- PDF Free Download

Size: px

Start display at page:

Download ""

Brenda Eleanore Haynes
6 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII S 2007 ODYSSEY Issue Date JULY 2006 PARTS LIST Short sub harness (LX model) Right fog light Long sub harness (EX model and Touring model) Left fog light Relay bracket Right bracket Left bracket Relay (Gray) Relay (Black) Fog light harness Switch harness 26 Wire ties Template Wire tie with holder 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 08V31-SHJ of 19

2 3 Wire ties with clip Fuse label (LX model only) 4 Small wire ties 10A Fuse Switch 2 Washer-bolts, 6 x 16 mm 2 Washer-bolts, 5 x 16 mm 6 Self-tapping screws Ground bolt TOOL AND SUPPLIES REQUIRED Phillips screwdriver Stubby #2 Phillips screwdriver 10 mm Socket Ratchet Diagonal cutters 10 mm Combination wrench Drill 3 mm, 6 mm, 7 mm, 10 mm, Drill bit Eye protection (face shield, safety goggles, etc.) Hacksaw blade File Masking tape Flat-tip screwdriver Felt-tip pen Pushpin Blanket Isopropyl alcohol Shop towel Scissors INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: Be careful not to damage the body finish. 4 Cushion tapes Take care not to damage the clips and tabs. 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 2 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

3 3. Remove the radiator cover (ten clips). Cutting the Front Bumper CLIPS (10) 5. To protect the bumper, apply masking tape to the front side of the bumper around the right and left fog light opening. MASKING TAPE RADIATOR COVER Y OPENING BUMPER Y 4. Remove the front bumper. On each side, pull the inner fender back, and remove the two self-tapping screws. Remove the eight clips. Remove the two bolts, and remove the front bumper. Place the front bumper on a blanket. 6. On the inside of the bumper, align the template with the left fog light mounting position. Using a pushpin, mark the bumper at each of the six locations on the template. Ignore the pre-scribed line. INSIDE THE BUMPER PUSHPIN TEMPLATE TEMPLATE SELF- TAPPING SCREWS (2) CLIPS (8) BUMPER S (2) Y PUSHPIN Y INSIDE THE BUMPER 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 3 of 19

4 7. Using a felt-tip pen, mark the bumper in the area shown. NOTE: If there are pre-scribed lines on the bumper, ignore the pre-scribed lines, and use the template as the guide. BUMPER FELT-TIP PEN 10. On the outside of the front bumper, use a hacksaw blade to cut the bumper at the fog light opening along the three sides. OPENING HACKSAW BLADE MARK TEMPLATE Y BUMPER Y 8. Turn the template over, and mark the other side of the bumper the same way. 9. While wearing eye protection, drill one 7 mm hole and four 10 mm holes at the marked locations. Start with a 3 mm drill bit, and finish with a 7 mm or a 10 mm drill bit. 11. On the inside of the front bumper, cut out the fog light opening from the front bumper using a hacksaw blade. Remove any burrs, and remove the masking tape. INSIDE THE BUMPER DRILL (Drill with 3 mm drill bit, finish with a 10 mm drill bit.) 7 mm HOLE 10 mm HOLES (4) OPENING PUSHPIN MARK DRILL (Drill with 3 mm drill bit, finish with a 10 mm drill bit.) INSIDE THE BUMPER Y CUT LINE Y 4 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

5 Installing the Fog Lights 12. Install the left bracket to the front bumper using three self-tapping screws. Routing the Fog Light Harness 16. Open the hood. Remove the FI-ECU cover (two clips). BUMPER FI-ECU COVER CLIP Insert SELF- TAPPING SCREW LEFT BRACKET Y FI-ECU 13. Insert the fog light through the opening in the front bumper and into the bracket. 14. Install the fog light to the bracket using one 5 x 16 mm washer bolt Y 17. Remove the two under-hood fuse/relay box bolts, and slide the fuse/relay box to the side. LEFT BRACKET LEFT RETAINING TABS (4) UNDER-HOOD FUSE/RELAY BOX COVER 5 x 16 mm WASHER Y 15. Repeat steps 9 through 14 to cut the bumper, and install the right fog light. UNDER- HOOD FUSE/ RELAY BOX Y 18. Remove the under-hood fuse/relay box cover (four retaining tabs) American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 5 of 19

6 19. Remove the under-hood fuse/relay box lower cover from the under-hood fuse/relay box (six retaining tabs). 22. Remove the subfuse box from the vehicle bracket. RELEASE CLIP To remove fuse relay box. UNDER-HOOD FUSE/RELAY BOX SUBFUSE BOX UNDER-HOOD FUSE RELAY BOX LOWER COVER TAB CASE SUBFUSE BOX RETAINING TABS (6) Y If the vehicle you are working on is an LX model, go to step 28; otherwise, continue with step Locate the subfuse box near the under-hood fuse relay box. Remove the subfuse box cover (two tabs). SUBFUSE BOX COVER TAB SCREW UNDER-HOOD FUSE RELAY BOX BRACKET Y 23. Remove the subfuse box from the case (one tab). 24. Get the long subharness. Plug the 1-pin terminal on the long subharness into the rear of the subfuse box at the location shown. (Rear view) SUBFUSE BOX SUBFUSE BOX UNDER-HOOD FUSE RELAY BOX Y 21. Remove the screw, and disconnect the vehicle harness. LONG SUB SUBFUSE BOX Y 6 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

7 25. Secure the long subharness to the subfuse box harness with one small wire tie. 29. Get the short subharness. Plug the 1-pin terminal from the short subharness into the back of the vehicle 20-pin connector. SMALL SUBFUSE BOX SHORT SUB 1-PIN LOCATION 20-PIN Release lock tabs to insert pin. (View from the harness side) SHORT SUB 1-PIN TERMINAL LONG SUB UNDER-HOOD FUSE/RELAY BOX 26. Secure the long subharness to the vehicle harness with one wire tie. 27. Reinstall the subfuse box Y If the vehicle you are working on is an EX or Touring model, go to step 31; otherwise, continue with step Disconnect the vehicle 20-pin connector from the bottom of the under-hood fuse relay box. 20-PIN SUB UNDER- HOOD FUSE RELAY BOX Y 30. Reconnect the vehicle 20-pin connector into the under-hood fuse/relay box. 31. Disconnect the vehicle 18-pin connector from the back of the under-hood fuse/relay box. BOTTOM OF THE UNDER- HOOD FUSE/ RELAY BOX BACK OF THE UNDER-HOOD FUSE/RELAY BOX 20-PIN 18-PIN Y Y 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 7 of 19

8 32. Get the fog light harness. Plug the 1-pin white/ green and the 1-pin red/green terminals into the back of the 18-pin connector in the locations shown. 36. Below the under-hood fuse relay box, secure the fog light harness connector to the vehicle harness using the wire tie with holder, and trim the wire tie. Release lock tabs to install pins Red/ Green White/ Green Red/Green WITH HOLDER View from the harness side 18-PIN White/Green UNDER- HOOD FUSE/ RELAY BOX Y 18-PIN Y 37. Using isopropyl alcohol, thoroughly clean the areas where the cushion tape will attach. Using scissors, cut one cushion tape in half, and attach one half to the FI-ECU in the area shown. 33. Reconnect the vehicle 18-pin connector into the under-hood fuse relay box. 34. Plug the connector on the long/short subharness into the fog light harness connector. Secure the fog light harness and the subharness to the vehicle harness with one small wire tie, then trim the wire tie. SHORT SUB (LX model) FI-ECU 1/2 CUSHION TAPE FI-ECU CUSHION TAPE (half) SMALL LONG SUB (EX/Touring model) 35. Reinstall the under-hood fuse relay box lower cover in the original position Y Remove the tape. 2-PIN 2-PIN 38. Locate the vehicle 2-pin connector blue taped to the vehicle harness, and remove the blue tape to free the connector. Plug the fog light harness 2-pin connector into the vehicle harness 2-pin connector. 39. Secure the fog light harness connector to the vehicle harness using one wire tie. 8 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

9 40. Route the fog light harness forward along the vehicle harness. Loosely secure it to the vehicle harness with two wire ties. 42. Attach the two wire ties with clips on the fog light harness into the holes in the vehicle body. RIGHT HEADLIGHT CUSHION TAPE WITH CLIP (2) LOOSELY SECURE WITH WASHER TANK FRAME Y Y 43. Using isopropyl alcohol, thoroughly clean the areas where the cushion tape will attach. Secure the fog light harness to the vehicle s frame with the cushion tape. 41. Route the right fog light harness 2-pin connector along the vehicle harness and into the bumper area. 44. Adjust the fog light harness until the green tape on the fog light harness is close to the wire tie with clip on the vehicle harness. Secure the fog light harness to the vehicle harness with two wire ties. WIRE TIE HORN Y GREEN TAPE WIRE TIE WIRE TIE WITH CLIP Y 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 9 of 19

10 45. Tighten the two wire ties installed in step Route the fog light harness along the vehicle harness. Attach the fog light harness to the vehicle harness with two wire ties. WIRE TIE Y 46. Reinstall the under-hood fuse/relay box. 47. Remove the power steering reservoir from the vehicle bracket Y 49. Route the fog light harness along the vehicle harness on the bulkhead, and loosely attach the fog light harness to the vehicle harness with four wire ties. BRACKET POWER STEERING RESERVOIR BULKHEAD (Attach loosely.) Y Y 10 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

11 50. Route the fog light harness behind the battery, and loosely secure it to the vehicle harness with three additional wire ties. 53. Route the fog light harness as shown. (Attach loosely.) BATTERY Y 51. Locate the wire tie with clip near the end of the fog light harness. Wrap a cushion tape around the fog light harness at the measurement shown. 54. EX model with AUTO air: Secure the fog light harness to the sensor harness with three wire ties. WITH CLIP CUSHION TAPE SENSOR 120 mm BRACKET BODY PANEL (Discard) GROUND GROUND TERMINAL WIRE TIE Y WIRE TIE WITH CLIP Y 55. EX model with AUTO air: Remove the bolt from the vehicle bracket. Secure the ground terminal from the fog light harness to the vehicle bracket using the ground bolt supplied. 52. Attach the wire tie with clip on the fog light harness into the hole in the body panel American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 11 of 19

12 56. LX Model: Route the fog light harness as shown and secure it with three wire ties with clips to the vehicle frame. 60. Get the relay bracket and the two relays. Attach the relays to the relay bracket with two 6 x 16 mm washer bolts. WITH CLIPS RELAY BRACKET GREEN TAPE FRAME WITH CLIP 6 x 16 mm WASHER- RELAY (BLACK) Y GROUND GROUND TERMINAL Y RELAY (GRAY) 57. LX Model: Use the ground bolt to secure the ground terminal on the fog light harness to the vehicle frame. 61. Plug the blue fog light harness 4-pin connector into the gray relay. Plug the brown fog light harness 4-pin connector into the black relay. RELAY (BLACK) RELAY (GRAY) 58. Using isopropyl alcohol, thoroughly clean the area where the cushion tape will attach. Secure the fog light harness to the vehicle frame with one cushion tape. CUSHION TAPE FRAME 4-PIN (BROWN) 4-PIN (BLUE) Y Y 59. Tighten the seven wire ties installed in steps 49 and of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

13 62. Loosen the bolt that secures the existing relay box, and slide the tab from the fog light relay bracket under the bolt. Retighten the relay bracket bolt. RELAY 64. With the help of an assistant, plug the fog light harness 2-pin connectors into the fog light connectors, and reinstall the front bumper in its original position. Be careful that the fog light harness does not get caught between the bumper and the splash shield. 2-PIN EXISTING RELAY BOX FRAME 63. Secure the fog light harness to the vehicle harness with three wire ties Y BUMPER 2-PIN Y Installing the Fog Light Switch 65. Remove the instrument side panel (six clips, three retaining tabs). CLIPS (6) RETAINING TAB Y INSTRUMENT SIDE PANEL INSTRUMENT SIDE PANEL SHOP TOWEL FLAT-TIP SCREWDRIVER B 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 13 of 19

14 66. Reaching through the opening in the dashboard, release the four clips and pull out on the switch panel. If equipped, disconnect the vehicle connectors from the switch panel, and remove the switch panel. 68. Remove the VSA switch. (two retaining tabs). EX Model Shown CLIPS (4) EX Model Shown 6-PIN VSA SWITCH Y SWITCH PANEL 67. Remove the switch lid (two retaining tabs) Y 69. Unplug the vehicle 6-pin connector from the VSA switch. 70. Route the switch harness 5-pin connector through the switch hole and plug it into the fog light switch. 71. Install the fog light switch into the hole where you removed the switch lid. EX Model Shown SWITCH 6-PIN 6-PIN (VSA) SWITCH 5-PIN RETAINING TABS SWITCH LID Y FOG LIGHT SWITCH SWITCH 6-PIN VSA SWITCH Y 72. Route the 6-pin switch harness connector through the switch hole and plug it into the VSA switch. Plug the vehicle 6-pin VSA connector into the switch harness. 14 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

15 73. Route and fold the switch harness back along the vehicle harness, and secure the switch harness to the vehicle harness with two wire ties. 75. At the fuse box, secure the switch harness to the vehicle harness with three wire ties. SWITCH Y SWITCH Y 74. Locate the 2-pin connector at the front of the fuse box that is black-taped to the vehicle harness near the front bulkhead. Remove the black tape to free the connector. Plug the 2-pin connector from the switch harness into the vehicle harness 2-pin connector you just freed. 76. Install the 10A fog light fuse. EX/Touring Model: Install the 10A fuse into the subfuse box in the location shown. TOP VIEW SWITCH 2-PIN 10A FUSE FUSE LOCATION BLACK TAPE 2-PIN SUB FUSE BOX Y Y 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 15 of 19

16 LX Model: Install the 10A fuse into the underhood fuse/relay box in the location shown. FUSE LOCATION TOP VIEW 10A FUSE 78. Check that all wire harnesses are routed properly, and all connectors are plugged in. 79. Reinstall all removed parts. 80. Reconnect the negative cable to the battery. 81. Enter the customer s radio anti-theft code, and reset the station presets. 82. Reset the clock. NOTE: Whenever the battery is disconnected, the driver s AUTO window function is disabled. 83. Start the engine. Push down on the driver s window switch until the window is fully open, then hold the switch for 2 seconds or more. 84. Pull up on the driver s window switch to close the window completely, then hold the switch for 2 seconds or more. 85. Test the AUTO window function. UNDER-HOOD FUSE RELAY BOX Y 77. LX Model Only: Attach the 10A fuse label to the inside of the under-hood fuse relay box. FUSE LABEL Y UNDER-HOOD FUSE RELAY BOX 16 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

17 Fog Light Aiming Adjustment 86. Remove the bolt and clip, and pull down the inner fender. CLIP Pull down. 87. Adjust the fog lights. INNER FENDER Y Adjust the aiming according to local laws and regulations. To adjust, turn the adjustment screw in or out until the correct aiming is obtained. USE AND CARE How to Operate Fog Lights Turn the light switch to the on position (headlights on low beam ). Press the fog light switch (indicator is on). If the fog lights don t come on, check the fuse and all the connectors, including the ground cable and the fusible link. NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. Replacing the Bulb NOTE: Use only a Honda Genuine Halogen Light Bulb of specified wattage. BULB, (H8) P/N S5A-J010-M1 Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a clean, soft cloth that has been dampened with denatured alcohol or a mild detergent solution. ADJUSTING SCREW TO RAISE TO LOWER Y 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 17 of 19

18 1. Remove the bolt and clip, and pull down the inner fender. 4. Unplug the connector from the bulb, and remove the bulb from the fog light. CLIP Pull down. BULB 2. Unplug the connector from the fog light. INNER FENDER Y Y 5. Install the new bulb into the fog light. Align the tab on the fog light with the cutout in the bulb socket when installing the new bulb. If not aligned, there is possibility that the fog light may annoy oncoming drivers. SCREW Y BULB 3. Remove the screw that fastens the fog light, and pull the light out toward you Y 6. Reinstall the removed parts in the reverse order of removal: Check that the wire harnesses are not pinched. Be sure to tighten the self-tapping screw and bolts securely. 7. Check the operation of the fog light; adjust the aiming if necessary. 18 of 19 AII (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.

19 CIRCUIT DIAGRAM Under-hood Relay Box HOT WITH HEADLIGHT SWITCH IN SWITCH HEAD AND IN DIMMER HAED,AND SWITCH IN HIGHBEAM DIMMER POSITION SWITCH IN HIGHT WHT/GRN FR HOT WITH HEADLIGHT WITH HEADLIGHT SWITCH IN HEAD IN HAED HOT AT ALL TIMES Fog Light Fuse 10A LX Model RED/GRN BLU/RED HOT WITH HEADLIGHT SWITCH IN PARK OR HEAD Relay HOT AT ALL TIMES Sub Fuse Box Fog Light Fuse 10A RED/BLK 2 BLU 1 Switch 1=Indicato INDICATOR 2=Switch Illumination EX Model/ Touring RED Illumination Control GRN BLK Relay BLU/YEL Front Fog Light BLK BLK BLK BLK BLK BLACK BRN BROWN LIGHT SWITCH YEL YELLOW ORN ORANGE BLU BLUE PUR PURPLE OFF Low Hi GRN GREEN NAT NATURAL SWITCH OFF ON ON - RED RED PNK PINK WHT WHITE GRY GRAY LT BLU LIGHT BLUE LT GRN LIGHT GREEN Y 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0607) 19 of 19

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08V31-SHJ-100A 2010 ODYSSEY AII 41829-43750 Issue Date MARCH 2010 PARTS LIST Relay Left fog light 22 Wire ties Right fog light Wire