Home Topload Washers

Size: px

Start display at page:

Download "Home Topload Washers"

Cathleen Richards
5 years ago
Views:

1 Home Topload Washers Refer to Page 3 for Model Numbers Parts TLW24C_ Part No R3 June 2018

3 Table of Contents Title Page Parts Ordering Information... 2 Serial Plate Location... 2 Model Identification... 3 Graphic Panel, Control Support Panel and Controls (Drawing 1 of 2)... 4 Graphic Panel, Control Support Panel and Controls (Drawing 2 of 2)... 6 Lid Switch Assembly... 8 Top, Lid and Hood Back Panel Fill Hose, Mixing Valve-to-Tub Cover Hose, Mixing Valve and Bracket Motor, Mounting Bracket and Belt Agitator, Fabric Softener Dispenser, Drive Bell, Hub and Lip Seal Kit and Washtub Outer Tub, Cover, Bearing and Seal Housing, Pressure Hose and Counterweight Drain Pump, Drain Hose and Siphon Break Kit Weldment and Bearing Assembly, Drive Shaft and Pulley Front Panel, Base Assembly and Cabinet Kit Lead-In Cord and Cable Ties Shipping Brace, Plug and Special Tools Output Board, Wire Harnesses and Wires Drive Control, Wire Harnesses and Wires Parts Index Copyright 2018, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher

4 If literature or replacement parts are required, contact the source from whom the machine was purchased or contact Alliance Laundry Systems at (920) for the name and address of the nearest authorized parts distributor. Parts Ordering Information For technical assistance, call the number listed below: (920) Ripon, Wisconsin When calling or writing about your product, be sure to mention model and serial numbers. Model and serial numbers are located on serial plate(s) as shown. Serial Plate Location Serial Plate TLW1851P_

5 Model Identification Information in this manual is applicable to these washer models: AWN43RSN115CW01 AWN43RSN115CW14 AWN43RSN115TW01 AWN63RSN115CW01 AWN63RSN115CW14 AWN63RSN115TW01 AWNE9RSN115CW01 AWNE9RSN115CW14 AWNE9RSN115TW

6 Graphic Panel, Control Support Panel and Controls (Drawing 1 of 2) Models AWN43RSN115CW01, AWN43RSN115CW14, AWN43RSN115TW01, AWN63RSN115CW01, AWN63RSN115CW14 and AWN63RSN115TW01 TLW1862P_

7 Graphic Panel, Control Support Panel and Controls (Drawing 1 of 2) REF PART NO. DESCRIPTION COMMENTS W End Cap Left Control Support Panel Screw Temperature Switch Model AWN43RSN115TW Temperature Switch Model AWN63RSN115TW Temperature Switch For load size knob LED Display Assembly Cycle Selector Switch Models AWN43RSN115CW01, AWN43RSN115CW14 and AWN43RSN115TW Cycle Selector Switch Models AWN63RSN115CW01, AWN63RSN115CW14 and AWN63RSN115TW W End Cap Right Screw Control Assembly Models AWN43RSN115CW01, AWN43RSN115CW14 and AWN43RSN115TW Control Assembly Models AWN63RSN115CW01, AWN63RSN115CW14 and AWN63RSN115TW Screw Hold-Down Clip Graphic Panel Models AWN43RSN115CW01 and AWN43RSN115TW Graphic Panel Models AWN63RSN115CW01 and AWN63RSN115TW Graphic Panel Model AWN43RSN115CW Graphic Panel Model AWN63RSN115CW Knob Assembly Push Button Switch Rocker Switch 17 D Screw

8 Graphic Panel, Control Support Panel and Controls (Drawing 2 of 2) Models AWNE9RSN115CW01, AWNE9RSN115CW14 and AWNE9RSN115TW01 TLW1852P_

9 Graphic Panel, Control Support Panel and Controls (Drawing 2 of 2) REF PART NO. DESCRIPTION COMMENTS W End Cap Left Control Support Panel Screw W End Cap Right Control Assembly Includes item Overlay Model AWNE9RSN115CW Overlay All other models Screw Hold-Down Clip Graphic Panel 10 D Screw Screw

10 Lid Switch Assembly TLW1832B_

11 Lid Switch Assembly REF PART NO. DESCRIPTION COMMENTS Lid Switch Assembly 2 M Screw 3 M Nut Screw Switch

12 Top, Lid and Hood Back Panel TLW1853P_

13 Top, Lid and Hood Back Panel REF PART NO. DESCRIPTION COMMENTS W Lid Screw Hood Back Panel Models AWNE9RSN115CW01, AWNE9RSN115CW14 and AWNE9RSN115TW Hood Back Panel All other models Screw Screw Bushing 7 D Disconnect Power Warning Label Models AWN43RSN115TW01, AWN63RSN115TW01 and AWNE9RSN115TW01 7 D Warning Label All other models Strain Relief Hold-Down Clip Inlet Deflector Inlet Cover Screw Drip Tray Lid Lock Screw Hinge Stop Clip Lid Lock Bezel W Top Panel Bleach Dispenser Lid Hinge Right Lid Hinge Left Lid Lock Catch Bumper

14 Fill Hose, Mixing Valve-to-Tub Cover Hose, Mixing Valve and Bracket TLW1861P_

15 Fill Hose, Mixing Valve-to-Tub Cover Hose, Mixing Valve and Bracket REF PART NO. DESCRIPTION COMMENTS Valve to Inlet Hose Hose Clamp Screw Mixing Valve Mounting Bracket Washer Filter screen Washer Flow restrictor; Water pressure reducer; Available for water pressure up to but not exceeding 120 psi Fill Hose 4 feet; Marked red for hot water Fill Hose 4 feet; Marked blue for cold water Washer Mixing Valve Screen P Mixing Valve Screw Hose Clamp Pressure Sensor

16 Motor, Mounting Bracket and Belt TLW1854P_

17 Motor, Mounting Bracket and Belt REF PART NO. DESCRIPTION COMMENTS Motor Motor Mount Bracket Screw Belt Nut Isolator Assembly Lower Washer Isolator Assembly Upper

18 Agitator, Fabric Softener Dispenser, Drive Bell, Hub and Lip Seal Kit and Washtub TLW1855P_

19 Agitator, Fabric Softener Dispenser, Drive Bell, Hub and Lip Seal Kit and Washtub REF PART NO. DESCRIPTION COMMENTS Screw Balance Ring Assembly 3 719P3 Washtub Kit Stainless steel Washtub Gasket 5 766P3A Hub and Lip Seal Kit DO NOT use any sealant other than P Sealant; Includes item 10 and installation tool P Sealant Use with hub and lip seal kit Washtub Hub Spline Insert Nut Bell and Transmission Tube Seal Screw Drive Bell Screw Bell Plug Straight Agitator Fabric Softener Dispenser Assembly

20 Outer Tub, Cover, Bearing and Seal Housing, Pressure Hose and Counterweight TLW1856P_

21 Outer Tub, Cover, Bearing and Seal Housing, Pressure Hose and Counterweight REF PART NO. DESCRIPTION COMMENTS Tub Cover Assembly Includes item Tub Cover Gasket P Outer Tub Assembly Outer Tub Kit Includes item 14 installed Leg Spring Marked with blue paint; Use to replace four rear springs Washer Screw Bracket Out-of-Balance Switch Assembly Leg Spring Marked with green paint; Use to replace two front springs Screw Counterweight Assembly Screw Leg Plate P3A Hub and Lip Seal Kit P Sealant Use with hub and lip seal kit 15 D Warning Label Models AWN43RSN115TW01, AWN63RSN115TW01 and AWNE9RSN115TW01 15 D Warning Label All other models Grommet Pressure Bulb Hose Clamp Cable Clip Tubing

22 Drain Pump, Drain Hose and Siphon Break Kit TLW1857P_

23 Drain Pump, Drain Hose and Siphon Break Kit REF PART NO. DESCRIPTION COMMENTS NA 451P3 Drain Extension Kit 1 562P3 Siphon Break Kit Siphon break kit MUST be installed in drain hose if drain receptacle is lower than cabinet top of washer Drain Hose Sleeve Standpipe Strap Drain Hose Hose Stand 6 F Hose Clamp Screw Pump and Bracket Hose Clamp Tub-to-Pump Hose Retainer Clip Strain Relief

24 Weldment and Bearing Assembly, Drive Shaft and Pulley TLW1858P_

25 Weldment and Bearing Assembly, Drive Shaft and Pulley REF PART NO. DESCRIPTION COMMENTS Drive Shaft RP Lower Bearing Weldment and Bearing Assembly Drive Pulley Spline Insert Nut

26 Front Panel, Base Assembly and Cabinet Kit GROUND WIRE TLW1842P_

27 Front Panel, Base Assembly and Cabinet Kit REF PART NO. DESCRIPTION COMMENTS NA 122P4P Porcelain Touch-Up Paint Bumper Pad Panel Locator Screw Bumper Pad Screw 6 D Screw Hold-Down Lug Hinge Warning Label WP Service Cabinet Kit Screw Leg and Stabilizer Assembly Screw Bracket Right Rubber Foot Base Assembly Leveling Leg Nut Friction Ring P3 Adjustable Leg Extension Kit Bracket Left Foam Pad Front Panel Pad Panel Locator Foam Pad WP Front Panel Screw Hold-Down Clip Front Panel Brace

28 Lead-In Cord and Cable Ties TLW1865P_

29 Lead-In Cord and Cable Ties REF PART NO. DESCRIPTION COMMENTS Cable Tie 6 inches: Push mount 2 F Cable Tie 6 inches 3 D Screw Lead-In Cord

30 Shipping Brace, Plug and Special Tools TLW1859P_

31 Shipping Brace, Plug and Special Tools REF PART NO. DESCRIPTION COMMENTS NA Foam Shipping Brace Install before moving washer Shipping Brace Install whenever moving washer; Remove before use Shipping Plug Install before moving washer to prevent tub from damaging cabinet 3 321P4 Spring Hook Tool For removal of module springs from outer tub 4 306P4 Hex Wrench Tool For removal of locknut from washtub hub 5 254P4P Agitator Hook Set of 2; Use to remove agitator from drive bell 6 293P4 Drive Bell Seal Tool For installation of Bell and Transmission Tube Seal

32 Output Board, Wire Harnesses and Wires Models AWNE9RSN115CW01, AWNE9RSN115CW14 and AWNE9RSN115TW01 TLW1860P_

33 Output Board, Wire Harnesses and Wires REF PART NO. DESCRIPTION COMMENTS Control Drive Harness Pressure Sensor Harness Lid Lock Harness Drain Pump Harness Screw Screw Drive Cover P Drive Control Assembly NOTE: Individual wires are not available separately. Order complete wire harness, or order wire by the foot. When applying terminals to wires, it is recommended that the terminals be soldered to the wires

34 Drive Control, Wire Harnesses and Wires Models AWN43RSN115CW01, AWN43RSN115CW14, AWN43RSN115TW01, AWN63RSN115CW01, AWN63RSN115CW14 and AWN63RSN115TW01 TLW1863P_

35 Drive Control, Wire Harnesses and Wires REF PART NO. DESCRIPTION COMMENTS NA Gauge Wire Black; Order wire by foot and terminals as required NA Gauge Wire Orange; Order wire by foot and terminals as required Hood Harness Pressure Sensor Harness Control Drive Harness Lid Lock Harness Drain Pump Harness Screw Screw Drive Cover P Drive Control Assembly NOTE: Individual wires are not available separately. Order complete wire harness, or order wire by the foot. When applying terminals to wires, it is recommended that the terminals be soldered to the wires

36 Notes

37 Parts Index A Adjustable Leg Extension Kit 566P Agitator Hook 254P4P B Balance Ring Assembly Base Assembly Bell and Transmission Tube Seal Bell Plug Belt Bleach Dispenser Bracket Bumper Bumper Pad Bushing D Disconnect Power Warning Label D Drain Extension Kit 451P Drain Hose Drain Hose Sleeve Drain Pump Harness , 33 Drip Tray Drive Bell Drive Bell Seal Tool 293P Drive Control Assembly P...31, 33 Drive Cover , 33 Drive Pulley Drive Shaft E End Cap W...5, W...5, 7 C Cable Clip Cable Tie F Control Assembly Control Drive Harness , 33 Control Support Panel Counterweight Assembly Cycle Selector Switch F Fabric Softener Dispenser Assembly Fill Hose Foam Pad Foam Shipping Brace Friction Ring Front Panel 38335WP...25 Front Panel Brace Front Panel Pad N/A items do not appear in index

38 G Graphic Panel Grommet H Hex Wrench Tool 306P Hinge Stop Clip Hold-Down Clip , 7, Hold-Down Lug Hinge Hood Back Panel Hood Harness Hose Clamp F Hose Stand Hub and Lip Seal Kit 766P3A... 17, 19 I LED Display Assembly Leg and Stabilizer Assembly Leg Plate Leg Spring Leveling Leg Lid W...11 Lid Hinge Lid Lock Lid Lock Bezel Lid Lock Catch Lid Lock Harness , 33 Lid Switch Assembly Lower Bearing 28944RP...23 M Mixing Valve P...13 Mixing Valve Mounting Bracket Mixing Valve Screen Motor Motor Mount Bracket Inlet Cover Inlet Deflector Isolator Assembly isolator Assembly N Nut M , K Knob Assembly L Lead-In Cord O Outer Tub Assembly P...19 Outer Tub Kit Out-of-Balance Switch Assembly Overlay N/A items do not appear in index

39 P Panel Locator Porcelain Touch-Up Paint 122P4P Pressure Bulb Pressure Sensor Pressure Sensor Harness , 33 Pump and Bracket Push Button Switch R Retainer Clip Rocker Switch Rubber Foot S Shipping Plug Siphon Break Kit 562P Spline Insert , 23 Spring Hook Tool 321P Standpipe Strap Straight Agitator Strain Relief Switch T Temperature Switch Top Panel W...11 Tub Cover Assembly Tub Cover Gasket Tubing Tub-to-Pump Hose Screw D , 7, 25 D M , 7, 31, , 7, 9, , 31, , , , Sealant P... 17, 19 Service Cabinet Kit 38612WP Shipping Brace V Valve to Inlet Hose W Warning Label D D D Washer Washtub Gasket Washtub Hub Washtub Kit 719P Weldment and Bearing Assembly N/A items do not appear in index

40 Wire, 12 Gauge Wire, 18 Gauge N/A items do not appear in index

Home Topload Washers

Home Topload Washers Refer to Page 3 for Model Numbers Parts TLW2C_203417 www.alliancelaundry.com Part No. 203417R7 February 2018 Table of Contents Title Page Parts Ordering Information... 2 Serial Plate