Repair Manual and Spare Parts List
|
|
- Stephanie Harris
- 6 years ago
- Views:
Transcription
1 Pneumatic Drive Unit Type Techn. Doc. No. 352 and Accessories for Pipe Cutting Machine Darstellung kann vom Original abweichen Repair Manual and _Inst_en_Version_02
2 Repair General In general, observe the safety regulations and instructions: refer to the operation and maintenance manual. The disassembly and re-assembly is done only according to the technical drawing. In case of damages, our service is at your disposal. Do not disassemble the tool until you know whether the problem is in one of the modules. Then only disassemble the tool as necessary to repair as required. Keep contaminants such as dirt and grit away from the internal parts at all times. Always identify and correct the cause of the problem prior to re-assembling. Further wear and tool failure can result, if the original cause is not corrected. Information for exact identification of the problem is given in the unit Troubleshooting of the operation manual. Notice: The particular installation direction of the parts mentioned in the following process instructions is indicated in the drawings and the parts lists at the end of this instruction. Spare Parts Only genuine Spitznas spare parts may be used. There is no warranty for damages and liability is disclaimed by Spitznas, if non-original spare parts and accessories are used. Disassembly Preparing of the pneumatic drive unit for disassembly Clean the exterior of the drive unit. Disconnect energy supply and secure against restart. Disconnect pneumatic hose. Take cutting tool item 11, respectively item 12 (page 6) out of the tool holder item 8, 9 (page 8) and store it at a safe place. Remove drive unit item 1 (page 5) by pulling the ball lock bolts items 5 and 6 (page 8). Disassembling drive unit modules Loosen 4 x M6 item 17 (page 17) and remove pneumatic motor item 1 from the gear item 2 (page 8). Loosen 4 x M6 item 39 (page 17) and remove cover hood item 3 (page 8) _Inst_en_Version_02 Page 1 of 38
3 Disassembling motor 4 x M6 item 17 were loosened (page 17) and pneumatic motor item 1 (page 8) was removed. Pull item 4 16 out of the motor housing item 1 (page 10). If necessary, continue disassembling according to the technical drawing. Disassembling gear Before, loosen 2 x M6 item 17 and remove pneumatic motor item 1. (see disassembling drive unit modules ) Remove snap ring item 37 (page 17), pull out lever item 35 together with items 33, 34 and 36. Continue disassembling, if necessary by knocking out the grooved cylindrical pin item 36. Loosen 4 x M6 item 29, pull the gear rim item 14 with the parts items 8, 9, 10, 11, 12, 13, 15 and 26 out of the gear housing item 1. Remove snap ring item 6 and pull pinion shaft item 2 with items 5 and 4 out of gear housing item 1. Loosen 4 x M5 item 32 and pull gear cover item 30 with the inner parts items 16, 19 and 24 out of gear housing item 1. Continue disassembling according to the technical drawings, if necessary. Re-assembly The re-assembly is done in the reverse order. Observe the following: Clean all parts before re-assembling. It is recommended to replace O-rings, bearings, radial shaft sealing rings and other sealings by new parts. Vanes are considered worn, when their width is less than 14.5 mm. replace Installation new In general, it is recommended to replace all wear parts during repair _Inst_en_Version_02 Page 2 of 38
4 If the bearings item 6 and item 14 in the end plates item 5 and 13 (page 10) have been replaced, the spacing has to be redone (see fig. end plate with spacer ring ). The spacer ring must be placed 0.04 / 0.05 mm in front of the end plate. For this, the inner ball bearing ring has to be pressed into the direction of the snap ring. End plate with spacer ring mm Lubricant Fill-up the gear with 25 g of grease. Grease SPITZNAS reference number: (400 g); (100 g) After finishing the assembly, a functional check of the drive unit must be done. (see technical specification of the operation and maintenance manual). Tighten all screws and nuts according to the instructions, when re-assembling. Tightening torques Item Description Torque Remark 21 Socket head screw M5 12 Nm Page 10 8 Hexagonal screw M5 12 Nm Page Socket head screw M6 18 Nm Page Socket head screw M6 18 Nm Page Counter sunk screw M5 12 Nm Page Socket head screw M6 18 Nm Page 17 8 Socket head screw M5 12 Nm Page 21 8 Socket head screw M5 12 Nm Page _Inst_en_Version_02 Page 3 of 38
5 Pipe cutting machine, assy. Item Qty. Description Part and drawing number Remarks 1 Pneumatic drive unit see separate list Accessories: 2 Guide carriage small see separate list 3 Chain tensioner small see separate list 4 Tensioning chain L = 950 mm 5 Guide carriage large see separate list 6 Chain tensioner large see separate list 7 Chain link Tightener see separate list 9 Tool set see separate list 11 Circular saw blade 180 mm Diamond 12 Circular saw blade 180 mm Carbide metal 13 1 Bevelling cutter Bevelling cutter Bevelling cutter Metal carrier box _Inst_en_Version_02 Page 4 of 38
6 Pipe cutting machine, assy _Inst_en_Version_02 Page 5 of 38
7 Pipe cutting machine, assy _Inst_en_Version_02 Page 6 of 38
8 Drive Unit Item Qty. Description Part and drawing no. Remarks 1 1 Pneumatic motor see separate list 2 1 Gearbox see separate list 3 1 Guard + water connection see separate list 4 1 Adjustment device Ball lock bolt mm 6 1 Ball lock bolt mm 7 1 Sensor block see separate list 8 1 Adapter Adapter Feeding pipe see page _Inst_en_Version_02 Page 7 of 38
9 Drive Unit _Inst_en_Version_02 Page 8 of 38
10 Pneumatic Motor Item Qty. Description Part and drawing no. Remarks 1 1 Motor housing with HC O-Ring * 3 1 O-Ring * 4 1 Cup spring End plate * 6 1 Grooved ball bearing * 7 1 Snap ring Spacer ring Cylinder bushing * 10 1 Tension sleeve Rotor * 12 4 Vane * 13 1 End plate * 14 1 Grooved ball bearing * 15 1 Snap ring Spacer ring Sound absorber Rotary sleeve Motor connection cover Quad-Ring * 21 5 Socket head screw Locking screw Pivoting connection, assy see separate list 30 1 Spacer ring O-Ring * 32 1 Shaft seal * 33 1 Coupling O-Ring * 35 1 Sound absorber O-Ring * * Wear parts to be stored in case of continuous use _Inst_en_Version_02 Page 9 of 38
11 Pneumatic Motor View rotated _Inst_en_Version_02 Page 10 of 38
12 Pivoting connection, assy Item Qty. Description Part and drawing no. Remarks 1 1 Pivoting connection housing Sealing Ball Switch part Socket, assy. with sealing Lever Washer Hexagonal screw _Inst_en_Version_02 Page 11 of 38
13 Pivoting connection, assy View rotated _Inst_en_Version_02 Page 12 of 38
14 Part and drawing number Sensor block Item Qty. Description Part and drawing no. Remarks 1 Sensor housing, assy item Sensor housing Control bushing Differential piston, assy item Differential piston O-Ring * 5 1 O-Ring * 6 1 O-Ring * 7 1 Pressure spring Guide bushing O-Ring * 12 1 Nipple Reducing nipple * Wear parts to be stored in case of continuous use _Inst_en_Version_02 Page 13 of 38
15 Part and drawing: Sensor block _Inst_en_Version_02 Page 14 of 38
16 Gearbox two-stage Item Qty. Description Part and drawing no. Remarks 1 1 Gearbox housing Pinion shaft, assy item Pinion shaft Pressure piece Snap ring Grooved ball bearing * 6 1 Snap ring Spur gear, assy item Spur gear Side pressure piece Needle sleeve * 1 Planet carrier, assy item Planet carrier Bearing needle * 12 3 Nadle cage * 13 3 Planet wheel Gear rim Grooved ball bearing * 16 1 Grooved ball bearing * 17 8 Socket head screw Gear pinion Planet carrier, assy item Planet carrier Planet wheel Bearing needle * 22 3 Nadle cage * 23 1 Gear rim Grooved ball bearing * 25 2 Grooved ball bearing * 26 4 Snap ring Adjusting washer _Inst_en_Version_02 Page 15 of 38
17 Gearbox two-stage Item Qty. Description Part and drawing no. Remarks 28 1 Shaft seal * 29 4 Socket head screw Gearbox cover Grooved ball bearing * 32 4 Counter sunk screw Eccentric disc Cylinder pin Lever Grooved cylindrical pin Snap ring Spring pressure piece Socket head screw Bushing * Wear parts to be stored in case of continuous use _Inst_en_Version_02 Page 16 of 38
18 Gearbox two-stage Glued with Loctite 243 glued mounted with surface seal _Inst_en_Version_02 Page 17 of 38
19 Gearbox two-stage glued _Inst_en_Version_02 Page 18 of 38
20 Guard with water connection Item Qty. Description Part and drawing no. Remarks 1 1 Guard, assy Splash guard, assy Star handle Threaded pin Tension sleeve Cup spring Pivot lock, assy item Pivot ring piece Gasket * 13 1 Hollow screw Gasket * 15 1 Ball valve with handle Connection Connection nipple Hose coupling with tensioning screw * 19 1 Sealing * Wear parts to be stored in case of continuous use _Inst_en_Version_02 Page 19 of 38
21 Part and drawing number. Guard with water connection _Inst_en_Version_02 Page 20 of 38
22 Adjustment device Item Qty. Description Part and drawing number Remarks 1 1 Sleeve Intermediate piece Scraper ring H * 4 1 Threaded head glued in place 5 1 Eye bolt Scraper ring H * 7 1 Spring washer Socket head screw Threaded pin glued in place 10 1 Rotary knob Bolt Bushing glued in place 13 1 O-Ring * _Inst_en_Version_02 Page 21 of 38
23 : Adjustment device _Inst_en_Version_02 Page 22 of 38
24 : Adapter for blade, assy Item Qty. Description Part and drawing number Remarks 1 1 Adapter for blade Clamp disc Nut Adapter ring ø22,2 u. 30 mm _Inst_en_Version_02 Page 23 of 38
25 Adapter for blade, assy _Inst_en_Version_02 Page 24 of 38
26 : Adapter for bevelling cutter, assy Item Qty. Description Part and drawing number Remarks 1 1 Adapter for bevelling cutter Feather key Spacer disc for 45 bevelling cutter Spacer disc for 60 bevelling cutter Spacer disc for radius cutter Capstan nut _Inst_en_Version_02 Page 25 of 38
27 Adapter for bevelling cutter, assy _Inst_en_Version_02 Page 26 of 38
28 : Guide carriage small Item Qty. Description Part and drawing number Remarks 1 1 Carriage Wheel bolt I Wheel bolt II Wheel I * 5 2 Wheel II * 6 2 Hook Nut Ball lock bolt Bushing glued in place * Wear parts to be stored in case of continuous use _Inst_en_Version_02 Page 27 of 38
29 Guide carriage small _Inst_en_Version_02 Page 28 of 38
30 : Chain tensioner small Item Qty. Description Part and drawing number Remarks 1 Chain tensioner Pos Sleeve Eye bolt Scraper H * 4 6 Cup spring O-Ring * 6 1 Threaded head glued in place 7 1 Spring washer Socket head screw Rotary knob Bolt glued in place 11 1 Tensioning chain (21 link) Chain lock Washer * Wear parts to be stored in case of continuous use _Inst_en_Version_02 Page 29 of 38
31 : Chain tensioner small _Inst_en_Version_02 Page 30 of 38
32 : Guide carriage large Item Qty. Description Part and drawing number Remarks 1 1 Carriage Wheel bolt Wheel bolt II Wheel I * 5 2 Wheel II * 6 1 Hook Nut glued in place 8 2 Ball lock bolt Bushing glued in place * Wear parts to be stored in case of continuous use _Inst_en_Version_02 Page 31 of 38
33 Guide carriage large _Inst_en_Version_02 Page 32 of 38
34 Chain tensioner large Item Qty. Description Part and drawing number Remarks 1 1 Rotary sleeve Eye bolt Eye bolt II Screwed lock pin glued in place 5 1 Threaded head Pressure spring Nut Wheel bolt Locking washer Wheel Washer Scraper H * 13 1 Tensioning chain (19 links) *Wear parts to be stored in case of continuous use _Inst_en_Version_02 Page 33 of 38
35 Chain tensioner large _Inst_en_Version_02 Page 34 of 38
36 : Tightener Set Item Qty. Description Part and drawing number Remarks 1 1 Spindle nut Spindle nut Spindle Tensioning segment small Tensioning segment small _Inst_en_Version_02 Page 35 of 38
37 Tightener Set _Inst_en_Version_02 Page 36 of 38
38 Tool Set Item Qty. Description Part and drawing number Remarks 1 Spanner AF Spanner AF Spanner AF Spanner AF Spanner AF Pin spanner _Inst_en_Version_02 Page 37 of 38
39 Translation of the original manual compiled:
Repair Manual and Spare Parts List
Hydraulic Drive Unit Type Techn. Doc. No. 362 and Accessories for Pipe Cutting Machine Darstellung kann vom Original abweichen Repair Manual and 580067000_Inst_en_Version_03 Repair General In general,
More informationHydraulic Rotary Hammer Drill
M a s c h i n e n f a b r i k G m b H Hydraulic Rotary Hammer Drill Type 2 2406 0010 Techn. Doc. No. 262 Illustration can differ from the original Repair Manual and Spare Parts List 224060010_Inst_en_Version_06.doc
More informationHydraulic Angle Grinder for Underwater Use Type
M a s c h i n e n f a b r i k G m b H Hydraulic Angle Grinder for Underwater Use Type 1 1585 0010 Illustration can differ from the original Repair Manual and Spare Parts List Compiled: 18.01.13 115850010_Inst_en_Version_03
More informationHydraulic Reciprocating Saw
Hydraulic Reciprocating Saw Type 5 1220 0050 Darstellung kann vom Original abweichen Repair Manual and Spare Parts List Compiled: 29.04.11 www.csunitec.com Page 1 of 16 REPAIR INSTRUCTION Do not disassemble
More informationPneumatic Circular Saw. Type Illustration can differ from the original. Spare Parts List
Pneumatic Circular Saw Type Illustration can differ from the original Cleaning Regular cleaning is required for a continuous and proper operation. Clean the housing regularly with a soft cloth, it is important
More informationPneumatic Angle Grinder also for Underwater Use Type
M a s c h i n e n f a b r i k G m b H Pneumatic Angle Grinder also for Underwater Use Type 1 4311 0050 Illustration can differ from the original Repair Manual and Spare Parts List Compiled: 22.06.11 143110050_Inst_en_Version_00
More informationPneumatic Axial Die Grinder also for Underwater Use Type , 0050
M a s c h i n e n f a b r i k G m b H Pneumatic Axial Die Grinder also for Underwater Use Type 1 5077 0010 0020, 0050 Illustration can differ from the original Repair Manual and Compiled: 18.07.11 150770010_0020_0050_Inst_en_Version_00
More informationHydraulic Impact Wrench Type
M a s c h i n e n f a b r i k G m b H Hydraulic Impact Wrench Type 6 1520 0010 Illustration can differ from the original Operation and Maintenance Manual 615200010_en_Version_03 Page 1 of 19 TECHNICAL
More informationCP3850 Series Grinders
1/11 1 Spring cylindrical 6156811670 1 1 1 1 1 1 1 X 2 Warning label 6158713860 1 1 1 1 1 1 1 X 3 CP plate 2050553403 1 1 1 1 1 1 1 X 4 Name plate 2050553413 1 1 1 1 1 1 1 X 5 Ring screw 6156731760 1 1
More informationPneumatic Corner Drill
Maschinenfabrik GmbH Pneumatic Corner Drill Type 2 1602 0030 Illustration can differ from the original Operation and Maintenance Manual Compiled: 31.07.08 216020030_en.doc Page 1 of 12 TECHNICAL SPECIFICATION
More informationCP3850 Series Grinders
1/11 1 Spring cylindrical 6156811670 1 1 1 1 1 X 2 Warning label 6158713860 1 1 1 1 1 X 3 CP plate 2050553403 1 1 1 1 1 X 4 Name plate 2050553413 1 1 1 1 1 X 5 Ring screw 6156731760 1 1 1 1 1 X 6 Autobalancer
More informationCB Spare parts list. Hydraulic concrete buster. CB 2500 s/n DEQ Construction Tools GmbH No
CB 2500 Spare parts list Hydraulic concrete buster CB 2500 s/n DEQ169050-2018 Construction Tools GmbH No. 3390787501 2018-11-22 General information This spare parts list applies to the following: Part
More informationUOW Series Repair Manual UOW-11 & UOW-T60 Series
UOW Series Repair Manual UOW-11 & UOW-T60 Series 100000 SE Pine St., Portland, OR 97216 800-852-1368 503-254-6600 www.aimco-global.com Contents Page 1. Tools Needed for Repair 2 2. Disassembly and Reassembly
More informationON-THE-VEHICLE BRAKE LATHE
800 ON-THE-VEHICLE BRAKE LATHE Parts Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the machine for ease
More informationPARTS LIST FOR NO. 3 SERIES PISTOL AND T HANDLE SCREWDRIVERS
PARTS LIST FOR NO. 3 SERIES PISTOL AND T HANDLE SCREWDRIVERS NON-REVERSING HANDLE ASSEMBLY (SERIAL NO S. STARTING WITH B & D ) Fig. Part Form A278F Date 10-00/B Page 1 of 6 4. 14309 Ring O 5. 14312 Ring
More informationBP 3050, 3050 R. Spare parts list. Bulk pulverizer. BP 3050 s/n DEQ BP 3050 R s/n DEQ
BP 3050, 3050 R Spare parts list Bulk pulverizer BP 3050 s/n DEQ169179 - BP 3050 R s/n DEQ169179-2018 Construction Tools GmbH No. 3390758101 2018-01-01 General information This spare parts list applies
More informationBP 2050, 2050 R. Spare parts list. Bulk pulverizer. BP 2050 s/n DEQ BP 2050 R s/n DEQ
BP 2050, 2050 R Spare parts list Bulk pulverizer BP 2050 s/n DEQ169181 - BP 2050 R s/n DEQ169181-2018 Construction Tools GmbH No. 3390756701 2018-01-01 General information This spare parts list applies
More informationSpare Parts List Hydraulic Cutter
Spare Parts List Hydraulic Cutter CombiCutter CC 1501 CC 1501 Part ident. 3363 0028 87 Valid from 02/2003 GB Spare Parts List Hydraulic Cutter CombiCutter CC 1501 Atlas Copco Construction Tools GmbH Atlas
More informationPrinted from MediaCat
Illustration A Crankcase, Crankshaft Illustration A Crankcase, Crankshaft Ref.Nr. Item code Quantity Description 1 1117 020 2106 1 Crankcase 2-9 2 9022 341 1050 4 Spline screw IS-M5x25 3 0000 988 5211
More informationPrinted from MediaCat
Illustration A Crankcase Illustration A Crankcase Ref.Nr. Item code Quantity Description 1 1106 020 2506 1 Crankcase (2) 2-11 2 0000 988 5217 1 Connector (2) 3 0000 988 5200 2 Connector (2) 4 1106 641
More informationSPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 240 R,
SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 240 R, 2005-09 ACCESSORIES 240 R, 2005-09 ACCESSORIES 240 R, 2005-09 Ref Part No Description Remark QTY KIT 501 19 22-01 TOOL CASING 1 501 60 02-03 SCREWDRIVER
More information1 RS-300/D 320/D 340/D 350H Parts Manual
300/D 320/D 340/D 350H Parts Manual Table Of Contents Three Point Hitch / Hitch Frame Assembly... 3 Tongue Pull Hitch Assembly... 7 Main Gearbox... 11 Crank Handle & Gear... 13 Hydraulic Lift... 15 Rotor
More informationSpare Parts List Hydraulic Cutter
Spare Parts List Hydraulic Cutter CombiCutter CC 4000 CC 4000 002582 Valid from: 07/2002 GB Spare Parts List Hydraulic Cutter CombiCutter CC 4000 Atlas Copco Construction Tools GmbH Atlas Copco Construction
More informationPrinted from MediaCat
Illustration A Crankcase, Cylinder Illustration A Crankcase, Cylinder Ref.Nr. Item code Quantity Description 1 1113 020 2107 1 Crankcase (1,2,4,5,7,8) 2-11 1 1113 020 2108 1 Crankcase (3,6) 2-11 2 1113
More informationUAN Series Pneumatic Nutrunner Repair Manual
UAN Series Pneumatic Nutrunner Repair Manual PO Box 16460, Portland, OR 97292-0460 503-254-6600 Fax 503-255-2615 www.aimco-global.com Contents Page 1. Tools Needed for Repair of UAN Series Pneumatic Nutrunner
More informationAIR POWERED CHAIN HOIST AL/AW/AS SERIES
EFFECTIVE: January 20, 207 AIR POWERED CHAIN HOIST AL/AW/AS SERIES ¼ Ton through 5 Ton Capacity Code Number and Serial Number WARNING This equipment should not be installed, operated or maintained by any
More informationConstructionParts.com
Main assy, engine plate and lower part 18213-2 6 Main assy, engine plate and lower part Item Part No Rem Qty Description 1 D391218-01 1 Engine plate 2 Handle ( Page 60 ) 3 Ground plate and eccentric element
More informationSPARE PARTS LIST CHAIN SAWS 365 H,
SPARE PARTS LIST CHAIN SAWS 365 H, 2013-12 ACCESSORIES 365 H, 2013-12 ACCESSORIES 365 H, 2013-12 Ref Part no. Description Remark Qty Kit 1 503 55 85-03 TOOL KIT 1 2 501 69 17-01 COMBINATION WRENCH 1 1
More informationSPARE PARTS LIST. CHAIN SAWS 365 H from
SPARE PARTS LIST CHAIN SAWS 365 H from 2017-11- ACCESSORIES 365 H from 2017-11- ACCESSORIES 365 H from 2017-11- Ref Part No Description Remark QTY KIT 1 503 55 85-03 TOOL KIT 1 2 501 69 17-01 COMBINATION
More informationMG Spare parts list. Multi grapple. MG 2700 s/n BGF Construction Tools GmbH No
MG 2700 Spare parts list Multi grapple MG 2700 s/n BGF057417-2017 Construction Tools GmbH No. 3390775501 2017-01-23 General information This spare parts list applies to the following: Part number Description
More informationSPARE PARTS LIST CHAIN SAWS CS2252,
SPARE PARTS LIST CHAIN SAWS CS2252, 2012-07 ACCESSORIES CS2252, 2012-07 ACCESSORIES CS2252, 2012-07 Ref Part no. Description Remark Qty Kit 1 575 43 92-01 TOOL 1 2 522 52 11-01 COMBINATION WRENCH 1 1 3
More informationPrinted from CyberCat-STIGA Section: GARDEN ELECTRICAL SYSTEM
Section: GARDEN ELECTRICAL SYSTEM Section: GARDEN ELECTRICAL SYSTEM 2312 2333 1 1 1134-3625-01 Harness 2 1 1134-3623-02.Interlock module 4 2 9849-8013-16 Screw 5 2 1134-3132-01 Cable holder 6 2 1134-3204-01
More informationPARTSBOOK. This part of the manual contains part numbers and illustrations based on the latest information available at the time of print.
2 PARTSBOOK This part of the manual contains part numbers and illustrations based on the latest information available at the time of print. Hall Manufacturing, Inc. reserves the right to make changes at
More informationMaintenance Information
04581245 Edition 2 May 2014 Air Grinder, Die Grinder and Sander Series G2 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,
More informationSPARE PARTS LIST. BRUSHCUTTERS/CLEARING SAWS 343 R from
SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 343 R from 2014-12 ACCESSORIES 343 R from 2014-12 ACCESSORIES 343 R from 2014-12 Ref Part No Description Remark QTY KIT 1 502 21 60-13 ACCESSORY BAG 1 2 501
More informationDPC6430. Documents DPC Tank and handle grips. 2 Hood, air filter. 3 Muffler, connecting muff. 4 Carburetor. 5 Starter assy., ignition assy.
Documents 1 Tank and handle grips 2 Hood, air filter 3 Muffler, connecting muff 4 Carburetor 5 Starter assy., ignition assy. 6 Cylinder, crankshaft, clutch 7 Cutting device, protection hood 8 Blades, tools
More informationSPARE PARTS LIST. CHAIN SAWS 365SP from
SPARE PARTS LIST CHAIN SAWS 365SP from 2018-01- CHAIN BRAKE & CLUTCH COVER 365SP from 2018-01- CHAIN BRAKE & CLUTCH COVER 365SP from 2018-01- Ref Part No Description Remark QTY KIT 1 525 75 52-01 SCREW
More informationDrawing A Crankcase 041 AV SCS
Drawing A Crankcase 1 Drawing A Crankcase Reference Item number Qty Description 1 1110 020 2105 1 Crankcase 2-5, 9, 10, 12 2 9371 470 3120 2 Cylindrical pin 6x20 3 9048 216 1010 8 Pan head screw M5x18
More informationDrawing A Crankcase. Drawing A Crankcase
Drawing A Crankcase Drawing A Crankcase 1 1122 020 2101 1 Crankcase 2-18 2 9022 341 1300 2 Spline screw IS-M6x20 3 0000 988 5211 1 Connector 4 9371 470 2610 2 Cylindrical pin 5x18 5 0000 974 1200 1 Notched
More informationSPARE PARTS LIST POLE PRUNER/POLE SAWS 327 P4
SPARE PARTS LIST POLE PRUNER/POLE SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 537 04 07-10 ACCESSORY BAG 1 2 501 69 17-01 COMBINATION WRENCH 1 3 502 21 58-01 WRENCH 1 4 503 97
More informationSPARE PARTS LIST TRIMMERS/EDGERS 325 E X-SERIES,
SPARE PARTS LIST TRIMMERS/EDGERS 325 E X-SERIES, 2001-01 ACCESSORIES 325 E X-SERIES, 2001-01 ACCESSORIES 325 E X-SERIES, 2001-01 Ref Part No Description Remark QTY KIT 501 60 02-03 SCREWDRIVER 1 502 11
More informationPARTS LIST, PRESSURE CYLINDER
PARTS LIST, PRESSURE CYLINDER KEY QTY. PART NO. DESCRIPTION 1 1 306650 Valve sleeve (tension) 2 1 306651 Valve stem (tension) 3 1 306652 Valve sleeve (seal) 4 1 306653 Valve stem (seal) 5 1 306657 Catch
More information1 KW-550T Parts Manual. Table Of Contents
KW-550T Parts Manual Table Of Contents Drawbar... 2 Central Gearbox - Serial No. 523800-554988... 4 Central Gearbox - Serial No. 523800-554988... 6 Central Gearbox - Serial No. 554989-... 8 Central Gearbox
More information1 KW-880 Parts Manual
Headstock... 2 Hitch Beam... 4 Central Gearbox... 6 Central Gearbox... 8 Intermediate Beam... 10 Intermediate Beam... 12 Intermediate Beam Outside... 14 Intermediate Beam Outside... 16 Outer Support Tube...
More informationRemanufactured Transmissions, Spare Parts, and Kits Catalog
S6-650 Spare Parts - Gearbox Housing Group 01.010 1319 301 025 Main Housing without Check Valve 005/006/045/046/049/050 1319 301 093 Main Housing without Check Valve 083/085/084/086 1319 301 084 Main Housing
More informationFANEX 833 T / Table of Contents
FANEX 833 T / Table of Contents PosNo. Assembly group Page B MIDDLE GEAR BOX 1 B CIRCLE GEAR BOX 2 B DRIVE SHAFT 3 B SIMPLE JOINT WALTERSCHEID 4 B WINDROWING GEAR W 5 B GEAR BOX W 6 B UNIV.PROP.SHAFT LZ=1260
More informationSPARE PARTS LIST. POLE PRUNER/POLE SAWS 327 P5x
SPARE PARTS LIST POLE PRUNER/POLE SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 537 04 07-10 ACCESSORY BAG 1 2 501 69 17-01 COMBINATION WRENCH 1 3 502 21 58-01 WRENCH 1 4 503 98
More informationSPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 223 L,
SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 223 L, 2006-01 ACCESSORIES 223 L, 2006-01 ACCESSORIES 223 L, 2006-01 Ref Part No Description Remark QTY KIT 1 501 78 33-01 SUSPENSION BAIL 1 2 503 21 83-16 SCREW
More informationSPARE PARTS LIST CHAIN SAWS GZ550
SPARE PARTS LIST CHAIN SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 501 69 17-01 COMBINATION WRENCH 1 CARBURETOR & AIR FILTER CARBURETOR & AIR FILTER Ref Part No Description Remark
More informationMG 400. Spare parts list. Multi grapple. MG 400 s/n BGF Construction Tools GmbH No
MG 400 Spare parts list Multi grapple MG 400 s/n BGF074759-2016 Construction Tools GmbH No. 3390774801 2016-07-21 General information This spare parts list applies to the following: Part number Description
More informationPrinted from MediaCat
Illustration A Crankcase Illustration A Crankcase Ref.Nr. Item code Quantity Description 1 1124 020 2116 1 Crankcase 2-15 2 0000 988 5215 1 Connector 3 9371 470 2610 2 Cylindrical pin 5x18 4 1120 162 5200
More informationDCS7901. Documents DCS Fuel tank, tubular grip. 2 Hood, air filter, muffler. 3 Cylinder, crankcase. 4 Ignition electronics, starter
Documents 1 Fuel tank, tubular grip 2 Hood, air filter, muffler 3 Cylinder, crankcase 4 Ignition electronics, starter 5 Oil pump, clutch 6 Chain brake 7 Carburetor 8 Special parts for version with electric
More informationSPARE PARTS LIST CHAIN SAWS CS2255
SPARE PARTS LIST CHAIN SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 501 69 17-01 COMBINATION WRENCH 1 CARBURETOR & AIR FILTER CARBURETOR & AIR FILTER Ref Part No Description Remark
More informationSPARE PARTS LIST RIDERS R322T AWD, , , ,
SPARE PARTS LIST RIDERS R322T AWD, 966785801, 967032101, 967153001, 2012-03 103CM CUTTING DECK R322T AWD, 966785801, 967032101, 967153001, 2012-03 103CM CUTTING DECK R322T AWD, 966785801, 967032101, 967153001,
More informationrev 1_09/20/2017 PS-35C EA3500SR
C 1 Tank, Handle 5 7 6 8 17 9 1 2 10 11 12 13 18 19 20 3 21 4 22 23 14 16 2 1 Tank, Handle 1 1 168507-3 TANK CAP COMPLETE 1 1 INC. 2 1 2 213080-9 O RING 29.5 1 1 1 3 163447-0 GASOLINE FILTER 1 1 1 4 195757-7
More informationSPARE PARTS LIST CHAIN SAWS CS2258,
SPARE PARTS LIST CHAIN SAWS CS2258, 2012-05 ACCESSORIES CS2258, 2012-05 ACCESSORIES CS2258, 2012-05 Ref Part no. Description Remark Qty Kit 1 575 43 92-01 TOOL 1 2 522 52 11-01 COMBINATION WRENCH 1 1 3
More informationRYOBI 10 in. SLIDING MITER SAW w/laser MODEL NO. TSS100L1 REPAIR SHEET
RYOBI 10 in. SLIDING MITER SAW w/laser MODEL NO. TSS100L1 REPAIR SHEET 32 96 119 31 1 85 116 86 114 92 82 117 113 112 115 97 1 6 121 1 84 59 81 87 122 128 34 174 80 66 88 114 19 79 78 115 117 116 125 126
More informationSPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS BC2145,
SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS BC2145, 2008-05 ACCESSORIES BC2145, 2008-05 ACCESSORIES BC2145, 2008-05 Ref Part No Description Remark QTY KIT 1 502 21 60-13 ACCESSORY BAG 1 2 501 60 02-03
More informationMaintenance Information
80234313 Edition 1 June 2006 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing
More informationSPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 535 RX
SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS ACCESSORIES ACCESSORIES Ref Part no. Description Remark Qty Kit 1 501 19 22-01 TOOL CASING 1 2 531 00 92-48 FILTER OIL Oil Airfilter 1 3 503 97 64-01 GREASE
More informationRYOBI 10 in. SLIDING MITER SAW w/laser MODEL NO. TSS100L REPAIR SHEET
RYOBI 10 in. SLIDING MITER SAW w/laser MODEL NO. TSS100L REPAIR SHEET 119 96 83 1 84 85 116 86 114 92 82 117 113 112 115 97 175 176 120 177 121 1 2 3 122 81 87 128 164 1 80 88 174 114 6 53 163 19 3 141
More informationSPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 343 F,
SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 343 F, 2011-02 ACCESSORIES 343 F, 2011-02 ACCESSORIES 343 F, 2011-02 Ref Part No Description Remark QTY KIT 1 502 21 60-13 ACCESSORY BAG 1 2 501 60 02-03 SCREWDRIVER
More informationSPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 336 FR
SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS BEVEL GEAR BEVEL GEAR Ref Part No Description Remark QTY KIT 1 544 21 64-01 GEAR 1 2 537 29 59-02 GEAR HOUSING 1 1 3 738 21 99-00 BALL BEARING 1 1 4 505 13 33-01
More informationRVDRT & RVVRT Model 404 to 408
All-Star 00% Oil Free Rotary Vane Pump & Compressor RVDRT & RVVRT Model 0 to 08 0 0 0 ( version RVDRT* pcs ) 30 3 3 33 3 35 0 (version RVVRT ) 3 ( version RVDRT ) 50 60 ( version RVDRT ) 70 ( version RVVRT
More informationTUBULAR HANDLE ASSY CLAMP FILLISTER HEAD SCREW 6X FILLISTER HEAD SCREW 5.5X20
1 1 038310020 TUBULAR HANDLE ASSY. 2 038310060 CLAMP 3 908006145 FILLISTER HEAD SCREW 6X14 4 913455204 FILLISTER HEAD SCREW 5.5X20 6 957114060 AIR VALVE CPL. 7 038114630 GRIP PLATE 8 038117020 CATCH LEVER
More informationDrawing A Cylinder, Engine pan
Drawing A Cylinder, Engine pan 1 Drawing A Cylinder, Engine pan Reference Item number Qty Description 1 4180 020 1207 1 Cylinder with piston Ø 38 mm (33.2008) 2-9, 16 2 4180 025 2002 2 Valve 3 4180 025
More informationS/N 1H019H - 1H310H Page 1 of 33 46" Cutting Deck Assembly
1180 S/N 1H019H - 1H310H Page 1 of 33 46" Cutting Deck Assembly 1180 S/N 1H019H - 1H310H Page 2 of 33 46" Cutting Deck Assembly 1 17982 1 S Reinforcement Spindle Plate 2 618-0430 1 S Spindle Assembly w/
More informationModels 820 and 840 2
Models 820 and 840 2 Models 820 and 840 1 783-0250 Hood 2 738-0952 Shld. Bolt.375" Dia. x.5" 3 736-0175 Spr. Washer.265" I.D. x.562" OD 4 710-0751 Hex Bolt 1/4-20 x.62" * 6 7-0271 Hex Sems Nut 1/4-20 Thd.
More informationSPARE PARTS LIST TRIMMERS/EDGERS 323 LD,
SPARE PARTS LIST TRIMMERS/EDGERS 323 LD, 2008-03 ACCESSORIES 323 LD, 2008-03 ACCESSORIES 323 LD, 2008-03 Ref Part No Description Remark QTY KIT 1 531 00 92-48 FILTER OIL 1 2 502 28 59-01 STOP 1 3 501 60
More informationPrinted from MediaCat
Illustration A Crankcase Illustration A Crankcase Ref.Nr. Item code Quantity Description 1 1119 020 2118 1 Crankcase (1,3,5) 2-11 1 1119 020 2109 1 Crankcase (6,8,9) 2-11 1 1119 020 2119 1 Crankcase (2,4)
More informationSPARE PARTS LIST RIDERS P525 D, , 2016
SPARE PARTS LIST RIDERS P525 D, 967602101, 2016 CABIN P525 D, 967602101, 2016 CABIN P525 D, 967602101, 2016 Ref Part No Description Remark QTY KIT 1 501 99 86-01 DOOR 1 2 501 99 87-01 SEAL 1 3 579 86 79-01
More informationSPARE PARTS LIST. POWER CUTTERS K960 Chain,
SPARE PARTS LIST POWER CUTTERS K960 Chain, 2008-03 AIR FILTER K960 Chain, 2008-03 AIR FILTER K960 Chain, 2008-03 Ref Part No Description Remark QTY KIT 1 503 21 53-45 SCREW ITXSCM 2 2 544 87 46-01 LABEL
More informationSPARE PARTS LIST RIDERS RIDER 111 B, , , , ,
SPARE PARTS LIST RIDERS RIDER 111 B, 965996801, 965996885, 966663185, 967186501, 2011-02 CHASSIS & ENCLOSURES RIDER 111 B, 965996801, 965996885, 966663185, 967186501, 2011-02 CHASSIS & ENCLOSURES RIDER
More informationForward and Reversing Vibrating Plate LH 300/700. Work Shop Manual WLHALLEN1, October 2001
Forward and Reversing Vibrating Plate LH 00/700 Work Shop Manual WLHALLEN, October 00 These instructions apply from: LH 00 S/N *00608* LH 700 S/N *700078* WLHALLEN We reserve the right to change specifications
More informationSPARE PARTS LIST WALL SAW WSE1621
SPARE PARTS LIST WALL SAW Index 000 EN Spare Parts List 10999154 de / 01.11.2018 How to use the spare parts list The spare parts list is not intended as instructions for assembly or dismantling work. It
More informationSection TS-1. Track Systems / 765 Undercarriage. 755/765 Track Frames - Frame and Covers
Section TS-1 Track Systems - 755 / 765 Undercarriage - Frame and Covers Last Updated - 01/17 Track Systems - 755-765 Undercarriage Parts T4176 1/17 12.50 TS-3-1 Track Systems - 755-765 Undercarriage Last
More informationSPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS BC2053
SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 523 11 16-01 BOX SPANNER 1 2 523 11 23-01 WRENCH 1 3 523 11 18-01 LEVER HANDLE 1 4 523 11 17-01
More informationSPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 325 RX,
SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 325 RX, 2008-03 ACCESSORIES 325 RX, 2008-03 ACCESSORIES 325 RX, 2008-03 Ref Part No Description Remark QTY KIT 1 531 00 92-48 FILTER OIL 1 2 502 28 59-01 STOP
More informationMG 300. Spare parts list. Multi grapple Atlas Copco Construction Tools GmbH No
MG 300 Spare parts list Multi grapple 0 Atlas Copco Construction Tools GmbH No. 3390 7354 0 0046 MG 300 Contents Contents General information................................................................
More informationParts Breakdown DCS9010
Page 1 of 12 2/8/2008 Page 2 of 12 2/8/2008 Page 3 of 12 2/8/2008 Page 4 of 12 2/8/2008 Page 5 of 12 2/8/2008 Page 6 of 12 2/8/2008 Page 7 of 12 2/8/2008 Page 8 of 12 2/8/2008 Fig # Part ID Part Name Quantity
More informationSPARE PARTS LIST CHAIN SAWS 455 E
SPARE PARTS LIST CHAIN SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 501 69 17-01 COMBINATION WRENCH 1 CARBURETOR & AIR FILTER CARBURETOR & AIR FILTER Ref Part No Description Remark
More informationSPARE PARTS LIST. CHAIN SAWS 455 Rancher
SPARE PARTS LIST CHAIN SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 501 69 17-01 COMBINATION WRENCH 1 CARBURETOR & AIR FILTER CARBURETOR & AIR FILTER Ref Part No Description Remark
More informationBEFCO. Parts Manual GREEN-RITE. One Pass Overseeder-Aerator and/or Seeder-Cultivator with Corrugated Roller for Lawn and Turf Operations
BEFCO Parts Manual GREENRITE One Pass OverseederAerator and/or SeederCultivator with Corrugated Roller for Lawn and Turf Operations GRT50 50, GRT5, GRT & GRT The operator's manual is a technical service
More informationMaintenance Information
16606022 Edition 3 May 2014 Air Drill 728 Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially
More information13AU609H063 (1999) Page 1 of 25 Axle & Wheels Front And Steering Assembly
13AU609H063 (1999) Page 1 of 25 Axle & Wheels Front And Steering Assembly 13AU609H063 (1999) Page 2 of 25 Axle & Wheels Front And Steering Assembly 1 683-0304 1 S Frame 2 710-0604A 1 /P Self-tapping Screw,
More informationS/N 1H019H - 1H310H Page 1 of 48 42" Cutting Deck Assembly
1170 S/N 1H019H - 1H310H Page 1 of 48 42" Cutting Deck Assembly 1170 S/N 1H019H - 1H310H Page 2 of 48 42" Cutting Deck Assembly 4 683-0254 1 S Deck Adjustment Bracket w/ Weld Nut 9 710-0528 1 /P Hex Cap
More informationModel No. EA6100P PETROL CHAIN SAW
1 / 6 2 / 6 3 / 6 4 / 6 5 / 6 6 / 6 1 / 5 Item Parts No. Description I/C Qty N/O Sales Purch. Note 001 181114202 TANK CAP CPL. 1 D10 INC. 2 002 963229036 PACKING RING 1 003 908006145 FILLISTER HEAD SCREW
More informationPTC 220 HD. Model Year 2011
Model Year 2011 Use GLOBAL GARDEN PRODUCT Genuine Spare Parts specified in the parts list for repair and/or replacement. The contents described in the parts list may change due to improvement. The drawings
More informationPull-Push Saw ERIKA 85 Ec
Pull-Push Saw ERIKA 85 Ec mafell@mafell.de 1 / 13 mafell@mafell.de 2 / 13 mafell@mafell.de 3 / 13 mafell@mafell.de 4 / 13 mafell@mafell.de 5 / 13 EAN name of price in Preisschlüssel 1 084598 4032689160320
More informationSPARE PARTS LIST CHAIN SAWS 365SP,
SPARE PARTS LIST CHAIN SAWS 365SP, 2013-12 ACCESSORIES 365SP, 2013-12 ACCESSORIES 365SP, 2013-12 Ref Part no. Description Remark Qty Kit 1 503 55 85-01 TOOL 1 2 501 69 17-01 COMBINATION WRENCH 1 1 3 503
More informationChain Box and Knife. Item # Description Part Number 180-D & GS
Chain Box and Knife Item # Description Part Number 180-D & GS 1 Groove pin 2275-03160 2 Hex cap screw 2175-03061 3 Washer 2275-03060 4 Setscrew 2175-07163 5 Chain box 4975-00355 6 Berkel logo 3175-00152
More informationMANUAL TRANSAXLE Return to Main Table of Contents
MANUAL TRANSAXLE Return to Main Table of Contents GENERAL... 2 MANUAL TRANSAXLE CONTROL... 12 SHIFT LEVER ASSEMBLY... 14 MANUAL TRANSAXLE... 15 MANUAL TRANSAXLE ASSEMBLY... 17 FIFTH SPEED SYNCHRONIZER
More informationSPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS GC2236,
SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS GC2236, 2013-06 ACCESSORIES GC2236, 2013-06 ACCESSORIES GC2236, 2013-06 Ref Part no. Description Remark Qty Kit 1 501 19 22-01 TOOL CASING 1 2 501 68 89-01 SLEEVE
More informationPetrol chainsaw----p File: Version: 1.0 Ihr Ersatzteilspezialist im Internet
Petrol chainsaw----p File: Version: 1.0 Spare Parts list File: 0040100903BD Version: 1.0 Petrol chainsaw----pcs46b Pos. No Part code English QTY 1 905207 front handle assy 1 B350012 2 Hexagon lobular
More informationParts Catalogue BT 98 HC. 2T /A11 - Season 2015
Parts Catalogue BT 98 HC 2T0620424/A11 - Season 2015 Use GLOBAL GARDEN PRODUCT Genuine Spare Parts specified in the parts list for repair and/or replacement. The contents described in the parts list may
More informationSPARE PARTS LIST. CHAIN SAWS 435 E from
SPARE PARTS LIST CHAIN SAWS 435 E from 2011-05- ACCESSORIES 435 E from 2011-05- ACCESSORIES 435 E from 2011-05- Ref Part No Description Remark QTY KIT 1 503 55 85-04 TOOL 1 CARBURETOR 435 E from 2011-05-
More informationMaintenance Information
80234313 Edition 2 May 2014 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the
More informationSPARE PARTS LIST. CHAIN SAWS 346 XP, from
SPARE PARTS LIST CHAIN SAWS 346 XP, from 2015-07 - ACCESSORIES 346 XP, from 2015-07 - ACCESSORIES 346 XP, from 2015-07 - Ref Part No Description Remark QTY KIT 1 503 55 85-01 TOOL 1 2 501 69 17-01 COMBINATION
More informationLIFT TRUCK SERIES: G35S-2 G40S-2 G45S-2 G40SC-2 G45SC-2 G50SC-2. November 15, 2000 CODE 3150 LT3150-L0 SUBJECT: NEW DRIVE AXLE
LIFT TRUCK SERIES: G35S-2 G40S-2 G45S-2 G40SC-2 G45SC-2 G50SC-2 November 15, 2000 CODE 3150 LT3150-L0 SUBJECT: NEW DRIVE AXLE A new drive axle has been introduced in the above model lift trucks. The purpose
More informationOnline version - not for reprint
(3) A Shortblock 0... B Shortblock 03, 03 L... 3 C Shortblock 0... 4 D Engine housing... D Engine housing... E Quick tensioner parts... F Oil pump... G Clutch... H Chain brake... J Muffler... K Ignition
More information