Replacement Parts. Model 4450 Jaw Crusher. page

Transcription

1 Replacement Parts Model 4450 Jaw Crusher page

2 Your equipment serial number and order number have been recorded in the space below. Please include these numbers when requesting service or ordering parts. KOLBERG-PIONEER, INC. JOB ORDER MODEL 4450 Jaw S/N MANUFACTURED BY KOLBERG-PIONEER, Inc. YANKTON, SD, U.S.A. Serial Number Plate Location Rear Front Use IB229 for Operation Manual page

3 INTRODUCTION This bulletin contains replacement parts listings for your equipment. In most cases an illustration is used to identify the assembly, with each illustration is a parts list identifying serviceable parts. In some cases no illustration is available or required and just a parts list is shown. When a part name is indented, it means the serviceable item is a part of the item under which it is listed. The quantity of parts shown with these indented items are for the assembly only and not the entire machine. EXAMPLE: This item contains these items. Ref. No. Description Part No. Qty. 1 Coupling Assembly AEP Coupling Flange Bushing Quantity for machine Quantity for assembly Abbreviations and Symbols Used In This Parts Book * See notes at bottom of page N/S Not Serviced X Parts not exactly as shown O/E P/N Optional Equipment Part Number KOLBERG-PIONEER, INC. reserves the right to make changes or add improvements to its products at anytime, without incurring any obligation to make such changes on previously manufactured equipment. Although care has been taken to assure the accuracy of this publication, KOLBERG- PIONEER, INC. does not assume any liability for errors or omissions. page

4 CONTENTS ORDERING PARTS... 1 JAW CRUSHER BASE... 2 WEDGE ADJUST ASSEMBLY... 3 WEDGE ADJUST WEAR LINERS AND TOGGLE PLATE... 4 TENSION ROD ASSEMBLY... 5 FLYWHEEL ASSEMBLY DRIVE... 6 FLAT FLYWHEEL ASSEMBLY... 7 WEAR LINERS JAW WEDGE AND JAW PLATES PITMAN / SHAFT ASSEMBLY HYDRAULIC ADJUST ASSEMBLY page

5 ORDERING PARTS We want to service your equipment promptly and accurately. Your observance of the instructions below will greatly aid us in giving you such parts service. When ordering parts be sure you supply the following: (A) Part Numbers, (B) Descriptions, (C) Quantities (D) Serial Numbers, (E) Shipping Instructions. (A) PART NUMBERS Compare part number found on the part with part number in the parts book, whenever possible. When part number is not available, give full description and where used. (B) DESCRIPTIONS Use Part Book descriptions in addition to part numbers. Most structural parts, such as framework, gussets, braces etc., are not listed. To order such parts, give size, shape (channel, angle, plate, etc.), and location, as related to units or groups identified in the parts book. (C) QUANTITIES Be specific. State exactly how many of each part are required. Avoid the use of words like sets or complete. (D) Identify your equipment by Serial Number whenever possible. (E) SHIPPING INSTRUCTIONS Specify name, shipping point, and mail address for notification if different than shipping point. State whether freight, express, parcel post or other handling is desired. Confirm telephone orders in writing. INSPECTION Shortages or damage should be noted by the carrier agent at time material is accepted. Shipper s responsibility ceases upon delivery of shipment to carrier in good order. Claims for damage or loss can likely be collected with proper notation on delivery receipt. ORDER EARLY Make periodical inspections of equipment. Wear parts can be ordered by mail ahead of actual replacement time. Save on telephone expense and have material on hand when needed. page 1

6 JAW CRUSHER BASE 2 1 Ref. No. Description Part No. Qty. 1 Base, Jaw Bolt Washer Shear Block page 2

7 page 3 WEDGE ADJUST ASSEMBLY

8 WEDGE ADJUST WEAR LINERS AND TOGGLE PLATE page 4

9 page 5 TENSION ROD ASSEMBLY

10 FLYWHEEL ASSEMBLY DRIVE SECTION A-A ROTATION WASHER page 6

11 FLAT FLYWHEEL ASSEMBLY SECTION A-A ROTATION WASHER page 7

12 WEAR LINERS page 8

13 WEAR LINERS page 9

14 JAW WEDGE AND JAW PLATES page 10

15 page 11 JAW WEDGE AND JAW PLATES

16 PITMAN / SHAFT ASSEMBLY B FLOAT SIDE 19 FIXED SIDE B DETAIL B for bolts see jaw crusher base page SECTION D-D 25 page 12

17 PITMAN / SHAFT ASSEMBLY ITEM PART NO BB WSC WSC WSC L WSC WSC CP WSC WSC WSC CP BB AA ECCENTRIC SHAFT ASSY QTY DESCRIPTION 1 PITMAN ASSY 1 WEAR PLATE 8 HEX CAPSCREW 3/4 8 WASHER;3/4 8 LOCKNUT 1 MOVING JAW KEY 1 HEX CAPSCREW 3/4 1 LOCKNUT;3/4 2 PULL-OFF COLLAR 2 BEARING 2 BEARING COVER 1 FIXED END INNER COVER 1 FLOATING END INNER COVER 2 BEARING HOUSING 2 BEARING 2 ADAPTOR SLEEVE, BEARING 2 LOCKNUT 2 LOCKPLATE 2 SPACER COLLAR 10 HEX CAPSCREW 5/8 10 LOCKWASHER; 5/8 16 LOCKWASHER; 3/4 16 CAP SCREW; 3/4 1 BRG COVER; OUT, FXD 1 BRG COVER; OUT, FLT 2 SHAFT FLINGER COLLAR 2 SHAFT SPACER FOR HOLDING FLYWHEEL 2 FLYWHEEL SPACER 2 LOCKNUT 2 LOCKWASHER 2 LUBE FITTING 2 PIPE PLUG, 64 CAPSCREW; 5/8 4 SETSCREW; 5/8 64 BRASS WASHER; 5/8 35' STAINLESS STEEL WIRE 2 STR KEY 1 ECC. SHAFT, W/LOCKNUTS 2 SHAFT FLINGER COLLAR 2 CLOSURE BAND ON PILLOW BLOCK page 13

18 HYDRAULIC ADJUST ASSEMBLY page 14

19 HYDRAULIC ADJUST ASSEMBLY POWER UNIT Replaceable Parts for Motor Motor Pump Coupling Replaceable Parts for Valve Handle page 15

20 For Service For Par arts ts KPI -Toll free ( ) Fax ( ) JCI - Toll free ( ) Fax KPI - Toll free ( ) Fax JCI ( ) Fax /07 page