INSTALLATION INSTRUCTIONS
|
|
- Dulcie May Page
- 5 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT BMW E46 COUPE Document# Support: Note: This kit was designed for a standard single pump Radium Engineering fuel surge tank. There are 2 common ways to relieve fuel pressure on the BMW. 1. Option 1: Open glove compartment. Rotate the 2 white tabs on the top-inside of the glove box in order to release and swing the fuse box down and remove fuse 54. Start vehicle and allow engine to stall. Turn off car and remove key. Reinstall fuse and glove box. 2. Option 2: There is a Schrader bleed valve found on the factory fuel pressure regulator underneath the vehicle, shown at right. 2. Open Trunk. Remove right side socket housing for tail light. Take out luggage compartment floor trim panel (1). Unclip the two fasteners that secure the plastic battery cover on the rear right side of the trunk. Remove the plastic cover to gain access to the battery. 3. Unscrew and disconnect negative terminal of the battery (G1). Caution: Disconnecting the battery (G1) may cancel the fault memories of some control units. Consequently, before disconnecting the car's battery, always interrogate the fault memories. Investigate stored faults and, once any faults have been remedied, cancel the fault memory. 4. Pull out emergency release mechanism for tank cap a little. Unclip cable (1) from clip (2). Release and fold down each rear seat using the 2 release handles located in the trunk ceiling. Turn rotary clip (1) 90 and remove.
2 5. Partially release panel for trunk separating wall. Partially pry out outer trim (1) and remove trunk wheel arch trim (2). 6. Locate the M8 bolts that secure the two rear seat lock receivers to the trunk ceiling. Using a 13mm socket, remove these 4 bolts (2 for each side) and discard. Note: the receivers will temporarily be free and loose within the ceiling. 7. Using the included long M8 bolts and washers, secure the fuel surge tank mounting bracket to these rear seat anchor points (as shown). 8. Using 2 of the included zip-ties, secure the wiring harness to the bracket. Temporarily let the fuel surge tank s circular quick disconnect plug dangle, as shown. 9. Using the included M5 bolt and nut, secure the relay and fuse to the single mounting hole located on the left side of the Radium FST mounting bracket.
3 10. Using the four included M6 bolts, secure the FST to the bracket. Note the keyway of the circular fuel surge tank connector. Insert and press it into the mating connector on the FST. Spin the threaded collar clockwise until it is fully seated and tight. Route the wiring harness around the trunk and down towards the battery. Remove the 10mm battery nuts and connect the "Power" and "Ground" ring terminals to the respective battery terminals. 11. Locate the black fuel pump relay. On USA coupe models (shown), it is located in the trunk on the right side wall above the shock absorber mount. NOTE: For all convertibles and some foreign E46 M3 coupes, the fuel pump relay is in various locations. In some models, it will be found below the right rear quarter window behind the interior panel. To be certain of the fuel pump relay location, check the BMW E46 M3 Factory Service Manual for your specific region. 12. The relay trigger for the Radium fuel surge tank's pump will need to be tapped off the factory BMW fuel pump's relay wire. NOTE: The pump in the main fuel tank will now be used as a low pressure high flow lift pump As shown, unclip the two relays from the wall as a single unit using a flat head screwdriver or special needle nose pliers. 13. There should be two large gauge wires that are red with a white stripe. Reference the specific wire pointed at in the picture. This will be tapped into. It is nearest the "55" molded into the relay connector. To verify this is the correct wire, there should be continuity between this wire and the factory BMW fuel pump's positive wire. 14. Find the Posi-Tap wire connector in the kit. Unscrew both ends. Insert the red/white wire into the slotted area of the one side of the connector, as shown.
4 15. Strip the insulation of the included blue wire back to expose about 3/8" of copper. Insert the wire through the other half of the Posi-Tap wire connector, as shown. 16. Screw the two connector halves together as shown and give the wire a quick tug to make sure it seated properly. Note: There are detailed instructional videos on the internet on how to assemble Posi-Tap wire connectors. Next, find the Weather Pack connector, terminal, and cable seal in the kit. Strip the opposite side of the blue wire s insulation. Slip on the cable seal. Crimp the back half of the terminal to the cable seal and the front half of the terminal to the exposed wire. Insert into the assembly into the Weather Pack connector and latch down. Plug this into the mating Weather Pack connector in the Radium harness. The Radium fuel surge tank is now completely wired. 17. Break loose the lug bolts on the right rear wheels. Put the vehicle on a lift or jack up the rear of the vehicle and safely place down jack stands. Remove the right rear wheel. 18. The rear under brace will need to be removed. Using a 16mm socket, remove the 3 bolts that secure the under-brace to the chassis. 19. The underside plastic rear panel that covers the right side of the gas tank will also need to be removed.
5 20. Once all of the fasteners are removed, the panel will need to be shifted towards the back of the vehicle to unlock it from the chassis. 21. Shown to the right is the aforementioned cover that is to be removed. 22. Pry and fold the front most section of carpet in the trunk towards the front of the vehicle. There is a factory sheet metal hole (shown). However, this is hidden underneath the tar board insulation. From underneath the car, find the aforementioned rubber factory plug near the right rear suspension and pierce it with a blunt object such as a screwdriver. 23. From the top side, pull out the remains of the rubber plug and clean the excess tar board to expose the symmetrical 1 hole. Using the included bulkhead plate, lineup and position the rear most left side hole to the center of the trunk hole. Trace the location of the three remaining circular holes using a marker. 24. Using the marked circles as a reference, drill three 5/8 holes (as shown). Clean up all the drilled holes and be sure they are free of debris. Note: The factory large hole is used as a reference point for lining everything up and allowing the included preassembled hoses to reach.
6 25. Fold the section of carpet back down. Use a razor blade, such as a utility knife, and make 4 corresponding holes in the carpet. 26. Removing the 40mm ID x 170mm long fuel filler hose, from underneath the car, will free up a little bit of room when inserting hoses through this area. Using a 6mm ratcheting socket, loosen the two hose clamps. Slide the hose back and forth until it releases from the hard tubes on each end. 27. There are 8 hoses included in the kit. Four of them are 24" long and are identical (not shown). These 4 will be used in the trunk. The other 4 hoses (shown) connect underneath the vehicle from bulkheads to the top of the gas tank. Depending on where they connect, many of these hose ends require an included adapter fitting, described below. Two hoses route to the left side of the tank. The other two hoses are identical and route to the right side of the tank. Apply some tape (not included) to both ends of the hose which will route from the green FST pump outlet fitting to the OEM hose that routes to the engine s fuel rail. This will make it easier later on to identify this specific hose. 28. The "green" bulkhead fitting is the FST's pump outlet port. For starvation protection, this should be drawing fuel from the FST bottom. This port will route to the factory hose on the right of the fuel tank which normally connects to the stock pump assembly. For fuel starvation efficiency, the top port should route to the main fuel tank's return barb found on the left side. The functionality of the other 2 ports on the FST is not important. 29. Screw short end of bulkhead fittings to each 45 degree hose end with an 11/16" wrench. Note: Unlike tapered threads, JIC (-AN) fittings don't require excessive torque or sealing compound. From underneath, insert these bulkheads through the drilled holes, carpet, and bulkhead plate using the following hole locations: Back right hole = short hose with straight hose end (marked with tape) Front right hole = short hose with straight hose end (not marked with tape) Back left hole = long hose with straight hose end Front left hole = long hose missing a hose end
7 30. From the trunk, secure each bulkhead fitting with the included bulkhead nuts. Next, all 4 "equal length" hoses will be routed between the fuel surge tank and the bulkhead fittings. Note: The bulkhead fittings were organized into a specific hole to make the slack in the trunk hose's consistent (as shown). 31. An aluminum wrench is recommended for all fittings in the interior to resist black anodize marring. Back right hole = bottom "green" FST fitting (taped hose) Front right hole = front FST port fitting (non-taped hose) Back left hole = rear FST port fitting Front left hole = top FST port fitting Tighten all fittings in the trunk area. 32. Next, the 4 hoses will need to run over the top of the main fuel tank. From underneath the vehicle, remove the M8 bolt (shown) that secures the large fuel tank using a 13mm socket. Let the large clamp hang. Allow the BMW fuel tank to sag down a few inches just enough to feed the 4 hoses up on top of the right side of the tank. Support the tank. Use the included zip-ties to keep the hoses away from the rear control arm as best as you can. Remember, the suspension will compress when the vehicle is back on the ground. 33. From inside the cabin, pull up to unclip the rear bench seat and remove from vehicle. Underneath the bench, there are rubber mats. Fold the mats back carefully to expose the 2 metal covers. Remove the four M6 nuts (shown) on each cover using a 10mm socket. It is a good idea to clean each side as they will be dirty. On the right side opening, find the 4 hoses and pull them into view. Route the 2 longer hoses to the left side opening underneath the sheet metal but on top of the BMW fuel tank. 34. Under the left side cover is where the stock BMW fuel system s return hose from the BMW fuel pressure regulator reenters the main BMW fuel tank. To remove the factory pinch clamp found on the return hose, simply use a flat head screwdriver and pry the crimped section up and away, as shown. Discard this "one-time-use" clamp.
8 35. Shown to the right is how the clamp will be removed using a screwdriver. Next, gently pull the hose off the OEM barb. CAUTION: When running fuel pressures over 5Bar, we have seen instances when the throttle is chopped after a high boost run, the pressure spike after the FPR dislodges the internal connection inside the tank. This prevents fuel from siphoning to the right side of the "saddle bag" tank. The BMW fuel level gauge will not read properly. Fortunately, this should never happen with a FST system. 36. Locate the -6AN male to barb fitting in the kit. Lubricate the barbs with oil and install to the OEM hose, as shown. Next, install the included worm drive hose clamp. Secure the long hose (with the straight -6AN end) onto this fitting. 37. From the left side opening, pull out the hose which does not have a crimped hose end on it. Find one of the small hose clamps in the kit and insert it over the hose. Lubricate both the barb and the inside of the hose liberally. Gently push the PTFE (Teflon) hose over the blue barb. It will be nice and tight. DO NOT FORCE IT AS THE OEM PLASTIC IS BRITTLE! Secure the clamp onto the hose, as shown. 38. Underneath the right side cover is where the original BMW fuel pump hanger assembly resides. To release the factory quick disconnect fitting, simply rotate the connector until both outer tabs can be accessed with a thumb and index finger. First, pull the connector towards the center of the hanger. Next, squeeze the 2 tabs and then gently pull away from the mating tube, as shown. Have a rag handy as fuel will instantly leak out of this connection. 39. From the right side opening, find the hose that does NOT have tape identification stuck to it. Route it around the tank towards the front of the vehicle. Secure the included SAE quick disconnect fitting to the hose end using 11/16 and 3/4 wrenches. Lubricate the blue OEM pump outlet connector with oil and push on the SAE fitting. DO NOT FORCE IT AS THE OEM PLASTIC IS BRITTLE! Install the green lock and secure with a 5/64 Allen wrench.
9 40. From the right side opening, find the last short hose that DOES have tape identification on it. Also, find the male quick disconnect adapter fitting in the kit. Screw and secure the - 6AN fittings together, as shown. Insert the Radium quick disconnect male adapter fitting into the BMW female quick disconnect fitting until it fully seats and a positive click is felt. 41. Reconnect the battery. The FST must be fully primed with fuel before the engine will start. Remove the fuse located on the Radium mount. Cycle the ignition several times. Wait 10 seconds each time to allow the BMW main relay to cycle. This will activate the lift fuel pump for a few seconds each time. After 3-4 cycles it should be ready to start. Replace FST fuse. Cycle the ignition and listen for the FST pump to confirm the Radium electrical was performed properly. Start the vehicle. The engine may run rough for a few seconds until all air is bled from the system. 42. Start the engine and INSPECT ALL CONNECTIONS FOR LEAKS! Next, reinstall all parts that were removed. When putting the trunk back together, the rubberized carpet will need to be cut in a half circle, as shown in red. Test-drive the vehicle and inspect again for fluid leaks. If no leaks are found, the installation of the Radium FST is complete.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit wasn t designed for a FST-R, but can be accomplished. 1.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALL KIT Honda S2000 Document# 19-0063 Support: info@radiumauto.com WARNING: DO NOT SMOKE WHILE WORKING ON FUEL SYSTEMS. KEEP SPARKS AND OPEN FLAMES AWAY FROM
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL PUMP SLEEVE INSTALLATION KIT 2001-2006 BMW E46 M3 Document# 19-0058 Customer Support: info@radiumauto.com 1. There are 2 common ways to relieve fuel pressure on the BMW.
More informationINSTALLATION INSTRUCTIONS FUEL SURGE TANK KIT
INSTALLATION INSTRUCTIONS FUEL SURGE TANK KIT BMW E46 3-Series, Excl Convertible Document: 19-0056 Support: info@radiumauto.com Relieve fuel pressure in vehicle before beginingthe installation. Disconnect
More informationINSTALLATION INSTRUCTIONS Mitsubishi Lancer Evolution VIII / IX Fuel Surge Tank Kit Document#
d INSTALLATION INSTRUCTIONS Mitsubishi Lancer Evolution VIII / IX Fuel Surge Tank Kit Document# 19-0077 Brie Tech Support: info@radiumauto.com CAUTION: Exercise extreme caution when working with the fuel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FST KIT FOR PORT INJECTION 2013+ FORD FOCUS ECOBOOST Document: 19-0168 Support: info@radiumauto.com Working under the vehicle is required. This installation is best performed
More informationINSTALLATION INSTRUCTIONS
1. Note: It is recommended this install be done with a minimal amount of fuel in the tank. This will reduce fuel spills and make installation easier and safer. Draining the tank is recommended. INSTALLATION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK KIT 2013+ FORD FOCUS ECOBOOST Document: 19-0168 Support: info@radiumauto.com Working under the vehicle is required. This installation is best performed with the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL PUMP HANGER 08+ MITSUBISHI LANCER EVOLUTION X Support: info@radiumauto.com Document# 19-0116 WARNING: DO NOT EXPOSE WORK AREA TO ANY SPARKS OR FIRE. DO NOT SMOKE WHILE WORKING
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL PUMP HANGER MITSUBISHI LANCER EVOLUTION X Support: info@radiumauto.com Document# 19-0116 WARNING: DO NOT EXPOSE WORK AREA TO ANY SPARKS OR FIRE. DO NOT SMOKE WHILE WORKING
More informationINSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT
INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT MITSUBISHI LANCER EVOLUTION X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM
More informationINSTALLATION INSTRUCTIONS FUEL RAIL
INSTALLATION INSTRUCTIONS FUEL RAIL MITSUBISHI EVO X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM PREPARING THE VEHICLE:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL PUMP HANGER FORD MUSTANG: 2011+ S197 AND S550 Support: info@radiumauto.com Document# 19-0161 WARNING: DO NOT EXPOSE WORK AREA TO ANY SPARKS OR FIRE. DO NOT SMOKE WHILE WORKING
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document 19-0009RevC FUEL SURGE TANK INSTALLATION KIT 2004+ LOTUS ELISE/EXIGE (2ZZ-GE) FRAME RAIL MOUNT Customer Service: info@radiumauto.com READ AND UNDERSTAND THESE INSTRUCTIONS
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationRaxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler)
Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler) Installation Time: 2.5-3Hrs Tools Required: 7mm Socket & Driver 10mm Socket 10mm Open end wrench Knife / Razor blade Zip-ties Wire Cutters Needle
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationInstallation Instructions for Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights
Installation Instructions for 2015-2018 Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights This kit is designed to allow use of your factory fog light operation along with an addition auxiliary
More informationInstallation Instructions
Installation Instructions Jeep JK Unlimited (2007 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Bracket for ARB Compressor
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationINSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT
INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT 2015+ SUBARU WRX (LHD ONLY) Document: 19-0136 Support: info@radiumauto.com This document covers the installation of the Radium brake master cylinder brace
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS DUAL EXTERNAL PUMP FST Vertical & Horizontal Mount Customer Support: info@radiumauto.com Document: 19-0013 READ AND UNDERSTAND THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1-19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT
More informationINSTALLATION INSTRUCTIONS COOLANT TANK KIT
INSTALLATION INSTRUCTIONS COOLANT TANK KIT 2017+ Honda Civic Type-R Document: 19-0197 Support: info@radiumauto.com NOTES: Installation to be performed on engines that are completely cooled down. Do NOT
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FIESTA ST Document: 19-0175 Support: info@radiumauto.com STEPS 1-14 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0377) STEPS 15-35 COVER THE CRANKCASE CATCH CAN
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FIESTA ST Document: 19-0175 Support: info@radiumauto.com STEPS 1-14 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0377) STEPS 15-31 COVER THE CRANKCASE CATCH CAN
More information80703 & Backside License Plate Mount for Jeep JK Wrangler (80707) & 10+ (80703)
80703 Backside Mount 80707 Backside Mount REQUIRED TOOLS 10mm SOCKET 13mm SOCKET 4mm HEX KEY WIRE CRIMPS WIRE STRIPPERS ELECTICAL TAPE SCREW DRIVER KIT CONTAINS BACKSIDE MOUNT LICENSE PLATE BRACKET WITH
More informationBackside License Plate Mount for Jeep JK Wrangler
REQUIRED TOOLS 10mm SOCKET 13mm SOCKET 4mm HEX KEY WIRE CRIMPS WIRE STRIPPERS ELECTICAL TAPE SCREW DRIVER KIT CONTAINS BACKSIDE MOUNT LICENSE PLATE BRACKET WITH LEDS PLASTIC PASS-THROUGH GROMMET STAINLESS
More informationLethal Performance Dual FPDM Harness Kit Installation
Lethal Performance Dual FPDM Harness Kit Installation The Lethal Performance Dual FPDM Harness Kit is a plug-and-play modification. Depending on whether you are using the Lethal Performance wire upgrade
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationThank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+)
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+) Before You Start Please read instructions completely before installing. These
More informationBMW E46 Convertible Hydraulic Line #23 Replacement Guide Created by taylor192 of E46Fanatics.com
BMW E46 Convertible Hydraulic Line #23 Replacement Guide Created by taylor192 of E46Fanatics.com BMW E46 Line #23 Replacment Guide, page 1 of 23 Background: Line #23 runs from the valve block on the driver's
More informationDo not have any open flame or heat sources close to the installation
March 6, 2017 IS# 791 Page 1 of 16 Thank you for purchasing a Transfer Flow, Inc. 50-gallon replacement fuel system for your 2011-16 Ford diesel short bed pickup. This system will fit any 2x4 or 4x4 crew
More informationROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8
Installation Instructions P/N: 422128 (R1318-5231LITE) Fastback GT Convertible GT V8 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH ROUSH Active IO Exhaust Installation Instructions P/N: 422128
More informationPerformance Inlet Manifold
Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with
More informationCongratulations on purchasing the Edge Juice/Attitude system for the Dodge Cummins Diesel.
Getting Started About the Juice Congratulations on purchasing the Edge Juice/Attitude system for the Dodge Cummins Diesel. The Juice/Attitude system features an intelligent module (Juice) that acts as
More informationM-9424-M50CJ INTAKE MANIFOLD INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS COOLANT EXPANSION TANK FORD FOCUS Document: 19-0151 Support: info@radiumauto.com WARNINGS: DO NOT WORK ON THE COOLANT SYSTEM WHEN THE ENGINE IS AT OPERATING TEMPERATURE. WAIT
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN
More informationLEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More informationCarousel Unit User Manual Replacing the Check Stand Motor
Carousel Unit User Manual Replacing the Check Stand Motor 02/01/2017 1 Table of Contents Tools:... 3 Turn Off Power to the Unit:... 4 Remove Power Switch... 5 Remove Electric Eyes:... 6 Remove POS (Point-Of-Sale)
More informationClassic Light Bar Mustang
Classic Light Bar 2005-2012 Mustang Note: Read installation instructions before starting. Component List: 1 Light Bar Part #110000 1 Driver Side Bracket w/set Screw Part #115003 1 Passenger Side Bracket
More information#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Versa (2012) PART NUMBER: 999F3 AW008 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationLGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions
LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationRear Vision System Liftgate Emblem Camera for Aftermarket Display Ford Flex (Kit part number )
Rear Vision System Liftgate Emblem Camera for Aftermarket Display 2009-2012 Ford Flex (Kit part number 1008-6509) Kit Contents: Liftgate Emblem Mount with Camera Chassis Harness with RCA (Note: In some
More informationOwner smanual. Banks Ram-Air Intake System Chevrolet/GMC 8.1L Workhorse Class-A Motorhome. with Installation Instructions
Owner smanual with Installation Instructions Banks Ram-Air Intake System 2001-2008 Chevrolet/GMC 8.1L Workhorse Class-A Motorhome THIS MANUAL IS FOR USE WITH SYSTEMS 49194 AND 49195 Gale Banks Engineering
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationEvo X Walbro 450 Pump System
Evo X Walbro 450 Pump System Installation Guide Please contact us at sales@wtftuned.com with any additional questions Tools required: 8 mm socket and wrench, needle-nose pliers, razor, drill w/ 5/64 bit,
More informationAiraid Poweraid Throttle Body Spacer (11-13 V6):
Install Time: Less than 1 hour Required Tools: Flat blade screw driver ratchet 8mm socket 10mm socket Needle nose pliers or Channel locks Razor blade 2 small cable ties or electrical tape Airaid Poweraid
More informationRemove the 3-11mm nuts holding mirror on. Don t drop the nuts!
2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit
More informationWOC & WOC Top & Back Installation Instructions
Shown with optional Sun Roof WOC-900500-2 & WOC-900501-2 Top & Back Installation Instructions Install Order! Heater Door System Wiper on to Windshield Windshield Rear Panel Top Panel Tools needed: 5/16
More informationIndustrial Injections Compound Turbo Installation For 6.7L Scorpion
Industrial Injections Compound Turbo Installation For 6.7L Scorpion Step 1: Whenever you are doing an installation the first thing you should do is unhook the batteries to avoid arcing. You will need an
More informationPart# JL AIR IT UP 4 Tire On Board Air Delivery System. (Requires External Air Source)
Part# 18-1819 JL AIR IT UP 4 Tire On Board Air Delivery System (Requires External Air Source) The most up-to-date instructions always visit www.updownair.com www.updownair.com 833-226-4863 I M P O R T
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationACD-PRO Install in 2008 EvoX
Turning in a counter clockwise direction, unscrew ift knob ACD-PRO Install in 2008 EvoX Slide back and remove the floor console panel assembly Pull up to remove the center console tray Disconnect the plug
More informationMKVI Jetta Fog Light Kit
MKVI Jetta Fog Light Kit Part Number VW Jetta Fog Light Installation This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation
More informationInstallation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683
Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation
More informationInstallation of Auto Meter Cobalt Boost/Vacuum Gauge:
Installation of Auto Meter Cobalt Boost/Vacuum Gauge: Fitment: All 79-14 models. This installation was completed on a 2004 Mustang GT, and should be identical for all 1999-2004 model Mustangs. Time needed:
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationLGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions
LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT
More information2015 Copyright Maxspeed-Motorsports.com
1 Porsche PCM 3.1 Backup Camera Installation Instructions. Thank you for purchasing your product at www.maxspeedmotorsports.com Before you start please understand that these installation instructions are
More informationLEXUS CT 200h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-89100 Kit Contents Item # Quantity Req'd. Description 1 1 Door Sill, Front Right Hand 2 1 Door Sill, Front Left Hand 3 1 Door Sill, Rear Right Hand 4 1 Door Sill, Rear Left
More informationINSTALLATION INSTRUCTIONS FUEL HANGER SURGE TANK
INSTALLATION INSTRUCTIONS FUEL HANGER SURGE TANK BMW S65/N54/N55 Vehicles Document: 19-0189 Support: info@radiumauto.com STEP TOOLS NEEDED INSTRUCTIONS Itisrecommendedtorunthefueltankdryordrainthetanktoreducefuelspillsforaneasierandsafer
More informationIE Audi B9 S4, S5, A4, A5, Allroad FDS Intercooler Install Guide IETPCK1
IE Audi B9 S4, S5, A4, A5, Allroad FDS Intercooler Install Guide IETPCK1 Thank you for purchasing the best performing intercooler on the market! This instruction guide is used for installation of IE s
More informationZ-Gate Universal Shifter
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough
More informationThe steering column is of a modular construction and features easy to service electrical switches.
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column NOTE:
More informationSlingshot Rotrex Supercharger Kit
Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you
More informationRemove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationGetting Started. About the Juice. Congratulations on purchasing the Edge Juice/Attitude system for the Dodge Cummins Diesel.
Getting Started About the Juice Congratulations on purchasing the Edge Juice/Attitude system for the Dodge Cummins Diesel. The Juice/Attitude system features an intelligent module (Juice) that acts as
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Part# 22-7810 Jeep JK/JKU ARB Mounting Kit 2007-2018.5 For the most up to date instructions please visit www.updownair.com www.updownair.com 833 226 4863 IMPORTANT INFORMATION
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: R42H (2011) PART NUMBER: 999F3 AW000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description Service
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Rear Vision System Mirror Display 2013-Current Ram (Kit part number 1009-9518) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Rear
More informationSCION xb HEADREST DVD RSE Section I Installation Preparation. Part Number: PT
Section I Installation Preparation Part Number: PT900-52080 Kit Contents Item # Quantity Reqd. Description 1 2 DVD Headrest Unit 2 2 Headrest Extension Cables 3 1 Audio Interface Module 4 1 Audio Interface
More informationHarnessed Bypass Module Installation Instructions
Harnessed Bypass Module Installation Instructions The Original Secondary Air Injection System Bypass Kit Applicable for Toyota/Lexus Vehicles Introduction: A failure of any component of the Secondary Air
More informationINSTALLATION INSTRUCTIONS FOR THE TOMAHAWK ELECTRIC REVERSE
INSTALLATION INSTRUCTIONS FOR THE TOMAHAWK ELECTRIC REVERSE LAST UPDATED: April 2018 Thank you for choosing the Motor Trike Electric Reverse. We ask that you read the directions before you start and follow
More informationINSTALLATION INSTRUCTIONS Dual Catch Can Kit Subaru Turbo and STi Document# Support:
INSTALLATION INSTRUCTIONS Dual Catch Can Kit 02-14 Subaru Turbo and 2015+ STi Document# 19-0099 Support: info@radiumauto.com This document covers the installation of a Radium dual catch can kit for the
More information2015+ S550 MUSTANG Battery Relocation Kit WR-BTRYRELOKIT-LH WR-BTRYRELOKIT-RH
2015+ S550 MUSTANG Battery Relocation Kit WR-BTRYRELOKIT-LH WR-BTRYRELOKIT-RH The Watson Racing Battery Relocation Kit is NOT designed to protect you in the case of an accident, and therefore is INTENDED
More informationTOYOTA RAV TVIP V3
Section I Installation Preparation Part Number: 08586-4A872 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Status Monitor 3 1 Piezo Buzzer 4 1 V3
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationMustang One-Touch Convertible Top Module (2005+) - Installation Instructions
Mustang One-Touch Convertible Top Module (2005+) - Installation Instructions The below installation instructions work for the following products: Mustang One-Touch Convertible Top Module (2005+) Please
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Part # 751-FP2500 IMPORTANT INFORMATION This Jagg oil cooler must be installed following these instructions. Read the easy-to-follow instructions fully prior to starting the installation
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)
More informationBEFORE BEGINNING INSTALLATION
COMPLETE CHASSIS FUEL LINE KITS For 1996-2000 Honda Civic Equipped with B-Series Engine INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations
More informationThank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc.
Thank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc. We took much pride in putting together a fuel system that would deliver a maximum amount of fuel as simply as possible
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT 2017+ Honda Civic Type-R Document: 19-0193 Support: info@radiumauto.com 20-0424 PCV Catch Can Installation: Follow Steps 1-24 20-0425 CCV Catch Can Installation:
More informationINSTALLATION INSTRUCTIONS Oil Catch Can Kit BMW E46 3-Series/M3 Document# Support:
INSTALLATION INSTRUCTIONS Oil Catch Can Kit BMW E46 3-Series/M3 Document# 19-0055 Support: info@radiumauto.com Qty Description 1 Radium Engineering Anodized and Etched Catch Can Top 1 Radium Engineering
More informationLGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions
LGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative connections
More informationINSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support:
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: info@radiumauto.com These instructions are based on a vehicle with an OEM turbocharger
More informationINVISIHITCH. Hidden Hitch Receiver for. BMW X5 [F15] 2014 Current (all engines/suspension pkgs/trimlines, including M Sport line and Aero kit)
INVISIHITCH Hidden Hitch Receiver for BMW X5 [F15] 2014 Current (all engines/suspension pkgs/trimlines, including M Sport line and Aero kit) Capacity: 7,700 lbs. Towed Weight / 600 lbs Tongue Weight* *
More informationList of parts needed below. Tools needed
1 BMW 645 Coolant leak repair (Cap with Seal Repair and Expanding Coolant Pipe Installation w Pics) By Michael R. Brown (Estimated time to complete the job is 6-8 hrs) List of parts needed below. BMW PART
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More information