ALTIMA V6 SEDAN AND PATHFINDER; JUDDER DURING LIGHT ACCELERATION
|
|
- Andrea McCoy
- 5 years ago
- Views:
Transcription
1 Classificatio n: Reference: Date: AT NTB September 10, ALTIMA V6 SEDAN AND PATHFINDER; JUDDER DURING LIGHT ACCELERATION APPLIED VEHICLES, VINS AND DATES: APPLIED TRANSMISSION: Altima Sedan (L33) with V-6 engine only Pathfinder (R52) CVT IF YOU CONFIRM When driving an Applied Vehicle a judder (shudder, single or multiple bumps or vibrations) happens during light acceleration, and all of the following when the issue occurs: Vehicle speed is between 5 and 35 mph. Throttle position is about 10%. When issue occurs, if more throttle is applied issue stops. No DTCs are stored. ACTION 1. To determine the root cause perform the Service Procedure starting on page Should reprogramming the TCM NOT resolve the concern, first verifying the vehicle s service history and then recording and analyzing the data with Consult III plus (C-III plus) as the symptom occurs is required to accurately determine the root cause of the incident, if it should occur. NOTE: This bulletin does not apply to a condition called fuel economy drone. If the customer describes their issue as a lugging or as a groan/drone at low speed this is a normal condition to maximize fuel economy. Some customers will describe the condition as similar to a manual transmission vehicle in high gear at low speed. IMPORTANT: The purpose of "ACTION" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service Procedure as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. 1/20
2 FLOW CHART A Altima V-6 (L33) A Judder, Bump or Shock sensation is confirmed (low speed) Pathfinder (R52) Which vehicle? No Vehicle built before December 2012? Yes Reprogram the TCM and attempt duplication Yes Campaign NTB completed prior to 1,000 miles? Was the Issue duplicated? Yes Record the data using CIII plus Analyze CIII plus data No Replace the CVT No Procedure complete Is Judder Pressure Vibration or Lock Up Shock? Pressure Vibration Lock Up Shock Replace the CVT Replace the Torque Converter 2/20 NTB13-086
3 SERVICE PROCEDURE TCM Reprogramming NOTE: Most instructions for reprogramming with CONSULT-III plus (C-III plus) are displayed on the CONSULT PC screen. If you are not familiar with the reprogramming procedure, click here. This will link you to the "CONSULT- III plus (C-III plus) Reprogramming" general procedure. CAUTION: Connect a battery charger to the vehicle battery. If the vehicle battery voltage drops below 12.0V or rises above 15.5V during reprogramming, the TCM may be damaged. Be sure to turn OFF all vehicle electrical loads. If a vehicle electrical load remains ON, the TCM may be damaged. Be sure to connect the AC Adapter. If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted and the TCM may be damaged. Turn off all external Bluetooth devices (e.g., cell phones, printers, etc.) within range of the CONSULT PC and the VI. If Bluetooth signal waves are within range of the CONSULT PC during reprogramming, reprogramming may be interrupted and the TCM may be damaged. 3/20 NTB13-086
4 1. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure. 2. Start CONSULT-III (C-III) plus. 3. Wait for the plus VI to be recognized. The serial number will display when the plus VI is recognized. 4. Select Re/programming, Configuration. VI is recognized Step 4 Figure 1 5. Follow the on-screen instructions and navigate the C-III plus to the screen shown in Figure 2 on the next page. 4/20 NTB13-086
5 6. When you get to the screen shown in Figure 2, confirm this bulletin applies as follows. A. Find the TCM Part Number and write it on the repair order. NOTE: This is the current TCM Part Number (P/N). 6A: Current TCM P/N TRANSMISSION Figure 2 B. Compare the P/N you wrote down to the numbers in the Current TCM Part Number column in Table A below. If there is a match, this reprogramming applies. Continue with the reprogramming procedure. If there is not a match, this reprogramming is not needed. Table A Model Altima Sedan (L33) Pathfinder (R52) Model Year Current TCM Part Number Before Reprogramming: MY 13-14MY 3NT0A, 3TA6A 3KA2A 3KD2A 3KA4A, 3KA4B 3KD4A, 3KD4B 5/20 NTB13-086
6 7. Follow the on-screen instructions to navigate C-III plus and reprogram the TCM. NOTE: In some cases, more than one new P/N for reprogramming is available. In this case, the screen in Figure 3 displays. Select and use the reprogramming option that does not have the message Caution! Use ONLY with NTBXX-XXX. If you get this screen and it is blank (no reprogramming listed), it means there is no reprogramming available for this vehicle. Close C-III plus and refer back to ASIST for further diagnosis. IMPORTANT: If C-III plus locks up or freezes at this point or displays cannot complete reprogramming, the CONSULT PC is set up with User Rights. Reprogramming can be completed with Administrator log in, the TOUGHBOOK settings need to be changed so that Users have full access rights. See your Dealership s IT System Administrator for details. TRANSMISSION Figure 3 6/20 NTB13-086
7 8. When the screen in Figure 4 displays, reprogramming is complete. NOTE: If the screen in Figure 4 does not display (reprogramming does not complete), refer to the information on the next page. 9. Disconnect the battery charger from the vehicle. 10. Select Next. Figure 4 Step 10 NOTE: In the next step (page 9), you will perform Erase All DTCs. DTC erase is required before C-III plus will provide the final reprogramming confirmation report. 7/20 NTB13-086
8 TCM recovery: Do not disconnect plus VI or shut down C-III plus if reprogramming does not complete. If reprogramming does not complete and the!? icon displays as shown in Figure 5: Check battery voltage ( V). Ignition is ON, engine OFF. External Bluetooth devices are OFF. All electrical loads are OFF. Select retry and follow the on screen instructions. Retry may not go through on first attempt and can be selected more than once. Figure 5 If reprogramming does not complete and the X icon displays as shown in Figure 6: Check battery voltage ( V). CONSULT A/C adapter is plugged in. Ignition is ON, engine OFF. Transmission is in Park. All C-III plus / VI cables are securely connected. All C-III plus updates are installed. Select Home, and restart the reprogram procedure from the beginning. Figure 6 8/20 NTB13-086
9 11. Follow the on-screen instructions to Erase All DTCs. 12. When the entire reprogramming process is complete, the screen in Figure 7 will display. 13. Verify the before and after part numbers are different. 14. Print a copy of this screen (Figure 7) and attach it to the repair order for warranty documentation. 15. Select Confirm. Step _ _ TRANSMISSION Step 14 Step 15 Figure Close C-III plus. 17. Turn the ignition OFF. 18. Disconnect the plus VI from the vehicle. 19. Make sure the vehicle operates correctly and the MIL is OFF. 9/20 NTB13-086
10 Recording and analyzing data during judder incident using C-III plus to confirm root cause Configuring CIII plus 1. Open C-III plus, connect the VI and then select Diagnosis (One System). 2. Select TRANSMISSION and then DATA MONITOR (Figure 8). 3. Select Clear Monitor Item. 4. Select Setting button: 3. Select Clear Monitor Item 4. Select Setting Figure 8 10/20 NTB13-086
11 5. Under setting, select settings shown in Figure 9. Manual trigger. And then: Recording Time: 10sec. Sampling Rate: 10msec. Trigger Point (Pre/post): Pre-Trigger 80% Post-Trigger 20% Step 5 6. Select Confirm Figure 9 6. Select Confirm to save the new Recording Conditions as the default. 11/20 NTB13-086
12 7. Select these 5 monitored signals ONLY from Monitor Menu and then select START when ready. INPUT REV SEC SPEED ENG SPEED SEC PRESSURE PRI PRESSURE IMPORTANT: For this Service Procedure, select only the signals in step 7. Use arrow to roll to the next page for more monitored signals Figure 10 12/20 NTB13-086
13 8. Perform the customer s described driving conditions to see if the judder incident can be duplicated. Once duplicated, immediately record the data with the C-III plus that was set up in steps 1-7 as the issue occurs. Save and Review Recorded Data 9. After the C-III plus data has been recorded with DATA MONITOR, save the data file as FlyingGraph(last 8 of VIN).txt file (example: FlyingGraphEM txt file) onto the Consult PC desktop as shown in Figure 11. NOTE: The Flying Graph software is available on the desktop of your Consult PC. It can be used for the data review. Data files must be saved as.txt file type before it can be used with the Flying Graph application. Refer to Figure 11 below for example. For an illustration of the C-III plus desktop shortcut to the Flying Graph application see Figure 12 on the next page. Select Save first and then name the file Save the recorded data as a.txt file onto the Consult PC desktop so that it can be viewed with the Flying Graph application. Figure 11 13/20 NTB13-086
14 10. Open the.txt file saved to the Consult PC desktop in step 9 by dragging the text file on the desktop over the icon for the Flying Graph application (see Figure 12 below). Drag this icon over the Flying Graph application icon to open the file Figure 12 14/20 NTB13-086
15 11 The Flying Graph will initially display only four (4) data channels. To display the 5 th recorded channel, right click to the left of the data channel not visible (see Figure 13) and click on Add graph to display the graph. 12. Review the INPUT REV, SEC SPEED, ENG SPEED, PRI PRESSURE and SEC PRESSURE signals for signs of a Pressure Vibration. Figures 13 and 14 show reference examples of with and without a Pressure Vibration. Step 11. With mouse, right click here and select Add graph Vibrations also present in one or more speed signals These variations in PRI and SEC PRESSURE are a normal response to vehicle input. Figure 13 Repetitive Pressure Vibration in PRI and/or SEC Pressure signals. 15/20 NTB13-086
16 These variations in PRI and SEC PRESSURE are a normal response to vehicle input. Figure 14 NOTE: Figure 14 shows INPUT REV, SEC SPEED, ENG SPEED, PRI PRESSURE and SEC PRESSURE from a vehicle that does not have a judder present. 13. During data review, if your data shows a Repetitive Pressure Vibration in either PRI PRESSURE or SEC PRESSURE, and also shows an irregular (non-smooth) line in one or more speed signals (ENG SPEED, INPUT REV, SEC SPEED) as indicated in Figure 13, replace the CVT to resolve (Figure 13 shows Repetitive Pressure Vibrations circled in red). Do not replace the torque converter assembly if the data review shows Repetitive Pressure Vibration as described above. If a judder is present and the recorded data review shows that the data lines are smooth with no oscillations as shown in Figure 14 above refer to Torque Converter Replacement on page 17. NOTE: Refer to the appropriate section of the Electronic Service Manual (ESM) for the procedure to replace the CVT, as needed. If a judder is present, recorded data review does not indicate pressure vibration and the torque converter in the CVT is already D level or greater (see FLOW CHART B on page 17), refer to ASIST or the appropriate section of the ESM for further diagnostic assistance. 16/20 NTB13-086
17 FLOW CHART B Check the stamping on the outside of the torque converter 25B 25C 25D 25E Replace the Torque Converter DO NOT Replace the Torque Converter Serial Number Serial Number Less than or equal to: Greater than: Less than or equal to: Greater than: Replace the Torque Converter DO NOT Replace the Torque Converter Replace the Torque Converter DO NOT Replace the Torque Converter 17/20 NTB13-086
18 Torque Converter Replacement 1. Replace the torque converter with the new one listed in the Parts Information: Refer to the TM section of the appropriate Service Manual for replacement information. NOTE: Make sure the converter housing oil seal (front seal) is not damaged. If damaged, replace it. If the front seal is replaced, use special tool J (oil pump seal installer) to install and properly seat the seal. Make sure CVT fluid, as a lubricant, is applied to the front seal, torque converter snout, and input shaft o-ring seal before installation of the new torque converter. 18/20 NTB13-086
19 PARTS INFORMATION DESCRIPTION PART NUMBER QUANTITY Torque Converter (2) WX0D 1 CVT ASSEMBLY (1) 1 NS-3 CVT Fluid 999MP-NS300P (3) (1) Refer to the electronic parts catalog (FAST) for the correct CVT Assembly part number for the vehicle. (2) Due to limited supply, Part Number WX0D will be on restriction for several weeks after the publication date of this bulletin. If WX0D is needed during the restriction period, use the Parts Order Form attached to the last page of this bulletin. (3) As needed. NS-3 CVT Fluid can be ordered from the Maintenance Advantage website that can be accessed through (NNANET.COM, Parts & Service, Maintenance Advantage-Tire/Wiper/Battery/Chemical). CLAIMS INFORMATION Submit a Primary Part (PP) type line claim using the following claims coding: OR DESCRIPTION PFP OP CODE SYM DIA FRT Reprogram Transmission Control Module Diagnose Judder ** (1) JE99AA ZE 32 (2) JX25AA 1.0 Submit a Primary Part (PP) type line claim using the following claims coding: DESCRIPTION PFP OP CODE SYM DIA FRT Reprogram Transmission Control Module R&I Automatic CVT Transaxle Assy RPL Torque Converter Assy ** RPL Automatic CVT Transaxle Diagnose Judder ** (1) JE99AA JD01AA JD043A JD023A JX25AA BE 32 (1) Refer to Parts Information above and use the Torque Converter Part Number (31100-XXXXX) as the PFP. (2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat Rate Time. ** Use these operation codes only if need for the diagnosis and actual repair performed. (2) /20 NTB13-086
20 PARTS ORDER FORM for 2013 ALTIMA V6 SEDAN AND PATHFINDER SHUDDER FROM TORQUE CONVERTER LOCK UP CLUTCH INCOMPLETE ORDER FORMS WILL NOT BE PROCESSED Dealer Code: Order Date: Dealership Address: VIN Number: PDC: Sacramento PDC Orlando PDC Los Angeles PDC Chicago PDC Dallas PDC Greenville PDC Baltimore PDC Memphis Olive Branch PDC New York PDC Part Number Description Quantity WX0D Torque Converter Send the completed form to: to NOTE: This bulletin and Service Procedure is not a campaign. For convenience, the above address is being used to fulfill and expedite this part request. 20/20 NTB13-086
2013 ALTIMA V6 SEDAN AND PATHFINDER SHUDDER FROM TORQUE CONVERTER LOCK UP CLUTCH
Classification: Reference: Date: AT13-007a NTB13-064a June 13, 2013 2013 ALTIMA V6 SEDAN AND PATHFINDER SHUDDER FROM TORQUE CONVERTER LOCK UP CLUTCH This bulletin has been amended to correct a typographical
More information2013 ALTIMA SEDAN WITH 4 CYL ENGINE; MIL ON WITH A/F SENSOR DTC STORED
Classificatio n: Reference: Date: EC12-024b NTB12-085b April 4, 2013 2013 ALTIMA SEDAN WITH 4 CYL ENGINE; MIL ON WITH A/F SENSOR DTC STORED This bulletin has been amended in several areas to remove V6
More informationPATHFINDER, QUEST, MURANO, MAXIMA, ALTIMA V6 CVT JUDDER AND DTC P17F0 OR P17F1 STORED
Classification: Reference: Date: APPLIED VEHICLE: AT15-005b NTB15-015b September 10, 2015 PATHFINDER, QUEST, MURANO, MAXIMA, ALTIMA V6 CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended
More informationMIL ON WITH P0840/P0845 AND P0710
Classification: Reference: Date: AT09-002a NTB09-044a August 26, 2011 MIL ON WITH P0840/P0845 AND P0710 This bulletin has been amended. ACTIONS, the NOTE under PARTS INFORMATION, a portion of the repair
More informationALTIMA; CVT DELAYED ENGAGEMENT WHEN SHIFTING INTO DRIVE OR REVERSE
Classification: Reference: Date: AT15-014b NTB15-085b April 1, 2016 2013-2015 ALTIMA; CVT DELAYED ENGAGEMENT WHEN SHIFTING INTO DRIVE OR REVERSE This bulletin has been amended. Instructions have been changed
More informationMURANO; AUTOMATIC BACK DOOR DOES NOT OPERATE AND RELATED DTCS
Classification: Reference: Date: BT15-020b NTB15-073b March 22, 2016 2015-2016 MURANO; AUTOMATIC BACK DOOR DOES NOT OPERATE AND RELATED DTCS This bulletin has been amended. Changes have been made to all
More information2007 SENTRA & VERSA; DTC P0031, P2A00, P1148
Classification: Reference: Date: EC08-017a NTB08-074a April 27, 2009 2007 SENTRA & VERSA; DTC P0031, P2A00, P1148 This bulletin has been amended. The Claims Information and Service Procedure have been
More informationSENTRA; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC
Classification: Reference: Date: AT16-017 NTB16-113 November 15, 2016 2011-2012 SENTRA; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC APPLIED VEHICLE: APPLIED ENGINE: 2011-2012 Sentra
More information2007 G35; CRUISE CONTROL SYMPTOMS WHEN TRAVELING DOWNHILL
Classification: Reference: Date: EL07-022a ITB07-028a October 24, 2007 2007 G35; CRUISE CONTROL SYMPTOMS WHEN TRAVELING DOWNHILL The Applied VIN/Date, ACTION, Parts Information, Claims Information, Service
More information2007 MAXIMA; MIL 'ON' W/DTC P0840 OR P0845
Classification: Reference: Date: AT08-001 NTB08-042 April 3, 2008 2007 MAXIMA; MIL 'ON' W/DTC P0840 OR P0845 APPLIED VEHICLE: 2007 Maxima (A34) IF YOU CONFIRM The MIL is ON with one of the following DTC
More informationTechnical Bulletin. Reference: NTB15-087a CVT WITH 4 CYLINDER ENGINE VALVE BODY REPLACEMENT WITH CONFIRMED DTC
2014 Nissan-Datsun Altima Sedan L4-2.5L (QR25DE) Vehicle > ALL Diagnostic Trouble Codes ( DTC ) > Technical Service Bulletins CVT WITH 4 CYLINDER ENGINE VALVE BODY REPLACEMENT WITH CONFIRMED DTC Technical
More informationFRONTIER WITH QR25 ENGINE; DTC P0420 (TW CATALYST SYS-B1) STORED IN THE ECM
Classification: Reference: Date: EC10-008 NTB10-045 March 19, 2010 2005-2006 FRONTIER WITH QR25 ENGINE; DTC P0420 (TW CATALYST SYS-B1) STORED IN THE ECM APPLIED VEHICLE: 2005-2006 Frontier (D40) APPLIED
More informationALTIMA SEDAN, COUPE, AND HYBRID; ENGINE NO CRANK / NO START
Classification: Reference: Date: EL10-030 NTB10-139 November 23, 2010 ALTIMA SEDAN, COUPE, AND HYBRID; ENGINE NO CRANK / NO START APPLIED VEHICLES: 2007 2010 Altima Sedan (L32) with CVT only 2008 2010
More informationVERSA; CANNOT REMOVE KEY FROM IGNITION
Classification: Reference: Date: EL09-040 NTB09-137 December 2, 2009 VERSA; CANNOT REMOVE KEY FROM IGNITION This bulletin supersedes NTB08-071. Discard all of its copies. APPLIED VEHICLE: 2007 2010 Versa
More informationALTIMA; MIL ON P1273 (QR25 ENGINE) MAY BE CAUSED BY THE REAR O2 SENSOR
Classification: Reference: Date: EC05-016a NTB06-039a May 17, 2006 2004 2005 ALTIMA; MIL ON P1273 (QR25 ENGINE) MAY BE CAUSED BY THE REAR O2 SENSOR This bulletin has been amended. The Claims Information
More information2007 ALTIMA AND SENTRA; DTC P0128 THERMOSTAT FUNCTION
Classification: Reference: Date: EC07-001a NTB07-020a April 23, 2007 2007 ALTIMA AND SENTRA; DTC P0128 THERMOSTAT FUNCTION This bulletin has been amended. Applied Vehicles has been amended to exclude Altima
More information2004 TITAN AND ARMADA; MIL "ON" WITH DTC P1031, P1051, P1148, P1168 A/F SENSOR HEATER / CLOSED LOOP
Classification: Reference: Date: EC04-008a NTB04-032a October 29, 2004 2004 TITAN AND ARMADA; MIL "ON" WITH DTC P1031, P1051, P1148, P1168 A/F SENSOR HEATER / CLOSED LOOP This bulletin amends NTB04-032.
More informationROGUE AND ROGUE SELECT; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC
Classification: Reference: Date: AT16-013 NTB16-090 September 9, 2016 2011-2015 ROGUE AND ROGUE SELECT; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC APPLIED VEHICLES: 2011-2013 Rogue
More informationVOLUNTARY SAFETY RECALL CAMPAIGN QUEST FUEL PUMP CONTROL MODULE
Reference: NTB12-022a April 12, 2012 Date: VOLUNTARY SAFETY RECALL CAMPAIGN 2011-2012 QUEST FUEL PUMP CONTROL MODULE This bulletin has been amended. The NHTSA # and OWNER S LETTER have been added. Please
More informationI30 MIL "ON" WITH DTC P0420 STORED - THREE WAY CATALYST FUNCTION
Classification: Reference: Date: EC00-025b ITB00-054b June 7, 2004 2000-2001 I30 MIL "ON" WITH DTC P0420 STORED - THREE WAY CATALYST FUNCTION IMPORTANT: THIS BULLETIN HAS BEEN REVISED. The Service Information
More informationMIL ON WITH DTC P0106 STORED
Classification: Reference: Date: EC12-010f ITB12-026f March 15, 2016 MIL ON WITH DTC P0106 STORED This bulletin has been amended to edit the part numbers in Table A on page 5 and remove 2010 G37 Convertible
More informationG37, M37, M56, AND QX56; MIL ON WITH DTC P0106 STORED
Classification: Reference: Date: EC12-010d ITB12-026d June 6, 2013 G37, M37, M56, AND QX56; MIL ON WITH DTC P0106 STORED This bulletin has been amended. The ECM P/N Table has been updated. No other changes
More informationPROCEDURE TO COMPLETE IAVL WHEN IDLE SPEED NEEDS TO BE REDUCED.
Classification: Reference: Date: EC05-009 NTB05-067 October 5, 2005 PROCEDURE TO COMPLETE IAVL WHEN IDLE SPEED NEEDS TO BE REDUCED. APPLIED VEHICLES: All 2002 2005 models IF YOU CONFIRM The idle, in Park
More informationMAXIMA; ABS ACTIVATES WITH NORMAL BRAKING / ABS WARNING LAMP IS ON
Classification: Reference: Date: BR06-011b NTB07-016b July 10, 2007 2004 2007 MAXIMA; ABS ACTIVATES WITH NORMAL BRAKING / ABS WARNING LAMP IS ON The Parts Information section of this bulletin has been
More information2011 M; NO START AND / OR BATTERY LOW VOLTAGE DUE TO INTELLIGENT KEY AND WELCOME LIGHTING
Classification: Reference: Date: EL11-010 ITB11-029 May 2, 2011 2011 M; NO START AND / OR BATTERY LOW VOLTAGE DUE TO INTELLIGENT KEY AND WELCOME LIGHTING APPLIED VEHICLE : 2011 M37 and M56 (Y51) APPLIED
More information2009 MAXIMA STEERING COLUMN COMFORT ADJUSTMENT
Classification: Reference: Date: ST09-005 NTB09-094 September 23, 2009 2009 MAXIMA STEERING COLUMN COMFORT ADJUSTMENT APPLIED VEHICLES: 2009 Maxima (A35) IF YOU CONFIRM The steering column power adjustment
More informationEXHAUST RATTLE / BUZZING NOISE
Classification: Reference: Date: EM05-003e NTB05-021e March 10, 2010 EXHAUST RATTLE / BUZZING NOISE This bulletin has been amended. The title, ACTIONS, PARTS INFORMATION, and the SERVICE PROCEDURE have
More informationMAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD
Classification: Reference: Date: EL01-030d NTB02-001d December 21, 2004 2000-2003 MAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD This bulletin amends NTB02-001. The Applied Vehicles have
More informationGT-R MIL ON WITH DTC P0729/P2832 STORED
Classification: Reference: Date: AT10-006 NTB11-011 February 18, 2011 2009-2011 GT-R MIL ON WITH DTC P0729/P2832 STORED APPLIED VEHICLE: 2009 2011 GT-R (R35) IF YOU CONFIRM For 2009 - The MIL is on and
More informationSENTRA; LONG ENGINE CRANK TIME BEFORE START
Classification: Reference: Date: EC05-001a NTB05-052a September 8, 2006 2002 2006 SENTRA; LONG ENGINE CRANK TIME BEFORE START APPLIED VEHICLES: 2002 Sentra (B15) with QR25 engine only. 2003 2006 Sentra
More informationMAXIMA; MIL ON WITH DTC S P0014, P0024
Classificatio n: Reference: Date: EC12-026 NTB12-116 December 17, 2012 2009-2012 MAXIMA; MIL ON WITH DTC S P0014, P0024 APPLIED VEHICLE: 2009-2012 Maxima (A35) IF YOU CONFIRM MIL is on with DTC s P0014
More informationG35; CLICKING NOISE FROM REAR AXLES
Classification: Reference: Date: RA04-004b ITB05-002b November 9, 2005 2003 2005 G35; CLICKING NOISE FROM REAR AXLES This bulletin has been amended. The Service Procedure has been revised. No other content
More informationECM REPLACEMENT PROCEDURES
Classification: Reference: Date: EC00-007c NTB00-052c April 16, 2004 ECM REPLACEMENT PROCEDURES ATTENTION: THIS BULLETIN HAS BEEN REVISED. The Service Procedures for replacing an ECM on an Applied vehicle
More informationVOLUNTARY RECALL CAMPAIGN PASSENGER AIR BAG OCCUPANT CLASSIFICATION SYSTEM (OCS)
Reference: NTB08-095c December 4, 2008 Date: VOLUNTARY RECALL CAMPAIGN 2007 2009 PASSENGER AIR BAG OCCUPANT CLASSIFICATION SYSTEM (OCS) This bulletin has been amended. Instruction for the AC adapter has
More informationG COUPE AND SEDAN; BRAKE JUDDER
Classification: Reference: Date: BR09-002b ITB09-037b January 28, 2010 G COUPE AND SEDAN; BRAKE JUDDER This bulletin has been amended. CLAIMS INFORMATION has been corrected. The SERVICE PROCEDURE has been
More informationVOLUNTARY RECALL CAMPAIGN PASSENGER AIR BAG OCCUPANT CLASSIFICATION SYSTEM (OCS)
Reference: ITB08-045d December 4, 2008 Date: VOLUNTARY RECALL CAMPAIGN 2007 2008 PASSENGER AIR BAG OCCUPANT CLASSIFICATION SYSTEM (OCS) This bulletin has been amended. Instruction for the AC adapter has
More informationQX4; DRIVER'S SEAT (WITH ADP ONLY) WON'T MOVE FORWARD OR BACKWARD
Classification: Reference: Date BT00-030a ITB00-065a December 21, 2004 2001 2003 QX4; DRIVER'S SEAT (WITH ADP ONLY) WON'T MOVE FORWARD OR BACKWARD This bulletin amends ITB00-065. This version amends the
More informationMIL ON WITH DTC P0102/P1102 (MASS AIRFLOW SENSOR MAFS) STORED
Classification: Reference: Date: EC02-026 NTB02-109 November 5, 2002 MIL ON WITH DTC P0102/P1102 (MASS AIRFLOW SENSOR MAFS) STORED APPLIED VEHICLE: 2002 Maxima (A33) APPLIED DATE: Vehicles built before
More informationFX35; DTC P0300 AND IGNITION COILS BLISTERED
Classification: Reference: Date: EC11-007 ITB11-017 March 1, 2011 2003 2008 FX35; DTC P0300 AND IGNITION COILS BLISTERED APPLIED VEHICLES: 2003 2008 FX35 (S50) IF YOU CONFIRM Cylinder Misfire DTC (P0300
More informationVehicle Level Technical Service Bulletins All Technical Service Bulletins Engine Controls - Engine Idle Speed 25RPM Too High
Select Vehicle New TSBs Technician's Reference Component Search: Conversion Calculator 2005 Nissan-Datsun Maxima V6-3.5L (VQ35) Vehicle Level Technical Service Bulletins All Technical Service Bulletins
More informationSYSTEM READINESS TEST (SRT) DRIVE PATTERNS
Classification: Reference: Date: EC98-001c NTB98-018c January 3, 2002 SYSTEM READINESS TEST (SRT) DRIVE PATTERNS This amended version of NTB98-018b contains an updated Service Procedure and updated ECM
More informationMAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD TECHNICAL SERVICE BULLETIN
Page 1 of 11 2000-2003 MAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD TECHNICAL SERVICE BULLETIN Reference Number(s): NTB02-001d, Date of Issue: December 21, 2004 NISSAN: 2000-2003 Maxima
More informationALTIMA SEDAN; SLIGHT DRIVER'S POWER SEAT MOVEMENT SIDE-TO-SIDE
Classification: Reference: Date: BT08-025b NTB08-089b November 12, 2009 2007-2010 ALTIMA SEDAN; SLIGHT DRIVER'S POWER SEAT MOVEMENT SIDE-TO-SIDE The ACTION statement, Applied Vehicles/VINs/Dates/, Parts
More informationSYSTEM READINESS TEST (SRT) DRIVE PATTERNS
Classification: Reference: Date: EC98-001f NTB98-018f November 7, 2012 SYSTEM READINESS TEST (SRT) DRIVE PATTERNS This bulletin has been amended. Several Changes were made on page 9. Please discard all
More informationSYSTEM READINESS TEST (SRT) DRIVE PATTERNS
Classification: Reference: D ate: EC98-001g NTB98-018g June 7, 2013 SYSTEM READINESS TEST (SRT) DRIVE PATTERNS This bulletin has been amended. Additional changes were made on page 9. Please discard all
More informationService Bulletin
Service Bulletin 05-019 Applies To: 2001 02 MDX ALL February 5, 2008 Warranty Extension: EGR Valve Contamination May Cause Engine Hesitation/Surge or DTC P1491 (Supersedes 05-019, dated July 20, 2005,
More informationMAXIMA MIL "ON" WITH FRONT O2 SENSOR DTC P0134, P0135, P0154, OR P0155
Classification: Reference: Date: EC01-029 NTB02-002 January 1, 2002 2000-2001 MAXIMA MIL "ON" WITH FRONT O2 SENSOR DTC P0134, P0135, P0154, OR P0155 APPLIED VEHICLES: 2000-2001 Maxima (A33) SERVICE INFORMATION
More informationEX35, G35, G37; STEERING WHEEL SWITCH FINISHER SERVICE PARTS
Classification: Reference: Date: ST12-006 ITB12-050 August 14, 2012 EX35, G35, G37; STEERING WHEEL SWITCH FINISHER SERVICE PARTS APPLIED VEHICLES: 2007-2008 G35 Sedan (V36) 2009-2012 G37 Sedan (V36) 2008-2013
More informationEM06-004b NTB06-072b September 3, 2009 DRIVE BELT NOISE
Classification: Reference: Date: EM06-004b NTB06-072b September 3, 2009 DRIVE BELT NOISE This bulletin has been amended. The Service Procedure, Applied Vehicles / VIN / Date, ACTION, and Claims Information
More informationTECHNICAL SERVICE BULLETIN
GROUP ENG MODEL 2015MY K900 (KH) NUMBER DATE 141 (REV 1, 04/25/2014) April 2014 TECHNICAL SERVICE BULLETIN This bulletin has been revised to include additional information. New/revised sections of this
More informationCLUNK, RATTLE, OR KNOCKING NOISE FROM REAR BRAKE CALIPER
Classification: Reference: Date BR01-001A NTB01-069A March 7, 2002 CLUNK, RATTLE, OR KNOCKING NOISE FROM REAR BRAKE CALIPER This bulletin amends NTB01-069. This version includes additional Model and Model
More informationSUNROOF RAIL ASSEMBLY REPAIR
Classification: Reference: Date: BT99-049 NTB00-001 December 15, 1999 SUNROOF RAIL ASSEMBLY REPAIR APPLIED VEHICLES: 1995-97 Maxima (A32) 1996-99 Pathfinder (R50) SERVICE INFORMATION If an applied vehicle
More informationService Bulletin
Service Bulletin 16-012 December 1, 2016 05312 Version 3 Transmission Function Improvements: Sensation of Surge While Braking, Slow Downshift Response at Low Engine Speeds, DTC P2638 and Other Listed Symptoms
More informationFixed Right First Time. Volvo Technicians, Service and Parts Managers
Tech-Net Notes Fixed Right First Time Volvo Technicians, Service and Parts Managers NO: 25-19 DATE: 6-30-2004 MODEL: 960-S/V90/850/S70/V70/C70 M. YEAR: 1996-1998 SUBJECT: Establishing Readiness for OBD
More informationTECHNICAL SERVICE BULLETIN
GROUP CHA MODEL 2014~2015MY Forte (YD) 2014MY Sportage (SL) NUMBER DATE 065 (REV 3, 06/29/2016) February 2016 TECHNICAL SERVICE BULLETIN This bulletin has been revised to include additional information.
More informationTECHNICAL SERVICE BULLETIN
File Under: x GROUP FUEL NUMBER Circulate To: General Manager Service Manager Parts Manager x Service Advisor(s) x x x x MODEL 2014MY Forte (YD) w/2.0l GDI DATE 027 (REV 1, 11/15/2013) November
More informationMAXIMA A/T SHIFT CONTROL DEVICE - HARD TO SHIFT
Classification: Reference: Date: AT99-001a NTB99-014a June 19, 2000 1998-1999 MAXIMA A/T SHIFT CONTROL DEVICE - HARD TO SHIFT This bulletin amends NTB99-014 and includes updated Service and Warranty Information.
More informationTELEMATICS SERVICE INFORMATION
Classification: Reference: Date: EL15-006g NTB15-049g March 21, 2016 TELEMATICS SERVICE INFORMATION This bulletin has been amended. The service information and procedures have been revised. Please discard
More informationQUEST; REVISED SLIDING DOOR INITIALIZATION PROCEDURE
Classification: Reference: Date: BT04-043 NTB04-125 October 26, 2004 2004-2005 QUEST; REVISED SLIDING DOOR INITIALIZATION PROCEDURE APPLIED VEHICLES: 2004 2005 Quest (V42) with power sliding doors. IF
More informationGT-R RATTLE FROM FLYWHEEL HOUSING
Classification: Reference: Date: AT09-010 NTB09-147 December 18, 2009 2009 2010 GT-R RATTLE FROM FLYWHEEL HOUSING APPLIED VEHICLES: 2009 2010 GT-R (R35) IF YOU CONFIRM A rattle noise coming directly from
More informationService Bulletin Immobilizer System (Type 6) (Supersedes , dated February 20, 2009; see REVISION SUMMARY) February 22, 2013
Service Bulletin 06-033 Applies To: 2007-09 MDX ALL 2007-12 RDX ALL February 22, 2013 Immobilizer System (Type 6) (Supersedes 06-033, dated February 20, 2009; see REVISION SUMMARY) REVISION SUMMARY This
More informationTitle: TCM CALIBRATION UPDATE: M.I.L. ON DTC P2716 Models: 07 Camry (2GR -FE, 6 -Speed A/T)
Technical Service BULLETIN December 12, 2006 Title: TCM CALIBRATION UPDATE: M.I.L. ON DTC P2716 Models: 07 Camry (2GR -FE, 6 -Speed A/T) TSB REVISION NOTICE: S January 12, 2007: Production Change has been
More informationPATHFINDER / XTERRA / FRONTIER; BUZZING / WHINING NOISE FROM TIMING CHAIN AREA
Classification: Reference: Date: EM09-007a NTB09-128a May 25, 2010 PATHFINDER / XTERRA / FRONTIER; BUZZING / WHINING NOISE FROM TIMING CHAIN AREA This bulletin has been amended. PARTS INFORMATION and CLAIMS
More informationSUBJECT: Mazda Service Program (MSP) CX-5, Mazda6, CX-9, 2013 Mazda3 TomTom Navigation System Software Update
TO: Mazda Dealership Service Managers DATE: January 2014 SUBJECT: Mazda Service Program (MSP) 42 2013-2014 CX-5, 2014-2015 Mazda6, 2013-2014 CX-9, 2013 Mazda3 TomTom Navigation System Software Update Mazda
More informationService Bulletin
Service Bulletin 17-015 September 6, 2017 07188 Version 2 8-Speed Transmission (DCT) Has a Bump or Hard Shift When Coming to a Stop Supersedes 17-015, dated April 26, 2017, to revise the information highlighted
More informationService Bulletin
Service Bulletin 16-062 February 11, 2017 05595 Version 2 2012 15 MDX: Judder from the Torque Converter Lock-Up Clutch Supersedes 16-062, dated November 2, 2016, see REVISION SUMMARY AFFECTED VEHICLES
More informationALIGNMENT AND ROAD CROWN
Classification: Reference: Date: ST08-001 NTB08-097 October 9, 2008 ALIGNMENT AND ROAD CROWN APPLIED VEHICLES: All Nissan - except GT-R SERVICE INFORMATION Customers may report that their vehicle pulls
More informationService Bulletin
Service Bulletin 16-062 November 2, 2016 05121 Version 1 2014 15 MDX: Judder from the Torque Converter Lock-Up Clutch AFFECTED VEHICLES Year Model Trim VIN Range 2014 15 MDX ALL ALL BACKGROUND A judder
More informationService Bulletin
Service Bulletin 17-014 February 27, 2018 08343 Version 2 2016 17 Pilot: Judder from the Torque Converter Lock-Up Clutch (Snapshot Upload Required) Supersedes 17-014, 2016 17 Pilot: Judder from the Torque
More informationDrivetrain Binding/Tires Scrubbing During Low Speed Maneuvering, ESP Light in Instrument Cluster ON or Flashing
Condition Drivetrain Binding/Tires Scrubbing During Low Speed Maneuvering, ESP Light in Instrument Cluster ON or Flashing During low speed turns/maneuvering, vehicle drivetrain feels as if it is binding
More informationWITHOUT NAVIGATION SYSTEM HANDS-FREE PHONE POOR SOUND QUALITY
Classification: Reference: Date: EL12-064b ITB12-062b October 25, 2012 WITHOUT NAVIGATION SYSTEM HANDS-FREE PHONE POOR SOUND QUALITY This bulletin has been amended. Changes have been made throughout to
More informationCVT RE0F09B TCM P1701 TCM. Description
2012 Nissan-Datsun Altima L4-2.5L (QR25DE) Vehicle > ALL Diagnostic Trouble Codes ( DTC ) > Testing and Inspection > P Code Charts > P1701 CVT RE0F09B TCM P1701 TCM Description When the power supply to
More informationTHE StarSCAN FLASH FILES FOR THIS BULLETIN MUST BE RETRIEVED FROM THE INTERNET.
NUMBER: GROUP: 18-006-08 REV. A Vehicle Performance DATE: April 8, 2008 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be
More informationALL NISSAN; BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR
Classification: Reference: Date: BR00-004e NTB00-033e July 23, 2013 ALL NISSAN; BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR This bulletin has been amended to include vehicles built up to the publication
More informationTHE StarSCAN FLASH FILES FOR THIS BULLETIN MUST BE RETRIEVED FROM THE INTERNET. StarSCAN SOFTWARE LEVEL MUST BE AT RELEASE 8.03 OR HIGHER.
NUMBER: GROUP: 21-002-07 REV. E Transmission DATE: December 21, 2007 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
More informationTechnical Service Bulletin
17 Oil pressure light on and/or rattle noise from engine at cold start 17 08 23 2015411/6 November 21, 2008. Supersedes Technical Service Bulletin Group 17 number 08-05 dated July 22, 2008 for reasons
More informationTitle: M.I.L. ON DTC P3191, P3190, AND/OR P0A0F Models:
Technical Service BULLETIN October 18, 2004 Title: M.I.L. ON DTC P3191, P3190, AND/OR P0A0F Models: 04-05 Prius EG047-04 ENGINE TSB REVISION NOTICE: S February 22, 2005: Applicable Vehicles has been updated
More informationTechnical Service Bulletin
SUBJECT: group model Engine Sorento (XM) 2.4L GDI 2013MY NUMBER DATE 126 [Rev 1, 12/11/12] November 2012 Technical Service Bulletin This bulletin has been revised to include additional information. New/revised
More informationTITAN AND ARMADA DRIVER SIDE AIR MIX DOOR MOTOR REPLACEMENT
Classification: Reference: Date: HA11-004 NTB11-048 May 5, 2011 2004 2011 TITAN AND ARMADA DRIVER SIDE AIR MIX DOOR MOTOR REPLACEMENT APPLIED VEHICLE: 2004 2011 Titan (A60) 2004 2011 Armada (TA60) IF YOU
More informationLOW TIRE PRESSURE WARNING SYSTEM; BULLETINS SUMMARY
Classification: Reference: Date: WT13-006 ITB13-039 September 26, 2013 LOW TIRE PRESSURE WARNING SYSTEM; BULLETINS SUMMARY APPLIED VEHICLES: All vehicles with: Tire Pressure Monitor System (TPMS) Or Low
More informationVOLUNTARY SERVICE CAMPAIGN
GROUP Service Campaign NUMBER MODEL 2015 MY Sedona (YP) (EX, SX & SXL) DATE SC109 (REV 1, 12/19/2014) December 2014 VOLUNTARY SERVICE CAMPAIGN This bulletin has been revised to include additional information.
More informationService Bulletin
Service Bulletin 05-026 Applies To: 1999 02 Odyssey ALL 2003 Odyssey From VIN 2HKRL18..3H500001 thru 2HKRL18..3H504511 and from VIN 5FNRL18..3B000001 thru 5FNRL18..3B067057 2003 Pilot From VIN 2HKYF18..3H500001
More informationVO LUNTARY SERVIC E C AMPAIG N
2013 Sorento Report a problem with this article GROUP Service Campaign NUMBER MODEL 2011~13MY Sorento (XMa) DATE SC106 May 2014 VO LUNTARY SERVIC E C AMPAIG N This bulletin provides information related
More informationTechnical Service Bulletin
Subject Date AUTOMATIC TRANSAXLE ECM & TCM UPDATE Model MAY, 2010 2009~10 SONATA (NF) 2.4L [X] PARTS MANAGER [X] TECHNICIAN CIRCULATE TO: [ ] GENERAL MANAGER [X] SERVICE ADVISOR [X] SERVICE MANAGER [X]
More informationTECHNICAL BULLETIN JTB00230NAS2 28 JAN 2013
TECHNICAL BULLETIN JTB00230NAS2 28 JAN 2013 Jaguar Land Rover North America, LLC NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge,
More informationVibration Between MPH
T-SB-0069-08 Rev1 May 21, 2008 Service Category Engine/Hybrid System Section Engine Control Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2007 2009 Camry Engine(s): 2AZ Transmission(s):
More informationUSER GUIDE 1 USER GUIDE
USER GUIDE 1 USER GUIDE 1 TABLE OF CONTENTS IN THE BOX...3 NAVIGATING THE MENUS...3 MENU LAYOUT...3 UPDATE YOUR PROGRAMMER...4 CONNECT WITH THE MOTORCYCLE...5 TUNE YOUR MOTORCYCLE...6 ADDITIONAL FEATURES...8
More informationTechnical Information
Technical Service 2/14 ENU WE02 9 WE02 - Re-programming Instrument Cluster (Workshop Campaign) Important Note: CRITICAL WARNING - THIS CAMPAIGN INCLUDES STEPS WHERE SEVERAL CONTROL UNITS IN THE VEHICLE
More informationReference Guide and Step-by-Step Installation Manual
Reference Guide and Step-by-Step Installation Manual Some adjustable features listed on the following pages are NOT applicable for all applications. The year, make, and model of the vehicle will determine
More informationTechnical Service Bulletin
Technical Service Bulletin Group Number TRANSAXLE 07-40-009-1 Subject AUTOMATIC TRANSAXLE HARSH AND/OR DELAYED ENGAGEMENT INTO DRIVE OR REVERSE Date Model [X] PARTS MANAGER SEPTEMBER, 2007 1999~SONATA,
More informationOVERVIEW: This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software.
NUMBER: 21 001 18 GROUP: 21 Transmission and Transfer Case DATE: January 4, 2018 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication
More informationINFINITI; CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART
Classification: Reference: Date: EL13-010 ITB13-006 March 22, 2013 2005-2013 INFINITI; CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART APPLIED VEHICLES: All 2005 2013MY Infiniti Vehicles SERVICE INFORMATION
More informationALL INFINITI; BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR
Classification: Reference: Date: BR00-005e ITB00-024e August 8, 2007 ALL INFINITI; BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR This bulletin has been amended. The Applied Vehicles have been updated.
More informationRevised October 2014 Dealer Service Instructions for: Customer Satisfaction Notification P56 Reprogram Transmission Control Module
Revised October 2014 Dealer Service Instructions for: Customer Satisfaction Notification P56 NOTE: Labor operation numbers for the related operations have been revised. Models 2014-2015 (KL) Jeep Cherokee
More informationService Bulletin. Rough Idle at Cold Start; MIL Comes On With DTC P0107 or P0108 (Supersedes , dated March 5, 2004)
Applies To: 1998 02 Accord V6 ALL 1996 00 Civic DX, LX ALL 1999 00 Odyssey ALL Service Bulletin 04-004 August 10, 2004 Rough Idle at Cold Start; MIL Comes On With DTC P0107 or P0108 (Supersedes 04-004,
More informationTHE StarSCAN FLASH FILES FOR THIS BULLETIN MUST BE RETRIEVED FROM THE INTERNET.
NUMBER: GROUP: 18-003-07 REV. A Vehicle Performance DATE: March 7, 2007 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be
More information2003 G35 SEDAN; NOISE FROM ENGINE AREA WITH A/C ON
Classification: Reference: Date: HA02-005b ITB02-056b December 5, 2003 2003 G35 SEDAN; NOISE FROM ENGINE AREA WITH A/C ON This bulletin contains amended Applied VIN. Please discard all previous copies
More informationComputers and Control Systems: Monitors, Trips, Drive Cycles and Readiness Codes
1998 Volvo V70 AWD L5-2.4L Turbo VIN 56 B5254T Page 1 Computers and Control Systems: Monitors, Trips, Drive Cycles and Readiness Codes Generic Drive Cycle Readiness Code Resetting Procedure (Generic Drive
More informationSteering Angle Sensor (SAS) Replacement on Vehicles Equipped with Electronic Stability Control (ESC)
Revised 09-18 Technical Bulletin Steering Angle Sensor (SAS) Replacement on Vehicles Equipped with Electronic Stability Control (ESC) Revised 1 Technical 09-18 Bulletin Hazard Alert Messages Read and observe
More information9/11/2017 General Information (12) > [BOD051] Service Action: Power Tailgate IPM Update To Prevent Battery Discharge 2006 Kia Sedona MotoLogic
GROUP MODEL Body Sedona (VQ) w/power Tailgate NUMBER DATE 051 REVISED December 2009 This revised bulletin a BLACK BAR to the left of the procedure (as shown here) indicates REVISED instruction provides
More information