PRO Grain Extractor. Manufactured by Arc Alloy Welding (1984) Colonsay, Sask. Owner s Guide to Use 1610 Model

Transcription

1 PRO Grain Extractor Manufactured by Arc Alloy Welding (1984) Colonsay, Sask. Owner s Guide to Use 1610 Model

2 NOTE: Safety Warnings Before operating extractor, familiarize yourself with all safety decals and their locations on the PRO Extractor. IMPORTANT SAFETY WARNING Roller handle is NOT detented DO NOT use bungee cord to hold handle Roller handle Refer to our website for extractor video

3 Set up Instructions Set up Extractor 1. Attach the tractor draw bar to the extractor hitch with 1 1/8 draw pin. Hook up safety chains. 2. Attach the PTO and make sure it is locked. 3. Connect hydraulic hoses. Lift extractor high enough to remove transport stop (Image 1) and replace with 3 stop (Image 2). 4. Lift the support leg (image 3) up and pin in temporary position (image 3A). Release the transport pin (image 4) that holds bag roller and swing roller into working position. 5. Replace the support leg and pin the bag roller in place (image 5). 6. Pivot the bag knife (image 6) from the storage position to the operating position shown in (image 7). Pin in place. 7. Raise the top of the auger into working position. Image 1 Image 2 Image 3 Image 3A

4 . Image 4 Roller transport pin Roller pin Image 5 Image 6 Image 7

5 Installing the bag onto PRO Grain Extractor 1. To begin make a horizontal cut just before the grain in the loose part of the bag. Then cut towards the tractor from the horizontal cut splitting the bag down the center. Do not cut the part of the bag that is under tension. See dwg 1 2. Back extractor up to the end of the bag with the bag between the wheels and cross augers are inside the bag. The main auger should go into the cut in the top of the bag. 3. Make sure the roller is stationary and hooks are toward the bag. Starting from the center of the bag, hook the bag onto the roller. Ensure all personnel are well clear of the roller. Rotate the roller one or more turns until bag is completely wrapped around the roller. 4. Lower the extractor on to 3 stop (image 2). The cross auger should be approximately 3 off the ground. dwg 1 Image 2

6 Extracting the grain 1 Roll up the bag until cross augers are into the grain. The cutting knife should line up with the cut in the top of the bag. 2 Ensure the unloading auger is lifted into position and the grain truck/cart is in position ready to load. After first making sure the tractor is in neutral, slowly engage the PTO. Once augers are engaged start the bag roller, adjust roller speed so cross augers stay full of grain. 3 PTO speed can be increased to 540 once grain is flowing. Removing the bag from the Extractor 1 To remove the bag from the roller, raise the extractor into transport position. Rotate the handles on the roller drive plate until they disengage. See image 12 2 Slowly drive the tractor and extractor forward until the bag is fully unrolled. Image 12 Notes: Raise and lower upper auger at least three times to pump hydraulic cylinder.

7 & & Parts list see following pages for part numbers and descriptions

8 Extractor Parts list # 1 Main Drive Part # Description SA bearing locking collar 1 1/2" F bolt flange 8820L PWL sprocket #80 x 20 tooth 80BB12H3/4NTL Idler sprocket # 80 H80 1 rl #80 heavy chain H80cl & H80os #H80 connector & off set link R Large PTO # 2 Main drive line SA bearing locking collar 1 1/2" F bolt flange /2" NTL Sprocket 50 x 18 tooth /8" NTL Sprocket 50 x 18 tooth rl chain Double roller chain #50 # 3 Lower Auger Drive ST L 90* gear box ST T "T" gear box /2" Sprocket 50 x 18 tooth /8" sprocket 50 x 17 tooth rl chain Double roller chain #50 50cl & 50os 50 connector & off set link ZEL /2" x 25 1/4" shaft ZEL /2" x 22 5/8" shaft # 4 Cross Auger Drive 3500 Series or 8 series PTO /8" -6 spline pump adapter # 5 Lower auger flighting drive Part # Description H80Q23 #80 Q 23 tooth sprocket Q1 2 2" dia taper lock type hub H80P14 #80P14 tooth sprocket P 1 1/2 Taper lock type hub 2" UHMW rod 2" nylon chain tightner H80 Chain #80 chain 40" long UCHA D1LLJ Bearing special - NTN triple seal F210D Flange 210D ductile SA Bearing lock collar F208 F208 flange 4 bolt

9 Part # # 6 Main auger hangar bearing KML-UCHA Description Bearing with hangar type flange # 7 Main auger top bearing SA bearing 1 1/4" F bolt flange # 8 Cross auger drive SA bearing 1 1/4 PF flangettes for 2" bearing 60B25HF 1 1/4" #60-25 tooth sprocket 60B15HF 1 1/4" #60-15 tooth sprocket 60 1 rl chain 29" #60 chain 1/4" x 2" roll pin RH 9" x 9" x 1-7/8 x 3/16 Right hand flighting 5' long LH9" x 9" x 1-7/8 x 3/16 Left hand flighting 5' long # 9 Cross auger bearing SA FL (1 1/4") bearing bolt flange # 10 Roller drive & bearings SA bearing 2" F210D SPE bolt flange ductile Q1 2 NTL Split taper bushing # 11 Roller Chain Drive H50B13F 1" kw2ss 50B13 1" hole #50 1 rl chain 50" #50 reg chain 50B70F 50B70 1 1/2" hole H50B15F 1 1/2" kw 2SS 50B15 1 1/2" hole #50 1 rl chain 61" #50 reg chain H60B13F 1 1/2" kw 2ss 60B13 1 1/2" hole 60B96X2PB-brg 2" 60B96 2" hole #60 1 rl chain 90 3/4" #60 reg chain #60 cl & #60 os #60 connector & off set link S210-A113 Spindle HA220-1 Hub and caps

10 # 12 Axle Part # 42655UC1 R50642 ST235-80/R16 Description Hub #42 Spindle Tires # 13 Misc Q45-4E-FISN 4 Bank valve F1020-S Flow control BMR50-H4CS Motor 40AGU08-10HYS 4X8 Cylinder 25 AGU /2 X 24 Cylinder F K topwind dropleg jack S1018D 1/2" plug S1018J 1 1/4" plug 2" x 5' strap c/w hook Roller straps # 14 Hoses T2SN6C20FJ90CFJC T2SN6C118FJCFJ45C T2SN6C124FJCFJ45C T2SN6C110FJCFJC T2SN6C82FJCFJC T2SN8C240MPDFJ90D T2SN6C48FJCFJC 20" Hose 118" Hose 124" Hose 110" Hose 82" Hose 240" Hose 48" Hose Lower & upper auger flighting 14OD x 14 pitchx 3 1/2ID x 1/4 ga Flighting Length 74" lower Roller drive cover Adjustable cover center latch 6.4" Striker for