G1849 Eyewash, Deck Mounted, AutoFlow 90º Swing-Down

Transcription

1 Eyewashes G1849 Eyewash, Deck Mounted, AutoFlow 90º Swing-Down G1849LH-L G1849LH G1849LH-R G1849L G1849 G1849R Model G1849LH-L Shown Application: AutoFlow eyewash for mounting on counter. Spray heads swing down from storage to operational position, activating water flow. Available in a variety of spray head configurations to minimize obstructions at a sink. Note: If unit is not installed at a sink, floor drain should be provided underneath unit to prevent accumulation of water on floor. Spray Head Assembly: Two GS-Plus spray heads. Each head has a flip top dust cover, internal flow control and filter to remove impurities from the water flow. Valve: 1/2" IPS plug-type valve with Teflon coated O-ring seals. Swinging head assembly down from storage to operational position opens orifice and activates water flow. Unit remains in operation until spray head assembly is returned to storage position. Strainer: Unit is furnished with in-line strainer to protect valve and spray heads from debris in water line. Mounting: Valve is installed in Type 316 stainless steel housing. Unit mounts on countertop behind sink. Furnished with mounting hardware for securing unit to counter. Construction: Polished chrome plated brass. Supply: 1/2" NPT male inlet. Sign: ANSI-compliant identification sign. Quality Assurance: Unit is completely assembled and water tested prior to shipment. Available Options TMV G3600LF thermostatic mixing valve precisely blends hot and cold water to deliver warm (tepid) water as required by ANSI Z Refer to Tempering Units section for complete technical and product selection information.

2 Eyewashes G1849 Eyewash, Deck Mounted, AutoFlow 90º Swing-Down G1849LH-L G1849LH G1849LH-R G1849L G1849 G1849R 6 1/2" (165mm) (2) GS-PLUS SPRAY HEADS 1 3/4" (45mm) 7/8" (22mm) DETAIL OF MOUNTING PINS Ø3/16" 9/32" DEEP (2 PLCS.) STORAGE POSITION Ø7/8" (22mm) CHROME PLATED BRASS SUPPLY ARM ACTIVATION POINT 63 15" (381mm) 1-15/64" (31mm) 1 3/4" (45mm) CHROME PLATED BRASS ELBOW FITTING 13" (331mm) OPERATIONAL POSITION /2" (38mm) 2-45/64" (69mm) 1/2" IPS MOUNTING SHANK WITH LOCKNUT AND WASHER IN-LINE STRAINER (SHIPPED LOOSE; INLET MAY BE POSITIONED AS DESIRED) NOTES: 1. SWINGING OUTLET HEAD ASSEMBLY DOWN 96 DEGREES FROM VERTICAL TO HORIZONTAL POSITION ACTIVATES WATER FLOW. 2. EACH GS-PLUS SPRAY HEAD HAS A "FLIP-TOP" DUST COVER, INTERNAL FLOW CONTROL AND FILTER TO REMOVE IMPURITIES FROM THE WATER FLOW. 3. UNIT MOUNTS INTO COUNTERTOPS UP TO 1 1/2" THICK. BASE OF UNIT HAS PINS TO PREVENT UNIT FROM TURNING ON COUNTER. 4. UNIT IS FURNISHED WITH IN-LINE STRAINER TO PROTECT SPRAY HEADS AND VALVE COMPONENTS FROM DEBRIS IN WATER LINE. 5. VALVE BEGINS TO OPEN AT "ACTIVATION POINT" SHOWN ABOVE. 2 3/8" (60mm) 1/2" NPT FEMALE INLET this space for architect/engineer approval Sign Included Due to continuing product improvement, the information contained in this document is subject to change without notice. All dimensions are ± 1/4" (6mm).

3 Parts List Swing-Type Eyewashes and Eye/Face Washes Each spray head head features: Tough polypropylene plastic construction Highly visible integrated nylon dust cover Easily accessible 1.8 GPM (GS-Plus ) or 3.2 GPM (FS-Plus ) flow controls. Dense (60 pore per inch) polyurethane filter Unique design provides a consistently soft, full spray of water across a range of working pressures from 30 to 100 PSI Item Part Number Description A AP GS-Plus Spray Head (assembled) B AP R Dust Cover and Cap Assembly C R 60 PPI Polyurethane Filter D R 1.8 GPM Flow Control E AP FS-Plus Spray Head (assembled) F AP R Dust Cover and Cap Assembly G R 60 PPI Polyurethane Filter H R 3.2 GPM Flow Control A E Note: If experiencing any issues with the rotating valve assembly, please contact the factory. B F C G IMPORTANT In order to operate properly, the flow control must be inserted into the body concave end first. D H

4 Parts List In-Line Strainer To perform weekly cleaning of the strainer: 1. Unscrew the strainer bonnet (a). 2. Inspect the o-ring (b) for for damage. Replace if needed. 3. Remove cylindrical screen (c) and rinse under clean water. Gently rub the screen until all debris has been removed. 4. Carefully reinsert screen into the counterbore within the strainer body (should fit snugly). 5. Replace strainer bonnet and test for proper operation of strainer and eye wash. Important: All emergency equipment must be inspected and tested at least weekly to ensure proper operation. On units equipped with an in-line strainer, weekly inspection should also include checking the strainer for accumulation of debris or foreign matter. Such debris can impair the flow of water through the strainer and prevent the eye wash from functioning properly. AP In-Line Strainer Assembly A B RK Repair Kit for Inline Strainer consisting of bonnet, O-Ring and 50 Mesh Cylindrical Screen C

5 A. EW-18* Deck mounted AutoFlow swivel eye wash less bowl with ½ IPS plug-type valve with Teflon coated O-ring seals and stainless steel enclosure. Supplied with inline strainer to prevent debris from affecting the valve. Unit shall have (2) polypropylene GS Plus spray heads with integral flip-top dust covers, filters and 1.8-GPM flow control orifices mounted on a chrome plated brass eyewash assembly (Specify spray head configuration). Activate valve by rotating 90 from stored position. Unit shall include ANSI compliant sign. B. Performance: Unit shall be fully factory assembled and hydrostatically tested to meet or exceed ANSI Z , and come with a full 2-year warranty. C. Fixture: Guardian Equipment G1849