Morris Products 53 Carey Road, Queensbury, NY 12804

Transcription

1 Catalog Number 790 UPC Number Description Low Profile Emergency Lighting allast 500 Lumen T5 & T8 Fixtures Features For both normal and emergency Flourescent lighting. In the event of a Power Failure, the allast Switches to the Emergency Mode and operates one or two of the existing lamps for a minimum of 90 minutes. Low Profile (Rated for T5 & T8 allasts - includes a Time Delay function) Time Delay Feature for end of life circuitry to prevent C allast from shutting down when transitioning from Emergency to C Open circuit insulation feature to protect unit when load is absent Contains a Ni-Cad attery, Charger, and Inverter Circuit in a single package. Can be mounted in the wireway or on top of the fixture. 90 minute minimum emergency power, 4 hour recharge time Temperature Range: 0 o C to 50 o C 0/77 Volt 60 Hz UL listed for factory installation or retrofit applications UL Listed Damp Location Standard allasts Low Profile ballasts are rated for use with: D30T5 & T8 single or bi-pin or lamp 8-50W 4-Pin Long Compact 3W 4-Pin Compact 4-3W U-end FT8 lamps from Phillips, GE & Osram or equal Compatible with most one, two, three & four lamp electronic standard energy saving & dimming C ballasts Compatible with Instant Start & Rapid Start allasts. General Housing: Finish: Lamp Type: attery : Emergency Power: Galvanized Steel Powder Coat or Lamp, ' - 8' T5, T8 Ni-Cad 90 minutes Dimension Information Length: 9.0" Heigth:.0" Depth:.0" Specifications Temperature Rating 0 o C to 50 o C Voltage Rating 0/77 V Frequency: 60 Hz Flammability Rating N/ Input Wattage:.5 Wattage Rating 8 Watt Per Lamp attery: Ni-Cad 6V Packaging ox Qty Certifications UL UL 94 cul Yes RoHS Yes Morris Products 53 Carey Road, Queensbury, NY 804

2 .00" INSTLLTION INSTRUCTIONS 650 Lumens pin When using this lighting device the safety precautions should be followed at all time PLESE CREFULLY ND FOLLOW LL INSTRUCTIONS F YOUR OWN SFETY. This device is designed for indoor use. Do not use outdoors.. Prior to installation, battery connector must be open to prevent high voltage from being present on out put leads (red & yellow). 3. This device is designed for use with One double twin-tube (quad) or one triple twin-tube compact fluorescent lamp shown in the Lamp Rating Chart as Follow. Lamp Rating Chart (Operates lamp) Wattage 0, 3, 8, 6 ase G4d Wattage 3, 8, 6 ase GX4d 4. Please ensure the electricity connections conforms to the National Electrical Code and local regulations if applicable. 5. To avoid electric shock, please disconnect normal and emergency power supplies, and battery connector of the emergency ballast before servicing. 6. This device is designed for factory or field installation in either the ballast channel, or on top of the indoor fixture, except air handling heated air outlets, wet, or hazardous location fixtures. Do not install this device near gas or electric heaters. 7. C power source of 0VC or 77VC is required. 8. The battery is sealed, non-maintenance, and is not replaceable in the field. Please contact manufacturer for information on service. Do not attempt to service the battery please. 9. Do not use accessory equipment that is not recommended by manufacturer. Failure to do so may cause unsafe conditions. Servicing should only be performed by qualified service personnel. 0. Do not use the product for other purpose that the product is NOT designed for. PLESE SVE THESE INSTRUCTIONS

3 INSTLL INSTRUCTION NOTE: ll the branch circuit wiring has to be ready as well as an unswitched source of power before the fixture is installed. Confirmed the same branch circuit would the emergency ballast as C ballast. CUTION: Inverter connector has to be opened for preventing high voltage on output leads (Red and Yellow). Wait until all the installation process is completed and C is supplying power to the emergency ballast then join the inverter connector.. Disconnect C power from the fixture.. Choose the right wiring diagram to connect the emergency ballast to C ballast and lamp. 3. Follow diagram to connect the emergency ballast and test plate. Please ensure the electricity connections conform to the National Electrical Code and local regulations if applicable. Install the test plate close to the fixture or at a remote location within 50feet is recommended. The emergency ballast install up to half distance the C ballast manufacturer recommends install the C ballast from the lamp or install within 50feet is recommended. Please choose the one in less distance. The emergency ballast could be mounted within 50feet if there isn't C ballast. 4. Cut the wire between the lamp holder and C ballast and then connect the blue and blue/white wire from emergency ballast to C ballast and the yellow and yellow/black wires to the lamp holder. 5. The emergency ballast has to be connecting to an unswitched 0VC or 77VC power source with no exception. Other voltages are not accepted!! Do not join the inverter connector until the fixture is completely installed and supply C power to the emergency ballast. 6.n additional unswitched hot wire (0VC or 77VC) has to be run to the junction box and connected to the emergency ballast if there is in ON ED FIXTURES. 7. efore having a long-term emergency function testing, the battery in emergency ballast has to be charged for 4 hours. 8.Please search in readily visible location and stick the label with "CUTION: This Unit Has More Than One Power Supply Connection Point. To Reduce The Risk Of Electric Shock, Disconnect oth The ranch Circuit-reakers Or Fuses nd Emergency Power Supplies efore Servicing." 9. See Diagram and 3 showing basic switched and unswitched fixture connections. See back page for more detailed wiring schematics. The emergency ballastcan be used with one- or twom-lamp fixtures, however, it omly operates one lamp in the emergency mode. NOTE: OX IS NOT SUPPLIED OPERTION: THE CHRGING INDICT WOULD E ON TO INDICTE THE TTERY IS EING CHRGED WHEN C POWER IS PPLIED WHEN POWER FILS THE DEVICE OF THIS LLST WILL OPERTE LMPS T LEST 90MINUTES.

4 DIGRM TO LMP FIXTURE 3 JUNCTION OX C LINE IN TO LMP FIXTURE 3 JUNCTION OX C LINE IN LLST 4 4 WLL LLST Emergency ballast Shading - Equipment supplied by others WLL PLTE PLTE NOTE: The test/monitor plate can be remotely installed up to 50 feet from the emergency ballast. The emergency ballast may be remotely mounted up to half the distance recommended by the C ballast manufacturer. If no C ballast is used, the emergency ballast can be remotely mounted up to 50 feet away. 3 4 Flexible conduit (supplied) to connect ballast wire. Existing conduit to run existing wire to lamp holder (C ballast on junction box). If C ballast is on reflector, run yellow, and blue wires from emergency ballast through this conduit. C line in. Conduit and junction box (not supplied), necessary for remote installation. MINTENNCE: NOTE: SERVICES SHOULD ONLY PERFMED Y QULIFIED PERSONNEL. THE LLST SHOULD E CHECKED PERIODICLLY TO CONFIRM FUNCTIONING ND THE FOLLOWING SCHEDULE IS RECOMMENDED. ) TO INSPECT THE CHRGING INDICT EVERY MONTH ND CONFIRM THT IS ILLUMINTED. ) PUSH THE F 30 SECONDS TO ENSURE THE LLST IS FUNCTIONING. RECOMMENDED TO PERFM THIS ING IN EVERY 30 DYS. 3) PERFMING LONG-TERM (90 MINUTE TTERY DISCHRGE) IN EVERY YER. THE LMPS SHOULD E OPERTED F NO LESS THN 90 MINUTES. SWITHED HOT 0V 77V WLL C allast LMP ED FIXTURE JUNCTION OX LCK 0V NGE 77V (CP LED) CP LED DIGRM DIGRM 3 FLEX LLST FLEX VIOLET + ROWN - PLTE INDICT UNED FIXTURE JUNCTION OX 0V 77V LCK 0V NGE 77V (CP LED) C allast LMP CP LED FLEX LLST FLEX VIOLET + ROWN - PLTE INDICT For 0V, connect unswitched hot to black emergency ballast lead and cap unused orange wire. For 77V, connect unswitched hot to orange emergency ballast lead and cap unused black wire. WIRE DIGRMS F -LMP OPERTION LLST ND C LLST MUST E FED FROM THE SME RNCH CIRCUIT TYPICL SCHEMTICS ONLY. MY E USED WITH OTHER LLSTS. CONSULT THE FCTY F OTHER WIRING DIGRMS.. TWO-LMP FIXTURE, TWO SIMPLE RECT C LLSTS (Lamp operates in emergency mode).) FLEX Conduit Wiring Diagram:.) FLEX Conduit Wiring Diagram: LCK 0V NGE 77V (CP LED) C allast (ED UNED) C allast LMP LMP LLST ROWN- INDICT

5 WIRE DIGRMS F -LMP OPERTION LLST ND C LLST MUST E FED FROM THE SME RNCH CIRCUIT TYPICL SCHEMTICS ONLY. MY E USED WITH OTHER LLSTS. CONSULT THE FCTY F OTHER WIRING DIGRMS.. TWO-LMP FIXTURE, TWO UTOTRNSFMER C LLSTS (Lamp operates in emergency mode).) FLEX Conduit Wiring Diagram:.) FLEX Conduit Wiring Diagram: (ED UNED) LMP LMP C allast C allast LCK 0V NGE 77V (CP LED) LU WHT WHT LU LU LLST ROWN- INDICT C. ONE-LMP FIXTURE, ONE SIMPLE RECT C LLST.) FLEX Conduit Wiring Diagram:.) FLEX Conduit Wiring Diagram: LMP (ED UNED) C allast CP LED LCK 0V NGE 77V (CP LED) LLST ROWN- INDICT D. ONE-LMP FIXTURE, ONE UTOTRNSFMER C LLST.) FLEX Conduit Wiring Diagram:.) FLEX Conduit Wiring Diagram: LCK 0V NGE 77V (CP LED) LU LU C allast (ED UNED) WHT LMP LLST ROWN- INDICT E. ONE-LMP FIXTURE WITHOUT C LLST.) FLEX Conduit Wiring Diagram:.) FLEX Conduit Wiring Diagram: LMP CP LED CP LED LCK 0V NGE 77V (CP LED) LLST ROWN- INDICT F. TWO-LMP FIXTURE, TWO LMP OLIER POWER SPEC ELECTRONIC C LLST (Lamp operates in emergency mode).) FLEX Conduit Wiring Diagram:.) FLEX Conduit Wiring Diagram: LCK 0V NGE 77V (CP LED) (ED UNED) OLIER (Line) LMP WHT POWER SPEC WHT WHT/ WHT ELECTRONIC (Neutral) C LLST LMP LLST ROWN- INDICT

6 L650C- Return sample re-test wiring diagram.) FLEX Conduit Wiring Diagram:.) FLEX Conduit Wiring Diagram: LCK 0V NGE 77V (CP LED) Instant C allast (ED UNED) Instant C allast LMP(T8 5W) LMP (Pin-W) LLST ROWN- INDICT L650C- Production on-line test wiring diagram.) FLEX Conduit Wiring Diagram:.) FLEX Conduit Wiring Diagram: LCK 0V NGE 77V (CP LED) Instant C allast (ED UNED) Instant C allast LMP(T8 5W) LMP(T8 5W) LLST ROWN- INDICT