Removing and installing light switch unit

Size: px

Start display at page:

Download "Removing and installing light switch unit"

Roberta Pitts
5 years ago
Views:

AIR - Repair instruction https://myair-bdr.bmwgroup.com/air/faces/xhtml/tdoc/tdocsingleview.xhtml?st=repa.

1 AIR - Repair instruction Page 1 of 2 BMW Group - AIR: / 07:59 Dealer: 32711/06 Model: 325XI A Development code: E46 Model code: EU43 Lead type: EU43 Order number: - Repair instruction Removing and installing light switch unit Removing and installing light switch unit Unclip left wooden finisher, refer to Remove left glovebox, refer to Release screws (1). Press switch unit up a little through glovebox aperture and then slide back.

2 AIR - Repair instruction Page 2 of 2 Unlock plug and remove.

3 Page 1 of 7 BMW Group - AIR: / 07:59 Dealer: 32711/06 Model: 325XI A Development code: E46 Model code: EU43 Lead type: EU43 Order number: - Removing and installing light switch unit» Replacing a clipped-in trim (decorative strip on panel for instrument panel, front or rear door) REP-REP-RAE Replacing a clipped-in trim (decorative strip on panel for instrument panel, front or rear door) Special tools required: Replacement of: Decorative strip on front or rear door or side trim Warning! Version with side and passenger airbags: Follow safety instructions for working on cars with airbag systems, refer to Warning! Incorrect combination of pin and clip (Hutfix): the decorative strip may come loose when the passenger airbag is triggered (risk of injury). The pins must therefore always be measured.

7 mm (always measure) - The decorative strips for replacement are always supplied with a pin diameter of 6.0 mm, these pins

4 Page 2 of 7 Caution! Decorative strips above glovebox, on light switch and above radio are secured with different pins and clip (Hutfix). On all cars without screw (1): - the clips (2) of instrument panel are "white" - the pins of decorative strip are "yellow" - the pins must have a diameter of 5.7 mm (always measure) - The decorative strips for replacement are always supplied with a pin diameter of 6.0 mm, these pins must be replaced by 5.7 mm dia. pins. On all cars with screw (1): - the clips (2) of instrument panel are "red" - the pins of decorative strip are "red" or "plain" - the pins must have a diameter of 6.0 mm (always measure) Replacing clips (Hutfix) on instrument panel: A Use screwdriver to turn clip (1) through approx. 30 to left B Lever out clip (1) from below Retainers (1) on clip (2) must not be

Page 3 of 7 damaged. Do not damage support (3) in instrument panel (4).

through approx. 30 to right B Clip (1) in end position Decorative strip on light switch: Caution!

Insert special tool 00 9 321 (fishbone) at side and with second special tool 00 9 321 next to

5 Page 3 of 7 damaged. Do not damage support (3) in instrument panel (4). A Insert clip (1) from above and snap into place at bottom Use screwdriver to turn clip (1) through approx. 30 to right B Clip (1) in end position Decorative strip on light switch: Caution! Carefully unclip decorative strip with two special tools (fishbone) (risk of damage). Insert special tool (fishbone) at side and with second special tool next to retaining pin, refer to next work step, unclip decorative strip (1). If necessary, replace faulty pins (1) of decorative strip (2).

Page 4 of 7 Model with real wood: If necessary,

strip (2). Tightening torque, 51 16 8AZ.

Decorative strip above glovebox: Caution!

6 Page 4 of 7 Model with real wood: If necessary, replace faulty screw-in pins (1) on decorative strip (2). Tightening torque, AZ. Push guides (1) onto locators (2). Decorative strip above glovebox: Caution! Carefully unclip decorative strip with two special tools (fishbone) (risk of damage).

Page 5 of 7 Insert special tool 00 9 321 at side and with second special tool 00 9

If necessary, replace faulty pins (1) of decorative strip (2).

7 Page 5 of 7 Insert special tool at side and with second special tool next to retaining pin, refer to next work step, unclip decorative strip (1). If necessary, replace faulty pins (1) of decorative strip (2). Model with real wood: If necessary, replace faulty screw-in pins (1) on decorative strip (2). Tightening torque, AZ. Decorative strip above radio: Remove decorative strip above glovebox. Unclip decorative strip (1) with special tool (fishbone) (risk of damage).

Page 6 of 7 If necessary, replace faulty pin (1) on

Check that screws (3) on bracket (4) are properly

8 Page 6 of 7 If necessary, replace faulty pin (1) on decorative strip (2). Model with real wood: If necessary, replace faulty screw-in pins (1) on decorative strip (2). Tightening torque, AZ. Check that screws (3) on bracket (4) are properly seated. Push guides (1) into locators (2). Clip in decorative strip completely.

9 Page 7 of 7

Page 1 of 1 BMW Group - AIR: 2017-11-22 / 07:59 Dealer: 32711/06 Model: 325XI A Development code: E46 Model code: EU43 Lead type: EU43 Order number: - Removing and installing light

10 Page 1 of 1 BMW Group - AIR: / 07:59 Dealer: 32711/06 Model: 325XI A Development code: E46 Model code: EU43 Lead type: EU43 Order number: - Removing and installing light switch unit» Removing and installing left glove box REP-REP-RAE Removing and installing left glove box Open glovebox. Release screws (1) and remove glove box (2).

Removing and installing the dash panel

Стр. 1 из 6 Removing and installing the dash panel Removing: WARNING Disconnect battery earth strap Electrical System Rep. Gr.27. Removing the centre console Chapter. Remove the steering wheel Chapter.