200 lb. [90.7 Kg] 2 Model 8802 Floor Mounted (with buried cables) 165 lb. [74.8 Kg] 3 Model 8801 (x2) Floor Mounted (with wire mold) 230 lb. [104.3 Kg] 3 Model 8801 (x2) Baseplate Mounted 290 lb. [131.5 Kg] 3 Model 8801 (x2) Floor Mounted (with buried cables) 220 lb. [99.8 Kg] 4 Model 8801/8802 Floor Mounted (with wire mold) 340 lb. [154.2 Kg] 4 Model 8801/8802 Baseplate Mounted 420 lb. [190.5 Kg] 4 Model 8801/8802 Floor Mounted (with buried cables) 330 lb. [149.7 Kg] 5 Model 8802 (x2) Floor Mounted (with wire mold) 380 lb. [172.4 Kg] 5 Model 8802 (x2) Baseplate Mounted 540 lb. [245 Kg] 5 Model 8802 (x2) Floor Mounted (with buried cables) 440 lb. [200 Kg] _B

13 Contractor Instructions for Buried Power Installations Before You Begin 1 Read all installation instructions before starting this installation procedure. 2 Before beginning any work, the contractor must call 3M at (U.S. only) or your local 3M Service Representative (outside the U.S.) to request a Preinstallation Technician Site Visit. Before attempting any work, a 3M technician must visit the site and verify that the environment and location are acceptable. System setup and testing may be required to verify the location is acceptable. If there are any questions, contact 3M Library Systems Technical Service at (U.S. only) or call your local 3M Service Representative (outside the U.S.). Materials Required Item Steel floor box(es), conduit, and associated wiring Floor box cover plate(s), gasket, and carpet ring (if needed) C power cord (part of detection system) Device to cut trench in floor Material to fill in around and cover conduit after trench is cut Supplier Electrical Contractor Electrical Contractor 3M Contractor Contractor 8800_CP_ _B

14 Installation Procedure Buried Power If necessary, request assistance from a 3M Service Technician before positioning floor box. Contractor responsibilities 1 The contractor will install a steel floor box. Position the box per Figure 4. Floor boxes are typically 5 in. x 5 in. [127 mm x 127 mm], with a 4-inch [102 mm] cover flange. Some floor boxes include "prepour" and "after-pour" level adjustments. Panel Mounting Foot Panel-to-panel Conduit Panel System Power Cord 90-degree Cord Fitting 0.5 in. [12.7 mm] NPT Cover Plate 0.5 in. [12.7 mm] NPS Plug Size The floor box cannot be located under the detection system. (It must be off to the side of the panel.) Steel Floor Box (with leveling screws) Conduit 0.5 in. [12.7 mm] 2 The contractor will complete wiring from the floor box to a mp circuit (preferably dedicated for the security system). 26 in. [66 cm] Top View 3 fter system installation, the contractor will: Terminate the detection system power cord to the circuit wires in the floor box. Install gasket, cover plate, and carpet ring if required. Minimum 41 in. [1.04 m] Floor Box (hardwired to power cord) 3M Installer Responsibilities 1 The 3M installer will install the detection system panels and floor anchors, and route the panel-to-panel wiring. Panel 3 in. [76.2 mm] 1 3 in. [76.2 mm] Position the floor box within 3 inches on either side of the power entry point [1] 2 The 3M installer will energize the detection system and will complete operational checks and adjustments. System Power Cord 7.5 in. [191 mm] 8800_CP_006 Figure 4: Electrical floor box installation _B

15 Contractor Instructions for Buried Cable/Conduit Installations Before You Begin 1 Read all installation instructions before starting this installation procedure. 2 Before beginning any work, the contractor must call 3M at (U.S. only) or your local 3M Service Representative (outside the U.S.) to request a Pre-installation Technician Site Visit. Before attempting any work, a 3M technician must visit the site and verify that the environment and location are acceptable. System setup and testing may be required to verify that the location is acceptable. If there are any questions, contact 3M Library Systems Technical Service at (U.S. only) or call your local 3M Service Representative (outside the U.S.). Related Information If C power wiring is also buried, see Contractor Instructions for Buried Power Installations on page 10. Materials Required Item 3M Detection System Model 8800 Series mounting hardware Optional - Single-corridor Extended Cable Kit (PN ) that allows you to bury the conduit at a depth of [91.4 cm] Supplier 3M 3M One kit is required for one-corridor systems Two kits are required for two- and three-corridor systems Three kits are required for four-corridor systems Four kits are required for five corridor systems Rigid metallic or plastic conduit, 1.25 inch [31.7 mm] I.D. Concrete as required to pour floor Device to cut trench in floor (for existing construction) Materials to hold conduit in position while pouring floor Finish flooring Contractor Contractor Contractor Contractor Contractor _B

16 Installation Procedure with Buried Cables These instructions will be used by 3M installers and the contractor to ensure proper installation of Detection System with buried cables. Procedure 1 The contractor will position and install the panel-to-panel conduit and C power conduit for each system. The floor box for C power must be located on the side of the system where power is connected. See Installation Procedure Buried Power on page The contractor will complete the sub floor and finished floor in the installation area. 3 t, during, or after system installation, the contactor will complete the C power wiring for the system(s). Complete wiring from the floor box to a mp circuit (preferably dedicated for the security system). Terminate the system power cord to the electrical supply circuit in the floor box. 4 The 3M installer will install the system panels and floor anchors, and route the panel-to-panel wiring through the contractor-installed conduit. Installation Notes Panel-to-panel conduit requirements Conduit size panel-to-panel conduit must have a minimum I.D. of 1.25 in. [31.75 mm] to accept cable connectors. If this conduit has an I.D. of less than 1.25 inch [31.75 mm] there will be an additional charge at installation. Maximum depth the standard maximum depth of conduit is 18 in. [457 mm] due to the length of panel-to-panel cables. If you want to bury the conduit at a depth of [91.4 cm], you must purchase Extended Cable Kits (PN ). Conduit bends each conduit bend radius must be typical to the electrical industry. Water-type 90 o bends or fittings are not acceptable. bove-floor height panel-to-panel conduit must not extend more than 0.5 in. [12.7 mm] above the finished floor. Floor requirements Concrete thickness the concrete in the area under the mounting feet must be a minimum of 3.5 inches [89 mm] thick for anchoring. Leveling the floor in area of mounting feet must be flat, level, high-quality concrete. Mounting feet the contractor must avoid placing conduit or reinforcing rods in the anchor area of the mounting feet. Existing floors existing floors must be core drilled or trenched to accept buried conduits. Keep the trench width to a minimum to avoid weakening the concrete in the anchor area. 5 The 3M installer will energize the system and complete operational checks and adjustments _B

17 One-Corridor Detection System Layout Plan Buried Power and Wiring 3M Library Systems 3m Center Bldg N- 14 St Paul, MN One Corridor Notes 1 Power source can be from either side of the system. 2 Power cord length is 9.84 ft. [3 m]. 3 If underground power is required, use a flush-mount floor box and terminate the power cord in the floor box after the system is installed. (See Contractor Instructions for Buried Power Installations on page 10.) 4 Minimum floor thickness: 3.5 in. [89 mm]. 5 Floor must be level and flat in the area under each panel s mounting foot. 6 Conduit and reinforcing rod must not be located in anchor hole area under mounting feet. 7 Standard cable set supplied for buried wiring is adequate for conduit buried a maximum depth of 18 in. [457 mm] inch corridor complies with D Guidelines. 9 Important! See System Placement Relative to Interfering Objects on page 5 for minimum distances to interfering objects. 8800_CP_036_1_Corr Max bove-floor Conduit Height 0.25 in. [6.35 mm] for plastic 0.5 in. [12.7 mm] for metal Conduit bend radius to be typical of Electrical Industry Standards nchor Holes (4 per mounting foot) 3M Installed 6.25 in. [159 mm] Section - 18 in. [457 mm] max.(typical) Rigid, metal or plastic conduit 1.25 in. [31.75 mm] I.D in. [978 mm] in. [260 mm] Panel-to-panel Wire Inlet 1 in. x 3 in. [25.4 mm x 76 mm] Electrical Supply Box min. 26 in. [660 mm] Mounting Foot 5 ft. [1.5 m] min. (system centerline to door) Mounting Foot Outline 41 in. [1.04 m] Electrical Supply Box Hardwired to power cord. 2.5 inch (min) clearance from center of mounting foot. 8800_CP_ _B

18 Two-Corridor Detection System Layout Plan Buried Power and Wiring 3M Library Systems 3m Center Bldg N-14 St Paul, MN Two-Corridor 8800_CP_037_2_Corr Notes 1 Power source can be from either side of the system. 2 Power cord length is 9.84 ft. [3 m]. 3 If underground power is required, use a flush-mount floor box and terminate the power cord in the floor box after the system is installed. (See Contractor Instructions for Buried Power Installations on page 10.) 4 Minimum floor thickness: 3.5 in. [89 mm]. 5 Floor must be level and flat in the area under each panel s mounting foot. 6 Conduit and reinforcing rod must not be located in anchor hole area under mounting feet. 7 Standard cable set supplied for buried wiring is adequate for conduit buried a maximum depth of 18 in. [457 mm] inch corridor complies with D Guidelines. 9 Important! See System Placement Relative to Interfering Objects on page 5 for minimum distances to interfering objects. Section - Conduit bend radius to be typical of Electrical Industry Standards 18 in. [457 mm] max.(typical) nchor Holes (4 per mounting foot) 3M Installed in in. [260 mm] [159 mm] Max bove-floor Conduit Height 0.25 in. [6.35 mm] for metal 0.5 in. [12.7 mm] for plastic. Rigid, metal or plastic conduit 1.25 in. [31.75 mm] I.D in. [978 mm] (Typical) (Typica)l Panel-to-panel Wire Inlet 1 in. x 3 in. [25.4 mm x 76 mm] Electrical Supply Box 26 in. [660 mm] Mounting Foot 5 ft. [1.5 m] min. (system centerline to door) Mounting Foot Outline Electrical Supply Box Hardwired to power cord. 2.5 inch (min) clearance from center of mounting foot. 41 in. [1.04 m] (Typical) min. 8800_CP_ _B

19 Three-Corridor Detection System Layout Plan Buried Power and Wiring 3M Library Systems 3m Center Bldg N-14 St Paul, MN _CP_035_3_Corr Notes 1 Power source can be from either side of the system. 2 Power cord length is 9.84 ft. [3 m]. 3 If underground power is required, use a flush-mount floor box and terminate the power cord in the floor box after the system is installed. (See Contractor Instructions for Buried Power Installations on page 10.) 4 Minimum floor thickness: 3.5 in. [89 mm]. 5 Floor must be level and flat in the area under each panel s mounting foot. 6 Conduit and reinforcing rod must not be located in anchor hole area under mounting feet. 7 Standard cable set supplied for buried wiring is adequate for conduit buried a maximum depth of 18 in. [457 mm] inch corridor complies with D Guidelines. 9 Important! See System Placement Relative to Interfering Objects on page 5 for minimum distances to interfering objects. Section - 18 in. [457 mm] max.(typical) min. Electrical Supply Box Hardwired to power cord. 2.5 inch (min) clearance from center of mounting foot. Electrical Supply Box Conduit bend radius to be typical of Electrical Industry Standards nchor Holes (4 per mounting foot) 3M Installed Panel-to-panel Wire Inlet 1 in. x 3 in. [25.4 mm x 76 mm] Max above-floor Conduit Height 0.25 in. [6.35 mm] for metal 0.5 in. [12.7 mm] for plastic in in. [260 mm] [159 mm] Rigid, metal or plastic conduit 1.25 in. [31.75 mm] I.D in. [978 mm] (Typical) (Typica)l Electrical Supply Box 26 in. [660 mm] 5 ft. [1.5 m] min. (system centerline to door) Mounting Foot Outline Mounting Foot Electrical Supply Box Hardwired to power cord. 2.5 inch (min) clearance from center of mounting foot. 41 in. [1.04 m] (Typical) min. 8800_CP_ _B

20 Four-Corridor Detection System Layout Plan Buried Power and Wiring 3M Library Systems 3m Center Bldg N-14 St Paul, MN _CP_038_4_Corr Notes 1 Power source can be from either side of the system. 2 Power cord length is 9.84 ft. [3 m]. 3 If underground power is required, use a flush-mount floor box and terminate the power cord in the floor box after the system is installed. (See Contractor Instructions for Buried Power Installations on page 10.) 4 Minimum floor thickness: 3.5 in. [89 mm]. 5 Floor must be level and flat in the area under each panel s mounting foot. 6 Conduit and reinforcing rod must not be located in anchor hole area under mounting feet. 7 Standard cable set supplied for buried wiring is adequate for conduit buried a maximum depth of 18 in. [457 mm] inch corridor complies with D Guidelines. 9 Important! See System Placement Relative to Interfering Objects on page 5 for minimum distances to interfering objects. Section - Section - min. Electrical Supply Box Hardwired to power cord. 2.5 inch (min) clearance from center of mounting foot. Electrical Supply Box Conduit bend radius to be typical of Electrical Industry Standards nchor Holes (4 per mounting foot) 3M Installed Max bove-floor Conduit Height 0.25 in. [6.35 mm] for metal 0.5 in. [12.7 mm] for plastic in in. [260 mm] [159 mm] 18 in. [457 mm] max.(typical) Rigid, metal or plastic conduit 1.25 in. [31.75 mm] I.D in. [978 mm] (Typical) (Typica)l Panel-to-panel Wire Inlet 1 in. x 3 in. [25.4 mm x 76 mm] Electrical Supply Box 26 in. [660 mm] 5 ft. [1.5 m] min. (system centerline to door) Mounting Foot Outline 79.5 in. [202 cm] Mounting Foot Electrical Supply Box Hardwired to power cord. 2.5 inch (min) clearance from center of mounting foot. 41 in. [1.04 m] (Typical) min. 8800_CP_ _B

21 Five-Corridor Detection System Layout Plan Buried Power and Wiring 3M Library Systems 3m Center Bldg N-14 St Paul, MN Notes 1 Power source can be from either side of the system. 2 Power cord length is 9.84 ft. [3 m]. 3 If underground power is required, use a flush-mount floor box and terminate the power cord in the floor box after the system is installed. (See Contractor Instructions for Buried Power Installations on page 10) 4 Minimum floor thickness: 3.5 in. [89 mm]. 5 Floor must be level and flat in the area under each panel s mounting foot. 6 Conduit and reinforcing rod must not be located in anchor hole area under mounting feet. 7 Standard cable set supplied for buried wiring is adequate for conduit buried a maximum depth of 18 in. [457 mm] inch corridor complies with D Guidelines. 9 Important! See System Placement Relative to Interfering Objects on page 5 for minimum distances to interfering objects. Section - Section - Conduit bend radius to be typical of Electrical Industry Standards 18 in. [457 mm] max.(typical) Electrical Supply Box min. Electrical Supply Box Hardwired to power cord. 2.5 inch (min) clearance from center of mounting foot. Conduit bend radius to be typical of Electrical Industry Standards nchor Holes (4 per mounting foot) 3M Installed nchor Holes (4 per mounting foot) 3M Installed in in. [260 mm] [159 mm] Max bove-floor Conduit Height 0.25 in. [6.35 mm] for metal. 0.5 in. [12.7 mm] for plastic Rigid, metal or plastic conduit 1.25 in. [31.75 mm] I.D in. [978 mm] (Typical) (Typica)l Panel-to-panel Wire Inlet 1 in. x 3 in. [25.4 mm x 76 mm] Electrical Supply Box 26 in. [660 mm] 5 ft. [1.5 m] min. (system centerline to door) Mounting Foot Outline 79.5 in. [202 cm] Mounting Foot 5 ft. [1.5 m] min. (system centerline to door) Mounting Foot Outline Electrical Supply Box Hardwired to power cord. 2.5 inch (min) clearance from center of mounting foot. 41 in. [1.04 m] (Typical) min. 8800_CP_ _B

22 Warranty One Year Library Systems Product Performance Guarantee: Subject to the Limitation of Liability below, 3M guarantees your satisfaction with the performance of any 3M Library System Product for 12 months from the date of installation provided that a) you are the original purchaser: b) you have executed a one (1) year 3M Service greement for maintenance of the Library System product; and c) the product has not been subjected to abuse, misuse, accident or neglect. Performance means the product meets 3M published product specifications. If you are not completely satisfied with the performance of your Library System Product, you may return the Library System product for a prompt refund. 3M will pay all reasonable deinstallation and shipping charges to return the product to 3M. Note that all claims under this guarantee must be submitted to 3M within 12 months from the date of installation of the 3M Library Systems Product. Failure to submit a claim within this time frame will invalidate this guarantee. IMPORTNT: Consumables and non-3m branded products are excluded from this Guarantee. Warranty and Limited Remedy for Non-Software Library Systems Products Not Covered by Performance Guarantee: Unless stated otherwise in 3M product literature or packaging, 3M warrants that each 3M Library Systems Product meets the applicable specifications for a period of ninety (90) days from the date of shipment (or, in the case of hardware installed by 3M, from the date of installation). ny warranties related to 3M software are contained in separate 3M software licenses. Consumables and non-3m branded products are excluded from this Warranty and Limited Remedy. 3M MKES NO OTHER GURNTEES, WRRNTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, NY IMPLIED WRRNTY OR CONDITION OF MERCHNTBILITY OR FITNESS FOR PRTICULR PURPOSE OR NY IMPLIED WRRNTY OR CONDITION RISING OUT OF COURSE OF DELING, CUSTOM OR USGE OF TRDE. You are responsible for determining whether the 3M product is fit for a particular purpose and suitable for your application. If the 3M product is defective within the warranty period and provided that a) the product has not been subjected to abuse, misuse, accident or neglect and b) you have notified 3M within thirty (30) days after the defect was discovered, your exclusive remedy and 3M s and seller s sole obligation will be, at 3M s option, to replace or repair the defective 3M product. Limitation of Liability: EXCEPT WHERE PROHIBITED BY LW, 3M ND SELLER WILL NOT BE LIBLE FOR NY LOSS OR DMGE RISING FROM 3M LIBRRY SYSTEMs, WHETHER DIRECT, INDIRECT, SPECIL, INCIDENTL OR CONSEQUENTIL, REGRDLESS OF THE LEGL THEORY SSERTED, INCLUDING WRRNTY, CONTRCT, NEGLIGENCE OR STRICT LIBILITY. Guarantee and Warranty Claims: For guarantee and warranty claims, and for service, call one of the following numbers: In the US: In Canada: English Francais: