INSTALLATION INSTRUCTIONS

Transcription

1 INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL ENGINE STARTER Application 2010 CR-V Publications No. AII Issue Date OCT 2009 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-101B Transmitter Accessory User s Information Manual Quick Start Guide Control unit Remote Control Engine Starter Attachment Kit (With vehicle security) P/N 08E92-SWA-100B Engine starter harness Antenna Control unit bracket Key ring Template Protective tape Fuse label Bracket Caution label 3 Relays 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 08E92-SWA-1B of 28

2 19 Wire ties Hood switch harness 2 Wire ties with clip Hood lock Clip Control unit bracket 11 Urethane tapes Template 6 x 12 mm Washer bolt Bracket 6 mm Flange nut 2 Self-tapping screws, 5 x 12 mm 3 Relays Remote Control Engine Starter Attachment Kit (Without vehicle security) P/N 08E92-SWA-100C Engine starter harness 26 Wire ties 2 Wire ties with clip 2 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

3 Clip Cable clip 11 Urethane tapes 6 x 12 mm Washer bolt 6 mm Flange nut TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Diagonal cutters Ratchet 8 mm and 10 mm Sockets 10 mm wrench Plastic trim tool (T/N SILTRIMTL10) Felt-tip pen Isopropyl alcohol Scissors Small flat-tip screwdriver Shop towel Scale Rubber mallet HDS (Honda Diagnostic System) Fender cover Needle nose pliers Tape 10 mm Combination wrench 2 Self-tapping screws, 5 x 12 mm 2 Spacers 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 3 of 28

4 Illustration of the Remote Control Engine Starter Installed on the Vehicle INSTALLATION With vehicle security FUSE (40A, 40A) ENGINE STARTER Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: The antenna should be installed only if the ambient air temperature is 15 C (60 F) or above. 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. FUSE (3A) CONTROL UNIT AD Without vehicle security FUSE (3A) FUSE (40A, 40A) ENGINE STARTER HOOD LOCK HOOD SWITCH CONTROL UNIT AD 4 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

5 3. Touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity. SMALL FLAT-TIP SCREWDRIVER CONTROL UNIT 6. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the protective tape will attach. Remove the backing from the protective tape. Attach the protective tape to the control unit over the switches. Discharge any static electricity. CONTROL UNIT SWITCHES SWITCHES SET PROTECTIVE SWITCHES TAPE BACKING Clean AS SW:1 RR Junction unit > OFF SW:2 Trunk or Tailgate > ON SW:3 Smart Entry > OFF SW:4 Horn or Buzzer Answerback ---- > OFF Removing the Vehicle Parts 7. Remove the right and left map light lens (four retaining tabs each). Do not damage the lenses. ROOF CONSOLE SW:5 Trunk Main SW > OFF SW:6 Reserve > OFF AD 4. Check the positions of the switches on the control unit. NOTE: The switches must be set before the control unit is plugged in. If the switch settings are not correct, the remote engine starter will not operate correctly. If you change the switch settings with the unit connected, you must disconnect the unit, then reconnect it before the control unit recognizes the new settings. 5. Using a small flat-tip screwdriver, adjust the switches on the control unit as shown. 4 RETAINING TABS LEFT MAP LIGHT LENS RIGHT MAP LIGHT LENS 4 RETAINING TABS PLASTIC TRIM TOOL AD 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 5 of 28

6 8. Remove the roof console (four bolts and unplug the vehicle connectors). ROOF CONSOLE 10. Pull back the weatherstrip as shown. CLIP RETAINING TAB Lightly tap. RETAINING TAB Collapsed. BODY CLIP Remains on the vehicle panel. PIN Comes off from the clip. Pull. S BODY WEATHERSTRIP Pull back. CLIP Pushed deep behind the vehicle panel. BODY AREA MARKED SIDE CURTAIN AIRBAG 2 SILVER BOLTS 2 BLACK BOLTS Y CLIP SHOP TOWEL 9. Using a flat-tip screwdriver wrapped with a shop towel, remove the right and left sun visor holders. LEFT SUN VISOR HOLDER LEFT A-PILLAR TRIM TRIANGLE MARK Tap perpendicularly with rubber mallet. RUBBER MALLET BD 11. Using a rubber mallet wrapped with a shop towel, lightly tap the area marked SIDE CURTAIN AIRBAG on the top of the left A-pillar trim to push in the vehicle clip. Make sure to tap area perpendicular to the A-pillar trim. Push. Turn. SHOP TOWEL FLAT-TIP SCREWDRIVER 2 SUN VISOR HOLDERS RIGHT SUN VISOR HOLDER AB 6 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

7 12. Pull away the weatherstrip as shown. 15. Remove the driver s lower cover (seven clips and two hooks). 2 CLIPS 7 CLIPS WEATHERSTRIP Pull away. LEFT A-PILLAR TRIM 13. Remove the left A-pillar trim (two clips) B 14. Turn the knob on the driver s under cover. Remove the driver s under cover (one pin and one clip). DRIVER S LOWER COVER 2 HOOKS 16. Remove the left front side step trim (three clips) B 3 CLIPS KNOB Turn. PIN DRIVER S UNDER COVER CLIP LEFT FRONT SIDE STEP TRIM B B 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 7 of 28

8 17. Pull away the weatherstrip. WEATHERSTRIP Pull away. 2 CLIPS 21. Remove the steering column lower cover (two selftapping screws and one screw). STEERING COLUMN LOWER COVER LEFT KICK PANEL 18. Remove the left kick panel (two clips) B 2 SELF-TAPPING SCREWS SCREW Y 19. Lower the tilt lever and pull the steering wheel outward. Insert a flat-tip screwdriver into the guide on the underside of the steering column lower cover and release the retaining tab. STEERING COLUMN UPPER COVER Push. STEERING COLUMN LOWER COVER 3 RETAINING TABS RETAINING TAB TILT LEVER GUIDE FLAT-TIP SCREWDRIVER 20. Remove the steering column upper cover (three retaining tabs) K 8 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

9 Installing the Antenna 22. Using two pairs of needle nose pliers, bend the antenna plate according to the measurements shown. 23. Using scissors, cut out the template. Cut out. PLATE 18 mm (0.7 in.) TEMPLATE 24 mm (0.9 in.) K 24. Align the template with the edge of the black ceramic paint, and secure it to the windshield with tape. REAR VIEW MIRROR BLACK CERAMIC PAINT NEEDLE NOSE PLIERS EDGE OF BLACK CERAMIC PAINT SCALE PLATE AD WINDSHIELD TEMPLATE TAPE Align these edges with the edges of the black ceramic paint AD 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 9 of 28

10 25. Measure the antenna cable as shown. Wrap three urethane tapes onto the antenna cable in those positions. 28. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the antenna will attach. Allow it to dry before proceeding. URETHANE TAPE HEADLINER 390 mm (15 in.) CABLE 720 mm (28 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) TEMPLATE Cut. 30 mm (1.2 in.) PLATE ADHESIVE BACKING AD URETHANE TAPE HALF URETHANE TAPE 6N3003AK 26. Cut two urethane tapes in half. Wrap three of the half pieces of urethane tape around the antenna cable as shown. 29. Remove the adhesive backing from the antenna, insert the antenna plate under the headliner, align the antenna with the template, and attach the antenna to the windshield. 30. Remove the template. 31. Push the antenna cable into the headliner as shown. Be careful not to crease the headliner. 27. Cut the urethane tape as shown. Attach the urethane tape to the antenna plate as shown. Cut. 60 mm (2.4 in.) 15 mm (0.6 in.) HEADLINER URETHANE TAPE CABLE Align. PLATE AD BK 10 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

11 32. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the urethane tape will attach. Cut the urethane tape remaining from step 27 as shown. Secure the antenna cable to the vehicle panel with the piece of urethane tape. Be careful not to crease the headliner. 34. Route the antenna cable along the left A-pillar and secure it to the vehicle harness with five wire ties as shown. CABLE 5 WIRE TIES CLIP URETHANE TAPE LEFT A-PILLAR CABLE PANEL URETHANE TAPE Remaining tape from step 27. URETHANE TAPE CABLE AD 35. Pull away the weatherstrip AK 33. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the urethane tape will attach. Secure the antenna cable to the vehicle panel with one urethane tape. Be careful not to crease the headliner. LEFT A-PILLAR WEATHERSTRIP Pull away. DASHBOARD CABLE CABLE AK PANEL URETHANE TAPE 36. Route the antenna cable down under the dashboard. Tuck the antenna cable between the left A-pillar and the dashboard, and reinstall the weatherstrip AD 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 11 of 28

12 Routing the Engine Starter Harness 37. Route the engine starter harness as shown. 41. Unlock the vehicle 42-pin connector by pushing the retaining tab on the connector, and unplugging the connector from the fuse box. 42-PIN Push. 2-PIN RETAINING TAB FUSE BOX DRIVER S LOWER COVER OPENING BD 4-PIN 2-PIN 4-PIN AD 38. Using isopropyl alcohol on a shop towel, thoroughly clean the areas where the 40A fuse labels and the 3A fuse label will attach. 3 RELAYS 42. Unplug the vehicle 4-pin connector and the 2-pin connector from the top of the fuse box as shown. 43. Wrap two urethane tapes to the vehicle 4-pin connector and 2-pin connector. RELAY BLOCK FUSE CASE 4-PIN AND 2-PIN S URETHANE TAPE 40A FUSE LABEL WIRE TIE 3A FUSE LABEL BD 39. Attach the 40A fuse labels and the 3A fuse labels to the relay block and the fuse case of the engine starter harness. 40. Plug the three relays into the relay block of the engine starter harness AD 44. Secure the vehicle 4-pin connector and 2-pin connector to the vehicle harness using a wire tie. 12 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

13 45. Plug the engine starter harness 4-pin and 2-pin connectors into the fuse box. Make sure the engine starter harness 4-pin and 2-pin connectors are plugged in securely. A loose connector can cause the engine to stall. Pull the connector and check for securely locking. 42-PIN 49. Unplug the vehicle 20-pin connector from the right side of the fuse box and plug it into the engine starter harness 20-pin connector as shown. Plug the engine starter harness 20-pin connector into the fuse box. FUSE BOX 20-PIN FRONT VIEW ENGINE STARTER 20-PIN 20-PIN 4-PIN 46. Reconnect the vehicle 42-pin connector into the fuse box. 47. Route the antenna cable as shown. GROUND TERMINAL 2-PIN BD GROUND BOLT (Reuse.) 20-PIN BD 50. Unplug the vehicle 23-pin connector from the underside of the fuse box and plug the engine starter harness 23-pin connector (white) into the fuse box. 23-PIN (White) FUSE BOX 23-PIN CABLE BD 23-PIN BD 48. Remove the vehicle ground bolt from the vehicle. Secure the engine starter harness ground terminal with the vehicle ground bolt American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 13 of 28

14 51. Unplug the vehicle 24-pin connector from the underside of the fuse box and plug it into the engine starter harness 24-pin connector as shown. FUSE BOX 24-PIN 55. Secure the vehicle fuse case to the vehicle harness with one wire tie. WIRE TIE FUSE BOX 24-PIN 24-PIN 24-PIN BD 52. Install the engine starter harness 24-pin connector to the 24-pin connector on the underside of the fuse box as shown. FUSE BOX FUSE CASE ENGINE STARTER FUSE CASE 20-PIN BD 56. Install the engine starter harness fuse case to the vehicle 20-pin connector. 53. Remove the vehicle fuse case. URETHANE TAPE 57. Secure the antenna cable to the engine starter harness with one wire tie. 23-PIN (Blue) WIRE TIE CABLE FUSE BOX URETHANE TAPE FUSE CASE BD ENGINE STARTER SRS (Yellow) ENGINE STARTER 54. Wrap the vehicle fuse case with one urethane tape half cut in step WIRE TIES BD 58. Secure the engine starter harness 23-pin connector (blue), and the engine starter harness to the vehicle harness with three wire ties. 14 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

15 59. Attach one wire tie with clip to the engine starter harness at the white tape, then push the clip into the hole in the steering hanger beam. 62. Attach the wire tie with clip to the engine starter harness at the white tape, then push the clip into the hole in the bracket. STEERING HANGER BEAM WHITE TAPE WIRE TIE WITH CLIP ENGINE STARTER WIRE TIE WITH CLIP WHITE TAPE BRACKET ENGINE STARTER CABLE 60. Route the antenna cable BD 61. Install the bracket on the instrument panel with one 6 x 12 mm washer bolt and one 6 mm flange nut. 63. Route the engine starter harness 7-pin connectors (brown, green, white) to the steering column. 7-PIN S STEERING COLUMN BD INSTRUMENT PANEL 6 mm FLANGE NUT BRACKET 6 x 12 mm WASHER BOLT BD 6D01120Y 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 15 of 28

16 64. Unplug the vehicle 7-pin connector (brown) from the ignition switch and plug in the engine starter harness 7-pin connector (brown) as shown. Make sure the engine starter harness 7-pin connector (brown) is plugged in securely. A loose connector can cause the engine to stall. 67. Place the vehicle 7-pin connector (brown) into the gap of the column. 7-PIN (Brown) PANEL 7-PIN (Brown) IGNITION SWITCH URETHANE TAPE WIRE TIE AD 68. Secure the engine starter harness to the vehicle harness with two wire ties. Pull the connector and make sure it is locked. 7-PIN (Brown) ENGINE STARTER AK 69. Unplug the vehicle 8-pin connector (black) from the wiper switch. Plug the engine starter harness 8-pin connector to the wiper switch. 65. Wrap the vehicle 7-pin connector (brown) with a urethane tape. 66. Unplug the vehicle 7-pin connector (white) from the ignition switch and plug in the engine starter harness 7-pin connector (white) as shown. Plug the vehicle 7-pin connector into the engine starter harness 7-pin connector. 8-PIN (Black) 8-PIN 7-PIN (white) IGNITION SWITCH 7-PIN (White) WIPER SWITCH 6D01160Y ENGINE STARTER K 16 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

17 70. Plug the vehicle 8-pin connector (black) to the engine starter harness 8-pin connector. 73. Align the white tape on the engine starter harness to the vehicle clip, and secure the engine starter harness to the vehicle harness with one wire tie. 8-PIN (Black) WHITE TAPE WIRE TIE ENGINE STARTER RELAY BLOCK WIRE TIE 8-PIN (Black) FRAME 6D01171Y 71. Secure the engine starter harness 8-pin connector (black) to the vehicle harness with one wire tie. 72. Install the engine starter harness fuse case on the vehicle relay block. CLIP 74. Secure the relay block of the engine starter harness to the vehicle frame. 75. Align the antenna cable as shown BD RELAY BLOCK FUSE CASE 28-PIN 70 mm CABLE STEERING SHAFT BD WIRE TIE STEERING SHAFT BD 76. Secure the engine starter harness and antenna cable to the vehicle harness with one wire tie American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 17 of 28

18 77. Bundle the excess antenna cable and secure it to the vehicle harness with one wire tie. CABLE Bundle the excess. 80. Install the control unit to the control unit bracket. CONTROL UNIT WIRE TIE DRIVER S UNDER COVER CONTROL UNIT CONTROL UNIT BRACKET TA WIRE TIE BD 78. Secure the antenna cable to the vehicle harness with two wire ties. 79. Install the control unit bracket on the driver s under cover with two 5 x 12 mm self-tapping screws. SELF-TAPPING SCREW, 5 x 12 mm CONTROL UNIT BRACKET AD 81. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the urethane tape will attach. URETHANE TAPE CONTROL UNIT BRACKET BRACKET STEERING COLUMN LOWER COVER DRIVER S UNDER COVER AD AK 82. Attach a urethane tape to the bracket on the steering column lower cover. 18 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

19 If the vehicle is equipped with a vehicle security system, go to step 104; otherwise, continue with step Remove the radiator cover (five clips A and two clips B). 87. Remove four self-tapping screws from the left inner fender. 2 CLIPS B 5 CLIPS A LEFT INNER FENDER RADIATOR COVER AX 4 SELF-TAPPING SCREWS 88. Turn down the left inner fender (six clips) AK 84. Remove the left fender arch (one clip, two self-tapping screws, and six clips). LEFT INNER FENDER OLD SPACER SPACER ADHESIVE BACKING Remove. 6 CLIPS LEFT FENDER ARCH 6 CLIPS 2 SELF-TAPPING SCREWS AK CLIP AK 85. Remove two old spacers from left fender arch. 86. Using isopropyl alcohol, thoroughly clean the area where the spacers will attach. Replace the two spacers will a new one American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 19 of 28

20 89. Using a felt-tip pen, mark around the vehicle hood lock for reinstallation. 93. Align the new hood lock with the marks you made, and install it with the three bolts you removed. Torque the bolts to 10 N. m (7.2 lbf-ft). HOOD LOCK MARK FELT-TIP PEN MARK HOOD LOCK 3 BOLTS 3 BOLTS (Reuse.) Y 90. Remove the hood lock (three bolts). 91. Remove the hood lock opener cable from the vehicle hood lock Y 94. Route the grommet end of the hood switch harness from the engine compartment into the left fender as shown. HOOD LOCK (Discard.) GROMMET LEFT FENDER SIDE FRONT HOOD LOCK OPENER CABLE NEW HOOD LOCK HOOD SWITCH Y 92. Attach the hood lock opener cable to the new hood lock. ENGINE COMPARTMENT Y 20 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

21 95. Route the hood switch harness. Secure the hood switch harness to the vehicle panel with the three clips installed on the hood switch harness. 98. Route the hood switch harness along the vehicle harness to the center of the vehicle. Secure the hood switch harness to the vehicle harness with six wire ties. FRONT HOOD SWITCH GREEN TAPE FRONT GREEN TAPE 6 WIRE TIES PANEL CABLE CLIP 3 HOOD SWITCH CLIPS 96. Attach the cable clip to the hood switch harness at the green tape, and secure it to the vehicle panel. 97. Remove the vehicle grommet. Route the hood switch harness 2-pin connector into the interior compartment Y 99. Plug the hood lock 2-pin connector to the hood switch harness 2-pin connector and secure the connector to the vehicle panel. HOOD SWITCH HOOD SWITCH 2-PIN FRONT HOOD SWITCH HOOD LOCK 2-PIN GROMMET PANEL Y INSIDE OUTSIDE Install the grommet. GROMMET (Discard.) Y 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 21 of 28

22 100. Remove the tape and plug the hood switch harness 2-pin connector into the engine starter harness 2-pin connector. Secure the connector to the vehicle harness with one wire tie Plug the engine starter harness 28-pin connector and antenna cable into the control unit as shown. DRIVER S LOWER COVER 28-PIN CABLE ENGINE STARTER 2-PIN TAPE WIRE TIE PLUGGED S HOOD SWITCH HOOD SWITCH 2-PIN BD DRIVER S UNDER COVER CABLE CONTROL UNIT CONTROL UNIT 28-PIN 102. Reinstall the driver s lower cover and the driver s under cover Using isopropyl alcohol on a shop towel, thoroughly clean the area where the caution label will attach. HOOD ADHESIVE BACKING CAUTION LABEL 104. Attach the caution label to the hood. 6D2401AK 22 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

23 Reinstalling the Left A-Pillar Trim 105. Check that the left A-pillar trim and the left A-pillar trim pin are not damaged, and install the clip on the pin. CLIP Remove. CLIP 107. Check that all wire harness are routed properly and all connectors are plugged in Reinstall all removed parts. Check that all clips and other fasteners are installed securely Reconnect the negative cable to the battery Enter the customer s radio anti-theft code, and reset the radio station presets Reset the clock Perform REMOTE REGISTRATION and FUNCTION CHECK. LEFT A-PILLAR LEFT A-PILLAR TRIM PIN H 106. Position the clip perpendicular to the hole in the left A-pillar. Install the clip by lightly pushing the left A-pillar trim at the area marked SIDE CURTAIN AIRBAG. Check that the airbag is not pinched by the clip. Do not push the left A-pillar trim excessively. LEFT A-PILLAR CLIP PANEL CLIP AREA MARKED SIDE CURTAIN AIRBAG LEFT A-PILLAR TRIM Y 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 23 of 28

24 If the vehicle is equipped with automatic climate control, do the following. Setting the Automatic Defrost Function Setting the automatic defrost function must be done while the vehicle air conditioner is in the OFF position. Turn the air conditioner to the OFF position with the ignition switch in the ON (II) position, then turn the ignition switch to the LOCK (0) position. While holding the REAR DEFOGGER switch and the RECIRCULATION switch, turn the ignition switch to the ON (II) position. The Set temperature and a letter (CL or AC) on the air conditioner display will blink after 5 seconds, and stays on after 10 seconds. The letter CL indicates that the automatic defrost function is OFF, and the letter AC indicates that the automatic defrost function is ON. 5 Seconds after turning the ignition switch to ON (II) (indicating current setting) REAR DEFOGGER switch RECIRCU- LATION switch IGNITION switch 0 II 10 Seconds after turning the ignition switch to ON (II) K S 24 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

25 REMOTE REGISTRATION 1. Get the PCM Code from ISIS. 5. Select Honda Systems, then click the check button. CAR ICON Select Honda Systems. CHECK BUTTON AS 2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch on. 3. Start the HDS, and click the car icon AS 6. Select R/C ENG STARTER and click the check button. 4. Input the VIN and other information, then click the check button. Select R/C ENG STARTER. CHECK BUTTON AS Input the VIN and other information. CHECK BUTTON AS 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 25 of 28

26 7. Check that REMARKS is shown, then click the check button. Check that REMARKS is shown. 9. Check that Obtain PCM-code (IMMOBILIZER PCM CODE) from in. This vehicle s VIN will be required to obtain the password. (USA) is shown, then click the check button. Check that Obtain PCM-code (IMMOBILIZER PCM CODE) from in. This vehicle s VIN will be required to obtain the password. (USA) is shown. CHECK BUTTON AS 8. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button. CHECK BUTTON AS 10. Input the PCM Code, then click the check button. NOTE: To ensure security, the PCM code (password) is changed every day, so it is impossible to register the remote controlled engine starter if the date of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same. Input the PCM Code. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT. CHECK BUTTON AS CHECK BUTTON AS 26 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.

27 11. Check that The registration of the Remote Control Engine Starter Unit has been completed is shown, then click the check button. Check that The registration of the Remote Control Engine Starter Unit has been completed is shown. CHECK BUTTON AS 12. Check that Check that the engine can be started by the Transmitter is shown, then click the check button. Check that Check that the engine can be started by the Transmitter is shown. CHECK BUTTON AS 13. Perform the function test on the next page, then remove the HDS American Honda Motor Co., Inc. All Rights Reserved. AII (0910) 27 of 28

28 FUNCTION CHECK Operating Conditions Hood is closed Shift lever in park The key is out of the ignition All doors and tailgate closed and locked Inspection 1. Within 1 second, press the command button, and then the start button on the transmitter. The engine should start if all operating conditions are met. Does the engine start? Yes - Operation is normal. No: Make sure all Operating Conditions are met. Check the engine starter harness connections. Connect the HDS and check for an indicated failure. (Refer to the appropriate service manual for details.) 2. Press the command button on the transmitter, and within 1 second, press the stop button. The engine should stop. Does the engine stop? Yes - Operation is normal. No - Check the engine starter harness connections. 3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions: NOTE: After each test the ignition key must be cycled, or the driver s door must be opened and closed Move the shift lever out of the P position. Unlock or open the doors or the tailgate. Open the hood. Insert the key in the ignition. Press on the brake pedal. Does the engine stop after each of these tests? STOP BUTTON TRANSMITTER DISPLAY COMMAND BUTTON START BUTTON AY Yes - Operation is normal. No - Check the engine starter harness connections. 4. Check that the power window and the moonroof do not function and the shift lever does not move to any position but the P position when the engine is started with the transmitter. 5. Press the command button on the transmitter two times and check the vehicle condition on the display. 6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away, and in direct sight. 28 of 28 AII (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.