Operating Manual. Hausted Video imaging Chairs Models: ViC329 & ViC429 GFH RevB13 GF HEALTH PRODUCTS, INC.

Transcription

1 Operating Manua Hausted Video imaging Chairs Modes: ViC329 & ViC429 GFH RevB13 GF HEALTH PRODUCTS, INC.

2 WARNING - COPYING PROHIBITED this manua is protected by Federa Copyright aw, which provides for damages of up to usd $20000, as we as crimina fines and imprisonment, for unauthorized copying.

3 a word FrOM GF HEALTH PRODUCTS, INC. this manua contains important information on proper use and maintenance of the Hausted Video imaging Chair (ViC). a personne invoved in the use and maintenance of this equipment must carefuy review and compy with the warnings, cautions and instructions contained in this manua. these instructions are important to protect the heath and safety of personne operating a Video imaging Chair and shoud be retained in a convenienty accessibe area for quick reference. Compete instructions for uncrating and connecting utiities, as we as equipment drawings, have been furnished. if missing, contact GF Heath Products, Inc. for repacement copies, giving the seria number and mode number of the unit. We carry a compete ine of accessories for use with this chair. a GF representative wi gady review these with you. advisory a isting of the safety precautions to be observed when operating and servicing this equipment can be found in Section 1 of this manua. Do not operate or service the equipment unti you have become famiiar with this information. any ateration of this equipment not authorized by GF Heath Products, Inc., which coud affect its operation, wi void the warranty, coud vioate nationa, state, and oca reguations, and coud jeopardize your insurance coverage. indications for use the Hausted eectric powered Chairs are intended for use in patient treatment, transport or recovery. Service information a thorough preventive maintenance program is essentia to safe and proper unit operation. this manua contains maintenance schedues and procedures which shoud be foowed for satisfactory equipment performance. We encourag you to contact GF Heath Products, Inc. with any maintenance concerns GF Heath Products, Inc. a rights reserved printed in u.s.a. i

4 Manufactured by: GF Heath Products, Inc. 336 Trowbridge Drive Fond du Lac, WI Main Fax Cass 1 equipment type B equipment equipment not suitabe for use in the presence of a fammabe anesthetic mixture with air or oxygen or nitrous oxide. ipx4 (Spash-proof equipment) not suitabe for continuous operation (Duty Cyce: 10% six minutes in one hour) the base anguage of this document is engish. any transations must be made from the base anguage document. ii

5 tabe OF COntentS 1 isting of warnings and Cautions uncrating instructions Operating instructions Braking and Steering appying the Brakes reeasing the Brakes appying the Steering ock reeasing the Steering ock top adjustment raising the top owering the top recining the Chair Back independent eg Section independent Operation returning to Chair Mode adjustabe Footrest repositioning the Footrest Hinging rais repositioning the rai ViC Chair rotating instructions Mode Definitions non-transport Mode (anterior/posterior position) transport Mode (atera position) patient transfer instructions preventive Maintenance for the User Optiona accessories recommended repacement parts warranty iii

6 isting OF warnings and CautiOnS 1 the foowing is a isting of the safety precautions which must be observed when operating and servicing this equipment. warnings indicate the potentia for danger to personne, and CautiOnS indicate the potentia for damage to equipment. these precautions are repeated (in whoe or in part), where appicabe, throughout the manua. warning aceration HaZarD: w hen cutting bands aways use a too specificay designed for that purpose. this wi hep to avoid persona injuries frequenty incurred when bands are cut and tension reeased. warnings persona injury HaZarD (See SeCtiOn 3): t he ViC chair has a warning abe on the back of the back section stating: Maximum patient weight 147 kiograms (325 bs.). t he ViC chair is not intended to repace a stretcher or a gurney. t he ViC chair has warning abes on both the head and foot end stating: Do not sit on end as tipping may occur. t he ViC chair has a warning abe on the foot rest stating: Do not stand on foot rest. w hen not in use, do not eave the ViC chair in a recine position. w hen patient is seated in the chair, the side rais shoud be up and the patient shoud be secured with restraint straps. p atient entry, egress and transfer from the ViC chair shoud aways be from the center side rai ocation with the side rai in the down position and brakes ocked. a t no time shoud the patient be permitted to enter or exit from the ends of the ViC chair when in partia or tota recine position. t he patient shoud be paced in a fuy upright position with chair in ow height when transporting patient. the patient shoud never be transported when the ViC is in a recined position. t he brakes shoud aways be appied when patient is not being transported. t he ViC chair has a warning abe on the top of the base cover that states: when chair is in the non-transport mode: patient must remain fuy upright; patient must never be recined; patient must never be eft unattended. WARNING NOTICE FOR CALIFORNIA CUSTOMERS- Caifornia Proposition 65 Warning: This product contains a chemica known to the State of Caifornia to cause cancer and reproductive or deveopmenta harm. 1-1

7 uncrating instructions 2 important - report any SHipping DaMage immediatey: inform shipper of any damages - eave carton intact. eave the equipment in the receiving area unti inspection is compete. CautiOn - possibe equipment DaMage: t his crate contains fragie expensive medica equipment. uncrate and hande carefuy. i f after uncrating the equipment you find any damage (no matter how sight), show it to your supervisor. warning - persona injury HaZarD: when cutting bands, aways use too specificay designed for that purpose. this wi hep avoid persona injuries frequenty incurred when bands are cut and tension is reeased. important: Foow each step in the order shown in these instructions. unpacking instructions: your Hausted equipment has been carefuy packed at our manufacturing pant to ensure safe shipment to your medica faciity. there are severa procedures you must foow to put your new equipment in service. these procedures ony take a few minutes to compete and are required to ensure proper operation of the equipment. 1. Cut the two bands around the shipping carton. 2. r emove the top haf of the carton and cut one side of the bottom haf. 3. remove the equipment from the carton. 4. Check to see if a features of the equipment work propery. if a the features work, advance to step 5. if any of the features of the equipment do not work propery, ca GF Heath Products, Inc. for service at: Cean the equipment using mid detergent to remove any dirt accumuated during shipment, and pace the equipment into service. 2-1

8 Operating instructions 3 warnings persona injury HaZarD: a. t he ViC chair has a warning abe on the back of the back section stating: Maximum patient weight 147 kiograms (325 bs.). B. t he ViC chair is not intended to repace a stretcher or a gurney. C. t he ViC chair has a warning abes on both the head and foot end stating: Do not sit on end as tipping may occur. D. t he ViC chair has a warning abe on the foot rest stating: Do not stand on foot rest. e. w hen not in use, do not eave the ViC chair in a recine position. F. w hen patient is seated in the chair, the side rais shoud be up and the patient shoud be secured with restraint straps. g. p atient entry, egress and transfer from the ViC chair shoud aways be from the center side rai ocation with the side rai in the down position and brakes ocked. H. a t no time shoud the patient be permitted to enter or exit from the ends of the ViC chair when in partia or tota recine position. i. t he patient shoud be paced in a fuy upright position with chair in ow height when transporting patient. the patient shoud never be transported when the ViC is in a recine position. J. t he brakes shoud aways be appied when patient is not being transported. K. t he ViC chair has a warning abe on the top of the base cover that states: when chair is in the non-transport mode: patient must remain fuy upright; patient must never be recined; patient must never be eft unattended. 3-1

9 Operating instructions 3 See warning C & H See warning a See warning F See warning i 22" 50" 22" 70.5" See warning F See Section 3.5 See warning B, F, H & i See Section " 24" 66.5" 31.5" See warning g & H See section 3.7 See warning K See Section 3.6 See warning g through J See Section 3.1 See Section 3.2 See warning D See Section 3.4 See Section 3.3 See warning C & H See warning g through J See Section

10 Operating instructions BraKing and Steering OperatiOn warning - persona injury HaZarD: patient entry, egress and transfer from the ViC chair shoud aways be from the center side rai ocation with the side rai in the down position and brakes ocked. t he brakes shoud aways be appied when patient is not being transported. Figure a ppying the Brakes the four whee centra braking system is activated by depressing the red peda at the foot end of the unit on the patients eft side (Figure 3-1). to fuy engage the brakes, the peda shoud be pressed to approximatey 45. a four caster shoud be ocked from swiveing and rotating r eeasing the Brakes Depress the green peda at the head end of the unit on the patients eft, unti the peda is in a horizonta position (Figure 3-2). a four whees shoud rotate and swive freey. Figure 3-2 Figure appying the Steering ock From the head end of the ViC chair, depress the green peda downward into ocked position (Figure 3-3). push the ViC chair forward one caster at the foot end wi ock into a non-swive mode. this aows straight steering by the attendant, when pushing from the head end reeasing the Steering ock Depress the red peda at either of the right 3-3 side corners of the unit, unti the peda is in a horizonta position (Figure 3-2). a four whees shoud rotate and swive freey.

11 Operating instructions top adjustment warning - persona injury HaZarD: when not in use, do not eave the ViC chair in a recine position. a t no time shoud the patient be permitted to enter or exit from the ends of the ViC chair when in partia or tota recine position. Figure 3-4 t he patient shoud be paced in a fuy upright position with chair in ow height when transporting patient. t he patient shoud never be transported when the ViC is in a recine position. Figure 3-5 t he ViC chair has a warning abe on the top of the base cover that states: when chair is in the non-transport mode: patient must remain fuy upright; patient must never be recined; patient must never be eft unattended raising the top press the pump peda (peda nearest the head end) to the foor (Figure 3-4), then reease the pressure on the peda. repeat this process unti desired height is obtained. use smooth strokes on pump peda to ensure patient comfort. Figure owering the top press down on the reease peda (peda nearest the foot end) (Figure 3-5) unti desired height is obtained. Figure recining the Chair Back Squeeze the green recine ever on the right side of the back section (Figure 3-6). push back on the back section unti it is at desired position, (Figure 3-7) position can vary from upright to 10 trendeendurg positions. note that chair has a degree indicator ocated on the ower back section on the right side of the chair. to pace back into upright position, squeeze the recine hande and ift up on the back section. 3-4

12 Operating instructions independent eg SeCtiOn warning - persona injury HaZarD: the ViC chair has a warning abe on the top of the base cover that states: when chair is in the non-transport mode: patient must remain fuy upright; patient must never be recined; patient must never be eft unattended. Figure i ndependent Operation Hod and support eg section by the bottom of the frame tube (Figure 3-8). pu out on the end of the red ever (Figure 3-8). rotate the ever cockwise whie positioning the eg section (Figure 3-9). Once desired position of the eg section is reached, reease the ever and the eg section wi be ridged (Figure 3-10). when the eg section is independent, it can be repositioned at any time by turning the ever cockwise (Figure 3-9). Figure 3-9 note: aways support the eg section when turning the red ever r eturning to Chair Mode Support the eg section, turn the ever countercockwise whie pushing in on the ever (Figure 3-11). the ever wi side inward to an inactive position. Once the ever is inactive, adjust the eg section unti it is in ine with the back section (Figure 3-12). it wi cick as it reengages with the back section. Figure 3-10 Figure 3-11 Figure

13 Operating instructions adjustabe FOOtreSt warning - persona injury HaZarD: the ViC chair has a warning abe on the top of the base cover that states: when chair is in the non-transport mode: patient must remain fuy upright; patient must never be recined; patient must never be eft unattended. Figure repositioning the Footrest the footrest has three positions; retracted, ower and the upper positions. with the pan in the retracted position pu out, on the handes on either side of pan (Figure 3-13). the footrest wi drop into the ower position (Figure 3-14). to pace the footrest into the upper position, grasp the handes on both sides of the pan. tit the pan up whie ifting (Figure 3-15). Once the pan is up a the way, tit the pan out unti it ocks into position (Figure 3-16). to return the footrest into the retracted position, tit the pan up whie etting it side down, if needed, (Figure 3-15), into the ower position (Figure 3-13), continue titing the footrest unti it is in the retracted position. Figure 3-14 Figure 3-15 Figure

14 Operating instructions Hinging rais warning - persona injury HaZarD: patient entry, egress and transfer from the ViC chair shoud aways be from the center side rai ocation with the side rai in the down position and brakes ocked. Figure repositioning the rai the ViC rai has two positions, up and down, both positions ock the rai into pace. to put the rai down, whie supporting the rai (Figure 3-17), squeeze the two red tabs under the seat (Figure 3-18). aow the rai to hinge a the way down unti it ocks into pace (Figure 3-19). to raise the rai, squeeze the two red tabs under the seat (Figure 3-18). ift the rai a the way up unti it ocks into pace. Figure 3-18 Figure

15 Operating instructions ViC CHair rotating instructions warning - persona injury HaZarD: when not in use, do not eave the ViC chair in a recine position. the patient shoud be paced in a fuy upright position with chair in ow height when transporting patient. the patient shoud never be transported when the ViC is in a recine position. rear View transport Mode (atera position) Mode Definitions See Figure transport mode is when green arrow by the seat ock knob is aigned with green arrow on the base and seat is ocked. non-transport mode is when chair seat has been ocked 90 countercockwise from transport mode. non-transport mode is to be used ony for performing cinica procedures. Side View the transport mode is when the green arrows on the seat and back section are aigned, the back section is in the fu upright position and the chair is in ow height. non-transport Mode anterior/posterior position non-transport Mode never recine Back Section when in the non-transort Mode Figure

16 Operating instructions ViC CHair rotating instructions warning - persona injury HaZarD: when chair is in the nontransport mode: patient must remain fuy upright; patient must never be recined; patient must never be eft unattended. t he brakes shoud aways be appied when patient is not being transported. t he patient shoud be paced in a fuy upright position with chair in ow height when transporting patient. the patient shoud never be transported when the ViC is in a recined position. Figure 3-21 Figure n on-transport (anterior/posterior position) ock the caster brakes (Figure 3-1). Secure patient in sitting position with restraints. eevate chair to maximum height (Figure 3-4). pu out on the seat ock knob (Figure 3-21) to reease ock. rotate chair countercockwise (Figure 3-22), unti it ocks into the non-transport mode (see Figure 3-20). 3-9

17 Operating instructions ViC CHair rotating instructions warning - persona injury HaZarD: the ViC chair is not intended to repace a stretcher or a gurney. t he patient shoud be paced in a fuy upright position with chair in ow height when transporting patient. the patient shoud never be transported when the ViC is in a recine position. w hen patient is seated in the chair, the side rais shoud be up and the patient shoud be secured with restraint straps transport Mode (atera position) pu out on the seat ock knob (Figure 3-21). rotate the chair cockwise 90 (Figure 3-23), unti it ocks into the transport mode (see Figure 3-20). insure the chair is ocked in the transport mode (see Figure 3-20) before transporting or recining the patient. the green arrow abe on the seat wi be in ine with the green arrow abe on the base (Figure 3-24). Figure 3-23 Figure

18 Operating instructions patient transfer instructions warnings persona injury HaZarD: Maximum patient weight 147 kiograms (325 bs.). t he ViC chair is not intended to repace a stretcher or a gurney. Do not sit on end as tipping may occur. Do not stand on foot rest. w hen not in use, do not eave the ViC chair in a recine position. w hen patient is seated in the chair, the side rais shoud be up and the patient shoud be secured with restraint straps. p atient entry, egress and transfer from the ViC chair shoud aways be from the center side rai ocation with the side rai in the down position and brakes ocked. a t no time shoud the patient be permitted to enter or exit from the ends of the ViC chair when in partia or tota recine position. t he patient shoud be paced in a fuy upright position with chair in ow height when transporting patient. the patient shoud never be transported when the ViC is in a recine position. t he brakes shoud aways be appied when patient is not being transported. w hen chair is in the nontransport mode: patient must remain fuy upright; patient must never be recined; patient must never be eft unattended. Definition of terms used in instructions Beow (See Figure 3-25) transfer side Secondary Patient Device the transfer side wi aways be ocated on the attendants right hand side, when standing at the patient s foot end of the device, facing the patient. ) VIC Chair the transfer side wi aways be ocated on the patents right hand side. transfer of patient from ViC Chair to a Secondary Device Patient Preparation 1. eave patient secured with restraint straps unti actua patient transfer is to begin Secondary Device Preparation 1. ock the caster brakes on secondary device. 2. pace device into owest vertica position. 3. eve patient surface to a horizonta pane. 4. ower patient rai on transfer side of device. VIC Chair Preparation 1. ensure chair is in the transport mode (see Section 3-6). 2. adjust chair height so the seat section is eve with patient surface of secondary device. 3. ower the patient side rai on the transfer side of the ViC chair. 4. Move the ViC chair so that both devices are facing one another on the specified transfer sides. 5. recine the ViC chair into horizonta pane. 6. Maneuver chair so the transfer sides of the two devices are making contact (imit transfer gap as much as possibe). 7. ock the ViC chair caster brakes. 3-11

19 Operating instructions patient transfer instructions Patient Transfer 1. reease patient restraint straps 2. transfer patient. transfer of patient from a Secondary Device to ViC Chair Foow same procedure as in transferring from ViC chair to a secondary device above except: you must verify that the ViC chair is positioned so that the patients abdomen is in ine with the chair seat before attempting to transfer a patient to the ViC chair, otherwise tipping may occur. Figure

20 PREVENTIVE MAINTENANCE FOR THE USER 4 Component Ceaning Procedure Schedue Ceaning Agent * Specia Notes Pads/Mattresses Chair Eectrica components Mechanica chair components Mechanica accessories Wipe with damp coth to remove any foreign materia Wipe with damp coth to remove any foreign materia Wipe externa surfaces ONLY with damp coth to remove any foreign materia Wipe with damp coth to remove any foreign materia Wipe with damp coth to remove any foreign materia After each use After each use After each use After each use After each use Routine hospita grade disinfectants, soap and water Routine hospita grade disenfectants, soap and water Routine hospita grade disinfectants, soap and water Routine hospita grade disinfectants, soap and water Routine hospita grade disinfectants, soap and water Use ony medium strength ceaners Do not steam cean or pressure wash Lubricate pivot points after ceaning Use ony medium strength ceaners Lubricate pivot points after ceaning Lubricate pivot points after ceaning Procedure Schedue Materia Lubricate a moving and siding parts and hinge points Every 3 months Lubricating oi, ight-duty grease, wax stick ubricant or Never-Seez ubricant NEVER LUBRICATE GAS SPRING, MOTOR OR MECH-LOCK SHAFTS Inspect a fasteners to ensure proper fit, position and tightness (incuding nuts, bots, etc.) Inspect a surfaces and remove any sharp or burred areas; appy touch-up paint where required Every 3 months Every 3 months Proper size wrench and screwdriver Meta fie, proper coor paint (specify coor when ordering) * Disinfectants, viny products: Phenoic disinfectants are the best choice for viny products; propery diuted quaternaries are aso acceptabe. Quaternary/Isopropy disinfectants are not recommended for viny. Disinfectants, urethane products: Quaternary disinfectants are recommended for urethane products. Quaternary/ Isopropy disinfectants are recommended for urethane. Phenoics shoud be avoided on urethane. Disinfectants, a products: A fabrics may be ceaned with a 1:10 diution of househod beaches containing 5.25% sodium hypochorite as recommended by the Centers for Disease Contro in Atanta, Georgia. There is no harmfu effect on the fabric. Disinfectants appied at fu concentration or in highy concentrated soutions wi decrease the usefu ife of fabric. Iodophor type disinfectants used on fabrics may resut in staining. Sois or Stains: Use neutra soap suds and ukewarm water. Do not use harsh ceansers, sovents or detergents. Hard-To -Cean Spots: Use standard househod/viny ceansers and a soft briste brush on troubesome spots or stains. Pre-soak heavy, dried-on soi. Laundering Viny-aminated or Rubber-coated fabric is not recommended. Laundering may substantiay decrease the usefu ife of the fabric. Laundering Poyurethane-coated fabric: Machine wash with detergent up to 120 F. Some surface wrinking may occur; this wrinking has no adverse effect on the fabric properties. Hang or tumbe dry thoroughy at 140 F before storage. CAUTION - POSSIBLE EQUIPMENT DAMAGE HAZARD: Steam ceaning and pressure washing of chair is not recommended and can void warranty. NOTE: For more detaied information, pease contact GF Heath Products, Inc. at NOTE: In addition to the User Preventive Maintenance, a more detaied Preventive Maintenance Program is aso required to keep the equipment in good working order. This Preventive Maintenance Program is found on our website, at GFH RevB13

21 OptiOna accessories 6 number Description Sa pediatric positioner (36"x7") Sa pediatric positioner (48" x 10") Sa pediatric positioner (60" x 13") Sa0658 Foam wedge, patient positioning Sa Dorsocervica piow, Foam Sa X-wide restraint Straps with Vecro Sa universa Head restraint Sa0721 pushbar (removabe, Stainess Stee - Comes Standard) Sa ViC Back extension assemby ViC429 Ony (mfg after 4/98) Sa universa Head restraint with Dorsocervica teescoping i.v. rod, 27" to 50", 2-Section with Hoder (stainess) apc restraint Straps with Vecro, Comes Standard with 2 Straps apc patient tray apc14d-00 Oxygen tank Hoder arm Board with pad (for sitting) Sa4002 ViC Back extension Fied upgrade ViC429 Ony (mfg after 4/98) i t is recommended that ony accessories approved by GF Heath Products, Inc. be used with this device. t o order accessories, or for more detaied information on accessories, pease contact GF Heath Products, Inc. at

22 iustrated parts BreaKDOwn 6 Figure 6-1. ViC BaSe assemby Figure 6-1. ViC BaSe assemby 6-1

23 iustrated parts BreaKDOwn 6 Figure 6-1. ViC BaSe assemby item no. part no. S V C Description units per assemby ViC Base assemby X assemby, Base Frame ViC 2 p61117 * assemby, Outside Coumn SCrew, Hex Head Cap, 5/16-18 x 2" ong washer, 1/4 Sae Fat nut, ock 5/ nut, Free thread Hex, 5/ CaSter, Brake CaSter, Steer pate, Caster Bot ock SCrew, Hex Head Cap, M8 x 10" Cap, caster stem assemby, end Cover BOt, eye ink, Cam, Short ink, Connecting pin, ink pin, Cotter, 3/32 x 1/2" ong peda, Brake, Foot Cap, Starock SCrew, Set, 1/4-20 x 1/2" ong COar, Crank Shaft worm rod, Hex Brake, ong peda, pump, eft peda, pump, right SCrew, Button Head Socket, 1/4-20 x 1-1/4" ong nut, ock, 1/ pad, pump peda abe, pump peda, right abe, pump peda, eft BeOwS, apc BraCKet, Beows tie, Cabe abe, ViC Chair abe, Hausted product COVer, Center Base ange, Beows Mounting VeCrO, Hook 4" VeCrO, pie Cip, Beows 4 6-2

24 iustrated parts BreaKDOwn 6 Figure 6-1. ViC BaSe assemby item no. part no. S V C Description units per assemby rivet,.188 X.250 pop SCrew, #10 X 1/2 type a Sef tapping assemby, Seat pivot pate, nyatron guide assemby, Base pivot BuSHing, pivot washer, nyon, 5/ MeDiJaCK 1 48 p61121 * Hanger, Hydrauic Jack Support SuppOrt, Short gide SCrew, Coumn gide 4 51 p SCrew, 1/4-20 nyon tip SCrew, Coumn gide, w/o point assemby, inside Coumn abe, Operation abe, Seat ock washer, Fat, 5/16" HeaD, Steer peda washer, nyon, 1/2" washer, Shim, 5/16" grommet, rubber Cap, Steer peda, green Cap, Brake peda, red washer, Fat, 3/16" rivet, pop, 3/16" (arge Head) 2 note: the p prefix on the part numbers marked with an *, designate part numbers for the powder coated units. For chrome/stainess units the p prefix shoud be repaced with 0 prefix. 6-3

25 iustrated parts BreaKDOwn 6 Figure 6-2. Seat assemby Figure 6-2. Seat assemby 6-5

26 iustrated parts BreaKDOwn 6 Figure 6-2. Seat assemby item no. part no. S V C Description units per assemby assemby, Seat Section SCrew, Hex Head Cap, 5/16-18 x 3/4" ong assemby, Seat punger nut, ock, 5/ BOCK, pivot Support pate, gide Support pate, pivot Support washer, Fat, uss, 1/4" SCrew, Hex Head Cap, 5/16-18 x 1-3/4" ong abe, arrow, ViC washer, Fat, Sae, 1/4" washer, nyon, 3/4 OD x.395 id rod, rai pivot washer, removabe retaining rai, Side, ViC, eft rai, Side, ViC, right assemby, rai trigger pate Spring, rai punger punger tab, Viny, red pate, Stationery trigger, right pate, Stationery trigger, eft SCrew, truss Head Machine, #10-24 x 1.0" ong SpaCer, Seat pan C CuSHiOn, Seat, (Mauve) pate, Seat Cushion Support assemby, punger guide punger, Square Spring, punger KnOB, Back pu rod, punger abe, Seat ock pointer, Degree rivet, pop, 3/16 x.25" ong SCrew, phiips Head, #10-32 x 1-1/4" ong pad. arm rest 2 37 p Cap, Chrome Hoe 2 6-6

27 iustrated parts BreaKDOwn 6 Figure 6-3. FOOt SeCtiOn Figure 6-3. FOOt SeCtiOn 6-7

28 iustrated parts BreaKDOwn 6 Figure 6-3. FOOt SeCtiOn item no. part no. S V C Description units per assemby assemby, Foot Section SCrew, phiips Ova Head, 5/16-24 x 15/16 ong abe, Operating pin, Cevis, 3/8 x 1-7/16: ong nut, pa, 3/8" assemby, Foot rest pin, 1/8 x 3/4" ong assemby, ViC Foot end Contro SCrew, truss Head Machine, #10-24 x 3/8" ong pate, eg pad Support ring, retaining washer, Shim K CuSHiOn, eg Section, Mauve i CuSHiOn, Foot rest, Mauve Mat, For Foot rest abe, Foot rest warning abe, Service ring, retaining tag, Seria identification tag, Myar Cover For identification 1 21 not used abe, Head and Foot warning SpaCer, activating ever SCrew, truss Head Machine, #10-24 x 1.0" ong SCrew, Fat Socket Head, #10-24 x 5/8" ong nut, ock, # pin, ink, 5/16 x 1.0" ong pin, Cotter,.094 x 1/2" ong pin, eg extension tube COVer, eg Section ever, activating i Bearing, activating ever SHaFt, Contro Fange, nyiner, 62-FF assemby, Contro Box Bracket roer washer, Sae, 3/16" assemby, pu tube assemby, Sub, Contro pivot assemby, Cabe pu 1 6-8

29 iustrated parts BreaKDOwn 6 Figure 6-3. FOOt SeCtiOn item no. part no. S V C Description units per assemby ring, retaining, ring, retaining, SHaFt, Support pin, Spring, 1/8 x 5/8" tie, Cabe CaBe, eft punger CaBe, right punger CaBe, a.p.c, eg Contro washer, Sae Fat 1/4" OCK, Mechok Mechanica ring, retaining, tube, eg extension SCrew, Set, Knured,1/4-20 x 1/4" ong assemby, punger tube, eft assemby, punger rod ring, interna retaining 3/8" assemby, punger tube SCrew, Hex Head Cap, 5/16-18 x 1-1/2" ong nut, ock, 5/

30 iustrated parts BreaKDOwn 6 Figure 6-4. BaCK SeCtiOnS removabe push handes pace in wes on back of back section Kit part number Sa note: For Mode 429 ViC Chair, mount gas spring in this ocation. Figure 6-4. BaCK SeCtiOnS 6-11

31 iustrated parts BreaKDOwn 6 Figure 6-4. BaCK SeCtiOnS item no. part no. S V C Description units per assemby Back sections, Mode 329 X Back Sections, Mode 429 X assemby, Back Section SCrew, phiips Ova Head, 5/16-24 x 15/16" ong BOt, Shouder, 3/8 Dia. x 1.00" ong washer, nyon, 3/4 O.D. x.395 i.d nut, ock, 5/ pug, HOe, 1" Dia., S70-32 np abe, Head and Foot warning pie, Vecro, 2" x 12" pie, Vecro, 2" x 8" pan, narrow Back F pad, narrow Back, Mauve pan, ower Back Cap, Viny, 1/4 x rivet, pop SCrew, Fat Head Socket, 1/4-20 x 3/4" ong nut, acorn, 1/ pin, Cevis, 3/8 X 1-7/16" ong HanDe, reease, Vic Chair Cap, Viny, recine, green pin, gas Spring Hinge ring, retaining Spring, pneumatic CHaMBer, triger pin, actuator Cap, 3/8 pa assemby, Back Section, 14" pan, narrow Back, 14" w pad, narrow Back, 14", Mauve pan, ower Back, 14" abe, indicator grip, push Hande tube, push Hande CaBe, push Hande SCrew, truss Head Machine, #10-24 x 1.00" ong assemby, Mounting Bar nut, acorn, # * nut, Sef-Cinching, 1/ p75276 wedment, ViC Back extension

32 iustrated parts BreaKDOwn 6 Figure 6-4. BaCK SeCtiOnS item no. part no. S V C Description units per assemby pin, ocating pin, Spring, 3/16 x 1.00 g p75280 SHeet, ViC Back extension wedment, ower ock Channe nut, Joint Connector BOt, Joint Connector 1 45 p75292 pate, Hande Mounting wedment, extension activating Hande SCrew, truss Head Machine, #10-32 x 3/ nut, acorn, # tape, Hande gide tefon pie, Vecro, 2.00 x 5.00 (not Shown) rivet, pop, 3/16 (not Shown) abe, ViC Back instruction Cap, red Viny assemby, upper Channe nut, Joint Connector BOt, Joint Connector 2 *too # wi be required to insta nut, item

33 GF HEALTH PRODUCTS, INC. LIMITED WARRANTY 7 FOR HAUSTED BRAND PRODUCT LINE WITHIN THE U.S. SCOPE OF WARRANTY GF Heath Products, Inc. ( GF ) warrants to the origina purchaser ony that it wi repace or repair components, at GF s soe discretion, that are defective in materia or workmanship under norma use and service. A warranties are conditioned upon the proper use of the products stricty in accordance with good commercia practice and appicabe GF instructions and manuas, incuding proper use and maintenance. To the extent that a component is warranted by a third party, GF conveys a of its rights under that warranty to the origina purchaser, to the extent permitted. This imited warranty sha ony appy to defects that are reported to GF s customer service team within the appicabe warranty period and which, upon examination by GF or its authorized representative, prove to be a warranty item. This imited warranty is not transferabe. The warranted components and time period are set forth beow: COMPONENT....PARTS WARRANTY...LABOR WARRANTY Frame...5 years....5 years Hydrauics...1 year...1 year Casters...1 year...1 year Pneumatic gas springs...1 year...1 year Pads and mattresses....1 year...1 year Patient weighing system...1 year...1 year Eectrica components...1 year...1 year Optiona accessories....1 year...1 year Repacement parts *...90 days * The warranty period is as designated above. If a part is repaced under warranty, the origina warranty period wi not be affected. A other repacement parts wi be subject to the warranty period specified. The appicabe warranty period sha commence from date of shipment to the origina customer, uness there is an expiration date on the component in which case the warranty sha expire on the earier of warranty period or the expiration date. OBTAINING WARRANTY SERVICE A GF Customer Service Representative must authorize warranty service. Pease contact the GF Customer Service department by caing , sending a fax request to or by e-maiing a request to cs@grahamfied.com. Specific directions wi be provided by the Customer Service Representative. Faiure to abide by the specific directions wi resut in denia of the warranty caim. EXCLUSIONS The warranty does not cover and GF sha not be iabe for the foowing: 1) Defects, damage, or other conditions caused, in whoe or in part, by misuse, abuse, negigence, ateration, accident, freight damage, tampering or faiure to seek and obtain repair or repacement in a timey manner; 2) Products which are not instaed, used, or propery ceaned and maintained as required in the officia manua for the appicabe product; 3) Products considered to be of a consumabe nature incuding, but not imited to: fiters, fuses, gaskets, ubricants, and charts; 4) Accessories or parts not provided by GF; 5) Charges by anyone for adjustments, repairs, repacement parts, instaation or other work performed upon or in connection with such products which are not expressy authorized in writing, in advance, by GF; 6) Any shipping charges incurred in the repacement part instaation or repair; 7) Costs and expenses of reguar maintenance and ceaning; and 8) Representations and warranties made by any person or entity other than GF. ENTIRE WARRANTY, EXCLUSIVE REMEDY AND CONSEQUENTIAL DAMAGES DISCLAIMER THIS WARRANTY IS GF S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. GF MAKES NO IMPLIED WARRANTIES OF ANY KIND INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IF ANY MODEL OR SAMPLE WAS SHOWN TO THE CUSTOMER, SUCH MODEL OR SAMPLE WAS USED MERELY TO ILLUSTRATE THE GENERAL TYPE AND QUALITY OF THE PRODUCT AND NOT TO REPRESENT THAT THE PRODUCT WOULD NECESSARILY CONFORM TO THE MODEL OR SAMPLE IN ALL RESPECTS. THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PARTS. GF SHALL NOT BE LIABLE FOR AND HEREBY DISCLAIMS ANY DIRECT, SPECIAL, INDIRECT, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO: DAMAGES FOR LOSS OF PROFITS OR INCOME, LOSS OF USE, DOWNTIME, COVER, OR EMPLOYEE OR INDEPENDENT CONTRACTOR WAGES, PAYMENTS AND BENEFITS. The warranties contained herein contain a the representations and warranties with respect to the subject matter of this document, and supersede a prior negotiations, agreements and understandings with respect thereto. The recipient of this document hereby acknowedges and represents that it has not reied on any representation, assertion, guarantee, warranty, coatera contract or other assurance, except those set out in this document. For additiona information on this Hausted product or this warranty, pease contact a GF Customer Service Representative. NOTES: 1) Additiona terms and conditions may appy. 2) Freight caims must be notated on the Bi of Lading and must be made with immediacy. The ICC reguations govern specific requirements for freight caims. Faiure to abide by those reguations may resut in a denia of the freight caim. GF wi assist you in fiing the freight caim. 3) Caims for any short shipment must be made within thirty (30) days of the invoice date GFH RevB13

34