MODEL 4356A MIXER-GRINDER

Transcription

1 INSTRUCTION MANUAL with Replacement Parts MODEL 4356A MIXER-GRINDER (INCLUDES MOTOR PARTS) ML 3679 ML-3680 A product of HOBART CORPORATION TROY, OHIO FORM 545 (7-84)

2

3 INSTRUCTIONS 4356A Instructions for Operation and Care of MODEL 4356A MIXER-GRINDER GENERAL The model 4356A Mixer-Grinder is designed to process fresh boneless, pre-ground, tempered flaked frozen or a combination of these meats. The hopper volume is 4 cubic feet which provides a weight capacity up to 500 pounds, depending on type of product. Two motors are used in this machine a 5 horsepower motor for grinding and a 5 horsepower motor for mixing. This allows the operator to feed and grind, mix onty, or grind only Using the feed screw and overlapping mixing arms, blending meats, moisture, seasoning, and extenders is quick and efficient. After MIXING, switching to FEED AND GRIND provides steady output of ground meat without bridging. A MOMENTARY GRIND ONLY operation is also Fig. available. Should the grinder cylinder become jammed with meat or clearing of grinder cylinder If machine was shipped with mixing arms installed, desired, selection of GRIND ONLY empty it. they should be removed at this time. Rotate the In this mode of operation, just the grinder motor mixing arm (3, Fig. ) by hand until the L.H. runs. The feed screw does not feed additional drive shaft notch (A, Fig. ) is at the vertical top. product to the grinder cylinder. Options High speed grinder gears are available which will increase the grinder worm speed from a standard 5 R.P.M. to 88 R.P.M. High speed gears are never to be used for first grind beef. Optional sprockets (along with the proper drive chains) may also be ordered to increase the feed (conveyor) screw speed from 5 to 0 R.P.M. and the arms from 4 to 45 R.P.M. INSTALLATION NOTCH VIEW TOWARD SPROCKET END FROM INSIDE OF HOPPER. l.h. DRIVE SHAFT Unpack the mixer-grjnder, install the floor leveling feet and place it in operating position. Adjust the leveling screws so the cylinder end is approximately /" to " lower than opposite end, thus PL-766i allowing water to drain out of the hopper and grinder cylinder when cleaning. Fig. R.H. DRIVE SHAFT B HOBART CORPORATION, 980-3

4 4356A INSTRUCTIONS o o 7 PL-943l-l( Fig. 3 Loosen the two thumb screws (, Fig. 3) that retain the mixing arm stub shaft (, Fig. 3). Rotate and remove the L.H. stub shaft while supporting the front end of the mixing arm inside the hopper. Remove the mix;ng arm" The other mixing arm is removed in the same manner. Electrical WARNJNG: ELECTRICAL AND GROUNDING CONNECTIONS IVUST Y WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AT FUSED DiSCONNECT SWITCH AND PLACE A TAG INDICATING CIRCUIT IS BEING WORKED ON. All internal of the machine is compjeted before shipping. Before making electrical supply connection, check the specifications on the data plate (8, Fig. 3) to assure they agree with those of your electrical service. See wiring diagram inside sprocket drive case (9, Fig. 3). Make erectrical connections per the wiring diagram. BRANCH CIRCUIT SIZE AND PROTECTION DUAL ELEMENT TIME-DELAY FUSE Maximum 75 C Circuit Fuse Copper Volts Phase Ampacjty Size Wire Size

5 INSTRUCTIONS 4356A INVERSE TIME BREAKER Minimum Maximum 75 C Circuit Circuit Copper Volts Phase Ampacity Breaker Size Wire Size Motor Rotation A fter the electrjcal connection is made, the machine must be checked for correct motor rotation. Install the feed chamber (3, Fig. 3) and tighten the cylinder nuts. Apply electrical power to machine and place the selector switch (4, Fig. 4) in GRIND ONLY. Push the START FEED AND GRIND/ GRIND switch (, Fig. 4) momentarily and release. 4 mineral oil after installation and before being for service. ASSEMBLY DISCONNECT ELECTRICAL POWER SUPPLY and slide the conveyor screw (, Fig. ) the length of hopper and into square drive shaft. Install grinder cylinder (4, Fig. 3) on the three studs at the hopper end. Secure with cylinder nuts. Install the feed chamber (3, Fig. 3) and tighten the four nuts. power to the machine, place the selector switch (4, Fig. 4) in FEED AND and operate to position drive shaft notches A & B as shown in Fjg.. DISCONNECT ELECTRICAL POWER SUPPLY and install a mixing arm (3, ) into the L.H. drive shaft (, Fig. ). While holding the opposite end of the arm install the stubshaft (, Fig. 3) and tighten the two thumb screws (, Fig. 3). Rotate the mixing arm by hand until notch (F ig. ) of the R. H. drive shaft is up. Insta II the second mixing arm into the R.H. drive shaft. While the opposite end of the arm, install the stubshaft and tighten the two thumb screws. Check mixing arm clearance by manually rotating assembled arms one compjete turn before applying power. the worm into the cylinder and rotate until the square shank of the worm locks into the attachment hub drive. Install the grinder knife with cutting edges out. Fig. 4 If the machine rotation is correct, the square drive shaft will turn counterclockwise while facing the feed chamber. the machine rotation is incorrect, oil wijl be pumped out of the transmission. DISCONNECT ELECTRICAL POWER SUPPLY and interchange any two power supply reads at the terminar Start the machine momentarily to verify counterclockwise (see arrow) rotation while facing the attachment hub. Sanitizing NOTE: The 4356A Mixer-Grinder must be thoroughly cleaned, sanitized and lightly coated with Install the grinder plate on the worm using caution to align the plate with the alignment pin. Thread the adjusting ring (6, Fig. 3) loosely on the cylinder. the meat deflector (5, Fig. 3). OPERATION NEVER PUT HAND OR ARMS INSIDE HOPPER unless mixer-grinder is disconnected from electrical power supply. Spring-loaded safety rails (0, Fig. 3) are hinged at the hopper ends. If either rail is bumped, it pivot, open the interlock, and stop the machine. The spring wilt return the safety rail to its operating position crosing the interlock. The machine wi resume the selected function when restarted by operator. -5

6 4356A INSTRUCTIONS The feed chamber, secured to the machine hopper by four nuts, must be in position for machine operation. If the feed charrlber is moved from its operating position during operation, an interlock switch will open and stop the machine. The feed chamber must be correctjy instaued and the machine restarted. Controls The box (7, Fig. 3), with switches for selecting modes of operation, is located on the hopper. The STOP switch (, Fig. 4) is used to stop all modes of operation. When changing from one operation to another, the STOP switch rrlust first be pushed. The START M IX switch (3, Fig. 4) is pushed when it is desired to mix the product that is in the hopper. During the MIXING ON LY cycle, the hopper conveyor screw and mixing arms operate in a reverse direction assuring a complete of all ingredients in the hopper and preventing meat from entering the feed chamber. Extended mixing may damage meat. The selector switch (4, Fig. 4) is used to select either the FEED AND GRIND or the GRIND ONLY operation. When the START FEED and GRIND/GRIND switch (, Fig. 4) is pushed, the machine will operate in the mode selected by the Selector switch (4, Fig. 4). Running The knife and plate depend on the meat for lubrication. When starting a cleaned machine the adjusting ring should be Jeft loose until meat begins to come through knife and Once ground meat is visible, the adjusting ring shou Id be tightened hand tight. The two motors on the mixer-grinder are protected by thermal overloads which sense motor temperature. If either motor overheats, the machine will stop. When motor(s) has cooled, the mixer-grinder can be started. MAl NTENANCE WARNJNG: DISCONNECT ELECTRICAL POWER SUPPLY AT FUSED DISCONNECT SWITCH AND PLACE A TAG INDICATING CIRCUIT IS BEING WORKED ON BEFORE BEGINNING AND MAINTENANCE PROCE DURE. Cleaning NOTE: The control box is provided with heaters to minimize condensation. After cleaning, connect power supply so the heater be on. Regular cleaning is required at the end of each working shjft or whenever the machine is to be out of service for an extended period of time (overnight). The machine is designed for easy cleaning by removing the following components: meat deflector (5/ Fig. 3); adjustjng ring (6, Fig. 3); plate and knife; worm; feed chamber (3, Fig. 3); cylinder (4, Fig. 3); mixing arms (3 & 4, Fig. ) and conveyor screw (, Fig. ). A rubber seal at each of the three driving shafts (inside the hopper) may be removed for cleaning by grasping the outer or using a dull screwdriver tip and pulling seal out. The grinder can be washed down with high pressure hot water or steam as is customary in meat processing operations. CAUTION: Use care to avoid direct high pressure flushing of the control box, electrical connections, etc. DO NOT assemble the feed chamber to the machine untij the grinder is to be used for processing a product. The feed chamber js interlocked to prevent accidental starting. Sanitizing The 4356A Mixer-Grinder must be thoroughly sanitized and Jightly coated with mineral oil before being reassembred for service. Lu brication Motor transmissions are lubricated at the factory. A dip stick (, Fig. 5) at each transmission is provided for regular checking of the oil level. Drain and the transmission annually with Mobil Lube H.D. - BOW The idler spocket should be lubricated at both fittings ( &, Fig. 6) with Alvania lube after each 0 hours of operation. The roller chains (3, Fig. 6) should be lubricated with LPS after each 0 hours of operation. Air Intake Under normal operating conditions, the motor air intake screens (rocated under each gear case) may -6

7 INSTRUCTIONS 4356A Fig. 5 require occasional cleaning. In installations where flour, seasonings or other foreign materials are present in the air, the screens may become par tjally or completely covered, restricting coohng air to the motors. With a clean cloth or soft bristle brush, clean as required. TROUBLESHOOTING Symptom - No rvlachine Operation Possible Cause: Symptom - Noise In Gear Cases Or Sprocket Drive Case. Possible Cause:. May be due to inadequate lubrication. See Main tenance for recommended lubrication procedures. If any symptom persists, contact your local Hobart Service Office.. One or more of interlocked components not in operating position.. Electrical power supply fused disconnect switch in open position. 3. Blown fuse or tripped c;rcu it breaker at electrical power supply. Synptom - Adjusting Ring Won't Thread Completely On Cylinder. Possible Cause:. Threads on cylinder and/or in adjusting ring are clogged with dried meat particles. Thoroughly clean and oil with tasteless mineral Fig. 6-7

8 4356A REPLACEMENT PARTS I PL-943I FRAME AND HOPPER UNIT - 8

9 m m m m -». o m_ [ PL-5575!

10 .. REPLACEMENT PARTS 4356A FRAME AND HOPPER UNIT ILLUS. PL PART NO. C 4790 E-I0765 A-I0537 E-945- E-945- E E B-0874 WS-9- WL-6-8 NS-5-3 5D B-3705 S D-0389 B-793 P C D M-6986 B-96 D-9456 M D M-8380 WL-4-6 NS-3 5 B-0874 WL-6-8 N M-I0557 NAME OF PART 0 D.. st Cut Mixing Arm (Incls. item #3).. nd Cut Mixing Arm (Incls. item # 3) Mixing Arm Bushing & Loctite Assy.. Frame & Hopper Assy. (R.H.) (33-/" Floor to Center Line Cylinder).. Frame & Hopper Assy. (R.H.) Floor to Center Line Cylinder).. Frame & Hopper Assy (L.H.) (33-/" Floor to Center Line Cylinder).. Frame & Hopper Assy. (L.H.) Floor to Center Line Cylinder).. Pivot Bolt - Safety Rail.. Washer. Lock Washer - Full Nut - Medium Hex Fin " " "... Self-Tapping Screw #0-4 x " Pan Hd., Type F.".. Motor Shield ". Wrench - Spanner (#56). Wrench - Spanner (#66) ".. Foot - Adjustable Shaft - Mixer Arm Stub. D D.. Safety Rail Assy.. Shield - Motor " D D.. Nut -Cylinder ". Feed Screw Bushing Assy ". Cylinder Feed Chamber Assy. (ncls. item #) Wrench - Cylinder Nut D. "Ot'Ring.. Screw - Spanner Wrench Support Lock Washer 3/8 Medium ". Full Nut.. 3/8"-6 Hex Fin. Pivot Bolt - Safety Rail.. Lock Washer - 3/8" Medium. Full Nut - 3/8"-6 Hex Fin. Conveyor Screw Assy ".. Thumb Nut Assy D AMT. 6 4 I 4-9

11 REPLACEMENT PARTS 4356A GEAR CASE UNIT (5 H.P.) (GRINDER) ILLUS. PART PL-5575 NO. NAME OF PART AMT. NS-3-43 Full Nut - 5/8"- Hex Fin. 3 M-798- Stud - Cylinder (4" Lg.) SC-8-3 Carriage Bolt - /4"-0 x I" Hub.. Attachment (Grinder End). 5 WL-8-7 Lock Washer - /4 Int. Shakeproof NS-3- Full Nut - /4"-0 Hex Fin. 4 7 NS-3-43 Full Nut - 5/8"- Hex Fin. 3 8 SC-6-4 Cap Screw - 5/6"-8 x -/" Hex Hd. It 9 WL-3-45 Lock Washer - 5/6" Extra Heavy 0 B-l6775 Conveyor - Oil "... BR--9 Roller Bearing - Cup & Cone Assy. I SC-69- Mach. Screw - #0-3 x 5/8" Phil. Pan Hd.,. I 3 C-I Key.. 4 D Gear - Chopper Drive (56T) 5 B-343 Washer - Tongue It.. 6 WL-7-9 Lock Washer - Timken #TWI07. 7 Lock Nut - N.D. # N V-6566 Lock Nut. 9 WS-ll-4 Washer. 0 C-I0907o-7 Key C-858- Gear - Motor Pinion (4T) C-858- Gear - Motor Pinion (9T) (High Speed). 3 M-7536 Flinger - Oil ".. " M-7S37 Spacer - Oil Flinger " " AR Dowel.. 6 M Bushing - Air Vent It M Vent - Air " 8 T Case - Gear. 9 B Motor (00/400 V., 60 Hz., 3 Ph.) Motor (30/460 V., 60 Hz., 3 Ph.).. 3 B Motor (30/400 V., 50 Hz., 3 Ph.). 3 B-374- Spacer - Motor Mounting. 33 WL-4-6 Lock Washer 3/8" Medium. 34 SC-4-36 Cap Screw - 3/8 ' -6 x -/" Hex Hd. 35 COOl 047 Screen - Air Inlet. 36 NS-5-3 Full Nut - 3/8"-6 Hex Fin.. 37 SC-4-3 Cap Screw - 3/8"-6 x -/4" Hex Hd. 38 SC-60- Mach. Screw - #0-4 x /4" Rd. Hd.. 39 WL 3-0 Lock Washer - #0 Light. 40 BB-8-33 Ball Bearing - Fafnir #05K. 4 RR-6-4 Retaining Ring. 4 C-l Key 43 C Ool Gear Main Drive (6ST) ". 44 C Gear - Main Drive (60T) (High Speed) " Pinion - Countershaft (9T) BB-7- Ball Bearing - Fafnir #07K.. 47 B-806 Dip Stick & Cap Assy. 48 FP Nipple - 3/8" x 5" Lg. (T.B.E.). r 49 FP-4- Elbow -, x " P-S697 Bracket - Oil Pipe Support.. 5 FP Nipple - 3/8" x s't Lg. (T.B.E.). 5 M Tee - 3/8" x 3/8 x /4" Reducing " ".. 53 FP-8-9 Plug - 3/8" Sq. Hd. Pipe " 54 FP Nipple - /4 xlii Lg. (T.B.E.).. 55 M-798- Stud - Cylinder (4-/ Lg.). 56 R Shaft - Square Drive.. 57 M-7535 Seal.. 58 BR--8 Roller Bearing - Cup & Cone Assy. 59 Washer. AR 60 B-533 Spacer. -

12 4356A REPLACEMENT PARTS (PL-J MOTOR UNIT (5 H.P -

13 REPLACEMENT PARTS 4356A MOTOR UNIT (5 H.P.) ILlUS. PART PL 5530 NO. NAME OF PART AMT. D-784 Fan. BB-6-37 Ball Bearing - NTN #6304LLU..... I.. I 3 RR-4-6 Retaining Ring. I.. 4 C-I Key. I I I. 5 Set Screw - /4"-0 x 3/8" Soc. Hdls., Kn. Cup Pt. 4 6 SC-9-79 Mach. Screw - #6-3 x 5/6" Rd. Hd. 4 7 C-7557 Cover - Terminal Box I I 8 B-759 Terminal Block I I I I. 9 5C--36 Mach. Screw - # 0-4 X FiL Hd. 0 5C--98 Mach. Screw - 5/6"-8 x -/4" FiL Hd I Bracket - Bearing... I.. I I SC I Mach. Screw - # 0-3 x 7-/8" Rd. Hd WL-3-0 Lock Washer - # 0 Light I.. I D Stator Assy. (00/400 V., 60 Hz.) I e D. 5 D Stator Assy. (30/460 V., 60 Hz.). I I Stator Assy. (575 V. t 60 Hz.) I e I I Stator Assy. (50Hz.) I e. 8 \VL-3-43 Washer - 5/6" Light. I D 3 9 5C Cap Screw - 5/6"-8 x " Soc. Fit Hd 3 0 C Rotor Assy. BB-0-5 Ball Bearing - Fafnir 07KD I. M Spacer - Bearing M-8375 Detlector - (,rease I 4 WL-3-43 Lock \Vasher - 5/6" Light.. I e.. 5 5C--98 Screw - 5/6"-8 x -/4" Fil. Hd Field Ring. I 7 RP-6-3 I Roll Pin -.9" Dia, x 5/8" Lg. I 4-3

14 m m m 53 o 6 z 0» \\ \ \ zz 0 -:c z

15 REPLACEMENT PARTS 4356A GEAR CASE UNIT (5 H.P.) (CONVEYOR SCREW AND MIXING ARMS) ILLUS. PART PL-5576 NO. NAME OF PART AMT. B Motor (00/400 V., 60 Hz., 3 Ph.). B Motor (30/460 V., 60 Hz., 3 Ph.) B Motor (30/400 V., 50 Hz., 3 Ph.) 4 M Yent - Air a Dowel. 6 M-7537 Spacer - Oil Flinger AR 7 M-7536 Flinger - Oil C-858- Gear - Motor Pinion (4T). 9 C-I Key ". 0 WS--4 Washer V-6566 Lock Nut ".. WL-7-9 Lock Washer - Timken #TW07. 3 B-343 Washer - Tongue. 4 C Key. 5 D Gear - Chopper Drive (56T) BR--0 Roller Bearing - eup & Cone Assy " " B-6775 Conve yor - Oil " ".. 8 SC-69- Mach. Screw #0-3 x 5/8" Phil. Pan Rd. a 9 WL-345 Lock Washer - 5/6" Extra Heavy 0 SC-6-4 Cap Screw - 5/6"-8 x -/" Hex Hd. E-868 Hub - Attachment (Sprocket End) P Gasket - Attachment Hub.. a D D BR-- Roller Bearing - Cup & Cone Assy. 4 B-0058 Seal - Bearing Oil Shaft - Chain Drive. 6 SC-6-3 Cap Screw - 5/8"- x " Hex Hd.. 7 WL-4-7 Lock Washer - 5/8" Light co.. 8 B-806 Dip Stick & Cap Assy. 9 FP Nipple - 3/8" x 5" Lg. (T.B.E.) ". 30 FP-4- Elbow.. 3/8" x FP Nipple 3/S n x 5 Lg. (T.B.E.) ". D 3 M Tee - 3/8" x 3/8" x /4" Reducing. 33 FP-8 9 Plug - 3/8" Sq. Hd. Pipe. 34 FP-37-5 Nipple - /4" x I" Lg. (T.B.E.).. 35 P-8697 Bracket - Oil Pipe Support.. 36 BB-7- Ball Bearing.. Fafnir #07K " Pinion - Countershaft (9T) ".. 38 NS-34-8 Lock Nut - N.D. #N C-I Key.. 40 C Gear - Main Drive (65T). 4 RR-6-4 Retaining Ring BB-8-33 Ball Bearing - Fafnir #0SK. 43 NS-5-3 Cap Screw - 3/8 ' -6 Hex Fin " " ". 44 SC-4-3 Cap Screw - 3/8"-6 x -/4" Hex Hd. 45 C-047 Screen - Air Inlet " " SC-60- Mach. Screw - #0-4 x /4 n Rd. Hd ". 47 WL-3-0 Lock Washer - #0 Light ".. " " ".. 48 SC-4-36 Cap Screw - 3/8"-6 x -/" Hex Hd " " ".. ". 49 WL-4-6 Lock Washer - 3/8" Medium. 50 B-374- Spacer - Motor Mounting " " ".. 5 B-533 Spacer" " ". 5 WS-8-4 Washer ".. " " " " " " AR 53 T Case - Gear " ".. 54 M Bushing - Air Vent " " " - 5

16 4356A REPLACEMENT PARTS I I PL-559 MOTOR UNIT {5 H.PJ

17 REPLACEMENT PARTS 4356A MOTOR UNIT (5 H.P.) JlLUS. PART Pl-559 NO. NAME OF PART AMT. D I BB-6-37 Ball Bearing - NTN. I 3 RR-4-6 Retaining Ring _ I 4 C-I Key SC-47- Set Screw - /4"-0 x 3/8(# Soc. Hdls.. Kn. Cup Pt. 6 5C-9-79 Mach. Screw - #6-3 x 5/6(# Rd. Hd. 4 7 C-7557 Cover Terminal Box. I 8 B-759 Terminal Block. 9 5C--36 Mach. Screw - # 0-4 3/4" Fil. Hd. 0 5C--98 Mach. Screw - 5/6"-8 x -/4" Fil. Hd. 3 E-755 Bracket - Bearing _.... _... SC--6 Mach. Screw - #0-3 Fit Hd \VL-3-0 Lock Washer - # 0 Light D Stator Assy. (00/400 V., 60 Hz.). IS D Stator Assy. (30/460 V., 60 Hz.). 6 D Stator Assy. (575 V., 60 Hz.) D Stator Assy. (50 Hz.). 8 \VL-3-43 Lock Washer -5/6" Light SC Cap Screw - 5/6"-8 x " Soc. Fit Hd C Rotor Assy. BB-0-5 Ball Bearing - Fafnir #07KD M Spacer Bearing M-8375 Deflector - Grease WL-3-43 Lock Washer - 5J6" Light C--98 Mach. Screw - S/6 f -8 -/4 Fit Hd E Field Ring RP-6-3 Roll Pin -.9" Dia. x Lg

18 4356A REPlACEMENT PARTS _ ~ ---3 \ \ IPL-t5577 SPROCKET DRIVE CASE UNIT

19 REPLACEMENT PARTS 4356A SPROCKET DRIVE CASE UNIT ILLUS. PART PL-557 NO. NAME OF PART AMT. E-0895 Drive Case Assy Cover - Drive Case ".. 3 se-90-l Cap Screw - /"-3 x " Hex Hd.. 4 WL-4- Lock Washer - Medium.. 5 M-8706 Block Rear Adjustable.. 6 NS-3-33 FulINut-l/"-3 Hex Fin. 7 SC 40 8 Cap Screw - u -3 x -/" Soc. Fit Hd.. 8 WS-7-9 Washer SC-4I-3 Cap Screw - /4"-0 x -/8" Hex Hd SC-4-44 Cap Screw -/"-3 x -/4" Hex Hd.. 4 WL-4-I Lock Washer - /" Medium.. 4 N Full Nut -/"-3 Hex Fin. 4 3 WL-4- Lock Washer - /" Medium (With Stud) It M Sleeve - Spacing.. 5 SC ft Cap Screw -I 3 x -3/4" Hex Hd " Ball Bearing (MRC #308SZZ) " " " Carrier - Bearing (Mixing Arm) " " ". 8 WL-4- Lock Washer - /" Medium " " " 6 9 NS-3-33 Full Nut - /"-3 Hex Fin " " SC Cap Screw -/"-3 x -3/4" Hex Hd " " ".. 3 NS-3-33 Full Nut - /"-3 Hex Fin. (With /" Stud) ".. 6 M Sleeve - Spacing " BB-0-3 Ball Bearing (MRC #308SZZ).. 4 NS-3-33 Full Nut - /"-3 Hex Fin. (With /" Stud) " " " WL-4- Lock Washer /" Medium (With Stud) Carrier - Bearing (Conveyor Screw) "." ".. 7 BB-0- Ball Bearing (MRC #09SZZ) ". 8 M-7535 Seal - Outer " " ".. 9 M Seal - Inner " Shaft - Conveyor Square Drive.. 3 D-3456 Shaft - Mixing Arm Drive " ".. 3 NS-3-33 Full Nut - /"-3 Hex Fin WL-4- Lock Washer - /" Medium " M Seal - Inner. " " M-7535 Seal- Outer It.. 36 DB-0-II Ball Bearing (MRC #09SZZ) Bearing Carrier Assy. (Mixing Arm) (Incls. items # 6, 7, 3, 35 & 36) Bearing Carrier Assy. (Conveyor Screw) (lncis. items #3, 6, 7, 8 & 30).. -9

20 4356A REPLACEMENT PARTS 9 0 I SPRoeKET DRIVE UNIT

21 t REPLACEMENT PARTS 4356A SPROCKET DRIVE UNIT ILLUS. PART PL 5578 NO. NAME OF PART AMT. SC-40-8 Cap Screw - /".. 3 x -/" Soc. Fil. Hd. NS-3-33 Full Nut - /"-3 Hex Fin. 3 R Idler Sprocket Support & Needle Bearing Assy. (lncls. items #4 & 8). 4 BN--9 Bearing - Needle (Torrington #B-44-0H).. 5 SC-64-8 Set Screw H -3 x Soc. Hdis., Cup Pt... 6 SC Set Screw - /"-3 x / ' Soc. Hdls., Kn. Cup Pt.. 7 P Sprocket (3T) (Idler) " ". 8 BN- 0 Bearing - Needle (Torrington #M-44) " ". 9 C Sprocket & Bushing Assy. (37T) (Driven, Mixing Arm) (IncIs. item #4) ". 0 B-4545 Link - Connecting (#80 H).. AR D Mixing Arm Drive Chain Assy. (84" Lg.) (Incls. item #0) NS-3-43 Full Nut - Hex Fin ". 6 3 WL-4-7 Lock Washer - 5/8" Light ". 6 4 P-8984 Block - Chain Guide " " WS-I0-4 Washer ".. "..... ".. " " " AR 6 M Spacer " SC Cap Screw - 5/8"- x -3/4" Hex Hd. 6 8 SC-6- Cap Screw - 3/8" 6 x -/4" Hex Hd " B Bushing - Taper Lock (Q) (lncls. item #8). 0 C-I Key " o ".. C Sprocket & Bushing Assy. (37T) (Driven, Mixing Arm) (Incls. item # 9).. OG-3-49 Oiler - /8" Pipe Thd "... " " SC-75-5 Set Screw - 5/6"-8 x 3/8" Soc. Hdis., Cup Pt ".. 4 C-I Key 5 M-894 Washer - Sprocket Spacing. AR 6 E Sprocket (lot) (Driven, Mixing Arm) (Incis. item #3) ".. 7 B Link - Connecting (#80 H) " ".. AR 8 B-49 Link - Offset (#80 H). AR 9 M Conveyor Drive Chain Assy. (45" Lg.) (Incls. items #7 & 8). 30 C Sprocket (9T) (Motor Drive) (Inds. item #34).. 3 C Key. 3 WS-4-43 Washer ". AR 33 RR-6-8 Retaining Ring... " ".. " ft 34 SC-75-5 Set Screw - 5/6"-8 x Soc. Hdls., Cup Pt.. ". 35 C-I Key. 36 P Shaft - Idler Support. 37 B Bushing - Taper Lock (Ql) (Incis. item #38) ". 38 SC-6- Cap Screw - 3/8"-6 x /4" Hex Hd C Sprocket & Bushing Assy. (37T) Conveyor Screw) (Incls. item #37). 40 SC-6- Cap Screw - 3/8"-6 x -/4" Hex Hd. 3 4 B Bushing - Taper Lock (Ql) (lncis. item #40).. 4 OG-349 Oiler - /8" Pipe Thd.. 43 C-I Key ".. ". R Idler Assy. (Inels. items. 6, 7, 36 & 4) " ". D Sprocket & Chain Kit (IncIs. items # & 6 thru 30). -

22 4356A REPLACEMENT PARTS - ~ \ INTERLOCK AND CONTROL BOX UNIT -

23 REPLACEMENT PARTS 4356A INTERLOCK AND CONTROL BOX UNIT ILLUS.. PART PL 88 NO. NAME OF PART AMT Pivot Bolt - Transverse Bar. 096 Spring - Safety Rail " Transverse Bar Assy Limit Switch Assy. (lncls. item #5) " Lever Arm - Limit Switch. 6 SC-98-5 Screw X -/ Rd. Hd WS-9-6 Washer. 8 Mach. Nut #0-4 Hex Selector Switch - NEMA 4-4X Push ButtOD - NEMA Switch Guard Assy ".. SC--8 Mach. Screw - #6-3 x 3/8" Rd. Hd \VS-3-44 Washer D Pilot Light Ass}' Push Button Assy D D Control Box 7 SC-98-5 Screw - #0-4 x -/ Rd.. Hd D Limit Switch Lever Arm.. Limit Switch D. 0 NS-5- FuU Nut - /4"-0 Hex Fin Spacer - Control Box SC-3-3 Mach. Screw - x -3/8" Rd. Rd. Sq. Neck Bracket - Interlock Switch Mounting. 4 \VL-6-8 Lock Washer - 3/8" Medium SC-4-6 Cap Screw - 3/8 '-6 x /" Hex Hd.. 4-3

24 4356A REPLACEMENT PARTS I' II II f, I I' I: II I II II II II II j I II II I' I I 'I 8I I I I 5-6 If I I j I, : I I I I I jl r I I I,,I I I I I I If I I I I I II I L.J I I, I I I I I I I I I I I I l f I I I PL-883- I I I I I CONDUIT (INTERLOCK SWITCHES TO CONTROL BOX) -4

25 If REPLACEMENT PARTS 4356A CONDUIT (INTERLOCK SWITCHES TO CONTROL BOX) ILLUS. PART Pl-883- NO. NAME OF PART AMT. FE-7-4 Connector - Straight "Sealtite" (/'" Male Thd x / N Flex. end.) Conduit - /" x 6 N Flex Hanger - Cable SC--47 Mach. Screw - /4"-0 x Rd. Hd,., \VL-6-7 Lock Washer - /4 't Medium,. 3 6 NS-5- Full Nut - /4"-0 Hex Fin, SC..-37 Mach. Scre\v - 4 ft -0 X Rd. Hd,., WL-6-7 Lock Washer.. /4 t Medium. 3 9 FE-7-4 Connector - Straight "Sealtite" Male Thd. x /" Flex. Cnd.). 0 FE-7-3 Ell x Pulling FE-7-4 Connector - Straight (/" Male Thd. x /" Flex. end.) Conduit - /" x 8-3/4" Flex II 3 FE-7-4 Connector - Straight "Sealtite" (/" Male Thd. x Flex. Cnd.). 4 FE-8-0 /" Gasket Assy. 5 FE-?-? Connector Male Thd. x /" Flex. Cnd.). 6 FE-8-0 / ' Gasket Assy,... 7 FE-7-4 H Connector - Straight "Sealtite (/" Male Thd. x /" Flex. Cnd.) Conduit - /" x " Flex.. - 5

26 4356A REPLACEMENT PARTS 6 /5 4!PL-884- CONDUIT (MOTOR TO CONTROL BOX) - 6

27 H REPLACEMENT PARTS 4356A CONDUIT (MOTOR TO COTROL BOX) ILLUS. PART PL-884-' NO. NAME OF PART AMT. ** FE-8-3 Connector (" Male Thd. xl" Flex. Cnd.). U ** Conduit.. II (Grinder Motor to Control Box). **3 FE-B- I" Gasket Assy **4 FE-B-33 Connector" 90 usealtite" ( Male Thd. xl" Flex. Cnd.) ".. * Conduit - USealtite" (Sprocket Motor to Control Box). *6 FE-B-3 Connector - Straight "Sealtite'" (I" Male Thd. x Flex. Cnd.) _. *7 FE-B- " Gasket Assy *8 FE-8-33 Connector - 90 USealtite" (" Male Thd. xl" Flex. Cnd.) *9 FE-S- I" Gasket Assy * Conduit - II "Sealtite" (Grinder Motor to Control Box).. I * FE-8-3 Connector - 45 (" Male Thd. x Flex. Cnd.). * FE-8-3 Connector.. 45 "Sealtite" (" Male Thd. xl" Flex. Cnd.) **3 FE-8-l III Gasket Assy **4 FE-8-3 Connector - Straight USealtite" (" Male Thd. x II Flex. Cnd.). ** Conduit - " "Sealtite" (Sprocket Motor to Control Box).. ** 6 FE-8-3 Connector 45 0 "Sealtite" (" Male Thd. xl" Flex. end.). *R.H. Mounted Control Box. **L.H. Mounted Control Box. -

28 4356A REPLACEMENT PARTS 0 9 _-, i "' IPL-t CONTROL UNIT - 8

29 REPLACEMENT PARTS 4356A CONTROL UNIT ILLUS. PART PL-88S-' NO. NAME Of PART AMT t SC--3 Mach. Screw - #0-4 x /" Rd. Hd Starter (5 H.P. Motor) 0 AR 3 * Heater Element - Starter " 0 " ". 4 SC-S-8! Mach. Screw - /4 n 0 x /" Rd. Hd WL-8-7 Lock Washer - /4" Int. Shakeproof " " " " " C--3 Mach. Screw - #0-4 x /" Rd. Hd " Control Panel " ".... " Starter (5 Motor) Cl * Heater Element - Starter " 0 " ".. AR Terminal Block Self-Tapping Screw - #6-3 x II Phil. Pan Hd o, Type F... Cl Cl Clamp - Wire " " Self-Tapping Screw - #8-3 x 3/8" Phil. Pan Hd., Type F " 0 " " " Cl Shield - Heater 0. 5 S0-9-4 Self-Tapping Screw - #8-3 x 3/8" Phil. Pan Hd., Type F Clamp... 7 So.9-4 Self-Tapping Screw - #8-3 x 3/8" Phil Pan Hd., Type F Heater & Terminals " 9 WS-9-tO Washer. 4 0 SD-9-5 Self-Tapping Screw - #0-4 x SISN Pan Type F Transformer.. " 5D-9-4 Self-Tapping Screw - #8-3 x Phil. Pan Hd., Type F 0. 3 FE--5 Fuse (.6 Amp.) (460 V.) FE--74 Fuse (.6 Amp.) (500 V.) 5 FE--86 Fuse - Time Delay (.8 Amp.) (SOO V.) Fuse Board WL-IO-l Lock Washer - #8 Ext. Shakeproof. 8 SC-7-9 Mach. Screw - #8-3 x 3/8" Rd. Hd ". 9 WL-6-8 Lock Washer - 3/8" Medium NS-5 3 Full Nut - 3/8"-6 Hex Fin Lug - Solderless.. *Give Elec. Spec., Mach. Model & Motor Type - 9

30 4356A REPLACEMENT PARTS 3 6 IPL GRINDER UNIT ILLUS. PART PL-5704 NO. NAME OF PART AMT. M-6986 Nut - Cylinder. M-8378S Stud - Conveyor Screw Chamber Mtg.. 3 A-I0354- Grinder Cylinder Assy. (Spiral Flute) (lncis. items # & 5). 4 A-I03S4-3 Grinder Cylinder Assy. (Straight Flute) (Not Shown) (incis. items # &. 5). 5 C Dowel. 6 C-480 Worm Assy. (Incls. item #7).. 7 R Stud. 8 Knife * Plate.. Grinder R-8799 Ring - Adjusting R Deflector Assy high quality knives and plates should be purchased or rented for grinder. - 30

31 REPLACEMENT PARTS 4356A 0 \ \ t PL-I GRINDER UNIT ILLUS. PART PL 665 NO. NAME OF PART AMT. M-6986 Nut - Cylinder. M Stud Conveyor Screw Chamber Mtg. 3 A-I0354- Grinder Cylinder Assy. (Incls.o items # & ). 4 C-489 Worm Assy. (lncls. item #5). 5 C I04039 Stud.. 6 Knife - Grinder * 7 Plate - Grinder. 8 D-I034 Ring - Adjusting Deflector Assy. (IncIs. item # 0). 0 C-I0897- Thumb Screw.. D Dowel. *Sharp, high quality knives and plates should be purchased or rented for this grinder. - 3

32 o f. o z c: r o o» DIM E..FLOOR CONTROL SOX POSITIONED AT THIS LOCATION ON THIS SIDE FOR A R.H. MACHINE. ON OPPOSITE SIDE A LH. MACHINE - OIA HOLE FOR I" CONDUIT FITTING OTHER LOCAL COOES. THE ADJUSTING RING DIMENSION $ 6- WITH \HOBART! TROV, OHIO NO c: