Conflicts TOYOTA TACOMA HANDS FREE BLU TOOTH. Part Number: Accessory Code: BT4 ADDITIONAL ITEMS REQUIRED FOR INSTALL

Size: px

Start display at page:

Download "Conflicts TOYOTA TACOMA HANDS FREE BLU TOOTH. Part Number: Accessory Code: BT4 ADDITIONAL ITEMS REQUIRED FOR INSTALL"

Clifford Boyd
5 years ago
Views:

TOYOTA TACOMA 2011 - HANDS FREE BLU TOOTH Part Number: 00016-00401 Accessory Code: BT4 Conflicts Factory Bluetooth System & JBL Audio KIT CONTENTS ITEM QTY DESCRIPTION 1 1 INTERFACE MODULE 2 1

DESCRIPTION 1 N/A ELECTRICAL TAPE 2 3 4 GENERAL APPLICABILITY ALL MODELS RECOMMENDED SEQUENCE OF APPLICATION 1.

1 TOYOTA TACOMA HANDS FREE BLU TOOTH Part Number: Accessory Code: BT4 Conflicts Factory Bluetooth System & JBL Audio KIT CONTENTS ITEM QTY DESCRIPTION 1 1 INTERFACE MODULE 2 1 INTERFACE RADIO/POWER HARNESS 3 1 SYSTEM SWITCH 4 1 MICROPHONE PACK 5 1 HARDWARE BAG 6 2 FOAM ADHESIVE STRIP 7 1 QUICK GUIDE STICKER 8 1 OWNER S MANUAL ADDITIONAL ITEMS REQUIRED FOR INSTALL ITEM QTY DESCRIPTION 1 N/A ELECTRICAL TAPE GENERAL APPLICABILITY ALL MODELS RECOMMENDED SEQUENCE OF APPLICATION 1. All Applications Requiring Removal of A Pillar Completed Before Installation of Microphone. * MANDATORY HARDWARE BAG CONTENTS ITEM QTY DESCRIPTION 1 12 WIRE TIES 2 1 ADHESIVE FOAM PAD RECOMMENDED TOOLS SAFETY TOOLS SPECIAL TOOLS INSTALLATION TOOLS FASTENER REMOVAL TOOL TRIM REMOVAL TOOL 8 & 10-MM DEEP SOCKET POWER DRILL/DRIVER WIRE CUTTERS NEEDLE NOSE PLIERS SPECIAL CHEMICALS Southeast Toyota Distributors, LLC Page 1 of 6

PARTS IDENTIFICATION ITEM QTY DESCRIPTION PART NUMBER 1 1 INTERFACE MODULE 00016-00401-1 2 1 INTERFACE HARNESS 00016-00401-2 3 1 SYSTEM SWITCH 00016-00401-3 4 1 MICROPHONE PACK INCL.

2 PARTS IDENTIFICATION ITEM QTY DESCRIPTION PART NUMBER 1 1 INTERFACE MODULE INTERFACE HARNESS SYSTEM SWITCH MICROPHONE PACK INCL. IN ITEM HARDWARE BAG INCL. IN ITEM FOAM ADHESIVE STRIP INCL. IN ITEM QUICK GUIDE STICKER INCL. IN ITEM OWNER S MANUAL INCL. IN ITEM Southeast Toyota Distributors, LLC Page 2 of 6

VEHICLE PREPARATION CAUTION: IT IS ADVISABLE TO DISCONNECT THE NEGATIVE BATTERY CABLE FOR 3 MINUTES BEFORE BEGINNING INSTALLATION, TO AVOID UNINTENDED AIR BAG DEPLOYMENT.

USING A SCREWDRIVER, DISENGAGE THE 4 CLIPS AND REMOVE THE AIR CONDITIONER CONTROL ASSEMBLY. TAPE UP THE SCREWDRIVER TIP BEFORE USE. DISCONNECT THE 2 CONNECTORS.

FIGURE 2-3 NOTE: BE CAREFUL NOT TO PUT EXCESSIVE TENSION ON THE RADIO CONNECTIONS WHEN PULLING OUT THE RADIO.

3 VEHICLE PREPARATION CAUTION: IT IS ADVISABLE TO DISCONNECT THE NEGATIVE BATTERY CABLE FOR 3 MINUTES BEFORE BEGINNING INSTALLATION, TO AVOID UNINTENDED AIR BAG DEPLOYMENT. NOTE AND RECORD ANY ANTI- THEFT RADIO CODES PRIOR TO DISCONNECTING. VEHICLE PREPARATION 1. USING A SCREWDRIVER, DISENGAGE THE 4 CLIPS AND REMOVE THE AIR CONDITIONER CONTROL ASSEMBLY. TAPE UP THE SCREWDRIVER TIP BEFORE USE. DISCONNECT THE 2 CONNECTORS. FIGURE 1 FIGURE 1 2. REMOVE THE (4) 10MM BOLTS. DISCONNECT THE CONNEC- TOR AND REMOVE THE RADIO RECEIVER ASSEMBLY WITH BRACKET. FIGURE 2-3 NOTE: BE CAREFUL NOT TO PUT EXCESSIVE TENSION ON THE RADIO CONNECTIONS WHEN PULLING OUT THE RADIO. SUPPORT THE RADIO ASSEMBLY ON A PROTECT- ED SURFACE TO PREVENT ANY DAMAGE TO THE CONNECTIONS OR THE DASH PANELS. FIGURE 2 3. REMOVE TWO PUSH PINS ON THE TOP OF THE INSTRUMENT CLUSTER BEZEL. DISENGAGE BEZEL AND PULL OUT TOWARDS THE STEERING WHEEL. REMOVE THE INSTRU- MENT CLUSTER AS SHOWN IN FIGURE 5 BY REMOVING THE 10MM BOLTS. Southeast Toyota Distributors, LLC Page 3 of 6

THE FACTORY WIRE LOOM BEHIND THE INSTRUMENT CLUSTER AS FIGURE 5.

CONNECT THE RADIO/POWER INTERFACE HARNESS TO THE MODULE. FIGURE 8 2.

4 INSTALLATION INTERFACE MODULE 1. INSTALL THE AND SYSTEM SWITCH HANDS FREE INTERFACE MODULE MOUNT MODULE HERE TO THE FACTORY WIRE LOOM BEHIND THE INSTRUMENT CLUSTER AS FIGURE 5. SECURE SHOWN IN IT WITH WIRE TIES. CONNECT THE RADIO/POWER INTERFACE HARNESS TO THE MODULE. FIGURE 8 2. REMOVE THE CENTER SWITCH BLANK KNOCKOUT IN THE CENTER CONSOLE BETWEEN THE CIGARETTE LIGHTER AND POWER OUTLET. INSERT THE HANDS FREE SWITCH 12V WITH THE SOLID ARROW FACING UP INTO THE PANEL AS SHOWN IN FIGURE 7. ROUTE THE SWITCH HARNESS TO THE INTERFACE MODULE AND CONNECT. BUNDLE EXCESS WIRE TO THE FACTORY WIRE LOOM. USE A PIECE OF THE SUPPLIED FOAM TAPE TO COVER THE FUSE ON THE MAIN HARNESS. FIGURE 8-9 SWITCH MICROPHONE FIGURE 5 RADIO/PWR FIGURE 6 FIGURE 8 FIGURE 7 FIGURE 9 Southeast Toyota Distributors, LLC Page 4 of 6

INSTALLATION MICROPHONE 1. REMOVE THE TWO 10MM BOLTS HOLDING THE DRIVER S ASSIST HANDLE TO THE A-PILLAR.

ROUTE THE MICROPHONE HARNESS ALONG THE FACTORY WIRING AND USE WIRE TIES TO SECURE IT AS SHOWN IN FIGURE 10. NOTE: TAKE CARE NOT TO SECURE THE HAR- NESS TO THE AIRBAG OR ANY OF ITS COMPONENTS. 3.

CONNECT THE MICROPHONE HARNESS TO THE INTERFACE MODULE AS SHOWN IN FIGURE 8. FIGURE 10 4. REPLACE THE A-PILLAR PANEL.

CONNECT THE MAIN INTERFACE POWER HARNESS CONNEC- TORS TO THE FACTORY WIRE LOOM AND THE RADIO BY MATCH- ING THE CONNECTORS. MAKE SURE ALL CONNECTIONS ARE SECURELY SEATED.

5 INSTALLATION MICROPHONE 1. REMOVE THE TWO 10MM BOLTS HOLDING THE DRIVER S ASSIST HANDLE TO THE A-PILLAR. REMOVE THE LEFT A-PIL- LAR BY PULLING IT WAY FROM THE CHASSIS (DISENGAGING THE CLIPS) FIGURE ROUTE THE MICROPHONE HARNESS ALONG THE FACTORY WIRING AND USE WIRE TIES TO SECURE IT AS SHOWN IN FIGURE 10. NOTE: TAKE CARE NOT TO SECURE THE HAR- NESS TO THE AIRBAG OR ANY OF ITS COMPONENTS. 3. ROUTE THE MICROPHONE HARNESS BEHIND THE DASH AND INSTRUMENT CLUSTER OPENING TO THE INTERFACE MODULE, SECURING IT WITH WIRE TIES AND FOAM TAPE TO THE FACTORY WIRE LOOM. CONNECT THE MICROPHONE HARNESS TO THE INTERFACE MODULE AS SHOWN IN FIGURE 8. FIGURE REPLACE THE A-PILLAR PANEL. PRIOR TO FULLY SEATING THE CLIPS, CLEAN THE UPPER CORNER WITH THE SUPPLIED ALCOHOL PAD AND MOUNT THE MICROPHONE AS SHOWN IN FIGURE 11. RADIO AND REASSEMBLY FIGURE CONNECT THE MAIN INTERFACE POWER HARNESS CONNEC- TORS TO THE FACTORY WIRE LOOM AND THE RADIO BY MATCH- ING THE CONNECTORS. MAKE SURE ALL CONNECTIONS ARE SECURELY SEATED. NOTE: AVC-LAN (12-PIN) CONNECTOR MAY NOT BE PRESENT ON THE VEHICLE S HARNESS. WIRE TIE THIS CONNECTOR TO THE HARNESS UNCONNECTED, BUT ALWAYS CONNECT THE AVC-LAN (12-PIN) CONNECTOR INTO THE RADIO. IF AVC-LAN (12-PIN) CONNECTOR IS PRESENT INTHE VEHICLE HARNESS, CONNECT TO THE MAIN INTERFACE POWER HARNESS. IF ANY OTHER ACCESSORIES ARE INSTALLED THAT CONNECT TO THE HEAD UNIT, THE HANDS FREE SYSTEM SHOULD BE THE ACCESSORY THAT PLUGS INTO THE RADIO FIRST. 2. REINSTALL ALL TRIM PANELS IN THE ORDER OF REMOVAL, TAKING SPECIAL CARE TO MAKE SURE ALL HARNESSES AND WIRING ARE PROPERLY SECURED. MAKE SURE HARNESSES ARE NOT PINCHED OR BOUND BY TRIM PIECES. PLACE THE OWNER S MANUAL AND QUICK GUIDE STICKER IN THE GLOVE BOX. FIGURE RECONNECT NEGATIVE BATTERY CABLE AND TORQUE TO 3 FT LBS. RE-ENTER ANY THEFT DETERRENT INFORMATION, IF APPLICABLE. Southeast Toyota Distributors, LLC Page 5 of 6

6 TOYOTA TACOMA HANDS FREE BLU TOOTH Southeast Toyota Distributors, LLC Page 6 of 6

RECOMMENDED SEQUENCE OF APPLICATION

RECOMMENDED SEQUENCE OF APPLICATION TOYOTA TACOMA 2010- PART NUMBER: 250-8403 REARSIGHT KIT CONTENTS ITEM QTY DESCRIPTION 1 1 INTERFACE ADAPTER HARNESS 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA INTERFACE HARNESS 4 1 SACK PARTS COLOR APPLICABILITY/TRIM