ALLDATA Online Jaguar Vanden Plas L6-3980cc 4.0L DOHC - Service and Rep...

Size: px
Start display at page:

Download "ALLDATA Online Jaguar Vanden Plas L6-3980cc 4.0L DOHC - Service and Rep..."

Transcription

1 Page 1 of 7 RENEW Jack up the front of the vehicle. Fit camber tie-down bars (Service Tool JD 133) to the road spring pans. NOTE: If, for any reason, the front crossmember is being stripped down, Service Tool JD 115 must be used in place of JD 133, and the coil springs must be removed prior to crossmember removal. JD 1 33 is for operations where the crossmember is being removed for access only. Lower the vehicle and settle the suspension. Open the bonnet. Engage the camber tie-down bars in the suspension turrets. Remove the front shock absorber upper securing nuts, washers and buffers (Fig 1). Slacken off the road wheel nuts 1/4 of a turn each. Jack up the front of the vehicle. Support with axle stands. Mark the wheel to stud relationship, and remove the front road wheels. Disconnect the left hand brake pad wear sensor block connector.

2 Page 2 of 7 Remove the lower guide pin bolt from the left hand caliper, and pivot the caliper upwards to gain access to the brake pads (Fig 2). NOTE: Use an open-ended spanner to hold the guide pin during removal. This will prevent damage to the rubber dust cover. Remove the brake pads. Remove the upper guide pin bolt, remove the caliper, and re-position the caliper away from the suspension area. Disconnect the right hand brake pad wear sensor block connector. Remove the right hand brake pads and caliper. Turn the steering to the straight ahead position. Remove the ignition key.

3 Page 3 of 7 Remove the lower column (3, Fig 3) to steering rack securing bolt/nut (1,2, Fig 3). Disengage the splines from the rack pinion (4, Fig 3). NOTE: At this point, the lower column cannot be completely disconnected from the pinion. Remove the P.A.S. pipe to crossmember retaining clamps and spacing washers. Position a drain tray under the front of the vehicle. Disconnect the steering rack return pipe, and drain the system. Fit blanking plugs to the pipe and rack. Disconnect the steering rack feed pipe, and drain the system. Fit blanking plugs to the pipe and rack. Re-position the pipes away from the suspension area. Remove the drain tray. Remove the engine mounting securing nuts.

4 Page 4 of 7 Attach JD 124 rear engine lifting eye, fit and align Service Tool MS 53B engine support bracket (Fig 1). Engage the hook to the lifting eye (2.9 ENGINE ONLY). Disconnect Nos. 1 and 2 plug leads.

5 Page 5 of 7 Attach 18G 1465 rear engine lifting eye, fit and align Service Tool MS 53B engine support bracket (Fig 2). Engage the hook to the lifting eye (3.6 ENGINE ONLY). Tighten the hook nut to take the weight of the engine. Slacken off the crossmember rear mounting bolts/nuts. Remove the nuts. Do not remove the bolts at this stage. Slacken off the mounting clamp plate securing bolts (Fig 3). Take the weight of the crossmember assembly on the jack. Finally, remove the rear mounting bolts and spacers. Remove the crossmember front mounting to chassis securing nuts (Fig 4). NOTE: The bolts nuts remain captive. Carefully lower the assembly from the vehicle. Ensure that the calipers, pipes and lower column do not foul during removal. Change over all ancillary components to the new crossmember. Position the crossmember assembly on the jack under the vehicle.

6 Page 6 of 7 Raise the assembly into position and align the shock absorbers. Align the engine mountings, P.A.S. pipes, lower column and rear mountings. Align the front crossmember mounting securing bolt holes. Fit and tighten the front mounting securing bolts (Fig 4). Using a second jack, align the left hand rear mounting (Fig 3). Fit and align the outer spacer. Fit the bolt through the chassis, the outer spacer and the mounting. Fit the inner spacer. Push the bolt fully home, fit but do not tighten the nut. Lower and remove the jack from under the mounting. Repeal the above procedure for the right hand rear mounting. Lower and remove the jack from under the crossmember. Finally tighten the rear mounting securing bolts/nuts. Tighten the rear mounting clamp plate securing bolts. Ensure the steering wheel and rack are in the straight ahead position. Re-position the lower column on to the pinion and align the clamp slot. Fit and tighten the clamp bolt/nut. Remove the blanking plugs from the P.A.S. pipes and rack. Fit new 'O' rings to the pipes. Connect the pipes to the rack. Tighten the union nuts. Refit the P.A.S. pipe clamps. Slacken off the MS 53B hook nut. Remove the hook. Remove Service Tool MS 53B. Remove the lifting eye. Fit and tighten the engine mounting securing nuts. Refit the calipers. Refit the brake pads. Refit the road wheels. Lower the vehicle from the axle stands. Settle the suspension. Refit the shock absorber upper buffers, washers, and securing nuts. Release the tie-down bars from the suspension. Raise the vehicle. Remove the tie-down bars from the road spring pans. Lower the vehicle.

7 Page 7 of 7 Bleed the P.A.S. system as follows: Top up the P.A.S. reservoir. Start the engine. Turn the steering wheel to full left hand lock. Turn the steering wheel to full right hand lock. Top up the reservoir. Fit the reservoir cap. Close the bonnet.

SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING

SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically

More information

1993 SUSPENSION Volkswagen Rear. EuroVan

1993 SUSPENSION Volkswagen Rear. EuroVan Article Text ARTICLE BEGINNING 1993 SUSPENSION Volkswagen Rear EuroVan DESCRIPTION Suspension uses control arms and axle beam for stabilization. Control arms and axle beam are combined as one unit. Brake

More information

SECTION H STEERING. Section Description Page No. H.1 GENERAL DESCRIPTION 3 H.2 STEERING WHEEL 3 H.3 INNER COLUMN 5 H.

SECTION H STEERING. Section Description Page No. H.1 GENERAL DESCRIPTION 3 H.2 STEERING WHEEL 3 H.3 INNER COLUMN 5 H. SECTION H STEERING Section Description Page No. H.1 GENERAL DESCRIPTION 3 H.2 STEERING WHEEL 3 H.3 INNER COLUMN 5 H.4 OUTER COLUMN 5 H.5 STEERING UNIT LOCK STOPS 6 H.6 STEERING UNIT 6 H.7 STEERING ARMS

More information

Steering Gear Replacement

Steering Gear Replacement Page 1 of 7 Steering Gear Replacement Removal Procedure Notice: With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column

More information

file://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref...

file://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref... Page 1 of 14 SECTION 211-02: Power Steering 1999 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 07/27/1998 Gear 5.0L Removal 1. Place the front wheels in the straight

More information

HEIDTS SUPERIDE IRS INSTALLATION INSTRUCTIONS INDEPENDENT REAR SUSPENSION

HEIDTS SUPERIDE IRS INSTALLATION INSTRUCTIONS INDEPENDENT REAR SUSPENSION HEIDTS SUPERIDE IRS INDEPENDENT REAR SUSPENSION Please read these instructions completely before starting your installation. Remember the basic rule for a successful installation: Measure Twice, Weld Once.

More information

See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )

See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( ) Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

1990 SUSPENSION Front ES250, LS400

1990 SUSPENSION Front ES250, LS400 SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,

More information

ARTICLE BEGINNING DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Rear. Golf III

ARTICLE BEGINNING DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Rear. Golf III Article Text ARTICLE BEGINNING 1995-96 SUSPENSION Rear Golf III DESCRIPTION Suspension uses control arms and axle beam for stabilization. Control arms and axle beam are combined as one unit. Brake drums

More information

~ Installing the Coil-Spring Front End ~

~ Installing the Coil-Spring Front End ~ 1935-1940 Ford Car & 1935-1941 Ford Truck Chassis Coil-Spring Front & Leaf Spring Rear Tech line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work!

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

Chapter 10 Suspension and steering

Chapter 10 Suspension and steering Chapter Suspension and steering Contents Control arm balljoint - renewal...............................7 Control arm bushes - renewal...............................6 Front anti-roll bar - removal and refitting.......................8

More information

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS XJ SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 7 page REAR SUSPENSION... 16 ALIGNMENT TABLE OF CONTENTS page AND WHEEL ALIGNMENT...1 DIAGNOSIS AND TESTING SUSPENSION

More information

INSTALLATION INSTRUCTION Rev A

INSTALLATION INSTRUCTION Rev A INSTALLATION INSTRUCTION 88587 Rev A FOR RANCHO SUSPENSION SYSTEM RS6587B: 2009 DODGE RAM 1500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:

More information

Page 1 of 11 1Search FRAME CROSS BAR 2001 Chrysler PT Cruiser 2.4L Eng Base CAUTION: DO NOT attempt to modify any suspension or steering components by heating or bending. Removal [ STABILIZER BAR ] 1.

More information

INSTALLATION INSTRUCTION 88581

INSTALLATION INSTRUCTION 88581 INSTALLATION INSTRUCTION 88581 FOR RANCHO SUSPENSION SYSTEM RS6581B: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES! WARNING: This suspension

More information

2001 Toyota MR ENGINES' '1.8L 4-Cylinder

2001 Toyota MR ENGINES' '1.8L 4-Cylinder TIMING CHAIN Removal 1. Disconnect negative battery cable. Drain cooling system. On Corolla, remove windshield washer fluid reservoir. On Celica, remove upper front fender apron seal and upper radiator

More information

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT:

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT: 55-59 Chevy Truck Chassis Custom IFS & 4-Link Install Instructions Tech line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE PARTS LIST

More information

INSTALLATION INSTRUCTIONS CHEVROLET NOVA (NVR-301) INDEPENDENT REAR SUSPENSION

INSTALLATION INSTRUCTIONS CHEVROLET NOVA (NVR-301) INDEPENDENT REAR SUSPENSION INSTALLATION INSTRUCTIONS 68-74 CHEVROLET NOVA (NVR-301) INDEPENDENT REAR SUSPENSION Please read these instructions completely before starting your installation. Assemble suspension on vehicle before powder-coating

More information

INSTRUCTION G-Comp Rear Suspension: Chevy Camaro. Kit Contents:

INSTRUCTION G-Comp Rear Suspension: Chevy Camaro. Kit Contents: INSTRUCTION 350-700 G-Comp Rear Suspension: 70-81 Chevy Camaro Speedway Motors, Inc. 2017 Kit Contents: 350700.1 G-Comp Crossmember & Chassis Brace 350700.2 G-Comp Rear Crossmember Assembly 350700.3 G-Comp

More information

1994 Mazda MX-5 Miata. SUSPENSION - FRONT 1994 SUSPENSION Mazda - Front

1994 Mazda MX-5 Miata. SUSPENSION - FRONT 1994 SUSPENSION Mazda - Front SUSPENSION - FRONT 1994 SUSPENSION Mazda - Front DESCRIPTION An independent front suspension with MacPherson-type struts is used on all models. Miata uses double wishbone design upper and lower control

More information

INSTALLATION INSTRUCTION 88088

INSTALLATION INSTRUCTION 88088 INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:

More information

INSTALLATION INSTRUCTION 89400

INSTALLATION INSTRUCTION 89400 INSTALLATION INSTRUCTION 89400 FOR RANCHO SUSPENSION SYSTEM RS66400B: 2012 RAM 1500 4WD. READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:

More information

SUSPENSION 2-1 SUSPENSION CONTENTS

SUSPENSION 2-1 SUSPENSION CONTENTS TJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 6 page REAR SUSPENSION... 13 ALIGNMENT INDEX page DESCRIPTION AND OPERATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION

More information

Installation Instructions Tubular A-Arm Front Suspension

Installation Instructions Tubular A-Arm Front Suspension 11 Mennonite Church Road Spring City, PA 19475 (610) 948-7303 Installation Instructions Tubular A-Arm Front Suspension (Mustang II -Style) CAUTION!!! The most important requirement for a successful installation

More information

WIDE RIDE IFS (STOP --- READ ALL THE DIRECTIONS FIRST!)

WIDE RIDE IFS (STOP --- READ ALL THE DIRECTIONS FIRST!) WIDE RIDE IFS We are happy to inform you that you have purchased the best I.F.S. kit on the market for you truck. The NO LIMIT WIDE-RIDE I.F.S. is our own design, based on years of truck building experience.

More information

SUSPENSION 2-1 SUSPENSION CONTENTS

SUSPENSION 2-1 SUSPENSION CONTENTS ZJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 6 page REAR SUSPENSION... 14 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION

More information

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS DN SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION - 4x2... 6 page FRONT SUSPENSION - 4x4... 14 REAR SUSPENSION... 23 ALIGNMENT TABLE OF CONTENTS page AND OPERATION WHEEL

More information

DRIVE AXLES. Differentials & Axle Shafts - Corvette

DRIVE AXLES. Differentials & Axle Shafts - Corvette DESCRIPTION & OPERATION 1998-99 DRIVE AXLES Differentials & Axle Shafts - Corvette A Getrag 625 model differential is used on both the automatic and manual transmissions. Differential carrier and case

More information

Ford Passenger Cars Mustang II Independent Front Suspension Installation Instructions

Ford Passenger Cars Mustang II Independent Front Suspension Installation Instructions 1935-1948 Ford Passenger Cars Mustang II Independent Front Suspension Installation Instructions 1-866-925-1101 www.totalcostinvolved.com The installation of the Total Cost Involved's Mustang Independent

More information

To Order Call (562)

To Order Call (562) 451 Park Industrial Dr. La Habra CA 90631 Phone: (562) 691-7006 Fax: (562) 691-5708 www.kugelkomponents.com 2017 PRICE SHEET #17 INDEPENDENT FRONT SUSPENSION SYSTEMS For All IFS Powder Coated (Black Only):

More information

Chapter 10 Suspension and steering

Chapter 10 Suspension and steering 10 1 Chapter 10 Suspension and steering Contents Front hub bearings - renewal 3 Front swivel hub assembly - removal and refitting 2 Front suspension and steering check See Chapter 1 Front suspension anti-roll

More information

INSTALLATION INSTRUCTIONS 88518

INSTALLATION INSTRUCTIONS 88518 INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:

More information

ENGINE - V8. Seal - crankshaft - rear. Refit 1. Ensure both seal location and running surface on crankshaft are clean.

ENGINE - V8. Seal - crankshaft - rear. Refit 1. Ensure both seal location and running surface on crankshaft are clean. REPAIRS Seal - crankshaft - rear 1. Ensure both seal location and running surface on crankshaft are clean. 1. Automatic gearbox models: converter drive plate. ENGINE - V8, REPAIRS, Plate - drive - automatic.

More information

FRONT AXLE GROUP 11A CONTENTS 11A-0. SECTION 0 GENERAL Removal 3 SECTION 1 FRONT AXLE HUB 1

FRONT AXLE GROUP 11A CONTENTS 11A-0. SECTION 0 GENERAL Removal 3 SECTION 1 FRONT AXLE HUB 1 11A-0 GROUP 11A FRONT AXLE CONTENTS SECTION 0 GENERAL 1 1-1 Removal 3 SECTION 1 FRONT AXLE HUB 1 1-2 Inspection 3 1-3 Installation 4 1. Removal and Installation 1 1-1 Removal 1 SECTION 3 WHEEL ALIGNMENT

More information

FRONT SUSPENSION LOCATION INDEX

FRONT SUSPENSION LOCATION INDEX 1. Remove the front suspension tower bar. (See FRONT SUSPENSION TOWER BAR REMOVAL/INSTALLATION.) 2007 Mazda MX-5 Miata Sport 2007 SUSPENSION Front Suspension - MX-5 Miata FRONT SUSPENSION LOCATION INDEX

More information

SECTION D REAR SUSPENSION. Section Description Page D.1. REMOVING AND REFITTING A REAR SUSPENSION UNIT 5

SECTION D REAR SUSPENSION. Section Description Page D.1. REMOVING AND REFITTING A REAR SUSPENSION UNIT 5 SECTION D REAR SUSPENSION Section Description Page D.1. REMOVING AND REFITTING A REAR SUSPENSION UNIT 5 D.2. REMOVING AND REFITTING THE COMPONENTS OF THE REAR SUSPENSION 8 D.3. CHECKING AND OVERHAULING

More information

1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series

1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - V Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - V Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet

More information

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES 2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential

More information

1970 Trans-Am Mustang Front Suspension Instructions. Manual, Volume One, Chassis. Special instructions and precautions will be given

1970 Trans-Am Mustang Front Suspension Instructions. Manual, Volume One, Chassis. Special instructions and precautions will be given 1970 Trans-Am Mustang Front Suspension Instructions 1. This kit was designed to be used in conjunction with the Rear Suspension kit. 2. This conversion follows standard procedures as described in the 1970

More information

Steering Column. Steering Column Component Layout.

Steering Column. Steering Column Component Layout. Page 1 of 9 Published : May 5, 2004 Steering Column Steering Column Component Layout Item Part Number Description 1 - Screw (3 off) 2 - Steering angle sensor 3 - Upper steering column assembly 4 - Cowl

More information

Your G3 buggy is fitted with three switches on the front part of the body:

Your G3 buggy is fitted with three switches on the front part of the body: CONTENTS Buggy operation... 3 General Maintenance... 5 Technical Maintenance... 6 Front wheel bearing replacement... 6 Rear wheel bearing replacement... 7 Chain replacement... 8 Chain Adjustment... 9 Brake

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

Note: The transmission mount just happened to be upside down in this picture. (c) 2015 Total Cost Involved Engineering, Inc. All Rights Reserved.

Note: The transmission mount just happened to be upside down in this picture. (c) 2015 Total Cost Involved Engineering, Inc. All Rights Reserved. 1970-1981 Chevy Camaro & Pontiac Firebird Custom IFS Installation Instructions 1-855-693-1259 www.totalcostinvolved.com CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLATION. IF ANY

More information

SCION tc LOWERING SPRINGS Preparation

SCION tc LOWERING SPRINGS Preparation Preparation Part Number: PTR11-21100 PTR11-21100-50 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 2 Locking Nut 4 2 Spring Bumper, Front 5 1 Instruction Form Hardware

More information

REAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION TRAILING ARM ASSEMBLY REAR SUSPENSION DIAGNOSIS

REAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION TRAILING ARM ASSEMBLY REAR SUSPENSION DIAGNOSIS 34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION......... 34-2 DIAGNOSIS.. 34-3 INTRODUCTION TO DIAGNOSIS........................ 34-3 DIAGNOSIS TROUBLESHOOTING STRATEGY...... 34-3 SYMPTOM CHART...................

More information

2000 Ranger Workshop Manual

2000 Ranger Workshop Manual SECTION 211-02: Power Steering 2000 Ranger Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/1/1999 Gear Torsion Bar Suspension Special Tool(s) Remover, Tie Rod End 211-001 (TOOL-3290-D)

More information

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT:

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT: 1953-1956 Ford Truck Coil-Spring Front End Tech Line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE PARTS LIST BELOW TO MAKE SURE YOUR

More information

AEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE

AEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE AEV30308AA Last Updated: 05/31/18 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND

More information

SUSPENSION 2-1 SUSPENSION CONTENTS

SUSPENSION 2-1 SUSPENSION CONTENTS TJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 5 page REAR SUSPENSION... 12 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION

More information

FRONT AXLE AND SUSPENSION FA 1

FRONT AXLE AND SUSPENSION FA 1 FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated

More information

Installing the Custom IFS

Installing the Custom IFS 35-40 Ford Car & 35-41 Ford Truck Chassis Custom IFS & 4-Link Install Instructions Tech Line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE

More information

TRANSMISSION REMOVAL & INSTALLATION - A/T

TRANSMISSION REMOVAL & INSTALLATION - A/T TRANSMISSION REMOVAL & INSTALLATION - A/T 1990 Nissan 240SX 1990 TRANSMISSION SERVICING Nissan Automatic Transmission Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX NOTE: For

More information

INSTALLATION INSTRUCTION 88094

INSTALLATION INSTRUCTION 88094 INSTALLATION INSTRUCTION 88094 FOR RANCHO SUSPENSION SYSTEM RS6594B 4WD & 2WD NISSAN TITAN READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev D IMPORTANT NOTES! WARNING:

More information

Installing the Custom IFS Installing the lower control arms:

Installing the Custom IFS Installing the lower control arms: 33-34 Ford Car & Truck Chassis Custom IFS & 4-Link Install Instructions Tech Line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE PARTS

More information

CHASSIS CONTENTS EXTERIOR PARTS 6-1 FRAME COVER 6-2 REAR FRAME COVER 6-4 FRONT WHEEL 6-6 FRONT BRAKE 6-10 HANDLEBARS 6-17 FRONT FORK 6-19

CHASSIS CONTENTS EXTERIOR PARTS 6-1 FRAME COVER 6-2 REAR FRAME COVER 6-4 FRONT WHEEL 6-6 FRONT BRAKE 6-10 HANDLEBARS 6-17 FRONT FORK 6-19 CHASSIS CONTENTS EXTERIOR PARTS 6- FRAME COVER 6- REAR FRAME COVER 6-4 FRONT WHEEL 6-6 FRONT BRAKE 6-0 HANDLEBARS 6-7 FRONT FORK 6-9 STEERING 6-6 REAR WHEEL 6-3 REAR BRAKE 6-39 6 REAR SHOCK ABSORBER 6-43

More information

CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT: TOTAL COST INVOLVED

CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT: TOTAL COST INVOLVED 333-TCIE237 1967-1969 Chevy Camaro Front End, 1968-1972 Chevy Nova Front End 1967-1969 Pontiac Firebird Front End Suspension Installation Instructions 1-855-693-1259 www.totalcostinvolved.com CHECK ALL

More information

REAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION REAR SUSPENSION DIAGNOSIS LOWER ARM AND TOE CONTROL ARM ASSEMBLY...

REAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION REAR SUSPENSION DIAGNOSIS LOWER ARM AND TOE CONTROL ARM ASSEMBLY... 34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION........... 34-2 DIAGNOSIS.... 34-2 INTRODUCTION....................... 34-2 TROUBLESHOOTING STRATEGY........ 34-2 SYMPTOM CHART..................... 34-3 SYMPTOM

More information

5. Refer to GTR Workshop Manual, section: and disconnect battery ground cable.

5. Refer to GTR Workshop Manual, section: and disconnect battery ground cable. HYDRAULIC HOSE REPAIR REMOVAL PROCEDURE 1. Open door. 2. Turn ignition 'ON'. 3. Power the convertible top to the fully lowered position. 4. Turn ignition 'OFF'. 5. Refer to GTR Workshop Manual, section:

More information

SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1

SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1 SUENSION SUENSION SYSTEM 1 Vehicle/pulls Bottoming Sway/pitches Wheel shimmy Abnormal tire wear SUENSION SYSTEM PROBLEM SYMPTOMS TABLE Use the table below to help determine the cause of the problem. The

More information

www.clubsuprafrance.com CLUTCH 1996 Toyota Supra 1995-96 Clutch Supra DESCRIPTION The single, dry-type disc clutch uses a hydraulicallyoperated master cylinder with a clutch release cylinder mounted on

More information

SCdefault. 900 Installation instructions

SCdefault. 900 Installation instructions SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part

More information

TECHNICAL BULLETIN S /00. S-TYPE Essential Tools Specifications SERVICE DATE 2000 MY-ON S-TYPE MODEL VIN L00001-ON

TECHNICAL BULLETIN S /00. S-TYPE Essential Tools Specifications SERVICE DATE 2000 MY-ON S-TYPE MODEL VIN L00001-ON SERVICE DATE 03/00 TECHNICAL BULLETIN S-TYPE Essential Tools Specifications MODEL VIN S100-01 2000 MY-ON S-TYPE L00001-ON Issue: The Service Tools required for the S-TYPE Sedan are listed below, which

More information

SECTION C FRONT SUSPENSION. Section Description Page C.1 REMOVING AND REFITTING A FRONT SUSPENSION UNIT 5

SECTION C FRONT SUSPENSION. Section Description Page C.1 REMOVING AND REFITTING A FRONT SUSPENSION UNIT 5 SECTION C FRONT SUSPENSION Section Description Page C.1 REMOVING AND REFITTING A FRONT SUSPENSION UNIT 5 C.2 REMOVING AND REFITTING THE COMPONENTS OF THE FRONT SUSPENSION 8 C.3 CHECKING AND OVERHAULING

More information

Notice: Refer to Adding Fluid to the Brake System Notice in the Preface section.

Notice: Refer to Adding Fluid to the Brake System Notice in the Preface section. Page 1 of 6 2008 Pontiac G8 G8 Service Manual Brakes Disc Brakes Repair Instructions Document ID: 2065646 Front Disc Brake Pads Replacement Removal Procedure Tools Required J 23738-A Hand Vacuum Pump.

More information

TECHNICAL BULLETIN. Rear Suspension Special Tools JD199 & JD199-1 Repair Procedure 64-15

TECHNICAL BULLETIN. Rear Suspension Special Tools JD199 & JD199-1 Repair Procedure 64-15 TECHNICAL BULLETIN Rear Suspension Special Tools JD199 & JD199-1 Repair Procedure 64-15 MODEL Sedan Range 1994 MY DATE 8/94 From: VIN 696459 ISSUE: New rear suspension design introduced on all Sedan Range

More information

Removing/installing final drive

Removing/installing final drive 1(16) Removing/installing final drive Special tools: 998 5972, 999 5561, 999 5652, 999 5659, 999 5660 Removing Note! Position the rear lifting arms on the arrows on the sills. This is so the support arm

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information

2003 Jaguar X-Type BRAKES' 'Disc - X-Type

2003 Jaguar X-Type BRAKES' 'Disc - X-Type REAR DISC BRAKE CALIPER WARNING: Brake dust, if inhaled can damage your health. Always remove brake dust using a vacuum brush. Do not use a compressed air line to disperse brake dust into the atmosphere.

More information

IRS-151 INSTALLATION INSTRUCTIONS `55-57 CHEVY INDEPENDENT REAR SUSPENSION

IRS-151 INSTALLATION INSTRUCTIONS `55-57 CHEVY INDEPENDENT REAR SUSPENSION IRS-151 INSTALLATION INSTRUCTIONS `55-57 CHEVY INDEPENDENT REAR SUSPENSION Please read these instructions completely before starting your installation. Remember the basic rule for a successful installation:

More information

INSTALLATION INSTRUCTION 88581

INSTALLATION INSTRUCTION 88581 INSTALLATION INSTRUCTION 88581 FOR RANCHO SUSPENSION SYSTEM RS6581B: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev D IMPORTANT NOTES! WARNING: This suspension

More information

SUSPENSION 2-1 SUSPENSION CONTENTS

SUSPENSION 2-1 SUSPENSION CONTENTS WJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 4 page REAR SUSPENSION... 15 ALIGNMENT INDEX page AND WHEEL ALIGNMENT... 1 SERVICE PROCEDURES PRE-ALIGNMENT... 2 AND WHEEL

More information

60-65 Falcon, Comet & Ranchero Coil Spring IFS

60-65 Falcon, Comet & Ranchero Coil Spring IFS 60-65 Falcon, 62-65 Comet & 62-65 Ranchero Coil Spring IFS All engine installations with this front end will require a rear sump oil pan. 289-302 Small Block Ford Motors Milodon rear sump pan holds 7 quarts

More information

SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1

SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1 SUENSION SUENSION SYSTEM 1 SUENSION SYSTEM Suspension system Vehicle is unstable Bottoming Sways/pitches Wheels shimmy Abnormal tire wear Vehice pull PROBLEM SYMPTOMS TABLE Use the table below to help

More information

Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles.

Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles. Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles. Now, apply some anti-seize to the threads of the pivot stud. Also put anti-seize inside the bore

More information

CYLINDER HEAD CONTINUED ON NEXT FRAME. Ref. Part No. Number Description Qty Remarks

CYLINDER HEAD CONTINUED ON NEXT FRAME. Ref. Part No. Number Description Qty Remarks A1 CYLINDER HEAD 1 4JY-11111-00-00 HEAD, CYLINDER 1 (4JY-11111-01-00).......... 1 2 90116-08394-00 BOLT, STUD.............. 5 3 90176-08026-00 NUT, CROWN............. 5 4 90201-08087-00 WASHER, PLATE...........

More information

SUBJECT: NO: Honk Or Squeal Noise During Parking Lot Maneuvers GROUP: Steering. DATE: Aug. 28, 1998

SUBJECT: NO: Honk Or Squeal Noise During Parking Lot Maneuvers GROUP: Steering. DATE: Aug. 28, 1998 SUBJECT: NO: 19-05-98 Honk Or Squeal Noise During Parking Lot Maneuvers GROUP: Steering DATE: Aug. 28, 1998 THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETINS 19-07-97, DATED MAY 9, 1997 AND 19-11-97,

More information

FRONT RACK, BODY PANEL, AND HEADLIGHT ASSEMBLIES

FRONT RACK, BODY PANEL, AND HEADLIGHT ASSEMBLIES FRONT RACK, BODY PANEL, AND HEADLIGHT ASSEMBLIES 0747-506 1 2506-107 1 Rack, Front - Assembly (inc. 2) 2 0411-576 1 Decal, Warning - Load 3 0441-592 4 Bushing 4 8410-835 4 Screw, Cap 5 0423-669 4 Spacer

More information

INSTRUCTION S G-Comp Front Suspension: Chevy Nova Speedway Motors, Inc. 2017

INSTRUCTION S G-Comp Front Suspension: Chevy Nova Speedway Motors, Inc. 2017 INSTRUCTION S 350-100 G-Comp Front Suspension: 62-67 Chevy Nova Speedway Motors, Inc. 2017 Kit Contents: 91035700 G-Comp Bare Subframe 350101 G-Comp Support Tubes 91035702 G-Comp Front Subframe Hardware

More information

ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT

ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.

More information

Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided.

Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Put the urethane bushings into the upper antiroll-bar-link eyebolt. Coat the bushings

More information

FRONT AXLE ASSEMBLY. DRW G No:T ISSUE No: 1

FRONT AXLE ASSEMBLY. DRW G No:T ISSUE No: 1 FRONT AXLE ASSEMBLY 7 5 7 0 9 9 5 7 5 5 9 7 0 7 0 9 DRW G No:T0090 ISSUE No: TRACTOR 9/ 9 K.5, K, KT, K5 & K FRONT AXLE PARTS LIST Bolt / UNF X / 0500 Spacer 7mm X / I.D. 0900 Washer / T HP 0000 Rose Joint

More information

GROUP 32 POWER PLANT MOUNT CONTENTS WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES

GROUP 32 POWER PLANT MOUNT CONTENTS WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES 32-1 GROUP 32 POWER PLANT MOUNT CONTENTS GENERAL DESCRIPTION......... 32-2 SPECIAL TOOL................. 32-3 ENGINE MOUNTING............. 32-3 REMOVAL AND INSTALLATION........ 32-3 INSPECTION.......................

More information

CYLINDER HEAD CONTINUED ON NEXT FRAME. Ref. Part No. Number Description Qty Remarks

CYLINDER HEAD CONTINUED ON NEXT FRAME. Ref. Part No. Number Description Qty Remarks A1 CYLINDER HEAD 1 4JY-11111-00-00 HEAD, CYLINDER 1 (4JY-11111-01-00).......... 1 2 90116-08394-00 BOLT, STUD.............. 5 3 90176-08026-00 NUT, CROWN............. 5 4 90201-08087-00 WASHER, PLATE...........

More information

GENESIS COUPE(BK) > 2010 > G 3.8 DOHC > Steering System

GENESIS COUPE(BK) > 2010 > G 3.8 DOHC > Steering System GENESIS COUPE(BK) > 2010 > G 3.8 DOHC > Steering System Steering System > General Information > Specifications Specifications Steering gear Oil pump Steering angle Power steering oil Item Specification

More information

TH!NK neighbor Section 2 Chassis Section 2 Chassis

TH!NK neighbor Section 2 Chassis Section 2 Chassis General Specifications... 2 Torque Specifications... 2 Description and Operation... 4 Wheel Alignment Angles... 4 Brakes... 4 Diagnosis and Testing... 6 Ball Joint Inspection... 6 Wheel Bearing Inspection...

More information

TOYOTA PRIUS PLUS LOWERING SPRINGS Preparation

TOYOTA PRIUS PLUS LOWERING SPRINGS Preparation Preparation Part Number: PTR07-47100 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 2 Nut 4 1 Instructions Hardware Bag Contents Item # Quantity Reqd. Description 1 2

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DRUM TO DISC BRAKE CONVERSION KIT A118 pre-1985 Ford F150 (except 1983-1984 w/super H/D axle) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.

More information

Illustrated Parts Manual

Illustrated Parts Manual 1 10 Illustrated Parts Manual 2 425 CR EFT Model Number A2011IRK4CETR (Red) S H A R E O U R PA S S IO N. TM TABLE OF CONTENTS 2011 ATV 425 CR EFT Red (A2011IRK4CETR) FRONT RACK, BODY PANEL, AND HEADLIGHT

More information

97-06 Jeep TJ Wrangler 2. 5 " & 4 " S u s p e n s i o n L i f t Installation Instructions

97-06 Jeep TJ Wrangler 2. 5  & 4  S u s p e n s i o n L i f t Installation Instructions 97-06 Jeep TJ Wrangler 2. 5 " & 4 " S u s p e n s i o n L i f t Installation Instructions Safety Glasses Metric / Standard Wrenches & Sockets Drill / Assorted Drill Bits Floor Jack Jack Stands Measuring

More information

Pro/Series 2000 Tubular A-Arm Front Suspension

Pro/Series 2000 Tubular A-Arm Front Suspension 11 Mennonite Church Road Spring City, PA 19475 (610) 948-7303 Installation Instructions Pro/Series 2000 Tubular A-Arm Front Suspension (Pinto-Style) CAUTION!!! The most important requirement for a successful

More information

AB65KVZS180 ITG Maxogen Airbox Kit Fitting Instructions

AB65KVZS180 ITG Maxogen Airbox Kit Fitting Instructions AB65KVZS180 ITG Maxogen Airbox Kit Fitting Instructions 1 AB65KVZS Performance Air Box Fitting Instructions: Rover 45 MG ZS180 (2.5 V6) PARTS LIST: QTY Description 1 X AB65C Carbon Air Box (with 6mm drain

More information

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT:

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT: 1947-1954 Chevy Truck Coil-Spring Front End Tech line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE PARTS LIST BELOW TO MAKE SURE YOUR

More information

400 2x4/4x4 EFT SHARE OUR PASSION ṬM

400 2x4/4x4 EFT SHARE OUR PASSION ṬM SHARE OUR PASSION ṬM 400 2x4/4x4 EFT Model Number A2009IDG2BETR (Red - 2x4) Model Number A2009IDG2BETZ (Cat Green - 2x4) Model Number A2009IDG4BETR (Red - 4x4) Model Number A2009IDG4BETG (Green - 4x4)

More information

400 4x4 Euro MODEL NUMBER A2008IDG4BEUR (RED) MODEL NUMBER A2008IDG4BEUG (GREEN) MODEL NUMBER A2008IDG4BEUZ (CAT GREEN) MORE TO GO ON.

400 4x4 Euro MODEL NUMBER A2008IDG4BEUR (RED) MODEL NUMBER A2008IDG4BEUG (GREEN) MODEL NUMBER A2008IDG4BEUZ (CAT GREEN) MORE TO GO ON. 2008 400 4x4 Euro Illustrated Parts Manual MODEL NUMBER A2008IDG4BEUR (RED) MODEL NUMBER A2008IDG4BEUG (GREEN) MODEL NUMBER A2008IDG4BEUZ (CAT GREEN) MORE TO GO ON. TM TABLE OF CONTENTS 2008 ATV 400 4x4

More information

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT:

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT: 1957-1964 Ford Truck Custom IFS Tech Line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE

More information

Cobra IRS Aluminum Differential Bushings (MMIRSB-40.2)

Cobra IRS Aluminum Differential Bushings (MMIRSB-40.2) 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com Cobra IRS Aluminum Differential Bushings (MMIRSB-40.2) The MM front differential

More information

POWER STEERING TO INDEX POWER STEERING SYSTEM PRECAUTIONS... OPERATION CHECK... PROBLEM SYMPTOMS TABLE... VANE PUMP ASSEMBLY COMPONENTS...

POWER STEERING TO INDEX POWER STEERING SYSTEM PRECAUTIONS... OPERATION CHECK... PROBLEM SYMPTOMS TABLE... VANE PUMP ASSEMBLY COMPONENTS... TO INDEX STEERING POWER STEERING POWER STEERING SYSTEM PRECAUTIONS.............................................. OPERATION CHECK......................................... PROBLEM SYMPTOMS TABLE.................................

More information

INSTALLATION INSTRUCTIONS `64 ½ - 70 MUSTANG, HEIDTS IFS, PRO-G GEN II P/N: MTF-201

INSTALLATION INSTRUCTIONS `64 ½ - 70 MUSTANG, HEIDTS IFS, PRO-G GEN II P/N: MTF-201 INSTALLATION INSTRUCTIONS `64 ½ - 70 MUSTANG, HEIDTS IFS, PRO-G GEN II P/N: MTF-201 Please read these instructions completely Before starting your installation. Assemble suspension on vehicle before powder-coating

More information