Assembly Instructions

Size: px
Start display at page:

Download "Assembly Instructions"

Transcription

1 Assembly Instructions Part Number Description Model Approx. Assembly Time Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing serious bodily injury or death. To prevent an accident, be sure that this accessory is properly and securely installed on your vehicle. If you cannot properly install this accessory yourself, have a professional installer, such as an authorized Kawasaki dealer, install it for you. Prior to each use, check to be sure the accessory is securely attached to the vehicle and periodically inspect the accessory for any required adjustment, wear, and damage. NOTE: Prior to installing this kit, the installation of Cab Enclosure ( ) is required Kawasaki Motors Corp., U.S.A. Page 1 of 11

2 Parts List: Ref. # Description Qty A01 Wiper Motor (110 ) 1 A02 Wiper Arm, (Adjustable ) 1 A03 Wiper Blade (20 ) 1 A04 Large Nylon Bushing 1 A05 1/4-20 x 5/8 Hex Screw 1 A06 1/4 Internal Tooth Lock Washer 1 A07 Small Nylon Bushing 1 A08 5/8 ID Rubber Washer 1 A09 5/8 ID Black Steel Washer 1 A10 1/4-20 Stainless Steel Cap Nut 1 A11 Short Wire Harness 1 A12 Long Wire Harness 1 A13 11 Black Wire Tie 3 A14 3/4 ID Rubber Grommet 2 A15 7/16 ID Rubber Grommet 1 Parts Diagram: A05 A06 A11 A07 A01 A12 A08 A09 A13 A04 A03 A14 A10 A15 A02 Page 2 of 11

3 NOTE: 1. If installing windshield wiper kit and cab enclosure at the same time proceed with installation instructions. 2. If cab enclosure has been previously installed proceed to Installation After Cab is Installed on page 8. Installation Instructions: 1. Park the vehicle on level ground, set the parking brake and turn off the ignition switch. 2. Lift seat forward to gain access to the battery. 3. Disconnect the negative battery terminal. 4. Drill the passengers side of dashboard with an 11/16 bit at location shown in diagram. Roughly 1-3/8 up from the fender and 1-13/16 in from the side of the hood. 5. Deburr both the inside and outside edges of the hole. Drill 11/16 Hole 1-13/ /8 6. Remove and save the (15) dart clips and (1) phillips head screw securing the hood panel and remove the hood. NOTE: If necessary, remove the grill assembly and the front bumper as described in the service manual. 7. Disconnect the ground wire (black wire with yellow stripe) from the back of the 12 volt outlet. Dart Clip Phillips head Screw 8. Disconnect the power wire (brown wire with red stripe) from the back of the 12 volt outlet. Page 3 of 11

4 9. Push on the piggyback terminal which is connected to the white wire of the supplied short wire harness (A11) to the copper tab with the (+) marking on the back of the 12V outlet. A Reconnect the power wire (brown wire with red stripe) to the piggyback terminal installed in the previous step. 11. Push on the piggyback terminal which is connected to the black wire of the supplied short wire harness (A11) to the tab with the (-) marking on the back of 12V outlet. A Reconnect the ground wire (black wire with yellow stripe) to the piggyback terminal installed in the previous step. 13. Route the loose end of the supplied short wire harness (A11) through the previously drilled hole on the passenger s side of the dashboard (step 4). A Secure short wire harness (A11) to vehicle chassis with 2 of the 3 wire ties (A13). NOTE: Orient the fuse holder to maintain future access from below the dashboard. A13 A11 Page 4 of 11

5 15. Position the hood back on vehicle. 16. Reinstall hood dart clips and phillips head screw. 17. Locate the right cab side frame and remove and discard the (2) plastic plugs and replace with the (2) supplied rubber grommets (A14). Right Side Frame NOTE: To avoid marring the paint when removing the plastic plugs, drive a screwdriver through the center of the plug and gently work out. 18. Thread long wire harness (A12) by feeding the bullet terminal end of harness through the upper most hole down and out through the lower hole in right side frame. NOTE: It may be helpful to use a wire or string as an aid to fish the harness down through the side frame tube. 19. Complete cab installation. 20. Connect the terminals coming through the hole drilled in dashboard to the ones hanging from the lower right side frame hole. A14 A12 Page 5 of 11

6 21. Feed the connection into the hole drilled into the dashboard. Make a slice in the supplied grommet (A15) wrap around wire and install into the hole in the dashboard. A14 A15 A Route the end of the long wire harness (A12) with the molded plug along the ROPS tube and down through the rubber grommet in the W/S support. A Use remaining wire tie (A13) to secure wire harness (A12) to ROPS cross-member. 24. Remove the plastic plugs from the windshield. A Assemble wiper motor to the inboard side of the windshield according to the diagram below. Align the wiper motor shaft with the larger of the two holes in windshield and wiper motor mounting ear with the smaller. A06 A05 A07 A01 A09 A08 A10 A04 A03 A02 Page 6 of 11

7 26. Connect wire harness (A12) to wiper motor (A01). 27. Reconnect negative battery terminal. 28. Turn motor on and off to cycle it back to the parked position. 29. Remove the screw and locknut from the wiper arm. 30. Insert the screw through the upper mounting hole in the wiper blade, then the wiper arm, and back through the wiper blade securing with the locknut. 31. Lift the locking tab on the underside of the wiper arm and extend the wiper arm to the desired length. The angle of the blade can be adjusted by loosening the small bolt on the top of the wiper arm. Locknut Angle Adjustment Bolt Length Adjustment Tab NOTE: Be sure the set screws found in the head of the wiper arm don t protrude into the knurled mating surface, loosen screws to avoid any interference when installing onto wiper motor shaft. 32. Press the wiper arm onto the shaft so that it is positioned at seven (7) o clock position. Turn the wiper motor on and test its operation. Adjust the arm sweep by turning the blade, adjusting the arm length, or removing the wiper arm off of the motor shaft and reinstalling it at a different position. 33. Make sure wiper arm is fully seated on wiper motor shaft. See adjacent photos for proper and improper wiper arm installation onto the splined shaft of the wiper motor. 34. Once wiper is fully adjusted, tighten the set screw on the wiper arm. The set screw location is noted in illustration at location A. NOTE: Properly installed. Notice finger is beyond the splined area. A02 A Page 7 of 11

8 NOTE: Improperly installed. Finger sitting on the splined area. NOTE: A mirror was used in both photos in order to clearly see and confirm the spring clip engagement. It is strongly suggested to double check the spring clip engagement using a mirror as illustrated. It may be necessary to lightly tap the arm with a rubber mallet to fully seat the arm. NOTICE To avoid breaking the windshield, support the wiper motor with your hand when tapping the arm. Wear safety glasses! Installation After Cab is Installed: NOTE: Unless otherwise specified, leave all cab enclosure hardware loose for later adjustment. 1. Park the vehicle on level ground, set the parking brake and turn off the ignition switch. 2. Lift seat forward to gain access to the battery and disconnect the negative terminal. 3. Remove and set aside the (2) 5/16-18 x 3/4 long button head, flanged cap screws & (2) 5/16-18 flange nyloc nuts retaining the windshield latch brackets to the right side frame. Page 8 of 11

9 4. Repeat step 3 for the left side. NOTE: Once the windshield hinge fasteners are removed during the next step the windshield assembly could fall! Proceed with caution. 5. With help from an assistant, remove and set aside the (4) 5/16-18 x 1-1/2 long flat head screws & (4) 5/16-18 flange nyloc nuts fastening the windshield assembly to the windshield support assembly. (Roof not shown for clarity). Windshield Assembly Windshield Support Assembly 6. With help from an assistant, remove the windshield assembly and place it aside. 7. Remove and set aside the (6) 5/16-18 x 3/4 long button head, flanged cap screws retaining the cowl assembly to the side frames. Cowl Assembly 8. Follow steps 4-18 of Installation Instructions starting on page 3 of this manual. 9. With help from an assistant place the cowl assembly in position over the vehicle s hood compressing the seal. Fasten cowl with (6) 5/16-18 x 3/4 long button head, flanged cap screws removed in step With help from an assistant, reinstall the windshield assembly and the (4) 5/16-18 x 1-1/2 long flat head screws & (4) 5/16-18 flange nyloc nuts removed during step 5. Page 9 of 11

10 11. Install the fasteners which were removed in step 3, (2) 5/16-18 x 3/4 long button head, flanged cap screws & (2) 5/16-18 flange nyloc nuts which retain the windshield latch brackets to the right side frame. 12. Repeat step 11 for the opposite side. 13. Close windshield latches and tighten windshield hinge fasteners then the windshield latch bracket bolts. NOTE: The windshield hinges are plastic components. Do not over tighten the 5/16-18 flat head screws. Torque to no more than: 9.5 N m (.97 kgf m, 7 ft lb). NOTE: The windshield hinges mount to the windshield support via slots. If need be, loosen hinge hardware & push windshield up or down in slots to attain better windshield to side frame seal. 14. Tighten all remaining 5/16-18 hardware, 25.5 N m (2.63 kgf m, 19 ft lb). 15. Complete the remainder of the installation by following steps of Installation Instructions starting on page 5 of this manual. Page 10 of 11

11 Service Parts Breakdown Page 11 of 11

Assembly Instructions

Assembly Instructions Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-049 Cab Enclosure MULE SX 3-4 Hours WARNING Improper installation of this accessory could result in an accident causing serious

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. C p. 1 of 21 INSTALLATION & OWNER S MANUAL F5205 HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INDUSTRIES, LLC. INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS KUBOTA GRAND L 40 SERIES HARD SIDED CAB ENCLOSURE (p/n 1KGL4AS) This Curtis Cab is designed and manufactured for use only as

More information

Installation instructions for Camaro/Firebird and Nova* Windshield Wiper Systems

Installation instructions for Camaro/Firebird and Nova* Windshield Wiper Systems Installation instructions for 1967-69 Camaro/Firebird and 1968-74 Nova* Windshield Wiper Systems The Raingear 1967-69 Camaro/Firebird and 1964-74 Nova wiper system is designed for ease of installation

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL 1 of 12 INSTALLATION & OWNER S MANUAL KAWASAKI MULE Pro FX-FXT CORNER FLASHER KIT p/n: 1KAPFXCFL Required Accessories: Fuse Panel: Kawasaki P/N: KAF080-076 Or Curtis P/N: 1KAPFXFP Approximate Installation

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. B, p. 1 of 25 INSTALLATION & OWNER S MANUAL POLARIS RANGER RCS (for models XP or HD) (for model years 2009-) cab without doors kit (p/n 1POLRCWD) cab with doors kit (p/n 1POLRC) doors only kit (p/n

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publication No. INSTALLATION INSTRUCTIONS WINCH MOUNT KIT P/N 08L77-HL3-A00 SXS700M4/M2 Honda Dealer: Please give a copy of these instructions to your customer. MII 14607 Issue Date

More information

RMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.

RMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com. RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Page 1 of 16 INSTALLATION & OWNER S MANUAL YAMAHA VIKING CAB KIT WITH HARD DOORS p/n: 1YAMVK fits model years 2014- (fits Yanmar Bull model years 2017-) NOTE: By design, the doors are made to not be removable!

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 3000 SERIES (4200/4300/4400) (4210/4310/4410) & (3120/3320/3520/3720) HARD SIDED CAB ENCLOSURE (p/n 1JD3520AS) SOFT SIDED CAB ENCLOSURE

More information

2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware

2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware Owner s Manual Model: Polaris RZR * 2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. A, p. 1 of 6 INSTALLATION & OWNER S MANUAL YANMAR SA-424 WINDSHIELD KIT P/N 1CYSA4WS FITS SA-424 TRACTORS WITH 4 POST ROPS The contents of this envelope are the property of the owner. Be sure to leave

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS MASSEY FERGUSON TGX SERIES SOFT SIDED CAB ENCLOSURE (p/n MFTGXSS) This Curtis Cab is designed and manufactured for use only as reasonable weather

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publication No. MII 15249 WINCH MOUNT KIT P/N 08L70-HL3-A41 SXS700/M4/M2 Issue Date September 2015 PARTS LIST No. Description Qty (1) Winch bracket 1 (2)

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL p. 1 of 15 INSTALLATION & OWNER S MANUAL Polaris Ranger 500-800 PathPro SS Cab (fits 2010 - current) (p/n: 1POLRFS1) The contents of this envelope are the property of the owner. Be sure to leave with the

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS FOR E-Z-GO MPT BALL CAGE (p/n 72685-G01) The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation

More information

Installation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)

Installation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf) Page 1 This tutorial is provided as a courtesy by ECS Tuning. Service Procedure Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. E p. of 3 INSTALLATION & OWNER S MANUAL V446 Front Cab Kit and V446 Rear Cab Kit for RTV 40 INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave

More information

Cab Kit Installation Instructions

Cab Kit Installation Instructions Low Speed Vehicles (LSV) Electric Vehicles: Carryall Carryall 6 Cab Kit Installation Instructions Publication 050770 These instructions apply to the following kit: 0670 Edition Code 008E09D GENERAL INFORMATION

More information

REARVIEW MIRROR AND BACKUP CAMERA KIT

REARVIEW MIRROR AND BACKUP CAMERA KIT REARVIEW MIRROR AND BACKUP CAMERA KIT P/N 2881483 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL p. 1 of 13 INSTALLATION & OWNER S MANUAL Polaris Ranger 400-EV PathPro SS Cab (fits 2010 - current) (p/n: 1PRG400FS) The contents of this envelope are the property of the owner. Be sure to leave with the

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. S 1998 CIVIC 2/3/4-DOOR All 18767 Issue Date SEP 1997 PARTS LIST Fog Light Kit: P/N 08V31-S01-100 Right fog light (marked R ) Fuse label

More information

IT IS IMPORTANT THAT YOU OBTAIN THE CORRECT INFORMATION FOR YOUR VEHICLE, OR DAMAGE TO THE WIRING SYSTEM COULD OCCUR.

IT IS IMPORTANT THAT YOU OBTAIN THE CORRECT INFORMATION FOR YOUR VEHICLE, OR DAMAGE TO THE WIRING SYSTEM COULD OCCUR. Instructions for Universal Harness PRINT THESE INSTUCTIONS Gentex Mirror Installation Instructions Provided by www.rearviewautomirrors.com These instructions have been prepared to provide you with details

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Electronic Tailgate Lock Kit Nissan Titan 999M2-W3005 KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Electronic

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. A, p. of 0 INSTALLATION & OWNER S MANUAL MASSEY FERGUSON GC2400 cab kit p/n MFGC2400 Installation Instructions The contents of this envelope are the property of the owner. Be sure to leave with the

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 CAB KIT (p/n: KAF40-005WA and KAF40-005BA) NOTE: Hard sided doors are sold separately. This manual is the property of the owner.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit

More information

RIM Hood For Aeromaster Bodies

RIM Hood For Aeromaster Bodies RIM Hood For Aeromaster Bodies Service Guide WARNING: Hood should be opened by releasing the hold-down straps, lifting the hood, and engaging the prop rod. Be sure prop rod is properly engaged before working

More information

Ref Qty Part Description Part Number -1- Kit ( ) Contents:

Ref Qty Part Description Part Number -1- Kit ( ) Contents: REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publication No. INSTALLATION INSTRUCTIONS HORN MOUNT P/N 08Z77-HL4-A00 SXS1000M3/M3P/M5D/M5P Honda Dealer: Please give a copy of these instructions to your customer. MII 15262 Issue

More information

It is strongly recommended that this kit be installed by an authorized Polaris dealer.

It is strongly recommended that this kit be installed by an authorized Polaris dealer. EPS STEERING KIT P/N 2879970 APPLICATION RANGER 570 AND RANGER ETX IMPORTANT It is strongly recommended that this kit be installed by an authorized Polaris dealer. BEFORE YOU BEGIN Read these instructions

More information

WINDSHIELD WIPER KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS NOTE. Instr Rev 02 06/15 Page 1 of 7

WINDSHIELD WIPER KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS NOTE. Instr Rev 02 06/15 Page 1 of 7 WINDSHIELD WIPER KIT P/N 2879968 APPLICATION RANGER 570, RANGER ETX AND RANGER EV Polaris does not recommend use of this kit with Tip-Out Windshield PN 2880442. BEFORE YOU BEGIN Read these instructions

More information

TOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation

TOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation Preparation Part Number: PT413-42130 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 20 Cable Tie 2 2 Scotchlok 3 2 Foam Pad

More information

P/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or

P/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Pg. 1 of 14 INSTALLATION & OWNER S MANUAL John Deere Gator XUV 825i S4 Cab (p/n: 1GTRXUV4 Steel Cab with Doors) The contents of this envelope are the property of the owner. Be sure to leave with the owner

More information

Part Number: TTU-BGB14-DRL TTU-BGP14-DRL

Part Number: TTU-BGB14-DRL TTU-BGP14-DRL 11/15/16 TOYOTA TUNDRA 2014-17 Billet Grille w/led DRL Part Number: TTU-BGB14-DRL TTU-BGP14-DRL Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Switch 4 1 User Card 5 2 Hardware

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. R p. 1 of 16 INSTALLATION & OWNER S MANUAL V4211 HARD SIDED CAB KIT and/or V4275 CAMO HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner.

More information

Wiper Motor Windshield Frame Mount Marinco-500. Installation Instructions

Wiper Motor Windshield Frame Mount Marinco-500. Installation Instructions Wiper Motor Windshield Frame Mount Marinco-500 Installation Instructions Wiper Motor Windshield Frame Mount Marinco-500 Tools (Not Included): Phillips head screwdriver 17 mm or small adjustable wrench

More information

VISOR AUDIO KIT P/N , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.

VISOR AUDIO KIT P/N , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com. VISOR AUDIO KIT P/N 2882888, 2882891 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain

More information

Gentex Homelink Installation Instructions

Gentex Homelink Installation Instructions Gentex Homelink Installation Instructions Kit Contents: Item Qty Part Description 1 Number GENK-41 NVS Homelink Mirror GENK-42 NVS Homelink w/mood lights 1 of the GENK-45 NVS Homelink w/compass following

More information

2011-up Polaris RZR 800* Cab Enclosure Kit. Caution: Before using this product, read this manual and follow all safety instructions.

2011-up Polaris RZR 800* Cab Enclosure Kit. Caution: Before using this product, read this manual and follow all safety instructions. Owner s Manual Model: Polaris RZR * 2011-up Polaris RZR 800* Cab Enclosure Kit Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions Kit Contents

More information

AUDIO KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.

AUDIO KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com. AUDIO KIT P/N 2882696 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation

More information

2015 Ford F150 Rear Bumper w/ LED

2015 Ford F150 Rear Bumper w/ LED 2015 Ford F150 Bumper w/ LED T527990 T527991 PARTS LIST: 1 Bumper Assembly 4 12mm Lock Washers 2 Mounting Brackets 6 12 mm Nylon Lock Nuts 4 Sensor Hole Plugs 8 4mm x 10mm Button Head Bolts 2 Plastic Plugs

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. L p. 1 of 16 INSTALLATION & OWNER S MANUAL V4262 CAMO (SOFT SIDED) CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner

More information

RANGER 900 POWER STEERING KIT

RANGER 900 POWER STEERING KIT RANGER 900 POWER STEERING KIT P/N 2880083 APPLICATION MY14 AND NEWER RANGER XP 900 MODELS IMPORTANT It is strongly recommended that this kit be installed by an authorized Polaris dealer. NOTE Use of this

More information

Gentex by VOXX Corporation Installation Instructions

Gentex by VOXX Corporation Installation Instructions KIT CONTENTS: Item Qty Part Number Description 1 1: ADVGEN20A 7 Pin Auto-Dimming Mirror with Compass and Temperature 2 1 Gentex by VOXX Corporation Installation Instructions Contact VOXX Customer Service

More information

WINCH MOUNT KIT FOR POLARIS RANGER P/N ASSEMBLY / OWNERS MANUAL. Application WINCH KIT NO. 25-9xxx

WINCH MOUNT KIT FOR POLARIS RANGER P/N ASSEMBLY / OWNERS MANUAL. Application WINCH KIT NO. 25-9xxx WINCH MOUNT KIT FOR POLARIS RANGER P/N 25-3370 ASSEMBLY / OWNERS MANUAL Application WINCH KIT NO. 25-9xxx Before you begin, please read these instructions and check to be sure all parts and tools are accounted

More information

TOYOTA im INTERIOR LIGHT KIT Preparation

TOYOTA im INTERIOR LIGHT KIT Preparation Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Accessory Hands Free Link Application 2008 ACCORD 2 AND 4-DOOR Publications No. AII 38281 Issue Date NOV 2007 PARTS LIST Attachment Kit P/N 08E02-TA0-100 trim retainer

More information

RSA FJ CRUISER LONG RANGE TANK GET ORGANIZED. INSTALL TIME: 1.5 hours

RSA FJ CRUISER LONG RANGE TANK GET ORGANIZED. INSTALL TIME: 1.5 hours FJ CRUISER LONG RANGE TANK RSA FTTJ001 INSTALL TIME: 1.5 hours 1 GET ORGANIZED you will need: a 1 and 15 wrench a 10, 1, 15 and 7 socket, and ratchet with an extension a craft/stanley knife a hack saw

More information

REAR ROOF SPEAKER KIT

REAR ROOF SPEAKER KIT REAR ROOF SPEAKER KIT P/N 2882876 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain

More information

Installation Instructions

Installation Instructions Parts Installation Instructions DESCRIPTION PART # QTY A Alignment Tab PN ESB101 1 B Drill Guide PN ESB102 1 C Actuator Cable Assembly PN ESB103 1 C1 72 Actuator Cable 1 C2 5/16 Jam Nut 1 C3 Star Washer

More information

JOHN DEERE GATOR SWITCH PANEL INSTRUCTIONS FITS 1GTRXUV2 AND 1GTRXUV4 CABS (p/n: 1XUVSP)

JOHN DEERE GATOR SWITCH PANEL INSTRUCTIONS FITS 1GTRXUV2 AND 1GTRXUV4 CABS (p/n: 1XUVSP) P. 1 of 5 JOHN DEERE GATOR SWITCH PANEL INSTRUCTIONS FITS 1GTRXUV2 AND 1GTRXUV4 CABS (p/n: 1XUVSP) Note: Harness Extension Kit Required for 4 Passenger (p/n: 1XUV4WHEK) This manual is the property of the

More information

RZR WINCH KIT KIT P/N

RZR WINCH KIT KIT P/N RZR WINCH KIT KIT P/N 2878787; 2879334 Application All RZR Models except RZR XP Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08V31-S0X-100 1999-2001 ODYSSEY AII 20677 Issue Date AUG 1999 PARTS LIST 2 Fog lights Switch Fuse label Right bracket Relay B, 4-pin

More information

Detroit Speed, Inc. Selecta-Speed Wiper Kit Corvette P/N:

Detroit Speed, Inc. Selecta-Speed Wiper Kit Corvette P/N: Detroit Speed, Inc. Selecta-Speed Wiper Kit 1963-67 Corvette P/N: 121620 A downpour of rain will no longer hinder your ability to clearly see the road. The Detroit Speed Selecta-Speed Wiper Kit provides

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publication No. INSTALLATION INSTRUCTIONS WINCH MOUNT P/N 08L73-HL4-F01 After 16 SXS1000M3/M3P/M3LE SXS1000M5P/M5D/M5LE MII 16083 Issue Date February 2017 PARTS LIST No. Description

More information

Instructions for 2-row monitoring only

Instructions for 2-row monitoring only Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only CAUTION: Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect

More information

POLY TIP-DOWN WINDSHIELD KIT

POLY TIP-DOWN WINDSHIELD KIT POLY TIP-DOWN WINDSHIELD KIT P/N 2881919 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08E49-S2A-100 2004 S2000 AII 26325 Issue Date OCT 2003 PARTS LIST Hood switch harness TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory ENGINE BLOCK P/N 08T44-SWA-1A0 Application 2012 CIVIC 4-DOOR Si Publications No. AII 45627 Issue Date APRIL 2011 PARTS LIST Engine block heater Aluminum washer Heater

More information

Turn Signal / Horn Kit PN 7101 by All years Polaris RZR 1000 and RZR 900, 900-4, 900 trail, 900S and 900XC STOP - THIS KIT IS DESIGNED

Turn Signal / Horn Kit PN 7101 by All years Polaris RZR 1000 and RZR 900, 900-4, 900 trail, 900S and 900XC STOP - THIS KIT IS DESIGNED All years Polaris RZR 1000 and 1000-4 2015 RZR 900, 900-4, 900 trail, 900S and 900XC STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR ALL YEAR AND MODEL POLARIS RZR 1000 AND 1000-4. ALSO THE 2015 POLARIS RZR

More information

TOYOTA PRIUS FOG LIGHT (Halogen or LED)

TOYOTA PRIUS FOG LIGHT (Halogen or LED) Part Number: TPR-413 / TPR-813 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 1 Lower Grill 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness Bag Hardware Bag Contents Item

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Versa (2012) PART NUMBER: 999F3 AW008 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description

More information

SCION tc FOG LIGHT. Part Number: STC-312 / STC-812

SCION tc FOG LIGHT. Part Number: STC-312 / STC-812 SCION tc 2011-2013 FOG LIGHT Part Number: STC-312 / STC-812 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Fog Light bezels 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2012 ODYSSEY Publications No. AII 46755 Issue Date SEP 2011 PARTS LIST Trailer Hitch Kit P/N 08L92-TK8-100 Trailer Hitch Harness Kit P/N 08L91-TK8-100

More information

Instructions for 2-row monitoring only

Instructions for 2-row monitoring only Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect installation

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE GATOR HPX and/or XUV HARD SIDED CAB ENCLOSURE (p/n: 1GTR44AS) SOFT SIDED CAB ENCLOSURE (p/n: 1GTR44SS) 111 HIGGINS STREET, WORCESTER,

More information

Air Conditioner for M915 A0/A1 Truck

Air Conditioner for M915 A0/A1 Truck RD-2-4530-0 Air Conditioner for M915 A0/A1 Truck INSTALLATION INSTRUCTIONS Install refrigerant compressor per instructions provided with compressor mount kit. CAUTION: Edges of sheet metal can be sharp!

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior

More information

LGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions

LGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions LGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative connections

More information

Depress each tab as you pull the bezel off. The bezels are tight. L.H. shown.

Depress each tab as you pull the bezel off. The bezels are tight. L.H. shown. 2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2011 ODYSSEY Publications No. AII 43937 Issue Date SEP 2010 PARTS LIST Trailer Hitch Kit P/N 08L92-TK8-100 Trailer Hitch Harness Kit P/N 08L91-TK8-100

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2011 ODYSSEY Publications No. AII 43937 Issue Date SEP 2010 PARTS LIST Trailer Hitch Kit P/N 08L92-TK8-100 Trailer Hitch Harness Kit P/N 08L91-TK8-100

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 TRANS 4 FRONT CAB KIT (p/n: KAF40T-001WA and p/n: KAF40T-001BA) NOTE: Hard sided doors, soft sided doors, and rear cab are sold

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC

More information

MOTOALLIANCE WINCH MOUNT

MOTOALLIANCE WINCH MOUNT , / 1-866-527-7637 www.motoalliance.com MOTOALLIANCE WINCH MOUNT Polaris RZR Thank you for purchasing our MotoAlliance winch mount(s). You now own a premium custom winch mount to allow you to use your

More information

POLY TIP-DOWN WINDSHIELD KIT

POLY TIP-DOWN WINDSHIELD KIT POLY TIP-DOWN WINDSHIELD KIT P/N 2883261 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please

More information

ROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8

ROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8 Installation Instructions P/N: 422128 (R1318-5231LITE) Fastback GT Convertible GT V8 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH ROUSH Active IO Exhaust Installation Instructions P/N: 422128

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL p. 1 of 15 INSTALLATION & OWNER S MANUAL YANMAR Sc2450 cab kit with hard doors and soft rear curtain Curtis p/n: 1CYSC2450AS The contents of this envelope are the property of the owner. Be sure to leave

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory ACCESSORY HANDSFREELINK Application 2010 ACCORD 2 AND 4-DOOR Publications No. AII 42231 Issue Date AUG 2009 PARTS LIST HFL retainer HFL Attachment Kit P/N 08E02-TA0-100

More information

2-row and All-row systems included.

2-row and All-row systems included. Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown above correspond

More information

SCION xb 2004 SECURITY (V5) Section I Installation Preparation. Part Number:

SCION xb 2004 SECURITY (V5) Section I Installation Preparation. Part Number: Section I Installation Preparation Part Number: 08586 52960 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Mounting Bracket 3 1 GBS ECU 4 1 Security

More information

WARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag.

WARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag. Part Number: 36030 Product Description: BULL BAR WINCH TYPE Suited to vehicle/s: CHEVROLET C/K 500-3500 988-998 YEAR MODEL RANGE AND Warn 9,500-5,000lb WINCHES WARNING REGARDING VEHICLES EQUIPPED WITH

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL ENGINE STARTER Application 2010 CR-V Publications No. AII 42612-42916 Issue Date OCT 2009 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-101B

More information

TOYOTA PRIUS PLUS LOWERING SPRINGS Preparation

TOYOTA PRIUS PLUS LOWERING SPRINGS Preparation Preparation Part Number: PTR07-47100 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 2 Nut 4 1 Instructions Hardware Bag Contents Item # Quantity Reqd. Description 1 2

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 12035 SYSTEM 2012 RIDGELINE Issue Date NOV 2011 PARTS LIST Security System Attachment Kit: P/N 08E55-SJC-101 Flange bolt Unit bracket

More information

DOOR KIT P/N , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.

DOOR KIT P/N , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com. DOOR KIT P/N 2882561, 2882562 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Accessory Hands Free Link Application 2009 ACCORD 2 AND 4-DOOR Publications No. AII 40055 Issue Date JULY 2008 PARTS LIST HFL Attachment Kit P/N 08E02-TA0-100 HFL trim

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Aftermarket Display 2007-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9560) Kit Contents: Chassis Harness with RCA (Note: In some cases a RCA

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab Diesel 2011 and newer Part Number: 75147-15 Chevy Silverado/GMC Sierra

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publication No. WINCH MOUNT P/N 08L74-HR3-A20 After 13 TRX420 (All except TRX420FA/FPA) After 13 TRX500 (All except TRX500FA/FPA) MII 15067 Issue Date Revised:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)

More information

Part Number: TAV-713 TOYOTA AVALON LED DRL

Part Number: TAV-713 TOYOTA AVALON LED DRL Part Number: TAV-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion pad 6 1 Switch 7 2 Drill Jigs Hardware Bag Contents

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. C, p. 1 of 18 INSTALLATION & OWNER S MANUAL KUBOTA RTV 400 CAB (Not for use on RTV 500) These instructions are for installation of the complete cab as well as the modular components. DESCRIPTION:

More information

TOYOTA TACOMA EC REARVIEW MIRROR Preparation

TOYOTA TACOMA EC REARVIEW MIRROR Preparation Preparation Part Number: PT374-35052 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 1 T-tap Connectors,

More information

TOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure

TOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6

More information