5. Refer to GTR Workshop Manual, section: and disconnect battery ground cable.
|
|
- Chloe Armstrong
- 5 years ago
- Views:
Transcription
1 HYDRAULIC HOSE REPAIR REMOVAL PROCEDURE 1. Open door. 2. Turn ignition 'ON'. 3. Power the convertible top to the fully lowered position. 4. Turn ignition 'OFF'. 5. Refer to GTR Workshop Manual, section: and disconnect battery ground cable. 6. Refer to GTR Workshop Manual, section: and remove the left-hand central junction box (CJB) for access. 7. Refer to GTR Workshop Manual section and remove the overhead console. 8. Where installed, disconnect the microphone harness electrical connector. (Figure 1) 9. Refer to GTR Workshop Manual section and remove the sun visors. 10. Remove the sun visor retaining clips.
2 11. Remove the header rail retaining clip, and remove the trim finisher from the header rail. (Figure 2) 12. Remove the retaining studs from the header seal. (Figure 3)
3 13. Lift the rear edge of the header seal for access and remove the latch cover retaining screws. (Figure 4) 14. Remove the remaining latch cover retaining screws and remove the latch cover from header rail. (Figure 5)
4 15. Disconnect the convertible top electrical connector. (Figure 6) 16. Detach the hydraulic hose retaining clips from the lefthand upper A-pillar. (Figure 7)
5 17. Detach the sun visor electrical connectors from the latch assembly bracket. (Figure 8) 18. Slacken and remove the seven latch assembly to header rail lower retaining bolts. (Figure 9) 19. Slacken and remove the latch assembly to header rail upper retaining bolts. (Figure 10) CAUTION: When carrying out the following step 20, the retaining bolts installed in the openended slots MUST NOT BE DISTURBED.
6 20. Remove the latch assembly rear retaining bolts. (Figure 11) 21. Support the latch assembly and loosen but do not remove the retaining bolts installed in the rear slotted holes. (Figure 12) 22. Lower the latch assembly.
7 23. Mark the hydraulic hoses with locations and disconnect the hoses from the cylinder assembly. (Figure 13) 24. Remove the latch assembly. 25. Install suitable blanking plugs to the convertible top latch cylinder and hydraulic hoses. 26. Remove the tie strap retaining hydraulic hoses to the latch assembly. (Figure 14) 27. Remove and discard the cloth tape retaining the hydraulic hoses to the A-pillar at the top edge of the instrument panel. 28. Detach the hoses from retaining clips in left-hand fuse box (CJB) opening. (Figure 15)
8 CAUTION: The hydraulic hoses must be marked so the new hydraulic feed and return hoses are connected correctly. 29. Mark the hoses ready to be cut, approximately in the middle of the left-hand CJB opening, between the two retaining clips. 30. Route the hoses from behind the instrument panel to the lower A-pillar. 31. Cut both hydraulic hoses, and clean away any spilled fluid. (Figure 16).. HYDRAULIC HOSE REPAIR INSTALLATION PROCEDURE CAUTION: The unions must be turned counter clockwise to be installed on the hoses.
9 1. Install the outer unions to the ends of the hydraulic hoses. (Figure 17) CAUTION: When inserting the inner union and starting to screw it into the outer, there is a tapered lead on its clamp tube. This must be located into the hose inner diameter. If it is not mounted properly the hose will be pushed out of the outer union as the inner union is screwed in. If this happens then the hose will not be successfully clamped between the inner and outer parts of the union. 2. Install and fully tighten the inner unions to the hoses, and install blanking plugs to the unions. (Figure 18) 3. Route the new hydraulic hoses up the left-hand A-pillar behind the instrument panel. 4. Remove the blanking plugs from the unions. 5. Connect the hydraulic hose unions and fully tighten.
10 6. Attach the hoses to the retaining clips in left-hand CJB aperture. (Figure 19) 7. Install new cloth tape to retain the hoses to the A-pillar, at the top edge of the instrument panel. 8. Align the latch assembly to the vehicle. 9. Remove the blanking plugs and connect the hoses to the cylinder assembly. (Figure 20) 10. Secure hydraulic hoses to latch assembly with new tie straps. CAUTION: The hydraulic hoses must not be trapped or pinched during the latch installation procedure.
11 11. Align the latch assembly to the rear bolts, and install the latch assembly. (Figure 21) 12. Support the latch assembly and install but do not tighten the two top retaining bolts. (Figure 22) 13. Install but do not tighten the remaining retaining bolts. 14. Tighten the two top retaining bolts. 15. Tighten all remaining retaining bolts.
12 16. Attach the sun visor electrical connectors to the latch assembly bracket. (Figure 23) 17. Attach the hydraulic hose retaining clips to the left-hand upper A-pillar. (Figure 24)
13 18. Connect the convertible top electrical connector. (Figure 25) 19. Install the latch cover, and tighten the retaining screws. (Figure 26) 20. Lift the rear edge of the header seal for access and install the latch cover retaining screws. (Figure 27)
14 21. Install the retaining studs to the header seal. (Figure 28) 22. Loosely install the left-hand CJB as follows: (Figure 29) ^ Attach the battery positive cable. ^ Tighten the retaining nut. 23. Connect the two left-hand CJB electrical connectors. 24. Refer to GTR Workshop Manual, section: and connect battery ground cable. 25. Turn the ignition to the 'ON' position. 26. Power the convertible top to the fully raised position. 27. Power the convertible top to the fully lowered position.
15 28. Turn the ignition to the 'OFF' position. 29. Refer to GTR Workshop Manual, section: and disconnect the battery ground cable. 30. Disconnect the two left-hand CJB electrical connectors. 31. Remove the left-hand CJB as follows: (Figure 29) ^ Remove the retaining nut. ^ Detach the battery positive cable. 32. Inspect the hydraulic hose unions for leaks. CAUTION Suitable foam padding must be installed around the unions to protect against Noise, Vibration and Harshness (NVH) concerns. 33. If no leaks are evident, install insulation padding. 34. Install the trim finisher to the header rail, and install the retaining clip. (Figure 30) 35. Refer to GTR Workshop Manual, section: and perform the following: ^ Install the A-pillar trim panel. ^ Install the sun visor retaining clips ^ Install the sun visors
16 ^ Where installed, connect the microphone harness electrical connector. (Figure 31) 36. Refer to GTR Workshop Manual, section: and install the overhead console. 37. Refer to GTR Workshop Manual, section: and install the lefthand central junction box (CJB). 38. Refer to GTR Workshop Manual, section: and connect the battery ground cable. 39. Power the convertible top to the fully raised position. 40. Refer to GTR Workshop Manual, section: and remove the righthand luggage compartment side trim panel. CAUTION: Two fluid levels are marked on the pump reservoir body. The upper mark denotes the fluid level when the convertible top is fully lowered and the lower mark denotes the level when the convertible top is fully raised. 41. Check the convertible top hydraulic fluid level. 42. If the hydraulic fluid level is low perform the following: ^ Remove the hydraulic fluid reservoir filler plug. ^ Remove and discard the O-ring seal. ^ Using a suitable syringe, top-up the fluid until the correct level is achieved. ^ Install a new O-ring seal.
17 ^ Install the hydraulic fluid reservoir filler plug.
TOYOTA SOLARA EC REARVIEW MIRROR Section I - Installation Preparation
Section I - Installation Preparation Part Number: PT374-33020 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/compass 2 1 Hardware Bag 3 1 Installation
More informationTOYOTA COROLLA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationDVD REAR SEAT VIDEO SYSTEM
Read entire instructions thoroughly before starting. TOOLS REQUIRED: DVD REAR SEAT VIDEO SYSTEM MINIVANS WITH ROOF RAILS INSTALLATION INSTRUCTIONS Non-metal trim stick Phillips screwdriver T15, T20, T25
More informationSCION xb EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationCentral locking system
Page 1 of 11 57-39 Central locking system Assembly overview 1 - Vacuum line 2 - Right-front door lock actuator Removing and installing page 57-12 3 - Vacuum line connectors Disengage harness connectors
More informationTOYOTA TACOMA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-35052 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 1 T-tap Connectors,
More information394: Handsfree, Bluetooth Handsfree, Bluetooth
394: Handsfree, Bluetooth S80 (07-), 2008, B8444S, TF-80SC AWD, L.H.D, YV1AH852881073834, 073834 4/1/2013 PRINT 394: Handsfree, Bluetooth Handsfree, Bluetooth Installation instruction: 31310098 INTRODUCTION
More information900 Installation instructions. SCdefault
SCdefault 900 Installation instructions SITdefault Parking assistance (SPA) MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationSCION xb AUTO-DIMMING MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationTOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationTECHNICAL BULLETIN No:
CIRCULATE: TO TECHNICAL BULLETIN No: Date: 14 Mar 2006 Service Mgr Warranty Workshop Body Shop Parts X X X X X SECTION: 501-01 Passenger Compartment Water Ingress AFFECTED VEHICLE RANGE: Land Rover LR3
More informationSCION xa AUTO-DIMMING MIRROR Preparation
Preparation Part Number: PT374-52040 (Compass) PT374-21050 (Homelink) Kit Contents Item # Quantity Reqd. Description 1a 1 AD Mirror Assembly w/compass & Map Lights (P/N PT374-52040) 1b 1 AD Mirror Assembly
More information2000 Ranger Workshop Manual
SECTION 211-02: Power Steering 2000 Ranger Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/1/1999 Gear Torsion Bar Suspension Special Tool(s) Remover, Tie Rod End 211-001 (TOOL-3290-D)
More informationTOYOTA AVALON EC REARVIEW MIRROR
Section I - Installation Preparation Part Number: PT732-07000 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Full Mirror Assembly, Compass 2 1 Hardware Bag 3 1
More informationPage 1 of 33 SPECIFICATIONS 2013 Ford Edge 3.5L Eng Limited Print Date: TORQUE SPECIFICATIONS Description Nm lb-ft lb-in Assist handle bolts 9-80 B-pillar upper trim panel screw 9-80 C-pillar trim panel
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Rear Vision System Mirror Display 2013-Current Ram (Kit part number 1009-9518) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Rear
More informationSunroof / Moonroof: All Technical Service Bulletins Body - Water Leaks To The Interior assenger Compartment Water Ingress
2006 Land Rover LR3 (LA) V8-4394cc 4.4L Page 1 Sunroof / Moonroof: All Technical Service Bulletins Body - Water Leaks To The Interior assenger Compartment Water Ingress FFECTED VEHICLE RANGE: and Rover
More informationInstallation instructions, accessories RTI S80
Installation instructions, accessories Instruction No 8685714 Version 1.0 5 Part. No. RTI S80 Volvo Car Corporation RTI S80-8685714 - V1.0 Page 1 / 25 Equipment A0000161 A0000162 A0801178 D8802049 Page
More informationREMOVAL AND INSTALLATION
501-12-1 Instrument Panel and Console 501-12-1 REMOVAL AND INSTALLATION Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage
More informationInstallation instructions, accessories - Bluetooth, Mute kit XC / Volvo Car Corporation Göteborg, Sweden
XC90 Section Group Weight(Kg/Pounds) Year Month 3 393 0.5/1.1 2006 11 XC90 2003, XC90 2004, XC90 2005, XC90 2006, XC90 2007, XC90 2008, XC90 2009, XC90 2010 Page 1 of 15 Required tools A0000162 IMG-242205
More informationSaab 9-3 4D/5D M page 3 Saab 9-5 M page 17
SCdefault 900 Monteringsanvisning SITdefault MONTERINGSNVISNING INSTLLTION INSTRUCTIONS MONTGENLEITUNG INSTRUCTIONS DE MONTGE Saab 9-3 4D/5D M03-............................... page 3...................................
More informationPart Number: PT
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationInstallation instructions, accessories - Bluetooth XC / Volvo Car Corporation Göteborg, Sweden
XC90 Section Group Weight(Kg/Pounds) Year Month 3 393 1/2.2 2008 03 XC90 2003, XC90 2003, XC90 2004, XC90 2004, XC90 2005, XC90 2005, XC90 2006, XC90 2006, XC90 2007, XC90 2007, XC90 2008, XC90 2008, XC90
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Mirror Display Dodge Ram Kit Contents: Instruction Sheets Template Chassis Harness Endgate Handle with Camera Wire Ties (Qty: 17) Bottle of ZTech Plug for Non-Locking Endgates (Optional)
More informationTOYOTA RAV TRAILER WIRE HARNESS Section I Installation Preparation
Section I Installation Preparation Part Number: 08921-42900 Kit Contents Item # Quantity Reqd. Description 1 1 Converter 2 1 Wire harness 3 1 Sub wire harness No.1 4 2 Plastic Tie (300mm) 5 21 Plastic
More information2004 Lincoln LS Workshop Manual
SECTION 310-00: Fuel System 2004 Lincoln LS Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/23/2004 Fuel Tank and Filler Pipe Printable View (541 KB) Special Tool(s) Fuel Drain Hose
More informationSECOND ROW SEAT BELT SECOND ROW SEAT BELT. Second Row Seat Belt SB-13 EXPLODED VIEW SEAT BELT RETRACTOR < REMOVAL AND INSTALLATION >
SECOND ROW SEAT BELT Second Row Seat Belt EXPLODED VIEW SECOND ROW SEAT BELT INFOID:0000000012551454 A B C D E F G SB I J K L M N O AWHIA0861ZZ P 1. Seat belt height adjuster (LH/RH) 2. Seat belt retractor
More informationALLDATA Online Jaguar Vanden Plas V8-3996cc 4.0L DOHC (AJ27) SFI - Fuel...
Page 1 of 7 Removal NOTE: This removal/installation procedure is applicable to all tank assembly variants. 1. Remove the battery. Refer to 'Battery, Service and Repair.' See: Starting and Charging\Battery\Service
More informationInstallation instructions, accessories - Bluetooth, swan neck microphone
S80 (-06) / V70 XC (01-) / XC70 (-07) / S60 / V70 (00-08) / XC90 / S40 (04-) / V50 / C70 (06-) / S80 (07-) / C30 / V70 (08-) / XC70 (08-) Section Group Weight Year Month (Kg/Pounds) 3 394 0.5/1 2006 10
More informationPage 1 of 10 43: Transmission, automatic, B5254T2, AW50/51 AWD V70 XC (01-) / XC70 (-07), 2004, B5254T2, AW50/51 AWD, L.H.D, YV1SZ59H241147306, 147306 15/10/2011 PRINT 43: Transmission, automatic, B5254T2,
More informationSCdefault. 900 Installation instructions. Accessories Part No. Group Date Instruction Part No. Replaces :40-05 Sep
SCdefault 900 Installation instructions SITdefault Parking assistance (SPA) MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationX-TYPE. Inspection of Fuel Tank Harness Possible Connector Damage Service Action S947
SERVICE X-TYPE DATE 07/04 TECHNICAL BULLETIN Inspection of Fuel Tank Harness Possible Connector Damage Service Action S947 XT30-S947 MODEL VIN 2004 MY X-TYPE D55232-D7030 Issue: A concern has been identified
More informationConflicts. TOYOTA 4Runner REARSIGHT. Part Number: Code: MC90 KIT CONTENTS ADDITIONAL ITEMS REQUIRED FOR INSTALL RECOMMENDED TOOLS
TOYOTA 4Runner 2010 - REARSIGHT Part Number: 00016-00085 Code: MC90 Conflicts KIT CONTENTS ITEM QTY DESCRIPTION 1 1 MIRROR/MONITOR 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA EXTENSION HARNESS 4 1 SACK PARTS 5
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory NIGHT Application CR-V Publications No. AII 32951 Issue Date SEP 2006 PARTS LIST Automatic Day/Night Mirror Attachment Kit P/N 08V03-SWA-100 Harness cover set Automatic
More information* * APPLICABLE MODELS: 2014 > Mazda 3
PART NUMBER: 0000 8C L48 (DIO) / 0000 89 L84 (PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0700-000* APPLICABLE MODELS: 2014 > Mazda 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage
More information* * APPLICABLE MODELS: 2014 > Mazda 6
PART NUMBER: 0000 8C H02(DIO) / 0000 89 H18(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0694-000* APPLICABLE MODELS: 2014 > Mazda 6 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage
More information* * APPLICABLE MODELS: 2017 > CX-5
PART NUMBER: 0000 8C R06(DIO) / 0000 89 R28(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0681-000* APPLICABLE MODELS: 2017 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart
More information* * APPLICABLE MODELS: 2016 > CX-3
PART NUMBER: 0000 8C S01(DIO) / 0000 89 S07(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0688-000* APPLICABLE MODELS: 2016 > CX-3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart
More informationFRONT DOOR LOCK ACTUATOR (G531598)
PUBLISHED: 11-MAY-2011 2006.50 XK RANGE (X150), 501-14 HANDLES, LOCKS, LATCHES AND ENTRY SYSTEMS FRONT DOOR LOCK ACTUATOR (G531598) REMOVAL AND INSTALLATION REMOVAL 1. Remove the window regulator. For
More informationTECHNICAL BULLETIN No:
Date: 01 Mar 2007 CIRCULATE: TO Service Mgr Warranty Workshop Body Shop Parts X X X X X SECTION: REPLACES LS501-012, ISSUE 2, DATED 29-JUN-2006. CHANGES ARE HIGHLIGHTED WITH GREY BACKGROUND. 501-00 BODY
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)
More informationREMOVAL IR 11. Slide the inner rear view mirror.
11 Slide REMOVAL CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page RS-1). 1. DISCONNECT
More informationXJ range. Water Ingress Around Roof Opening Panel Restricted Drain Tubes Check/Reposition Drain Tubes
SERVICE XJ range DATE 03/05 TECHNICAL BULLETIN Water Ingress Around Roof Opening Panel Restricted Drain Tubes Check/Reposition Drain Tubes MODEL VIN XJ501-13 2004-05 MY XJ range G00001-G38526 Issue: Some
More informationGentex Autodim Homelink Compass Temperature Mirror Installation in 2014 Tacoma Purchased from Bob s Automotive Mirrors & More LLC (Robert Prim)
Gentex Autodim Homelink Compass Temperature Mirror Installation in 2014 Tacoma Purchased from Bob s Automotive Mirrors & More LLC (Robert Prim) This is my 50-GENK51A Gentex mirror kit and instructions.
More informationInstallation instructions, accessories. Handsfree, Bluetooth
Installation instructions, accessories Instruction No 31310097 Version 1.3 5 Part. No. 31285547 Handsfree, Bluetooth Volvo Car Corporation Handsfree, Bluetooth- 31310097 - V1.3 Page 1 / 28 Equipment A0000162
More informationFOLDING TOP HYDRAULIC CYLINDER HOSE IDENTIFICATION
Page 1 of 50 Service Manual: POWER ROOF SYSTEM AND Print Date: CONVERTIBLE TOP FOLDING TOP HYDRAULIC CYLINDER HOSE IDENTIFICATION Fig 1: View Of Folding Top Hydraulic Cylinder 2006 Pontiac G6 3.9L Eng
More informationModel Year: 2008 Model: xb Doc ID: RM000001XUW004X
1 of 18 2/28/2008 10:41 AM Last Modified: 2-12-2007 Service Category: Vehicle Interior 1.6 A Section: Interior Panels/Trim Model Year: 2008 Model: xb Doc ID: RM000001XUW004X Title: INTERIOR: ROOF HEADLINING:
More informationOil trap electrically heated, replacing
1(5) Oil trap electrically heated, replacing Removing Note! As the illustrations in the information are used for different model years and/or models, some variation may occur. However, the essential information
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Illuminated Kick Plate Maxima (Applicable ONLY to U.S. Market Vehicles with Build Date June 2012 or later) 999G6
More informationBMW 3Series (E46) Installation Guide StealthOne Version 1.6
BMW 3Series (E46) Installation Guide StealthOne Version 1.6 Copyright Fontana Enterprises, 2008 All rights reserved. Product Information Copyright Copyright Fontana Enterprises, 2008 All rights reserved.
More informationHow to fold your MGB top (pre 1970 pack away top & frame)
How to fold your MGB top (pre 1970 pack away top & frame) It is most important that the instructions given for raising, lowering and folding the hood are followed. Do not use undue force on the hood frame-members.
More informationGENUINE ACCESSORIES INSTALLATION INSTRUCTIONS. ITEM QTY DESCRIPTION Usage Chart Service Part Number. 1 1 Mirror Assembly w/ Compass 1
AUTO PART NUMBER: 0000 8C P4 (DIO)/ 0000 89 P25 (PIO) REQUIRED COMPONENTS: INSTALLATION KIT: 2 SA Harness - 2 Conductor 3 0 Wire Ties 4 Wire Cover 5 A-Pillar Tether Clip (D09W-6862) 6 3 Foam Tape 7 3 Electro-Tap(wire
More informationTECHNICAL BULLETIN No:
CIRCULATE TO: TECHNICAL BULLETIN No: Date: 20 MAY 2010 SERVICE PARTS WARRANTY BODY SHOP THIS BULLETIN SUPERSEDES LA501-12; CHANGES ARE LIMITED TO INSTRUCTING TECHNICIANS TO CARRY OUT THIS REPAIR PROCEDURE
More information2002 Explorer Sport/Sport-Trac Workshop Manual
Page 1 of 18 SECTION 501-12: Instrument Panel and Console REMOVAL AND INSTALLATION 2002 Explorer Sport/Sport-Trac Workshop Manual Instrument Panel Removal All vehicles CAUTION: Electronic modules are sensitive
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Versa Note 999F3 4Z000 - Accent Lighting Kit. 999Q9 AY000 - Accessory Service Connector
More informationRemoving and installing moulded headliner
Page 1 of 13 Removing and installing moulded headliner Special tools and workshop equipment required Removal lever -80-200- Front-end hook -3370- Removal wedge -3409- Removing Remove driver's seat: Audi
More informationInstallation instructions, accessories - Rear Seat Entertainment
XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 2004 10 XC90 2003, XC90 2004, XC90 2005, XC90 2006, XC90 2007, XC90 2008 Replaces issue: 2003 12 J3904620 Page 1 of 18 Required tools A0000162 A0000163
More information2003 Jaguar X-Type BRAKES' 'Disc - X-Type
REAR DISC BRAKE CALIPER WARNING: Brake dust, if inhaled can damage your health. Always remove brake dust using a vacuum brush. Do not use a compressed air line to disperse brake dust into the atmosphere.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit was designed for a standard single pump Radium Engineering
More informationALLDATA Online Jaguar Vanden Plas L6-3980cc 4.0L DOHC - Service and Rep...
Page 1 of 7 RENEW Jack up the front of the vehicle. Fit camber tie-down bars (Service Tool JD 133) to the road spring pans. NOTE: If, for any reason, the front crossmember is being stripped down, Service
More informationSECTION B: Supplemental Restraint System 2002 Lincoln LS Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/27/2004
SECTION 501-20B: Supplemental Restraint System 2002 Lincoln LS Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/27/2004 Clockspring Removal WARNING: Always wear safety glasses when
More informationYour G3 buggy is fitted with three switches on the front part of the body:
CONTENTS Buggy operation... 3 General Maintenance... 5 Technical Maintenance... 6 Front wheel bearing replacement... 6 Rear wheel bearing replacement... 7 Chain replacement... 8 Chain Adjustment... 9 Brake
More informationCHAPTER 21 ENVIRONMENT CONTROL. Section Title Page
CHAPTER 21 ENVIRONMENT CONTROL Section Title Page 21-00 Description........................................ 21.1 21-10 Ventilation........................................ 21.3 21-11 Nose Vent................................
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL ENGINE STARTER Application 2010 CR-V Publications No. AII 42612-42916 Issue Date OCT 2009 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-101B
More informationFuel pump unit, changing
1(11) Fuel pump unit, changing Special tools: 981 2270, 981 2273, 981 2282, 998 5972, 999 5484, 999 5485, 999 5561, 999 5666, 999 5673 Safety See first Safety regulations for handling fuel. Preparation
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Airbag replacement harness MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationModel(s) Year Eng. Code Trans. Type VIN Range From VIN Range To
Model(s) Year Eng. Code Trans. Type VIN Range From VIN Range To New Beetle 1998 > 1999 All 4-Speed Automatic (01M) All All Condition 01 07 17 Jan. 29, 2007, 2002393, Supersedes Technical Bulletin Group
More informationENGINE - V8. Seal - crankshaft - rear. Refit 1. Ensure both seal location and running surface on crankshaft are clean.
REPAIRS Seal - crankshaft - rear 1. Ensure both seal location and running surface on crankshaft are clean. 1. Automatic gearbox models: converter drive plate. ENGINE - V8, REPAIRS, Plate - drive - automatic.
More informationLEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Tow Hitch Wire Harness Kit Quest (2011) 999T8 NW000 Installation of this accessory requires installation of
More informationTOYOTA FJ CRUISER AIR DAM/LIGHT BAR Preparation
Preparation Part Number: PT278-35071 Kit Contents Item # Quantity Reqd. Description 1 1 Air Dam / Light Bar Hardware Bag 1 Contents Item # Quantity Reqd. Description 1 2 Screw, M6x33mm, Wafer Head 2 2
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory NIGHT Application 2007 CR-V Publications No. Issue Date SEP. 2006 PARTS LIST Automatic Day/Night Mirror Attachment Kit P/N 08V03-SWA-300 Harness cover set Automatic
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit
More informationJODALE PERRY. Parts List & Mounting Instructions. Jacobsen HR9016 JDP BUILT FOR LIFE
JODALE PERRY Parts List & Mounting Instructions Jacobsen HR9016 JDP BUILT FOR LIFE Jacobsen HR9016 Mounting Instructions Standard Parts 1 - LH Rear Mounting Bracket 1 - RH Rear Mounting Bracket 1 - Front
More informationInstallation instructions, accessories - Fuel driven heater 912-D
XC90 Section Group Weight(Kg/Pounds) Year Month 8 87 2002 10 XC90 2003 D5244T, XC90 2004 D5244T, XC90 2005 D5244T AW50/51 AWD, XC90 2006 D5244T, XC90 2006 D5244T AW50/51 AWD D5244T R8703687 Page 1 of 20
More informationPART NUMBER: H630SSJ000. Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4)
Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4) E. Clip B. Harness (1) C. Cable tie (8) F. Mounting Hardware (2) G. Replacement Speaker (2) H. HVAC Duct extension (2) IMPORTANT:
More informationAccessory Fitting Instructions
Accessory Fitting Instructions Side Mounted Licence Plate Kit - USA Only Kit Number A975070 Models Affected Bonneville Bobber, Bonneville Bobber - Black, Bonneville Speedmaster from VIN 794 Thank you for
More informationConflicts TOYOTA TACOMA HANDS FREE BLU TOOTH. Part Number: Accessory Code: BT4 ADDITIONAL ITEMS REQUIRED FOR INSTALL
TOYOTA TACOMA 2011 - HANDS FREE BLU TOOTH Part Number: 00016-00401 Accessory Code: BT4 Conflicts Factory Bluetooth System & JBL Audio KIT CONTENTS ITEM QTY DESCRIPTION 1 1 INTERFACE MODULE 2 1 INTERFACE
More informationFuel supply system, servicing (vehicles with front wheel drive and 1.8 ltr. turbo or 2.8 ltr. engine)
Page 1 of 49 20-6 Fuel supply system, servicing (vehicles with front wheel drive and 1.8 ltr. turbo or 2.8 ltr. engine) Note: VAG1921 spring clamp pliers are recommended for installation Always replace
More informationSCION FR-S FOG LIGHTS
Part #: PT413-18130 Conflicts: Lowering Springs PTR07-18130-LL (California only) Kit Contents: For Anniversary Edition, Monogram & RS 2.0 vehicles, additional parts need to be ordered (PT413-18130-LL)
More informationDVS Cypress Face Installation Instructions (SKU )
Table of Contents Compatibility... 1 Packing List... 1 Installation... 2 Prepare the Insert for Face Installation... 2 Attach the Surround Panels (if applicable)... 6 Assemble the Face... 7 Attach the
More informationPage 1 of 15 2011 Glass, Frames and Mechanisms - Rear Quarter Window Regulator Motor Removal and Installation Removal 1. Remove the rear quarter trim panels. For additional information, refer to: Rear
More informationFuel Injector ( )
Published: Mar 29, 2010 Fuel Injector (196010) Special Service Tools Fuel Injector remover 303-1127 Removal WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near
More informationINSTALLATION MANUAL HYDRAULIC HOSE REEL
INSTALLATION MANUAL HYDRAULIC HOSE REEL 1 TABLE OF CONTENTS SECTION PAGE SECTION PAGE 1 HOW TO ORDER PARTS 3 MAINTENANCE SCHEDULE... 11 1.1 HOW TO ORDER PARTS... 2 1.2 MODEL IDENTIFICATION... 3 2 INSTALLATION
More informationTOYOTA RAV HANDS FREE PHONE INTERFACE 9/06/06
9/06/06 Part Number: 00016-32103-01;00003-04 Accessory Code: BT1 Kit Contents Item # Quantity Reqd. Description 1 1 UIB -USER INTERFACE 2 1 CONTROL MODULE 3 1 USER GUIDE 4 1 HARDWARE BAG 5 1 INSTALLATION
More information1. Open front door (20124) and support using Rotunda Flexi-Work Table or equivalent.
file://c:\tso\tsocache\vdtom_3244\svk~us~en~file=svk13002.htm~gen~ref.htm Page 1 of 6 Section 01-03: Doors and Liftgate REMOVAL AND INSTALLATION 1997 Aerostar, Ranger Workshop Manual Doors Front Doors
More informationWiper arm and wiper motor, headlamp, replacing
"VCC137971 EN 20110112" file://c:\info\vv132007\ie\en\31\vcc137971.htm Page 1 of 2 Wiper arm and wiper motor, headlamp, replacing Removal Preparations Switch off the ignition. Headlamp wiper arm Lift up
More informationDear Customers. : i MiEV INSTRUMENT PANEL ILLUMINATION INSTALLATION AND HANDLING INSTRUCTIONS. Attention
Dear Customers Thank you for purchasing a Mitsubishi genuine optional part. For proper use of the product, please read this leaflet thoroughly. It is recommended you keep this leaflet at hand for future
More informationSCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationSCION XB SUBWOOFER ENCLOSURE Preparation
Preparation Part Number: Kit Contents Item # Quantity Reqd. Description 1 1 Subwoofer enclosure 2 1 Wire Harness 3 1 Paper Template 4 1 Plastic Drill Template 5 1 Hardware Bag Hardware Bag Contents 1 Item
More informationScion xd EC Rearview Mirror Preparation
Scion xd 2010 - EC Rearview Mirror Preparation Part Number: 00016-09101 Code: CM9 Kit Contents Item # Quantity Reqd. Description 1 1 Mirror Assembly w/ Compass and Homelink 2 1 Hardware bag Hardware Bag
More informationAccessory Fuse Block. Please read this entire manual before proceeding with installation.
Accessory Fuse Block Please read this entire manual before proceeding with installation. Kit Components: (1) Fuse Block Assembly (1) Harness (1) Positive power cable (1) Negative power cable (5) Pigtails
More informationIR Temp Probe. Toyota Sienna Rear Sight. Part Number: Accessory Code:MC1
Toyota Sienna 200 - Rear Sight Part Number: 0006-00085 Accessory Code:MC Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 2 3 4 5 6 7 8 MIRROR/MONITOR REVERSE MINI-CAMERA
More informationAccessory Kit Estimated Fitting Time: 120 Minutes
Landcruiser LC00 Tow-Pro Wiring Kit - Landcruiser LC00 Kit Part No: TPWKIT - 005 Accessory Kit Estimated Fitting Time: 0 Minutes FI88 Page 0 of Issue: Date: 7/09/07 07 General Notes Safety Notes Parts
More informationw w w. h d o n l i n e s h o p. d e CRUISE CONTROL KIT GENERAL INSTALLATION -J04064 REV Kit Number Models Additional Parts Required
-J006 REV. 006-08- CRUISE CONTROL KIT GENERAL Kit Number 7796-07 Models For the most up-to-date model fitment information, please see the product label or www.harley-davidson.com. Additional Parts Required.
More informationRECOMMENDED SEQUENCE OF APPLICATION
TOYOTA TACOMA 2010- PART NUMBER: 250-8403 REARSIGHT KIT CONTENTS ITEM QTY DESCRIPTION 1 1 INTERFACE ADAPTER HARNESS 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA INTERFACE HARNESS 4 1 SACK PARTS COLOR APPLICABILITY/TRIM
More informationFUEL PUMP UNIT, REPLACEMENT. Special tools: , , , , , , , ,
FUEL PUMP UNIT, REPLACEMENT Special tools: 981 2270, 981 2273, 981 2282, 998 5972, 999 5484, 999 5485, 999 5561, 999 5666, 999 5673 Safety See first: Safety regulations for handling fuel See: Service Precautions
More information