TEST REPORT No a
|
|
- Nelson Houston
- 6 years ago
- Views:
Transcription
1 AGRICULTURAL MACHINES FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT No a TANK FOR AGRICULTURAL SPRAYERS: SERIE LINEA 800 (extension: b SERIE LINEA 1000) MANUFACTURER: VERZELLESI S.R.L. Via Zuccardi, 20/ Campagnola Emilia (REGGIO EMILIA) - ITALY Rome, November /8
2 TESTS CARRIED OUT IN COMPLIANCE WITH ENAMA SPECIFICATIONS NO. 47 REV. 01 BY THE MECHANICS SECTION OF THE DEPARTMENT OF AGRICULTURAL, FOREST AND ENVIRONMENTAL ECONOMICS AND ENGINEERING, UNIVERSITY OF TURIN: SUPERVISOR: DATA COLLECTORS: Prof. Paolo Balsari Dr Mario Tamagnone Dr Paolo Marucco TABLE OF CONTENTS TECHNICAL DATA 3 DESCRIPTION OF COMPONENT 4 TEST METHOD 4 RESULTS 4 NOTES ON RESULTS 7 To facilitate interpretation of the results, it should be remembered that: 1 MPa = 1000 kpa = 10 bar 10 kg force /cm 2 1 dan 1,02 kg force 1 kw = 1.36 CV 1 m 3 /s = 3600 m 3 /h 1 m/s = 3.6 km/h 1 l = 1 dm 3. 2/8
3 Technical data Size model nominal capacity (l) length (mm) width (mm) height (mm) Linea ,855 1,020 1,060 Linea ,000 1,985 1,160 1,040 Material: polyethylene 3/8
4 Description of component These tanks are designed for use with sprayers for the distribution of chemical products. They are made out of polyethylene, obtained via rotational moulding. There is a compartment in the front part of the tank to house the pump and tubing. On the side, to the rear, are the seats for the machine s wheels. All models are equipped with auxiliary tanks for cleaning the distribution circuit and for hand washing. The circuit cleaning tank is positioned in the front part, above the pump compartment. Liquid level inside the main tank is displayed in the front right part and on the left side via gauges etched directly in the polyethylene. Access to the main tank is via two openings positioned on the left side. The lower part of the main tank is shaped such a way as to facilitate emptying, even in an inclined position. Test method The functional parameters examined were the maximum capacity of the various tanks, the accuracy of level indicators of the main tank and the roughness of inside and outside surfaces. Values were calculated using water, free of suspended solids, and electronic scales. Results Capacity Main tank The maximum capacities measured close to the opening are given in the table below. Model max. capacity (l) difference vis-à-vis nominal value Linea % Linea , % All models had maximum capacities exceeding 5% of the nominal value, in keeping with the legal limit established for sprayers. 4/8
5 Circuit cleaning tank model max. capacity (l) % vis-à-vis nominal value Linea % Linea % For the Linea 1000 model the capacity of the circuit cleaning tank is 10% lower than the nominal capacity of the main tank, thus the extent of the dilutable volume after the tank is installed in the sprayer will have to be checked. Hand washing tank The capacity of the hand washing tank, the same for all models, is 15.7 l. This value was above the legal minimum of 15 l. Gauge Tanks having a nominal capacity of up to 1,000 l are fitted with gauges having a scale in intervals of 50 l, while those having a higher capacity are in intervals of 100 l. For some models lower scale markings are not shown on the tank because of the rounded shape of the lower part of the tank. For each of these the manufacturer provides the indications (vertically from the first marking etched in the polyethylene) needed to position them correctly on the frame of the finished machine. Up until 20% of nominal capacity, the maximum difference between the value indicated by the scale markings and the actual amount of liquid in the tank must be ±7.5% in accordance with reference legislation. For all the tanks to which the present test report refers, measured values were below the limit, as can be seen in the table below. model front indicator side indicator Linea % -5.7% Linea % 5.3% Over 20% of nominal capacity, the maximum allowed difference is ±5.0%. Measured values are given in the table below. model front indicator side indicator Linea % -4.2% Linea % 4.3% The graphs below show, for both tanks tested and for both content indicators (front and side), the differences (% error) between the value indicated by scale markings and the actual amount of liquid in the tank. 5/8
6 error 8% 6% 4% 2% 0% Linea 800 front side -2% -4% -6% -8% Indicated value(l) error 8% 6% 4% 2% 0% -2% -4% -6% -8% Linea 1000 front side Indicated value(l) 6/8
7 Roughness Surface roughness of tanks was below the limit of 100 µm established by reference legislation. Measured values are given in the table below. model external roughness (Rz - µm) internal roughness (Rz - µm) Linea Linea Notes on results The tanks examined, designed for use with trailed sprayers, successfully met regulatory requirements. For some parameters, the installer must observe the recommendations given by the tank manufacturer in order to guarantee the above results for the end product, i.e. the sprayer. 7/8
8 THE PRESENT TEST REPORT IS VALID UNTIL REFERENCE REGULATIONS CHANGE FOR THE TANK FOR AGRICULTURAL SPRAYERS MOD. SERIE LINEA 800, MANUFACTURER: VERZELLESI S.R.L. THE PRESENT TEST REPORT IS OFFICIALLY RECOGNISED BY THE FOLLOWING ENTAM MEMBERS WITH THEIR RELATIVE RECOGNITION NUMBERS: This Test Report is registered at ENTAM, the European Network of Testing Agricultural Machines. The aim of ENTAM is to promote and to spread Test Report of Agricultural and Forestal Machines for farmers, dealers, machine owners and manufacturers. For more informations please visit: or send an to: ENAMA ENTE NAZIONALE PER LA MECCANIZZAZIONE AGRICOLA (Italian Agricultural Mechanisation Body) VIA LAZZARO SPALLANZANI, 22/A ROME TEL. 06/ FAX 06/ info@enama.it 8/8
TEST REPORT No a
AGRICULTURAL MACHINES FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT No. 47 002a TANK FOR AGRICULTURAL SPRAYERS: SERIE LINEA TC 600 (extension: 47.002b Serie Linea TC 1000; 47.002c - Serie Linea TC
More informationTEST REPORT No a
AGRICULTURAL MACHINES FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT No. 47 002a TANK FOR AGRICULTURAL SPRAYERS: SERIE LINEA TC 600 (extension: 47.002b Serie Linea TC 1000; 47.002c - Serie Linea TC
More informationCERTIFICATE No a
AGRICULTURAL MACHINERY FUNCTIONAL AND SAFETY TESTING SERVICE CERTIFICATE No. 47 3a TANK FOR SPRAYERS: ELLISSE 3 SERIES (extensions: 47.3b Serie Ellisse 25; 47.3c - Serie Ellisse 2) MANUFACTURER: VERZELLESI
More informationTEST REPORT No a
AGRICULTURAL MACHINES FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT No. 05 109a AIR-ASSISTED SPRAYER: FRIULI POLY 1000/8 (extension: 05-109b FRIULI POLY 800/8) MANUFACTURER: AGRICOLMECCANICA S.N.C.
More informationENTAM - Test Report. Mounted Air Assisted Sprayer Unigreen s.p.a. P6 TGZ 650 P6 600TV - P6 700 TV. Sprayer type: Trade mark: Model: Extensions:
ENTAM - Test Report Sprayer : Trade mark: Model: Extensions: Mounted Air Assisted Sprayer Unigreen s.p.a. P6 TGZ 650 P6 600TV - P6 700 TV Manufacturer: Unigreen s.p.a. Via Rinaldi, 105 Reggio Emilia -
More informationENTAM TEST REPORT No a
AGRICULTURAL MACHINES FUNCTIONAL AND SAFETY TESTING SERVICE ENTAM TEST REPORT No. 05.102a AIR-ASSISTED FIELD SPRAYER: IBIS 25 - ALA UNI 21 (extensions: 05-102b IBIS 25 ALA UNI 18; 05-102c IBIS 25 ALA UNI
More informationTEST REPORT No a
AGRICULTURAL MACHINES FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT No. 05 117a FIELD CROP SPRAYER: COLIBRI 1500 DM PLUS SPECIAL 18 (extensions: see inside) MANUFACTURER: RIMECO ITALIA S.R.L. Via Carlo
More informationAGRICULTURAL MACHINES FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT
AGRICULTURAL MACHINES FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT No. 49-003 CUT-OUT CLUTCH: EK 62/2S MANUFACTURER: GKN Walterscheid GmbH HAUPTSTRASSE 150 53797 LOHMAR (GERMANY) Rome, November 2003
More informationTEST REPORT No
TESTING SERVICE OF FUNCTIONAL AND SAFETY CHARACTERISTICS OF AGRICULTURAL MACHINES TEST REPORT No. 49 001 AUTOMATIC LIMITER WITH VOLUNTARY DISENGAGEMENT: H-TLD MANUFACTURER: COMER GROUP S.P.A. Via Magellano
More informationTEST REPORT No
TESTING SERVICE OF FUNCTIONAL AND SAFETY CHARACTERISTICS OF AGRICULTURAL MACHINES TEST REPORT No. 49 002 AUTOMATIC LIMITER WITH VOLUNTARY DISENGAGEMENT: M-TLD MANUFACTURER: COMER GROUP S.P.A. Via Magellano
More informationTEST REPORT n 40b - 001
TESTING SERVICE OF FUNCTIONAL AND SAFETY CHARACTERISTICS OF AGRICULTURAL MACHINES TEST REPORT n 40b - 00 CBM GROUP COUPLING, TOWING AND LIFTING SYSTEM MANUFACTURER: CBM S.P.A. COSTRUZIONI MECCANICHE Via
More informationENTAM - Test Report. Sprayer type: Trade mark: Model: Trailed air assisted sprayer Lochmann RPS 15/90 Q. Test report: D
ENTAM - Test Report Sprayer type: Trade mark: Model: Trailed air assisted sprayer Lochmann RPS 15/90 Q Manufacturer: Lochmann Plantatec GmbH-Srl Vilpianer Straße 42 39010 Nals (BZ) ITALY July 2015 2 Assessment
More informationTEST REPORT No a
AGRICULTURAL MACHINERY FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT No. 03 052a SUBSOILER: Artiglio 300 (extensions: 03.052b - Artiglio 250, 03.052c - Artiglio 400) MANUFACTURER: GASPARDO SEMINATRICI
More informationENTAM - Test Report. Trailed field crop sprayer Agrifac Milan 4200 Basis. Sprayer type: Trade mark: Model: Test report: D
ENTAM - Test Report Sprayer type: Trade mark: Model: Trailed field crop sprayer Agrifac Milan 4200 Basis Manufacturer: Agrifac Machinery B.V. Eesveenseweg 15 NL-8332 JA Steenwijk August 2018 2 Assessment
More informationENTAM - Test Report. Sprayer type: Trade mark: Model: Built on field crop sprayer John Deere R4050i WS. Test report: D
ENTAM - Test Report Sprayer type: Trade mark: Model: Built on field crop sprayer John Deere R4050i WS Manufacturer: John Deere Fabriek Horst B.V. Energiestraat 16 NL 5961 HORST Netherlands March 2017 2
More informationFARMGÉP KFT. End of testing: November 2010 H-4031 DEBRECEN Szoboszlói út 50.
Sprayer type: Self Propelled Field Crop Sprayer Trade mark: KERTITOX Model: 3000/24 Manufacturer: Test report: H_ENTAM_4_2010 FARMGÉP KFT. End of testing: November 2010 H-4031 DEBRECEN Szoboszlói út 50.
More informationENTAM - Test Report. Sprayer type: Trade mark: Model: Trailed air assisted sprayer Munckhof 105. Test report: D
ENTAM - Test Report Sprayer type: Trade mark: Model: Trailed air assisted sprayer Munckhof 105 Manufacturer: Machinefabriek J.M. van den Munckhof B.V. Venrayseweg 126c 5961-AJ Horst The Netherlands April
More informationENTAM - Test Report. Sprayer type: Trade mark: Model: Trailed field crop sprayer Leeb GS 8000 / 36m. Test report: D
ENTAM - Test Report Sprayer type: Trade mark: Model: Trailed field crop sprayer Leeb GS 8000 / 36m Manufacturer: Horsch Maschinen GmbH Sitzenhof 1 92421 Schwandorf Germany June 2013 2 Assessment table
More informationENTAM - Test Report. Sprayer type: Trade mark: Model: Built on field crop sprayer DAMMANN DTP 6036 on carrier vehicle DAMMANN-TRAC DT 2500 S4
ENTAM - Test Report Sprayer type: Trade mark: Model: Built on field crop sprayer DAMMANN DTP 6036 on carrier vehicle DAMMANN-TRAC DT 2500 S4 Manufacturer: HERBERT DAMMANN GmbH Dorfstrasse 17 21614 Buxtehude-Hedendorf
More informationTEST REPORT No
AGRICULTURAL MACHINERY FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT No. 02-013 HORIZONTAL FLAIL MOWER: TSMA 180 MANUFACTURER: GF COSTRUZIONI MACCHINE AGRICOLE S.R.L. Via Cassia Cimina Km 29.200 Loc.
More informationTEST REPORT No a
AGRICULTURAL MACHINERY FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT No. 03 039a REVERSIBLE PLOUGH: Vari Legender 180 OL 3E (extensions: 03.039b - Vari Legender 180 OL 2E; 03.039c - Vari Legender 180
More informationFARMGÉP KFT. End of testing: June H-4031 DEBRECEN Szoboszlói út 50.
Sprayer type: Trailed Air Assisted Sprayer Trade mark: KERTITOX Model: Bóra 2000 32 DT Manufacturer: Test report: H_ENTAM_1_2010 FARMGÉP KFT. End of testing: June 2010. H-4031 DEBRECEN Szoboszlói út 50.
More informationTEST REPORT No. 14a 003a
AGRICULTURAL MACHINES FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT No. 14a 003a ROTARY MOWER CONDITIONER: FC 243 RTG (extension: 14a-003b - FC 283 RTG) MANUFACTURER: KUHN S.A. 67706 SAVERNE CEDEX
More informationFORRÁS GÉPEK KFT. End of testing: January 2012 H-6793 FORRÁSKÚT Felszabadulás u. 13.
Sprayer type: Mounted Air-Assisted Sprayer Trade mark: FORRÁS Model: 300 AXI Manufacturer: Test report: H_ENTAM_5_2011 FORRÁS GÉPEK KFT. End of testing: January 2012 H-6793 FORRÁSKÚT Felszabadulás u. 13.
More informationENTAM - Test Report. Sprayer type: Trade mark: Model: Built on field crop sprayer John Deere 5430 on carrier vehicle 5430i. Test report: D
ENTAM - Test Report Sprayer type: Trade mark: Model: Built on field crop sprayer John Deere 5430 on carrier vehicle 5430i Manufacturer: John Deere Fabriek Horst BV Energiestraat 16 5961 PT Horst Netherlands
More informationENTAM - Test Report. Sprayer type: Trade mark: Model: Trailed field crop sprayer Dammann ANP Test report: D
ENTAM - Test Report Sprayer type: Trade mark: Model: Trailed field crop sprayer Dammann ANP 6030 Manufacturer: Herbert Dammann GmbH Dorfstraße 17 21614 Buxtehude-Hedendorf Germany March 2013 2 Assessment
More informationTEST REPORT n a
TESTING SERVICE OF FUNCTIONAL AND SAFETY CHARACTERISTICS OF AGRICULTURAL MACHINES TEST REPORT n. 03-035a ROTARY HARROW: ERS 302.16/20 (extensions : 03-035b ERS 402.16/20) MANUFACTURER: FRANDENT DI BRUNO
More informationENTAM - Test Report. Trailed Field Crop Sprayer John Deere 740. Sprayer type: Trade mark: Model: Test report: D
ENTAM - Test Report Sprayer type: Trade mark: Model: Trailed Field Crop Sprayer John Deere 740 Manufacturer: John Deere Fabriek Horst B.V. Energiestraat 16 NL - 5961 PT HORST Test report: D - 1759 May
More informationTEST REPORT No a
AGRICULTURAL MACHINES FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT No. 08 010a SELF-PROPELLED MOWER: TURBO 1 (extensions: 08-010b Turbo 2; 08-010c Turbo 4) MANUFACTURER: GIANNI FERRARI S.R.L. Via
More informationENTAM - TEST REPORT Trailed Field Crop Sprayer John Deere 840 Design
European Network for Testing Agricultural Machinery ENTAM - TEST REPORT Trailed Field Crop Sprayer John Deere 840 Design 840-27-002 Manufacturer: Test report: D - 1671 John Deere Fabriek Horst B.V. Energiestraat
More informationSolomix VLH-B Feed-Mixer Wagon
Trioliet Mullos B.V. Solomix 2-2000 VLH-B Feed-Mixer Wagon Mixing, weighing, power consumption DLG Test Report 615 F Brief description Applicant/manufacturer Trioliet Mullos B.V. Hinmanweg 19 NL-7575 BE
More informationTESTING SERVICE OF FUNCTIONAL AND SAFETY CHARACTERISTICS OF AGRICULTURAL MACHINES
TESTING SERVICE OF FUNCTIONAL AND SAFETY CHARACTERISTICS OF AGRICULTURAL MACHINES TEST REPORT n. 03-034a ROTARY TILLER: EL 102/230 (extensions : 03-034b EL 102/250; 03-034c EL 102/300) MANUFACTURER: KUHN
More informationRear-mounted disc mower DISCO 3500 Contour
Claas Saulgau GmbH Rear-mounted disc mower DISCO 3500 Contour Power and quality of work DLG Test Report 5950 F Brief description Manufacturer and applicant Claas Saulgau GmbH Zeppelinstrasse 2 D-8838 Bad-Saulgau
More informationECONOMISER SERIES E2T USER MANUAL
TURBO S.R.L. Electronic Control Systems for Dust Collectors e-mail: info@turbocontrols.it web: www.turbocontrols.it TEL. ++39 (0)362 574024 FAX ++39 (0)362 574092 ECONOMISER SERIES E2T USER MANUAL 24/06/2014
More informationTECHNICAL CATALOGUE FD/FDM FDM
l. ORS TECHNICAL FLOW DIVIDERS DATA FD/FDM MODEL SERIES TECHNICAL CATALOGUE FD FD bar FDM bar FDM INDEX GENERAL INFORMATION rpm - - - 950 - - - - - 950 - - - - - 950 - - - - - 0 - - - - - 0 - - - - - 750
More informationGrammer seat MSG 95 EAC/741 with active seat suspension
GRAMMER AG Seating Systems Grammer seat MSG 95 EAC/741 with active seat suspension ride comfort DLG Test Report 5542F Evaluation short version 11/05 ride comfort Manufacturer and registering company GRAMMER
More informationTEST REPORT No. 05d - 001
AGRICULTURAL MACHINERY FUNCTIONAL AND SAFETY TESTING SERVICE TEST REPORT No. 05d - 001 MACHINE FOR SOIL DISINFECTION AND DISINFESTATION USING STEAM AND EXOTHERMIC REACTION SUBSTANCES (BIOFLASH SYSTEM):
More informationABSOLUTE QUALITY EXCELLENCE ON A HUMAN SCALE
ABSOLUTE QUALITY EXCELLENCE ON A HUMAN SCALE The characteristics of Dieci products can be summarized in three concepts that have always been the hallmark of each vehicle: technology, reliability and durability.
More informationCEMA position on draft braking regulation, 4 June 2008 ENTR/F1/ /rev16
CEMA PT16 N05Rev CEMA position on draft braking regulation, 4 June 2008 ENTR/F1/5030-99/rev16 CEMA is the European association representing the agricultural machinery industry. It represents the industry
More informationCLAAS Selbstfahrende Erntemaschinen GmbH "DYNAMIC POWER" DLG Test Report 6027 F Brief description Manufacturer
CLAAS Selbstfahrende Erntemaschinen GmbH "DYNAMIC POWER" Operation in grass with a CLAAS Jaguar 960 Tier 4i DLG Test Report 6027 F Brief description Manufacturer CLAAS Selbstfahrende Erntemaschinen GmbH
More informationBy your side, always!
Images are for illustration purposes only and may have different optional accessories and versions. Check available settings at a dealer near you. This leaflet does not void the need to read the operator's
More informationEXPLANATORY NOTE LIQUIFIED PETROLEUM GASES TRANSPORTED IN STATIONARY TANKS PERMANENTLY MOUNTED ON TRAILERS
EXPLANATORY NOTE LIQUIFIED PETROLEUM GASES TRANSPORTED IN STATIONARY TANKS PERMANENTLY MOUNTED ON TRAILERS 1. ISSUE Liquefied petroleum gases (LPG) being transported in stationary tanks permanently mounted
More informationDIRECT CURRENT MOTORS
DIRECT CURRENT MOTORS Technical Catalogue November 2 web edition Index DC motors Description Type Page Introducion 2 V DC -.35 kw - D. 2521 V DC -. kw - D. 252 6 V DC - kw - D. 252 V DC - kw - D. 253
More informationEconomic and Social Council
United Nations Economic and Social Council ECE/TRANS/WP.29/2017/50 Distr.: General 23 December 2016 Original: English Economic Commission for Europe Inland Transport Committee World Forum for Harmonization
More informationMW HYDRAULIC POWER UNIT
MW HYDRAULIC POWER UNIT Technical Catalogue January 2018 web edition 2018 Dana Brevini S.p.A. All rights reserved. Hydr-App, SAM Hydraulik, Aron, Brevini Hydraulics, BPE Electronics, VPS Brevini, OT Oiltechnology,
More informationABSOLUTE QUALITY EXCELLENCE ON A HUMAN SCALE
ABSOLUTE QUALITY EXCELLENCE ON A HUMAN SCALE The characteristics of Dieci products can be summarized in three concepts that have always been the hallmark of each vehicle: technology, reliability and durability.
More informationInstruction of connection and programming of the VECTOR controller
Instruction of connection and programming of the VECTOR controller 1. Connection of wiring 1.1.VECTOR Connection diagram Fig. 1 VECTOR Diagram of connection to the vehicle wiring. 1.2.Connection of wiring
More informationA short Company & Technology Overview
A short Company & Technology Overview The Future of Rotary Wings Workshop Centro Alti Studi della Difesa (CASD) Rome, November 22 nd, 2012 An introduction to K4A K4A was founded in 2005 by Engineers and
More information-SQA- SCOTTISH QUALIFICATIONS AUTHORITY NATIONAL CERTIFICATE MODULE: UNIT SPECIFICATION GENERAL INFORMATION. -Module Number Session
-SQA- SCOTTISH QUALIFICATIONS AUTHORITY NATIONAL CERTIFICATE MODULE: UNIT SPECIFICATION GENERAL INFORMATION -Module Number- 2210034 -Session-1994-95 -Superclass- -Title- ZJ MOTOR VEHICLE INSPECTION: TACHOGRAPHS
More informationTester for Motor-Driven Relays Type Siemens SICO 1225 M A N U A L
Tester for Motor-Driven Relays Type Siemens SICO 1225 M A N U A L 8 Technical Data Operating temperature range 5 C 40 C Power supply 230 V, 50 Hz net Power input 25 W Protection degree IP 42 Protection
More informationHydraulic Pump Series F1 Fixed Displacement
Fixed Displacement Catalog 9129 8201-02 August, 1997 GB Content General information 3 Specifications 4 Pump and line selection 5 Ordering code 5 Standard versions 5 Installation dimensions 6 Installation
More informationSlide Measuring Instrument GMG 200
GTE Industrieelektronik GmbH Slide Measuring Instrument GMG 200 entsprechend DIN 51131 und EN 13893 GTE Ind.Elektronik Helmholtz Str. 38-40 D-41747 VIERSEN Tel.: ++49 - (0)2162 3703-0 Fax.:++49 - (0)2162
More informationHF C dc power packs for the use with external valves
HF C200 series Hydraulfunktion has more than 20 year successfully manufactured and constantly improved box type dc power packs. Based on our experience we have developed C200 series as new product line.
More informationCommercial Vehicle Drivers Hours of Service. Module 11. Special Permit Commercial Vehicles Other than Oil Well Service Vehicles. Microsoft.
Module 11 Special Permit Commercial Vehicles Other than Oil Well Service Vehicles Microsoft. June 23, 2008 Microsoft. Things to think about In some situations, a driver may not be able to reach a destination,
More informationHYDRONIC LIFT SOLUTION FOR A3 AMENDMENT
Page 1/38 Safety Valve HSV Installation, maintenance and startup guide HYDRONIC LIFT SOLUTION FOR A3 AMENDMENT Page 2/38 2011 by Hydronic Lift Spa All right reserved. This documentation, in whole and/or
More informationTEST REPORT HUSQVARNA 575 XPG
TEST REPORT HUSQVARNA 575 XPG TEST CERTIFICATE HOLDER: Manufacturer and applicant: Husqvarna AB SE- 561 82 Huskvarna www.husqvarna.de Test Results and Evaluations Chainsaw Husqvarna 575 XPG with 46 cm
More informationRequirements on vehicle occupant protection, including interior fittings, head restraints, seat belts, vehicle doors
L 42/70 EN Official Journal of the European Union 17.2.2015 ANNEX XIII Requirements on vehicle occupant protection, including interior fittings, head restraints, seat belts, vehicle doors 1. Definitions
More informationAIR BREATHER SERIES OTHER FILTER TYPES DESCRIPTION
ESCRIPTION MM Air breathers are ready and easy to use filters than can be used in any applications where tank fluid often rises and falls. Air Breathers ensure system cleanliness as they filter the air
More informationInstruction of connection and programming of the OSCAR-N controller
Instruction of connection and programming of the OSCAR-N controller Table of content Paragraph Description Page 1 Installation of OSCAR-N sequential gas injection system 2 1.1 OSCAR-N sequential gas injection
More informationTesting of particulate emissions from positive ignition vehicles with direct fuel injection system. Technical Report
Testing of particulate emissions from positive ignition vehicles with direct fuel injection system -09-26 by Felix Köhler Institut für Fahrzeugtechnik und Mobilität Antrieb/Emissionen PKW/Kraftrad On behalf
More informationTEST REPORT Chain saw DOLMAR PS-420
TEST REPORT Chain saw DOLMAR PS-420 OWNER OF THE TEST CERTIFICATE: Manufacturer and applicant: Dolmar GmbH Jenfelder Strasse 38 D-22045 Hamburg www.dolmar.com Prüfbericht PS 420 Chain saw DOLMAR PS 420
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-19459-8 SOUTH AFRICAN NATIONAL STANDARD Verification standards for the verification of volume-measuring instruments, including commercial standards of volume Published by Standards South
More informationHIGHWAY TRAFFIC ACT DRIVER S LICENSES REGULATIONS
c t HIGHWAY TRAFFIC ACT DRIVER S LICENSES REGULATIONS PLEASE NOTE This document, prepared by the Legislative Counsel Office, is an office consolidation of this regulation, current to May 6, 2017. It is
More informationNEW HOLLAND TL TL8O TL9O TL1OO
NEW HOLLAND TL TL8O TL9O TL1OO PIONEER POWERFUL, INNOVATIVE, OPERATOR FRIENDLY, ECONOMICAL, EFFICIENT, ROBUST rpm 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 100 Power 90 80 70
More informationTHE NEW MAN TGE. Technical data. Valid from October 1st 2017.
THE NEW MAN TGE. Technical data. Valid from October 1st 2017. DRIVELINE. 2.0 l 75 kw 2.0 l 90 kw 2.0 l 103 kw 2.0 l 130 kw Displacement [cm³] 1,968 1,968 1,968 1,968 Number of cylinders 4 4 4 4 max. power
More informationMod: KLD6-12/35XLAS-N
12/2011 Mod: KLD6-12/35XLAS-N Production code: 1914070 INSTRUCTION MANUAL LOGIC LINE PLUS HOOD Reseller Stamp for Warranty Dear customer, Above all, thank you for choosing our product and we would like
More informationPOWER SUPPLY UNIT FOR 3 KW MAGNETRON TECHNICAL NOTE
POWER SUPPLY UNIT FOR 3 KW MAGNETRON TECHNICAL NOTE (Issue April 2004) CE Declaration of Conformity Dichiarazione di Conformità CE Manufacturer s Name: Nome del Costruttore: Manufacturer s Address: Indirizzo
More informationANNEX MOTOR VEHICLES AND MOTOR VEHICLES' PARTS. Article 1. General Provisions
ANNEX MOTOR VEHICLES AND MOTOR VEHICLES' PARTS Article 1 General Provisions 1. This Annex shall apply to motor vehicles in UNECE vehicle regulations' category M1 as well as parts and equipment regulated
More informationTEST REPORT STIHL MS 441. OWNER OF THE TEST CERTIFICATE: Manufacturer and applicant: Andreas Stihl AG & Co KG Badstrasse
TEST REPORT STIHL MS 441 OWR OF THE TEST CERTIFICATE: Manufacturer and applicant: Andreas Stihl AG & Co KG Badstrasse 115 D-71336 Waiblingen www.stihl.de MS 441 C-Q with second chain brake Test Results
More informationPERFORMANCE OF A NEW ERA PONSSE ELK
PERFORMANCE OF A NEW ERA PONSSE ELK THE STRONGEST MACHINE OF ITS SIZE CLASS OFFERS PERFORMANCE AND AGILITY The new PONSSE Elk is evidently the most productive forwarder in its class size. Clearly increased
More informationIMIHV01 SQA Unit Code (HA68 04) Carry out routine commercial vehicle maintenance
Overview This NOS is about conducting routine examination, adjustment and replacement activities as part of the periodic maintenance of commercial vehicles. IMIHV01 1 Performance criteria You must be able
More informationSpecial Products Catalogue 2018 Visit our new website!
Special Products Catalogue 2018 Visit our new website! www.aams-salvarani.com Index ENTAM (European Network for Testing of Agricultural Machines) is the network constituted by the official testing stations
More informationUSER GUIDE incardoc ios
USER GUIDE incardoc ios OVERVIEW Use Smartphone for Quick View of the Car and Engine Main Parameters: Read real-time parameters: speed, rotation, timings, economy Read diagnostic trouble codes Clean trouble
More informationSITEMA PowerStroke. Technical Information TI-P12. 1 Function. 2 Applications. Mould Closing Devices series FSKP. Contents. Technical Information
Technical Information SITEMA PowerStroke FSP ocking, actuating and releasing by pneumatic pressure TI-P1-EN-0/016 English translation of German original Technical Information TI-P1 SITEMA PowerStroke Mould
More informationSTANDARD ONDUFIL TM MULTI-TURN SPRING WASHER RANGE
per turn RD0223S320025IX 22.0 18.0 2.0 x 0.25 3.5 3 5.8 3.0 4.0 1.4 RD0223S420025IX 4 7.8 4.0 4.0 1.0 RD0223S520025IX 5 9.6 4.3 4.0 0.7 RD0223S620025IX 6 11.0 5.0 4.0 0.7 RD0223S720025IX 7 12.7 5.8 4.0
More informationSILVAN AUSTRALIA PTY. LTD.
Instruction Manual MANRP50-5 Rev A 15/6/11 Weedpak Rakpak 12V Sprayer 50 Litre SILVAN AUSTRALIA PTY. LTD. ABN 48 099 851 144 VICTORIA (HEAD OFFICE) 244-264 Greens Rd, Dandenong South, 3175 Australia Telephone:
More informationGENERAL INFORMATION HYDRAULIC MOTORS ITALY
GENERAL INFORMATION INTERMOT produces RADIAL PISTON since 1985: our yearly production is more than 13.000 units which we sell all over the world through our agents and authorized sellers. Our motor range
More informationActions undertaken in France for the adaptation of tractors
Actions undertaken in France for the adaptation of tractors Milan 2015 T. LANGLE www.irstea.fr Speaker 2 Thierry LANGLE Mechanical engineer Head of the Team Performance and safety of Propelled Agricultural
More informationNSW Grain Harvest Management Scheme
NSW Grain Harvest Management Scheme October 2013 Contents 1. Introduction... 1 2. Summary... 1 3. Definitions... 3 4. Grain Harvest Management Scheme (GHMS)... 5 4.1. Scheme Objectives... 5 4.2. Scheme
More informationSTATUTORY INSTRUMENTS. S.I. No. 6 of 2013 ROAD TRAFFIC (LICENSING OF DRIVERS) (AMENDMENT) REGULATIONS 2013
STATUTORY INSTRUMENTS. S.I. No. 6 of 2013 ROAD TRAFFIC (LICENSING OF DRIVERS) (AMENDMENT) REGULATIONS 2013 2 [6] S.I. No. 6 of 2013 ROAD TRAFFIC (LICENSING OF DRIVERS) (AMENDMENT) REGULATIONS 2013 I, LEO
More information>01/2015-EN
>01/2015-EN 406039-05 1 2 A range that is quite simply impressive XT 100 XT 130 XT 160 XT 160H XT 210H XT 240H The new generation XT extends the boundaries of performance. With working widths of up to
More informationPEDESTRIAN STACKER S1.0, S1.2, S1.4, S1.6, S KG
PEDESTRIAN STACKER S1.0, S1.2, S1.4, S1.6, S2.0 1 000 2 000KG S1.0, S1.2, S1.4, S1.6, S2.0 DISTINGUISHING MARKS 1.1 Manufacturer (abbreviation) 1.2 Manufacturer s type designation 1.3 Drive: electric (battery
More informationInfluence of shot peening and superfinishing on gears as a repair tool of damaged faces of teeth generated by overheating when grinding.
Influence of shot peening and superfinishing on gears as a repair tool of damaged faces of teeth generated by overheating when grinding. J. Kritzler Metal Improvement Company, LLC.; Unna, Germany Abstract
More informationOperation manual Flexible pin type coupling according to KWN 22014
Operation manual Flexible pin type coupling according to KWN 22014 Author: Dipl.-Ing.. V. Hausdorf 24.01.2005 gez. V. Hausdorf Approved: Dr.-Ing. Ch. Spensberger 24.01.2005 gez. Dr.-Ing. Ch. Spensberger
More informationSECONDARY FUEL TESTING ARRANGEMENTS
SECONDARY FUEL TESTING ARRANGEMENTS SUMMARY DOCUMENT JULY 2010 Note: 1. This summary document has been produced by EirGrid for information only. Parties should base any decision or actions on the legally
More informationTHE NEW GENERATION COMPRESSOR
SA200 inside the GASVECTOR system Main specifications Designed to be installed either inside GASVECTOR modules or in service rooms, it can work in conjunction with an electric motor up to maximum 55 kw
More informationRevision of Directive 96/53/EC of 25 July 1996
Revision of Directive 96/53/EC of 25 July 1996 on the maximum authorised weights and dimension Petr Dolejsi Director Mobility and Sustainable Transport, ACEA The Automobile Industry in Europe Key figures
More informationA SIMPLIFIED TEST PROCEDURES FOR KNAPSACK (OPERATOR- CARRIED) SPRAYERS CHAN CHEE WAN
A SIMPLIFIED TEST PROCEDURES FOR KNAPSACK (OPERATOR- CARRIED) SPRAYERS CHAN CHEE WAN CONTENTS I. INTRODUCTION II. ANTAM (ESCAP -CSAM) APPROVED STATUS III. GUIDELINES ON STANDARDS AND TEST PROCEDURES IV.
More informationRAIMONDI. High pressure forged globe valves to guarantee the pressure envelope integrity on harsh services.
Fig. 6022-6025 RAIMONDI High pressure forged globe valves to guarantee the pressure envelope integrity on harsh services. Features Forged body materials of highest quality, all in compliance with ASME
More information650mA Phase Dimmable LED Driver
Installation Guide DGLC650C18PD PATENT PENDING REGISTERED DESIGN Designed in Australia to meet Australian Standards and installation conditions DIGINET.NET.AU Diginet Control Systems Pty Ltd ABN 89 095
More informationCOMMISSION REGULATION (EC)
L 191/26 Official Journal of the European Union 23.7.2009 COMMISSION REGULATION (EC) No 640/2009 of 22 July 2009 implementing Directive 2005/32/EC of the European Parliament and of the Council with regard
More information50 Hz. Z612, Z616, Z622 Z631, Z646, Z660 Series 6 SUBMERSIBLE ELECTRIC PUMPS. ErP 2009/125/EC
5 Hz Z612, Z616, Z622 Z631, Z646, Z66 Series 6 SUBMERSIBLE ELECTRIC PUMPS ErP 29/125/EC Cod. 1915991 Rev. D Ed.9/217 CONTENTS Hydraulic performance range...4 Series Specifications...5 Table of Materials...7
More informationTT COMPACT RANGE TT35 TT40 TT45
TT COMPACT RANGE TT35 TT40 TT45 Operator Environment - Designed with Functional Purpose Form follows function in the new TT Compact Range, with instruments clearly visible and all controls easily reachable.
More informationThe EU tire label drives continuous product improvements. We ve been supporting this for over 140 years.
The EU tire label drives continuous product improvements. We ve been supporting this for over 140 years. 2 3 The EU tire label is coming. asic information included on the EU tire label The European Parliament
More information(Acts whose publication is not obligatory) COUNCIL COUNCIL DIRECTIVE
12. 8. 74 Official Journal of the European Communities No L 221/ 1 II (Acts whose publication is not obligatory) COUNCIL COUNCIL DIRECTIVE of 22 July 1974 on the approximation of the laws of the Member
More informationMerkel Compact Seal S 8
Merkel Compact Seal S 8 Merkel Compact Seal S 8 Material Rubber head Fabric part Material Code Hardness Nitrile rubber NBR 70 NBR B209 70 Shore A Operating conditions Fig. 1 Merkel Compact Seal S 8 Product
More informationSIZING OF SOLAR GENERATOR
MULTI ISLAND is a water pumping system with power from photovoltaic panels. It is designed for use in water wells, irrigation systems, or the power supply network is not available, or when the user wishes
More informationFPT Industrial To Launch New R22 And Showcase Agricultural Solutions At Agritechnica
FPT Industrial To Launch New R22 And Showcase Agricultural Solutions At Agritechnica Turin, November 2013 Pioneer in powertrain technology, FPT Industrial will showcase its agricultural solutions at Agritechnica
More informationMULTICHANNEL ULTRASONIC FLOW METER AFLOWT UF
MULTICHANNEL ULTRASONIC FLOW METER AFLOWT UF VERSION UF-5xx d INSTALLATION MANUAL ISO 9001:2008 CONTENTS Page INTRODUCTION... 3 1. SAFETY INSTRUCTIONS... 4 2. MOUNTING PREPARATION... 4 3. MOUNTING REQUIREMENTS...
More informationSEQUENT 56: MULTIPOINT SEQUENTIAL INJECTION SYSTEM FOR CYLINDER VEHICLES FIELD OF APPLICATION
SEQUENT 56: MULTIPOINT SEQUENTIAL INJECTION SYSTEM FOR 5-6-8 CYLINDER VEHICLES FIELD OF APPLICATION Sequent 56 is the evolution of the multipoint injection system for LPG by BRC. New concept product, Sequent
More information