INSTALLATION INSTRUCTIONS
|
|
- May Logan
- 5 years ago
- Views:
Transcription
1 Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number ) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer) Harness 1 bag containing: Ford Emblem 1 bag containing 2 Tailgate emblem retainers 2 Mounting Screws 2 Foam pieces (if needed and optional) 1 bag containing: 25 Wire Ties (short) Z-Tech (in a white bottle) 1 bag containing: 3 Templates (along with these instructions) 2 Wire Ties (long and optional) Tools Required: T20 and T30 Torx Drivers 7mm, 8mm, and 10mm Sockets Flat Head Screwdriver Phillips Screwdriver Plastic Trim Removal tool Drill Bit and small Flat File 1 inch and 1¾ inch Center Hole Saws Soldering Iron Small brush Round file (if needed) Mirror removal tool # OTC8200 (Required for non-screw type mirrors) Deburring Tool PRE-INSTALLATION VEHICLE CHECKLIST Before beginning, determine how the vehicle is equipped and check appropriate boxes: Determine whether the vehicle has an opening in the center of pickup bed close to opposite of the opening in the bottom of the tailgate. Yes, skip Section 2. No, tailgate must be removed to drill an opening for the camera harness (refer to Section 2). Determine whether the vehicle has the required three mounting holes behind the existing tailgate emblem. Refer to Steps 1 & 2 to remove inner tailgate panel, and use supplied template to confirm whether the required holes are present in the panel. No, use supplied template to position the holes to drill and/or cut the tailgate. If you do not wish to cut the tailgate, Brandmotion offers tailgate handle camera kits ( , black handle and , chrome handle) that do not require cutting. Yes, proceed to Section 3. Vehicle does NOT have an auto dimming inside mirror (refer to Section 8). Determine the connector style used on the existing inside rearview mirror: 7-pin or 16-pin. For past models additional information, please see Section 11B (reference). Check kit contents are complete against the list above.
2 Section 1: Camera Mount Preparation 1. Lower tailgate and remove upper sheet metal cover by removing the eight screws with a T- 30 Torx bit (Figure 1). Figure 1 5. If camera mounting holes and harness opening were present in the existing tailgate, proceed to Step 8. If not, align the supplied template to the two existing emblem locating holes. 6. Mark and center punch the location for the two retaining clip holes and the camera and harness access opening (Figure 3). Figure 3 2. From the inside of the tailgate, verify whether two square mounting holes and a central opening approximately 1-3/4 inch in diameter are present behind the factory emblem. If not, it will be necessary to drill and square two holes for camera mount retainers and a cut an opening for the camera and harness (Steps 5-7). 3. Raise the tailgate. Taking care not to damage the body panel, insert plastic trim removal tool into the base of existing emblem to pry it off (Figure 2). Figure 2 7. Drill the two retaining clip holes with a 3/8- inch drill bit. Use a small flat file to square the drilled holes for the retaining clips (recommended method). Alternate method: Drill the two holes with a 1/8-inch drill bit and use sheet metal screws (not supplied in kit) to mount the camera harness. Apply Z-tech to drilled holes. 8. Insert retaining clips (Figure 4). Figure 4 4. Remove any adhesive remaining on the tailgate.
3 Section 1: Camera Mount Preparation continued 9. Drill a pilot hole for the camera mount. Using a 1¾ inch hole saw, cut the camera harness opening. Trial fit camera mount and file opening as necessary (Figure 5). Figure Apply Z-tech to camera harness opening.
4 Section 2: Cut Pickup Bed Opening Follow Steps 12 through 16 only if the vehicle does not have an opening in the bed above the license plate per Figure 6 Figure Center punch the mark and drill a pilot hole. Next, cut a 1 inch opening with a hole saw (Figure 8). Figure Remove tailgate retaining straps. With an assistant, remove the tailgate by lifting away from lower tension pins. Set tailgate aside. 13. Measure 21 inches from the left edge and 1¼ inches from the top and make a temporary mark on the pickup bed (Figure 7). Figure Clean the rough edges of the opening with a deburring tool. Apply supplied Z-tech with a small brush (Figure 9). Figure With the aid of an assistant, reinstall tailgate on tension pins and reattach straps.
5 Section 3: Camera Installation 17. Mounting Camera 17a. Remove material between camera opening and round hole for harness clearance (apply supplied Z-tech to any exposed bare metal with a small brush). Insert the two retainer clips (Figure 10). 18. Run camera harness through opening in the base of the tailgate and seat grommet in pickup bed (Figure 11). Figure 11 Figure 10 17b. Route the camera harness through tailgate opening (Figure 1O.5). 19. Using the two supplied 7mm screws, attach camera mount to tailgate. Press the supplied emblem into the camera mount. Figure 10.5
6 Section 4: Rain Sensor Modification (If equipped) Follow Steps 20 and 21 on this page only if you have a rain sensor module mounted on your inside rear view mirror. 20. Remove rain sensor by pulling down and remove connector (Figure 12). Figure Using a round file, open up the rain sensor opening for mirror by 0.46mm so the supplied mirror fits (Figure 13). Figure 13
7 Section 5: Mirror Removal 22. Start the vehicle and note location of compass display. Remove the connector from mirror (Figure 14). Figure 14 NOTE: On some models without screws, Mirror Removal Tool # OTC8200 is required. 23. If the compass display on the dash shows (- -) the compass module must be relocated. This operation is described in Section Loosen the screw that attaches the existing rear view mirror to the windshield mounting button with a T20 Torx driver (Figure 15). CAUTION: Removing the mirror from the windshield can cause damage to the windshield. It is highly recommended to contact either a Ford dealership or a windshield replacement company. Otherwise, slide the mirror upwards and towards the rear to remove it from the windshield (Figure 15). Figure 15
8 Section 6: Interior Harness Installation 25. Remove driver side dash panel end cap by pulling away weather-stripping and pull end panel to release clips from the dash panel (Figure 16). Figure Remove both sun visor anchors (either side of roof console) by removing one screw with a Phillips screw driver (Figure 18). Figure Remove driver side A-pillar by pulling with hands to release clips from sheet metal (Figure 17). Figure Remove roof console with hands to remove the clips from the sheet metal. Then remove both connectors (Figure 19). Figure 19
9 Section 6: Interior Harness Installation continued 29. Route the supplied interior harness under leading edge of the driver side headliner by gently separating the headliner from the windshield and tucking the harness into the gap with your fingers (Figure 20). 31. Route the supplied interior harness through the dash (Figure 22). Figure 22 Figure Route the supplied interior harness down the driver side A-pillar (Figure 21). Figure 21
10 Section 7A: Removing the Compass Circuit Board (if required) Follow the steps in section 7A only if your compass displayed - - when the mirror connector was removed in Section Pry mirror apart with a screwdriver (Figure 23). Figure 25 Figure Remove the circuit board from the mirror by disengaging both connectors. Mark the top of the circuit board with a permanent marker to insure proper plug connection later (Figure 24). Figure Make sure ignition is off. Remove the original vehicle mirror harness connector by cutting the harness wires 2 inches from the connector. Cut wires one at a time and strip the insulation from each as these will be spliced to the supplied interior harness. 34. Wrap the mirror circuit board in the supplied foam pieces, and cut an opening for the connector terminals (Figure 25).
11 Section 7B: Wiring for vehicles with 7-pin mirror connector 36. On the supplied interior harness, near the black 10 pin connector, locate the seven loose wires. Using Connector C911 pinout diagram opposite, splice these wires to the vehicle mirror harness wires where the mirror connector was removed in step 35 as follows: Splice the supplied interior harness black ground wire to the loose vehicle mirror ground wire that was in pin 3. Splice the supplied interior harness green reverse wire to the loose vehicle mirror reverse wire that was in pin 2. Splice the supplied interior harness pink ignition wire to the loose vehicle mirror ignition wire that was in pin 1. Splice the supplied interior harness red compass (+) to the loose vehicle mirror compass (+) wire that was in pin 6. Splice the supplied interior harness yellow compass (-) to the loose vehicle mirror compass (-) wire that was in pin 7. Tape up the orange wire. Tape up the white wire. 37. If you removed the compass circuit board, per section 7A, on the supplied interior harness, near the white 6 pin connector, locate the five loose wires. Using Connector C911 pinout diagram opposite, splice these five wires to the vehicle mirror harness connector removed in step 35 as follows: Splice the supplied interior harness black ground wire to the vehicle mirror connector ground wire. (pin 3) Splice the supplied interior harness green reverse wire to the vehicle mirror connector reverse wire. (pin 2) Splice the supplied interior harness pink ignition wire to the vehicle mirror connector ignition wire. (pin 1) Splice the supplied interior harness red compass (+) wire to the vehicle mirror connector compass (+) wire. (pin 6) Splice the supplied interior harness yellow compass (-) wire to the vehicle mirror connector wire. (pin 7) If you did not remove the compass circuit board, isolate the five loose wires with electrical tape, as they will not be used. NOTE: If reverse signal does not exist in pin 2 of 7- pin mirror C911 connector (see diagram below), then follow directions in Section 8 to connect reverse. NOTE: Circuit colors shown may vary depending on model and year. Verify pin locations and check circuit for proper function using a digital volt-ohm meter.
12 Section 7C: Wiring for vehicles with 16-pin connector 38. On the supplied interior harness, near the black 10 pin connector, locate the seven loose wires (Note: Isolate the red wire with electrical tape as it will not be used). Using Connector C9039 pinout diagram opposite, splice the remaining six wires to the vehicle mirror harness wires where the mirror connector was removed in step 35 as follows: Splice the supplied interior harness black ground wire to the loose vehicle mirror ground wire that was in pin 4. Splice the supplied interior harness green reverse wire to the loose vehicle mirror reverse wire that was in pin 9. Splice the supplied interior harness pink ignition wire to the loose vehicle mirror ignition wire that was in pin 1. If populated, splice the supplied interior harness yellow wire to the loose vehicle mirror wire was in pin 2. Tape up the orange wire. Tape up the white wire. 39. If you removed the compass circuit board, per section 7A, on the supplied interior harness, near the white 6 pin connector, locate the five short wires. (Note: Isolate the red wire with electrical tape as it will not be used). Using Connector C9039 pinout diagram opposite, splice the remaining four wires to the vehicle mirror harness connector removed in Step 35 as follows: Splice the supplied interior harness black ground wire to the vehicle mirror connector ground wire. (pin 4). Splice the supplied interior harness green reverse wire to the vehicle mirror connector reverse wire. (pin 9). Splice the supplied interior harness pink ignition wire to the vehicle mirror connector ignition wire. (pin 1) NOTE: If reverse signal does not exist in Pin 9 of 16- pin mirror C9039 connector (see diagram opposite), then follow directions in Section 8 to connect reverse. NOTE: Circuit colors shown may vary depending on model and year. Verify pin locations and check circuit for proper function using a digital volt-ohm meter. If populated, splice the supplied interior harness yellow wire to the vehicle mirror connector wire that supplies pin 2. If you did not remove the compass circuit board, isolate the five loose wires with electrical tape, as they will not be used.
13 Section 7D: Relocating the Compass Circuit Board (if required) Follow the steps in section 7D only if your compass displayed - - when the mirror connector was removed in Section Solder all connections and cover with heat shrink tubing or electrical tape. 41. Plug connector into mirror circuit board. Maintain the original connector orientation: retaining tab to top side of board (Figure 26). Figure 28 Figure Route the mirror circuit board connector as shown. (Figure 29). Figure Remove driver s side knee bolster trim by removing three screws with a M7 socket. Pull panel by hand to release mounting clips (Figure 27). Figure Remove the driver s side knee bolster reinforcement by removing the four M8 screws (Figure 28).
14 Section 7D: Relocating the Compass Circuit Board continued (if required) Follow the steps in section 7D only if your compass displayed - - when the mirror connector was removed in Section Place the mirror circuit board as shown (connector facing forward and towards the bottom). Secure the circuit board to the existing cross dash harness with the two supplied long wire ties (Figure 30). Figure 30
15 Section 8: Inside Rear View Mirrors without Auto Dimming (if required) Follow the steps in section 8 only if the vehicle does not have an auto dimming inside rear view mirror. 46. Remove the passenger side door sill plate with a trim tool and remove passenger side kick panel with hands, just disengaging the two clips from the sheet metal (Figure 31). Figure 31 vehicle model. Solder and cover the connection with tape or heat shrink tubing. 50. Attach the black ground wire eyelet from the supplied interior harness white 6-pin connector end to sheet metal in the passenger side kick panel with a screw using an 8mm socket (Figure 32). Figure Isolate the seven wires near the black 16-pin mirror connector on the supplied interior harness with electrical tape along with the red and yellow wires near the white 6-pin connector. 48. Route the supplied interior harness green, pink, and black wires along the vehicle cross dash harness as shown in figure 32. Secure using wire ties wherever possible at 2 inch intervals. 49. Splice the green reverse wire from the supplied interior harness white 6-pin connector end to the wire listed in Diagram A, on the next page, depending on the 51. Splice the pink ignition wire from the supplied interior harness white 6-pin connector end to the wire listed in Diagram A, on the next page, depending on the vehicle model. Solder and cover the connection with tape or heat shrink tubing.
16 Section 8: Inside Rear View Mirrors without Auto Dimming continued (if required) Non Auto Dimming Pinouts Diagram A Chassis Harness Ignition & Reverse Locations Model Year(s) Function Connector F150 Super Duty 2012 (late production) 2012 (late production) Dia. Page Ignition C2280B 18 Reverse C2280D 19 Ignition C2280B 20 Reverse C2280D 19 NOTE: For previous years pinouts, please refer to Section 11C. Supplied Interior Harness Location Pin Color Color Right Kick (BCM) Right Kick (BCM) Right Kick (BCM) Right Kick (BCM) 35 Violet/Green Pink 13 Blue/White Green 35 Violet/Green(Gas) Yellow/Orange (Diesel) Pink 13 Blue/White Green
17 Section 8: Inside Rear View Mirrors without Auto Dimming continued (if required) INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM B Ignition Connector C2280B 2012 late production F150
18 Section 8: Inside Rear View Mirrors without Auto Dimming continued (if required) INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM C Reverse Connector C2280D 2012 late production F150 and Super Duty
19 Section 8: Inside Rear View Mirrors without Auto Dimming continued (if required) INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM D Ignition Connector C2280B 2012 late production Super Duty
20 Section 9: Supplied Mirror Installation 52. Plug the 10-pin connector from the supplied interior harness into the supplied mirror (Figure 33). Figure Install the supplied mirror on the mounting button and slide it downwards. Secure by tightening the T20 Torx screw to 1.8 Nm (16 lb-in.), while not exceeding 2.2 Nm (19.5 lb-in.). 54. If equipped, reinstall modified Rain Sensor from Section 4.
21 Section 10: Chassis Harness Installation 55. Remove the driver side sill plate with a trim tool (Figure 34). Figure 36 Figure Loosen driver side A-pillar molding with hands and then remove the driver side lower kick panel (Figure 35). Figure Secure Super Duty template number (Figure 37) or secure F150 template number over opening in front of driver s seat (Figure 38). Figure 37 Figure Pull back carpet in front of driver s seat (Figure 36).
22 Section 10: Chassis Harness Installation continued 59. Center punch and drill a pilot hole then drill a 1 inch hole with a hole saw. 60. Clean the hole with a deburring tool (Figure 39). Figure 39 Figure Route the supplied chassis harness toward the supplied interior harness and connect together (Figure 42). 61. Apply supplied Z-tech with a small brush (Figure 40) Figure 40 Figure Route the supplied chassis harness through the drilled opening and seat the grommet from the inside of vehicle (Figure 41).
23 Section 10: Chassis Harness Installation continued 64. Route the exterior portion of the supplied chassis harness along existing vehicle chassis harness and over fuel tank. Using supplied tie wraps, secure the harness to existing wiring at 2 inch intervals (Figures 43 and 44). Figure 45 Figure Plug the chassis harness into the camera harness installed earlier under the pickup bed (Figure 46). Figure 46 Figure Loop any excess from the harness as shown and secure with tie wraps (Figure 45). 67. Start vehicle with foot on brake and shift into reverse to check camera operation. If all of the connections are correct, you will see an image displayed on the left side of the supplied mirror. 68. Reinstall all previously removed interior and exterior parts.
24 Section 11A: Reference Supplied Harness Pinouts 6-pin connector pinouts PIN # FUNCTION CAMERA HARNESS COLOR CHASSIS HARNESS COLOR INTERIOR HARNESS COLOR 1 Video (+) White White Gray/Dark Blue 2 Shield Blue Blue White 3 Reverse Green Green Green 4 Video (-) Brown Brown Gray/Orange 5 Ground Black Black Black 6 Ignition Red Red Pink Loose wires provided in the Supplied Interior Harness Function Wire color Ground (-) Black Reverse signal 12V Green Ignition 12V Pink Compass (+) Red Compass (-) Yellow Auto dimming (+) Orange Auto dimming (-) White Section 11B: Reference - Previous Model Year Mirror Connector Pinouts
25 Supplied Interior Harness Color 1 Pink 2 Green 3 Black Red 10 Yellow Microphone Supplied Harness Color 1 Blue (+) 2 3 Black Yellow Black Supplied Interior Harness Color 1 Pink Black Green Orange (+) White (-) 16
26 Section 11B: Reference - Previous Model Year Mirror Connector Pinouts continued F150 Pinout
27 Section 11C: Reference - Previous Model Year Ignition & Reverse Locations Model Year Function Connector F F150 F (early production) Supplied Interior Harness Dia. Page Location Pin Color Color Ignition C270J 29 Right Kick 2 Reverse C270E 30 Right Kick 20 Ignition C270J 29 Right Kick 2 Reverse C270B 31 Right Kick 12 Ignition C2280D 32 Right Kick 16 White / L. Blue Black / Pink White / L. Blue Green/ Yellow Blue or Blue/ Red Pink Green Pink Green Pink Reverse C Right Kick 6 Blue Green Super Duty Super Duty (early production) Ignition C Right Kick SJB 10 Reverse C Right Kick SJB 12 Red / Yellow Black / Pink Pink Green Ignition C Right Kick 2 Blue Pink Reverse C Right Kick 10 Green/ Blue Green
28 Section 11C: Reference Previous Model Year Ignition & Reverse Locations continued Ignition Connector C270J F150
29 Section 11C: Reference Previous Model Year Ignition & Reverse Locations continued Reverse Connector C270E 2004 F150
30 Section 11C: Reference Previous Model Year Ignition & Reverse Locations continued Reverse Connector C270B F150
31 Section 11C: Reference Previous Model Year Ignition & Reverse Locations continued Ignition Connector C2280D (early production) F150
32 Section 11C: Reference Previous Model Year Ignition & Reverse Locations continued Reverse Connector C (early production) F150
33 Section 11C: Reference Previous Model Year Ignition & Reverse Locations continued Ignition and Reverse Connector C Super Duty
34 Section 11C: Reference Previous Model Year Ignition & Reverse Locations continued Ignition and Reverse Connector C (early production) Super Duty
35 Section 11D: Reference Relocating the Compass Circuit Board for vehicles with External Compass Module (if required) 69. Remove the separate compass module from the existing interior mirror by sliding it downwards (Figure 47). Figure Pry the compass apart with a screwdriver (Figure 49). Figure Remove connector from the compass module (Figure 48). Figure Remove the circuit board from the compass module (Figure 50). Figure 50
36 Section 11D: Reference Relocating the Compass Circuit Board for vehicles with External Compass Module continued (if required) 73. Wrap the circuit board in the supplied foam and cut an opening for connector terminal (Figure 51). Figure 53 Figure Plug the compass module connector into the circuit board (Figure 52) Figure Install the compass module circuit board between underneath the headliner as shown. The connector should face up, to the rear, and to the right (Figure 53).
37 Section 11E: Reference Vehicles with Sync Microphone in Mirror Follow the steps on this page only for auto dimming inside rear view mirror with built in Sync microphone. 74. Splice the supplied interior harness to the vehicle mirror harness by following the next ten steps and Diagram E. Note: Isolate the black, green and pink wires at the white 6 pin connector end of the supplied interior harness with electrical tape as they will not be used. Splice the black ground wire from the supplied interior harness black 16 pin connector end to the wire in pin 10 of the vehicle mirror harness connector. Splice the green reverse wire from the supplied interior harness black 16 pin connector end to the wire in pin 3 of the vehicle mirror harness connector. Splice the pink ignition wire from the supplied interior harness black 16 pin connector end to the wire in pin 1 of the vehicle mirror harness connector. Splice the red positive (+) compass wire from the supplied interior harness black 16 pin connector end to the wire in pin 6 of the vehicle mirror harness connector. Splice the yellow negative (-) compass wire from the supplied interior harness black 16 pin connector end to the wire in pin 2 of the vehicle mirror harness connector. Splice the yellow open wire from the microphone harness (supplied separately) to the wire in pin 4 of the vehicle mirror harness connector. Splice the black ground wire from the microphone harness (supplied separately) to the wires in pins 5 and 10 of the vehicle mirror harness connector. Splice the blue 12V positive (+) wire from the microphone harness (supplied separately) to the wire in pin 1 of the vehicle mirror harness. Cover all connections with electrical tape or heat shrink. 75. Place the microphone in a convenient place on A-pillar or in headliner. Auto Dimming With Built In Sync Microphone Mirror Pinout DIAGRAM E Supplied Interior Harness Wire Color 1 Pink 2 Yellow 3 Green Red 7 White - 8 Orange Black Microphone Supplied Harness Wire Color 1 Blue Yellow - 5 Black Black
38 Rear Vision System Liftgate Emblem Camera Mirror Display Ford Flex (Kit part number ) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer) Harness 2 Foam pieces (if needed and optional) 1 bag containing: Ford Emblem 1 bag containing: 2 Liftgate emblem retainers 2 Mounting Screws 1 bag containing: 25 Wire Ties (short) Z-Tech (in a white bottle) 1 bag containing: 1 Template (along with these instructions) 2 Wire Ties (long and optional) Tools Required: T15, T20, and T30 Torx Drivers 5.5mm, 7mm, 8mm, and 10mm Sockets Flat Head Screwdriver Phillips Screwdriver Plastic Trim Removal tool Pliers Razor Knife or scissors Wire Cutters Soldering Iron Small Brush Additional Tools: Drill Bit 1¾ inch Center Hole Saw Flat Metal File Round File or Deburring Tool Mirror Removal Tool # OTC8200 PRE-INSTALLATION VEHICLE CHECKLIST Before beginning, determine how the vehicle is equipped and check appropriate boxes: Determine whether the vehicle has the required two mounting holes and a camera harness opening behind the existing liftgate emblem. Refer to Steps 2-4 to remove inner liftgate panel, and use supplied template to confirm whether the required holes are present in the panel. No, use supplied template to position the holes to drill and/or cut the liftgate. Yes, proceed to Section 2. Vehicle has Sync microphone built into the rear view mirror (refer to Section 7). To retain Sync function, Brandmotion Kit #5000-PESMVR external microphone must be installed. Vehicle does NOT have an auto dimming inside mirror (refer to Section 8). Determine the connector style used on the existing inside rearview mirror: 7-pin or 10-pin. For additional information, please see Section 6. Determine the existing inside rearview mirror retention method: T20 Torx screw or clip style. If clip style, the Mirror Removal Tool # OTC8200 similar specialty tool, is required. For additional information, see Section 4. Check kit contents are complete against the list above.
39 Section 1: Camera Mount Preparation 1. Remove grommets from the supplied chassis harness and camera harness. Remove tape and, taking care not to cut the supplied wiring, cut grommets off with a razor knife, scissors, or wire cutters (Figure 1). Discard grommets. Figure 3 Figure 1 4. Remove upper liftgate trim and set aside. 2. Raise liftgate. Using a plastic trim removal tool, pry off the two red plastic reflectors in the lower edge of the liftgate to expose four retaining screws (Figure 2). Figure 2 5. If equipped with power liftgate opener, remove the top end of the power gas strut by prying off the bolt cover with a plastic trim tool to access one 10mm bolt. Use a 10mm socket to remove and push free end of strut aside. 6. From the inside of the liftgate, verify whether two square mounting holes and a central camera pass through opening are present behind the factory emblem. If not, it will be necessary to drill and square two holes for camera mount retainers and a cut an opening for the camera and harness (Steps 10 & 11). 7. Close the liftgate. Taking care not to damage the body panel, insert plastic trim removal tool into the base of existing emblem to pry it off (Figure 4). Figure 4 3. Unfasten the four screws with a Phillips screwdriver and pry up on the edges of the liftgate lower trim panel to release it from the liftgate. Remove liftgate lower trim panel and set aside (Figure 3).
40 Section 1: Camera Mount Preparation continued 8. Remove any adhesive remaining on the liftgate. 9. If two camera mounting holes and a camera harness opening were present in the existing liftgate, proceed to Section 2. If not, align the supplied template to the two existing emblem locating holes and camera harness opening. 13. Mark, center punch, and drill a pilot hole for the camera mount harness opening (Figure 7). Using a 1¾ inch hole saw, cut the camera harness opening. Trial fit camera mount and file opening as necessary. Figure Mark and center punch the location for the two retaining clip holes (Figure 5). Figure Clean the rough edges of the opening with a round file or deburring tool. 11. Drill the two retaining clip holes with a 3/8- inch drill bit. Use a small flat file to square the drilled holes for the retaining clips (recommended method). Alternate method: Drill the two holes with a 1/8-inch drill bit and use sheet metal screws (not supplied in kit) to secure the camera mount. 12. Apply supplied Z-tech to exposed bare metal with a small brush, and insert supplied retaining clips (Figure 6). Figure 6
41 Section 2: Camera Installation 15. Test fit the camera mount in the factory tailgate opening. If the camera mount does not fit flush, determine where the mount is contacting the edges of the opening and use a flat metal file to enlarge it. Work slowly, checking often for fit. 16. Clean the rough edges of the enlarged opening with a deburring tool or round file. 18. Route the camera harness through liftgate opening. 19. Using the two supplied 7mm screws, attach camera mount to liftgate (Figure 9). Figure Apply supplied Z-tech to any exposed bare metal with a small brush (Figure 8). Figure Route the light gray connector end of the camera harness along the inner liftgate structure toward the driver side of the liftgate opening.
42 Section 3: Chassis Harness Installation 21. Using a plastic trim removal tool, loosen two access covers in the D-pillar trim panel to expose two 7mm bolts (Figure 10) Figure Run the small black connector end of the chassis harness through the opening you cut in the grommet and out through the other open end of the grommet. A pair of pliers may be required to pull the connector and harness through the opening (Figure 12). Figure Remove the two bolts with a 7mm socket, and loosen the driver side upper D-pillar trim panel by peeling back weather stripping slightly and releasing the retaining clips (Figure 11). Figure Route the light gray chassis harness camera connector end of the chassis harness toward the light gray connector on the camera harness and connect (Figure 13). Figure If necessary, use a razor knife to cut a small slit in the liftgate wiring grommet to assist in the routing of the chassis harness wiring trough the grommet.
43 Section 3: Chassis Harness Installation continued 26. Pull down rear edge of headliner slightly to route chassis harness inside and towards the driver side D-pillar. 27. Remove driver side C-pillar trim panel with a trim removal tool (Figure 14). Figure Partially unclip driver side lower quarter panel trim. 29. Route chassis harness forward taking care not to bind the cable when replacing the trim. 30. Remove the driver side rear door sill plate with a trim tool. 31. Loosen driver side rear door weather strip. 32. Remove 5.5mm screw and loosen driver side lower C-pillar trim. 33. Loosen driver side lower B-pillar trim panel with hands. 34. Continue routing chassis harness forward, taking care not to pinch wiring between trim pieces. 35. Remove the driver side front door sill plate with a trim tool. 36. Route remainder of chassis harness towards dash.
44 Section 4: Mirror Removal 37. Start the vehicle and note location of compass display. Remove the connector from the inside rearview mirror (Figure 15). Figure 15 Figure 17 Mirror Removal Tool # OTC If the compass display on the dash shows (- -) the compass module must be relocated. This operation is described in Section Verify mirror mount retention method. If the vehicle mirror is retained with a screw, use a T20 Torx driver to remove the screw that attaches the existing rear view mirror to the windshield (Figure 16). Figure 16 CAUTION: Removing the mirror from can cause damage to the windshield. It is highly recommended to contact either a Ford dealership or an automotive glass replacement company to perform this task. 41. Slide the mirror upward to remove and set aside. 40. If the vehicle mirror is retained with a clip, use Mirror Removal Tool # OTC8200 Ford dealers to release the mirror (Figure 17).
45 Section 5: Interior Harness Installation 42. Remove driver side dash panel end cap by pulling away weather-stripping. Pry end panel to release clips from the dash panel. 43. Remove both sun visor anchors (either side of roof console) by removing two bolts with a T15 socket. 46. Route the supplied interior harness down the driver side A-pillar (Figure 19). Figure Loosen driver side A-pillar molding with hands and then remove the driver side lower kick panel. 45. Loosen headliner at top of windshield with hands to remove the clips from the sheet metal. Then route supplied interior harness towards mirror mount (Figure 18). Figure 18
46 Section 6A: Removing the Compass Circuit Board (if required) Follow the steps in Section 6A only if your compass displayed - - when the mirror connector was removed in Section Pry mirror apart with a screwdriver (Figure 20). Figure 20 Figure Remove the circuit board from the mirror by disengaging both connectors. Mark the top of the circuit board with a permanent marker to insure proper plug connection later (Figure 21). 50. Make sure ignition is off. Remove the original vehicle mirror harness connector by cutting the harness wires 2 inches from the connector. Cut wires one at a time and strip the insulation from each as these will be spliced to the supplied interior harness. Figure Wrap the mirror circuit board in the supplied foam pieces, and cut an opening for the connector terminals (Figure 22).
47 Section 6B: Compass Wiring for Vehicles with 7-pin Mirror Connector 51. On the supplied interior harness, near the black 10 pin connector, locate the seven loose wires. Isolate and tape over the loose orange and white wires on the interior harness as they will not be used. Using Connector C911 pinout diagram opposite, splice the remaining five wires to the vehicle mirror harness wires where the mirror connector was removed in Section 4 as follows: Splice the supplied interior harness black ground wire to the loose vehicle mirror ground wire that was in pin 3. Splice the supplied interior harness green reverse wire to the loose vehicle mirror reverse wire that was in pin 2. Splice the supplied interior harness pink ignition wire to the loose vehicle mirror ignition wire that was in pin 1. Splice the supplied interior harness red compass (+) to the loose vehicle mirror compass (+) wire that was in pin 6. Splice the supplied interior harness yellow compass (-) to the loose vehicle mirror compass (-) wire that was in pin 7. Splice the supplied interior harness black ground wire to the vehicle mirror connector ground wire. (pin 3) Splice the supplied interior harness green reverse wire to the vehicle mirror connector reverse wire. (pin 2) Splice the supplied interior harness pink ignition wire to the vehicle mirror connector ignition wire. (pin 1) Splice the supplied interior harness red compass (+) wire to the vehicle mirror connector compass (+) wire. (pin 6) Splice the supplied interior harness yellow compass (-) wire to the vehicle mirror connector wire. (pin 7) If you did not remove the compass circuit board, isolate the five loose wires with electrical tape, as they will not be used. NOTE: If reverse signal does not exist in pin 2 of 7- pin mirror C911 connector (see diagram below), follow directions in Section 8 to connect reverse. 52. If you removed the compass circuit board, per section 6A, on the supplied interior harness, near the black 6 pin connector, locate the five loose wires. Using Connector C911 pinout diagram opposite, splice these five wires to the vehicle mirror harness connector removed in Section 4 as follows: Supplied Interior Supplied Interior Harness Color Harness Color Pink Pink Green Green Black Black Red (+) Red (+) Yellow (-) Yellow (-) NOTE: Circuit colors shown may vary depending on model and year. Verify pin locations and check circuit for proper function using a digital volt-ohm meter.
48 Section 6C: Compass Wiring for Vehicles with 10-pin Mirror Connector 53. On the supplied interior harness, near the black 10 pin connector, locate the seven loose wires. Isolate and tape over the loose orange and white wires as they will not be used. Using Connector C925 pinout diagram opposite, splice the remaining six wires to the vehicle mirror harness wires where the mirror connector was removed in Section 4 as follows: Splice the supplied interior harness black ground wire to the loose vehicle mirror ground wire that was in pin 10. Splice the supplied interior harness green reverse wire to the loose vehicle mirror reverse wire that was in pin 3. Splice the supplied interior harness pink ignition wire to the loose vehicle mirror ignition wire that was in pin 1. Splice the supplied interior harness red compass (+) to the loose vehicle mirror compass (+) wire that was in pin 6. If populated, splice the supplied interior harness yellow compass (-) to the loose vehicle mirror compass (-) wire that was in pin If you removed the compass circuit board, per section 6A, on the supplied interior harness, near the black 6 pin connector, locate the five short wires. Using Connector C925 pinout diagram opposite, splice the remaining four wires to the vehicle mirror harness connector removed in Section 4 as follows: Splice the supplied interior harness black ground wire to the vehicle mirror connector ground wire. (pin 10). Splice the supplied interior harness green reverse wire to the vehicle mirror connector reverse wire. (pin 3). Splice the supplied interior harness pink ignition wire to the vehicle mirror connector ignition wire. (pin 1) Splice the supplied interior harness yellow compass (-) wire to the vehicle mirror connector compass (-) wire. (pin 2). Splice the supplied interior harness red compass (+) wire to the vehicle mirror connector compass (+) wire. (pin 6). If you did not remove the compass circuit board, isolate the five loose wires with electrical tape, as they will not be used. NOTE: If reverse signal does not exist in Pin 3 of 10- pin mirror C925 connector (see diagram below), then follow directions in Section 8 to connect reverse. C925 NOTE: Circuit colors shown may vary depending on model and year. Verify pin locations and check circuit for proper function using a digital volt-ohm meter. Supplied Interior Harness Color Pink Pink (12V + + Ignition Yellow (-) (-) Green Green Red Red (+) (+) Black
49 Section 6D: Relocating the Compass Circuit Board (if required) Follow the steps in section 6D only if your compass displayed - - when the mirror connector was removed in Section Solder all connections and cover with heat shrink tubing or electrical tape. Plug connector into mirror circuit board. Maintain the original connector orientation: retaining tab to top side of board (Figure 23). Figure Make certain the mirror circuit board is orientated in the same direction it was installed in the mirror: connector facing forward and towards the bottom. This verification is required for the compass to read correctly. 59. Secure the circuit board to the existing cross dash harness with the two supplied long wire ties. 56. Remove driver side knee bolster trim by removing three screws with a 7mm socket. Pull panel by hand to release mounting clips. 57. Place the mirror circuit board connector under the dash as shown (Figure 24). Figure 24
50 Section 7: Replacing the Sync Microphone (if required) Follow the steps on this page only for inside rear view mirrors with built-in Sync microphone. To retain mic function, Brandmotion Kit #5000-PESMVR must be installed. 60. Splice the supplied microphone harness to the vehicle mirror harness by following the next ten steps and referring to Diagram E on the next page. Note: Isolate the black, green and pink wires at the black 6 pin connector end of the supplied interior harness with electrical tape as they will not be used. Splice the black ground wire from the supplied interior harness black 10 pin connector end to the wire in pin 10 of the vehicle mirror harness connector. Splice the green reverse wire from the supplied interior harness black 10 pin connector end to the wire in pin 3 of the vehicle mirror harness connector. Splice the pink ignition wire from the supplied interior harness black 10 pin connector end to the wire in pin 1 of the vehicle mirror harness connector. Tape up the orange wire. Tape up the white wire. Splice the red positive (+) compass wire from the supplied interior harness black 10 pin connector end to the wire in pin 6 of the vehicle mirror harness connector. Splice the yellow negative (-) compass wire from the supplied interior harness black 10 pin connector end to the wire in pin 2 of the vehicle mirror harness connector. Splice the yellow open wire from the microphone harness (supplied separately) to the wire in pin 4 of the vehicle mirror harness connector. Splice the black ground wire from the microphone harness (supplied separately) to the wires in pins 5 and 10 of the vehicle mirror harness connector. Splice the blue 12V positive (+) wire from the microphone harness (supplied separately) to the wire in pin 1 of the vehicle mirror harness. 61. Cover all connections with electrical tape or heat shrink. 62. Place the microphone in a convenient place on A-pillar or in headliner.
51 Section 7: Replacing the Sync Microphone continued (if required) Auto Dimming With Built In Sync Microphone Mirror Pinout DIAGRAM E Supplied Interior Harness Wire Color 1 Pink 2 Yellow 3 Green Red 7 White - 8 Orange Black Microphone Supplied Harness Wire Color 1 Blue Yellow - 5 Black Black
52 Section 8: Ignition, Reverse and Ground Locations Vehicles with Inside Rear View Mirrors without Auto Dimming (if required) Follow these steps only if vehicle does not have an auto dimming inside rear view mirror. 61. Remove the driver side door sill plate with a trim tool, just disengaging the two clips from the sheet metal and remove driver side kick panel. 62. Isolate the seven wires near the black 10-pin mirror connector on the supplied interior harness with electrical tape along with the red and yellow wires near the black 6-pin connector. 63. Route the supplied interior harness green, pink, and black wires along the vehicle dash harness. Secure using wire ties wherever possible at 2 inch intervals. 64. Splice the green reverse wire from the supplied interior harness black 6-pin connector end to the wire listed below. Cover the connection with tape or heat shrink tubing. 65. Attach the black ground wire eyelet from the supplied interior harness black 6-pin connector end to sheet metal in the driver side kick panel with a screw using an 8mm socket. 66. Splice the pink ignition wire from the supplied interior harness black 6-pin connector end to the wire color listed below. Solder and cover the connection with tape or heat shrink tubing. Reverse Lamp Relay Location Connector C Ford Flex Pin Circuit Function Supplied Interior Harness Color 8 Relay Reverse Lamps Green 12 Ground A Pillar Left Black 13 Fuse 41 or Circuit Breaker Pink (12V + Ignition) 24 Ground Pillar A Left Black
53 Section 9: Supplied Mirror Installation 67. Plug the 16-pin connector from the supplied interior harness into the supplied mirror (Figure 25). Figure Install the supplied mirror on the mounting button and slide it downwards. Secure by tightening the T20 Torx screw to 1.8 Nm (16 lbin.), while not exceeding 2.2 Nm (19.5 lb-in.). 69. Start vehicle with foot on brake and shift into reverse to check camera operation. If all the connections are correct, you will see an image displayed on the left side of the supplied mirror. 70. Use supplied wire ties approximately every two inches to secure camera harness to existing vehicle wiring inside the liftgate. 71. Secure any other loose harness wiring using supplied wire tires. 72. Reinstall all previously removed interior and exterior parts. 73. Press the supplied emblem into the liftgate camera mount.
54 Section 10: Reference Supplied Harness Pinouts PIN # FUNCTION 6-pin connector pinouts CAMERA HARNESS COLOR CHASSIS HARNESS COLOR INTERIOR HARNESS COLOR 1 Video (+) White White Gray/Dark Blue 2 Shield Blue Blue White 3 Reverse Green Green Green 4 Video (-) Brown Brown Gray/Orange 5 Ground Black Black Black 6 Ignition Red Red Pink Loose wires provided in the Supplied Wire Harness Function Wire color Ground (-) Black Reverse signal 12V Green Ignition 12V Pink Compass (+) Red Compass (-) Yellow Auto dimming (+) Orange Auto dimming (-) White
55 Front Template number (F-150)
56 CameraHousingClearanceTemplate (ForVehicleswithExistingHoles) Top AlignWithExistingHoles RemoveMaterialforHarness Clearance AlignWithExistingHoles InsertSuppliedScrewRetainer InsertSuppliedScrewRetainer CameraHousingCut-OutTemplate (ForVehicleswithNoHoles) Top AlignWithExistingHoles 1/2 Dril ThenFileToFit 3/8 Dril ThenFileSquare ToFitRetainerClip AlignWithExistingHoles 3/8 Dril ThenFileSquare ToFitRetainerClip 13/4 Dril CameraClearance HoleThenFileToFit
INSTALLATION INSTRUCTIONS
Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationRear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number )
Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Mirror Display 2004 onwards Ford F-150 and 2008 onwards Ford Super Duty (Kit part numbers 1008-9520 and 1008-9525) Kit Contents: RVS Interior (shorter) Harness RVS Chassis (longer) Harness
More informationRear Vision System Liftgate Emblem Camera for Aftermarket Display Ford Flex (Kit part number )
Rear Vision System Liftgate Emblem Camera for Aftermarket Display 2009-2012 Ford Flex (Kit part number 1008-6509) Kit Contents: Liftgate Emblem Mount with Camera Chassis Harness with RCA (Note: In some
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Rear Vision System Mirror Display 2013-Current Ram (Kit part number 1009-9518) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Rear
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Mirror Display Dodge Ram Kit Contents: Instruction Sheets Template Chassis Harness Endgate Handle with Camera Wire Ties (Qty: 17) Bottle of ZTech Plug for Non-Locking Endgates (Optional)
More informationINSTALLATION INSTRUCTIONS. Rear Vision System Mirror Display 2010 onwards Camaro (Kit part number )
Rear Vision System Mirror Display 2010 onwards Camaro (Kit part number 1018-9540) Kit Contents: RVS Interior (shorter) harness RVS Chassis (longer) harness Camera with mounting bracket Mirror 1 bag containing:
More informationINSTALLATION INSTRUCTIONS
OEM Recessed Lip Camera with Harness and Slimline Mirror (Kit part number 9002-8724) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the
More informationINSTALLATION INSTRUCTIONS
Rear Vision System NAV Display 2009-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9501) Kit Contents: Camera/Module/Bezel Assembly Chassis Harness NAV Harness 1
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:
More informationINSTALLATION INSTRUCTIONS. Rear Vision System Aftermarket Display 2009-Current Dodge Ram (Kit part number )
Rear Vision System Aftermarket Display 2009-Current Dodge Ram (Kit part number 1009-6503) Kit Contents: Chassis Harness with RCA Endgate Handle with Camera 1 bag containing: Wire Ties (Qty: 17) Bottle
More informationOEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 16-pin Mirror Connector (Kit part number )
OEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 16-pin Mirror Connector (Kit part number 9002-8722) Please read thoroughly before starting installation and check that kit contents
More informationINSTALLATION INSTRUCTIONS
OEM Tailgate Camera/Bezel Assembly with Chassis Harness 2014-current Chevrolet Silverado and GMC Sierra (Kit part number 9002-1005) Kit Contents: Chassis Harness 1 bubble bag containing: Tailgate Handle
More informationINSTALLATION INSTRUCTIONS. Rear Vision System Aftermarket Display 2009-Current Dodge Ram (Kit part number )
Rear Vision System Aftermarket Display 2009-Current Dodge Ram (Kit part number 1009-6503) Kit Contents: Chassis Harness with RCA (Note: In some cases a RCA extension may be required to connect to your
More informationINSTALLATION INSTRUCTIONS
9002-6513 Rear Vision System W/ Zoom Aftermarket and Factory 8.4 Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 2012 RAM (Part B) 2013 Current RAM (Part A) NOTE:
More informationINSTALLATION INSTRUCTIONS
OEM Lip Mount Camera with Harness and OnStar Mirror for GM Vehicles with 10-pin Mirror Connector (Kit part number 9002-8723) Items Included in the Kit: Bubble bag containing: Camera with Mount Mirror Mirror
More informationINSTALLATION INSTRUCTIONS
OEM Recessed Lip Camera with Harness and Auto Dimming Mirror (Kit part number 9002-8721) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket Display 2007-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9560) Kit Contents: Chassis Harness with RCA (Note: In some cases a RCA
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket Display 2007-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9560) Kit Contents: Camera/Module/Bezel Assembly Chassis Harness with
More informationINSTALLATION INSTRUCTIONS
OEM Recessed Lip Camera with Harness and OnStar Mirror for GM Vehicles with 10-pin Mirror Connector (Kit part number 9002-8722) Please read thoroughly before starting installation and check that kit contents
More informationINSTALLATION INSTRUCTIONS
Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # 9002-8838) Items Included in the Kit Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts These Instructions Required Tools & Supplies
More informationINSTALLATION INSTRUCTIONS
360º Vision System for Aftermarket Radio/Display (Kit # AVMS-3690) DUE TO THE COMPLEXITY OF THIS KIT PROFESSIONAL INSTALLATION IS REQUIRED CALIBRATION KIT IS REQUIRED FOR FINAL PROGRAMMING Please read
More informationJeep Wrangler Rear Vision Camera, 2007 Current (Kit # )
Items Included in the Kit Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts These Instructions 22--pin white connector w/ video RCA (for factory display radio) Jeep Wrangler Rear Vision
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Versa (2012) PART NUMBER: 999F3 AW008 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Infiniti JX (2013) PART NUMBER: 999F3 YY000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationREARSIGHT PART NUMBER: Code: MC1 RECOMMENDED SEQUENCE OF APPLICATION
Document # 3848 REVISION A 1/26/06 2006 TOYOTA TACOMA REARSIGHT PART NUMBER: 00016-00050 Code: MC1 RE V I S I O N A KIT CONTENTS ITEM QTY DESCRIPTION 1 1 MIRROR/MONITOR 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
Important: Read Before Installation *550-0022-000* 550-0022AAA Dealer Installation Recommended. To avoid serious personal injury or property damage, obtain the Installation Instructions before attempting
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Versa Note 999F3 4Z000 - Accent Lighting Kit. 999Q9 AY000 - Accessory Service Connector
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror with Compass and Homelink 2. APPLICATION: Juke (2011) 3. PART NUMBER: 999L1 VW002 4. KIT CONTENTS: Item Qty Description Service
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Pathfinder 999F3 XZ000 - Accent Lighting Kit. Item QTY Description Service Part
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)
More informationTOYOTA FJ CRUISER AIR DAM/LIGHT BAR Preparation
Preparation Part Number: PT278-35071 Kit Contents Item # Quantity Reqd. Description 1 1 Air Dam / Light Bar Hardware Bag 1 Contents Item # Quantity Reqd. Description 1 2 Screw, M6x33mm, Wafer Head 2 2
More informationTOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT413-42130 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 20 Cable Tie 2 2 Scotchlok 3 2 Foam Pad
More informationJeep Wrangler Rear Vision Camera, 2007 Current (Kit # )
Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # 9002-8837) Items Included in the Kit Required Tools & Supplies Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts Program Module 22--pin
More information* * APPLICABLE MODELS: 2016 > CX-3
PART NUMBER: 0000 8C S01(DIO) / 0000 89 S07(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0688-000* APPLICABLE MODELS: 2016 > CX-3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More information* * APPLICABLE MODELS: 2014 > Mazda 3
PART NUMBER: 0000 8C L48 (DIO) / 0000 89 L84 (PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0700-000* APPLICABLE MODELS: 2014 > Mazda 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage
More informationGENUINE ACCESSORIES INSTALLATION INSTRUCTIONS. ITEM QTY DESCRIPTION Usage Chart Service Part Number. 1 1 Mirror Assembly w/ Compass 1
AUTO PART NUMBER: 0000 8C P4 (DIO)/ 0000 89 P25 (PIO) REQUIRED COMPONENTS: INSTALLATION KIT: 2 SA Harness - 2 Conductor 3 0 Wire Ties 4 Wire Cover 5 A-Pillar Tether Clip (D09W-6862) 6 3 Foam Tape 7 3 Electro-Tap(wire
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. REAR VIEW CAMERA ATTACHMENT PILOT AII 23620 Issue Date MAY 2002 PARTS LIST Attachment Kit : P/N 08B21-S9V-100 Control unit harness Rear
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More informationIT IS IMPORTANT THAT YOU OBTAIN THE CORRECT INFORMATION FOR YOUR VEHICLE, OR DAMAGE TO THE WIRING SYSTEM COULD OCCUR.
Instructions for Universal Harness PRINT THESE INSTUCTIONS Gentex Mirror Installation Instructions Provided by www.rearviewautomirrors.com These instructions have been prepared to provide you with details
More informationJeep Wrangler Adjustable Rear Vision Camera, 2007 Current (Kit # )
Items Included in the Kit Jeep Wrangler Adjustable Rear Vision Camera, 2007 Current (Kit # 9002-8848) Camera Chassis Harness Power Harness 22--pin white connector w/ video RCA (for factory display radio)
More information* * APPLICABLE MODELS: 2014 > Mazda 6
PART NUMBER: 0000 8C H02(DIO) / 0000 89 H18(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0694-000* APPLICABLE MODELS: 2014 > Mazda 6 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage
More information* * APPLICABLE MODELS: 2017 > CX-5
PART NUMBER: 0000 8C R06(DIO) / 0000 89 R28(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0681-000* APPLICABLE MODELS: 2017 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ATTACHMENT (EX-L WITH NAVI) 2008 RIDGELINE AII 36587 Issue Date MAY 2007 PARTS LIST Attachment Kit P/N: 08B21-SJC-102 Template Rear camera
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationINSTALLATION INSTRUCTIONS
Backup Camera Interface (Kit # 9002-7762) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Cam T-Harness Plug & Play I/O T-Harness
More informationLEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationTOYOTA tc HANDS FREE BLU LOGIC Preparation
TOYOTA tc 2011- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Coupe and Sedan (2011+) PART NUMBER: 999F4 AX008 - Universal Security Lighting Kit. KIT CONTENTS:
More informationTOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationJeep Wrangler Adjustable Infrared Light Rear Vision Camera System for Factory Display Radios 2007 Current (Kit # )
Jeep Wrangler Adjustable Infrared Light Rear Vision Camera System for Factory Display Radios 2007 Current (Kit # 9002-8857) Items Included in the Kit Required Tools & Supplies Camera Chassis Harness Power
More informationGentex Homelink Installation Instructions
Gentex Homelink Installation Instructions Kit Contents: Item Qty Part Description 1 Number GENK-41 NVS Homelink Mirror GENK-42 NVS Homelink w/mood lights 1 of the GENK-45 NVS Homelink w/compass following
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Contents Description: Auto-Dimming Rearview Mirror with Compass Part Number: 990B0-35007 Applications: SX4 Hatchback, 2007- SX4 Sedan, 2008- Installation Time:.5 HRS Ref. Part
More informationConflicts NOTE: XLE, LE, AND SE MODELS
TOYOTA SIENNA 2011- REARSIGHT Part Number: 00016-00085 Accessory Code: MC9 Conflicts NOTE: XLE, LE, AND SE MODELS KIT CONTENTS ITEM QTY DESCRIPTION 1 1 MIRROR/MONITOR 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA
More informationIR Temp Probe. Toyota Sienna Rear Sight. Part Number: Accessory Code:MC1
Toyota Sienna 200 - Rear Sight Part Number: 0006-00085 Accessory Code:MC Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 2 3 4 5 6 7 8 MIRROR/MONITOR REVERSE MINI-CAMERA
More informationTOYOTA TACOMA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-35052 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 1 T-tap Connectors,
More informationPart Number: PT
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationConflicts. TOYOTA 4Runner REARSIGHT. Part Number: Code: MC90 KIT CONTENTS ADDITIONAL ITEMS REQUIRED FOR INSTALL RECOMMENDED TOOLS
TOYOTA 4Runner 2010 - REARSIGHT Part Number: 00016-00085 Code: MC90 Conflicts KIT CONTENTS ITEM QTY DESCRIPTION 1 1 MIRROR/MONITOR 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA EXTENSION HARNESS 4 1 SACK PARTS 5
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Sedan (2013+) PART NUMBER: 999F4 AX010 - Universal Security Lighting Kit. KIT CONTENTS: Item QTY
More informationGeneral Applicability: KIA Sorento. Issues Current Kit does not allow for CAN DATA remote access
Document #730135 Created ACH 08/02/2018 Revised ACH 08/20/18 A2 General Applicability: 2018-19 KIA Sorento Issues Current Kit does not allow for CAN DATA remote access Kit Contents: Item# Component Description
More informationSCION xb EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationTOYOTA SIENNA TRAILER WIRE HARNESS Preparation
Preparation Part Number: PT791-08150 (non-se) PT791-08102 (SE only) Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Module Harness 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting
More informationTOYOTA AVALON EC REARVIEW MIRROR
Section I - Installation Preparation Part Number: PT732-07000 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Full Mirror Assembly, Compass 2 1 Hardware Bag 3 1
More informationTOYOTA COROLLA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationSCION xb AUTO-DIMMING MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationDVD REAR SEAT VIDEO SYSTEM
Read entire instructions thoroughly before starting. TOOLS REQUIRED: DVD REAR SEAT VIDEO SYSTEM MINIVANS WITH ROOF RAILS INSTALLATION INSTRUCTIONS Non-metal trim stick Phillips screwdriver T15, T20, T25
More informationTOYOTA HIGHLANDE R REARSIGHT Part Number: Code: MC90 KIT CONTENTS ADDITIONAL ITEMS REQUIRED FOR INSTALL RECOMMENDED TOOLS
TOYOTA HIGHLANDE R 2009- REARSIGHT Part Number: 00016-00085 Code: MC90 KIT CONTENTS ITEM QTY DESCRIPTION 1 1 MIRROR/MONITOR 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA EXTENSION HARNESS 4 1 SACK PARTS 5 1 OWNER
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2010 ODYSSEY Publications No. AII 41818 Issue Date JUNE 2009 PARTS LIST Right center sensor clip (Black) Backup Sensor Attachment Kit P/N 08V67-SHJ-101C
More informationINSTALLATION INSTRUCTIONS. Jeep Wrangler Adjustable Rear Vision System for Factory Display Radios, 2007 Current (Kit # )
Jeep Wrangler Adjustable Rear Vision System for Factory Display Radios, 2007 Current (Kit # 9002-8847) Items Included in the Kit Camera Chassis Harness Power Harness 22--pin white connector w/ video RCA
More informationSCION xd INTERIOR LIGHTING UPGRADE Preparation
Preparation Part Number: PTS21-52085 Light Guide Kit Contents Item # Quantity Reqd. Description 1 1 Controller Board, 4 color programmed w/ Bracket 2 1 RGB, LED Engine wire harness 3 2 14mm Light Rod,
More informationCERTAIN TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE
PAGE 1 OF 19 CERTAIN 2015-2017 TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE OVERVIEW In the affected vehicles, it may be possible for water to pool and
More informationREARVIEW MIRROR AND BACKUP CAMERA KIT
REARVIEW MIRROR AND BACKUP CAMERA KIT P/N 2881483 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationLEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated
More informationScion xd EC Rearview Mirror Preparation
Scion xd 2010 - EC Rearview Mirror Preparation Part Number: 00016-09101 Code: CM9 Kit Contents Item # Quantity Reqd. Description 1 1 Mirror Assembly w/ Compass and Homelink 2 1 Hardware bag Hardware Bag
More informationTOYOTA CAMRY EC REARVIEW MIRROR Preparation
TOYOTA CAMRY 2010 - EC REARVIEW MIRROR Preparation Part Number: 00016-09101 Code: CM9 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ Compass 2 1 Hardware bag Hardware Bag Contents
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2004 S2000 AII 26323-31611 Issue Date DEC 2005 PARTS LIST Rear defroster switch Hardtop 3-Pin subharness (If equipped, not used) 4-Pin subharness
More informationINSTALLATION INSTRUCTIONS
Ultrasonic Rear Park Aid Kit (Kit # 9002-3000) INSTALLATION INSTRUCTIONS Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: 4 Ultrasonic
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: R42H (2011) PART NUMBER: 999F3 AW000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description Service
More informationTOYOTA TACOMA HANDS FREE BLU LOGIC Preparation. Item 5 Item 6 Item 7 Item 8. Item 4. General Applicability Note: Recommended Tools
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00098 Conflicts: JBL Audio, Factory Navigation Kit Contents: NOTE: Part number of this accessory may not be the same as the part number
More informationInstallation Instructions (Auto Dimming/Comp/Temp Video Display Mirror)
9002-9516 Installation Instructions (Auto Dimming/Comp/Temp Video Display Mirror) IMPORTANT: Read before installing. Mirror Mounting - This mirror has a Wedge/ D-tab style mounting base. Please check our
More informationTOYOTA RAV TRAILER WIRE HARNESS Preparation
Preparation Part Number: PU322-42013-UW Kit Contents Item # Qty Description 1 1 Trailer Module Harness 2 1 Trailer 4-Flat Harness 3 1 Trailer Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24
More informationSCION xa AUTO-DIMMING MIRROR Preparation
Preparation Part Number: PT374-52040 (Compass) PT374-21050 (Homelink) Kit Contents Item # Quantity Reqd. Description 1a 1 AD Mirror Assembly w/compass & Map Lights (P/N PT374-52040) 1b 1 AD Mirror Assembly
More information2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill 1-3/4" Hole saw 2" Hole saw
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill
More informationToyota 4RUNNER With/MR Overhead Video
Toyota 4RUNNER With/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit-00110-14, Beige 00016-00120; Fit Kit-00120-14, Gray Accessory Code: ED7 Conflicts: Vehicles without a sunroof Kit Contents:
More informationRECOMMENDED SEQUENCE OF APPLICATION
2007-2008 TOYOTA TUNDRA CAMERA KIT PART NUMBER: 250-8045 KIT CONTENTS ITEM QTY DESCRIPTION 1 1 CAMERA ASSEMBLY 2 1 TRUCK EXTENSION HARNESS 3 1 TAILGATE EXTENSION HARNESS 4 1 POWER HARNESS 5 1 HARDWARE
More information(1) Remote Control with (2) AAA Batteries
TOOLS REQUIRED: KIT CONTENTS: E14 Torx (1) Remote Control with (2) AAA Batteries (2) Wireless Headphones with (4) AAA Batteries (2) DVD Headrest Units Owner s Manual (1) Owner s Manual (1) Power / Audio
More informationGeneral Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools
TOYOTA HIGHLANDER/HIGHLANDER HV 2008- Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationLGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions
LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and
More informationINSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1 DESCRIPTION: Trailer Tow Harness 2 APPLICATION: Nissan Rogue 3 PART NUMBER: 999T8 G2000 4 KIT CONTENTS: 999T8 G2000 Item Qty. Part Description Service Part Number
More informationINSTALLATION INSTRUCTIONS Accessory ACCESSORY HANDSFREELINK Application 2010 CR-V Publications No. AII 42587 Issue Date AUG 2009 PARTS LIST HFL Attachment Kit P/N 08E02-SWA-130 (Ivory) P/N 08E02-SWA-170
More informationInstallation of Auto Meter Cobalt Boost/Vacuum Gauge:
Installation of Auto Meter Cobalt Boost/Vacuum Gauge: Fitment: All 79-14 models. This installation was completed on a 2004 Mustang GT, and should be identical for all 1999-2004 model Mustangs. Time needed:
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER(S) REQUIRED FOR INSTALLATION: Dual Rear Seat USB Charge Port Kit Titan T99Q7 6LB0A (Excluding Single Ca T98Q7 5ZW2A (Metal
More informationLGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions
LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationINSTALLATION INSTRUCTIONS
Ultrasonic Rear Park Aid Kit (Kit # 9002-3000) INSTALLATION INSTRUCTIONS Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: 4 Ultrasonic
More information