- PDF Free Download

Size: px

Start display at page:

Download ""

Lizbeth Wilkerson
5 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory Application Publications No. XM RADIO SYSTEM CIVIC 2- AND 4-DOOR (Si) AII Issue Date AUG 2007 PARTS LIST XM Radio Attachment (sold separately): P/N 08B15-SNA-100B 7 Wire ties with clip Bus cable 12 Cushion tapes Front bracket 8 EPT sealers Rear bracket XM Antenna (sold separately): P/N 08A15-0J1-100 Antenna Clip Unit (sold separately): P/N 08A15-3J Pan screws XM Satellite Radio unit 4 Washers 3 Flange bolts 2-Port Bus Cable (sold separately): P/N 08A31-0F1-000 Cover seal 2-Port bus cable 20 Wire ties 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII (0708) 08B15-SVB-1B of 19

2 TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Utility knife Tape measure Shop towel Scissors Ratchet 8 mm, 10 mm, and 14 mm Socket 8 mm, 10 mm, and 14 mm Combination wrenches Isopropyl alcohol Rubber mallet Masking tape AUDIO UNIT XM RADIO UNIT Illustration of the XM Radio System Installed on the Vehicle H 2-door: Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. 3. Remove the passenger s dashboard lower cover (four clips and two pins). XM RADIO UNIT H 4-door: 2 PINS XM RADIO UNIT H 4 CLIPS PASSENGER S DASHBOARD LOWER COVER T 2 of 19 AII (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

3 4. Remove the two bolts under the glove box. 7. Remove the inside cover from the front console pocket (two tabs). 2 STOPS GLOVE BOX SHIFT LEVER S" or "2 POSITION FRONT CONSOLE POCKET 2 BOLTS T 2 TABS INSIDE COVER T 5. Open and remove the glove box (two stops). 6. Remove the driver s dashboard lower cover (eight clips). 8. Lower the tilt lever, then pull the steering wheel toward you. COMBINATION SWITCH SHOP TOWEL SHIFT LEVER STEERING WHEEL DRIVER S DASHBOARD LOWER COVER 8 CLIPS T TILT LEVER SHOP TOWEL H 9. To protect the dashboard area, put shop towels over the steering wheel and shift lever American Honda Motor Co., Inc. - All Rights Reserved. AII (0708) 3 of 19

4 10. Apply masking tape to the meter panel as shown, and remove the instrument panel (one self-tapping screw, 11 clips, and one connector). 12. Remove the weatherstrip from the opening edge of the right front door in the area shown. METER PANEL MASKING TAPE FRONT PILLAR PIN FRONT PILLAR TRIM CLIP Strike perpendicularly. CLIP RUBBER MALLET SELF-TAPPING SCREW 11 CLIPS B RIGHT FRONT PILLAR TRIM WEATHERSTRIP H 11. Apply masking tape to the instrument panel as shown. Remove the center panel (two bolts, eleven retaining clips, vehicle connectors, and the aspirator hose). 13. Push the clip into the vehicle side by striking the top of the right front pillar trim in the part marked as SIDE CURTAIN AIRBAG with the rubber mallet perpendicular to the vehicle. Then remove the clip. 5 CLIPS ASPIRATOR HOSE MASKING TAPE CONNECTORS CENTER PANEL 6 CLIPS BOLTS T 4 of 19 AII (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

5 14. Remove the weatherstrip in the area shown. Remove the right front pillar trim (two clips). 4-door: 15. Remove the cap from the right sunvisor (four retaining tabs). 2 CLIPS RIGHT FRONT PILLAR TRIM CONNECTOR 4 RETAINING TABS CAP SUNVISOR HOLDER TORX SCREW RIGHT SUNVISOR H 2-door: 2 CLIPS RIGHT FRONT PILLAR TRIM WEATHERSTRIP T 16. Remove the right sunvisor (two T25 TORX screws, and unplug the vehicle connectors). 17. Remove the sunvisor holder. Turn the holder 90, then pull it out. 18. Remove the center console cover. A/T: Remove the center console cover (five clips). 3 CLIPS CENTER CONSOLE COVER WEATHERSTRIP H PARKING BRAKE LEVER (Pull up completely.) SHIFT LEVER ( N position) 2 CLIPS T 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII (0708) 5 of 19

6 M/T: Pull down on the shift boot. Remove the shift knob by rotating counterclockwise. 19. Open the center console lid, and remove the mat. 4 BOLTS CLIP SHIFT KNOB MAT PARKING BRAKE LEVER (Pull up completely.) CLIP CENTER CONSOLE LID SHIFT BOOT H Remove the center console cover (five clips). CENTER CONSOLE CONNECTOR T 3 CLIPS CENTER CONSOLE COVER 20. Remove the center console (four bolts, two clips, and the vehicle connector). 2-door: Go to step door: Go to step CLIPS H 6 of 19 AII (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

7 2-door: 21. Remove the bolt, and then remove the rear seat cushion (two hooks). 23. Remove the trunk weatherstrip in the area shown. 3 HOOKS 2 CLIPS BOLT REAR TRIM PANEL TRUNK WEATHERSTRIP HOOKS REAR SEAT H 22. Open the trunk lid. Fold the rear seatback forward by pulling the levers under the rear parcel shelf. Remove the trunk floor mat (two clips) H 24. Remove the rear trim panel (two clips and three hooks). 25. Remove the weatherstrip. Remove the five clips and then the trunk right side trim panel. Then go to step 34. REAR SEATBACK CLIPS CLIP WEATHERSTRIP LEVER 2 CLIPS LEVER TRUNK FLOOR MAT H TRUNK RIGHT SIDE TRIM PANEL 3 CLIPS (Turn the center pin counterclockwise to remove.) H 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII (0708) 7 of 19

8 4-door: 26. Remove the bolt, and then remove the rear seat cushion (two hooks). 28. Remove the right rear side step trim (four clips and three retaining tabs). 4 CLIPS 3 RETAINING TAB BOLT FRONT HOOK REAR SEAT T RIGHT REAR SIDE STEP TRIM T 27. Remove the bolt and then the right seat side bolster. 29. Open the trunk lid. Fold the rear seatback forward by pulling the levers under the rear parcel shelf. RIGHT SEAT SIDE BOLSTER REAR SEATBACK LEVER 2 CLIPS BOLT T TRUNK FLOOR MAT 30. Remove the trunk floor mat (two clips) T 8 of 19 AII (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

9 31. Remove the weatherstrip in the area shown. 3 HOOKS REAR TRIM PANEL Routing the Bus Cable 34. Route the bus cable from the trunk as shown. 2-door: SEAT BRACKET 4 CLIPS TRUNK WEATHERSTRIP T 32. Remove the four clips and then the rear trim panel (three hooks). 33. Remove the weatherstrip. Remove the five clips, and then remove the trunk right side trim panel. CLIP (Turn the center pin counterclockwise to remove.) 4-door: REAR SEATBACK H CLIPS WEATHER STRIP BRACKET BUS CABLE TRUNK RIGHTSIDE TRIM PANEL CLIP (Turn the center pin counterclockwise to remove.) T RIGHT REAR SEATBACK H 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII (0708) 9 of 19

10 35. Lift up and lock the rear seatback, then remove the clip to pull back the floor carpet. Routing the Antenna Cable 38. Using isopropyl alcohol on a shop towel, clean the area shown on the inside of the windshield. FLOOR CARPET CLIP INSIDE 3 mm 10 mm Route under the floor carpet H 36. Route the bus cable forward under the floor carpet. 37. Route the bus cable foward along the vehicle harness, then pull the bus cable connector out of the dash opening. WINDSHIELD 4 ADHESIVE BACKINGS H DASH OPENING 39. Remove the adhesive backings from the antenna, and attach the antenna to the windshield at the location shown. Install the antenna by applying sufficient pressure. DASH OPENING HARNESS H 10 of 19 AII (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

11 40. Using isopropyl alcohol on a shop towel, clean the area shown on the outside of the windshield. OUTSIDE 44. Route the antenna cable down behind the dashboard stay and towards the glove box. Using three wire ties, secure the antenna cable to the vehicle harness. 5 mm 5 mm CABLE HARNESS WIRE TIES DASHBOARD STAY MARK on the front window ADHESIVE BACKING COVER SEAL H 41. Remove the adhesive backing from the cover seal, then attach to the location shown. 42. With scissors, cut three EPT sealers in half. EPT SEALER (Cut in half.) BRACKET EPT SEALER (1/2) H 45. Using scissors, cut one EPT sealer in half. Attach one of the cut pieces of the EPT sealer to the vehicle bracket. 46. In the glove box opening, route the antenna cable along the vehicle harness and towards the audio unit opening. CABLE HARNESS EPT SEALER (6 pieces) PASSENGER S A-PILLAR CABLE H 43. Route the antenna cable down along the passenger s A-pillar. Using the six pieces of cut EPT sealer, secure the antenna cable to the A- pillar panel in the areas shown. WIRE TIE H 47. Using one wire tie, secure the antenna cable to the vehicle harness American Honda Motor Co., Inc. - All Rights Reserved. AII (0708) 11 of 19

12 48. Route the antenna cable down along the bus cable as shown. WIRE TIES 52. Pull back the carpet. Using isopropyl alchohol on a shop towel, clean the areas where the cushion tapes will be applied. Route the antenna cable along the bus cable. Using two cushion tapes, secure the bus and antenna cables to the floor panel in the areas shown. 300 mm WIRE TIES CONNECTOR CABLE WIRE TIES CABLE H Pull back. 49. Using six wire ties, secure the bus cable and antenna cable to the vehicle harness as shown. 50. Route the antenna cable along the bus cable. Using three wire ties, secure the bus and antenna cables to the vehicle harness. HARNESS TAPE CABLE SIDE VIEW H HARNESS TAPE 53. Using three wire ties, secure the bus and antenna cables to the vehicle harness in the areas shown. 2-door: Go to step door: Go to step 56. WIRE TIE CABLE TAPE H 51. Using isopropyl alchohol on a shop towel, clean the areas shown where the cushion tapes will be applied. Secure the bus and antenna cables to the floor with three cushion tapes. 12 of 19 AII (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

13 2-door: 54. Route the antenna cable along the bus cable. Using three wire ties, secure the bus and antenna cables to the vehicle harness in the areas shown. 4-door: 56. Route the antenna cable along the bus cable. With two wire ties, secure the bus and antenna cables to the vehicle harness in the areas shown. AND CABLE AND CABLE BRACKET TAPE WIRE TIES CABLE TAPE TAPE WIRE TIE TAPE RIGHT REAR SEATBACK H 55. Using isopropyl alchohol on a shop towel, clean the areas where the cushion tapes will be applied. Using three cushion tapes, attach the bus and antenna cables to the floor panel in the areas shown. Then go to step 58. HARNESS H 57. Using isopropyl alchohol on a shop towel, clean the areas where the cushion tapes will be applied. With four cushion tapes, secure the bus and antenna cables to the floor panel in the areas shown American Honda Motor Co., Inc. - All Rights Reserved. AII (0708) 13 of 19

14 58. Using isopropyl alchohol on a shop towel, attach EPT sealer to the trunk right inner panel in the area shown. 2-door: EPT SEALER RIGHT TRUNK INNER PANEL Clean. Installing the XM Radio Unit 59. Using four pan screws and four washers, install the front and rear brackets to the XM radio unit. 2-door: Go to step door: Go to step PAN SCREWS FRONT BRACKET REAR BRACKET 4 WASHERS XM RADIO UNIT Clean. EPT SEALER H 4-door: H TRUNK RIGHT INNER PANEL Clean. EPT SEALER H 14 of 19 AII (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

15 2-door: 60. Route the Bus and antenna cables behind the trunk right inner panel. 63. Loosely install three flange bolts to the front and rear brackets. On the front bracket, use the B - marked holes. TAPE TRUNK RIGHT INNER PANEL CABLE 1-PIN CONNECTOR CABLE RIGHT TRUNK INNER PANEL FRONT BRACKET ELONGATED HOLE XM RADIO UNIT REAR BRACKET XM RADIO UNIT FLANGE BOLT 14-PIN CONNECTOR H 61. Plug the bus cable connector and the antenna cable connector into the XM radio unit. "B"-MARKED HOLE FLANGE BOLT H 62. Using one cushion tape, secure the bus and antenna cables to the XM radio unit. 64. Place the XM radio assembly on the back of the trunk right inner panel. Set the three flange bolts into the elongated holes in the body panel. 65. Tighten the three flange bolts American Honda Motor Co., Inc. - All Rights Reserved. AII (0708) 15 of 19

16 66. Using one wire tie with clip, secure the bus and antenna cables in the area shown. WIRE TIE WITH CLIP (in step 68) TAPE XM RADIO UNIT 4-door: 69. Plug the bus cable connector and the antenna cable connector into the XM radio unit. TAPE RIGHT TRUNK INNER PANEL CABLE CABLE 1-PIN CONNECTOR Bundle the excess cables. WIRE TIE WITH CLIP (in step 66) H XM RADIO UNIT 67. Secure the bus and antenna cables to the trunk right inner panel in the area shown using one cushion tape. 68. Using two wire ties with clips, bundle the excess bus and antenna cables.then, go to step PIN CONNECTOR H 70. Using one cushion tape, secure the antenna cable to the XM radio unit in the area shown. 16 of 19 AII (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

17 71. Loosely tighten three flange bolts to the front and rear brackets. On the front bracket, use the A - marked holes. 74. Using one wire tie with clip, secure the bus and antenna cables in the area shown. RIGHT TRUNK INNER PANEL ELONGATED HOLES XM RADIO UNIT WIRE TIE WITH CLIP (in step 76) WIRE TIE WITH CLIP (in step 75) FRONT BRACKET FLANGE BOLT REAR BRACKET WIRE TIE WITH CLIP (in step 74) XM RADIO UNIT "A"-MARKED HOLE 72. Place the XM radio assembly to the back of the right trunk inner panel. Set the three flange bolts into the elongated holes in the body panel. 73. Tighten the three flange bolts. FLANGE BOLT H Bundle the excess cables H 75. Using three wire ties with clips, secure the bus and antenna cables to the holes on the right trunk inner panel. 76. Using two wire ties with clips, bundle the excess bus cable and antenna cables, then tighten securely. Go to step American Honda Motor Co., Inc. - All Rights Reserved. AII (0708) 17 of 19

18 If the vehicle you re working on is equipped with a CD changer, go to step 77; otherwise, go to step Plug the 2-port bus cable connectors in the two bus cables. 79. Plug the bus cable connector into the audio unit (or navigation unit if equipped). Audio Unit for 4-door: AUDIO UNIT 2-PORT H Audio Unit for 2-door: 2 EPT SEALERS H AUDIO UNIT 78. Attach two EPT sealers around the two plugged connectors H Navigation Unit: NAVIGATION UNIT H 18 of 19 AII (0708) 2007 American Honda Motor Co., Inc. - All Rights Reserved.

19 80. Connect the vehicle connectors to the center panel, and reinstall the center panel. CENTER PANEL CONNECTORS 82. Check that all wire harnesses are routed properly and all connectors are plugged in. 83. Reconnect the negative cable to the battery. 84. Enter the customer s radio anti-theft code, and reset the radio station presets. 85. Set the clock. 86. Check the operation of the XM radio system according to the vehicle owner s manual. 87. Reinstall all removed parts. BOLTS (Reused.) H 81. Replace the old clip on the right front pillar trim with a new one. NEW CLIP OLD CLIP (Discard.) RIGHT FRONT PILLAR TRIM H 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII (0708) 19 of 19

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory XM RADIO SYSTEM Application 2009 CIVIC 2-AND 4-DOOR (Si) Publications No. AII 40186 Issue Date AUG 2008 PARTS LIST XM Radio Attachment (sold separately): P/N 08B15-SNA-100B