TL1 OL-AL(MDB)-TL1-EN. Alarms & Remote Start

Transcription

1 Alarms & Remote Start Omega R&D Inc. ISTALL UIDE OL-AL(MDB-TL-E TL Available for : OL-MDB-ALL Rev. Date: June 0, 0 The brand names and logos found in this guide are property of their respective owners. Omega R&D Inc. 0! OTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation uide carefully before beginning any work.

2 Page of install TYPE SELECTiOn FEURES BRAKE PEDAL STUS OUTPUT E-BRAKE OUTPUT DOOR STUS OUTPUT TRUK STUS OUTPUT HOOD STUS OUTPUT* TOYOTA Camry (0-bit 0- Camry 0- Camry Hybrid 0- Corolla (0-bit 09-0 Corolla 09- Corolla MT 09- Highlander (0-bit 08-0 Highlander 08- Highlander Hybrid 08- Matrix (0-bit 09-0 Rav (0-bit 0-0 Rav 09- Sequoia (0-bit 08-0 Tundra (0-bit Yaris (0-bit * Available only if vehicle is equipped with factory hood switch. ISTALL TYPE TRUK/HCH RELEASE xd (0-bit DOOR ULOCK xb (0-bit DOOR LOCK DA IMMOBILIZER BYPASS 09-0 DISARM OEM ALARM YEAR Vibe ARM OEM ALARM MODEL PUSH TO START CTRL MAKE 0- SCIO POTIAC ES0 TAILE WIDOW RELEASE Keyless and smartkey systems will remain functional during remote start. LEXUS I TACHOMETER OUTPUT OTE

3 Page of COMPOnEnT LOCOr A B C

4 Page of AME TYPE POSITIO POLARITY MODULE LOCIO COMPOET LOCOR 0 Red 0 Brown E Beige 0 LtBlue E8 0 0 reen 0 Pink 09-0 E8 Corolla TMMC 09-0 Corolla UMMI TOYOTA Highlander Matrix Rav Sequoia Tundra Yaris DESCRIPTIO Camry YEAR MODEL MAKE TYPE - wire CrOSS reference CHArT - OF 0 0 LtBlue 0 Red D 8 LtBlue 0 Blue Beige 0 LtBlue E reen 0 Pink E Blue 0 H 8 Orange Purple 0 Blue 0 J0 8 Ltray Purple 0 Purple 0 reen Purple

5 Page of SCIO xb xd AME TYPE POSITIO POLARITY MODULE LOCIO COMPOET LOCOR YEAR MODEL Vibe DESCRIPTIO POTIAC MAKE TYPE - wire CrOSS reference CHArT - OF Beige LtBlue E 09-0 Beige LtBlue C Purple reen 08-0 Purple

6 Page of TYPE - wiring DIARAM OTE AD PIOUT MAY VARY. PLEASE REFER TO CHART. PARKI LIHT SWITCH PA RK I LI HT ( REMOTE STARTER PARKI LIHT OUTPUT TACH (AC IPUT E-BRAKE STUS IPUT TRUK/TAILE WIDOW RELEASE OUTPUT ULOCK/DISARM OUTPUT LOCK/ARM OUTPUT V ROUD ROUD WHE RUI OUTPUT DE CO CT TX STADARD (I, ACC, START REMOTE STARTER COECTIOS TO VEHICLE ARE REQUIRED IITIO IPUT/OUTPUT BRAKE IPUT HOOD STUS IPUT TRUK STUS IPUT DOOR STUS IPUT DA MODE /A LEED OT REQUIRED I DA MODE (-WAY OT REQUIRED I DA MODE (-WAY USE DA MODE OR HARD MODE YELLOW/BLACK - DOOR STUS OUTPUT YELLOW/RED - TRUK STUS OUTPUT YELLOW - HOOD STUS OUTPUT BROW/RED - H BROW/YELLOW - L ORAE/BLACK - ROUD IPUT ORAE/WHITE (C ORAE - BRAKE OUTPUT PIK/BLACK (C PIK - IITIO IPUT BLUE/RED (C BLUE/YELLOW (C REE/RED - CODE REE/YELLOW (C RAY/RED - RAY/YELLOW (C WITHOUT OEM HOOD SWITCH OLY L LOCK/ARM IPUT - REE/BLACK ULOCK/DISARM IPUT - BLUE/BLACK TRUK/TAILE WIDOW RELEASE IPUT - RED/WHITE (C BROW (C PURPLE/YELLOW (C PURPLE/BLACK (C WHITE (C BLACK/WHITE E-BRAKE STUS OUTPUT - REE TACH (AC OUTPUT - PURPLE/WHITE WHITE/BLACK (C WHITE/RED (C WHITE (C H WR IPUT - BLUE/WHITE (C WHITE ROUD - BLACK V - RED DA MODE 8 9 0

7 Page of Rav 09- TYPE POSITIO POLARITY MODULE LOCIO COMPOET LOCOR 09- AME Corolla UMMI 09- DESCRIPTIO TOYOTA Corolla TMMC YEAR MODEL MAKE TYPE - wire CrOSS reference CHArT - OF F 8 pin Yellow E 9 pin pin E8 F 8 pin Red E 9 pin pin E8 F 8 pin Yellow E 9 pin Red pin E

8 Page 8 of TYPE - wiring DIARAM MAI BODY FROT SIDE BACK SIDE OTE AD PIOUT MAY VARY. PLEASE REFER TO CHART PA RK I LI HT ( PARKI LIHT SWITCH WARI: DO OT COECT AY OTHER ACCESSORY,IITIO OR START FROM THE REMOTE STARTER TO THE VEHICLE. THE ITERFACE MODULE IS HADLI THE REQUIRED VEHICLE POWER AD START SEQUECE FROM THE PUSH TO START BUTTO CIRCUIT. O ( H L LOCK/ARM IPUT - REE/BLACK ULOCK/DISARM IPUT - BLUE/BLACK TRUK IPUT - RED/WHITE (C BROW (C PURPLE/YELLOW (C PURPLE/BLACK (C WHITE STARTER IPUT - BLACK/WHITE E-BRAKE STUS OUTPUT - REE TACH (AC OUTPUT - PURPLE/WHITE DA MODE 00 USE DA MODE OR HARD MODE WR IPUT - BLUE/WHITE (C WHITE ROUD - BLACK V - RED DIODE IITIO IPUT BRAKE IPUT HOOD STUS IPUT TRUK STUS IPUT DOOR STUS IPUT (+ SW ST LEED OT REQUIRED I DA MODE (-WAY OT REQUIRED I DA MODE (-WAY TI I <- OPTIOAL DA MODE /A I PARKI LIHT OUTPUT TACH (AC IPUT E-BRAKE STUS IPUT STARTER OUTPUT TRUK OUTPUT ULOCK/DISARM OUTPUT LOCK/ARM OUTPUT V ROUD ROUD WHE RUI OUTPUT REMOTE STARTER WHITE/BLACK - OUTPUT WHITE/RED (C WHITE - IITIO IPUT YELLOW/BLACK - DOOR STUS OUTPUT YELLOW/RED - TRUK STUS OUTPUT YELLOW - HOOD STUS OUTPUT BROW/RED - H BROW/YELLOW - L ORAE/BLACK - ROUD IPUT ORAE/WHITE (C ORAE - BRAKE OUTPUT PIK/BLACK (C PIK - IITIO IPUT WITHOUT OEM HOOD SWITCH OLY BLUE/RED - ROUD IPUT BLUE/YELLOW - OUTPUT REE/RED (C REE/YELLOW (C RAY/RED (C RAY/YELLOW (C IMPORTAT: - O TAKEOVER AVAILABLE. UPO OPEI VEHICLE DOOR EIE WILL SHUTDOW. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. EIE START STOP PT S (- COECTIOS ARE REQUIRED OLY IF IDLE MODE IS DESIRED

9 Page 9 of 0- Highlander Highlander Hybrid TYPE POSITIO POLARITY MODULE LOCIO COMPOET LOCOR 0- TOYOTA Camry Hybrid 0- AME Camry YEAR MODEL ES0 DESCRIPTIO LEXUS MAKE TYPE - wire CrOSS reference CHArT - OF I 0 pin 0 E 0 pin 0 Red pin 0 Blue E 8 0 Pink I 0 pin 0 Brown E9 0 pin 0 ray pin 0 Blue E 8 0 I 0 pin 0 Brown E9 0 pin 0 ray pin 0 Blue E 8 0 I 0 pin 0 D0 0 pin 0 Pink pin 0 Pink D 8 LtBlue 0 Blue I 0 pin 0 D0 0 pin 0 Yellow pin 0 Pink D 8 LtBlue 0

10 Page 0 of TYPE - wiring DIARAM MAI BODY BACK SIDE OTE AD PIOUT MAY VARY. PLEASE REFER TO CHART REMOTE STARTER O TI I I I PA RK (+ WARI: DO OT COECT AY OTHER ACCESSORY,IITIO OR START FROM THE REMOTE STARTER TO THE VEHICLE. THE ITERFACE MODULE IS HADLI THE REQUIRED VEHICLE POWER AD START SEQUECE FROM THE PUSH TO START BUTTO CIRCUIT. (+ SW LI ST HT ( PARKI LIHT SWITCH PARKI LIHT OUTPUT TACH (AC IPUT E-BRAKE STUS IPUT STARTER OUTPUT TRUK/TAILE WIDOW RELEASE OUTPUT ULOCK/DISARM OUTPUT LOCK/ARM OUTPUT V ROUD ROUD WHE RUI OUTPUT DA MODE /A LEED OT REQUIRED I DA MODE (-WAY OT REQUIRED I DA MODE (-WAY <- OPTIOAL DIODE IITIO IPUT BRAKE IPUT HOOD STUS IPUT TRUK STUS IPUT DOOR STUS IPUT H L USE DA MODE OR HARD MODE DA MODE WR IPUT - BLUE/WHITE (C WHITE ROUD - BLACK V - RED LOCK/ARM IPUT - REE/BLACK ULOCK/DISARM IPUT - BLUE/BLACK TRUK/TAILE WID. RELEASE IPUT - RED/WHITE (C BROW (C PURPLE/YELLOW (C PURPLE/BLACK (C WHITE STARTER IPUT - BLACK/WHITE E-BRAKE STUS OUTPUT - REE TACH (AC OUTPUT - PURPLE/WHITE WHITE/BLACK - OUTPUT WHITE/RED (C WHITE - IITIO IPUT YELLOW/BLACK - DOOR STUS OUTPUT YELLOW/RED - TRUK STUS OUTPUT YELLOW - HOOD STUS OUTPUT BROW/RED - H BROW/YELLOW - L ORAE/BLACK - ROUD IPUT ORAE/WHITE (C ORAE - BRAKE OUTPUT PIK/BLACK (C PIK - IITIO IPUT WITHOUT OEM HOOD SWITCH OLY BLUE/RED - ROUD IPUT BLUE/YELLOW - OUTPUT REE/RED (C REE/YELLOW (C RAY/RED (C RAY/YELLOW (C IMPORTAT: - O TAKEOVER AVAILABLE. UPO OPEI VEHICLE DOOR EIE WILL SHUTDOW. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. EIE START STOP PT S (- COECTIOS ARE REQUIRED OLY IF IDLE MODE IS DESIRED

11 Page of TYPE POSITIO POLARITY MODULE LOCIO COMPOET LOCOR 09- AME Corolla UMMI MT DESCRIPTIO 09- TOYOTA Corolla TMMC MT YEAR MODEL MAKE TYPE - wire CrOSS reference CHArT - OF F 8 pin Yellow A E 9 pin A E8 pin B E8 Clutch A pin Clutch Switch C Clutch A pin Clutch Switch C F 8 pin Red A E 9 pin A E8 pin B E8 Clutch A pin Clutch Switch C Clutch A pin Clutch Switch C

12 Page of TYPE - wiring DIARAM MAI BODY FROT SIDE BACK SIDE OTE AD PIOUT MAY VARY. PLEASE REFER TO CHART PA RK I LI HT ( PARKI LIHT SWITCH WARI: DO OT COECT AY OTHER ACCESSORY,IITIO OR START FROM THE REMOTE STARTER TO THE VEHICLE. THE ITERFACE MODULE IS HADLI THE REQUIRED VEHICLE POWER AD START SEQUECE FROM THE PUSH TO START BUTTO CIRCUIT. O ( H L A - CLUTCH SWITCH 8 8A 8 WHITE/BLACK - OUTPUT WHITE/RED (C WHITE - IITIO IPUT YELLOW/BLACK - DOOR STUS OUTPUT YELLOW/RED - TRUK STUS OUTPUT YELLOW - HOOD STUS OUTPUT BROW/RED - H BROW/YELLOW - L ORAE/BLACK - ROUD IPUT ORAE/WHITE (C ORAE - BRAKE OUTPUT PIK/BLACK (C PIK - IITIO IPUT WITHOUT OEM HOOD SWITCH OLY BLUE/RED - ROUD IPUT BLUE/YELLOW - OUTPUT REE/RED (C REE/YELLOW (C RAY/RED - ROUD IPUT RAY/YELLOW (C 0 IMPORTAT: - O TAKEOVER AVAILABLE. UPO OPEI VEHICLE DOOR EIE WILL SHUTDOW. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. EIE START STOP PT S (- CL CH UT CH UT CL 8 LOCK/ARM IPUT - REE/BLACK ULOCK/DISARM IPUT - BLUE/BLACK TRUK IPUT - RED/WHITE (C BROW (C PURPLE/YELLOW (C PURPLE/BLACK (C WHITE STARTER IPUT - BLACK/WHITE E-BRAKE STUS OUTPUT - REE TACH (AC OUTPUT - PURPLE/WHITE V DA MODE WR IPUT - BLUE/WHITE (C WHITE ROUD - BLACK V - RED 00 USE DA MODE OR HARD MODE DIODE IITIO IPUT BRAKE IPUT HOOD STUS IPUT TRUK STUS IPUT DOOR STUS IPUT (+ SW ST LEED OT REQUIRED I DA MODE (-WAY OT REQUIRED I DA MODE (-WAY TI I <- OPTIOAL DA MODE /A I PARKI LIHT OUTPUT TACH (AC IPUT E-BRAKE STUS IPUT STARTER OUTPUT TRUK OUTPUT ULOCK/DISARM OUTPUT LOCK/ARM OUTPUT V ROUD ROUD WHE RUI OUTPUT REMOTE STARTER

13 Page of installion MODE SELECTiOn Press and release programming button to select installation mode. LED flashes (X once = DA MODE LED flashes (X twice = STADARD HARD MODE! Press and hold programming button until LED turns solid REE to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. TYPE - MODULE PrOgrAMMing PrOCEDUrE OTE I Insert key into ignition. LED will flash REE and RED. 8 Wait, LED will turn solid REE then will turn OFF. Turn key to OFF position. 9 Remove key. Remove key. 0 Module Programming Procedure completed. Between each step, LED will turn solid RED, this is the default standby mode. Insert key into ignition. Turn key to O position. O x OFF (If vehicle is not equipped with immobilizer, press module programming button. LED will flash REE once [x].

14 Page of TYPE, & - MODULE PrOgrAMMing PrOCEDUrE OTE I Between each step, LED will turn solid RED, this is the default standby mode. Æ EIE START STOP x Push start button twice [x] to O position. Æ EIE START STOP x Push start button once [x] to OFF position. Module Programming Procedure completed. Wait, LED will turn solid REE then will turn OFF.

15 CLASSIC XX-XX PET - PAE X-X Page of identify VEHiCLE notice YEAr Locate the Vehicle Identification umber (VI and identify the 0th character. Æ AYTAL8DR0X Match the VI s 0th character to its corresponding year. L > 990 S > 99 Y > 000 > 00 A > 00 M > 99 T > 99 > 00 > 00 B > 0 > 99 V > 99 > 00 > 00 C > 0 P > 99 W > 998 > 00 8 > 008 D > 0 R > 99 X > 999 > 00 9 > 009 E > 0 MODULE DiAgnOSTiCS LED STUS DIAOSTICS DURI PRORAMMI DURI REMOTE START WITH IITIO OFF Flashing RED Missing/wrong information from firmware or vehicle Incorrectly programmed Incorrectly programmed or connected Solid RED Waiting for more vehicle information Incorrectly programmed ot programmed waiting for more vehicle information Flashing REE Additional steps required to complete programming Correctly programmed and operational False ground when running status from remote starter Solid REE then OFF Correctly programmed Reset in progress Reset in progress OFF o activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence LED will turn solid red for seconds. RESET COMPLETED. RECOECT all connectors. DISCOECT black -PI standard or optional data connector. DISCOECT all connectors from module EXCEPT the black -PI standard or optional data connector. FACTOrY reset PrOCEDUrE PRESS AD HOLD programming button while connecting either -PI standard or optional data connector. Repeat programming procedure.! Failure to follow procedure may result with a DTC or a CHECK EIE error message. When LED flashes red, RELEASE programming button. This product is protected by one or more of the following patents: U.S. LETTErS PEnT no.,9,;,0,0;,,00;,9,;,,;,9,;,,8;,9,;,9,;,9,9;,,88;,,88;,,;,8,89;,9,0;,00,0;,0,8;,0,;,0,;,08,;,0,80;,0,9;,,08;,9,9;,8,9;,89,;,0,9; nadian PEnT no.,0,8;,,0;,,0;,,99;,,0;,,0;,,08;,,0;,0,89;,,90;,,9;,,8; EUrOPEAn PEnT no.,0,8; DE 980-9T; U.S. 000; 00098; 00098; 00008; ; ; EP00; 808; 80;