Automotive Data Solutions Inc. AVAILABLE FOR : ADS-TB. Rev. Date: May 17, 2017 Doc. No.: ##39456##

Transcription

1 Automotive Data Solutions Inc. INSTALL GUIDE ADS-TB-FM-EN FM AVAILABLE FOR : ADS-TB Rev. Date: May 7, 07 Doc. No.: ##3956## U.S. PATENT NO. 8,856,780 PLEASE VISIT FOR COMPLETE PRODUCT DETAILS The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 07 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.

2 Page of 5 ADS-TB-FM-EN Doc. No.: ##3956## INSTALL TYPE SELECTION MaKe Ford JaGUar ModeL year InsTaLL Type number of Keys Contour Crown Victoria 98-0 Crown Victoria E-Series 08- Edge 07-0 Escape 0- Escape Hybrid 05- Excursion Expedition 99-0 Expedition 0- Explorer 98-0 Explorer 0-0 Explorer Sport Trac 0 Explorer Sport Trac 0-05 Explorer Sport Trac 07-0 F F50 0- F-Series Super Duty 08-0 Fiesta -3 Five Hundred Flex 09- Focus 00- Freestar 0-07 Freestyle Fusion 06- Fusion Hybrid 0- GT Mustang 99-0 Mustang 05- Ranger 99-0* Ranger **0-0 Taurus Standard key Taurus Standard key 00- Taurus X 08-0 Thunderbird Transit Connect 0-3 Windstar 99-0* Windstar **0-03 S-Type X-Type * Vehicles manufactured before 07//000 **Vehicles manufactured after 07//000 VpG MerCUry MaZda LInCoLn MaKe ModeL year InsTaLL Type number of Keys Aviator Blackwood 0-03 Continental 98-0 LS Mark LT MKS w/o smartkey 09- MKX 07-0 MKZ 07- Navigator 99-0 Navigator 0- Town Car 98-0 Town Car 03- Zephyr w/o smartkey w/o smartkey 09-3 B-Series 99-0* B-Series **0-0 CX7 07- CX9 07- MX Tribute 0- Cougar 99-0 Grand Marquis 98-0 Grand Marquis 03-0 Marauder 03-0 Mariner 05-0 Mariner Hybrid 06-0 Milan 06-0 Montego Monterey 0-07 Mountaineer 98-0 Mountaineer 0-0 Mystique Sable Sable Sable MV- -3 NOTE I II IMPORTANT: some vehicles only require key for programming. KLON service is avaible with the TB-FM solution for vehicles that require keys for programming.

3 Page 3 of 5 ADS-TB-FM-EN Doc. No.: ##3956## FM ADVANCED FIRMWARE KNOWLEDGE BASE INSTALL TYPE : The installation type is a result of long term field testing with logic analyzers and aftermarket products permanently installed in multiple vehicles. During the researches, it s been possible to identify strong bouncing frequencies received through the immobilizer antenna during remote start due to many different types of products. The most common products to affect the immobilizer communication are; Blue Tooth devices, cellular hands free kits, cell phones, wireless internet, Two way aftermarket alarm/starters (depending on RF timing), remaining key in the ignition barrel are all examples of interfering devices. Our researches concluded that the PATS immobilizers systems using the D type connector were a lot more sensitive to external RF than any other PATS receivers. For this reason, from now on, we recommend you to use the install type on any vehicle equipped with the D type connector PATS immobilizer. Alto we list only the D type vehicles for type, it is recommended to use the type installation method for vehicles equipped with many RF devices or if the vehicle owner intends to remote start the vehicle with a key remaining in the ignition barrel. (RF collisions may result into intermittent remote start failure since the module protection will interrupt communications upon collision detection to avoid sending any corrupted informations to the vehicle) INSTALL TYPE 3: On only few vehicles the PATS immobilizer module is powered on constant Volts instead of being powered on ignition. Since all the other vehicles PATS systems are powered on ignition, the ignition signal is used to synchronize the immobilizer challenge/communication. On the PATS systems powered on Volts, a learning error will occur due to the wrong communication timing. This will prevent the module from learning the vehicle and the module LED will start blinking Red. We recommend to correct the vehicle circuitry by changing the PATS power source to an Ignition power source instead of constant Volts. A fuse should be used as recommended in the install schematic. The vehicle will properly start using a key or the remote starter once this modification is performed to adapt to the normal PATS initialization timings. The modification have to be secured and left permanent in the vehicle ADVANCED DIAGNOSTIC Did you know the Firmware is monitoring the entire module learning process and records everything in its EEPROM? Exactly, as soon the module is connected to the vehicle it starts monitoring and recording all its I/O s (same as an airplane black box). The information can be extracted from the module and sent to your technical support team for advanced debugging at any required time. The information recorded is: Install Type st key code st ignition cycle ON position timing st ignition cycle OFF position timing nd key code nd ignition ON position timing nd ignition OFF position timing Any immobilizer communication collision RS3 communications Vehicle unlocking its programming Module key code sent to vehicle and validated or rejected Spikes on the ignition wire Cloned keys detection Protected memory buffer for module key code recovery even after module is re-flashed and a factory reset is been performed. / inversion detection and protection Installation mode, firmware, hardware informations Advanced recording routine for emergency key code cracking Complete encryption recording and advanced anti-collision protection THE ADVANTAGES: The FM Firmware is the most advanced TI solution available yet. The module EEPROM protected area ensure you will never use more than one key memory bank in the vehicle ECU. If it s ever needed to reset and reprogram a module due to a system upgrade, the FM Firmware will give you the ability to proceed without the need of two vehicle keys. The ADVANCED DIAGNOSTIC feature is a real install asset as it permit any technical support staff to see exactly what happens in the vehicle. The information retrieved is an undisputed time saver and the quickest solution finder available in the industry.

4 Page of 5 ADS-TB-FM-EN Doc. No.: ##3956## TYPE - WIRE CROSS REFERENCE CHART - OF 3 rx ConneCTor MaKe ModeL year Ford LoCaTIon Contour Gray/Orange White/LtGreen B Crown Victoria 98-0 White/LtGreen 3 Gray/Orange A Crown Victoria 03-0 White/LtGreen 3 Gray/Orange C Crown Victoria White/LtGreen Gray/Orange E E-Series 08 White/LtGreen 3 Gray/Orange C E-Series 09- Yellow/Orange 3 Purple/Gray C Edge Purple/Gray Yellow/Orange E Escape / Hybrid Brown/Orange Red/Black B Escape / Hybrid 08-3 Yellow/Orange Purple/Gray E Excursion 00-0/03* White/LtGreen 3 Gray/Orange A Excursion 03**/0-05 White/LtGreen 3 Gray/Orange C Expedition 99-0 White/LtGreen 3 Gray/Orange A Expedition White/LtGreen Gray/Orange B Expedition 07-3 Purple/Brown Blue/Gray E Explorer 98-00/0* White/LtGreen 3 Gray/Orange A Explorer (dr) 0**/0-03 White/LtGreen 3 Gray/Orange C Explorer White/LtGreen Gray/Orange B Explorer Yellow/Orange Purple/Gray E Explorer Sport Trac 0* White/LtGreen 3 Gray/Orange A Explorer Sport Trac 0**/0-05 White/LtGreen 3 Gray/Orange C Explorer Sport Trac Yellow/Orange Purple/Gray E F White/LtGreen 3 Gray/Orange A F White/LtGreen 3 Gray/Orange C F White/LtGreen Gray/Orange B F Purple/Gray*** Yellow/Orange*** E F-Series Super Duty Yellow/Orange Purple/Gray E Fiesta -3 3 Yellow/Orange Purple/Gray E Five Hundred White/LtGreen Gray/Orange E Flex 09-3 Yellow/Orange Purple/Gray E Focus Gray/Orange White/Green B Focus 08- Purple/Gray*** 3 Yellow/Orange*** E Freestar 0-07 White/LtGreen 3 Gray/Orange C Freestyle White/LtGreen Gray/Orange E Fusion 06/07* 3 Purple/Gray Yellow/Orange E Fusion 07**/08-3 Yellow/Orange Purple/Gray E GT White/Orange Brown/Orange B Mustang 99-0 White/LtGreen 3 Gray/Orange A Mustang 03-0 White/LtGreen 3 Gray/Orange C Mustang White/LtGreen Gray/Orange E Mustang 0-3 Purple/Gray Yellow/Red E Ranger White/LtGreen 3 Gray/Orange A Ranger 0-06 White/LtGreen 3 Gray/Orange C Ranger 07-0 Purple/Brown 3 Blue/Gray C Taurus 98-0 Brown/Orange 3 Red/Black A Taurus 0 Gray/Red 3 Brown/Yellow A Taurus 03 Brown/Yellow 3 Gray/Red C * early production ** LaTe production *** s May Vary BUT pin out Is CorreCT

5 Page 5 of 5 ADS-TB-FM-EN Doc. No.: ##3956## TYPE - WIRE CROSS REFERENCE CHART - OF 3 rx ConneCTor MaKe ModeL year MerCUry MaZda LInCoLn Ford LoCaTIon Taurus 0-07 White/LtGreen 3 Gray/Orange C Taurus 08-3 Yellow/Orange Purple/Gray E Taurus X Yellow/Orange Purple/Gray E Transit Connect Gray/Orange White/Green E Windstar 99-0 White/LtGreen 3 Gray/Orange A Windstar 03 White/LtGreen 3 Gray/Orange C Aviator White/LtGreen Gray/Orange B Blackwood 0 White/LtGreen 3 Gray/Orange A Blackwood 03 White/LtGreen 3 Gray/Orange C Continental 98* 3 White/LtGreen Gray/Orange A Continental 98**/99-0 White/LtGreen 3 Gray/Orange A Mark LT White/LtGreen Gray/Orange B MKS (w/o smartkey) 09-3 Yellow/Orange Purple/Gray E MKX Purple/Gray Yellow/Orange E MKZ 07* 3 Purple/Gray Yellow/Orange E MKZ 07**/08-3 Yellow/Orange Purple/Gray E Navigator 99-0 White/LtGreen 3 Gray/Orange A Navigator White/LtGreen Gray/Orange B Navigator 07-3 Purple/Brown Blue/Gray E Town Car 98-0 White/LtGreen 3 Gray/Orange A Town Car 03-0 White/LtGreen 3 Gray/Orange C Town Car 05-3 White/LtGreen Gray/Orange E Zephyr 06 3 Purple/Gray Yellow/Orange E - Gray 3 Green H B-Series White/LtGreen 3 Gray/Orange A B-Series 0-06 White/LtGreen 3 Gray/Orange C B-Series 07-0 Purple/Brown 3 Blue/Gray C Tribute Brown/Orange Red/Black B Tribute 08-3 Yellow/Orange Purple/Gray E Cougar Gray/Orange White/Green B Grand Marquis 98-0 White/LtGreen 3 Gray/Orange A Grand Marquis 03-0 White/LtGreen 3 Gray/Orange C Grand Marquis White/LtGreen Gray/Orange E Marauder 03-0 White/LtGreen 3 Gray/Orange C Mariner / Hybrid Brown/Orange Red/Black B Mariner / Hybrid Yellow/Orange Purple/Gray E Milan 06/07* 3 Purple/Gray Yellow/Orange E Milan 07**/ Yellow/Orange Purple/Gray E Montego White/LtGreen Gray/Orange E Monterey 0-07 White/LtGreen 3 Gray/Orange C Mountaineer 98-0 White/LtGreen 3 Gray/Orange A Mountaineer White/LtGreen Gray/Orange B Mountaineer Yellow/Orange Purple/Gray E Mystique Gray/Orange White/LtGreen B Sable 98-0 Brown/Orange 3 Red/Black A * early production ** LaTe production *** s May Vary BUT pin out Is CorreCT

6 Page 6 of 5 ADS-TB-FM-EN Doc. No.: ##3956## TYPE - WIRE CROSS REFERENCE CHART - 3 OF 3 rx ConneCTor MaKe MerCUry ModeL VpG year LoCaTIon Sable 0 Gray/Red 3 Brown/Yellow A Sable 03 Brown/Yellow 3 Gray/Red C Sable 0-05 White/LtGreen 3 Gray/Orange C Sable Yellow/Orange Purple/Gray E MV- -3 Yellow/Orange 3 Purple/Gray C

7 IGN INSTALL GUIDE Page 7 of 5 ADS-TB-FM-EN Doc. No.: ##3956## TYPE - WIRING DIAGRAM STANDARD VOLT, AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. CONNECTOR A - WHITE FOUND 8 INCHES LOWER ON PATS HARNESS CONNECTOR B - GREEN CONNECTOR C - GREEN FOUND 8 INCHES LOWER ON PATS HARNESS CONNECTOR D- WHITE CONNECTOR E - BLACK CONNECTOR F - WHITE REMOTE STARTER CONNECTOR H X Y V (+) (-) WHEN RUNNING (-) OUTPUT DATA MODE LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARDWIRE MODE CONNECT TO THE VEHICLE MAIN IGNITION. DO NOT CONNECT AT THE PATS MODULE. DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE - BLACK V (+) - RED IGNITION (+) INPUT - PINK (NC) PINK/BLACK (NC) ORANGE (NC) GRAY/YELLOW ECM - GRAY/RED (NC) GREEN/YELLOW ECM - GREEN/RED (NC) BLUE/YELLOW (NC) BLUE/RED WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC)

8 Page 8 of 5 ADS-TB-FM-EN Doc. No.: ##3956## TYPE - WIRE CROSS REFERENCE CHART - OF rx ConneCTor MaKe ModeL MaZda year LoCaTIon Gray/Orange White/LtGreen D 3 (w/o smartkey) 0-3 LtBlue Blue D Green Pink/Black D 5-7 LtBlue/Orange Gray D 6 (w/o smartkey) Green Orange/LtBlue D 6 (with smartkey) Yellow/Green Gray D 6 (w/o smartkey) 09-3 Gray/Orange 3 White/LtGreen F CX7 07- Gray/Orange White/LtGreen D CX9 07- Blue/Yellow Blue/Orange D MX-5 (w/o smartkey) 06- Yellow/Black LtBlue/Orange D MX-5 (with smartkey) 06- Gray/LtBlue Purple D LtBlue/Orange Yellow/Black D

9 Page 9 of 5 ADS-TB-FM-EN Doc. No.: ##3956## TYPE - WIRING DIAGRAM STANDARD VOLT, AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. CONNECTOR A - WHITE FOUND 8 INCHES LOWER ON PATS HARNESS CONNECTOR B - GREEN CONNECTOR C - GREEN FOUND 8 INCHES LOWER ON PATS HARNESS CONNECTOR D- WHITE CONNECTOR E - BLACK CONNECTOR F - WHITE REMOTE STARTER X Y V (+) (-) WHEN RUNNING (-) OUTPUT DATA MODE LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARDWIRE MODE CONNECT TO THE VEHICLE MAIN IGNITION. DO NOT CONNECT AT THE PATS MODULE. DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE - BLACK V (+) - RED IGNITION (+) INPUT - PINK (NC) PINK/BLACK (NC) ORANGE (NC) GRAY/YELLOW ECM - GRAY/RED (NC) GREEN/YELLOW VEHICLE SIDE - GREEN/RED (NC) BLUE/YELLOW (NC) BLUE/RED WHITE/BLACK - CONNECTOR SIDE WHITE/RED - VEHICLE SIDE WHITE (NC)

10 Page 0 of 5 ADS-TB-FM-EN Doc. No.: ##3956## TYPE 3 - WIRE CROSS REFERENCE CHART - OF rx pats power ConneCTor Ford MaKe JaGUar LInCoLn ModeL year LoCaTIon Thunderbird White/Red Gray/Red Orange/Blue B S-Type White/Red Gray/Red Orange/Blue B S-Type White/Red Yellow/Red Brown/Green B X-Type White/Green Orange Green B LS White/Red Gray/Red Orange/Blue B

11 Page of 5 ADS-TB-FM-EN Doc. No.: ##3956## TYPE 3 - WIRING DIAGRAM STANDARD VOLT, AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. CONNECTOR B - GREEN 3 POWER REMOTE STARTER SECURE AND INSULATE THE WIRE ON THE VEHICLE SIDE V (+) (-) WHEN RUNNING (-) OUTPUT DATA MODE LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) VEHICLE MAIN IGNITION 7.5 AMPS USE DATA MODE OR HARDWIRE MODE DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE - BLACK V (+) - RED IGNITION (+) INPUT - PINK (NC) PINK/BLACK (NC) ORANGE (NC) GRAY/YELLOW ECM - GRAY/RED (NC) GREEN/YELLOW ECM - GREEN/RED (NC) BLUE/YELLOW (NC) BLUE/RED WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) CONNECT TO THE VEHICLE MAIN IGNITION. DO NOT USE THE OEM CIRCUITRY. THE MODIFICATION WILL PERMANENTLY REMAIN IN THE VEHICLE.

12 Page of 5 ADS-TB-FM-EN Doc. No.: ##3956## INSTALLATION MODE SELECTION Press and release programming button to select installation mode. LED flashes (X) once = DATA MODE LED flashes (X) twice = STANDARD HARDWIRE MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. WARNING: READ CAREFULLY IMPORTANT I This firmware solution offers two different module programming procedures. The first module programming procedure uses two OEM keys. The second module programming procedure uses only one OEM key and the KLON technology. PERFORM ONLY ONE OF THE TWO MODULE PROGRAMMING PROCEDURES

13 ADS-AL(TB)-FM PAGE - INSTALL GUIDE MODULE PROGRAMMING PROCEDURE - WITH TWO OEM KEYS Page 3 of 5 ADS-TB-FM-EN Doc. No.: ##3956## NOTE I To complete this procedure, both OEM keys are required. OR 6 7 ON Turn key to ON position. Wait, LED will turn solid RED then will turn OFF. II Keep both OEM remotes at least 0 feet away from the vehicule. Æ Use both valet keys for the module programming procedure. Æ 8 Remove key. Insert key into ignition. 9 Press and release programming button. ON Turn key to ON position. 0 Remote start vehicle. OR! If the LED begins to flash RED, verify the and connections between the module and the vehicle. Jump the igntion to volts. 3 If LED turns solid GREEN for seconds. Module Programming Procedure completed. If LED turns solid RED, proceed with following step within 5 seconds, after LED turns OFF.! 0 AMPS IGNITION V If the LED begins to flash RED, you are using a cloned key or used the same key twice. Remove key. Wait, LED will turn solid RED then will turn solid GREEN. 5 Insert key into ignition. Module Programming Procedure completed.

14 Page of 5 ADS-TB-FM-EN Doc. No.: ##3956## MODULE PROGRAMMING PROCEDURE - WITH ONE OEM KEY & KLON Insert key into ignition. 9 Remove module from vehicle. 3 ON Turn key to ON position. If LED turns solid GREEN for seconds. Module Programming Procedure completed. 0 Æ Æ Connect module to computer. If LED turns solid RED, proceed with following step within 5 seconds, after LED turns OFF. Press and hold programming button until LED truns solid RED, then release. Proceed with extended programming. Connect module to vehicle. 5 6! Wait, LED will flash GREEN. If the LED begins to flash RED/GREEN, the key has an 80-bit encryption that is not covered by KLON. OFF Turn key to OFF position. 3 5 Æ ON Insert key into ignition. Turn key to ON position. Wait, LED will turn solid GREEN for seconds. 7 8 Disconnect all connectors from module except the black -PIN standard or optional data connector. Disconnect the black -PIN standard or optional data connector. 6 7 OFF Turn key to OFF position. Module Programming Procedure completed.

15 Page 5 of 5 ADS-TB-FM-EN Doc. No.: ##3956## IDENTIFY VEHICLE YEAR Locate the Vehicle Identification Number (VIN), identify the 0th character then match it to its corresponding year. Æ 3 A 5 Y N 5 T A L 8 D 5 R 0 X Æ a 980 L 990 y 000 a 00 B 98 M B 0 C 98 n C 0 d 983 p d 03 e 98 r e 0 F 985 s F 05 G 986 T G 06 H 987 V H 07 J 988 W J 08 K 989 X K 09 Led status Flashing RED diagnostics during programming during remote start WITH IGnITIon off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE DISCONNECT all connectors from module EXCEPT the black -PIN standard or optional data connector. DISCONNECT black -PIN standard or optional data connector. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. 3 PRESS AND HOLD programming button while connecting either -PIN standard or optional data connector. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. When LED flashes red, RELEASE programming button.