MIS SERIES. Mist Eliminator. Installed differential pressure gauge and optional zero air-loss drain valve. Air or Water Cooled Aftercooler

Transcription

1 MIS SERIES Mist Eliminator The ircel MIS Mist Eliminator ( scfm) provides a full line of mist eliminators to effectively remove oil, solids and water from your compressed air system. In addition, this technology can serve as an efficient prefilter and contaminant separator for refrigerated and desiccant compressed air dryers. y reducing the liquid loading potential and preventing liquid slugs from reaching the dryer, it will extend the life of your refrigerated dryer s heat exchanger or the life of desiccant in regenerative dryers. MIS-1500 MIS Series Features Low pressure differential P rated capacity under typical conditions. Long service life. Pressure vessel SME U Stamped National oard Registered. RN available upon request. Low pressure drop, maximum filter area and dirt capacity. Hinged flange and lift lug standard on closure flanges. Service access without breaking connections. Rugged enameled steel. onnections sizes from 2 to 10-inch NSI flange. Standard differential pressure gauge on all models. Optional zero-loss auto drain. White enamel interior coating. MIS Series Elements The ircel MIS Mist Eliminator features an element with patent pending urethane threaded end. This unique design requires no internal loose parts and no internal housing center core. This provides easy, hassle-free element changeout and reduces the overall initial unit shipping weight, saving on freight costs. The element is designed with optimum pleat spacing and fin depth to provide unsurpassed low differential pressure, dirt holding capacity, and efficiency. Filtration efficiency and permeability are based on independent laboratory testing by Interbasic Resources, Inc. Sustainable Energy Savings Pressure rop Reduces ompressor HP 4% per 8 PSI rop For every 8 psi pressure drop, compressor horsepower efficiency will be reduced by 4%. Therefore, the annual energy cost to run a typical 100 hp compressor with 85% efficiency compressor/motor can be figured as follows: onventional Filter: $0.07/KW-hr x 8760 hours x KW x 4% = $ Mist Eliminator: $0.07/KW-hr x 8760 hours x KW x 0.5% = $ (1 psi pressure drop = 0.5% compressor HP reduced) MIS SERIES Recommended Installation That s a savings of $ per year. Locating a mist eliminator downstream from the compressor effectively lengthens the maintenance cycle on all elements, significantly reducing costs of system maintenance. High efficiency pleated construction. High efficiency needled polyester outer layer particulate removal. Installed differential pressure gauge and optional zero air-loss drain valve. Two stage borosilicate glass coalescing media. Mist Eliminator* Unique threaded element design (patent pending) requires no internal loose parts and no internal housing center core. The filter element will collect particles greater than 1 micron with 99.5% efficiency. Particles 0.5 micron in size will be filtered at an efficiency of 99.3%. Special HE (958 media) element available for 0.1 micron particles filtered at an efficiency of 99.99%. ir ompressor ir or Water ooled ftercooler Separator ir Receiver (Wet) ir ryer

2 MIS SERIES TEHNIL SPEIFITIONS MIS SERIES Model omparison Model apacity 1 (SFM) onn. (NSI) OH O Service Space Weight (lbs) Maximum Pressure (psig) Optional Zero ir- Loss Element Model Number MIS / /F MIS-300E MIS / /F MIS-500E MIS / /F MIS-1000E MIS / /F MIS-1500E MIS / /F MIS-2000E MIS / /F MIS-3000E MIS / /F MIS-4500E MIS /F MIS-6500E MIS /F MIS-8000E 1 apacity rated at 100 psig operating pressure, 100 F inlet temperature. /F - onsult Factory Maximum working pressure: 250 psig over style: lind flange Operating temperature range: -20 F to 200 F arbon steel leg height: 12 (included in OH dimension above) ue to a continuous program of product improvement, specification and dimensions are subject to change without notice. MIS SERIES apacity orrection Factors To Size the Mist Eliminator apacity for ctual onditions djusted apacity = scfm x 1 x 2 To calculate the capacity of a given mist eliminator based on non-standard operating conditions, multiply the standard capacity by the appropriate correction factor. EXMPLE: Mist Eliminator Model: MIS-1000 Standard apacity: 1000 scfm ctual Operating onditions: 80 psig inlet pressure: 1 = F inlet temperature: 2 = 0.94 djusted apacity = 1000 scfm x 0.83 x 0.94 = 780 scfm The published standard capacities for compressed air mist eliminators are based on 100 psig inlet pressure and 100 F inlet temperature. When these conditions vary, a given mist eliminator will be able to filter either more or less compressed air than its standard capacity. There are two ways in which this information can be used. The first is to start with a specific mist eliminator size and recalculate its capacity based on the known operating conditions using the correction factors given below. The other, with a given set of operating conditions, is to select the proper mist eliminator size based on applying the correction factors to the flow rate. Examples based on applying the correction factors are shown below. apacity correction factors for differing system air pressure (1) System Pressure (psig) orrection Factor To Select the Mist Eliminator for ctual onditions djusted apacity = scfm/1/2 To choose a mist eliminator based on a given flow at non-standard operating conditions, divide the given flow by the appropriate correction factors. EXMPLE: Given Flow: 1000 scfm ctual Operating onditions: 80 psig inlet pressure: 1 = F inlet temperature: 2 = 0.94 djusted apacity = 1000 scfm / 0.83 / 0.94 = 1282 scfm djusted Mist Eliminator Model Size: MIS-1500 apacity correction factors for differing system air temperature (2) System Temperature ( F) orrection Factor irtec Global 1100 NW Loop 410 San ntonio, TX US PHONE +1 (210) SLES INFORMTION support@airtec.global

3 F SERIES High Efficiency ompressed ir Filters Versitile esign ircel s F series high efficiency filters include smart design features and innovative technology to provide a compressed air filtration solution for a wide range of applications. ircel s unique F series high efficiency filters are designed to combine high performance, energy savings, flexibility and optimum reliability. Top ap Unique push-fit design and double O-ring seal for simple and secure installation. Multi-layer Filtration eep bed multi-wrap borosilicate glass microfiber with stainless steel support cylinders and a polyester needle felt sleeve. End ap urable and non-corrosive glass filled nylon cap which is attached to the element with a multi-part urethane resin. irtec Global 1100 NW Loop 410 San ntonio, TX US PHONE +1 (210) SLES INFORMTION support@airtec.global

4 FETURES N ENEFITS aptive Piston Type O-Ring nnular Seal between head and bowl to prevent leaks External Ribs for easy service/ bowl removal High Quality luminum onstruction castings 100% leak-tested elta-p Gauge (standard) The dual-sided P gauge face is not pressurized. Unique magnetic sensor ensures superior performance. Pop-up P Indicators (optional) Nylon pop-up is available as a lower cost option. Remote ontact P larm (optional) ry contacts close at 6 psid to send a notification signal to a bell, light, or control panel. an be field installed. Modular NPT onnections option to bolt up to three filters together with High Nitrile O-ring connection to save space, offer ease with installation and eliminate leaks Only 4-7 clearance required for element removal Flat Spot to aid bowl removal Large apacity ondensate sump with space to install internal float drain Internal Ribs to secure element in-place and form quiet-air zone to prevent condensate re-entrainment Hexagon on ottom to aid in easy bowl removal utomatic Internal Float as standard ESSORIES Threaded NPT Side and ottom Port for external auto or manual drain ottom dapter Plate ( scfm) Removable drain adapter for ease of float drain maintenance. Simple disconnect of external drain when element is changed. Mounting rackets llows convenient wall mounting of single or multiple filters. Ring Spanner ids in easy bowl removal. Manual s vailable for all models. onnecting Kits vailable for models scfm. Port Plates llows for easy conversion from standard port size to match larger pipe size and reduce pipe fittings. Prevents costly oversizing of filters to pipe size.

5 F SERIES TEHNIL SPEIFITIONS Filter Flow rate imensions inches (mm) NPT connections Weight Replacement model scfm Nm 3 /h E In/Out Side ottom** lbs element model F20[*] (72) 1.38 (35) 7.32 (186) 2.95 (75) N/ 1/4 N/ 1/ [*]E F30[*] (72) 1.38 (35) 7.32 (186) 2.95 (75) N/ 3/8 N/ 1/ [*]E F65[*] (110) 1.50 (38) (273) 5.98 (152) 1.30 (33) 1/2 1/4 1/ [*]E F75[*] (110) 1.50 (38) (273) 5.98 (152) 1.30 (33) 3/4 1/4 1/ [*]E F100[*] (110) 1.50 (38) (358) 5.98 (152) 1.30 (33) 1 1/4 1/ [*]E F150[*] (110) 1.50 (38) (358) 5.98 (152) 1.30 (33) 1 1/4 1/ [*]E F225[*] (146) 2.01 (51) (484) 6.50 (165) 1.65 (42) 1 1/2 1/2 1/ [*]E F300[*] (146) 2.01 (51) (484) 6.50 (165) 1.65 (42) 1 1/2 1/2 1/ [*]E F450[*] (146) 2.01 (51) (484) 6.50 (165) 1.65 (42) 2 1/2 1/ [*]E F650[*] (146) 2.01 (51) (685) 6.50 (165) 1.65 (42) 2 1/2 1/ [*]E F1000[*] (230) 2.68 (68) (722) 7.01 (178) 1.65 (42) 3 1/2 1/ [*]E F1250[*] (230) 2.68 (68) (844) 7.01 (178) 1.65 (42) 3 1/2 1/ [*]E F1500[*] (230) 2.68 (68) (992) 7.01 (178) 1.65 (42) 3 1/2 1/ [*]E Notes * Fill in element grade (FP5, PF1, PF01, and reverse flow RPF1) to appropriate model number. ** With internal float drain removed (18mm) 2.81 (71mm) 2.81 (71mm) E E F20[*] to F30[*] F65[*] to F650[*] F1000[*] to F1500[*] oalescing Filters Vapor Filter Grade FP5 PF1 / RPF1 (reverse flow) PF01 Particle removal 5.0 micron 1.0 micron 0.01 micron 0.01 micron Maximum carryover at 68 F / 20 5 ppm 0.1 ppm 0.01 ppm ppm Recommended temperature 100 F / F / F / F / 25 Maximum temperature 248 F / F / F / F / 50 Pressure drop (clean and dry) 0.4 psid / 30 mbar 1.0 psid / 70 mbar 1.5 psid / 100 mbar 1.0 psid / 70 mbar Pressure drop (saturated) 1.0 psid / 70 mbar 2 psid / 140 mbar 3.0 psid / 210 mbar N/ Pressure drop (change element) 6.0 psid / 400 mbar 6.0 psid / 400 mbar 6.0 psid / 400 mbar see note Element media orosilicate Glass Microfiber arbon impregnated paper Maximum working pressure 232 psig / 16 barg (300 psig / 20 barg without auto float drain) Housing material High quality aluminum Note: ctivated charcoal () filters must not operate in oil saturated conditions and will not remove certain types of gases including carbon monoxide and carbon dioxide. hange interval depends on application. Please contact your distributor. orrection Factors For maximum flow rate, multiply model flow rate shown in the speciation chart by the correction factor corresponding to the working pressure. See specifications for maximum pressure. Note: To reduce pressure drop by 50%, reduce flow rate by 30%. Operating Pressure (psig) orrection Factor