EXPERIMENTAL AND COMPUTATIONAL EVALUATION OF EMISSIONS OF AN ENGINE WITH A RE-ENTRANT PISTON BOWL - A VALIDATION
|
|
- Georgiana Cobb
- 5 years ago
- Views:
Transcription
1 International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 6, June 2017, pp , Article ID: IJMET_08_06_041 Available online at ISSN Print: and ISSN Online: IAEME Publication Scopus Indexed EXPERIMENTAL AND COMPUTATIONAL EVALUATION OF EMISSIONS OF AN ENGINE WITH A RE-ENTRANT PISTON BOWL - A VALIDATION M. Thamarai Kannan, Rupesh P L, Raja K and M.P. Siva Assistant Professor, Department of Mechanical Engineering, Veltech Dr. RR & Dr.SR University, Avadi, Chennai, Tamilnadu, India ABSTRACT Reductions in fuel consumption and pollutant emissions from direct injection diesel engines are important issues in engine research. To achieve these reductions, rapid and better fuel air mixing is the most important requirement, the design of the piston bowl and the nozzle configuration perform a defining role. The shape of the combustion chamber can also help to form better mixtures. The change in shape of the combustion chamber leads to different changes in measurements of pip region, bowl lip area, and toroidal radius etc. and this makes high cost for manufacturing. The selection of an optimised shape of combustion chamber from the manufacturing of different shapes and experimental observation of those shapes may lead to high cost. The aim of this study focuses on the validation of the experimental results with that of the computational using an engine with re-entrant piston bowl. The computational results hold in agreement with experimental results which leads to the future scope of simulation of different piston bowl configurations using the computational model in order to choose an optimised combustion chamber of an existing diesel engine in order to meet CPCB-II emission Norms. Key words: Direct Injection Diesel Engine, Piston bowl, Re-entrant type, Bowl radius, Emissions. Cite this Article: M. Thamarai Kannan, Rupesh P L, Raja K and M.P. Siva. Experimental and Computational Evaluation of Emissions of an Engine with a Re- Entrant Piston Bowl - A Validation. International Journal of Mechanical Engineering and Technology, 8(6), 2017, pp INTRODUCTION Environmental concerns have led to progressively more stringent emission regulations for diesel engines, and much research has addressed this issue. Incomplete combustion of the fuel is mainly responsible for the HC and PM emissions and better mixture formation would be the best way to improve the combustion and emission quality. Especially in small DI diesel engines a major part of the injected fuel impinges on the cavity (combustion chamber) walls editor@iaeme.com
2 Experimental and Computational Evaluation of Emissions of an Engine with a Re-Entrant Piston Bowl - A Validation This causes the formation of a fuel film on the cavity wall when the wall temperature is low and forms rich mixtures near the cavity wall when operating loads are high, giving a significant effect on unburnt HC and soot emissions. Compact high speed DI diesel engines are attractive power sources for modern passenger cars due to their low carbon dioxide emissions. However, these engines still emit objectionable PM and NOx at a time when emission regulations are becoming more stringent. Much research has attempted to reduce the PM emissions by injecting fuels at high pressure without increasing NOx emissions. In small DI diesel engines much of the spray reaches the cavity wall even when injected at high pressures. At low temperatures and at light loads a film of impinged fuel forms on the cavity wall. The fuel adhering to the wall is thought to be the major source of unburnt HC emissions. Pilot injection and retarded timings have been used to reduce NOx emissions and engine noise. Direct-injection (DI) diesel engines have served in both light-duty and heavy-duty vehicles because of the evident benefit of higher thermal efficiency than all other engines. However, due to the short period of fuel air mixing time, it is unfavorable to the combustion process. As the results, DI diesel engine emits more particulates and nitrogen oxides (NOx) than its counterparts. The methods of emission reduction from an engine include In-cylinder emission reduction techniques and after treatment techniques which is shown in Fig.1. Emission reduction techniques In-cylinder techniques After treatment devices 1.Combustion bowl shape optimization 2.Exhaust Gas Regeneration 3.Rate and timing of fuel injection 4.Compression ratio 1.Catalytic Converter 2.Diesel Particulate filter 3.Diesel oxidation catalyst 4.Selective catalytic reduction Figure 1 Emission reduction techniques To achieve a better combustion with less pollutant emissions in DI diesel engines, the method, which is widely used and proved effective, is accelerating the fuel air mixing to improve the combustion in cylinder and reduce the combustion period. The basic nomenclature of combustion bowl is as shown in the fig editor@iaeme.com
3 M. Thamarai Kannan, Rupesh P L, Raja K and M.P. Siva Figure 2 Basic nomenclature of a combustion bowl Katsuhiko Miyamoto et al [1] investigated the effects of tumble & squish in the context of in-cylinder flows on partial load fuel consumption for gasoline engines and also compared three piston cavities for heat release rate & incoming air flow along with the study on effects of variation of ignition timing & torque. Caroline L. Genzale et al studied the effects of variation of piston bowl geometry parameters for soot & NOx emission using computational investigation into the effects of spray targeting, bowl geometry and swirl ratio for low temperature combustion in a heavy duty diesel engine [2]. Ramchandra Divakar & Satbir singh prepared a simulation model for a DI diesel engine operating under Premixed charge Compression Ignition (PCCI) combustion model [3] in order to find out the importance of spray-bowl interaction in the engine and validated for experimental results. Effects of start of injection (SOI) and spray cone angle are studied on combustion & emission. Lu Lin et al [4] investigated the combustion shape effects on in cylinder air motion and performance of a DI diesel engine. The results show that, by optimizing the combustion chamber shape, the duration of high turbulence in cylinder is prolonged, and the diffuse combustion during the later period of combustion process is enhanced. Rahman M et al [5] found that a re-entrant type combustion chamber with round lip and round bottom corners provides better air and fuel distribution than a simple cylindrical combustion chamber. The results shows that the re-entrant cavity with round lip produces larger spray volumes, wider spray spreading, and better balance of fuel inside and outside the cavity than the simple cylindrical cavity. Rahman Md. et al [6] designed a new combustion chamber concept for small DI diesel engines. The spray formation and its distribution inside and outside the combustion chamber was investigated photographically in a small DI diesel engine with transparent cylinder and piston. The inferences drawn from the above literature survey shows that individual research has been carried out for experimental and computational tests. This shows that a validation of experimental results with that of computational is required. This provided the objective for the current work. After validation if the experimental results hold in good agreement with that of computational, we can able to optimize the piston bowl of an existing diesel engine using the current simulation model in order to meet CPCB-II emission Norms. The methodology of the research work has been categorized in 5 steps which is shown in a flow diagram depicted in Fig editor@iaeme.com
4 Experimental and Computational Evaluation of Emissions of an Engine with a Re-Entrant Piston Bowl - A Validation Detailed study of existing piston bowl. Experimental observation of emissions using test rig of a directinjection diesel engine with a re-entrant type piston bowl Modeling of piston bowl as per specifications of the experimental test rig Simulation of piston bowl geometry for emission behavior Validation of experimentaal results with computational Figure 4 Methodology of the research 2. EXPERIMENTAL SETUP Fig.5. (a) shows a CAD model of the engine designed in Pro-E used for simulation purpose. The engine used for experimental purpose is also shown in Fig.5. (b) (a) (b) Figure 5 (a) Engine- CAD Model; (b) Experimental Test rig- DI Engine The engine with the specifications shown in Table 1 is used for experimental test with the operating conditions shown in Table 2. Table 1 Engine Specifications Engine Parameters Specifications Displacement (cm 3 ) 1997 Number of cylinders 4 Number of valves 16 Engine breathing Turbo Bore x Stroke 85 x 88 mm Compression ratio 18:1 Max 4000rpm 66kW editor@iaeme.com
5 M. Thamarai Kannan, Rupesh P L, Raja K and M.P. Siva Parameters Table 2 Operating Conditions Desired Values Engine water circuit pressure 1.4 bar Engine speed 4000 rpm Water temperature control lower threshold 80 C Water temperature control higher threshold 85 C Water temperature alert threshold 95 C Water temperature alarm threshold 98 C Oil temperature alert threshold 85 C Oil temperature alarm threshold 98 C Oil pressure alert threshold 1 bar Oil pressure alarm threshold 0.8 bar 2.1. Emission Test and Measurements Emission test on constant speed diesel engine has been carried out at five different load conditions 10%, 25%, 50%, 75%, 100% respectively using transient dynamometer. Table 3 shows the performance measurement of the experimental test rig and the observed emission measurements is shown in Table 4. Table 3 Test Readings I Sl.No. Load (%) Torque (Nm) Power (kw) BMEP (bar) BSFC (g/kwh) Sl.No. Load (%) Weight factor Engine Speed (rpm) Table 4 Test Readings II CO emissions (g/hr) HC emissions (g/hr) NoX emissions (g/hr) PM (g/hr) Fig. 6 (a) & (b) shows the variation of CO and HC emissions along with change in load respectively in the form of plot. It has been observed that CO & HC emissions decrease with increase in load editor@iaeme.com
6 Experimental and Computational Evaluation of Emissions of an Engine with a Re-Entrant Piston Bowl - A Validation (a) (b) Figure 6 (a) Load (%) Vs CO emissions (g/hr); (b) Load (%) Vs HC emissions (g/hr) The variation of Particulate and NOx emissions along with load has been depicted in the form of graph which is shown in Fig. 7 (a) & (b) respectively. As the load increases, particulate and NOx emissions increases simultaneously which is observed in the graph. (a) (b) Figure 7 (a) Load (%) Vs NoX emissions (g/hr); (b) Load (%) Vs PM emissions (g/hr) Table 5 shows the results of emission test which indicated the rate of emission of No x, Co, HC & PM in g/kwhr. Emission Table 5 Emission results g/kwhr No x Co HC PM editor@iaeme.com
7 3. COMPUTATIONAL MODEL M. Thamarai Kannan, Rupesh P L, Raja K and M.P. Siva 3.1. Design of Piston Bowl The Fig 8 (a) & (b) shows the piston bowl in 2D and 3D model selected for the current work. The bowl specifications were shown in Table 6. Table 6 Bowl Specifications Bowl Throat Dia (mm) Bowl Radius (mm) Lip Radius (mm) Compression Ratio Base Bowl An engine model of closed surface geometry is created which is shown in below fig 9 for the CFD simulation work. This closed surface geometry is converted into STL file and then it is imported in the CFD software. While importing this surface geometry file into CFD software there may be loss of surface occur. Those surfaces can be repaired or reproduced in the CFD software (a) (b) Figure 8 Piston Bowl (a) 2D Model (b) 3D Model (a) (b) Figure 9 (a) Engine model for simulation; (b) Imported Engine model for simulation Model is prepared to simulate actual operating conditions of engine. Validation of model is done by comparing available engine measurements. The engine under simulation is used for power generation application. The engine runs at constant speed of 1500 rpm and hence the same is considered during simulation. Other important parameters to be used are swirl no. at inlet valve closure, injection duration, spray cone angle, EGR rate. Engine and spray data used for the simulation of computational model is shown in Table 7 (a) and (b) editor@iaeme.com
8 Experimental and Computational Evaluation of Emissions of an Engine with a Re-Entrant Piston Bowl - A Validation Table 7 (a) Engine Data Bore (mm) 85 Stroke (mm) 88 Compression Ratio Base Engine18 Connecting Rod Length 145 Engine Speed (rpm) 1500 EGR % 20 IVC and EVO crank angles 234 &478 Table 7 (b) Spray Data Fuel Type Diesel Start of Injection 10 deg BTDC Injection Duration 17 deg No of holes 5 Nozzle hole size (mm) 0.129mm Table 8 shows the comparison of engine test result with simulated result. Simulated results are within ± 5% except CO emissions. Table 8 Simulation readings Parameter Experimental Reading Predicted CPCB-I limits CO emissions(g/kwh) HC emissions(g/kwh) NoX emissions(g/kwh) VALIDATION OF COMPUTATIONAL RESULTS WITH EXPERIMENTAL editor@iaeme.com
9 M. Thamarai Kannan, Rupesh P L, Raja K and M.P. Siva Figure 10 (a) Load (%) Vs CO emissions (g/hr); (b) Load (%) Vs HC emissions (g/hr); (c) Load (%) Vs NoX emissions (g/hr) The results of simulation of the computational model are compared with those of experimental which are depicted as graphs indicating the load variation with CO, HC and No x emissions. Fig. 10 (a), (b) & (c) shows the variation of both experimental and simulation and it indicates that both hold in good agreement with each other. 5. CONCLUSIONS In this work CONVERGE CFD software is used to optimize the piston bowl for constant speed power generation direct injection diesel engine. The model was first validated with available engine measurements and used to predict emissions. It has been concluded after validation that the experimental results hold in good agreement with that of computational and we can able to optimize the piston bowl of an existing diesel engine using the current simulation model in order to meet CPCB-II emission Norms. The present study also reveals the role of combustion bowl shape and nozzle geometry on emissions of a DI Diesel Engine. REFERENCES [1] Katsuhiko, Miyamoto et al Enhancement of Combustion by Means of Squish piston, Technical Series 2006 No. 18. [2] Genzale, C., Reitz, R., and Wickman, D., A Computational Investigation into the Effects of Spray Targeting, Bowl Geometry and Swirl Ratio for Low- Temperature Combustion in a Heavy-Duty Diesel Engine, SAE Technical Paper , 2007, doi: / [3] Diwakar, R. and Singh, S., Importance of Spray-Bowl Interaction in a DI Diesel Engine Operating under PCCI Combustion Mode, SAE Technical Paper , 2009, doi: / [4] Lu Lin, Duan Shulin, Xiao Jin, Wu Jinxiang and Gao Xiaohong, Effects of Combustion Chamber Geometry on In-Cylinder Air Motion and Performance in DI Diesel Engine, SAE Technical Paper Series [5] Rahman M. Montajir, H. Tsunemoto H. Ishitani and T. Minami, Fuel Spray Behavior in a Small DI Diesel Engine: Effect of Combustion Chamber Geometry, SAE Technical Paper Series editor@iaeme.com
10 Experimental and Computational Evaluation of Emissions of an Engine with a Re-Entrant Piston Bowl - A Validation [6] Rahman Md. Montajir, Hideyuki Tsunemoto, Hiromi Ishitani, Tsukamoto Koji and Kubo Kenichi, A New Combustion Chamber Concept for Low Emissions in Small DI Diesel Engines SAE Technical Paper Series [7] Shubham Sawant and Deep Prajapati. A Review on Zero Emissions Vehicles. International Journal of Mechanical Engineering and Technology, 8(2), 2017, pp [8] Min-Seok Oh and Seunguk Na. Building Information Modelling (BIM) Based Co2 Emissions Assessment in the Early Design Stage. International Journal of Civil Engineering and Technology, 8(5), 2017, pp [9] C. Ajay Sekar, Combustion Study and Emission Characteristics of Blends of Diesel and Hythane for Gas Turbine Engines. International Journal of Mechanical Engineering and Technology, 7(6), 2016, pp editor@iaeme.com
EXPERIMENTAL INVESTIGATIONS ON 4- STROKE SINGLE CYLINDER DIESEL ENGINE (C.I) WITH CHANGING GEOMETRY OF PISTON
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 13, December 218, pp. 693 7, Article ID: IJMET_9_13_72 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=13
More informationEffect of Tangential Grooves on Piston Crown Of D.I. Diesel Engine with Retarded Injection Timing
International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn : 2278-800X, www.ijerd.com Volume 5, Issue 10 (January 2013), PP. 01-06 Effect of Tangential Grooves on Piston Crown
More informationNumerically Analysing the Effect of EGR on Emissions of DI Diesel Engine Having Toroidal Combustion Chamber Geometry
Numerically Analysing the Effect of EGR on Emissions of DI Diesel Engine Having Toroidal Combustion Chamber Geometry Jibin Alex 1, Biju Cherian Abraham 2 1 Student, Dept. of Mechanical Engineering, M A
More informationChandra Prasad B S, Sunil S and Suresha V Asst. Professor, Dept of Mechanical Engineering, SVCE, Bengaluru
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 7, July 2018, pp. 997 1004, Article ID: IJMET_09_07_106 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=7
More informationA STUDY ON DIESEL ENGINE PERFORMANCE DEPENDS ON BP AND BSFC BY APPLYING DIFFERENT INJECTION PRESSURE
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 11, November 2018, pp. 599 603, Article ID: IJMET_09_11_059 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=11
More informationA SIMULATION STUDY OF AIR FLOW IN DIFFERENT TYPES OF COMBUSTION CHAMBERS FOR A SINGLE CYLINDER DIESEL ENGINE
S1145 A SIMULATION STUDY OF AIR FLOW IN DIFFERENT TYPES OF COMBUSTION CHAMBERS FOR A SINGLE CYLINDER DIESEL ENGINE by Premnath SUNDARAMOORTHY a*, Devaradjane GOBALAKICHENIN b, Kathirvelu BASKAR c, and
More informationREDUCTION OF EMISSIONS BY ENHANCING AIR SWIRL IN A DIESEL ENGINE WITH GROOVED CYLINDER HEAD
REDUCTION OF EMISSIONS BY ENHANCING AIR SWIRL IN A DIESEL ENGINE WITH GROOVED CYLINDER HEAD Dr.S.L.V. Prasad 1, Prof.V.Pandurangadu 2, Dr.P.Manoj Kumar 3, Dr G. Naga Malleshwara Rao 4 Dept.of Mechanical
More informationNUMERICAL INVESTIGATION OF EFFECT OF EXHAUST GAS RECIRCULATION ON COMPRESSIONIGNITION ENGINE EMISSIONS
ISSN (Online) : 2319-8753 ISSN (Print) : 2347-6710 International Journal of Innovative Research in Science, Engineering and Technology An ISO 3297: 2007 Certified Organization, Volume 2, Special Issue
More informationEFFECT OF INJECTION ORIENTATION ON EXHAUST EMISSIONS IN A DI DIESEL ENGINE: THROUGH CFD SIMULATION
EFFECT OF INJECTION ORIENTATION ON EXHAUST EMISSIONS IN A DI DIESEL ENGINE: THROUGH CFD SIMULATION *P. Manoj Kumar 1, V. Pandurangadu 2, V.V. Pratibha Bharathi 3 and V.V. Naga Deepthi 4 1 Department of
More informationANALYSIS OF EXHAUST GAS RECIRCULATION (EGR) SYSTEM
ANALYSIS OF EXHAUST GAS RECIRCULATION (EGR) SYSTEM,, ABSTRACT Exhaust gas recirculation (EGR) is a way to control in-cylinder NOx and carbon production and is used on most modern high-speed direct injection
More informationExperimental Investigation on Diesel Engines by Swirl Induction with Different Manifolds
Research Article International Journal of Current Engineering and Technology E-ISSN 2277 416, P-ISSN 2347-5161 214 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Experimental
More informationEngine Conversion to CRDI Technology & Its Application Strategy
Engine Conversion to CRDI Technology & Its Application Strategy S Karthik 1, K Sairahul 1, N Logesh 1, K.Guru Prasad 1, D.Gopinath 2 U.G Student, Velammal Engineering College, Chennai, Tamilnadu, India
More informationComparison of Velocity Vector Components in a Di Diesel Engine: Analysis through Cfd Simulation
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X PP. 55-60 www.iosrjournals.org Comparison of Velocity Vector Components in a Di Diesel Engine: Analysis
More informationEFFECT ON PERFORMANCE AND COMBUSTION CHARACTERISTICS OF DIESEL ENGINE ENRICHED WITH HYDROGEN WITH VARIED PISTON BOWL GEOMETRY
International Journal of Mechanical Engineering and Technology (IJMET) Volume 6, Issue 10, Oct 2015, pp. 39-47, Article ID: IJMET_06_10_005 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=6&itype=10
More informationINFLUENCE OF THE NUMBER OF NOZZLE HOLES ON THE UNBURNED FUEL IN DIESEL ENGINE
INFLUENCE OF THE NUMBER OF NOZZLE HOLES ON THE UNBURNED FUEL IN DIESEL ENGINE 1. UNIVERSITY OF RUSE, 8, STUDENTSKA STR., 7017 RUSE, BULGARIA 1. Simeon ILIEV ABSTRACT: The objective of this paper is to
More informationPERFORMANCE AND EMISSION ANALYSIS OF DIESEL ENGINE BY INJECTING DIETHYL ETHER WITH AND WITHOUT EGR USING DPF
PERFORMANCE AND EMISSION ANALYSIS OF DIESEL ENGINE BY INJECTING DIETHYL ETHER WITH AND WITHOUT EGR USING DPF PROJECT REFERENCE NO. : 37S1036 COLLEGE BRANCH GUIDES : KS INSTITUTE OF TECHNOLOGY, BANGALORE
More informationStudy of Performance and Emission Characteristics of a Two Stroke Si Engine Operated with Gasoline Manifold Injectionand Carburetion
Indian Journal of Science and Technology, Vol 9(37), DOI: 10.17485/ijst/2016/v9i37/101984, October 2016 ISSN (Print) : 0974-6846 ISSN (Online) : 0974-5645 Study of Performance and Emission Characteristics
More informationCHAPTER 8 EFFECTS OF COMBUSTION CHAMBER GEOMETRIES
112 CHAPTER 8 EFFECTS OF COMBUSTION CHAMBER GEOMETRIES 8.1 INTRODUCTION Energy conservation and emissions have become of increasing concern over the past few decades. More stringent emission laws along
More informationConversion of Naturally Aspirated Genset Engine to Meet III A Norms for Tractor Application by Using Turbocharger
Conversion of Naturally Aspirated Genset Engine to Meet III A Norms for Tractor Application by Using Turbocharger M. Karthik Ganesh, B. Arun kumar Simpson co ltd., Chennai, India ABSTRACT: The small power
More informationPrediction on Increasing the Efficiency of Single Cylinder DI Diesel Engine Using EGR System
International OPEN ACCESS Journal Of Modern Engineering Research (IJMER) Prediction on Increasing the Efficiency of Single Cylinder DI Diesel Engine Using EGR System P.Muni Raja Chandra 1, Ayaz Ahmed 2,
More informationDigital Shaping and Optimization of Fuel Injection Pattern for a Common Rail Automotive Diesel Engine through Numerical Simulation
Digital Shaping and Optimization of Fuel Injection Pattern for a Common Rail Automotive Diesel Engine through Numerical Simulation European GT Conference 2017 - Frankfurt am Main Politecnico di Torino:
More informationINVESTIGATIONS OF EFFECTS OF PILOT INJECTION WITH CHANGE IN LEVEL OF COMPRESSION RATIO IN A COMMON RAIL DIESEL ENGINE
THERMAL SCIENCE: Year 2012, Vol. 17, No. 1, pp. 71-80 71 INVESTIGATIONS OF EFFECTS OF PILOT INJECTION WITH CHANGE IN LEVEL OF COMPRESSION RATIO IN A COMMON RAIL DIESEL ENGINE by Nilesh GAJARLAWAR a, Ajaykumar
More informationINTERNATIONAL JOURNAL OF ADVANCED RESEARCH IN ENGINEERING AND TECHNOLOGY (IJARET)
INTERNATIONAL JOURNAL OF ADVANCED RESEARCH IN ENGINEERING AND TECHNOLOGY (IJARET) International Journal of Advanced Research in Engineering and Technology (IJARET), ISSN ISSN 0976-6480 (Print) ISSN 0976-6499
More informationImproving Fuel Efficiency with Fuel-Reactivity-Controlled Combustion
ERC Symposium 2009 1 Improving Fuel Efficiency with Fuel-Reactivity-Controlled Combustion Rolf D. Reitz, Reed Hanson, Derek Splitter, Sage Kokjohn Engine Research Center University of Wisconsin-Madison
More informationCHAPTER 1 INTRODUCTION
1 CHAPTER 1 INTRODUCTION 1.1 GENERAL Diesel engines are the primary power source of vehicles used in heavy duty applications. The heavy duty engine includes buses, large trucks, and off-highway construction
More informationModule7:Advanced Combustion Systems and Alternative Powerplants Lecture 32:Stratified Charge Engines
ADVANCED COMBUSTION SYSTEMS AND ALTERNATIVE POWERPLANTS The Lecture Contains: DIRECT INJECTION STRATIFIED CHARGE (DISC) ENGINES Historical Overview Potential Advantages of DISC Engines DISC Engine Combustion
More informationParvezalam Shaikh and S.P. Yeole Department of Mechanical Engineering, P.R Pote (Patil) Group of Educational Institutions, Amravati, India
International Journal of Mechanical Engineering and Technology (IJMET) Volume 6, Issue 11, Nov 215, pp. 132-144, Article ID: IJMET_6_11_16 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=6&itype=11
More informationSmoke Reduction Methods Using Shallow-Dish Combustion Chamber in an HSDI Common-Rail Diesel Engine
Special Issue Challenges in Realizing Clean High-Performance Diesel Engines 17 Research Report Smoke Reduction Methods Using Shallow-Dish Combustion Chamber in an HSDI Common-Rail Diesel Engine Yoshihiro
More informationStudy of the Effect of CR on the Performance and Emissions of Diesel Engine Using Butanol-diesel Blends
International Journal of Current Engineering and Technology E-ISSN 77 416, P-ISSN 47 5161 16 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Research Article Study of the
More informationPPC FOR LOW LOAD CONDITIONS IN MARINE ENGINE USING COMPUTATIONAL AND EXPERIMENTAL TECHNIQUES
PPC FOR LOW LOAD CONDITIONS IN MARINE ENGINE USING COMPUTATIONAL AND EXPERIMENTAL TECHNIQUES Presented By:Kendra Shrestha Authors: K.Shrestha, O.Kaario, M. Imperato, T. Sarjovaara, M. Larmi Internal Combusion
More informationAssessment of Innovative Bowl Geometries over Different Swirl Ratios/EGR rates
Assessment of Innovative Bowl Geometries over Different Swirl Ratios/EGR rates Andrea Bianco 1, Federico Millo 2, Andrea Piano 2, Francesco Sapio 2 1: POWERTECH Engineering S.r.l., Turin ITALY 2: Politecnico
More informationAdvanced Diesel Combustion Concept: PCCI - A Step Towards Meeting BS VI Emission Regulations
October - November 2015 1. Advanced Diesel Combustion Concept: PCCI - A Step Towards Meeting BS VI Emission Regulations 2. ARAI offers Indigenously Developed Downsized 3 Cylinder High Power Density CRDI
More informationComparative performance and emissions study of a lean mixed DTS-i spark ignition engine operated on single spark and dual spark
26 IJEDR Volume 4, Issue 2 ISSN: 232-9939 Comparative performance and emissions study of a lean mixed DTS-i spark ignition engine operated on single spark and dual spark Hardik Bambhania, 2 Vijay Pithiya,
More informationExperimental Investigation of Performance and Exhaust Emission Characteristics of Diesel Engine by Changing Piston Geometry
Experimental Investigation of Performance and Exhaust Emission Characteristics of Diesel Engine by Changing Piston Geometry 1 Vaibhav Bhatt, 2 Vandana Gajjar 1 M.E. Scholar, 2 Assistant Professor 1 Department
More informationInfluence of Fuel Injector Position of Port-fuel Injection Retrofit-kit to the Performances of Small Gasoline Engine
Influence of Fuel Injector Position of Port-fuel Injection Retrofit-kit to the Performances of Small Gasoline Engine M. F. Hushim a,*, A. J. Alimin a, L. A. Rashid a and M. F. Chamari a a Automotive Research
More informationEffect of Varying Load on Performance and Emission of C.I. Engine Using WPO Diesel Blend
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 2 Ver. V (Mar - Apr. 2015), PP 37-44 www.iosrjournals.org Effect of Varying Load on Performance
More informationCONTROL OF POLLUTANTS WITH CATALYTIC CONVERTER AND COPPER COATED CYLINDER HEAD IN METHANOL- GASOLINE BLEND OPERATED TWO STROKE SI ENGINE
International Journal of Mechanical Engineering and Technology (IJMET) Volume 6, Issue 6, June 2015, pp. 132-138, Article ID: IJMET_06_06_013 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=6&itype=6
More informationResearch Article. Effect of exhaust gas recirculation on NOx emission of a annona methyl ester operated diesel engine
Available online www.jocpr.com Journal of Chemical and Pharmaceutical Research, 2015, 7(5):723-728 Research Article ISSN : 0975-7384 CODEN(USA) : JCPRC5 Effect of exhaust gas recirculation on NOx emission
More informationDual Fuel Engine Charge Motion & Combustion Study
Dual Fuel Engine Charge Motion & Combustion Study STAR-Global-Conference March 06-08, 2017 Berlin Kamlesh Ghael, Prof. Dr. Sebastian Kaiser (IVG-RF), M. Sc. Felix Rosenthal (IFKM-KIT) Introduction: Operation
More informationINVESTIGATIONS OF EFFECTS OF PILOT INJECTION WITH CHANGE IN LEVEL OF COMPRESSION RATIO IN A COMMON RAIL DIESEL ENGINE
INVESTIGATIONS OF EFFECTS OF PILOT INJECTION WITH CHANGE IN LEVEL OF COMPRESSION RATIO IN A COMMON RAIL DIESEL ENGINE by Nilesh GAJARLAWAR, Ajaykumar KHETAN a and Gaddale Amba Prasad RAO b* a Mahindra
More informationInvestigation on Diesel Engine for Airflow and Combustion in a Hemispherical Combustion Chamber
International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347 5161 2015INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Research Article Investigation
More informationEXPERIMENTAL AND THEORETICAL INVESTIGATION ON PERFORMANCE AND EMISSION CHARACTERISTICS OF DIESEL FUEL BLENDS
Int. J. Chem. Sci.: 14(4), 2016, 2967-2972 ISSN 0972-768X www.sadgurupublications.com EXPERIMENTAL AND THEORETICAL INVESTIGATION ON PERFORMANCE AND EMISSION CHARACTERISTICS OF DIESEL FUEL BLENDS M. VENKATRAMAN
More informationEXPERIMENTAL INVESTIGATION OF THE EFFECT OF HYDROGEN BLENDING ON THE CONCENTRATION OF POLLUTANTS EMITTED FROM A FOUR STROKE DIESEL ENGINE
EXPERIMENTAL INVESTIGATION OF THE EFFECT OF HYDROGEN BLENDING ON THE CONCENTRATION OF POLLUTANTS EMITTED FROM A FOUR STROKE DIESEL ENGINE Haroun A. K. Shahad hakshahad@yahoo.com Department of mechanical
More informationExperimental Investigation on Modification of Inlet poppet valve of single cylinder Direct Ignition Four stroke Diesel Engine
Experimental Investigation on Modification of Inlet poppet valve of single cylinder Direct Ignition Four stroke Diesel Engine Dr. Hiregoudar Yerrennagoudaru 1, Shiva prasad Desai 2, Mallikarjuna. A 3 1
More informationINVESTIGATIONS ON THE EFFECT OF MAHUA BIOFUEL BLENDS AND LOAD ON PERFORMANCE AND NOX EMISSIONS OF DIESEL ENGINE USING RESPONSE SURFACE METHODOLOGY
International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 8, August 2017, pp. 1417 1423, Article ID: IJMET_08_08_146 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=8
More informationRecent Advances in DI-Diesel Combustion Modeling in AVL FIRE A Validation Study
International Multidimensional Engine Modeling User s Group Meeting at the SAE Congress April 15, 2007 Detroit, MI Recent Advances in DI-Diesel Combustion Modeling in AVL FIRE A Validation Study R. Tatschl,
More informationSystem Simulation for Aftertreatment. LES for Engines
System Simulation for Aftertreatment LES for Engines Christopher Rutland Engine Research Center University of Wisconsin-Madison Acknowledgements General Motors Research & Development Caterpillar, Inc.
More informationCrankcase scavenging.
Software for engine simulation and optimization www.diesel-rk.bmstu.ru The full cycle thermodynamic engine simulation software DIESEL-RK is designed for simulating and optimizing working processes of two-
More informationEFFECT OF COMBUSTION CHAMBER GEOMETRY ON PERFORMANCE, COMBUSTION, AND EMISSION OF DIRECT INJECTION DIESEL ENGINE WITH ETHANOL-DIESEL BLEND
Venkadesan, G., et al.: Effect of Combustion Chamber Geometry on Performance... S937 EFFECT OF COMBUSTION CHAMBER GEOMETRY ON PERFORMANCE, COMBUSTION, AND EMISSION OF DIRECT INJECTION DIESEL ENGINE WITH
More informationExperimental investigations on the performance characteristic of diesel engine using n- butyl alcohols
Experimental investigations on the performance characteristic of diesel engine using n- butyl alcohols M. Karthe Assistant Professor, Department of Mechanical Engineering, M.KumarasamyCollege of Engineering,
More informationCombustion and Emission Characteristics of Jatropha Blend as a Biodiesel for Compression Ignition Engine with Variation of Compression Ratio
International Review of Applied Engineering Research. ISSN 2248-9967 Volume 4, Number 1 (2014), pp. 39-46 Research India Publications http://www.ripublication.com/iraer.htm Combustion and Emission Characteristics
More informationDESIGN OF THROTTLE BODY: A COMPARATIVE STUDY OF DIFFERENT SHAFT PROFILES USING CFD ANALYSIS
Int. J. Chem. Sci.: 14(S2), 2016, 681-686 ISSN 0972-768X www.sadgurupublications.com DESIGN OF TROTTLE BODY: A COMARATIVE STUDY OF DIFFERENT SAFT ROFILES USING CFD ANALYSIS M. BALAJI *, K. AMAL SATEES,
More informationImpact of Cold and Hot Exhaust Gas Recirculation on Diesel Engine
RESEARCH ARTICLE OPEN ACCESS Impact of Cold and Hot Exhaust Gas Recirculation on Diesel Engine P. Saichaitanya 1, K. Simhadri 2, G.Vamsidurgamohan 3 1, 2, 3 G M R Institute of Engineering and Technology,
More informationEXPERIMENTAL INVESTIGATION OF A SINGLE CYLINDER 4- STROKE DI DIESEL ENGINE BY SWIRL INDUCTION WITH TWO DIFFERENT CONFIGURATION PISTONS
EXPERIMENTAL INVESTIGATION OF A SINGLE CYLINDER 4- STROKE DI DIESEL ENGINE BY SWIRL INDUCTION WITH TWO DIFFERENT CONFIGURATION PISTONS B.MADHUBABU 1, Prof. K. GOVINDARAJULU 2 and Dr.S.L.V.PRASAD 3 1 Lecturer
More informationPerformance Enhancement of Multi-Cylinder Common Rail Diesel Engine for Automotive Application
Performance Enhancement of Multi-Cylinder Common Rail Diesel Engine for Automotive Application SUNDHARAM K, PG student, Department of Mechanical Engineering, Internal Combustion Engineering Divisions,
More informationFlow Simulation of Diesel Engine for Prolate Combustion Chamber
IJIRST National Conference on Recent Advancements in Mechanical Engineering (RAME 17) March 2017 Flow Simulation of Diesel Engine for Prolate Combustion Chamber R.Krishnakumar 1 P.Duraimurugan 2 M.Magudeswaran
More informationComparison of Swirl, Turbulence Generating Devices in Compression ignition Engine
Available online atwww.scholarsresearchlibrary.com Archives of Applied Science Research, 2016, 8 (7):31-40 (http://scholarsresearchlibrary.com/archive.html) ISSN 0975-508X CODEN (USA) AASRC9 Comparison
More informationHERCULES-2 Project. Deliverable: D8.8
HERCULES-2 Project Fuel Flexible, Near Zero Emissions, Adaptive Performance Marine Engine Deliverable: D8.8 Study an alternative urea decomposition and mixer / SCR configuration and / or study in extended
More informationInfluence of ANSYS FLUENT on Gas Engine Modeling
Influence of ANSYS FLUENT on Gas Engine Modeling George Martinas, Ovidiu Sorin Cupsa 1, Nicolae Buzbuchi, Andreea Arsenie 2 1 CERONAV 2 Constanta Maritime University Romania georgemartinas@ceronav.ro,
More informationR&D on Environment-Friendly, Electronically Controlled Diesel Engine
20000 M4.2.2 R&D on Environment-Friendly, Electronically Controlled Diesel Engine (Electronically Controlled Diesel Engine Group) Nobuyasu Matsudaira, Koji Imoto, Hiroshi Morimoto, Akira Numata, Toshimitsu
More informationCOLD FLOW ANALYSIS OF A SINGLE CYLINDER FOUR STROKE DIRECT INJECTION CI ENGINE AND ANALYSIS OF VOLUME FRACTION OF AIR USING CFD TECHNIQUE
COLD FLOW ANALYSIS OF A SINGLE CYLINDER FOUR STROKE DIRECT INJECTION CI ENGINE AND ANALYSIS OF VOLUME FRACTION OF AIR USING CFD TECHNIQUE Basanagouda C Biradar 1, Dr. S Kumarappa 2, Sarvanakumar Kandasamy
More informationGeneration of Air Swirl through Inlet Poppet Valve Modification and To Enhance Performance on Diesel Engine
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 6 Ver. VI (Nov. - Dec. 2015), PP 55-65 www.iosrjournals.org Generation of Air Swirl through
More informationNational Conference on Advances in Mechanical Engineering Science (NCAMES-2016)
Effect of Injection Timing on Performance and Emission of a Direct Injection Diesel Engine Fueled with Simarouba Biodiesel blend Srinath Pai 1, Akshath Shettigara 2, Dr. Abdul Sharief 3, Dr. Shiva kumar
More informationInvestigation of Engine Performance using Emulsified Diesel fuel
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 14, Issue 2 Ver. IV (Mar. - Apr. 2017), PP 79-87 www.iosrjournals.org Investigation of Engine Performance
More informationFoundations of Thermodynamics and Chemistry. 1 Introduction Preface Model-Building Simulation... 5 References...
Contents Part I Foundations of Thermodynamics and Chemistry 1 Introduction... 3 1.1 Preface.... 3 1.2 Model-Building... 3 1.3 Simulation... 5 References..... 8 2 Reciprocating Engines... 9 2.1 Energy Conversion...
More informationEXPERIMENTAL INVESTIGATION OF EXHAUST FROM COMPRESSION IGNITION ENGINE BASED AUTOMOBILES USING AN INNOVATIVE CATALYTIC CONVERTER DURING EMISSIONS TEST
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 13, December 2018, pp. 906 912, Article ID: IJMET_09_13_094 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=13
More informationGas exchange and fuel-air mixing simulations in a turbocharged gasoline engine with high compression ratio and VVA system
Third Two-Day Meeting on Internal Combustion Engine Simulations Using the OpenFOAM technology, Milan 22 nd -23 rd February 2018. Gas exchange and fuel-air mixing simulations in a turbocharged gasoline
More informationEXPERIMENTAL INVESTIGATION OF RHOMBUS SHAPED GROOVES ON PISTON CROWN OF A SINGLE CYLINDER 4-STROKE DI DIESEL ENGINE
Int. J. Mech. Eng. & Rob. Res. 2015 J Paul Rufus Babu et al., 2015 Research Paper ISSN 2278 0149 www.ijmerr.com Vol. 4, No. 1, January 2015 2015 IJMERR. All Rights Reserved EXPERIMENTAL INVESTIGATION OF
More informationThe influence of thermal regime on gasoline direct injection engine performance and emissions
IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS The influence of thermal regime on gasoline direct injection engine performance and emissions To cite this article: C I Leahu
More informationRESEARCH ON STEPS TAKEN TO MEET BSIV EMISSION NORMS WITH SINGLE CYLINDER AIR COOLED DIESEL ENGINE & CONVENTIONAL INJECTION SYSTEM
RESEARCH ON STEPS TAKEN TO MEET BSIV EMISSION NORMS WITH SINGLE CYLINDER AIR COOLED DIESEL ENGINE & CONVENTIONAL INJECTION SYSTEM Rahul Katariya 1, Ashok. J. Keche 2 1 M Tech. Scholar - Mechanical, MIT,
More informationSaud Bin Juwair, Taib Iskandar Mohamad, Ahmed Almaleki, Abdullah Alkudsi, Ibrahim Alshunaifi
The effects of research octane number and fuel systems on the performance and emissions of a spark ignition engine: A study on Saudi Arabian RON91 and RON95 with port injection and direct injection systems
More informationExperimental investigation of ethanol-gasoline dual-fuel on particle emissions at the exhaust of a small displacement engine
Experimental investigation of ethanol-gasoline dual-fuel on particle emissions at the exhaust of a small displacement engine F. Catapano, S. Di Iorio, P. Sementa, B. M. Vaglieco Istituto Motori CNR, Naples
More informationCONSEIL INTERNATIONAL DES MACHINES A COMBUSTION INTERNATIONAL COUNCIL ON COMBUSTION ENGINES
CONSEIL INTERNATIONAL DES MACHINES A COMBUSTION INTERNATIONAL COUNCIL ON COMBUSTION ENGINES PAPER NO.: 253 Experimental Experience Gained with a Long-Stroke Medium-Speed Diesel Research engine using Two
More informationEXPERIMENTAL INVETIGATIONN ON PERFORMANCE AND EMISSION CHARACTERISTICS OF DI- CI ENGINE FUELED WITH PREHEATED SHEA OLEIN BIODIESEL
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 11, November 2018, pp. 2006 2014, Article ID: IJMET_09_11 211 Available online at http://www.ia aeme.com/ijmet/issues.asp?jtype=ijmet&vtype=
More informationAustralian Journal of Basic and Applied Sciences
AENSI Journals Australian Journal of Basic and Applied Sciences ISSN:1991-8178 Journal home page: www.ajbasweb.com Efficient and Environmental Friendly NO x Emission Reduction Design of Aero Engine Gas
More informationEXHAUST GAS HEAT UTILIZATION IN IC ENGINES USING PRE-HEATER
International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 8, August 2017, pp. 1321 1326, Article ID: IJMET_08_08_134 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=8
More informationAnalysis of Emission characteristics on Compression Ignition Engine using Dual Fuel Mode for Variable Speed
International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 4, Issue 3 (October 2012), PP. 23-27 Analysis of Emission characteristics on Compression
More informationFigure 1: The spray of a direct-injecting four-stroke diesel engine
MIXTURE FORMATION AND COMBUSTION IN CI AND SI ENGINES 7.0 Mixture Formation in Diesel Engines Diesel engines can be operated both in the two-stroke and four-stroke process. Diesel engines that run at high
More informationInternational Journal of Scientific & Engineering Research, Volume 7, Issue 8, August-2016 ISSN
ISSN 2229-5518 2417 Experimental Investigation of a Two Stroke SI Engine Operated with LPG Induction, Gasoline Manifold Injection and Carburetion V. Gopalakrishnan and M.Loganathan Abstract In this experimental
More informationExperimental Investigations on a Four Stoke Diesel Engine Operated by Jatropha Bio Diesel and its Blends with Diesel
International Journal of Manufacturing and Mechanical Engineering Volume 1, Number 1 (2015), pp. 25-31 International Research Publication House http://www.irphouse.com Experimental Investigations on a
More informationINTERNATIONAL CONFERENCE ON RECENT ADVANCEMENT IN MECHANICAL ENGINEERING &TECHNOLOGY (ICRAMET 15)
EFFECT OF SPARK ASSISTED DIESEL ENGINE USING ETHANOL AND BIO DIESEL BLEND AS A FUEL *L.Vijayabaskar, N.Radhakrishnan, Dr.V.Gnanamoorthi Department of Mechanical Engineering University College of Engineering,
More informationSimulation of Performance Parameters of Spark Ignition Engine for Various Ignition Timings
Research Article International Journal of Current Engineering and Technology ISSN 2277-4106 2013 INPRESSCO. All Rights Reserved. Available at http://inpressco.com/category/ijcet Simulation of Performance
More informationInternal Combustion Engines
Emissions & Air Pollution Lecture 3 1 Outline In this lecture we will discuss emission control strategies: Fuel modifications Engine technology Exhaust gas aftertreatment We will become particularly familiar
More informationCFD Analysis for Designing Fluid Passages of High Pressure Reciprocating Pump
ISSN 2395-1621 CFD Analysis for Designing Fluid Passages of High Pressure Reciprocating Pump #1 SuhasThorat, #2 AnandBapat, #3 A. B. Kanase-Patil 1 suhas31190@gmail.com 2 dkolben11@gmail.com 3 abkanasepatil.scoe@sinhgadedu.in
More informationTHE USE OF Φ-T MAPS FOR SOOT PREDICTION IN ENGINE MODELING
THE USE OF ΦT MAPS FOR SOOT PREDICTION IN ENGINE MODELING Arturo de Risi, Teresa Donateo, Domenico Laforgia Università di Lecce Dipartimento di Ingegneria dell Innovazione, 731 via Arnesano, Lecce Italy
More informationEXPERIMENTAL INVESTIGATION OF FOUR STROKE SINGLE CYLINDER DIESEL ENGINE WITH OXYGENATED FUEL ADDITIVES
EXPERIMENTAL INVESTIGATION OF FOUR STROKE SINGLE CYLINDER DIESEL ENGINE WITH OXYGENATED FUEL ADDITIVES 1 Bhavin Mehta, 2 Hardik B. Patel 1,2 harotar University of Science & Technology, Changa, Gujarat,
More informationRavichandran ANNAMALAI a*, Rajan KUPPUSAMY a, and Senthilkumar KRISHNAN RAMACHANDRAN b
THERMAL SCIENCE: Year 218, Vol. 22, No. 3, pp. 1445-1456 1445 EFFECT OF PISTON BOWL GEOMETRY AND DIFFERENT INJECTION PRESSURE ON THE PERFORMANCE, EMISSION, AND COMBUSTION CHARACTERISTICS OF DIESEL ENGINE
More informationA Study of EGR Stratification in an Engine Cylinder
A Study of EGR Stratification in an Engine Cylinder Bassem Ramadan Kettering University ABSTRACT One strategy to decrease the amount of oxides of nitrogen formed and emitted from certain combustion devices,
More informationTHE INFLUENCE OF THE SIZE AND SHAPE OF THE CENTRAL BODY OF A COMBUSTION CHAMBER ON THE TOXICITY OF THE EXHAUST GASES IN THE URSUS 4390 ENGINE
Journal of KONES Powertrain and Transport, Vol. 23, No. 2 2016 THE INFLUENCE OF THE SIZE AND SHAPE OF THE CENTRAL BODY OF A COMBUSTION CHAMBER ON THE TOXICITY OF THE EXHAUST GASES IN THE URSUS 4390 ENGINE
More informationOptical Techniques in Gasoline Engine Performance and Emissions Development
Optical Techniques in Gasoline Engine Performance and Emissions Development TC GDI engines: analysis and development techniques to solve pre-ignition and soot formation issues Ernst Winklhofer AVL List
More informationPOSIBILITIES TO IMPROVED HOMOGENEOUS CHARGE IN INTERNAL COMBUSTION ENGINES, USING C.F.D. PROGRAM
POSIBILITIES TO IMPROVED HOMOGENEOUS CHARGE IN INTERNAL COMBUSTION ENGINES, USING C.F.D. PROGRAM Alexandru-Bogdan Muntean *, Anghel,Chiru, Ruxandra-Cristina (Dica) Stanescu, Cristian Soimaru Transilvania
More informationModule 3: Influence of Engine Design and Operating Parameters on Emissions Lecture 14:Effect of SI Engine Design and Operating Variables on Emissions
Module 3: Influence of Engine Design and Operating Parameters on Emissions Effect of SI Engine Design and Operating Variables on Emissions The Lecture Contains: SI Engine Variables and Emissions Compression
More informationENHANCEMENT OF A FOUR CYLINDER HCNG
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 11, November 2018, pp.2206 2212, Article ID: IJMET_09_11_233 Available online at http://www.ia aeme.com/ijmet/issues.asp?jtype=ijmet&vtype=
More informationThe influence of fuel injection pump malfunctions of a marine 4-stroke Diesel engine on composition of exhaust gases
Article citation info: LEWIŃSKA, J. The influence of fuel injection pump malfunctions of a marine 4-stroke Diesel engine on composition of exhaust gases. Combustion Engines. 2016, 167(4), 53-57. doi:10.19206/ce-2016-405
More information* Corresponding author
Characterization of Dual-Fuel PCCI Combustion in a Light-Duty Engine S. L. Kokjohn * and R. D. Reitz Department of Mechanical Engineering University of Wisconsin - Madison Madison, WI 5376 USA Abstract.
More informationEFFECT OF EGR AND CYCLONIC SEPARATOR ON EMISSIONS IN DI DIESEL ENGINES
Proceedings of the International Conference on Mechanical Engineering 27 (ICME27) 29-31 December 27, Dhaka, Bangladesh ICME7-TH-9 EFFECT OF EGR AND CYCLONIC SEPARATOR ON EMISSIONS IN DI DIESEL ENGINES
More informationSingle Cylinder 4 Stroke VCR Diesel Engine Performance And Analysis At Various Blends Of Fuels Under Various Cooling Rates
ISSN: 2278 0211 (Online) Single Cylinder 4 Stroke VCR Diesel Engine Performance And Analysis At Various Blends Of Fuels Under Various Cooling Rates B Lakshmana Swamy Associate Professor, Mechanical Engineering
More informationLoad Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine
IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 08, 2015 ISSN (online): 2321-0613 Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4
More informationEffect of Induced Turbulence in a C.I Engine by Varying Compression Ratio and Injection Timing on the Performance of the Engine
Effect of Induced Turbulence in a C.I Engine by Varying Compression Ratio and Injection Timing on the Performance of the Engine K. Srinivasa Raghavan Dr. V. Pandurangadu Mechanical engineering department
More informationCOMBUSTION STUDY AND EMISSION CHARACTERISTICS OF BLENDS OF DIESEL AND HYTHANE FOR GAS TURBINE ENGINES
International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 6, November December 2016, pp.105 113, Article ID: IJMET_07_06_011 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=6
More information