VERSA; CANNOT REMOVE KEY FROM IGNITION

Transcription

1 Classification: Reference: Date: EL NTB December 2, 2009 VERSA; CANNOT REMOVE KEY FROM IGNITION This bulletin supersedes NTB Discard all of its copies. APPLIED VEHICLE: Versa (C11) APPLIED TRANSMISSIONS: CVT and 4-Speed A/T IF YOU CONFIRM: The key cannot be removed from the ignition after the shift lever is engaged in P (Park) position. ACTION: Verify the key interlock cable is properly adjusted. If out of adjustment, adjust the cable by following the SERVICE PROCEDURE in this bulletin, starting on Page 3. If not out of adjustment, this bulletin does not apply. Refer to the Electronic Service Manual (ESM) for further diagnosis. NOTE: Do not confuse the key interlock cable with the shift control cable. Do not replace the shift selector assembly (shifter assembly) for this incident, if it should occur. CLAIMS INFORMATION Submit a Primary Part (PP) type line claim using the following claims coding: DESCRIPTION PFP OP CODE SYM DIA FRT Adjust Key Interlock Cable (1) JX14AA BD (1) Refer to the electronic parts catalog (FAST or equivalent) and use the appropriate Key Interlock Cable Assy part number as the Primary Failed Part (PFP). IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE (starting on Page 3) as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. 1/5

2 2/5 NTB09-137

3 SERVICE PROCEDURE WARNING: Set the parking brake before key interlock cable adjustment. 1. Place the selector lever in N (Neutral). 2. Remove the selector lever handle. Refer to the ESM as needed. 3. Remove the center console assembly. Refer to the ESM as needed. 4. Locate the components in Figure 1 (below) in the picture on Page Slide the slider (A) toward the casing cap (B) while pressing tabs (C) on the slider to separate the slider (A) from the adjust holder (D). See Figure Remove the casing cap (B; Figure1) from the cable bracket (D; Figure 2) on the shift selector assembly. 7. Remove the key interlock cable from the key interlock rod (E). See Figure 1. Figure 1 Figure 2 3/5 NTB09-137

4 ADJUSTMENT 1. Place the selector lever in P (Park). 2. Turn ignition switch to ACC or ON. 3. Check the key interlock cable for secure fit and proper routing to the key cylinder (no picture shown). 4. Turn ignition switch to LOCK position. 5. Temporarily install the adjust holder (A) to the key interlock rod (B). See Figure Install the casing cap (C) to the cable bracket (D) on the shift selector assembly. See Figure 3. Figure 3 CAUTION: Do not bend or twist the key interlock cable excessively when installing. After installing the key interlock cable to the cable bracket (D) on the shift selector assembly, make sure the casing cap (C) is firmly secured in the cable bracket (D) on the shift selector assembly. If the casing cap (C) is loose (less than 39.2 N [4.0 kg, 8.8 lbs] removing force), replace the key interlock cable. Do not apply any side to side force to key interlock rod (B) when sliding slider (A). 4/5 NTB09-137

5 7. Slide the slider (A) toward the key interlock rod (D). See Figure 4. This will securely connect the adjust holder (C) with the key interlock rod (D). CAUTION: Do not press the tabs when holding the slider (A). Do not apply any side-to-side force to the key interlock rod (D) when sliding the slider (A). Figure 4 8. Before reassembling the vehicle, check key interlock operation. 9. Install the center console assembly. Refer to the ESM as needed. 10. Install the selector lever knob. Refer to the ESM as needed. 11. Check shift lock system operation. 5/5 NTB09-137