- PDF Free Download

Size: px

Start display at page:

Download ""

Clement Sanders
5 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory ACCESSORY HANDSFREELINK Application 2010 CR-V Publications No. AII Issue Date AUG 2009 PARTS LIST HFL Attachment Kit P/N 08E02-SWA-130 (Ivory) P/N 08E02-SWA-170 (Gray) P/N 08E02-SWA-180 (Quartz) HFL trim Template Fuse label HFL bracket 5A Fuse 4 EPT sealers HFL harness 5 Wire ties HFL subharness 4 Screws, 3 x 10 mm 2 Double-sided tapes 2 Washer screws, 4 x 12 mm HFL retainer Bushing Screw 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0908) 08E02-SWA of 14

2 Rubber bumper Clip Needle nose pliers Steel wire Rubber mallet Eye protection (face shield, safety goggles, etc.) Illustration of the HFL Installed on the Vehicle HFL Kit P/N 08E00-E CONTROL UNIT HFL HARNESS Switch Control unit HFL SUBHARNESS 5A FUSE Accessory User s Information Manual AB INSTALLATION TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Shop towel Isopropyl alcohol Diagonal cutters Ratchet 10 mm and 14 mm Sockets 10 mm Combination wrench Utility Knife T-15 and T-25 Torx wrench Felt-tip pen Masking tape Pushpin Drill 3 mm, 4.5 mm, 6 mm, 9 mm, and 10 mm Drill bits 20 mm Hole saw Plastic trim tool T/N SILTRIMTL 10 Scissors Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the audio unit and the navigation system, then write down the radio presets. 2. Disconnect the negative cable from the battery. 2 of 14 AII (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

3 3. Remove the right and left map light lenses (four retaining tabs each). Do not damage the lenses. 5. Remove the cover from the left sun visor (four retaining tabs). 4 RETAINING TABS 4 RETAINING TABS 4 RETAINING TABS LEFT MAP LIGHT LENS COVER LEFT SUN VISOR RIGHT MAP LIGHT LENS PLASTIC TRIM TOOL AD 4. Remove the roof console (four bolts and unplug the vehicle connectors). 2 TORX SCREWS B 6. Remove the left sun visor (two T-25 Torx screws). 7. Using a flat-tip screwdriver wrapped with a shop towel, remove the right and left sun visor holders. LEFT SUN VISOR HOLDER CONNECTORS Push. 2 SILVER BOLTS 2 BLACK BOLTS Y Turn. SHOP TOWEL FLAT-TIP SCREWDRIVER 2 SUN VISOR HOLDERS RIGHT SUN VISOR HOLDER AB 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0908) 3 of 14

4 8. Peel back the weatherstrip as shown. 11. Peel back the weatherstrip as shown. RETAINING TAB Collapsed. Remains on the vehicle panel. 2 S RETAINING TAB Lightly tap. BODY PIN Comes off from the clip. BODY Pushed deep behind the vehicle panel. Pull. BODY WEATHERSTRIP Peel back. AREA MARKED SIDE CURTAIN AIRBAG WEATHERSTRIP Peel back. LEFT A-PILLAR TRIM B SHOP TOWEL 12. Remove the left A-pillar trim (two clips). 13. Remove the left front door sill trim (three clips). LEFT A-PILLAR TRIM Tap straight down with rubber mallet. RUBBER MALLET AX 3 S 9. Using a rubber mallet wrapped with a shop towel, lightly tap the area marked SIDE CURTAIN AIRBAG on the top of the A-pillar trim to push in the vehicle clip. Make sure to aim the mallet straight down, not at an angle. 10. Remove the clip from the vehicle panel. LEFT FRONT DOOR SILL TRIM B 4 of 14 AII (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

5 14. Peel back the weatherstrip. WEATHERSTRIP Peel back. 2 S 17. Remove the driver s dashboard lower cover (seven clips and two hooks). Be careful not to damage the clips and hooks. 7 S LEFT KICK PANEL B 15. Remove the left kick panel (two clips). 16. Remove the driver s undercover (turn the knob, one pin and one clip). DRIVER S DASHBOARD LOWER COVER HOOK B Routing the HFL Subharness 18. Attach two 2A fuse labels to the two HFL subharness fuse cases. KNOB Turn. PIN 2A FUSE LABELS DRIVER S UNDERCOVER HFL SUBHARNESS B 2 HFL SUBHARNESS FUSE CASES B 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0908) 5 of 14

6 19. Plug the HFL subharness 6-pin connector into the 6-pin opening in the fuse box. FRONT VIEW FUSE BOX 6-PIN CONNECTOR 21. Wrap a piece of steel wire around the HFL subharness 4-pin connector and route it to the left A-pillar trim opening. Remove the steel wire. STEEL WIRE Wrap. LEFT A-PILLAR TRIM 4-PIN CONNECTOR 6-PIN HFL SUB HARNESS 6-PIN CONNECTOR STEEL WIRE Remove. FUSE BOX 6-PIN BB 20. If another accessory is already plugged into the 6-pin connector, remove the dummy connector from the 6-pin connector taped to the HFL subharness. Plug the other accessory 6-pin connector into the HFL subharness and plug the HFL subharness into the fuse box. Repeat this step so that these accessories are connected in the following order: (HFL Automatic Day/Night Mirror Trailer Hitch). FUSE BOX FUSE BOX CB 22. Remove the vehicle ground bolt. Place the HFL subharness ground terminal over the vehicle ground terminal, and secure them with the bolt. 2 6-PIN CONNECTORS GROUND TERMINAL GROUND BOLT DUMMY CONNECTOR GROUND TERMINAL ACCESSORY 6-PIN CONNECTOR AE FUSE BOX DB 6 of 14 AII (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

7 23. Route the HFL subharness as shown. 2 1-PIN CONNECTORS PARKING BRAKE 28. Route the HFL subharness along the left A-pillar and secure it to the vehicle harness with four wire ties. LEFT A-PILLAR PARKING BRAKE CONNECTOR 4 WIRE TIES HARNESS EPT SEALER AB EPT SEALER Cut in half. 1-PIN CONNECTORS PARKING BRAKE BB 24. Unplug the parking brake switch 1-pin connector, and plug it into the HFL subharness 1-pin connector. 25. Plug the HFL subharness 1-pin connector into the parking brake switch. 26. Cut one EPT sealer in half, and wrap one piece of EPT sealer around the 1-pin connectors as shown (The other half will be used in step 66). 27. Secure the HFL subharness to the vehicle harness with one wire tie. HARNESS WIRE TIE FUSE BOX CB 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0908) 7 of 14

8 29. Route the HFL subharness to the roof console opening. 32. Wrap the two remaining EPT sealers at the indicated position around the HFL subharness as shown. EPT SEALER 2 EPT SEALERS HEADLINER CURVED EPT SEALER Cut. BRACKET FRONT END OF THE BB 33. Tuck the HFL subharness between the vehicle panel and the headliner. Be careful not to crease the headliner. Installing the Control Unit 34. Using scissors, cut out template A and template B AB 30. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the EPT sealer will attach. 31. Cut one EPT sealer in half, and cut one piece in half again. Attach one piece of EPT sealer to the vehicle bracket as shown above. TEMPLATE TEMPLATE A SCISSORS TEMPLATE B AE 8 of 14 AII (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

9 35. Remove the damper (two screws). SUNGLASS HOLDER 39. Attach masking tape on to the roof console as shown. HOLE BUSHING PIN SCREW 9 mm DRILL BIT CAMSET LOCK 2 SCREWS DAMPER 2 RETAINING TABS AE MASKING TAPE DRILL BE 36. Remove the sunglass holder from the roof console (one screw and one vehicle bushing). 37. Remove the pin and remove the camset lock (two retaining tabs). 38. Remove the console light from the roof console (four retaining tabs). 40. While wearing eye protection, enlarge the hole on the roof console with a 9 mm drill bit. 41. Remove the masking tape. 42. Attach masking tape to the roof console as shown. MASKING TAPE 4 RETAINING TABS AE LIGHT AE 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0908) 9 of 14

10 43. Attach template A to the roof console at the indicated position with masking tape. 47. Using masking tape, attach the template B to the roof console at the indicated position. PUSHPIN CENTER PUSHPIN FELT-TIP PEN FELT-TIP PEN 4 MARKS TEMPLATE B MARK MASKING TAPE MASKING TAPE PUSHPIN 2 MARKS TEMPLATE A AE CENTER AE 44. Using a felt-tip pen, mark the center of the roof console as shown. 45. Using a pushpin, mark the roof console at two locations according to template A. Remove template A. 46. While wearing eye protection, drill two 4.5 mm holes at the locations marked in step 45. Remove any burrs. 48. Using a pushpin, pierce the roof console at four locations according to template B. 49. Using a felt-tip pen, mark the roof console along template B. Remove template B. 4.5 mm DRILL BIT DRILL 2 MARKS AE 10 of 14 AII (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

11 50. While wearing eye protection, drill four 3 mm holes at the four locations marked in step Using a utility knife, cut along the mark you made in step 49. Remove any burrs. 20 mm HOLE SAW DRILL 3 mm DRILL BIT Mark made in step 49. UTILITY KNIFE 4 MARKS 3 mm 6 mm 10 mm DRILL BIT Cut out. DRILL Cut out AE DRILL 54. Remove the masking tape attached in step Using isopropyl alcohol on a shop towel, thoroughly clean the areas indicated below. Remove the adhesive backing from two double-sided tapes and attach them on the control unit as shown AE 51. Enlarge the lower two 3 mm holes drilled in step 50 with a 6 mm drill bit and then with a 10 mm drill bit as shown. 52. Enlarge the other two 3 mm holes drilled in step 50 with a 20 mm hole saw as shown. CONTROL UNIT ADHESIVE BACKING 2 DOUBLE-SIDED TAPES ADHESIVE BACKING 10 mm 10 mm CONTROL UNIT Clean with isopropyl alcohol BE 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0908) 11 of 14

12 56. Plug the HFL harness 22-pin connector into the control unit. CONTROL UNIT CENTER 59. Bend the switch terminal as shown. SPEAKER TERMINAL Bend. CONTROL UNIT Do not cover these installation holes. TERMINAL HFL HARNESS HFL TRIM 2 ADHESIVE BACKINGS Remove. HFL HARNESS 22-PIN CONNECTOR AE 57. Using isopropyl alcohol on a shop towel, thoroughly clean the areas where the double-sided tapes will attach. Remove the adhesive backings from the control unit and attach the control unit to the indicated position on the roof console. Do not cover the installation holes with the control unit. 58. Secure the HFL bracket to the holes made on the roof console in step 46 with two 4 x 12 mm washer screws. Holes drilled in step 46. HFL RETAINER HFL RETAINER 4 SCREWS, 3 x 10 mm RUBBER BUMPER AD 60. Push the rubber bumper through the indicated hole in the HFL retainer. 61. Assemble the HFL retainer, switch, and HFL trim with four 3 x 10 mm screws. 2 WASHER SCREWS, 4 x 12 mm HFL BRACKET AE 12 of 14 AII (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

13 62. Plug the HFL harness 20-pin connector into the switch. 67. Tuck the 4-pin connectors behind the roof console opening as shown. SCREW (reused) 4-PIN CONNECTORS BUSHING (reused) LIGHT BUSHING CONNECTORS HFL HARNESS 20-PIN CONNECTOR HFL HARNESS SCREW AE 63. Install the switch assembled in step 61 to the roof console with the screw and vehicle bushing removed in step Reinstall the console light into the roof console. 65. Hold the roof console close to the roof console opening, and plug the HFL harness 4-pin connector into the HFL subharness 4-pin connector. EPT SEALER Cut in step 26. HFL HARNESS 4-PIN CONNECTOR 2 BLACK BOLTS 2 SILVER BOLTS BB 68. Reinstall the roof console. Installing the Fuse 69. Install the 5A fuse into the Number 27 slot on the fuse box. HFL SUB HARNESS 4-PIN CONNECTOR FRONT VIEW FUSE BOX EPT SEALER Number 27 SLOT 4-PIN CONNECTORS 5A FUSE AB 66. Wrap the piece of EPT sealer cut in step 26 around the 4-pin connectors. FUSE BOX BB 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0908) 13 of 14

14 70. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the fuse label will attach. FUSE LABEL 5A FUSE LABEL 5A FUSE LABEL 73. Position the clip perpendicular to the hole on the left A-pillar. Install the clip by lightly pushing the left A-pillar trim at the area marked SIDE CURTAIN AIRBAG. Be sure that the airbag is not pinched with the clip. Do not push too hard on the trim. No. 27 LEFT A-PILLAR PANEL DRIVER S SIDE UNDERCOVER AB 71. Attach the 5A fuse label to the Number 27 slot on the driver s undercover. Reinstalling the Left A-Pillar Trim 72. Check that the left A-pillar trim and the left A-pillar trim pin are not damaged, and install the new clip on the pin. LEFT A-PILLAR Removed in step 10. NEW AREA MARKED SIDE CURTAIN AIRBAG LEFT A-PILLAR TRIM Y 74. Check that all wire harness are routed properly and all connectors are plugged in. 75. Reinstall all remaining parts. Check that all clips and other fasteners are installed securely. 76. Reconnect the negative cable to the battery. 77. Enter the customer s radio anti-theft code, and reset the radio station presets. 78. Reset the clock. LEFT A-PILLAR TRIM PIN H 14 of 14 AII (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 38137-38714 Accessory HandsFreeLink 2008 ODYSSEY Issue Date JAN 2008 PARTS LIST Attachment Kit P/N 08E02-SHJ-100B trim Fuse label Fuse