Installation Tips for your Excalibur Remote Start system (for Ford vehicles) v3.02 updated 2/24/2012

Transcription

1 Installation Tips for your Excalibur Remote Start system (for Ford vehicles) v.0 updated /4/0 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to doit-yourself installers since 999. We ve put this tip sheet together to help you with your installation. The purpose of this sheet is to help you organize your installation - not to replace your installation manual. You will still need to refer to that. If you provided us with your vehicle model/year at the time of purchase, you will have a wiring chart for your particular vehicle. We re going to refer to that a lot. If you do not have the wiring chart, us at sales@mypushcart.com so we can send you a copy. Be sure to include the model/year of your vehicle, your name and your sales order number. Three very important things before you get started: Read the entire installation manual. There are several safety tips in there that you need to know before you start Avoid using a test light to probe wires. Test lights can set off air bags and damage ECU s, if you probe the wrong wire. Your vehicle wiring chart will identify the correct wires that you ll be tapping on to in your car. If you must probe, use a digital multi-meter. They re inexpensive and won t set off air bags or burn circuit boards. You will need to have TWO valid ignition keys to program your bypass. If you do not have two keys, you will need to get a coded key from your Ford dealer. ALL Ford bypasses require two keys for programming. Overview There are 4 basic steps to this remote start installation. We re going to address each of these:. Make your wiring connections for the remote start. Test the system. Program the bypass 4. Button it up! Need to know where all the components go? See Installer s Tip # on page 5 Step Wiring When you open up your remote start, you re going to see a whole bunch of wires. You re not going to use all of them. The remote starts are designed with wiring options for a variety of cars and no car is going to use all of them. We re going to break the wiring down into three parts your main power connections, what we ll call your secondary connections for your remote start, and connections for the bypass module (if you re using one). Here s where the vehicle wiring chart comes into play. The wiring chart will help you locate the wires in your car, that you re going to use. Don t be intimidated by all the different wires listed on the chart you re only going to be using a few of them. Your supplied wiring chart will come from Crimestopper. P a g e

2 Reading your wiring chart Each line of the wiring chart contains pieces of information that you will need (continued on next page): The Circuit or Wire/Function The color of the wire in the car The location of the wire in the car The illustrations below will show you where to find that information on your chart. Making your wiring connections The tables on the next pages show you where to connect the wires from your remote start into the car. Any wires on your remote start that are NOT listed in the table are NOT USED. Helpful Hint: In most cases, the wires on the remote start are way longer than needed. Trim off excess wire when you make your connections, but leave some slack - this will allow you a little flexibility when it comes time to stow the remote start module after the installation is completed. Remote Start Wire Red/White (6-pin harness) Red (6-pin harness) Pink/White (6-pin harness) Violet (6-pin harness) Orange (6-pin harness) Pink (6-pin harness) Connect to the wire for the circuit on the vehicle chart labeled: Constant Volts Constant Volts Ignition -Volts Starter Accessory Ignition # (not present on all vehicles) White/Black (-pin harness) Parking Lamp (IMPORTANT SEE NOTE ) White (-pin harness) Parking Lamp (IMPORTANT SEE NOTE ) Black (-pin harness) System Ground connect this to a solid metal ground in the car Brown/Red (-pin harness) Brake Light (also called Brake Switch ) P a g e

3 Black/White (-pin harness) Neutral Safety if you have an automatic transmission, ground this wire Grey (-pin harness) Hood Input (See NOTE ) Red/White (-pin harness) Trunk Release ( if equipped) Green ( -pin harness) Blue ( -pin harness ) Lock Unlock The connections below MAY be needed Green/Black (-pin harness) OEM Alarm Disarm connect this only if your car has a factory alarm system that goes off when you try to use the remote start Violet/White (-pin harness) Tach Signal (See NOTE ) NOTE The remote start has two parking light wires. You will only use one of them. On your vehicle wiring chart, look up the wire for the parking lights. Next to the wire color will be either a + or a -. If yours has the +, then use the white wire. If it has a -, use the white/black wire. NOTE The grey wire is used with a pin switch (included in your kit) to prohibit the remote start from activating while the hood is open. This is an important safety feature! NOTE Most vehicles will not require this connection. The remote start has a tach sensing circuit built in. The purpose of that circuit (or the tach wire if you need it) is to enable the remote start to detect when the engine has started so it will stop cranking the starter. When you test your system, if the starter keeps cranking after the engine has started, you ll need to connect the tach wire. Once the wire is connected, take two additional steps: ) Change Installer Programming Option # to the tach wire setting (see page in the installer s manual). ) Program the tach circuit as shown on page 0 of the installation manual. Your kit also includes a programming button. Plug the button into the remote start. For tips on where to install the button, see Installer s Tip # on Page 5 See Installer s Tip # on Page 5 for tips on how to make your wiring connections TRUNK RELEASE: If your vehicle is equipped with an electronic trunk/hatch release, you can control that function with your new remotes. The relay in your kit is only used when you have positive trigger (+) trunk release. Refer to your wiring sheet for this information. If you see a (-) next to trunk release on your wiring diagram, you will not need the relay. If you see a (+) next to trunk release in the wiring diagram for your vehicle you will need the relay. P a g e

4 Installing your bypass The OL-IB-FMTL bypass requires a total of 4 connections. The large black cable with the 4-pin green connector goes from the bypass to the green data port on the remote start. There is another, similar black cable in the kit with two black connectors you will not use that one. The Pink wire gets connected to the vehicle s primary ignition circuit. The pink wire from the remote start s 6- pin harness is already connected to that circuit, so you can just tap on to that. The Green/Red and Gray/Red wires connect to the RX and TX wires on your PATS connector. The connector is located on the steering column, near the key cylinder. The OL-IB-FMTL installation manual shows all the different types of PATS connectors, and where the RX and TX wires are found on each type. Suggestion: Don t use tap connectors on the RX and TX wires. The wires are small and sometimes a tap connector won t make good contact. We suggest you either wrap and tape or solder and tape these connections. See Installer s Tip # on page 6. Another suggestion: Don t program the bypass yet. We want to make sure the remote start is connected and working properly first. Step Test the System Once all your connections are made, you should test the system before programming the bypass and putting everything back together.. Put your key in the ignition, but leave it in the off position.. Press the start button on your remote to get the vehicle started. If the vehicle started, you re ready to program the bypass. If it did not start, go back and check your wiring again. Turn the car off by pressing the brake pedal. Step Program the Bypass Instructions for programming your bypass can be found at the end of this document. Make sure you have both of your keys and your remote fob handy, as the programming actions MUST be done within only a few seconds, as detailed in the instructions. Read through the instructions first before actually doing the programming! It will help enable you to complete the steps within the specified time. Two Important Things:. The first step of the programming process is the Installation Mode Selection Be sure to select DATA MODE. See Page 7 in the OL-IB-FMTL manual.. There are 6 steps within the Module Programming sequence. You MUST remove the nd key from the ignition after completing Step 4 and before doing Step 5. The manual isn t very clear on this, but it is an important part of the programming sequence. If you do not remove the key at that time, the module will not program. 4 P a g e

5 Step 4 Close it up! Once the bypass has been programmed, give the system one final test. Now gather up all your wiring and neatly bundle it together using zip ties or electrical tape. Find a secure place to put the remote start module and use zip ties to secure it. Make sure that the remote start wires are not near any moving parts on the steering wheel, pedals or emergency brake! Installer s Tips Tip # Where Everything Goes There are 4 parts to your system:. Remote start module the wiring for the module is done under the dash on the driver s side, so you ll want to install the module in that general area. Before you start wiring, look for a location where there s some open space that will fit the module. Pay attention to moving parts like the pedals, e-brake and steering column. Be sure to route your wiring away from those areas.. Bypass module can be stowed along with the remote start.. Programming button Requires a ¼ hole. Usually put in the driver s kick panel (that s the area forward of the door), the driver s side of the center console, or the underside of the dash. 4. Hood Pin Switch An important safety component! Requires a /8 hole. Find a location in the engine compartment to mount the switch where the closed hood will keep the plunger in the switch depressed. This is what prevents the car from starting when the hood is open. Tip # How to make your wiring connections It s very important that all your wiring connections be solid and secure. All remote start connections are tap on connections. This means that you do not need to cut the wires in the car. You simply need to tap on to the wires in the car to make your connections. Here are three different ways to do this: Method Solder and tape This is the method preferred by the best professional installers. It makes for the most reliable connections, but it is also the most difficult to do. Sometimes there isn t enough room in the wiring harness to safely solder a wire without damaging adjacent wires, but if you have the soldering skills, go for it. To make a connection, strip back a section of the insulation on the wire in the car. On heavy gauge wires, is about the right amount. On lighter gauge wires, ½ is fine. Strip of insulation off the end of the remote start wire. Tin the bare section of wire in the car. Wrap the remote start wire around the tinned section and then carefully solder it in place. Wrap the splice tightly with electrical tape. 5 P a g e

6 Method Wrap and tape This is the most popular method and is also very reliable. Strip back a section of the insulation on the wire in the car. On heavy gauge wires, is about the right amount. On lighter gauge wires, ½ is fine. Strip of insulation off the end of the remote start wire. Separate the strands of the wire like this: Pass the wire from the remote through the opening as shown below Wrap the remote start wire around both sides of the car wire, then back around itself as shown below Use electrical tape to wrap the connection and secure the wires together. A wire tie will help prevent the tape from unraveling in the future. Method # T-Taps T-taps are plastic clips that are squeezed onto the wires in the car. The wire from the remote start goes into the tap and the whole thing is crimped together. T-taps come in different sizes for different size wires. Use yellow t-taps for the larger wires in your main power harness. Red t-taps are good for the smaller wires. Tape and wire tie the connections as shown in the wrap and tape section above that will prevent the t-taps from ever opening up. We now have a tap kit available for purchase for those who prefer to use this method. The kit consists of two types of connectors - The taps and insulated male spade connectors that plug into them. The taps attach to the wires in the car and the spade connectors attach to the wires on the remote start. The spades then plug in to the taps. A crimping tool is required. If you re having problems programming the Bypass: Try these procedures to solve your problem! Go step by step, don t do another step unless the first doesn t work! ) Switch the RX and TX wires going to the bypass. ) Run the Red wire from the Bypass directly to a v+ constant circuit in the fuse box. Run the Black wire from the bypass directly to the closest ground (metal support). Test the Ground to make sure there is no resistance using your multi-meter. 6 P a g e

7 Copyright 0 Digitel LLC Did you find this document helpful? Please let us know so we can continue to improve our service to you. Suggestions are welcomed and encouraged! Please to sales@mypushcart.com 7 P a g e

8 Omega R&D Inc. INSTALL GUIDE OL-IB-FMTL FMTL AVAILABLE FOR : OL-IB-FMTL Rev. Date: February 0, 009 Doc. No.: ##008## PLEASE VISIT FOR COMPLETE PRODUCT DETAILS The brand names and logos found in this guide are property of their respective owners. Omega R&D Inc. 009 Pages: to 8 Pages: 9 to 0 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.

9 Page of 0 OL-IB-FMTL Doc. No.: ##008## VEHICLE COMPATIBILITY CHART. DETERMINE INSTALL TYPE Refer to chart below VEHICLE INSTALL TYPE MAKE MODEL Contour Crown Victoria E-Series Edge Escape Escape Hybrid Excursion Expedition Explorer Explorer Sport Trac F50 F-Series Super Duty FORD Five Hundred Flex Focus Freestar Freestyle Fusion GT Mustang Ranger Taurus Taurus X Thunderbird Windstar JAGUAR X-Type Aviator Blackwood Continental LS Mark LT LINCOLN MKS * MKX MKZ Navigator Town Car Zephyr 5 6 * B-Series MAZDA CX7 CX9 MX-5 RX-8 Tribute Cougar Grand Marquis Marauder Mariner Mariner Hybrid MERCURY Milan Montego Monterey Mountaineer Mystique Sable * without smartkey system ONLY. PROCEED WITH INSTALLATION See applicable wiring diagram NOTE: ENSURE ALL CONNECTIONS ARE COMPLETED AND PROPERLY SECURED PRIOR TO CONNECTING THE WIRE HARNESSES TO THE MODULE.

10 Page of 0 OL-IB-FMTL Doc. No.: ##008## WIRE CROSS REFERENCE CHART FORD VEHICLES MODEL YEAR PIN TX PIN RX CONN Contour Gray/Orange 4 White/Lt Green B Crown Victoria White/Lt Green Gray/Orange A White/Lt Green Gray/Orange C White/Lt Green 4 Gray/Orange E E-Series White/Lt Green Gray/Orange C Yellow/Orange Violet/Gray C Edge Violet/Gray 4 Yellow/Orange E Escape / Hybrid Brown/Orange 4 Red/Black B Excursion (early prod) Yellow/Orange 4 Violet/Gray E 00 (late prod) White/Lt Green Gray/Orange A 4 White/Lt Green Gray/Orange C Expedition White/Lt Green Gray/Orange A Explorer (early prod) White/Lt Green 4 Gray/Orange B Violet/Brown 4 Blue/Gray E 00 (late prod) (dr) 4 White/Lt Green Gray/Orange A 4 White/Lt Green Gray/Orange C White/Lt Green 4 Gray/Orange B Yellow/Orange 4 Violet/Gray E Explorer Sport Trac 00 (early prod) 4 White/Lt Green Gray/Orange A 00 (late prod) White/Lt Green Gray/Orange C Yellow/Orange 4 Violet/Gray E F White/Lt Green Gray/Orange A 00 4 White/Lt Green Gray/Orange C White/Lt Green 4 Gray/Orange B 009 Violet/Gray 4 Yellow/Orange E F-Series Super Duty Yellow/Orange 4 Violet/Gray E Five Hundred White/Lt Green 4 Gray/Orange E Flex 009 Yellow/Orange 4 Violet/Gray E Focus Gray/Orange 4 White/Green B Violet/Gray Yellow/Orange F Freestar White/Lt Green Gray/Orange C Freestyle White/Lt Green 4 Gray/Orange E Fusion (early prod) 007 (late prod) Violet/Gray 4 Yellow/Orange E Yellow/Orange 4 Violet/Gray E GT White/Orange 4 Brown/Orange B Mustang White/Lt Green Gray/Orange A White/Lt Green Gray/Orange C White/Lt Green 4 Gray/Orange E Ranger White/Lt Green Gray/Orange A White/Lt Green Gray/Orange C Violet/Brown Blue/Gray C Taurus Brown/Orange Red/Black A 00 4 Gray/Red Brown/Yellow A 00 4 Brown/Yellow Gray/Red C White/Lt Green Gray/Orange C Yellow/Orange 4 Violet/Gray E Taurus X Yellow/Orange 4 Violet/Gray E Thunderbird White/Red 4 Gray/red B Windstar White/Lt Green Gray/Orange A 00 4 White/Lt Green Gray/Orange C JAGUAR VEHICLES MODEL YEAR PIN TX PIN RX CONN X-Type White/Green 4 Orange B LINCOLN VEHICLES MODEL YEAR PIN TX PIN RX CONN Aviator White/Lt Green 4 Gray/Orange B Blackwood 00 4 White/Lt Green Gray/Orange A 00 4 White/Lt Green Gray/Orange C Continental 998 (early prod) White/Lt Green 4 Gray/Orange A 998 (late prod) White/Lt Green Gray/Orange A LS White/Red 4 Gray/red B Mark LT White/Lt Green 4 Gray/Orange B MKS (w/o smartkey) 009 Yellow/Orange 4 Violet/Gray E MKX Violet/Gray 4 Yellow/Orange E MKZ 007 (early prod) Violet/Gray 4 Yellow/Orange E 007 (late prod) Yellow/Orange 4 Violet/Gray E Navigator White/Lt Green Gray/Orange A White/Lt Green 4 Gray/Orange B Violet/Brown 4 Blue/Gray E Town Car White/Lt Green Gray/Orange A White/Lt Green Gray/Orange C White/Lt Green 4 Gray/Orange E Zephyr 006 Violet/Gray 4 Yellow/Orange E MAZDA VEHICLES MODEL YEAR PIN TX PIN RX CONN Gray/Orange White/Lt Green D Green Pink/Black D 6 (w/o smartkey) Green Orange/Lt Blue D 6 (with smartkey) Yellow/Green Gray D 6 (w/o smartkey) Gray/Orange White/Lt Green F B-Series White/Lt Green Gray/Orange A White/Lt Green Gray/Orange C Violet/Brown Blue/Gray C CX Gray/Orange White/Lt Green D CX Blue/Yellow Blue/Orange D MX-5 (w/o smartkey) Yellow/Black Lt Blue/Orange D MX-5 (with smartkey) Gray/Lt Blue Violet D RX Lt Blue/Orange Yellow/Black D Tribute Brown/Orange 4 Red/Black B Yellow/Orange 4 Violet/Gray E MERCURY VEHICLES MODEL YEAR PIN TX PIN RX CONN Cougar Gray/Orange 4 White/Green B Grand Marquis White/Lt Green Gray/Orange A White/Lt Green Gray/Orange C White/Lt Green 4 Gray/Orange E Marauder White/Lt Green Gray/Orange C Mariner / Hybrid Brown/Orange 4 Red/Black B Milan (early prod) Yellow/Orange 4 Violet/Gray E 007 (late prod) Violet/Gray 4 Yellow/Orange E Yellow/Orange 4 Violet/Gray E Montego White/Lt Green 4 Gray/Orange E Monterey White/Lt Green Gray/Orange C Mountaineer White/Lt Green Gray/Orange A White/Lt Green 4 Gray/Orange B Yellow/Orange 4 Violet/Gray E Mystique Gray/Orange 4 White/Lt Green B Sable Brown/Orange Red/Black A 00 4 Gray/Red Brown/Yellow A 00 4 Brown/Yellow Gray/Red C White/Lt Green Gray/Orange C Yellow/Orange 4 Violet/Gray E

11 Page 4 of 0 OL-IB-FMTL Doc. No.: ##008## TYPE WIRING DIAGRAM IMMOBILIZER CONNECTOR TYPE: Connectors B, D, E, F and G located at immobilizer near key barrel Connectors A and C are found TYPE 8 inches INSTALL lower on PATS harness. A 4 B 4 C 4 D 4 PIN WIRE DESCRIPTION GROUND PATS V. POWER RX 4 TX PIN WIRE DESCRIPTION PATS V. POWER GROUND TX 4 RX PIN WIRE DESCRIPTION GROUND PATS V. POWER RX 4 TX PIN WIRE DESCRIPTION RX TX GROUND 4 PATS V. POWER E F PIN WIRE DESCRIPTION PATS V. POWER GROUND TX 4 RX PIN WIRE DESCRIPTION 8 PATS V. POWER 6 GROUND RX 4 TX LEGEND Wiring connections not required when using the DBI Port. WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED - ECM-RX GREEN/YELLOW (NC) GRAY/RED - ECM-TX GRAY/YELLOW (NC) ORANGE (NC) PINK/BLACK (NC) PINK - IGNITION INPUT DO NOT CONNECT THE IGNITION INPUT AT THE PATS MODULE, CONNECT TO THE MAIN VEHICULE IGNITION INSTEAD CONNECT EITHER DBI OR STANDARD WIRING RED - V BLACK - GROUND NO WIRE (NC) BLUE/WHITE - GROUND-OUT WHEN RUNNING DBI PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD DBI PORT REMOTE STARTERR

12 Page 5 of 0 OL-IB-FMTL Doc. No.: ##008## TYPE WIRING DIAGRAM IMMOBILIZER CONNECTOR TYPE: Connectors B, D, E, F and G located at immobilizer near key barrel Connectors A and C are found 8 inches lower on PATS harness. A 4 B 4 C 4 D 4 PIN WIRE DESCRIPTION GROUND PATS V. POWER RX 4 TX PIN WIRE DESCRIPTION PATS V. POWER GROUND TX 4 RX PIN WIRE DESCRIPTION GROUND PATS V. POWER RX 4 TX PIN WIRE DESCRIPTION RX TX GROUND 4 PATS V. POWER E F PIN WIRE DESCRIPTION PATS V. POWER GROUND TX 4 RX PIN WIRE DESCRIPTION 8 PATS V. POWER 6 GROUND RX 4 TX LEGEND Wiring connections not required when using the DBI Port. WHITE/BLACK - RX - PATS SIDE WHITE/RED - RX - ECM SIDE WHITE (NC) BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED - ECM-RX GREEN/YELLOW (NC) GRAY/RED - ECM-TX GRAY/YELLOW (NC) ORANGE (NC) PINK/BLACK (NC) PINK - IGNITION INPUT DO NOT CONNECT THE IGNITION INPUT AT THE PATS MODULE, CONNECT TO THE MAIN VEHICULE IGNITION INSTEAD CONNECT EITHER DBI OR STANDARD WIRING RED - V BLACK - GROUND NO WIRE (NC) BLUE/WHITE - GROUND-OUT WHEN RUNNING DBI PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD DBI PORT REMOTE STARTERR

13 Page 6 of 0 OL-IB-FMTL Doc. No.: ##008## TYPE WIRING DIAGRAM IMMOBILIZER CONNECTOR TYPE: Connector B is located at immobilizer near key barrel B 4 PIN WIRE DESCRIPTION PATS V. POWER GROUND TX 4 RX PATS POWER WIRING CHART MAKE MODEL YEAR PIN PATS POWER CONN Ford Thunderbird Orange/Blue B Jaguar X-Type Green B Lincoln LS Orange/Blue B For RX and TX wires listing, please refer to the Wiring chart found at the beginning of this guide LEGEND Wiring connections not required when using the DBI Port. PATS POWER CONNECT TO THE VEHICULE MAIN IGNITION INSTEAD OF USING THE OEM CIRCUITRY. THE MODIFICATION WILL PERMANENTLY REMAIN IN THE VEHICLE. 7.5 AMPS SECURE AND INSULATE THE WIRE ON THE VEHICLE SIDE WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED - ECM-RX GREEN/YELLOW (NC) GRAY/RED - ECM-TX GRAY/YELLOW (NC) ORANGE (NC) PINK/BLACK (NC) PINK - IGNITION INPUT CONNECT EITHER DBI OR STANDARD WIRING RED - V BLACK - GROUND NO WIRE (NC) BLUE/WHITE - GROUND-OUT WHEN RUNNING DBI PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD DBI PORT REMOTE STARTERR

14 V INSTALL GUIDE Page 7 of 0 OL-IB-FMTL Doc. No.: ##008## INSTALLATION MODE SELECTION Press and release the programming button to select To register selection, hold the programming button down until the LED installation mode. displays a solid GREEN light. Press to toggle between modes Press & Hold DATA MODE LED flashes once X OR STANDARD MODE LED flashes twice X REMOTE STARTER WITH DATA PORT REMOTE STARTER WITHOUT DATA PORT NOTE To change the current installation mode once registered, apply a Factory Reset and restart this procedure. PROGRAMMING STEP MODULE PROGRAMMING IMPORTANT: BOTH KEYS ARE REQUIRED TO COMPLETE THE PROGRAMMING PROCEDURE ON Insert the FIRST vehicle key into the ignition and turn the ignition to the ON position. (Note: if the LED begins to flash RED, please verify the RX and TX connections between the module and the vehicle). 5 Press and release the programming button and, WITHIN 5 SECONDS, remote start the vehicle or jump the main ignition to a main V wire. LED ON SEC If the LED illuminates GREEN for SECONDS. Programming is completed and the module is ready for remote start. IF THE LED ILLUMINATES RED, PROCEED WITH PROGRAMMING STEP WITHIN 5 SECONDS AFTER THE LED TURNED OFF. PRESS + RELEASE + Start the vehicle using the remote controlled starter PROGRAMMING STEP REQUIRED FOR MOST 000+ VEHICLES OR ON Insert the SECOND key and turn the ignition to the ON position. (Module LED will illuminate RED.) LED RED Jump the ignition to Volts. 0 AMPS IGNITION 4 LED OFF The LED will turn "OFF" to confirm the vehicle has validated the key. (Note: if the LED begins to flash RED, you are using a cloned key or used the same key twice). 6 RED THEN GREEN is turned off. IF SUCCESSFUL The LED will turn RED to indicate the learning procedure has begun. The LED will then turn GREEN to confirm programming has succeeded. The green LED will remain illuminated until ignition FOR RFID SMART KEYS PLEASE REFER TO THE THE NEXT PAGE

15 V INSTALL GUIDE Page 8 of 0 OL-IB-FMTL Doc. No.: ##008## SMART KEY MODULE PROGRAMMING IMPORTANT: BOTH KEYS ARE REQUIRED FOR PROGRAMMING Remove the valet keys from each SMART KEY card. Put the cards far from the vehicle. FAR FROM THE VEHICLE Use the valet keys to continue programming. REMOVE PROGRAMMING ON Insert the first key and turn the ignition to the ON position. (Module LED will illuminate RED.) LED RED 4 Press and release the programming button and, WITHIN 5 SECONDS, remote start the vehicle or jump the main ignition to a main V wire. PRESS + RELEASE LED OFF The LED will turn "OFF" to confirm the vehicle has validated the key. (Note: if the LED begins to flash RED, please verify the RX and TX connections between the module and the vehicle). + Start the vehicle using the remote controlled starter OR Jump the ignition to Volts. 0 AMPS REPEAT STEPS & WITH SECOND KEY IGNITION 5 RED THEN GREEN IF SUCCESSFUL The LED will turn RED to indicate the learning procedure has begun. The LED will then turn GREEN to confirm programming has succeeded. The green LED will remain illuminated until ignition is turned off.

16 Page 9 of 0 OL-IB-FMTL Doc. No.: ##008## VEHICLE COMPATIBILITY CHART. DETERMINE INSTALL TYPE Refer to chart below LEGEND / - Type may vary by vehicule equipment level. / - Type may be standard key or push to start. NC - Not covered WARNING Please advise that the install type numbers have changed since the last revision of this install guide. NOTES Type install provides simulated tach output for hybrid vehicles. A hybrid vehicle might be running without its engine being running. To determine whether a hybrid vehicle is running or not, look at the instrument cluster, radio and heating system. Push to Start vehicles have a maximum take over time of 45 seconds: for security reasons, during the remote starter runtime, the driver must press the unlock button of the remote starter fob to trigger a 45 seconds time window which will permit him/her to step into the vehicle and press the brake pedal to complete take over. INSTALL TYPE MAKE MODEL Runner Avalon / / / / / Camry / / / / / Camry Hybrid Corolla / FJ Cruiser Hiace Highlander / / Highlander Hybrid 5 5 Hilux Land Cruiser NC TOYOTA Matrix MR Spyder Prius RAV4 / Sequoia Sienna Solara / / Tacoma Tundra Venza (standard key only) Yaris ES 00 ES 0 ES 50 NC GS 00 GS 50 NC GS 400 GS 40 GS 450 Hybrid NC GS 460 NC GX 470 IS 50 NC IS 00 IS 50 NC LEXUS IS-F NC LS 400 LS 40 / / / LS 460 NC LS 600 Hybrid NC LX 470 LX 570 NC NC RX 00 RX 0 RX 50 RX 400 Hybrid SC 00 SC 400 SC 40 PONTIAC Vibe SCION tc. PROCEED WITH INSTALLATION See applicable wiring diagram

17 Page 0 of 0 OL-IB-FMTL Doc. No.: ##008## TYPE WIRING DIAGRAM AND CROSS-REFERENCE CHART CONNECTIONS MAY VARY ACCORDING TO VEHICLE. REFER TO CHART FOR CONNECTION DETAILS TO IMMOBILIZER WHITE/BLACK- RXCK KEY SIDE WHITE/RED - RXCK CAR SIDE WHITE (NC) LEGEND BLUE/RED - TXCT BLUE/YELLOW (NC) GREEN/RED - DATA GREEN/YELLOW (NC) GRAY/RED - RXCK CAR SIDE GRAY/YELLOW (NC) ORANGE - AMP PINK/BLACK - CODE KEY SIDE PINK - CODE ECM SIDE RED - V BLACK - GROUND NO WIRE (NC) BLUE/WHITE - GROUND-OUT WHEN RUNNING CONNECT EITHER DBI OR STANDARD WIRING DBI PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD DBI PORT DIODE REMOTE STARTERR *Use isolated Ground-Out When Running from remote starter to power key sense REQUIRED: x DIODE Wiring connections not required when using the DBI Port. MODEL YEAR PIN AMP PIN CODE PIN RXCK PIN TXCT PIN GROUND (-) KEY SENSE CONN. 4Runner White/Blue Gray/Red Red/Black 4 Pink/Black 5 Brown Yellow/Red A Avalon Light Green Black/Red Yellow 4 Green 5 White/Black Red/Yellow A Avalon Black/White Pink/Green Blue/Orange 4 Blue/Yellow 5 White/Black Red/White A Camry Black/Yellow Green/White Red/Blue 4 Blue/Yellow 5 White/Black Blue/Black A Camry (4cyl) Black/Red 4 Green/White Red/Blue 5 Blue/Yellow 7 White/Black Blue B Camry (6cyl) 00-0 Black/Red 4 Green/White Red/Blue 5 Blue/Yellow 7 White/Black Blue B ES Black/Yellow Green/White Red/Blue 4 Blue/Yellow 5 White/Black Blue/Black A ES Black/Red 4 Green/White Red/Blue 5 Blue/Yellow 7 White/Black Blue B GS Black/Red Green/Black Black/White 4 Blue/Red 5 White/Black Yellow E GS Black/Red Green/Black Black/White 4 Blue/Red 5 White/Black Yellow A GS Black/Red Green/Black Black/White 4 Blue/Red 5 White/Black Yellow E GS Black/Red Green/Black Black/White 4 Blue/Red 5 White/Black Yellow A Highlander 00-0 White 4 Gray/Blue Pink 5 Gray 7 White/Black Blue B IS Black/Red Green Purple 4 Pink 5 White/Black Black/Yellow A IS Black/Red Green/Black Purple 4 Pink/Black 5 White/Black Black/Yellow A Land Cruiser Black/Yellow Blue/Black Purple/Green 4 Red/Yellow 5 White/Black Red/Black E LS White Red/White Red/Black 4 Red 5 White/Black Yellow A LS Orange 4 Red/White White/Red 5 Light-Blue/Black 7 Violet Lt Green/Black B LS 40 (smartkey) Red 4 Orange Light Blue 5 Yellow/Black 7 Violet Lt Green/Black B LX Black/Yellow Blue/Black Purple/Green 4 Red/Yellow 5 White/Black Red/White E MR Spyder Black Blue/Yellow 4 Yellow Blue/Black White/Black Yellow/Red C RAV Black/Red Yellow/Green 4 Yellow Yellow/Black White/Black Blue/Red C RX Blue/White Purple Black 4 Gray 5 White/Black Blue A RX Blue/White Purple Pink 4 Gray 5 White/Black Blue A RX Black/Red Purple Pink 4 Gray 5 White/Black Blue A SC Black/Red Black/Orange Blue 4 Green/Orange 5 White/Green Yellow A SC Black/Red Black/Orange Blue 4 Green/Orange 5 White/Green Yellow A SC Yellow Violet/White Red 4 Green 5 Violet Light Green/Black A Sequoia 00-0 Black/Red 4 Red/Yellow 5 Light Green 6 Yellow/Green Orange Yellow/Green D Sequoia Gray/Black 4 Red/Yellow 5 Light Green 6 Yellow/Green Gray/Light Blue Yellow/Green D Sienna Black/Red Brown/White Brown/Red 4 Brown/Yellow 5 White/Black Blue/Black A Solara Red Green/White Red/Blue 4 Blue/Yellow 5 White/Black Blue/Black A Tundra S. Cab 006 Red Green 4 Blue/Red 5 Gray Pink Pink/Black D Tundra D. Cab 006 White 4 Green 5 Red 6 Black Gray Yellow/Green D CONNECTOR TYPE: Connector is located at immobilizer near key barrel or 8 inches lower on the immobilizer harness. A B D E C

18 Page of 0 OL-IB-FMTL Doc. No.: ##008## TYPE WIRING DIAGRAM KEYSENSE(-) WHITE/BLACK - KEYSNENSE (-) WHITE/RED NC) WHITE - GROUND LEGEND Wiring connections not required when using the DBI Port. BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED - CODE GREEN/YELLOW (NC) GRAY/RED - TXCT GRAY/YELLOW (NC) ORANGE (NC) PINK/BLACK (NC) PINK(NC) RED - V BLACK - GROUND NO WIRE (NC) BLUE/WHITE - GROUND-OUT WHEN RUNNING CONNECT EITHER DBI OR STANDARD WIRING DBI PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD DBI PORT REMOTE STARTERR CODE TXCT PLEASE REFER TO THE WIRING CROSS-REFERENCE CHART FOUND ON NEXT PAGE

19 Page of 0 OL-IB-FMTL Doc. No.: ##008## TYPE WIRE CROSS REFERENCE CHART MODEL YEARS PIN CODE PIN TXCT KEY SENSE 4Runner Pink/Green 5 Light Green/Red Green/Yellow Avalon Light/Green 5 Brown Black Camry Green/White 5 Blue/Yellow Blue Camry Brown 5 Red Blue Corolla Blue 5 Green Blue/Black Corolla (Japan) Light Blue 5 Beige Light Blue Corolla (Canada) Pink 5 Green Light Blue FJ Cruiser Pink/Green 5 Light Green/Red Green/Yellow Hiace Blue 5 Yellow Yellow/Black Highlander Gray 5 White Green Highlander Red 5 Light Blue Light Blue Hilux Light Blue/Yellow 5 Light Blue/Black Green/Yellow Land Cruiser Blue/Black 5 Violet/Green Red/Black Matrix Blue 5 Green Blue/Black Matrix Light Blue 5 Beige Blue RAV Blue/Red 5 Pink Blue/Red RAV Pink 5 Green Blue Sequoia Light Green 5 Blue Gray Sienna Yellow 5 Yellow/Red Blue/Black Solara (Convertible) Green/White 5 Blue/Yellow Blue Solara (Coupe) Yellow 5 Yellow/Red Blue Tacoma Pink/Green 5 Light Green/Red Green/Black Tundra Light Green 5 Blue Gray Venza Light Green 5 Brown Brown Yaris Green 5 Violet Yellow ES Green/White 5 Blue/Yellow Blue GX Yellow 5 Yellow/Black Green/Yellow LS Red/White 5 Blue/Black Light Green/Black LX Blue/Black 5 Violet/Green Red/Black RX Light Green 5 Brown Black RX Light Green 5 Brown Black Vibe Blue 5 Green Blue/Black Vibe Light Blue 5 Beige Blue tc Yellow 5 Red Black

20 Page of 0 OL-IB-FMTL Doc. No.: ##008## TYPE WIRING DIAGRAM REQUIRED: x K RESISTOR x RELAY 4x DIODES WITH DOORLOCKS FEATURE or x DIODES WITHOUT DOORLOCKS ENGINE START STOP BLUE/RED - GROUND BLUE/YELLOW - PUSH (-) GREEN/RED - CODE GREEN/YELLOW (NC) GRAY/RED - TXCT GRAY/YELLOW (NC) ORANGE - TACH PINK/BLACK (NC) PINK - SYNCHRO TXCT CODE PUSH(-) (NC)WHITE/RED WHITE/BLACK WHITE REMOTE STARTER WARNING DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLING THE REQUIRED VEHICLE POWERS AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. WARNING IGNITION IS USED ONLY AS AN INPUT TO THE REMOTE STARTER, NOT AN OUTPUT TO THE VEHICLE. DIODE CATHODE NEEDS TO BE FACING THE REMOTE STARTER UNLOCK (-) ACCESSORY (+) TACH (AC) BRAKE (+) IGNITION (+) RED - V BLACK - GROUND NO WIRE (NC) BLUE/WHITE - GROUND-OUT WHEN RUNNING CONNECT EITHER DBI OR STANDARD WIRING DBI PORT DBI PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD LOCK (-) K * * LEGEND Wiring connections not required when using the DBI Port. *NOTE: FACTORY KEYFOB WILL NOT FUNCTION WHEN REMOTE STARTER IS ENGAGED. FOR AFTERMARKET KEYFOB FUNCTIONALITY, HARDWIRE REMOTE STARTER DOORLOCKS 87 B 85 87A 86 BRAKE LAMP 0 V BRAKE SW A VEHICLE IGNITION CAN BE FOUND AT BRAKE PEDAL 4 PLEASE REFER TO THE WIRING CROSS-REFERENCE CHART FOUND ON NEXT PAGE

21 Page 4 of 0 OL-IB-FMTL Doc. No.: ##008## TYPE WIRE CROSS REFERENCE CHART MODEL YEARS PIN CODE PIN TXCT PIN PUSH PIN IGNITION PIN V (BRAKE) PIN BRAKE Avalon (smart key) White 9 Gray 7 Blue A Brown A Black A White Camry Hybrid White 9 Gray 7 Blue A Black A Black A White Camry (smart key) White 9 Gray 7 Blue A Black A Black A Blue Corolla (smart key) Green 9 Light Blue 7 White A Black A White A Blue Highlander (smart key) Gray 9 Orange 7 Pink A White A Violet A Blue Highlander Hybrid Gray 9 Orange 7 Pink A White A Violet A Blue Land Cruiser Green 9 Light Blue 7 Black B Black B Blue/Black B Red RAV4 (smart key) White 9 Blue 7 White B4 Black B White B Blue ES White 9 Gray 7 Blue A Black A Black A Blue GS Yellow 9 Blue 7 Pink B Black/White A Blue/White B Red/Black GS Yellow 9 Blue 7 Pink B Black/White B Blue/White B Red/Black GS Yellow 9 Blue 7 Pink B Black/White B Blue/White B Red/Black GS 450 Hybrid Yellow 9 Blue 7 Pink B Black/White B Blue/White B Red/Black GS Yellow 9 Blue 7 Pink B Black/White B Blue/White B Red/Black IS Light Blue 9 Blue 7 Black B4 Light Green B Blue/White B Red/Black IS Light Blue 9 Blue 7 Black B4 Light Green B Blue/White B Red/Black IS-F Light Blue 9 Blue 7 Black B4 Light Green B Blue/White B Red/Black LS White 9 Orange 7 White B Red B Green B Blue LS 600 Hybrid White 9 Orange 7 White B4 Light Green B Green B Red/Black

22 Page 5 of 0 OL-IB-FMTL Doc. No.: ##008## TYPE 4 WIRING DIAGRAM AND CROSS-REFERENCE CHART ENGINE START STOP YELLOW PUSH(-) REQUIRED: 5x DIODES x K RESISTOR x RELAYS LIGHT GREEN BLUE KEYPORT BLUE/RED - GROUND BLUE/YELLOW - PUSH (-) GREEN/RED - CODE GREEN/YELLOW (NC) GRAY/RED - TXCT GRAY/YELLOW (NC) ORANGE - TACH PINK/BLACK (NC) PINK - SYNCHRO TXCT CODE 5 4 BLUE WHITE - BRAKE RELAY CONTROL (-) (NC)WHITE/RED WHITE/BLACK REMOTE STARTER WARNING DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLING THE REQUIRED VEHICLE POWERS AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. WARNING IGNITION IS USED ONLY AS AN INPUT TO THE REMOTE STARTER, NOT AN OUTPUT TO THE VEHICLE. DIODE CATHODE NEEDS TO BE FACING THE REMOTE STARTER UNLOCK (-) ACCESSORY (+) TACH (AC) IGNITION (+) RED - V BLACK - GROUND NO WIRE (NC) BLUE/WHITE - GROUND-OUT WHEN RUNNING CONNECT EITHER DBI OR STANDARD WIRING DBI PORT DBI PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD GROUND WHEN RUNNING (-) LOCK (-) K * * 85 0 *NOTE: FACTORY KEYFOB WILL NOT FUNCTION WHEN REMOTE STARTER IS ENGAGED. FOR AFTERMARKET KEYFOB FUNCTIONALITY, HARDWIRE REMOTE STARTER DOORLOCKS 87 87A 86 PINK V (+) KEYSENSE (-) KEY LOCK SOLENOID (+) BRAKE (+) 87 LEGEND Wiring connections not required when using the DBI Port A 86 V 0 BRAKE LAMP BRAKE SW VEHICLE IGNITION CAN BE FOUND AT BRAKE PEDAL SWITCH 4 A MODEL YEARS PIN CODE PIN TXCT PIN PUSH PIN IGNITION PIN V (BRAKE) PIN BRAKE Prius Blue 5 Light Green 7 Yellow A Orange A Black A Blue

23 Page 6 of 0 OL-IB-FMTL Doc. No.: ##008## TYPE 5 WIRING DIAGRAM AND CROSS-REFERENCE CHART IMMOBILIZER CONNECTOR KEYSENSE (-) IGNITION CONNECTOR C CODE ACCESSORY (+) WHITE/BLACK - KEYSENSE (-) WHITE/RED NC) WHITE - GROUND BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED - CODE GREEN/YELLOW (NC) GRAY/RED - TXCT GRAY/YELLOW (NC) ORANGE - TACH PINK/BLACK (NC) PINK - ACCESSORY TXCT CONNECT TO ACCESSORY (+) AT THE IGNITION SWITCH. ACCESSORY WIRE HAS TO DROP TO 0 VOLT DURING ENGINE CRANK CYCLE TACH (AC) ACCESSORY (+) RED - V BLACK - GROUND NO WIRE (NC) BLUE/WHITE - GROUND-OUT WHEN RUNNING REMOTE STARTER LEGEND Wiring connections not required when using the DBI Port. CONNECT EITHER DBI OR STANDARD WIRING DBI PORT DBI PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD MODEL YEARS PIN CODE PIN TXCT KEYSENSE PIN ACCESSORY Highlander Hybrid Grey 5 Light Blue Green C4 Green RX 400 Hybrid Light Green 5 Brown Black C4 Green

24 Page 7 of 0 OL-IB-FMTL Doc. No.: ##008## INSTALLATION MODE SELECTION Press and release the programming button to select To register selection, hold the programming button down until the LED installation mode. displays a solid GREEN light. Press to toggle between modes Press & Hold DATA MODE LED flashes once X OR STANDARD MODE LED flashes twice X REMOTE STARTER WITH DATA PORT REMOTE STARTER WITHOUT DATA PORT NOTE To change the current installation mode once registered, apply a Factory Reset and restart this procedure. Open the KEYFOB and remove the CIRCUIT BOARD. MODULE PROGRAMMING PUSH TO START VEHICLE PROGRAMMING 4 Place the circuit board against the engine start/stop button. Press the start/stop button. Make sure to obtain a succesful ignition cycle. As soon the ignition will be powered up, the module will learn. Remove the BATTERY from the circuit board. ENGINE START STOP PUSH 5 The LED will blink GREEN and RED during the learning process, Keep the vehicle ignition ON. REMOVE LED BLINKING COLORS Confirm there isn t another RFID fob in the vehicle. Try to start the vehicle by pressing on the brake pedal and the start/stop button. If the vehicle refuses to start you are ready to proceed with step 4. If the vehicle starts, 6 Wait for the LED to illuminate GREEN for SECONDS. Programming is complete. find and remove the remaining RFID fob from the vehicle before proceeding with step 4. LED ON SEC

25 Page 8 of 0 OL-IB-FMTL Doc. No.: ##008## INSTALLATION MODE SELECTION Press and release the programming button to select To register selection, hold the programming button down until the LED installation mode. displays a solid GREEN light. Press to toggle between modes Press & Hold DATA MODE LED flashes once X OR STANDARD MODE LED flashes twice X REMOTE STARTER WITH DATA PORT REMOTE STARTER WITHOUT DATA PORT NOTE To change the current installation mode once registered, apply a Factory Reset and restart this procedure. VEHICLES WITH KEY PROGRAMMING MODULE PROGRAMMING VEHICLES WITH KEYPORT PROGRAMMING Insert the vehicle key into the ignition. Insert the key into the keyport. Once the key will be inserted in the ignition the learning process will begin, which will be indicated by the LED flashing GREEN and RED as long as the module is learning. Once the key will be inserted in the keyport the learning process will begin, which will be indicated by the LED flashing GREEN and RED as long as the module is learning. LED BLINKING COLORS LED BLINKING COLORS Wait for the LED to illuminate solid GREEN for SECONDS. Programming is complete. Wait for the LED to illuminate solid GREEN for SECONDS. Programming is complete. LED ON SEC LED ON SEC

26 Page 9 of 0 OL-IB-FMTL Doc. No.: ##008## MODULE DIAGNOSTICS MODULE DIAGNOSTICS DURING PROGRAMMING SOLID RED MODULE WAITING FOR MORE VEHICLE INFORMATIONS LED GREEN SOLID THEN OFF CORRECTLY PROGRAMMED FLASHING RED MISSING/WRONG CONNECTIONS OR FIRMWARE LED OFF NO ACTIVITY OR ALREADY PROGRAMMED MODULE DIAGNOSTICS DURING REMOTE START FLASHING GREEN CORRECTLY PROGRAMMED AND OPERATIONAL SOLID RED INCORRECTLY PROGRAMMED FLASHING RED INCORRECTLY PROGRAMMED LED OFF INVALID GROUND WHEN RUNNING STATUS FROM R.S. MODULE DIAGNOSTICS WITH IGNITION OFF LED OFF AT REST AND READY FOR A R.S. SEQUENCE SOLID RED NOT PROGRAMMED AND STILL WAITING FOR VEHICLE INFO FLASHING RED INCORRECTLY PROGRAMMED OR CONNECTED FLASHING GREEN FALSE GROUND WHEN RUNNING STATUS FROM R.S. FACTORY RESET PROCEDURE Unplug all connectors Press and hold the programming The LED will begin to flash red. 4 from the module. button while inserting either the Immediately release the programming 4-PIN standard or 4-PIN optional data connector. FACTORY RESET button. The LED will turn on solid red for seconds to confirm module reset. Once the reset is confirmed, reconnect all the remaining connectors and repeat the programming procedure UNPLUG CONNECTORS HOLD INSERT 4 PIN CONNECTOR WHEN THE LED FLASHES RED, RELEASE THE BUTTON SOLID RED LED CONFIRMS RESET

27 Doc. No.: ##008## PUSH TO START VEHICLE USER NOTE ATTENTION! PRIOR TO ENTERING THE VEHICLE.... Press the UNLOCK button on your after-market remote or OEM fob.. You will then have a 45 second delay during which you have to step in the vehicle and press on the brake pedal to complete take over without engine shutdown.. Please note that if an RFID remote is present in the vehicle, it will prevent proper remote start sequence.