INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Elijah Gilbert
5 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory USB ADAPTER Application 2014 INSIGHT Publications No. AII Issue Date OCT 2013 PARTS LIST USB Adapter Attachment Kit P/N 08B28-TM8-100A 6 mm Flange nut Control unit bracket Wire tie with clip USB cable 10 Wire ties USB cable A 5 Urethane tapes USB Adapter Kit P/N 08A28-0K1-100 Bus cable Control unit Grommet Bus Cable 2-Port P/N 08A31-0F Flange bolts, 5 x 7 mm Bus cable 2-port 6 x 12 mm Washer-bolt 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1310) 1 of 10

2 TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 10 mm Combination wrench Shop towel Scale File Isopropyl alcohol Utility knife Pushpin Drill 16 mm Hole saw Eye protection (face shield, safety goggles, etc.) 8 mm and 10 mm Socket Diagonal cutters Plastic trim tool T/N SILTRIMTL 10 3 mm Drill bit Tape Hammer (Wooden handle) INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the audio unit. 2. Disconnect the negative cable from the 12 volt battery. 3. Remove the passenger s dashboard undercover (three clips and two pins). 3 CLIPS Illustration of the USB Adapter in the Vehicle BUS A 2 PINS PASSENGER S DASHBOARD UNDERCOVER AE BE 2 of 10 AII (1310) 2013 American Honda Motor Co., Inc. All Rights Reserved.

3 4. Remove the glove box (one damper rod, two bolts, and two stops). STOP Push. STOP Push. 6. Remove the audio unit assembly: Reach under the dashboard, and remove the audio unit bolt. Using the sturdy wooden handle of a hammer, push the back of the audio unit forward to release the eight clips. Release the harness clip, and unplug the vehicle connectors. Carefully remove the audio unit without scratching the dashboard. AUDIO ASSEMBLY AUDIO HAMMER (WOODEN HANDLE) DAMPER ROD BOLTS AE 5. Remove the center lower trim (six clips, three retaining tabs, and unplug the vehicle connector). AUDIO ASSEMBLY CLIP GLOVE BOX 6 CLIPS 8 CLIPS AUDIO BOLT S 8D0901AD 3 RETAINING TABS CENTER LOWER TRIM 8D0902AD 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1310) 3 of 10

4 7. Insert the key into the shift lock release slot, push down on the key, and move the shift lever to the D position. Pull the parking brake lever all the way up. RELEASE BUTTON 9. Remove the rubber mat from the center console. RUBBER MAT COVER SHIFT LOCK RELEASE SLOT CENTER CONSOLE AY D POSITION 10. Remove the parking brake lever trim (two retaining tabs and one hook). PARKING BRAKE LEVER TRIM 2 RETAINING TABS SHIFT LEVER HOOK PARKING BRAKE LEVER Pull up. 8. Remove the beverage holder. BEVERAGE HOLDER AY CENTER CONSOLE AY 4 of 10 AII (1310) 2013 American Honda Motor Co., Inc. All Rights Reserved.

5 11. Attach masking tape to the bottom edge of the instrument panel, around the shift lever, and around the parking brake lever. CENTER CONSOLE 2 CLIPS 14. Position the control unit bracket under the floor carpet as shown. CONTROL BRACKET 6 x 12 mm WASHER-BOLT 2 SCREWS INSTRUMENT PANEL BOLT MASKING TAPE WITH CLIP SHIFT LEVER PANEL PARKING BRAKE LEVER MASKING TAPE 8N1813AY FLOOR CARPET 6 mm FLANGE NUT 12. Carefully remove the center console (two clips and two screws). 13. Remove the rear bolt from the vehicle frame, and release the harness clip. SHIFT LEVER BOLT Reuse. WITH CLIP Cut. 15. Secure the control unit bracket to the vehicle frame with the vehicle bolt you removed in step 13, and with one 6 x 12 mm washer-bolt with 6 mm flange nut as shown. 16. Using diagonal cutters, cut and remove the original vehicle wire tie with clip. 17. Secure the vehicle harness to the bracket with one new wire tie with clip. CONTROL BRACKET FRAME CLIP BD WITH CLIP WITH CLIP BRACKET 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1310) 5 of 10

6 18. Install the control unit to the control unit bracket with three 5 x 7 mm flange bolts. Use a combination wrench to tighten the flange bolts. 20. Route the bus cable and the USB cable forward along the vehicle harness. CONTROL 3 FLANGE BOLTS, 5 x 7 mm CONTROL BUS WIRE TIE CONTROL BRACKET AD 19. Plug the bus cable 14-pin connector and the USB cable 4-pin connector (corrugated tube end) into the control unit as shown. CONTROL 21. Secure the bus cable and the USB cable to the vehicle harness with three wire ties. NOTE: Do not attach the wire ties to the yellow-taped portion of the vehicle harness. 22. Continue routing the bus cable and the USB cable forward as shown. AIR DUCT 4-PIN (CORRUGATED TUBE END) BUS 14-PIN BD PANEL URETHANE TAPE AD 23. Remove the air duct. Using isopropyl alcohol on a shop towel, clean the areas on the floor and the back of the air duct where the urethane tape will attach. 24. Secure the bus cable and the USB cable to the vehicle panel and air duct with two pieces of urethane tape, then reinstall the air duct. 6 of 10 AII (1310) 2013 American Honda Motor Co., Inc. All Rights Reserved.

7 25. At the center lower trim opening, route the bus cable toward the center panel opening, and route the USB cable toward the glove box opening. 27. Bundle the excess bus cable, and secure it to the vehicle frame with two wire ties. Bundle the excess. S USB CENTER LOWER TRIM CD 26. Align the bus cable 14-pin connector with the vehicle 24-pin connector, and secure the bus cable to the vehicle harness with one wire tie. CENTER LOWER TRIM FRAME 28. Route the USB cable into the glove box opening DD CENTER PANEL BUS Align. 24-PIN 14-PIN CD 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1310) 7 of 10

8 29. Secure the USB cable to the vehicle frame with one wire tie. 31. Get the glove box. Using a utility knife, cut out the insulator on the glove box at the measurement shown. 30 mm FRAME 45 mm INSULATOR Cut. GLOVE BOX 30. Secure the USB cable to the vehicle harness with one wire tie AD 32. Using a pushpin, pierce the glove box in two places at the measurements shown. 2 MARKS RIB 30 mm PUSHPIN 70 mm 15 mm 8N2512AE 8 of 10 AII (1310) 2013 American Honda Motor Co., Inc. All Rights Reserved.

9 33. While wearing eye protection, drill the two pierced marks in the glove box. First drill with a 3 mm drill bit, and finish with a 16 mm hole saw. Use a utility knife to cut between the two 16 mm holes. Remove any burrs. 35. Reinstall the glove box. Loosely install the two bolts. UTILITY KNIFE DRILL 3 mm DRILL BIT Cut off. 16 mm HOLE SAW 2 BOLTS Loosely install AD 2 MARKS 36. Plug the 4-pin connector on USB cable A into the USB cable 4-pin connector as shown. 8N2513AE 34. Route the 4-pin connector end of USB cable A through the grommet and the hole in the glove box. Seat the grommet into the hole in the glove box. URETHANE TAPE USB 4-PIN A 4-PIN A 4-PIN USB A 4-PIN S HOLE USB A 37. Wrap one urethane tape around the 4-pin connectors BY GROMMET BD 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1310) 9 of 10

10 38. Secure USB cable A and the 4-pin connectors to the vehicle harness with two wire ties. 4-PIN S 41. Plug the bus cable 14-pin connector or bus cable 2-port 14-pin connector into the audio unit, and reinstall the audio unit. AUDIO 14-PIN OR 2-PORT 14-PIN WIRE TIES USB A CD AUDIO 14-PIN AD 39. Reinstall the glove box. If the vehicle is equipped with another accessory that plugs into the 14-pin connector in the audio unit, continue with step 40, otherwise go to step Plug the bus cable 14-pin connector and the other accessory 14-pin connector into the bus cable 2-port 14-pin connectors. Wrap one piece of urethane tape around each 14-pin connector. 14-PIN URETHANE TAPE Wrap. 42. Check that all wire harnesses are routed properly and all connectors are plugged in. 43. Connect the negative cable to the battery. 44. Enter the anti-theft code for the audio unit, and reset the clock. 45. Reinstall all removed parts. 46. Turn the radio unit ON. Set the mode to USB by pressing AUX until USB is shown on the radio display. If USB NO DATA is on the display, the unit is working properly. CENTER PANEL 2-PORT 2-PORT 14-PIN S 14-PIN AB or OTHER ACCESSORY 14-PIN 10 of 10 AII (1310) 2013 American Honda Motor Co., Inc. All Rights Reserved.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory P/N 08E10-TA0-110A Application 2012 ACCORD 2- AND 4-DOOR Publications No. AII 46501 Issue Date AUG 2011 PARTS LIST Ambient Light Kit Fuse label 2 Ambient lights Washer