PUSH BUTTON KEY CABINET

Transcription

1 PUSH BUTTON KEY CABINET Model INSTALLATION And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein Mission Oaks Blvd., Camarillo, CA Visit our website at: To prevent serious injury, read and understand all warnings and instructions before use. Copyright 2007 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call

2 Specifications Overall Dimension 3-3/4 L x 7-15/16 W x 11-3/4 H Materials Stamped Sheet Steel, Brass, Thermoplastic Finish Enamel Paint, Zinc Plated, Black Plastic, Steel Finish Open Door Type Round Long Pin- Pin Size 10-3/4 x.151 Diameter Mounting Hole Size (2).580 L x.189 W x.390 Diameter-Mounting Screw Included (2) Key Slots 20 (2 welded brackets, 10 per bracket) Net Weight 4.3 Lbs. Save This Manual You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Write the product s serial number in the back of the manual near the assembly diagram, or write month and year of purchase if product has no number. Keep this manual and invoice in a safe and dry place for future reference. GENERAL SAFETY RULES WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit. Cluttered areas invite accidents. For security reasons, keep bystanders, children, and visitors away from this product. Personal Safety Dress properly. Do not wear loose clothing or jewelry when securing this product to the wall. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Check for damaged parts. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect this product. Page 2

3 3. 4. Use safety equipment. Always wear eye protection. Always wear ANSI-approved safety goggles when assembling this product. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code , et seq.) Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. MOUNTING INSTRUCTIONS Bracket w/key Slots Mounting Holes Figure Use the two mounting holes on the back of the Key Cabinet as a template. Position the Key Cabinet against the wall. Use a pencil to mark the mounting holes. Set the Key Cabinet aside. Note: It is best to locate a wooden stud behind the wall for mounting or use Drywall Anchors (not included) when installing into drywall. See Figure In the wall, drill holes (0.144 dia.) where previously marked with the pencil. Caution: Before drilling holes, check for hidden electrical wires, pipes or cords in the drilling path. Line up the mounting holes on the back of the Key Cabinet with the holes drilled into the wall. Use correct hardware (not included) and tighten the screws that will hold the Key Cabinet securely in place. Page 3

4 Note: Hook the keys along the inside of the cabinet on the brackets. See Figure setting YOUR CODE There should be no preset code for the key box when it arrives. The door should be closed but not locked when the factory ships it. To open the door just turn the Handle. If the key box arrives locked or if you lock it by accident, slide the clear button down and then turn the knob to open the door. Follow the step below under changing the code, to set your own personal code. See Figure 2 changing THE CODE Turn Handle Pad (4) Clear Button Figure 2 Decide on your new personal code. You may only use each number once. Use a 3 to 8 digit number. It is important that you remember this number. Write it down in a safe place that can be found if you forget the number. NOTE: It does not matter which order you punch in your numbers. For instance if your code is 1-2-3, you can input your code as or and the lock will still open. Page 4

5 2. To change the code, push the Clear Button. It should click. Turn the Turn Handle Small Knob Holding the Plastic Plate Plastic Plate on the Back of the Key Pad (4) Figure 3 and it should open. Use a flat-head screwdriver (not provided) to unscrew the small knob that holds the numbered plate on the back of the Key Pad (4). Remove and set aside. See Figure 3. Page 5

6 Small Triangle pointing up or down. Numbered Slotted Disk for Changing Key Pad Combination Figure When the plate is removed, there are ten slotted disks with triangles pointing upward. These slotted disks are numbered and represent each of the ten available digits. With the screwdriver, gently turn the slotted disk that represents the first number in your code. Turn it 180o. The triangle now points downward. Repeat this step for each of the numbers in your code. See Figures 4 & 5. Slotted Disk Number not working. s s Number working. Figure Replace the plastic plate and secure it with the Knob. Tighten with the screw driver. Once you have input your code, you should check that it has been correctly set. Keep the Key Cabinet door OPEN. DO NOT close the door or replace the plastic plate until you are sure your code works. It is recommended you try it at least three times. Page 6

7 8. Press your new code. Press the Top Open Button. Turn the Handle. Door should click and open. See Figure 6. Note: If any of the numbered buttons fail to depress after you have set your code, then check that they have been turned a fully 180o. Repeat the previous steps. Turn Handle Top Open Button Pad (4) Figure 6 2. INSPECTION, MAINTENANCE, AND CLEANING BEFORE EACH USE, inspect the general condition of this product. Check for loose mounting screws and any other condition that may affect its safe operation. Do not use damaged equipment. Wipe down with a damp cloth to remove dust or soil. Air dry before replacing keys and closing the door. Page 7

8 PARTS LIST Part # Description Qty. 1 Key Cabinet 1 2 Key Hooks 20 3 Turn Handle 1 4 Key Pad 1 Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Bracket w/key Hooks (2) 1 3 Mounting Holes 4 PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto. Page 8

9 WARRANTY Limited 90 day warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state Mission Oaks Blvd. PO Box 6009 Camarillo, CA (800) Record Product s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Page 9