General Specifications
|
|
- Elmer Potter
- 5 years ago
- Views:
Transcription
1 General Specifications Model EJB430 Gauge Pressure Transmitter GS 01C23E01-00E [Style: S2] The model EJB430 Gauge Pressure Transmitter can be used to measure liquid, gas, or steam pressure. It outputs a 4 to 20 m DC signal corresponding to the measured gauge pressure. The model EJB430 also features remote setup and monitoring through communications with the model BT200/100 BRIN TERMINL, CENTUM CS/XL system etc. STNDRD SPECIFICTIONS Measurement s: Capsule B Measurement Span 0.06 to 3 MPa {0.6 to 30 kgf/cm 2 } Measurement -0.1 to 3 MPa {-1 to 30 kgf/cm 2 } 0.46 to 14 MPa -0.1 to 14 MPa {4.6 to 140 kgf/cm 2 } {-1 to 140 kgf/cm 2 } Maimum Overpressure 4.5 MPa {45 kgf/cm 2 } 21 MPa {210 kgf/cm 2 } T01E.EPS Output Signal: 4 to 20 m DC, 2-wire system with digital communication Failure larm: Output status at CPU failure and hardware error; Up-scale: 110%, 21.6 m DC or more (standard) Down-scale: -5%, 3.2 m DC Conditions of Communication Line: Power supply voltage; 16.4 to 42 V DC Load resistance; See Figure 1. Communication distance; 2 km, when CEV polyethylene-insulated PVC-sheathed control cables are used. Note: Communication distance varies depends on kind of cable. Load capacitance; 0.22 F or less. Load inductance; 3.3 mh or less. Spacing from power line; 15 cm or more. Input impedance of receiver connected receiving resistance; 10 k or more at 2.4 khz ccuracy: See Table 1 and Figure 3 Stability*: 0.1 % for 6 months (* 2.) * ZERO ERROR at 23 2 C under atmospheric pressure. is the highest value among the absolute values of the lower range value (LRV) and higher range value (HRV), and the span value in a calibration range. mbient Temperature Limits: -40 to 85 C (-40 to 185 F) (general-use type) -30 to 80 C (-22 to 176 F) (with integral indicator) -20 to 60 C (-4 to 140 F) (JIS flameproof type) mbient Temperature Effect: See Table 1. Process Temperature Limits: -40 to 120 C (-40 to 248 F) (general use type) -20 to 120 C (-4 to 248 F) (JIS flameproof type) mbient Humidity Limits: 5 to 100 % R.H.(at 40 C) Working Pressure Limits: 2.7 kpa abs{20 mmhg abs} to maimum working pressure (See Model and Suffi Codes ). For atmospheric pressure or below, see Figure 2. Power Supply Effect: %/V (21.6 to 32 V DC, 350 ) Mounting: 2-inch pipe mounting. Mounting Position Effect: 390 Pa {40 mmh 2 O}/90. No effect for displacement parallel to diaphragm. These errors can be corrected by the zero adjustment. Degrees of Protection: IP67, NEM4, JIS C0920 immersion proof Eplosion-protected Construction: See Optional Specification. Electrical Connection: See Model and Suffi Codes. Process Connections: See Model and Suffi Codes. Wetted Parts Material: Diaphragm, cover flange, process connector, and vent plug; See Model and Suffi Codes. Capsule gaskets; Teflon-coated JIS SUS316L. Process connector gasket; PTFE (Teflon) Flange Bolts and Nuts Material: See Model and Suffi Codes. mplifier Housing: Cast aluminum alloy. Yokogawa Electric Corporation Nakacho, Musashino-shi, Tokyo, Japan Phone: Fa.: GS 01C23E01-00E Copyright ug th Edition pr. 2006
2 Damping Time Constant: (Sum of time constants for amplifier assembly and capsule assembly) mplifier assembly time constant; Can be set in 9 increments from 0.2 to 64 sec. Capsule assembly time constant; Integral Indicator: LCD digital indicator (optional) < Settings When Shipped > Capsule B Time Constant (sec) ppro. 0.2 ppro. 0.2 T02E.EPS Painting: Polyurethane resin baked finish. For case; frosty white (Munsell 2.5Y8.4/1.2) For cover; deep sea moss green (Munsell 0.6GY3.1/2.0) Eternal Zero djustment: Continuously djustable Resolution; 0.01 % of span Zero djustment Limits: Zero can be fully elevated or suppressed as long as low and high range values are within the measurement range limits of the capsule. Tag Plate: JIS SUS304. Weight: 5.1 kg (11.2 lb) without mounting bracket and process connector. 2 Tag Number Output Mode Display Mode Operation Mode Damping Time Constant *2 s specified in order *1 Linear unless otherwise specified in order Linear unless otherwise specified in order Normal unless otherwise specified in order 2 sec. Calibration Lower Value Calibration Higher Value Calibration Units s specified in order s specified in order Selected from mmh 2 O, mmq, mmwg, mmhg, Pa, hpa, kpa, MPa, mbar, bar, gf/cm 2, kgf/cm 2, inh 2 O, inhg, fth 2 O, or psi. (Only one unit can be specified) *1: Up to 16 alphanumeric characters (including - and ) will be entrered in the amplifier memory. T03E.EPS 600 Eternal load resistance 250 R= E Communication applicable range 100{750} Working pressure KPa abs {mmhg abs} 10{75} pplicable range tmospheric pressure R ( ) 2.7{20} Power supply voltage E (V DC) Figure 1. Relationship Between Power Supply Voltage and Eternal Load Resistance F01E.EPS 1{7.5} Process temperature ( C) Figure 2. Working Pressure and Process Temperature F02E.EPS 0.2 ccuracy 0.1 % 0 capsule 0 0.1{1} 0.3{3} Value of '' 3 MPa{30 kgf/cm 2 } B capsule {4.6} 1.4{14} 14 MPa{140 kgf/cm 2 } () Figure 3. ccuracy F03E.EPS ll Rights Reserved. Copyright 1995, Yokogawa Electric Corporation GS 01C23E01-00E Jan. 05,
3 3 Table 1. ccuracy and mbient Temperature Effect (s Percent of '') *1 Capsule ccuracy mbient temperature effect Zero shift Total shift *2 ( , B 0.1 % For ( ) % For < ) % / 50 C 0.6 % / 50 C change For ( ) % / 50 C For < T04E.EPS *1: '' is the highest value among the absolute values of the lower range value (LRV) and higher range value (HRV), and the span value in a calibration range. Percent of span = Percent of span *2: Combined zero and span shift Table 2. Value of '' Capsule B 0.3 MPa {3 kgf/cm 2 } 1.4 MPa {14 kgf/cm 2 } T05E.EPS ll Rights Reserved. Copyright 1995, Yokogawa Electric Corporation GS 01C23E01-00E pr. 01,
4 4 MODEL ND SUFFIX CODES Model Suffi Codes EJB Output Signal -D Measurement span (capsule) B Wetted parts material *6 S Process connection Bolts and nuts material Installation Electrical connection Integral indicator Mounting bracket Optional codes B D N B C D N Description Gauge pressure transmitter 4 to 20 m DC with digital communication (BRIN protocol) 0.06 to 3 MPa{0.6 to 30 kgf/cm 2 } 0.46 to 14 MPa{4.6 to 140 kgf/cm 2 } [Body] [Capsule] [Vent plug] JIS SCS14 *2 JIS SUS316L *1 JIS SUS316 without process connector (Rc1/4 female on the cover flanges) with Rc1/4 female process connector with Rc1/2 female process connector with 1/4 NPT female process connector with 1/2 NPT female process connector without process connector (1/4 NPT female on the cover flanges) [Maimum working pressure] ( capsule) (B capsule) JIS SCM435 3 MPa {30 kgf/cm 2 } 14 MPa {140 kgf/cm 2 } JIS SUS630 3 MPa {30 kgf/cm 2 } 14 MPa {140 kgf/cm 2 } Vertical impulse piping type, left side terminal bo, right side high pressure, process connector upside *3 Vertical impulse piping type, left side terminal bo, right side high pressure, process connector downside *3 Vertical impulse piping type, right side terminal bo, right side high pressure, process connector upside *3 Vertical impulse piping type, right side terminal bo, right side high pressure, process connector downside *3 Horizontal impulse piping type, left side terminal bo, right side high pressure *4 Horizontal impulse piping type, right side terminal bo, right side high pressure *4 G1/2 female G3/4 female 1/2 NPT female G1/2 female, with eternal indicator connection and a blind plug G3/4 female, with eternal indicator connection and a blind plug 1/2 NPT female, with eternal indicator connection and a blind plug Digital indicator *5 (None) JIS SECC 2-inch pipe mounting (flat type) JIS SUS304 2-inch pipe mounting (flat type) JIS SECC 2-inch pipe mounting (L type) JIS SUS304 2-inch pipe mounting (L type) (None) / Optional specification The marks indicate the most typical selection for each specification. Eample: EJB430-DS5-02NC/ T06E.EPS *1: Diaphragm material is Hastelloy C-276 or STM N Indicated is other capsule wetted parts material. *2: Indicates cover flange and process connector material. *3: If necessary, specify Mounting bracket code C or D. *4: If necessary, specify Mounting bracket code or B. *5: Not available for Installation code -4 and -5. *6: Users must consider the characteristics of selected wetted parts material and the influence of process fluids. The use of inappropriate materials can result in the leakage of corrosive process fluids and cause injury to personnel and/or damage to plant facilities. It is also possible that the diaphragm itself can be damaged and that material from the broken diaphragm and the fill fluid can contaminate the user's process fluids. Be very careful with highly corrosive process fluids such as hydrochloric acid, sulfuric acid, hydrogen sulfide, sodium hypochlorite, and high-temperature steam (150 ºC [302 ºF] or above). Contact Yokogawa for detailed information of the wetted parts material. ll Rights Reserved. Copyright 1995, Yokogawa Electric Corporation GS 01C23E01-00E pr. 01,
5 5 OPTIONL SPECIFICTIONS Item Description Code TIIS Flameproof pproval, E do IIC T4X *10 *12 Eplosionproof type Certificate: TC13814 (Without integral indicator) JF3 TC13815 (With integral indicator) Electrical connection : G1/2 female 1 pc. G11 ttached flameproof packing pplicable cable O. D. : 8 to 12 mm 2 pcs. G12 adapter *1 Electrical connection : G3/4 female 1 pc. G21 pplicable cable O. D. : 10 to 16 mm 2 pcs. G22 Painting Color change Coating change mplifier cover only Epoy resin-baked coating *13 P X1 Lightning protector Transmitter power supply voltage : 10.8 to 32 V DC llowable current : Ma (1 40 s), Repeating 1000 (1 40 s) 100 times Degrease cleansing treatment K1 Oil-prohibited use Degrease cleansing treatment and with fluorinated oilfilled capsule. Operating temperature -20 to 80 C K2 Oil-prohibited use Degrease cleansing treatment and dehydrating treatment K5 with dehydrating treatment Degrease cleansing treatment and dehydrating treatment with fluorinated oilfilled capsule. Operating temperature -20 to 80 C K6 P calibration (psi unit) D1 Calibration units *2 bar calibration (bar unit) ( See Table 3. ) D3 M calibration (kgf/cm 2 unit) D4 Sealing treatment to JIS Sealant(liquid silicone rubber) is coated on JIS SUS630 cover flange mounting nuts against SUS630 nuts stress corrosion cracking. Y Long vent *3 Left side high pressure Total length: 119 mm (standard: 34 mm); Total length when combining with Optional code K1, K2, K5, and K6: 130 mm. Material: SUS316. Process connection : Left side high pressure (standard, right side high pressure) U L Failure alarm down-scale *4 Output status at CPU failure and hardware error. C1 Cover flange *5 M01 Mill Certificate Cover flange, Process connector *6 M11 Pressure test / Test Pressure : 3 MPa{30 kgf/cm 2 } *7 Nitrogen(N 2 ) Gas *9 T03 Leak test Certificate *11 Test Pressure : 14 MPa{140 kgf/cm 2 } *8 Retention time: 10 minutes T02 *1: If cable wiring is to be used to a TIIS flameproof type transmitter, do not fail to add the YOKOGW-assured flameproof packing adapter. *2: The unit of MWP (Ma. working pressure) on the name plate of a housing is the same unit as specified by Optional code D1, D3, and D4. *3 pplicable for vertical impulse piping type (Installation code 0, 1, 2, or 3). *4: The hardware error indicates faulty amplifier or capsule. *5: pplicable for Process connections code 0 and 5. *6: pplicable for Process connections code 1, 2, 3, and 4. *7: pplicable for Capsule code. *8: pplicable for Capsule code B. *9: Pure nitrogen gas is used for oil-prohibited use (Optional code K1, K2, K5, and K6). *10: In case the ambient temperature eceeds 50 C, use heat-resistant cables with maimum allowable temperature of 75 C or above. *11: The unit on the certificate is always MPa regardless of selection of option code D1, D3, or D4. *12: TIIS (The Technology Institution of Industrial Safety) Certification is a new notation for the eplosionproof approval in Japan instead of JIS. *13: Not applicable for color change option. Table 3. Calibration Units Measurement Optional Code Span and D1 ( psi Unit ) D3 ( bar Unit ) D4 ( kgf/cm 2 Unit ) B Span Span 8 to 430 psi 66 to 2000 psi 0.6 to 30 bar 4.6 to 140 bar 0.6 to 30 kgf/cm to 140 kgf/cm 2-15 to 430 psi -15 to 2000 psi -1 to 30 bar -1 to 140 bar -1 to 30 kgf/cm 2-1 to 140 kgf/cm 2 T08E.EPS T07E.EPS ll Rights Reserved. Copyright 1995, Yokogawa Electric Corporation GS 01C23E01-00E pr. 01,
6 6 DIMENSIONS Vertical Impulse Piping Type (Left side Terminal Bo) Unit : mm (appro.inch) Shrouding bolts (Only for TIIS Flameproof type) 193 (7.60) 70 (2.76) 125 (4.92) 27 (1.06) 161 (6.34) 97 (3.82) 104 (4.09) 161 (6.34) 97(3.82) 104 (4.09) 79 (3.11) 68 (2.68) 111 (4.37) 102 (4.02) 53 (2.09) 62 (2.44) 46 (1.81) Open to atmosphere (Ø 9mm) Process connector upside (INSTLLTION CODE '0') Process connector downside (INSTLLTION CODE '1') F04E.EPS Horizontal Impulse Piping Type (Left side Terminal Bo - INSTLLTION CODE '4' - ) Shrouding bolts (Only for TIIS Flameproof type) 193 (7.60) (2.76) (4.92) (3.39) (3.70) 111 (4.37) 68 (2.68) 161 (6.34) 200 (7.87) 27 (1.06) 72 (2.83) 124 (4.88) 47 (1.85) Open to atmosphere (Ø 5mm) F05E.EPS ll Rights Reserved. Copyright 1995, Yokogawa Electric Corporation GS 01C23E01-00E pr. 01,
7 7 Terminal Configuration CHECH METER Connection hook Jumper Terminal Wiring + SUPPLY /BT METER + Power supply and output terminal Eternal indicator(ammeter) terminal Ground terminal Note: When using an eternal indicator, the internal resistance must be 10 or less. BRIN TERMINL Connection hook < Ordering Information > Specify the following when ordering 1. Model, suffi codes, and optional codes 2. Calibration range and units: 1) Calibration range can be specified with range value specifications up to 5 digits (ecluding any decimal point) for low or high range limits within the range of to ) Specify only one unit from the table, Settings when shipped. 3. Select linear or square root for output mode and display mode. Note: If not specified, the instrument is shipped set for linear mode. 4. Select normal or reverse for operation mode Note: If not specified, the instrument is shipped in normal operation mode. 5. Display scale and units (for transmitters equipped with integral indicator only) Specify either 0 to 100 % or engineering unit scale and and Unit for engineering units scale: Scale range can be specified with range limit specifications up to 5 digits (ecluding any decimal point) for low or high range limits within the range of to The range with decimals is available to the third decimal place. 6. Tag Number (if required) < Related Instruments > Power Distributor: Refer to GS 01B04T01-02E or GS 01B04T02-02E BRIN TERMINL: Refer to GS 01C E F06E.EPS < Reference > 1. JIS SUS316L stainless steel; Equivalent to ISI 316L. 2. JIS SUS316 stainless steel; Equivalent to ISI JIS SUS304 stainless steel; Equivalent to ISI JIS SECC Carbon steel. 5. Teflon; Trademark of E.I. DuPont de Nemours & Company (US) for polytetrafluoreoethylene. 6. JIS SUS630 stainless steel; Equivalent to STM Hastelloy; Trademark of Haynes International Inc. 8. JIS SCS14 stainless steel; Equivalent to JIS SUS316 cast stainless steel or STM CF-8M. 9. Other company names and product names used in this material are registered trademarks or trademarks of their respective owners. ll Rights Reserved. Copyright 1995, Yokogawa Electric Corporation Subject to change without notice. GS 01C23E01-00E pr. 01,
General Specifications
General Specifications GS 1C2H1-E Model EJ11W, EJ11N and EJ11Y Diaphragm Sealed Differential Pressure Transmitters [Style: S2] Diaphragm seals are used to prevent process medium from entering directly
More informationGeneral Specifications
General Specifications Model RS and RN Resistance Temperature Sensor GS 06B04D01-00E GENERAL Model RS and RN Resistance Temperature Sensors (RTSs) have a platinum resistance element (Pt 100 or 50 ) in
More informationGeneral Specifications
General Specifications GS 01C31J03-01EN EJA438E Diaphragm Sealed Gauge Pressure Transmitter Diaphragm seal is used to prevent process medium form entering directly into the -sensing assembly of the transmitter,
More informationGeneral Specifications
General Specifications Models RM and RH Resistance Temperature Sensor GS 06B03B01-00E GENERAL Model RM and RH Resistance Temperature Sensors (RTSs) have a platinum resistance element (Pt 100 or 50 ) in
More informationGeneral Specifications
General Specifications EJA118E Diaphragm Sealed Differential Pressure Transmitter Diaphragm seals are used to prevent process medium form entering directly into the -sensing assembly of the differential
More informationGeneral Specifications
General Specifications EJA118E Diaphragm Sealed Differential Pressure Transmitter Diaphragm seals are used to prevent process medium form entering directly into the -sensing assembly of the differential
More informationGeneral Specifications
General Specifications EJA118E Diaphragm Sealed Differential Pressure Transmitter [Style: S2] Diaphragm seals are used to prevent process medium form entering directly into the -sensing assembly of the
More informationGeneral Specifications
General Specifications EJA210E Flange Mounted Differential Pressure Transmitter The high performance flange mounted differential pressure transmitter EJA210E can be used to measure levels of densities
More informationEDR-N8A CS Intelligent Absolute Pressure Transmitter STANDARD SPECIFICATIONS. Accuracy Material Code: Standard,316L Range Accuracy Code
Intelligent Absolute Pressure Transmitter Absolute Pressure Transmitter incorporates semiconductor sensors and a microcomputer and converts measured s to 4 to 20mA DC signal with high accuracy. is suitable
More informationC S. Sanitary Differential Pressure Transmitter with Diaphragm Displacement Device CS Range Code. Accuracy. Note 1)
C S CODE AND SPECIFICATIONS SHEET Sanitary Differential Pressure Transmitter with Diaphragm Displacement Device EDR-N7SD is intelligent transmitter equipped with semiconductor sensers and micro processors.
More informationGeneral Specifications
General Specifications EJX210A Flange Mounted Differential Pressure Transmitter [Style: S2] The high performance flange mounted differential pressure transmitter EJX210A can be used to measure levels of
More informationC S. Differential Pressure Transmitter CS Range Code. Accuracy
C S CODE AND SPECIFICATIONS SHEET Differential Pressure Transmitter EDR-N7P is intelligent transmitter equipped with semiconductor sensers and micro processors. EDR-N7P Range Measuring Code Span Settable
More informationST3000 Series 900 Smart Transmitter Differential Pressure Transmitters
ST3000 Series 900 Smart Transmitter Differential Pressure Transmitters Model STD910/STD920/STD930/STD960/STD921/STD931/STD961 OVERVIEW The ST3000 Smart Transmitter is a microprocessor-based smart transmitter
More informationJUMO dtrans p20 DELTA
Data Sheet 403022 Page 1/9 JUMO dtrans p20 DELTA Differential pressure transmitter Brief description The JUMO dtrans p20 DELTA differential pressure transmitter with HART interface combines maximum precision
More informationThree Way Control Valves
No. SS2-HDT110-0100 Three Way Control Valves Model HDT OVERVIEW The valve model HDT is a three-way control valve for diverting service. It has a small-sized, high-output diaphragm motor which is suitable
More informationRosemount 1810 Flush Mount Pressure Transmitter ROSEMOUNT 1810 FEATURES:
Rosemount 1810 Rosemount 1810 Flush Mount Pressure Transmitter ROSEMOUNT 1810 FEATURES: A cleanable and compact stainless steel design An innovative patented venting configuration that prevents gauge reference
More informationUNIK 5800/5900. Flameproof/Explosion-Proof Pressure Sensing Platform. GE Measurement & Control. High Quality. Features. Bespoke as Standard.
GE Measurement & Control UNIK 5800/5900 Flameproof/Explosion-Proof Pressure Sensing Platform The 5800 and 5900 are compact and rugged versions of the high performance UNIK 5000 pressure sensing platform
More informationSATRON VDt Differential Pressure Transmitter
SATRON VDt differential pressure transmitter belongs to V-transmitter family. The series V transmitters have both analog and smart properties. SATRON VDt is used for -,1kPa...-15 MPa ranges. It is a 2-wire
More informationGeneral Specifications
General Specifications Chemical Cleaning ph Measuring System GS B7A-E General Process ph measuring systems have played an important role in many fields including the chemical, food, metal, and paper pulp
More informationSmart Pressure Transmitter
DOC. NO.: C3500L-E16A Smart Pressure Transmitter with Diaphragm Seal MODEL APT3500L 298-29, GONDAN-RO, GUNPO-SI, GYEONGGI-DO, KOREA 15809 Tel : +82-31-3-6100 Fax : +82-31-29-7200 E-mail: autrol@duon.co.kr,
More informationJUMO dtrans p20. Process pressure transmitter. Type Brief description. Key features. Block diagram
Data Sheet 403025 Page 1/10 JUMO dtrans p20 Process pressure transmitter Brief description The JUMO dtrans p20 pressure transmitter with HART interface combines maximum precision with easy operation. It
More informationMonocrystalline silicon smart differential pressure transmitter. High stability, Diaphragm sealed. Benefits. Application
Monocrystalline silicon smart differential pressure transmitter DRS380 High stability, Diaphragm sealed Detailed Information www.dersensor.com Application the flow of gas, vapor and liquid measurement
More informationSmart Pressure Transmitter
DOC. O.: C3700-L-E16A Smart Pressure Transmitter with Diaphragm Seal MODEL APT3700-L 298-29, GODA-RO, GUPO-SI, GYEOGGI-DO, KOREA 15809 Tel : +82-31-3-6100 Fax : +82-31-29-7200 E-mail: autrol@duon.co.kr,
More informationUNIK Pressure Sensing Platform. GE Sensing & Inspection Technologies. Features
GE Sensing & Inspection Technologies UNIK 5000 Pressure Sensing Platform The UNIK 5000 is a high performance configurable solution to pressure measurement. The use of Druck silicon technology and analogue
More informationThree Way Control Valves
No. SS2-MT100-0100 Three Way Control Valves Model MT OVERVIEW The valve model MT is a three-way control valve for diverting and mixing service. The actuator employed is of a multispring type and has a
More informationDifferential pressure transmitter PASCAL Ci4 Delta P
Differential pressure transmitter PASCAL Ci4 Delta P for diaphragm seal operation, Type series CI4330 Features Application area General process engineering Chemical and petrochemical industry General process
More informationSPANS AND RANGES. Lower Range Limits 150 in. H 2 O ( 38 kpa) 800 in. H 2 O ( 200 kpa)
Specifications 571T, 572T Electronic Differential Pressure Transmitter with Sanitary/ Aseptic Remote Seal Elements ±0.2% of span accuracy Spans from 25 to 800 inches H2O Outstanding temperature stability
More informationSmart Pressure Transmitter
DOC. NO.: C3100L-E16B Smart Pressure Transmitter with Diaphragm Seal MODEL APT3100L DUON System Co., Ltd. 298-29, GONDAN-RO, GUNPO-SI, GYEONGGI-DO, KOREA 15809 Tel : +82-31-3-6100 Fax : +82-31-29-7200
More informationCDT1000 series QUICK FLOW. Digital Flowmeter for Air Conditioning Application OUTLINE FEATURES STANDARD SPECIFICATION
QUICK FLOW CDT1 series Digital Flowmeter for ir Conditioning pplication OUTLINE CDT1 is a new series of flowmeter which combines a multidigital indicator with a pitot tube. CDT1 detects the differential
More informationSATRON VT Pressure Transmitter
SATRON VT pressure transmitter belongs to the series V-transmitters. SATRON VT is used for 0-1.4 kpa...0-100 MPa ranges. It is a 2-wire transmitter with HART standard communication. In pressure measuring
More informationDL 01. Battery Powered Precision Digital Gauge for Leak Testing. Stainless Steel Sensor. class 0.05
DL 0 Battery Powered for Leak Testing Stainless Steel Sensor class 0.05 Nominal pressure from 0 00 mbar up to 0... 00 bar Special characteristics modular sensor concept data logger graphic display stainless
More informationUser s Manual. Model MLD Loop Powered Process Indicator IM 61A01A01-01E-A IM 61A01A01-01E-A. 4th Edition
User s Manual Model MLD Loop Powered Process Indicator 4th Edition 1. PREFACE The Model MLD field mounted indicator receives a DC current signal from electronic transmitters and indicates process measurement
More informationDifferential pressure transmitter PASCAL Ci4 Delta P
Differential pressure transmitter PASCAL Ci4 Delta P for general application, Type Series CI4300 Features Differential pressure transmitter with metallic diaphragm High-resolution graphic display with
More informationDifferential pressure transmitter PASCAL Ci4 Delta P
Differential pressure transmitter PASCAL Ci4 Delta P for high static working pressure, PN 160, Type series CI4340 Features Simultaneous display of differential pressure and static pressure Long-term stability
More informationPressure transmitter PASCAL CV4
Pressure transmitter PASCAL CV4 with threaded connection, Type series CV4100 Features Application area Pharmaceutical industry Food industry Biotechnology General process technology Compact case of stainless
More information2-Color Display Digital Pressure Switch
-Color Display Digital Pressure Switch (F)/(H) Series Stainless diaphragm Oil-free (Single-layer diaphragm structure) Sensor unit: Stainless steel 630 Fitting parts: Stainless steel 304 The sensor unit
More informationJUMO dtrans p20. Process pressure transmitter. Brief description. Special features. Block diagram. Approvals/approval marks (see "Technical data")
Page 1/15 JUMO dtrans p20 Process pressure transmitter Brief description The device with the HART interface combines maximum precision with simple operation. It is used to measure the system pressure of
More informationUser s Manual. Model MLA & MLD Loop Powered Process Indicators. Model MLD (Digital) Model MLA (Analog)
User s Manual Model MLA & MLD Loop Powered Process Indicators Model MLD (Digital) Model MLA (Analog) 1. PREFACE The Model MLA and MLD field mounted indicators receive DC voltage or current signals by electronic
More informationGeneral Specifications
General Specifications DO0G Sensor for Dissolved Oxygen Analyzer GS 2J05D0-0E GENERA The DO0G sensor for dissolved oxygen is designed for use in water treatment plants such as sewage treatment works, effluent
More informationGeneral Specifications
eneral Specifications Model TB Surface Scattering Light Meter S 12E04A02-01E eneral There have been increasing demands for both industrial use and portable water of good quality because of rapid industrial
More informationSmart Pressure Transmitter
DOC. NO.: C3200L-E16B Smart Pressure Transmitter with Diaphragm Seal MODEL APT3200L DUON System Co., Ltd. 298-29, GONDAN-RO, GUNPO-SI, GYEONGGI-DO, KOREA 15809 Tel : +82-31-3-6100 Fax : +82-31-29-7200
More informationGeneral Specifications
General Specifications DO30G Sensor for Dissolved Oxygen Analyzer GS 2J05D03-0E GENERA The DO30G sensor for dissolved oxygen is designed for use in water treatment plants such as sewage treatment works,
More informationGeneral Specifications
General Specifications Model DT450G Dust Monitor GENERAL Powder is used in many industries including ceramics,cement, chemicals, pharmaceutical and food. In their processes, powder is collected in order
More informationModel Y/13FA, Y/13FEA and Y/15FA Pneumatic Flange Mounting Differential Pressure Transmitters
User s Manual Model Y/13FA, Y/13FEA and Y/15FA Pneumatic Flange Mounting Differential Pressure Transmitters 5th Edition Model Y/13FA, Y/13FEA and Y/15FA Pneumatic Flange Mounting Differential Pressure
More informationMagneW Neo+ Two-wire Electromagnetic Flowmeter Integral type TIIS Explosion-protected Apparatus
MagneW Neo+ Two-wire Electromagnetic Flowmeter Integral type TIIS Explosion-protected Apparatus OVERVIEW The MagneW Neo+ is a high performance two wired electromagnetic flowmeter based on field proven
More informationSeries ZSE30/ISE30. High Precision, 2-color Display Digital Pressure Switch 25 M ISE30 01 ZSE M. How to Order. For positive pressure
High Precision, Series SE30/ISE30 How Order Option 1 Without lead wire Lead wire with connecr (Lead wire length: 2 m) L For positive pressure For vacuum/low pressure ISE30 01 SE30 01 25 M 25 M 01 R 1/8
More informationPRESSURE TRANSMITTER PYRP-28 INDUSTRIAL & INTRINSICALLY SAFE PRESSURE TRANSMITTER PRESSURE TRANSMITTER
PRESSURE PYRP-28 INDUSTRIAL & INTRINSICALLY SAFE PRESSURE The PYRP-28 pressure transmitter is suitable for the measurement of pressure, vacuum and absolute pressure of gases, vapours and liquids for industrial
More information압력트랜스미터 Model ADP9000 Series
ALIA PRODUCT 압력트랜스미터 Model ADP9000 Series GEERAL ADP9000 series is a digital differential pressure transmitter designed for industrial pressure measurement applications. The ADP9000 offer Configurations
More information2-colour display. Digital Pressure Switch. Stainless diaphragm Oil-free (Single-layer diaphragm structure) IP65 compliant
-Colour Display Digital Pressure Switch Stainless diaphragm Oil-free (Single-layer diaphragm structure) Sensor parts: Stainless steel 6 Fitting parts: Stainless steel 4 The sensor and fitting parts can
More informationSATRON VVFe Pressure Transmitter
SATRON VVFe pressure transmitter belongs to Vtransmitter family. SATRON VVFe is used for 0 4 kpa...0500 kpa ranges. It is a 2wire transmitter with HART standard communication. SATRON VVFe pressure transmitter
More information2010TC for Differential Pressure, Pressure and Temperature (Mass Flow)
Technical data 2 Principle of Operation and Construction The transmitter has a modular design and consists of the differential pressure sensor module with an integrated electronic matching unit, an amplifier
More informationRosemount 3152N Nuclear Qualified Pressure Transmitter
Product Data Sheet Rosemount 3152N Nuclear Qualified Pressure Transmitter Rosemount 3152N INDUSTRY LEADING PERFORMANCE Qualified per: o IEEE Std 323-1974/1983/2003 o IEEE Std 344-1975/1987/2004 6.5 Mrad
More informationPiezoresistive single crystal silicon pressure transmitter
Product introduction Description Piezoresistive single crystal silicon pressure transmitter 305PI TSD single crystal silicon pressure transmitter is a high performance pressure transmitter with international
More informationINTERPLANT STANDARD - STEEL INDUSTRY. Specification for Smart Pressure & Differential Pressure Transmitter
INTERPLANT STANDARD - STEEL INDUSTRY IPSS Specification for Smart Pressure & Differential Pressure Transmitter Corresponding IS does not exist IPSS: 2-07-104-15 1. Scope 1.1 This Interplant Standard covers
More informationDM01. Battery Powered Precision Digital Gauge. Stainless Steel Sensor. class 0.05
Battery Powered Stainless Steel Sensor class 0.05 Nominal pressure from 0 00 mbar up to 0... 00 bar Special characteristics modular sensor concept data logger graphic display stainless steel housing Ø
More information2SGT. Electronic Pressure Instrument. Three Separate Functions in a Single Loop-Powered Device
2SGT Electronic Pressure Instrument Three Separate Functions in a Single Loop-Powered Device Switch Two Independent, Programmable SPST Solid State Relays Program switch open and close values in engineering
More information2600T Series Pressure Transmitter
Data Sheet 2600T Series Pressure Transmitter Model 261GS Gauge Model 261AS Absolute standard overload Base accuracy: ±0.15 % Span limits 0.3 to 60000kPa; 1.2inH 2 O to 8700psi 0.3 to 3000kPa abs; 2.25mmHg
More informationGeneral Specifications
General Specifications GS 01E08B01-00E Models CSG/S/SC and 200SG/S/SC Capacitance Magnetic Flowmeter DMG C magnetic flowmeter is excellent at measurement in ultra-low conductivity fluids down to 0.01µS/cm,
More informationEGM1100C MAGMAX. Compact Electromagnetic Flowmeter GENERAL FEATURES STANDARD SPECIFICATION. General Specification
EGMC Compact Electromagnetic Flowmeter GENERA MAGMAX EGMC is the compact type electromagnetic flowmeter with a converter EGC mounted integrally on a primary head EGS lined with fluorocarbon resin PFA.
More informationModel 266HSH Gauge pressure transmitter low power consumption (1 to 5 V DC and HART)
Data Sheet DS/266HSH/LowP-EN Rev. B Model 266HSH Gauge pressure transmitter low power consumption (1 to 5 V DC and HART) Engineered solutions for all applications Measurement made easy Base accuracy 0.15
More informationRosemount 3152K Nuclear Qualified Pressure Transmitter
Nuclear Qualified Pressure Transmitter INDUSTRY LEADING PERFORMANCE Qualified per KTA 3505 Mild Environment Qualifications 50 kgy (5 Mrad) TID Gamma Radiation Vibration to 5g seismic and 8g APC LOCA/HELB
More informationSITRANS P measuring instruments for pressure
Overview Siemens AG 009 Supplementary electronics for 4-wire connection Design Dimensions (W x H x D) in mm (inch) Electrical connection 80 x 10 x 60 (3.15 x 4.7 x.36) Screw terminals (Pg 13.5 cable inlet)
More informationJUMO dtrans p02. Pressure transmitter. General application. Approvals/marks of conformity. Data Sheet Page 1/6. II 1/2G Ex ia IIC T6 Ga/Gb
sales@jumo.co.uk info@jumo.us Data Sheet 404385 Page 1/6 JUMO dtrans p02 Pressure transmitter II 1/2G Ex ia IIC T6 Ga/Gb General application The pressure transmitter Type JUMO dtrans p02 is used to measure
More informationM3500 Industrial Pressure Transmitter
M3500 Industrial Pressure Transmitter The M3500 is a high accuracy industrial pressure transmitter featuring HART communications and a cast aluminum enclosure for indoor or outdoor use. Typical output
More informationEccentric Rotary Control Valve (For size 1 to 4 inches)
No. SS2-VFR100-0200 FloWing Eccentric Rotary Control Valve (For size 1 to 4 inches) Model VFR OVERVIEW The eccentric rotary control valve, FloWing (model VFR), consists of a straight-through valve body
More informationSmart Valve Positioner 700 Series with HART Communication Protocol
No. SS2-AVP702-0100 Smart Valve Positioner 700 Series with HART Communication Protocol OVERVIEW The Smart Valve Positioner 700 Series (model number: AVP7**) not only inherits the reliability of the core
More information2-Color Display High-Precision Digital Pressure Switch
2-Color Display High-Precision Digital Pressure Switch Settings can be copied to up to 1 slave sensors at once. The settings of the master sensor can be copied to the slave sensors. Reduced setting efforts
More informationST3000 Ace Smart Transmitter Sanitary Differential Pressure / Pressure Transmitters
ST3000 Ace Smart Transmitter Sanitary Differential Pressure / Pressure Transmitters Model JTC929A/JTC940A, JTE929A/JTE930A OVERVIEW The Food and beverage industry and fermentation industry require equipment
More informationOperating Instructions Vaccon VDS-1000 Solid State Combination Vacuum Switch/Sensor w/ Digital Display
Operating Instructions Vaccon VDS-1000 Solid State Combination Vacuum Switch/Sensor w/ Digital Display Installation The VDS-1000 combines either two (2) low voltage, high side or low side, switched outputs
More informationSet value (Threshold value) Bottom value. *2 Further reduced by approx. 60% in power-saving mode (For 20 series)
3-Screen Display High-Precision Digital Pressure Switch New Added Variations! For general fluids IP65 2 outputs Analog output Setting is possible while checking Main screen the measured value. Sub screen
More informationSmart Valve Positioner 700 Series with HART Communication Protocol
No. SS2-AVP702-0100 Smart Valve Positioner 700 Series with HART Communication Protocol OVERVIEW The Smart Valve Positioner 700 Series (model number: AVP7**) not only inherits the reliability of the core
More informationSATRON VTe pressure transmitter
SATRON VTe pressure transmitter belongs to the series V-transmitters which will have both analog and smart properties. SATRON VTe is used for 0-4 kpa...0-00 MPa ranges. The transmitter communicates in
More informationABB Instrumentation. 50T Series Transmitters Model 54G/A gauge/absolute pressure transmitter for sanitary use. Specification sheet
Specification sheet 50T Series Transmitters Model 54G/A gauge/absolute pressure transmitter for sanitary use Ranges : - 100 to 4000 kpa - 1 to 40 bar - 14.5 to 600 psi Base accuracy : 0.2%(BFSL) Piezoresistive
More informationFIELD DEVICES CONTROLLERS
FIELD DEVICES CONTROLLERS Product Specifications 43AP Pneumatic Indicating Controllers These instruments indicate and control pressure, temperature, vacuum, and differential pressure. They provide process
More informationProduct presentation SITRANS P310
Product presentation SITRANS P310 Unrestricted / Siemens 2016. All Rights Reserved. usa.siemens.com/pressure SITRANS P family Page 2 SITRANS P pressure transmitter Single range transmitters for general
More informationPitoMaster FPD550 Compact averaging pitot flowmeter. Economical flow metering solutions for gases, liquids and steam
Data sheet DS/FPD550 EN Rev. C PitoMaster FPD550 Compact averaging pitot flowmeter Economical flow metering solutions for gases, liquids and steam Compact flowmeter with integral transmitter, manifold
More informationSeries 10-ZSE40A(F)/10-ISE40A
Series 10-ZSEA(F)/10-ISEA RoHS 2-Color Display High Precision Digital Pressure Switch How to Order For positive pressure Clean series For vacuum/ compound pressure 01 N01 W1 10 Rated pressure range ISEA
More informationAMETEK Model PPC Series Electronic Pressure Calibrator
Specification Sheet CP-2176-0399 March 1999 Issue 1 AMETEK Model PPC Series Electronic Pressure Calibrator Two Models, Two Accuracies - PPC Accuracy +0.05% of Full Scale +1 LSD - PPCE Accuracy +0.04% of
More informationUser's Manual Models SE100MJ/NJ and SE200MJ/NJ Integral Type Magnetic Flowmeter
User's Manual Models SE100MJ/NJ and SE200MJ/NJ Integral Type Magnetic Flowmeter Manual Change No. 09-001-5E Please use attached sheets for the pages listed below in (10th). Page Page 10-2 EMC Conformity
More informationTEK-B AR 3110A. Differential Pressure Transmitter. Flow Level Temperature Pressure Valves Analyzers Accessories TekValSys PRESSURE
Technology Solutions TEK-B AR 3110A Differential Pressure Transmitter PRESSURE www.tek-trol.com Flow Level Temperature Pressure Valves Analyzers Accessories TekValSys Introduction The Tek-Bar 3110A Differential
More informationEccentric Rotary Control Valve (For size 6 to 12 inches)
No. SS2-VFR100-0100 OVERVIEW FloWing Eccentric Rotary Control Valve (For size 6 to 12 inches) Model VFR The eccentric rotary control valve, FloWing (model VFR), consists of a straight-through valve body
More informationEGM5300C MAGMAX. Compact Electromagnetic Flowmeter GENERAL FEATURES STANDARD SPECIFICATION. General Specification
MAGMAX EGM53C Compact Electromagnetic Flowmeter GENERAL MAGMAX EGM53C is a combination of EGS5 primary head with Ceramic measuring tube and high performance converter EGC3. EGM53C with high durability
More informationSeries 60. New Smart Positioner. Compact design Convenient & powerful function Enhanced reliability
Series 60 New Smart Positioner Compact design Convenient & powerful function Enhanced reliability J Flow Controls, LLC 14 De Camp Cincinnati, OH 45216 Phone: 513-731-2900 Fax 513-731-6939 www.jflowcontrols.com
More informationGeneral Specifications
General Specifications Model UYF200, UYF21 Ultrasonic Vortex meter OVERVIEW When a vortex shedder is installed in a process flow line, the regular Karman vortex street is shed at the downstream of the
More informationPressure transmitter JUMO dtrans p02
JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 609 Fulda, Germany Postal address: 605 Fulda, Germany Phone: +49 661 600-0 Fax: +49 661 600-607 e-mail: mail@jumo.net Internet: www.jumo.net JUMO
More informationSmart Displacement type Level Transmitter
No. SS-SLX100-0100 Smart Displacement type Level Transmitter model SLX OVERVIEW The SLX series is a complete line of highly accurate and reliable high-performance torque tube type displacement level transmitters
More informationSITRANS P measuring instruments for pressure
Overview The is a digital pressure transmitter for gage and absolute pressure All conventional thread versions are available as process connections. In addition, various hygiene-based connections and flange
More informationSeries ZSE30/ISE30. High Precision, 2-color Display Digital Pressure Switch. With One-touch fittings are newly introduced. PSE
High Precision, 2-color Display Digital Pressure Switch Series SE30/ISE30 SE ISE PSE I SE3 PS I SE 1 2 SP ISA2 IS SM PF2 IF Data With One-touch fittings are newly introduced. Straight type Elbow type 16-2-1
More informationPortable pressure calibrator, Wally Box III Model CPH7600
Calibration technology Portable pressure calibrator, Wally Box III Model CPH7600 WIKA data sheet CT 17.01 Applications Calibration service companies and service industry Measurement and control laboratories
More information3-step setting. 2-Color Display High-Precision Digital Pressure Switch. Series ZSE30A(F)/ISE30A. Added vacuum range.
2-Color Display High-Precision Digital Pressure Switch Series ZSE3A(F)/ISE3A RoHS Can copy to up to 1 switches simultaneously. The settings of the master sensor can be copied to the slave sensors. Reducing
More informationTemperature Indicating Controller
\ KF Series Temperature Indicating Controller Model KFT OVERVIEW The KF Series instruments are field-installed type of pneumatic indicating controllers which are used to measure and control the various
More informationSmart Electromagnetic Flowmeter Detector for Sanitary use
MagneW3000 PLUS Smart Electromagnetic Flowmeter Detector for Sanitary use Model MGS28U OVERVIEW The MagneW3000 PLUS Smart Electromagnetic Flowmeter for Sanitary use is a high-performance and highly-reliable
More informationIGP10, IGP20 Intelligent Gauge Pressure Transmitters IAP10 Intelligent Absolute Pressure Transmitter
, Intelligent Gauge Pressure Transmitters Intelligent Absolute Pressure Transmitter 1 for compact light weight and direct-to-process mounting (bracket optionally available), bracket mounted, for lower
More informationDifferential Pressure Gauges (701P Series)
Applications Equipped two Process Connections Indicating low and high pressure Measuring differential pressure as well as liquid or flow levels Recommended to use 3-way & 5-way valve manifold Pressure
More informationCV3000 Series Low-Noise Cage type Control Valve Model ACN
No. SS2-ACN110-0100 CV3000 Series Low-Noise Cage type Control Valve Model ACN OVERVIEW The model ACN low-noise cage type control valves are designed to reduce acoustic noise in services of compressible
More informationRemote-sealed type of Differential Pressure Transmitters
AT9000 Advanced Transmitter Remote-sealed type of ifferential Pressure Transmitters OVERVIEW AT9000 Advanced Transmitter is a microprocessor-based smart transmitter that features high performance and ecellent
More informationElectric Top-Guided Single-Seated Control Valves
No. SS2-AGV200-0300 CV3000 Alphaplus series Electric Top-Guided Single-Seated Control Valves Model AGVB / AGVM OVERVIEW The CV3000 Alphaplus range of top-guided single-seat control valves features a compact
More informationSafir-M digital. Features. LCD indicator and controls. Industries. Applications
Features Reference accuracy, % FS 0.1 0.15 0.25 0.5 (draft pressure) Turndown 1:25 Output 4 20 ma, 0 5 ma Linear (increasing or decreasing) Square root (differential pressure) Damping (optional), s 0.5
More informationLevel Measurement. Continuous level measurement - Capacitance transmitters SITRANS LC500. 5/282 Siemens FI Overview.
SITRANS LC00 Overview Configuration Installation Build up of material or condensation in active shield area does not affect switch operation. SITRANS LC00 is an inverse frequency shift capacitance level
More informationAP ATEX AIRPOWER POSITIONERS AP2000 FEATURES AP1000 & AP1200 FEATURES OPTIONS OPTIONS
AP1000-2000 Airpower positioners are a robust range of rotary or linear valve positioners in AP1000 electro-pneumatic (4-20mA), AP1200 pneumatic (3-15 psi) or AP2000 programmable smart type. Designed to
More information