MODEL P Parts List UNIT SERIAL NUMBER MANUAL NUMBER: AB-F EFFECTIVE 06/2016

Transcription

1 Parts List UNIT SERIAL NUMBER MANUAL NUMBER: EFFECTIVE 06/ TH AVE SW CEDAR RAPIDS, IA PHONE (319) FAX (319) Copyright 2007 Highway Equipment Company, Inc.

2 TABLE HEADER OF CONTENTS CONTENTS Table of Contents 2 Instructions for Ordering Parts 4 Body 5 Inverted V 5 Screens 6 Screens - Flip-Up 7 Conveyor 8 Conveyor Drive 8 Conveyor Idler 10 #1 Conveyor Chain 11 Feedgate 12 Spinner 14 Spinner Hopper 14 Spinner Hopper - Extended 16 Spinner Hopper - Flip-Up 18 Engine Drive 20 Electric Clutch 20 Engine - 11 HP Honda 22 Engine HP Briggs & Stratton 24 Engine Hood 26 Guards 27 Control Panel & Connections 28 Hydraulic Drive 31 Direct Drive 31 Single Hydraulic Drive 32 Dual Hydraulic Drive 34 Hydraulics - Single 36 Hydraulics - Dual 38 Pedestal Mount Kit 40 Lights 41 Decals 42 Mounting Kit 44 2

3 NOTES This page is intentionally left blank. 3 NOTES

4 INSTRUCTIONS HEADER FOR ORDERING PARTS Order from the AUTHORIZED DEALER in your area. 1. Always give the pertinent model and serial number. 2. Give part name, part number and the quantity required. 3. Give the correct address to where the parts are to be shipped, and the carrier if there is a preference. Unless claims for shortages or errors are made immediately upon receipt of goods they will not be considered. Any part returns should be directed through the dealer from which they were purchased. When broken goods are received, a full description of the damage should be made by the carrier agent on the freight bill. If this description is insisted upon, full damage can always be collected from the transportation company. No responsibility is assumed for delay or damage to merchandise while in transit. Our responsibility ceases upon delivery of shipment to the transportation company from whom a receipt is received showing that shipment was in good condition when delivered to them, therefore, claims (if any) should be filed with the transportation company and not with Highway Equipment Company. If your claims are not being handled (by the transportation company) to your satisfaction, please call our Product Sales & Support Department at Highway Equipment Company at for assistance. In the parts list the following symbols and abbreviations stand for: * - Not Shown AR As Required CS Carbon Steel SS Stainless Steel NS Not Serviced PARTS ORDERING LIST PARTS The parts listed under the different steel types (CS, 409 SS and 304 SS) are for that type of unit and do not necessarily mean the part is made of that type of steel. 4

5 BODY HEADER INVERTED V CS SS V Inverted 7 Unit V Inverted 8 Unit X1 V Inverted 9 Unit V Inverted 10 Unit Cap Screw 3/8 x Washer Lock 3/ Nut Hex 3/8 4 5

6 SCREENS HEADER Screen 7 Wldmt Screen 8 Wldmt Screen 7 HD Wldmt Screen 8 HD Wldmt Screen 9 HD Wldmt Screen 10 HD Wldmt 1 6

7 SCREENS HEADER - FLIP-UP Hardware Kit, Includes Screen Wldmt 3 AR Screen Wldmt 4 AR Screen Wldmt 5 AR Pivot Wldmt Cap Screw 3/8-16 x 3-1/ Nut Lock 3/ Clamp Screen Cap Screw 3/8-16 x 1-1/ Washer Lock 3/ Nut Hex 3/8 2 AR - As Required 7

8 CONVEYOR HEADER CONVEYOR DRIVE 20,21,22, ,28, ,28,29, ,28, ,27, ,8 2,5,6 16,17, ,25 9 CS SS Shaft Drive Sprocket Drive Bearing Flange Coupling Drive Shaft, Engine & Hyd Coupling Drive Shaft, Direct Hyd Screw Set 4 8

9 CONVEYOR HEADER DRIVE CONTINUED CS SS Key - Square Pin Clevis, Engine & Hydraulic Pin Clevis, Direct Hydraulic Pin Cotter, Engine & Hydraulic Pin Cotter, Direct Hydraulic Gearcase Conveyor, Engine Drive Gearcase Conveyor, Hydraulic Drive Plug Pull Sprocket Key - Square Screw Set Base Engine Wldmt Base Hydraulic Wldmt Support Engine Base Support Hydraulic Base Belt Wiper Cap Screw 1/4 x X1 Washer Flat 1/4 SS Nut Hex 1/ Bearing Flange Cap Screw 5/16 x 1 1/ Washer Flat 5/ Washer Lock 5/ Nut Hex 5/ Cap Screw 1/2 x Washer Lock 1/ Bolt Carriage 3/8 x 1 1/ Washer Lock 3/8 AR Nut Hex 3/8 AR Cap Screw 3/8 x Washer Flat 3/ Bolt Carriage 3/8 x 1 AR Support Wldmt Hood Hook 1 9

10 CONVEYOR HEADERIDLER CS SS Shaft - Idler Assy, Includes Items Shaft Idler Sprocket Idler Bearing Screw 5/8 Take-up Nut Hex 5/8 2 10

11 #1 CONVEYOR HEADERCHAIN Chain Conveyor Assy, 7 Unit Chain Conveyor Assy, 8 Unit Chain Conveyor Assy, 9 Unit X2 Chain Conveyor Assy, 10 Unit Bar Cross Wldmt AR Link Chain AR Pin Chain AR Pin Cotter AR AR - As Required 11

12 FEEDGATE HEADER Bolt Carriage 3/8 x Washer Flat 3/ Nut Lock 3/ Feedgate Wldmt Lever Wldmt Washer Flat 1/ Nut Lock 1/ Link 1 12

13 NOTES This page is intentionally left blank. 13 NOTES

14 SPINNER HEADER SPINNER HOPPER Note: Standard height, engine/single hydraulic drive. 14

15 SPINNER HOPPER HEADERCONTINUED CS SS Spinner Assy, Engine & Single Hydraulic Drive X X2 Spinner Assy, Dual Hydraulic Drive Spinner Assy 12 Ext., Engine & Single Hydraulic Drive * Hardware Kit Spinner Mount, Includes Chain Roller Link Connecting Sprocket Engine & Single Hydraulic 1 *11431-X X1 Coupling Dual Hydraulic Screw Set 1/4-20 x 1/ Key Square 3/16 x 1-1/ Shaft Spinner Shaft Spinner 12 Ext Bearing Zerk Grease Extended Bolt Carriage 3/8 x 1-1/ Hopper Wldmt Hopper Wldmt 12 Ext Rod Rear Adjustment Pin Cotter Pin Hair Washer Flat 3/ Washer Lock 3/ Nut Hex 3/ Baffle Rear Wldmt Rod Side Adjustment Pin Clevis 5/16 x 2-1/ Baffle Side Wldmt Pin Cotter Disc Spinner Wldmt Pin Clevis 1/4 x 1-1/ Baffle Inner RH Baffle Inner LH 1 25 * Cap Screw 3/8 x * Washer Flat 3/ * Washer Lock 3/ * Nut Hex 3/8 4 * - Not Shown 15

16 SPINNER HOPPER HEADER- EXTENDED 16

17 SPINNER HOPPER HEADER - EXTENDED CONTINUED CS SS Hopper 12 Ext. Spinner Assy, Engine Drive X X3 Hopper 12 Ext. Spinner Assy, Hydraulic Drive Hopper 24 Ext. Spinner Assy, Engine Drive Hopper 24 Ext. Spinner Assy, Hydraulic Drive Chain Roller, Engine Drive only Sprocket Engine Drive 1 * X X1 Coupling Motor, Hydraulic Drive Screw Set 1/4 x 1/ Key Square 3/16 x 1-1/2, Engine Drive Key Square 3/16 x 1, Hydraulic Drive Shaft Spinner 12 Ext Shaft Spinner 24 Ext Bearing Zerk Grease Extended Bolt Carriage 3/8 x 1-1/ Hopper Spinner Wldmt 12 Ext Hopper Spinner Wldmt 24 Ext Rod Rear Adjustment Pin Cotter Pin Hair Washer Flat 3/ Washer Lock 3/ Nut Hex 3/ Baffle Rear Wldmt Rod Side Adjustment Pin Clevis 5/16 x 2-1/ Baffle Side Wldmt Pin Cotter Disc Spinner Wldmt Pin Clevis 1/4 x 1-1/ Baffle Inner RH Baffle Inner LH 1 25 * Cap Screw - 3/8 x * Nut - Hex 3/ * Washer - Lock 3/ * Washer - Flat 3/8 6 * - Not Shown Items used to mount hopper 17

18 SPINNER HOPPER HEADER- FLIP-UP 18,19,20, , ,23 15,16, , REAR VIEW 9 Note: Standard height, engine/single hydraulic drive spinner shown. CS SS Spinner Assy Flip-Up, Eng. & Single Hyd. Drive * Spinner Assy Flip-Up, Dual Hydraulic Drive * Spinner Assy Flip-Up 12 Ext., Engine & Single Hydraulic Drive * Hardware Kit Spinner, Includes 24 (1) &

19 SPINNER HOPPER HEADER - FLIP-UP CONTINUED Shaft Wldmt Flip-Up Bearing Pillow Block Key Square 3/16 x 1-1/ Screw Set 1/4-20 x 1/ Sprocket 24T, Engine & Single Hyd. 1 * X X1 Coupling Motor, Dual Hydraulic Panel Wldmt Wrap Hopper Wldmt Flip-Up 1 * Hopper Wldmt Flip-Up, 12 Ext Baffle Wldmt Rear Baffle Wldmt Side Rod Control Side Rod Control Rear Baffle Wldmt Inner LH 1 13 * Baffle Wldmt Inner RH Shaft Wldmt Spinner 1 * Shaft Wldmt Spinner, 12 Ext Disc 11-3/4 Wldmt Pin Clevis 1/4 x 1-1/ Pin Cotter 3/32 x 3/ Bolt Carriage 3/8 x 1-1/ Washer Flat 3/ Washer Lock 3/ Nut Hex 3/ Pin Clevis 5/16 x 2-1/ Pin Cotter 3/32 x 1/ Pin Hair 1-7/16 x Rod Spinner Flip-Up Rod Hanger Flip-up 1 27 * Cap Screw 3/8 x * Washer Flat 3/ * Washer Lock 3/ * Nut Hex 3/8 6 * - Not Shown 19

20 ENGINE DRIVE HEADER ELECTRIC CLUTCH 1 10,11,12 17,18 6,7 4 19,20 2 3,5 9,12,13,14 8,12, ,12, ,18 Note: Honda engine shown. 20

21 ELECTRIC CLUTCH HEADERCONTINUED CS SS Engine Assy 11 HP Honda Engine Assy 10.5 HP B&S Collar Set Clutch Electric Sprocket 52T Chain Roller Key 1/4 x 3/16 x 1-1/ Cap Screw 5/16 x 5/ Washer Lock 5/ Cap Screw 3/8-16 x 2-3/ Bolt Carriage 3/8-16 x Cap Screw 3/8-16 x 1-3/ Washer Flat 3/ Washer Lock 3/ Nut Hex 3/ Guard Plate Engine Grommet Rubber Grommet Rubber Base Wire Tie Tie Wire Clamp Rubber Coated Screw Self Tapping 2 21 * Cable Battery Ground 1 22 * Wire Assy, Honda only 1 23 * Cable Assy, B&S only 1 24 * Cable Battery Honda Engine 1 * Cable Battery B&S Engine Harness Assy Honda Engine, See Control Panel parts list * - Not Shown Harness Assy B&S Engine, See Control Panel parts list

22 ENGINE HEADER - 11 HP HONDA 22

23 ENGINE - 11 HP HEADER HONDA CONTINUED CS SS Engine Assy Honda 11 HP Engine Honda 11 HP Throttle Assy 11 HP, Includes 17-21, Base Wldmt Engine Sprocket Key Square 1/4 x 1-1/ Screw Set 1/4 x 1/ Cap Screw 5/16-18 x 1-1/ Cap Screw 5/16-24 x 3/ Washer Lock 5/ Nut Hex Lock 5/ Grommet Rubber Spring Choke Exhaust Wldmt Honda Cap Screw 3/8 x 1-1/ Washer Lock 3/ Nut Hex 3/ Control Electric Throttle Linkage Throttle Retainer Push Screw Machine #8-32 x 5/ Nut Lock # Screw Pan Head M5 x Bracket Throttle Switch Snap Action Screw Machine #8-32 x 3/ Screw 1/4-20 x 3/8 Hex Head Washer Lock 1/ Plate Wldmt Switch Screw Machine #4-40 x 5/ Nut Lock # Terminal - Ring Connector - Butt Splice Connector - Wire Male 1 23

24 ENGINE HP HEADER BRIGGS & STRATTON 24

25 ENGINE HP BRIGGS HEADER & STRATTON CONTINUED CS SS Engine Assy Briggs & Stratton 10.5 HP Base Wldmt Engine Grommet Rubber Throttle Assy 10.5 HP, Includes Switch Solenoid Magnetic Cap Screw 1/4 x 5/ Washer Flat 1/ Washer Lock 1/ Nut Hex 1/ Engine B&S 10.5 HP Exhaust Wldmt B & S Sprocket Key Square 1/4 x 1-1/ Screw Set 1/4 x 1/ Cap Screw 5/16 x 1-1/ Washer Flat 5/ Washer Lock 5/ Nut Hex 5/ Cap Screw 3/8 x 1-1/ Washer Lock 3/ Nut Hex 3/ Block Throttle Bracket Wldmt Throttle Control Electric Throttle Screw Machine #8-32 x 5/ Nut Lock # Plate Wldmt Switch Switch Snap Action Screw Machine - #8-32 x 3/ Screw 1/4-20 x 3/ Washer Lock 1/ Screw Machine #4-40 x 5/ Nut Lock # Connector - Butt Splice Connector - Wire Male Terminal - Ring 1 25

26 ENGINE HEADER HOOD CS SS Hood Wldmt Pivot Wldmt Bracket Anchor Bracket Hood Hook Rubber Cap Screw - #10 x 1/ Washer Lock # Nut Hex # Cap Screw 1/4 x 1-1/ Nut Lock 1/ Cap Screw 5/16 x 3/ Washer Lock 5/ Nut Hex 5/ Bolt Carriage 5/16 x 3/ Nut Lock 5/ Decal - Warning Moving Part Hazard 1 17 * Decal Danger Guard Missing (Engine Base) 1 18 * Seal - Rubber AR * - Not Shown AR - As Required 26

27 HEADER GUARDS 2,3,4,5 1 CS SS X X1 Guard Wldmt Engine Guard Wldmt Hydraulic Cap Screw 1/4 x 3/ Washer Flat 1/ Washer Lock 1/ Nut Hex 1/4 3 6 * Chain Roller 41-1/2 1 * - Not Shown 27

28 CONTROL PANEL HEADER & CONNECTIONS 9 11, =YELLOW (WITH INSERT) 13,14,15 5=RED =GREEN 1=WHITE 4=BLACK 2=BLUE 6=BROWN 5=RED 7=YELLOW (WITH INSERT) 23 1=WHITE 3=GREEN 2=BLUE 4=BLACK 6=BROWN 28

29 CONTROL PANEL & HEADER CONNECTIONS CONTINUED Control Panel Rear with Choke Light, Includes 1-19 * Control Panel Kit Plug Mounting, Includes * Loom Assy 12 Extension w/ Choke Lt Switch Rocker Double Pole Switch Rocker Double Pole Switch Rocker Panel Front Cover Wldmt Panel Decal Control Panel Bracket Mount Knob Assy Bushing Bushing Holder Fuse Fuse 10 Amp Screw Round Head Washer Star Nut Hex # Screw Self Tapping Cable Assy Control Panel 1 18 * Harness Assy 1 19 * Cable Assy 1 20 * Bracket Mounting 1 21 * Screw Round Head 4 22 * Nut Hex # Harness Assy Honda Engine Harness Assy B&S Engine 1 * - Not Shown 29

30 NOTES This page is intentionally left blank. NOTES 30

31 HYDRAULIC DRIVE HEADER DIRECT DRIVE 2 3,4 1 5,7,8,9 10 6,8 CS SS Mount Wldmt Motor Motor Hydraulic Seal Kit Motor Service Kit Motor Cap Screw 1/2 x 1-1/ Nut Hex 1/ Bolt Carriage 3/8 x Cap Screw 3/8 x 3/ Washer Flat 3/ Washer Lock 3/ Nut Hex 3/ Motor Hydraulic Seal Kit Motor 1 31

32 SINGLE HYDRAULIC HEADER DRIVE 16,17,18, ,3,4,5 11,12 8,9, ,

33 SINGLE HYDRAULIC HEADER DRIVE CONTINUED CS SS Bearing 2-Bolt Cap Screw 5/16 x 1-1/ Washer Flat 5/ Washer Lock 5/ Nut Hex 5/ Mount Wldmt Motor Motor Hydraulic Seal Kit Motor Coupling Motor Key Square 1/4 x 1-1/ Screw Set 1/4-20 x 1/ Cap Screw 1/2 x 1-1/ Nut Hex 1/ Guard Panel Cap Screw 1/4 x 3/ Washer Lock 1/ Bolt Carriage 3/8 x Washer Flat 3/ Washer Lock 3/ Nut Hex 3/ Guard Plate Hydraulic 1 33

34 DUAL HYDRAULIC HEADER DRIVE 17 11,12 7 8,9,10 2,3,4, ,19,20, ,

35 DUAL HYDRAULIC HEADER DRIVE CONTINUED CS SS Bearing 2-Bolt Cap Screw 5/16 x 1-1/ Washer Flat 5/ Washer Lock 5/ Nut Hex 5/ Mount Wldmt Motor Motor Hydraulic Seal Kit Motor Coupling Motor Key Square 1/4 x 1-1/ Screw Set 1/4-20 x 1/ Cap Screw 1/2 x 1-1/ Nut Hex 1/ Guard Panel Cap Screw 1/4 x 3/ Washer Lock 1/ Mount - Wldmt Motor Motor - Hydraulic Seal - Kit Motor Bolt Carriage 3/8 x Washer Flat 3/ Washer Lock 3/ Nut Hex 3/8 4 35

36 HYDRAULICS HEADER - SINGLE 36

37 HYDRAULICS HEADER - SINGLE CONTINUED Tank Hydraulic Assy 1 * Cap Filler Assy 1 * 6033 Plug Pipe Filter Hydraulic Nipple Close Tee Disconnect Quick Male Disconnect Quick Female Nipple Hose Hose Return Clamp Hose Nipple Hose Adapter Nipple Hose End Hose Reusable Hose End Hose Reusable Disconnect Quick Male Disconnect Quick Female Adapter Valve Control Bracket Valve Mounting Cap Screw - 1/4 x Washer Lock 1/ Nut Hex 1/ Adapter Adapter Hose Suction Valve Gate Nipple Nipple Hose Adapter Clamp - Hose 2 * - Not shown 37

38 HYDRAULICS HEADER- DUAL ,32, End Hose End Hose Disconnect Quick Male Disconnect Quick Female End Hose Adapter Elbow Tee Swivel Nut Valve Control Fitting Hose Reusable Adapter Connector 2 38

39 HYDRAULICS HEADER - DUAL CONTINUED Adapter Connector Hose Assy End Hose Fitting Hose Reusable Fitting Hose Reusable Disconnect Quick Male Disconnect Quick Female Hose AR * 6335 Clamp Hose AR Hose AR Hose Cut to Length AR Hose AR * Clamp Hose AR Filter Oil Filter Indicator Service Tank Hydraulic 1 * Cap Filler 1 * 6033 Plug Pipe Valve Gate Nipple Pipe Tee Pipe Nipple Pipe Adapter Elbow Adapter Connector Adapter Connector 1 31 Motor Hydraulic, See Dual Hydraulic Drive Nipple Pipe Coupling 1 * - Not Shown AR - As Required 39

40 PEDESTAL HEADER MOUNT KIT T - TANK P - PUMP PRESSURE S - SPINNER A - AUGER/CONVEYOR Cap Screw 1/4 x Adapter Adapter Mount Valve Wldmt Tube Hydraulic Adapter Bushing Adapter 1 40

41 HEADER LIGHTS 1 * Kit Warning Light Red 1 2 * Light Warning Amber 1 * - Not Shown NOTE: Install lights and reflective devices to conform to FMVSS-108 and state requirements. 41

42 DECALS *Items 9 & 10 for engine driven units only 9 42

43 DECALS HEADER CONTINUED Decal - Model P Decal - Hi-Way Small Black Decal - Caution Operation & Maint Decal - Danger Moving Part Hazard Decal - Caution Hazardous Material Decal - Warning Moving Part Hazard Decal - Danger Flying Material Decal - Warning Falling Hazard Decal - Danger Explosion Hazard Decal - Danger Guard is Missing Decal Notice Keep Valve Open Decal Notice Hydraulic Oil Only Decal Oil Filter 1 14 *79692 Decal - Warning, See Engine Hood Parts Page for Details 1 * - Not Shown 43

44 MOUNTING KIT Strap Ratchet 4 44