Automotive Data Solutions Inc. Rev. Date: December 06, 2012 Doc. No.: ##10232##

Transcription

1 Automotive Data Solutions Inc. INSTALL GUIDE DBI-AL(DL)-VW1-EN Available for : DBI-AL CA Rev. Date: December 06, 2012 Doc. No.: ##10232## VW1 Version FRançaise disponible en ligne au please visit for complete product details The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.

2 Page 2 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## install TYPE SELECTiOn features Make MoDel NOTE I Direct-Shift Gearbox (DSG): Connect starter wire to starter solenoid in engine bay. See RS manufacturer for wire information. Year InStall type PrIorItY Unlock Door lock Door Unlock arm oem alarm DISarM oem alarm trunk/hatch release Door Stat output HooD Stat output trunk Stat output Brake PeDal Stat output e-brake output tachometer output A A3 5 A4 Convertible/Sedan A6/A6 Allroad Quattro Q S S3 5 S4 Convertible/Sedan S TT Beetle 4 New Beetle Coupe/Convertible * CC City Golf ** * City Jetta ** * Eos Eos 5 Golf * Golf 3-door/5-door/Wagon Golf 3-door/5-door/Wagon 5 GLI GTI * GTI GTI 5 Jetta * Jetta Jetta (2 plug BCM) Jetta (3 plug BCM) Passat * Passat/Passat CC Passat 5 Rabbit Tiguan Tiguan 5 * -AL Module will be functional on these vehicles only if they are equipped with electric windows. ** With electric windows & sunroof. audi VolkS WaGen

3 Page 3 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## TYPE 1 - wire CrOSS reference CHArT connector Make MoDel Year DeScrIPtIon audi name type PoSItIon VolkS WaGen PolarItY MoDUle location component locator A3 A4 S3 S4 TT New Beetle City Golf City Jetta Eos Golf Golf 3-door Golf 5-door GTI GTI GTI Jetta Jetta Passat Rabbit Tiguan

4 Page 4 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## TYPE 1 - wiring DIAGRAM TWO KEYS ARE REQUIRED FOR THIS INSTALLATION. ONE KEY WILL REMAIN PERMANENTLY IN THE VEHICLE. THE OTHER KEY WILL BE USED FOR THE PROGRAMMING PROCEDURE. IT WILL THEN BE RETURNED TO THE OWNER. TACH (AC) INPUT E-BRAKE STATUS (-) INPUT DISARM (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REMOTE STARTER <- OPTIONAL 5-6 LOOPS AROUND KEY IGNITION (+) INPUT/OUTPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT 5-6 LOOPS AROUND KEY BARREL N/A LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM (-) INPUT - BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE *E-BRAKE STATUS (-) OUTPUT - GREEN *TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK WHITE/RED (NC) WHITE YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - HOOD STATUS (-) OUTPUT* BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE (+) OUTPUT* PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) TWISTED WIRES IN DOOR HARNESS, IN DRIVER KICK PANEL CANL - ORANGE/BROWN CANH - ORANGE/LT. GREEN

5 Page 5 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## TYPE 2 - wire CrOSS reference CHArT connector Make MoDel Year DeScrIPtIon name type PoSItIon VolkS WaGen PolarItY MoDUle location component locator CC Passat Passat CC V ~ ~ ~ ~ Red/Black (+) Parking light switch ~ Parking Light ~ ~ ~ ~ White/Black ~ Parking light switch ~ Ignition ~ ~ ~ ~ Green/Gray (+) Ignition switch ~ Starter ~ ~ ~ ~ Red/Gray (+) Ignition switch ~ Keysense ~ ~ ~ ~ LtGreen (+) Ignition switch ~ Immobilizer 1 ~ ~ ~ ~ Black ~ ~ ~ Immobilizer 2 ~ ~ ~ ~ White ~ ~ ~ 12V ~ ~ ~ ~ Red/Black (+) Parking light switch ~ Parking Light ~ ~ ~ ~ White/Black ~ Parking light switch ~ Ignition ~ ~ ~ ~ Red/Violet (+) Ignition switch ~ Starter ~ ~ ~ ~ Red/Gray (+) Ignition switch ~ Keysense ~ ~ ~ ~ LtGreen (+) Ignition switch ~ Immobilizer 1 ~ ~ ~ ~ Black ~ ~ ~ Immobilizer 2 ~ ~ ~ ~ White ~ ~ ~ 12V ~ ~ ~ ~ Red/Black (+) Parking light switch ~ Parking Light ~ ~ ~ ~ White/Black ~ Parking light switch ~ Ignition ~ ~ ~ ~ Green/Gray (+) Ignition switch ~ Starter ~ ~ ~ ~ Red/Gray (+) Ignition switch ~ Keysense ~ ~ ~ ~ LtGreen (+) Ignition switch ~ Immobilizer 1 ~ ~ ~ ~ Black ~ ~ ~ Immobilizer 2 ~ ~ ~ ~ White ~ ~ ~

6 Page 6 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## TYPE 2 - wiring DIAGRAM 87 WIRES AT PARKING LIGHT SWITCH 12V (+) - RED/BLACK PARKING LIGHT - WHITE/BLACK 85 87A V (+) 85 87A FACTORY IMMOBILIZER WIRES RED/GRAY - STARTER (+) RED/VIOLET - IGNITION (+) WIRES AT IGNITION SWITCH THE KEYSENSE WIRE MUST BE POWERED BEFORE THE IGNITION WIRE LT. GREEN - KEYSENSE (+) 30 SWITCH SIDE VEHICLE SIDE BLACK WHITE REMOTE STARTER PARKING LIGHT (+) OUTPUT TACH (AC) INPUT DISARM (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT <- OPTIONAL STARTER (+) OUTPUT IGNITION (+) INPUT/OUTPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT DIODE 1N4001 DIODE 1N4001 N/A LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) 5-6 LOOPS AROUND KEYFOB USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM (-) INPUT - BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE (NC) GREEN *TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK WHITE/RED WHITE YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - HOOD STATUS (-) OUTPUT* BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - KEYSENSE AND IGNITION (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT TWO KEYS ARE REQUIRED FOR THIS INSTALLATION. ONE KEY WILL REMAIN PERMANENTLY IN THE VEHICLE. THE OTHER KEY WILL BE USED FOR THE PROGRAMMING PROCEDURE. IT WILL THEN BE RETURNED TO THE OWNER. BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED - BRAKE (+) OUTPUT GRAY/YELLOW (NC) TWISTED WIRES IN DOOR HARNESS, IN DRIVER KICK PANEL CANL - ORANGE/BROWN CANH - ORANGE/LT. GREEN

7 Page 7 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## TYPE 3 - wire CrOSS reference CHArT connector Make audi MoDel Year DeScrIPtIon name type PoSItIon PolarItY MoDUle location component locator A6 Q7 S

8 Page 8 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## TYPE 3 - wiring DIAGRAM REMOTE STARTER TACH (AC) INPUT E-BRAKE STATUS (-) INPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT <- OPTIONAL IGNITION (+) INPUT/OUTPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE *E-BRAKE STATUS (-) OUTPUT - GREEN *TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - HOOD STATUS (-) OUTPUT* BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE (+) OUTPUT* PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) TWISTED WIRES IN DOOR HARNESS, IN DRIVER KICK PANEL CANL - ORANGE/BROWN CANH - ORANGE/LT. GREEN

9 Page 9 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## TYPE 4 - wire CrOSS reference CHArT connector Make VolkSWaGen MoDel Year DeScrIPtIon name type PoSItIon PolarItY MoDUle location component locator Beetle Jetta CanH B White 73 pin 20 Orange/Green (DATA) BCM ~ CanL B White 73 pin 21 Orange/Brown (DATA) BCM ~ Doorlock A Black 73 pin 24 Blue/Red (MUX) BCM ~ CanH B White 73 pin 20 Orange/Green (DATA) BCM ~ CanL B White 73 pin 21 Orange/Brown (DATA) BCM ~ Doorlock A Black 73 pin 24 Blue/Red (MUX) BCM ~

10 Page 10 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## TYPE 4 - wiring DIAGRAM TWO KEYS ARE REQUIRED FOR THIS INSTALLATION. ONE KEY WILL REMAIN PERMANENTLY IN THE VEHICLE. THE OTHER KEY WILL BE USED FOR THE PROGRAMMING PROCEDURE. IT WILL THEN BE RETURNED TO THE OWNER. REMOTE STARTER 5-6 LOOPS AROUND KEY 5-6 LOOPS AROUND KEY BARREL TACH (AC) INPUT E-BRAKE STATUS (-) INPUT TRUNK (-) OUTPUT 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT <- OPTIONAL LOCK (-) OUTPUT UNLOCK (-) OUTPUT IGNITION (+) INPUT/OUTPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 12V (+) - RED (NC) GREEN/BLACK (NC) BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK WHITE/RED (NC) WHITE YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) B - WHITE CANL CANH BCM DOORLOCK (MUX) A - BLACK 180Ω

11 Page 11 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## TYPE 5 - wire CrOSS reference CHArT connector Make MoDel Year audi DeScrIPtIon name type PoSItIon VolkS WaGen PolarItY MoDUle location component locator A3 S3 Eos Golf 3-door Golf 5-door GLI GTI Jetta Passat Tiguan CanH C Brown 73 pin 20 Orange/LtGreen (DATA) BCM ~ CanH C Brown 73 pin 20 Orange/LtGreen (DATA) BCM ~ CanH C Brown 73 pin 20 Orange/LtGreen (DATA) BCM ~ CanH C Brown 73 pin 20 Orange/LtGreen (DATA) BCM ~ CanH C Brown 73 pin 20 Orange/LtGreen (DATA) BCM ~ CanH C Brown 73 pin 20 Orange/Green (DATA) BCM ~ CanH C Brown 73 pin 20 Orange/LtGreen (DATA) BCM ~ CanH C Brown 73 pin 20 Orange/Green (DATA) BCM ~ CanL C Brown 73 pin 20 Orange/Brown (DATA) BCM ~ CanH C Brown 73 pin 21 Orange/LtGreen (DATA) BCM ~ CanH C Brown 73 pin 20 Orange/LtGreen (DATA) BCM ~

12 Page 12 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## TYPE 5 - wiring DIAGRAM TWO KEYS ARE REQUIRED FOR THIS INSTALLATION. ONE KEY WILL REMAIN PERMANENTLY IN THE VEHICLE. THE OTHER KEY WILL BE USED FOR THE PROGRAMMING PROCEDURE. IT WILL THEN BE RETURNED TO THE OWNER. TACH (AC) INPUT E-BRAKE STATUS (-) INPUT DISARM (-) OUTPUT TRUNK (-) OUTPUT LOCK (-) OUTPUT UNLOCK (-) OUTPUT 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REMOTE STARTER <- OPTIONAL 5-6 LOOPS AROUND KEY IGNITION (+) INPUT/OUTPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT 5-6 LOOPS AROUND KEY BARREL N/A LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM (-) INPUT - BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK WHITE/RED (NC) WHITE YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT* BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) CANH CANL BCM C - BROWN

13 Page 13 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## Appuyer Press and et release relâcher le bouton de programming programmation button pour choisir to select installation mode d installation. mode. La LED DEL flashes clignote (1X) une once fois = DATA (1X) = MODE DATA La LED DEL flashes clignote (2X) deux twice fois = STANDARD (2X) = MODE HARDWIRE CÂBLAGE MODE STANDARD SÉLECTiOn installation DU MODE MODE D installation SELECTiOn 2! Appuyer Press and et hold tenir le bouton de programmation programming button jusqu à ce que la until DEL LED émette turns une solid lumière GREEN VERTE to register pour selection. enregistrer la sélection. Pour After changer registration, le mode follow d installation Factory Reset après Procedure avoir to enregistré change installation la sélection, mode suivre and restart la procédure this procedure. de réinitialisation et refaire la procédure ci-contre. PrOCÉDUrE MODULE DE PrOgrAMMing PrOgrAMMATiOn PrOCEDUrE MODULE 1 Insert key into ignition. Insérer la clé dans le contact. 3 Wait, LED will turn solid GREEN for Patienter, 2 seconds. la DEL émettra une lumière VERTE pendant 2 secondes. 2 ON ON Turn key to ON position. Tourner la clé à la position ON. 4 5 OFF OFF Turn key to OFF position. Tourner la clé à la position OFF. Module Programming Procedure Procédure completed. de programmation du module complétée.

14 Page 14 of 14 DBI-AL(DL)-VW1-EN Doc. No.: ##10232## identify VEHiCLE YEAr 1 Locate the Vehicle Identification Number (VIN) and identify the 10th character. 4 3 A 5 Y 1 N 5 T A L 8 D 5 R 0 X 2 Match the VIN s 10th character to its corresponding year. l > 1990 S > 1995 Y > > 2005 a > 2010 M > 1991 t > > > 2006 B > 2011 n > 1992 V > > > 2007 c > 2012 P > 1993 W > > > 2008 D > 2013 r > 1994 X > > > 2009 e > 2014 led StatUS Flashing RED DIaGnoStIcS DUrInG ProGraMMInG DUrInG remote Start WItH IGnItIon off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DiAgnOSTiCS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTOrY reset PrOCEDUrE 1 2 DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for 2 seconds. RESET COMPLETED. RECONNECT all connectors. 3 4 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. When LED flashes red, RELEASE programming button. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message.