INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Warren Page
5 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII ODYSSEY Issue Date SEP 2004 PARTS LIST 15 Black wire ties Backup Sensor Attachment Kit P/N 08V67-SHJ-100A Backup sensor control unit 2 Small wire ties Buzzer 3 Long wire ties Switch 2 Cable clips Blind nut Backup sensor harness Washer-screw, 4 x 14 mm Flange bolt, 6 x 12 mm 2 Flange nuts 6 mm Buzzer bracket Fuse label Cushion Control unit bracket 2 EPT seals 2004 American Honda Motor Co., Inc. - All Rights Reserved. AII (0409) 08V67-SHJ of 12

2 Backup Sensor Kit Illustration of the Backup Sensor Installed on the Vehicle 2 Corner sensors SWITCH CONTROL UNIT 2 Center sensors CORNER 2 Spacers CENTER CORNER Y INSTALLATION TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver Small flat-tip screwdriver Felt-tip pen 10 mm Combination wrench 10 mm and 14 mm Socket Pushpin Ratchet 3 mm, 8 mm, Drill bit Eye protection (face shield, safety goggles, etc.) File Diagonal cutters Scissors Masking tape Tape measure Cardboard Isopropyl alcohol Shop towel 22 mm and 26 mm Holesaws Drill Utility knife Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 2 of 12 AII (0409) 2004 American Honda Motor Co., Inc. - All Rights Reserved.

3 3. Remove the rear bumper: Remove the three clips along the bottom of the bumper. Remove the six screws (three on each side) from the fenderwell area. Using a flat-tip screwdriver, pry out and remove the bumper bolt covers, then remove the four bumper bolts. With the help of an assistant, release the bumper from the fenderwell, and slide the bumper away from the vehicle. Set the bumper on a blanket. 5. Pull away the weatherstrip from the rear trim panel. Remove the rear trim panel (ten clips, and two screws). REAR TRIM CLIPS (10) SCREW S (4) SCREW WEATHERSTRIP Y SELF-TAPPING SCREWS (6) CLIPS (3) REAR COVERS (4) 6. Remove the spare tire cover (17 tabs). SIDE TRIM TABS (17) 4. Remove the driver s sliding door sill trim (five clips). CLIPS (5) DRIVER S SLIDING DOOR SILL TRIM SPARE TIRE COVER Y Y 2004 American Honda Motor Co., Inc. - All Rights Reserved. AII (0409) 3 of 12

4 7. Remove the anchor bolt and the anchor bolt cover, and take out the spare tire. 9. Remove the left second row seat belt upper anchor cover (two tabs). Remove the left second row seat belt upper anchor bolt. SPARE TIRE TAB ANCHOR 8. Remove the jack cover (2 tabs). ANCHOR COVER Y LEFT SECOND ROW SEAT BELT UPPER ANCHOR LEFT SECOND ROW SEAT BELT UPPER ANCHOR COVER Y SIDE 10. Pull away the weatherstrip from the left quarter pillar trim. Remove the left quarter pillar trim (two tabs and clip). TABS (2) WEATHERSTRIP LEFT QUARTER PILLAR TRIM JACK COVER Y SRS CLIP TAB Y 4 of 12 AII (0409) 2004 American Honda Motor Co., Inc. - All Rights Reserved.

5 11. Remove the left rear side trim panel: Remove the third row seat rail cover (three clips). CLIPS (3) THIRD ROW SEAT RAIL COVER 12. Remove the left rear pillar trim (one cover, one bolt, one clip, two tabs). CLIP TAB PILLAR TRIM COVER SIDE TRIM THIRD ROW SEAT Pull away the weatherstrip from the left rear side trim panel. Remove the second row seat belt lower anchor bolt Y Gently pull the panel out towards you to release the eight clips and four retaining clips, release the third row seat belt through the slit in the panel, and disconnect the rear accessory socket connector. 13. EX Model Only: Remove the two self-tapping screws, disengage the retaining tab, and pull out the power door control unit. Move the control unit out of the way. LEFT SIDE REAR POWER DOOR CONTROL UNIT TABS (4) CLIPS (8) SIDE TRIM WEATHERSTRIP SELF-TAPPING SCREW Y SIDE TRIM ACCESSORY SOCKET SECOND ROW SEAT BELT LOWER ANCHOR Y 2004 American Honda Motor Co., Inc. - All Rights Reserved. AII (0409) 5 of 12

6 14. At the left rear panel area, enlarge the panel hole to 8 mm. While wearing eye protection, drill the body panel using an 8 mm drill bit and a drill stop. 16. Using the isopropyl alcohol, thoroughly clean the areas where the cushion tape will attach. Using scissors, cut the cushion tape in half. Attach one of the two halves to the buzzer bracket. 10 mm TAPE CUSHION TAPE (Cut in half.) CUSHION TAPE BRACKET SIDE VIEW DRILL (8 mm drill bit) Y 15. Install the buzzer bracket to the buzzer using the 6 x 12 mm flange bolt and a 6 mm flange nut. BRACKET CUSHION TAPE BRACKET Y 6 x 12 mm FLANGE 17. Install the blind nut into the 8 mm hole you drilled. Attach the buzzer to the vehicle panel using the 4 x 14 mm washer screw. 6 mm FLANGE NUT Y 4 x 14 mm WASHER SCREW BLIND NUT Y 6 of 12 AII (0409) 2004 American Honda Motor Co., Inc. - All Rights Reserved.

7 Routing the Backup Sensor Harness 18. On the left rear outside of the vehicle, remove the vehicle grommet. From inside the cargo area, route the backup sensor harness out through the hole where the grommet was removed, as shown. GROMMET 21. Pull the weatherstrip away from the right rear side trim panel. Remove the one anchor screw, and gently pull out on trim panel to release the two clips. HATCH OPENING SEAL WEATHERSTRIP OUTSIDE INSIDE GROMMET ANCHOR SCREW GROMMET Y 19. Pull the harness grommet through the hole in the body panel, then seat the grommet in the hole. 20. Route the 13-pin connector end of the backup sensor harness along the cargo area to the right rear side trim panel. RIGHT REAR SIDE TRIM CLIP (2) RIGHT REAR SIDE TRIM Y 22. Behind the right rear side trim panel, disconnect the 13-pin connector from the junction box. Insert the 13-pin connector from the backup sensor harness into the junction box. Plug the junction box 13-pin connector into the backup sensor harness. RIGHT REAR SIDE TRIM JUNCTION BOX 13-PIN 13-PIN Y 13-PIN DRAIN HOSE Y 2004 American Honda Motor Co., Inc. - All Rights Reserved. AII (0409) 7 of 12

8 23. Route the backup sensor harness under the drain hose, and secure the backup sensor harness to the vehicle harness using two wire ties. 25. On the driver s side of the vehicle, attach the backup sensor harness ground terminal using the vehicle ground terminal. JUNCTION BOX 2A FUSE LABEL FUSE CASE POWER DOOR CONTROL UNIT (EX, and EX-L MODELS) GROUND TERMINAL DRAIN HOSE Y 24. Secure the backup sensor harness to the vehicle harness using five wire ties. GROUND Y 26. Install the 2A fuse label to the fuse case. 27. Secure the backup sensor harness to the vehicle harness using three wire ties. 28. Get the backup sensor control unit and the control unit bracket. Install the control unit bracket to the control unit. CONTROL UNIT Y CONTROL UNIT BRACKET Y 8 of 12 AII (0409) 2004 American Honda Motor Co., Inc. - All Rights Reserved.

9 29. Plug the backup sensor harness 10-pin connector into the control unit. Attach the control unit to the inside of the left rear vehicle panel using one 6 mm flange nut. 31. Plug the backup sensor harness 5-pin connector into the buzzer unit. Attach the backup sensor harness to the vehicle panel using two wire ties. CONTROL UNIT 10-PIN WITH CLIP 6 mm FLANGE NUT POWER DOOR CONTROL UNIT (EX, and EX-L MODELS) Y 5-PIN 32. Install the two wire ties of the harness to the vehicle panel Y 30. Secure the backup sensor to the vehicle harness using one wire tie. CUSHION TAPE (Half of cushion tape from step 16) 3-PIN WITH CLIP POWER DOOR Y CONTROL UNIT (EX, and EX-L MODELS) Y 33. Using the remaining half of the cushion tape, secure the backup sensor harness to the vehicles panel American Honda Motor Co., Inc. - All Rights Reserved. AII (0409) 9 of 12

10 34. Using the isopropyl alcohol, clean the areas where the cable clips will attach. On the outside of the vehicle, route the backup sensor harness across the back of the vehicle. Secure the backup sensor harness to the vehicle panel and to the bumper beam with two cable clips and two small wire ties. 36. Remove the bumper beam support. BEAM SUPPORT LONG BEAM GREEN TAPE EPT SEALERS (3) 2-PIN S Y SMALL S (2) CABLE CLIPS (2) GREEN TAPE 35. Using scissors, cut two EPT sealers in half. Attach one cut EPT sealer at each green tape location on the backup sensor harness Y 37. Route the backup sensor harness along the bumper beam. Secure the backup sensor harness to the bumper beam using three long wire ties. 38. Reinstall the bumper beam support. Installing the Switch 39. On the inside of the left rear pillar trim, measure and mark the pillar trim at the measurements shown. Measure from the base of the ribs. While wearing eye protection, drill a 26 mm hole at the marked position. EPT SEALER (Cut in half.) 24 mm PILLAR TRIM EPT SEALERS (3) 18 mm GREEN TAPE GREEN TAPE GREEN TAPE Y 26 mm HOLE SAW Y 10 of 12 AII (0409) 2004 American Honda Motor Co., Inc. - All Rights Reserved.

11 40. Install the switch into the hole in the left rear pillar trim in the direction shown. PILLAR TRIM UP DOWN SWITCH Installing the Backup Sensors 42. On the inside of the rear bumper, locate the four scribe marks. Using a pushpin, mark the bumper at each of the four locations. When you mark the bumper with a pushpin, be careful not to pierce through the other marks. MARK FOR (Mark in the same position of the other side.) MARK NOT USED (Do not pierce through these marks.) PUSHPIN 22 mm HOLE SAW SWITCH REAR 26 mm HOLE Y 41. Plug the backup sensor harness 3-pin connector into the switch, and reinstall the left rear pillar trim. 3-PIN PILLAR TRIM SWITCH 26 mm HOLE SAW PUSHPIN MARK FOR (Mark in the same position of the other side.) Y MARK NOT USED (Do not pierce through the mark.) 43. While wearing eye protection, drill a 22 mm hole through the outboard marks, and drill a 26 mm hole through the two inboard marks. Remove any burrs Y 2004 American Honda Motor Co., Inc. - All Rights Reserved. AII (0409) 11 of 12

12 44. Install the two corner sensors and the two center sensors into the rear bumper with the arrow on the sensors facing up. Do not to push the microphone when installing sensors. REAR HOUSING MICROPHONE SPACER UP DOWN CORNER CENTER CORNER Y 47. Check that all wire harnesses are routed properly, and that all connectors are plugged in. 48. Reinstall all removed parts. 49. Reconnect the negative cable to the battery. 50. Enter the customer s radio anti-theft code, and reset the radio station presets. 51. Reset the clock. 52. Check the operation of the backup sensors as described in the backup sensor owner s manual supplied. NOTE: Whenever the battery is disconnected, the driver s AUTO function is disabled. 53. Start the engine. Push down on the driver's window switch until the window is fully open, then hold the switch for 2 seconds or more. 54. Pull up on the driver s window switch to close the window completely. 55. Test the driver s AUTO window function. 45. On the inside of the bumper, install the two spacers on the center sensors. 46. With the help of an assistant, connect the 2-pin connectors from the backup sensor harness to the sensors, then reinstall the bumper. 2-PIN CORNER 2-PIN 2-PIN CORNER 2-PIN REAR CENTER 2-PIN Y 12 of 12 AII (0409) 2004 American Honda Motor Co., Inc. - All Rights Reserved.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory S Application 2010 ODYSSEY Publications No. AII 41818 Issue Date JUNE 2009 PARTS LIST Right center sensor clip (Black) Backup Sensor Attachment Kit P/N 08V67-SHJ-101C