INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Virgil Bryan
6 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory XM RADIO SYSTEM Application 2009 CIVIC 2-AND 4-DOOR (Si) Publications No. AII Issue Date AUG 2008 PARTS LIST XM Radio Attachment (sold separately): P/N 08B15-SNA-100B Bus cable 20 Wire ties (2 Not used) Front bracket 7 Wire ties with clip (Some may not be used.) Rear bracket 12 Cushion tapes (Some may not be used.) Clip 8 EPT sealers (Some may not be used.) 4 Pan screws XM Antenna (sold separately): P/N 08A15-0J1-100 Antenna assy 4 Washers 3 Flange bolts Unit (sold separately): P/N 08A15-3J1-000 XM radio unit Cover seal 2008 American Honda Motor Co., Inc. All Rights Reserved. AII (0808) 08B15-SVB-1B of 20

2 2-Port Bus Cable (sold separately): P/N 08A31-0F Port bus cable Illustration of the XM Radio System Installed on the Vehicle 2-door vehicle: TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ruler Shop towel Scissors Ratchet 10 mm Socket 10 mm Combination wrench Isopropyl alcohol (Isopropyl alcohol, in a 60/40 solution with water) Rubber mallet Masking tape Diagonal cutters Plastic Trim Tool (T/N SILTRIMTL10) TORX bit 4-door vehicle: XM RADIO UNIT AR XM RADIO UNIT H 2 of 20 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved.

3 4. Remove the two bolts under the glove box. AUDIO UNIT 2 STOPPERS GLOVE BOX XM RADIO UNIT 2 BOLTS AR INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers AR 5. Open and remove the glove box (two stoppers). 6. Remove the driver s dashboard lower cover (eight clips). 1. Make sure you have the anti-theft codes for the audio and navigation system (if equipped), then write down the audio presets. 2. Disconnect the negative cable from the battery. 3. Remove the passenger s dashboard lower cover (four clips and two pins). DRIVER S DASHBOARD LOWER COVER 8 CLIPS T 2 PINS 4 CLIPS PASSENGER S DASHBOARD AH 2008 American Honda Motor Co., Inc. All Rights Reserved. AII (0808) 3 of 20

4 7. Remove the inside cover from the front console pocket (two tabs). 10. Apply masking tape to the meter panel as shown, and remove the meter panel (one self-tapping screw and 11 clips, and unplug the vehicle connectors). SHIFT LEVER S or 2 POSITION FRONT CONSOLE POCKET METER PANEL MASKING TAPE 2 TABS INSIDE COVER 8. Lower the tilt lever, then pull the steering wheel toward you. SHOP TOWEL COMBINATION SWITCH T CONNECTORS SELF-TAPPING SCREW 11 CLIPS AR 11. Apply masking tape to the instrument panel as shown. Remove the center panel (two bolts, 11 clips, and aspirator hose, and unplug the vehicle connectors). SHIFT LEVER 5 CLIPS ASPIRATOR HOSE MASKING TAPE CONNECTORS STEERING WHEEL SHOP TOWEL TILT LEVER CENTER PANEL 6 CLIPS BOLTS AR H 9. To protect the dashboard area, put shop towels over the steering wheel and shift lever. 4 of 20 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved.

5 12. Pull the weatherstrip off in the area shown. FRONT PILLAR 14. Pull the weatherstrip off in the area shown. And remove the right front pillar trim (two clips). 4-door vehicle: PIN 2 CLIPS RIGHT FRONT PILLAR TRIM CLIP FRONT PILLAR TRIM CLIP Strike perpendicularly. RUBBER MALLET WEATHERSTRIP RIGHT FRONT PILLAR TRIM WEATHERSTRIP AR 2-door vehicle: AR 13. Push the clip into the vehicle side by striking the top of the right front pillar trim in the part marked as SIDE CURTAIN AIRBAG with the rubber mallet perpendicularly to the vehicle. Then, remove the clip. 2 CLIPS RIGHT FRONT PILLAR TRIM WEATHERSTRIP AR 2008 American Honda Motor Co., Inc. All Rights Reserved. AII (0808) 5 of 20

6 15. Remove the cap from the right sunvisor (four retaining tabs). CONNECTOR (If equipped.) M/T Vehicle Pull down on the shift boot. Remove the shift knob by rotating counterclockwise. SHIFT KNOB 4 RETAINING TABS PARKING BRAKE LEVER (Pull up completely.) CAP RIGHT SUNVISOR 2 TORX SCREWS SUNVISOR HOLDER AR SHIFT BOOT 16. Remove the right sunvisor (two T25 TORX screws, and unplug the vehicle connector, if equipped). 17. Remove the sunvisor holder. Turn the holder 90, then pull it out. 18. Remove the center console cover. Remove the center console cover (five clips). 3 CLIPS CENTER CONSOLE COVER H A/T vehicle: Remove the center console cover (five clips). 2 CLIPS 3 CLIPS CENTER CONSOLE COVER 2 CLIPS H SHIFT LEVER N POSITION PARKING BRAKE LEVER (Pull up completely.) T 6 of 20 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved.

7 19. Open the center console lid, and remove the mat. 4 BOLTS CLIP 2-door vehicle: 21. In the passenger s compartment, remove the bolt and then rear seat cushion (two hooks). MAT BOLT CLIP CENTER CONSOLE LID CENTER CONSOLE CONNECTOR AH 20. Remove the center console (four bolts and two clips, and unplug the vehicle connector). 2-door vehicle: Go on to step door vehicle: Go to step 26. HOOKS AH 22. Open the trunk lid. Fold the rear seatback forward by pulling the levers under the rear shelf. Remove the trunk floor mat (two clips). REAR SEATBACK REAR SEAT CUSHION LEVER LEVER 2 CLIPS TRUNK FLOOR MAT AH 2008 American Honda Motor Co., Inc. All Rights Reserved. AII (0808) 7 of 20

8 23. Pull the trunk weatherstrip off in the area shown. 26. Remove the bolt and then rear seat cushion (two hooks). 3 HOOKS 2 CLIPS BOLT REAR TRIM PANEL TRUNK WEATHERSTRIP HOOKS REAR SEAT CUSHION T AH 24. Remove the rear trim panel (two clips and three hooks). 25. Pull the weatherstrip off. Remove the five clips and then the right trunk side trim panel. Go to step Remove the bolt and then the right seat side bolster. RIGHT SEAT SIDE BOLSTER CLIPS WEATHERSTRIP BOLT T RIGHT TRUNK SIDE TRIM PANEL 3 CLIPS (Turn the center pin in a counterclockwise direction to remove.) AH 4-door vehicle: 8 of 20 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved.

9 28. Remove the right rear side step trim (four clips and three retaining tabs). 31. Pull the weatherstrip off in the area shown. 3 HOOKS REAR TRIM PANEL 4 CLIPS 3 RETAINING TABS 4 CLIPS TRUNK WEATHERSTRIP RIGHT REAR SIDE STEP TRIM FRONT T 29. Open the trunk lid. Fold the rear seatback forward by pulling the levers under the rear shelf. REAR SEATBACK 2 LEVERS 2 CLIPS 32. Remove the rear trim panel (four clips and three hooks) T 33. Pull the weatherstrip off. Remove the five clips and then the right trunk side trim panel. CLIPS CLIPS (Turn the center pin counterclockwise to remove.) WEATHERSTRIP TRUNK FLOOR MAT 30. Remove the trunk floor mat (two clips) T RIGHT TRUNK SIDE TRIM PANEL CLIP (Turn the center pin counterclockwise to remove.) T 2008 American Honda Motor Co., Inc. All Rights Reserved. AII (0808) 9 of 20

10 Routing the Bus Cable 34. Route the bus cable from the trunk as shown. 4-door vehicle: 2-door vehicle: SEAT BRACKET BRACKET RIGHT REAR SEATBACK REAR SEATBACK AR 35. Lift up and lock the rear seatback, then remove the clip to pull back the floor carpet AH FLOOR CARPET CLIP Route under the floor carpet. BUS CABLE AH 36. Route the bus cable forward under the floor carpet. 10 of 20 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved.

11 37. Route the bus cable along the vehicle harness forward, then pull the bus cable connector out of the dash opening. Routing the Antenna Cable 38. With isopropyl alcohol on a shop towel, clean the area shown on the inside of the front window. DASH OPENING DASH OPENING INSIDE 3 mm (0.1 in.) 10 mm (0.4 in.) HARNESS FRONT WINDOW 4 ADHESIVE BACKINGS AR 39. Remove the adhesive backings from the antenna, and attach the antenna to the location shown. Apply sufficient pressure to completely contact AH 2008 American Honda Motor Co., Inc. All Rights Reserved. AII (0808) 11 of 20

12 40. Attach the masking tape to the location shown. 43. With scissors, cut three EPT sealers in half. OUTSIDE MASKING TAPE 6 mm (0.24 in.) EPT SEALER (Cut in half.) 5 mm (0.2 in.) Align with end of the masking tape. 6 HALF EPT SEALERS CABLE PASSENGER S A-PILLAR HOLES (Do not attach the EPT sealers.) AR COVER SEAL ADHESIVE BACKING AR 41. With isopropyl alcohol on a shop towel, clean the area shown on the outside of the front window. 42. Remove the adhesive backing from the cover seal, then attach to the location shown. Remove the masking tape. 44. Route the antenna cable down along the passenger s A-pillar. Using the six pieces of EPT sealer, secure the antenna cable to the A-pillar panel in the areas shown. NOTE: Do not attach the half EPT sealers to the vehicle holes, pay attention to the orientation of half EPT sealers. 12 of 20 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved.

13 45. With scissors, cut one EPT sealer in half. Attach one of the halved piece of the EPT sealer to the vehicle bracket. CABLE HARNESS WIRE TIES 49. Route the antenna cable down along the bus cable as shown. 300 mm (11.8 in.) WIRE TIES DASHBOARD STAY CONNECTOR WIRE TIES BRACKET EPT SEALER (1/2) H 46. Route the antenna cable down behind the dashboard stay and towards the glove box. Using three wire ties, secure the antenna cable to the vehicle harness. 47. In the glove box opening, route the antenna cable along the vehicle harness and towards the audio unit opening. CABLE 50. Using six wire ties, secure the bus cable and antenna cable to the vehicle harness as shown. 51. Route the antenna cable along the bus cable. Using three wire ties, secure the bus and antenna cables to the vehicle harness. CUSHION TAPE AR CABLE HARNESS HARNESS CABLE WIRE TIES CUSHION TAPES AR WIRE TIE H 48. Using one wire tie, secure the antenna cable to the vehicle harness. 52. Secure the bus and antenna cables to the floor panel using three cushion tapes in the areas shown after thorough cleaning with isopropyl alcohol on a shop towel American Honda Motor Co., Inc. All Rights Reserved. AII (0808) 13 of 20

14 53. Route the antenna cable along the bus cable. Turn over the floor carpet. Using two cushion tapes, secure the bus and antenna cables to the floor panel in the areas shown after thorough cleaning with isopropyl alcohol on a shop towel. 2-door vehicle: 55. Route the antenna cable along the bus cable. Using the two wire ties, secure the bus and antenna cables to the vehicle harness in the areas shown. WIRE TIES AND CABLE CABLE CABLE CUSHION TAPE Turn over. WIRE TIES CUSHION TAPES HARNESS CUSHION TAPE CABLE SIDE VIEW AR 54. Using three wire ties, secure the bus and antenna cables to the vehicle harness in the areas shown. 2-door vehicle: Go on to step door vehicle: Go to step BR 56. Using three cushion tapes, attach the bus and antenna cables to the floor panel in the areas shown after thorough cleaning with isopropyl alcohol on a shop towel. Go to step of 20 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved.

15 4-door vehicle: 57. Route the antenna cable along the bus cable. With two wire ties, secure the bus and antenna cables to the vehicle harness in the areas shown. 59. Attach EPT sealers to the right trunk inner panel in the areas shown after thorough cleaning using isopropyl alcohol on a shop towel. 2-door vehicle: AND CABLE BRACKET EPT SEALER RIGHT TRUNK INNER PANEL Clean. WIRE TIES CUSHION TAPES RIGHT REAR SEATBACK Clean. EPT SEALER AR 4-door vehicle: HARNESS AR 58. With four cushion tapes, secure the bus and antenna cables to the floor panel in the areas shown after thorough cleaning using isopropyl alcohol on a shop towel. RIGHT TRUNK INNER PANEL Clean. EPT SEALER H 2008 American Honda Motor Co., Inc. All Rights Reserved. AII (0808) 15 of 20

16 Installing the XM Radio Unit 60. Using four pan screws and four washers, set the front and rear brackets to the XM radio unit. 2-door vehicle: Go on to step door vehicle: Go to step PAN SCREWS FRONT BRACKET 2-door vehicle: 61. Route the bus and antenna cables through the hole of the right trunk inner panel. CUSHION TAPE RIGHT TRUNK INNER PANEL CABLE 1-PIN CONNECTOR CABLE REAR BRACKET 4 WASHERS XM RADIO UNIT 14-PIN CONNECTOR XM RADIO UNIT AR H 62. Plug the bus cable connector and the antenna cable connector into the XM radio unit. 63. Using one cushion tape, secure the bus and antenna cables to the XM radio unit. 16 of 20 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved.

17 64. Loosely tighten three flange bolts to the front and rear brackets. On the front bracket, use the B marked holes. 67. Using one wire tie with clip, secure the bus and antenna cables in the area shown. RIGHT TRUNK INNER PANEL FRONT BRACKET ELONGATED HOLES XM RADIO UNIT REAR BRACKET WIRE TIES WITH CLIP in step 69 CUSHION TAPE XM RADIO UNIT FLANGE BOLT CUSHION TAPE Bundle the excess cables. B MARKED HOLE FLANGE BOLT AR 65. Place the XM radio assembly to the back of the right trunk inner panel. Set the three flange bolts into the elongated holes in the body panel. 66. Tighten the three flange bolts to secure. RIGHT TRUNK INNER PANEL WIRE TIE WITH CLIP in step BR 68. Using two cushion tapes, secure the bus and antenna cables to the right trunk inner panel in the area shown after thorough cleaning with isopropyl alcohol on a shop towel. 69. Using two wire ties with clip, bundle the excess of the bus and antenna cables, then tighten securely. Go to step American Honda Motor Co., Inc. All Rights Reserved. AII (0808) 17 of 20

18 4-door vehicle: 70. Plug the bus cable connector and the antenna cable connector into the XM radio unit. CUSHION TAPE RIGHT TRUNK INNER PANEL CABLE CABLE 1-PIN CONNECTOR 75. Using one wire tie with clip, secure the bus and antenna cables in the area shown. WIRE TIES WITH CLIP in step 77 WIRE TIES WITH CLIP in step 76 WIRE TIE WITH CLIP in step 75 XM RADIO UNIT 14-PIN CONNECTOR H 71. Using one cushion tape, secure the antenna cable to the XM radio unit in the area shown. 72. Loosely tighten three flange bolts to the front and rear brackets. On the front bracket, use the A marked holes. RIGHT TRUNK INNER PANEL Bundle the excess cables. XM RADIO UNIT AR 76. Using three wire ties with clip, secure the bus and antenna cables to the holes on the right trunk inner panel. 77. Using two wire ties with clip, bundle the excess of the bus cable and antenna cables, then tighten securely. ELONGATED HOLES RIGHT TRUNK INNER PANEL FRONT BRACKET XM RADIO UNIT FLANGE BOLT REAR BRACKET A MARKED HOLE FLANGE BOLT AR 73. Place the XM radio assembly to the back of the right trunk inner panel. Set the three flange bolts into the elongated holes in the body panel. 74. Tighten the three flange bolts to secure. 18 of 20 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved.

19 If the vehicle you re working on is equipped with CD Changer, go on to step 78; otherwise, go to step Plug the 2-port bus cable connectors in the two bus cables. Audio Unit for 2-door vehicle AUDIO UNIT S or 2-PORT 2-PORT 2 EPT SEALERS Navigation Unit H AR 79. Attach two EPT sealers around the two plugged connectors. NAVIGATION UNIT 80. Plug the bus cable connector into the audio unit. Audio Unit for 4-door vehicle or 2-PORT AUDIO UNIT AH or 2-PORT AR 2008 American Honda Motor Co., Inc. All Rights Reserved. AII (0808) 19 of 20

20 81. Plug the vehicle connectors to the center panel, and reinstall the center panel. CENTER PANEL CONNECTORS 83. Check that all wire harnesses are routed properly and all connectors are plugged in. 84. Reinstall all removed parts. 85. Connect the negative cable to the battery and check operation of all lights and other electrical accessories. 86. Enter the anti-theft codes for the audio system and the navigation system (if equipped), and reset the radio station presets. 87. Reset the clock on vehicles without navigation. 88. Check the operation of the XM radio system according to the vehicle s owner s manual. BOLTS (Reuse.) H 82. Replace the old clip on the right front pillar trim with a new one. NEW CLIP OLD CLIP (Discard.) RIGHT FRONT PILLAR TRIM AR 20 of 20 AII (0808) 2008 American Honda Motor Co., Inc. All Rights Reserved.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory XM RADIO SYSTEM Application 2011 CIVIC 2-AND 4-DOOR (EX, EX-L) Publications No. AII 44350 Issue Date AUG 2010 PARTS LIST XM Radio Attachment (sold separately): P/N 08B15-SNA-100A