ECT SENSOR 2 2P CONNECTOR. Clamp the main wire harness and the ECT sensor 3 wire as shown.
|
|
- Dorcas Grant
- 6 years ago
- Views:
Transcription
1 CABLE/ ROUTING VIEWED FROM THE UPPER RIGHT REAR SIDE: Clamp the main wire harness and the ECT sensor 3 wire as shown. After securing the cables and harnesses with the harness band clips, cut the end of the harness band clips so that the projected length is 5 10 mm ( in) as shown. ECT SENSOR 3 WIRE Viewed from the cylinder head cover side: WATER TUBE CLAMP Set the water relief tube A in the clamp the larger diameter side and the main wire harness in the clamp the smaller diameter side. ECT SENSOR 2 2P ECT SENSOR 4 2P 5-10 mm ( in) A/F SENSOR 4P ALTERNATOR 4P ALTERNATOR B TERMINAL ECT SENSOR 1 2P ECT SENSOR 3 2P Clamp the main wire harness and the ECT sensor 3 wire as shown. ECT SENSOR 3 WIRE EOP SENSOR 3P Viewed from the cylinder head cover side: 2-17
2 VIEWED FROM THE RIGHT SIDE: ALTERNATOR B TERMINAL Install the terminal by tightening the nut, and then set the cover securely. NUT COVER Connect the cable to the alternator B terminal as shown. 60 A/F SENSOR 4P ALTERNATOR 4P ECT SENSOR 3 2P COVER LOCK CABLE 2-18
3 VIEWED FROM THE UPPER RIGHT SIDE: Clamp the main wire harness as shown. OUTSIDE A/F SENSOR 4P ECT SENSOR 2 2P ECT SENSOR 4 2P CKP SENSOR 3P ELECTRIC PARTS CASE 2-19
4 VIEWED FROM THE RIGHT SIDE: 9 10 CKP SENSOR 3P TACHOMETER PULSE CHECK 2P 11 DLC 4P 17 FUSE/RELAY JUNCTION BOX 10P 16 FUSE/RELAY JUNCTION BOX 23P NMEA P BAND CLIP 12 ECM 36P A (Gray) 15 FUSE/RELAY JUNCTION BOX 8P T6 ALTERNATOR FUSE CABLE TERMINAL 13 ECM 36P B (Black) C001 STARTER S TERMINAL T5 STARTER CABLE (+) 1 TERMINAL T4 STARTER CABLE (+) 2 TERMINAL (NOTE 1) STARTER MOTOR B TERMINAL WASHER (8 mm) NUT (8 mm) NUT (8 mm) 14 SWITCH 3P T2 STARTER CABLE (+) 2 TERMINAL T3 STARTER CABLE (+) TERMINAL STARTER MOTOR B TERMINAL NOTE 1 Harness band clip installation page
5 VIEWED FROM THE RIGHT SIDE S 10 TACHOMETER PULSE CHECK 2P 11 DLC 4P NMEA P 17 FUSE/RELAY JUNCTION BOX 10P OFFSET BAND 6 ECT SENSOR 1 2P 7 EOP SENSOR 3P 16 FUSE/RELAY JUNCTION BOX 23P 15 FUSE/RELAY JUNCTION BOX 8P S 2-21
6 FUSE/RELAY JUNCTION BOX: T6 ALTERNATOR FUSE CABLE TERMINAL GREEN TAPE STARTER MOTOR T5 STARTER CABLE (+) 1 TERMINAL YELLOW TAPE T4 STARTER CABLE (+) 2 TERMINAL RED TAPE T2 STARTER CABLE (+) 2 TERMINAL 90 C001 STARTER S TERMINAL Connect the starter cable (+) 2 terminal and the starter cable (+) terminal so that they are at a right angle to the vertical centerline as shown. T3 STARTER CABLE (+) 2-22
7 VIEWED FROM THE RIGHT FRONT SIDE Clamp the starter cable (+) 2 and power trim/tilt switch wire. SWITCH WIRE STARTER CABLE (+) 2 Clamp the starter cable (+) 1, starter cable (+) 2 and starter cable (+). STARTER CABLE (+) 1 (To fuse/relay junction box) STARTER CABLE (+) (To starter motor B terminal) Viewed from the front side: STARTER CABLE (+) 2 (To power trim/tilt relay) Viewed from the silencer case side: STARTER CABLE (+) 2 STARTER CABLES Clamp the starter cable (+) 1 and starter cable (+) 2. STARTER CABLE (+) 2 (To starter motor B terminal) GND1 STARTER CABLE GROUND TERMINAL Connect the ground terminal by pushing it against the projection on the crankcase. CABLE BRACKET A Clamp the starter cables and starter cable (+) 2. STARTER CABLE (+) 2 (To power trim/tilt relay) PROJECTION ENGINE SIDE STARTER CABLE (+) 1 (To fuse/relay junction box) Viewed from the upper side: Viewed from the front side: STARTER CABLE GROUND TERMINAL STARTER CABLES Viewed from the front side: 2-23
8 CABLE GROMMET: REMOTE CONTROL CABLE (SHIFT SIDE) REMOTE CONTROL CABLE (THROTTLE SIDE) INDICATOR WIRE CABLE GROMMET SWITCH PANEL CABLE STARTER CABLES FUEL TUBE A Viewed from the front side: 2-24
9 VIEWED FROM THE FRONT SIDE: GND2 FRAME GROUND TERMINAL (NOTE 1) GND3 FRAME GROUND TERMINAL (NOTE 1) GND4 RELAY GROUND CABLE TERMINAL (NOTE 2) 18 NEUTRAL SWITCH 2P 19 RELAY 3P 20 TP SENSOR 3P 21 WATER LEVEL SENSOR 2P CABLE BRACKET A (NOTE 3) INDICATOR WIRE 6P SWITCH PANEL CABLE 14P 24 STARTER CABLE (+) 1P TRIM ANGLE SENSOR 3P MOTOR 2P NOTE 1 Frame ground terminal installation page 2-27 NOTE 2 Power trim/tilt relay ground terminal installation page 2-27 NOTE 3 Cable bracket A (Starter cable installation) page
10 VIEWED FROM THE FRONT SIDE: REMOTE CONTROL CABLE (THROTTLE SIDE) S REMOTE CONTROL CABLE (SHIFT SIDE) COVER LOCK CABLE A REMOTE CONTROL CABLE (THROTTLE SIDE) SWITCH PANEL CABLE REMOTE CONTROL CABLE (SHIFT SIDE) INDICATOR WIRE REMOTE CONTROL CABLE GROMMET FUEL TUBE A STARTER CABLES 2-26
11 VIEWED FROM THE FRONT SIDE: FRAME GROUND CABLE TERMINALS Connect the Black, Blue, Green/Red and the Green/White wires to the upper frame ground terminal. Connect the Black/White, Blue, Green/Black and Green wires to the lower frame ground terminal. Install by pushing the frame ground cable terminals against the corresponding projections on the crankcase. PROJECTIONS GND4 RELAY GROUND CABLE TERMINAL Install by pushing the ground cable terminal against the corresponding projection on the crankcase. RELAY GROUND TERMINAL FRAME GROUND TERMINALS PROJECTION Clamp the ground cable and main wire harness. FRAME GROUND CABLE Viewed from the upper side: TRIM ANGLE SENSOR WIRE CLIP A 24 STARTER CABLE (+) 1P MOTOR WIRE 2-27
12 VIEWED FROM THE LEFT FRONT SIDE: 20 TP SENSOR 3P 21 WATER LEVEL SENSOR 2P CLIP Clamp the taped part of the water level sensor wire and main wire harness. WATER LEVEL SENSOR WIRE Viewed from the upper side: 19 RELAY 3P BAND CLIP STARTER CABLE (+) 2 MOTOR WIRE RELAY: GND4 RELAY GROUND CABLE TERMINAL (NOTE 1) TRIM ANGLE SENSOR WIRE 23 MOTOR 2P 22 TRIM ANGLE SENSOR 3P Clamp the power trim/tilt relay 3P connector wire, power trim/ tilt motor 2P connector wire and starter cable (+) 1P connector wire. (NOTE 2) 23 MOTOR 2P CLIP A 18 NEUTRAL SWITCH 2P 24 STARTER CABLE (+) 1P NOTE 1 Power trim/tilt relay ground cable terminal installation page 2-27 NOTE 2 Harness band clip installation page
13 VIEWED FROM THE LEFT FRONT SIDE: 25 IAT SENSOR 2P 26 IAC VALVE 2P 30 MAP SENSOR 3P HOLDER Clamp the main wire harness and joint connector wire as shown. JOINT WIRE Viewed from the upper side: JOINT 1 JOINT
14 VIEWED FROM THE UPPER LEFT REAR SIDE: S S JOINT S Set the joint connector to the connector holder. 28 JOINT S 29 JOINT 1 JOINT 2 ENGINE SIDE HOSE CLAMP Set the main wire harness in the smaller clamp and pressure regulator return hose in the larger clamp. ENGINE SIDE PRESSURE REGULATOR RETURN HOSE Viewed from the upper side: 2-30
15 VIEWED FROM THE LEFT REAR SIDE: KNOCK SENSOR 1P No.2 FUEL INJECTOR 2P HOSE CLAMP (NOTE 1) 41 No.1 IGNITION COIL No.1 FUEL 3P INJECTOR 2P No.2 IGNITION COIL 3P 33 No.3 IGNITION COIL 3P 38 No.3 FUEL INJECTOR 2P 37 FUEL PUMP 2P 36 No.4 FUEL INJECTOR 2P 35 CMP SENSOR 3P 34 No.4 IGNITION COIL 3P 35 CMP SENSOR 3P NOTE 1 Hose clamp installation page
16 VIEWED FROM THE LOWER LEFT SIDE: HOSE CLAMP Set the fuel hose (High pressure side) in the clamp of the larger diameter side and the main wire harness in the smaller diameter side. Clamp the fuel hose (High pressure side) to the left-hand side of the marked point. Engine side HOSE CLAMP FUEL HOSE (HIGH PRESSURE SIDE) Viewed from the throttle body side: FUEL HOSE (HIGH PRESSURE SIDE) MARKING 40 KNOCK SENSOR 1P 39 No.2 FUEL INJECTOR 2P 38 No.3 FUEL INJECTOR 2P CABLE CLIP 37 FUEL PUMP 2P COVER LOCK CABLE A COVER LOCK CABLE B 36 FUEL HOSE (HIGH PRESSURE SIDE) No.4 FUEL INJECTOR 2P 2-32
17 VIEWED FROM THE LOWER LEFT SIDE: CLIP (NOTE 1) 40 KNOCK SENSOR 1P Clamp the main wire harness and knock sensor wire. HOSE CLAMP (NOTE 2) KNOCK SENSOR WIRE Viewed from the upper side: CABLE CLIP UNDER CASE GROMMET C Clamp the power trim/tilt motor wire and trim angle sensor wire. Install under case grommet C, aligning the taped end of the power trim/tilt motor wire harness with the end of under case grommet C. Check that the wires are not interfering with the front lock of the under cover front bracket. SPIRAL TUBE Wind the spiral tube around the power trim/tilt motor wire harness and trim angle sensor wire. WIRE CLIP (NOTE 3) FRONT LOCK Wires and tube are not interfering with the front lock. UNDER CASE GROMMET C Taped end TRIM ANGLE SENSOR WIRE MOTOR WIRE NOTE 1 Harness clip installation page 2-28 NOTE 2 Hose clamp installation page 2-32 NOTE 3 Wire harness clip installation page
18 SWIVEL CASE: CLIP Align the tape end of the power trim/tilt motor wire harness with the clip end. TAPE END CLIP Clamp the spiral tube as shown. SPIRAL TUBE CLIP END Viewed from the lower side: Viewed from the left side: MOTOR WIRE SPIRAL TUBE TRIM ANGLE SENSOR WIRE MOTOR WIRE GROUND CABLE Viewed from the cylinder head side: POWER TRIM/ TILT MOTOR WIRE TRIM ANGLE SENSOR WIRE SPEED SENSOR TUBE WIRE CLIP MOTOR WIRE Clamp the spiral tube as shown. MOTOR CORD BUSHING Align the tape end of the power trim/tilt motor wire harness with the clip end. POWER TRIM/ TILT MOTOR WIRE SPIRAL TUBE CLIP TAPE END BUSHING END Viewed from the left side: Viewed from the cylinder head side: Viewed from the right side: TRIM ANGLE SENSOR WIRE 2-34
2-17 CABLE/HARNESS ROUTING SERVICE INFORMATION 1 IAC VALVE 2P CONNECTOR. 11 No.1 INJECTOR 2 TP SENSOR 3P CONNECTOR 2P CONNECTOR
CABLE/ ROUTING SERVICE INFORMATION 11 No.1 INJECTOR 2P 15 IAB CONTROL SOLENOID VALVE 2P 1 IAC VALVE 2P 2 TP SENSOR 3P JUNCTION (24P) MAIN WIRE to SWITCH WIRE 6P 16 CMP SENSOR 1 CMP SENSOR 2 4P 14 EBT SENSOR
More informationE50PL4SSC 4-Stroke, Elec Start, TNT, 20 IN. shaft 2000 : CAMSHAFT & TIMING [1/21] Page 1 of 44
E50PL4SSC 4-Stroke, Elec Start, TNT, 20 IN. shaft 2000 : CAMSHAFT & TIMING [1/21] Page 1 of 44 E50PL4SSC 4-Stroke, Elec Start, TNT, 20 IN. shaft 2000 : CAMSHAFT & TIMING [1/21] 1 5031326 1 CAMSHAFT, Intake
More information5-2 TOOLS FUEL SYSTEM. Fuel pressure gauge PSI B. SCS short connector 070PZ-ZY Float level gauge
FUEL SYSTEM TOOLS SCS short connector 070PZ-ZY30100 Float level gauge 07401-0010000 Fuel pressure gauge 0 100 PSI 07406-004000B Fuel pressure hose 07406-004020B Tester probe (male) 07ZAJ-RDJA110 5-2 SERVICE
More informationLSx Harness Installation. lsxeverything.com #BecauseYouShould
LSx Harness Installation lsxeverything.com #BecauseYouShould Table of Contents Slide 1 Introduction Page Slide 2 Table of Contents Slide 3 Starting Instructions Slide 4 Power Connections Slide 5 Ground
More information18. IGNITION SYSTEM 18-1 SYSTEM DIAGRAM 18-2 IGNITION SYSTEM INSPECTION 18-5 SERVICE INFORMATION 18-3 IGNITION COIL 18-8 TROUBLESHOOTING 18-4
18. IGNITION SYSTEM SYSTEM DIAGRAM 18-2 SERVICE INFORMATION 18-3 TROUBLESHOOTING 18-4 IGNITION SYSTEM INSPECTION 18-5 IGNITION COIL 18-8 IGNITION TIMING 18-8 18 18-1 IGNITION SYSTEM SYSTEM DIAGRAM IGNITION
More informationE70PL4EEC 1999 : CAMSHAFT [1/23] Page 1 of 49
E70PL4EEC 1999 : CAMSHAFT [1/23] Page 1 of 49 E70PL4EEC 1999 : CAMSHAFT [1/23] 1 5030657 1 CAMSHAFT 2 5030658 1 PLATE, Camshaft thrust 3 5030549 1 SEAL, Camshaft 4 5030989 2 BOLT, Plate 5 5030663 8 ARM,
More informationTelephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: Name: Manufacturer: Ford Address: Model: Year: 1994 Registration: Tel - Private: Tel - Business: Mileage: Job number: Terminal side Wire side Component/circuit description
More informationDownload Service & repair manual Yamaha F250, LF PDF Service Manual
Download Service & repair manual Yamaha F250, LF250 2006 - PDF Service Manual DOWNLOAD HERE "Download Service & repair manual Yamaha F250, LF250 2006 - PDF Service Manual Do you want to service & repair
More informationTelephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: Terminal side Wire side Component/circuit description ECM pin Signal Condition Typical value Oscilloscope setting (Suggested settings - Voltage/time per division)
More information7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).
1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual
More informationTelephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: K143 AC compressor clutch relay X88 AC connector S63 AC refrigerant pressure switch S341 AC refrigerant triple pressure switch A16 Anti-lock braking system (ABS) control
More informationGL1800 FI "Fault Indicator" Dashboard Codes
GL1800 FI "Fault Indicator" Dashboard Codes If FI (Fault Indicator) light comes on pull over but DO NOT shut bike off. Put in neutral and put side stand down, RPM s below 1500. This signals the ECM to
More information19. IGNITION SYSTEM 19-1 SYSTEM DIAGRAM 19-2 IGNITION SYSTEM INSPECTION 19-5 SERVICE INFORMATION 19-3 CKP SENSOR 19-7 TROUBLESHOOTING 19-4
19. IGNITION SYSTEM SYSTEM DIAGRAM 19-2 SERVICE INFORMATION 19-3 TROUBLESHOOTING 19-4 IGNITION SYSTEM INSPECTION 19-5 CKP SENSOR 19-7 IGNITION TIMING 19-8 19 19-1 IGNITION SYSTEM IGNITION SYSTEM SYSTEM
More informationManual P/N Copyright Third Edition June 21, 2005
P/N 60212, 60213, 60214 & 60215 1996-99 GM VORTEC WIRE HARNESS INSTALLATION INSTRUCTIONS Manual P/N 90524 Copyright 2003 Third Edition June 21, 2005 PAINLESS PERFORMANCE PRODUCTS 2501 Ludelle Street, Fort
More informationSUM EFI Wiring Harness for GM LT-1/LT-4 Engine INSTALLATION INSTRUCTIONS
SUM-890121 EFI Wiring Harness for GM LT-1/LT-4 Engine INSTALLATION INSTRUCTIONS INTRODUCTION This harness is designed for GM 1992-97 LT1/LT4 fuel injected engines. Even with minimal electrical experience,
More informationVOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ
VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ Telephone: 01752 667007 Fax: 01752 663399 Email: mail@volkscity.com 1 Camshaft position (CMP) sensor 1 2 Camshaft position (CMP) sensor 2 3 Camshaft position
More information75/90 FOURSTROKE EFI WIRING DIAGRAM
75/0 FOURSTROKE EFI WIRING DIAGRAM 0-87725 MARCH 2005 Page 8A-3 75/0 FourStroke EFI Wiring Diagram - Electronic control module (ECM) 2 - Engine water temperature sensor 3 - Ignition coil for cylinder #
More informationTroubleshooting Self-diagnostic Procedures
Self-diagnostic Procedures I. When the Malfunction Indicator Lamp (MIL) has been reported on, do the following: 1. Connect the Service Check Connector terminals with a jumper wire as shown. (The 2P Service
More informationP/N & GM LS1 FUEL INJECTION WIRE P/N & GM LS1 FUEL INJECTION WIRE HARNESS INSTALLATION INSTRUCTIONS
P/N 60506 & 60507 1997-98 GM LS1 FUEL INJECTION WIRE HARNESS INSTALLATION INSTRUCTIONS P/N 60508 & 60509 1999-0 GM LS1 FUEL INJECTION WIRE HARNESS INSTALLATION INSTRUCTIONS Manual P/N 9050 Seventh Edition
More informationP/N & GM LS1 w/mechanical (cable) THROTTLE BODY FUEL INJECTION WIRE HARNESS INSTALLATION INSTRUCTIONS
P/N 60508 & 60509 1997-0 GM LS1 w/mechanical (cable) THROTTLE BODY FUEL INJECTION WIRE HARNESS INSTALLATION INSTRUCTIONS Manual P/N 9050 Painless Performance Products, LLC 501 Ludelle Street Fort Worth,
More informationA: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES. Signal (V) Ignition SW ON (Engine OFF) B B B
5. Specified Data A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen heater Engine coolant temperature Signal
More informationP/N GM VORTEC THROTTLE BY WIRE FUEL INJECTION 4.8L, 5.3L & 6.0L WIRE HARNESS INSTALLATION INSTRUCTIONS
P/N 60221 2003-2006 GM VORTEC THROTTLE BY WIRE FUEL INJECTION 4.8L, 5.3L & 6.0L WIRE HARNESS INSTALLATION INSTRUCTIONS Manual P/N 90570 FIRST EDITION September 2009 Copyright SEPTEMBER 2009 PAINLESS PERFORMANCE
More informationEngine management/transmission
MAZDA Model: 323 (BG) 323 Estate 1,6/4x4 (BW) 323 (BA/BJ) 626/MX-6 626/Estate Xedos 6/9 MX-3/MX-5 Year: 1989-00 Engina code: BP, BP-DOHC, B3, B3E, B6, B6-SOHC, B6-DOHC, B6E,FP, FS, KF, KJ, KL K8, RF, RF-CX,
More informationFor Troubleshooting of DTC related components, see chart on page INTAKE AIR BYPASS (IAB) HIGH CONTROL SOLENOID
Index For Troubleshooting of DTC related components, see chart on page 11-53. '96-99 models: EXHAUST GAS RECIRCULATION (EGR) and LIFT MANIFOLD ABSOLUTE PRESSURE (MAP) INTAKE AIR BYPASS (IAB) HIGH page
More informationP/N & /1995 GM LT1 FUEL INJECTION WIRE HARNESS INSTALLATION INSTRUCTIONS
P/N 60502 & 60505 1994/1995 GM LT1 FUEL INJECTION WIRE HARNESS INSTALLATION INSTRUCTIONS Manual P/N 90517 Copyright May 2002 PAINLESS PERFORMANCE PRODUCTS 2501 Ludelle Street - Fort Worth, Texas 76105-1036
More informationTELORVEK II RJ-32 Big Block RamJet Fuel Injection System
Page #1 TELORVEK II RJ-32 Big Block RamJet Fuel Injection System This wiring system is compatible with the GM Performance part big block Ramjet 502 engine. The harness is designed to dress up the appearance
More informationP/N & GM VORTEC FUEL INJECTION 4.8L, 5.3L & 6.0L WIRE HARNESS INSTALLATION INSTRUCTIONS
P/N 6017 & 6018 1999-00 GM VORTEC FUEL INJECTION 4.8L, 5.3L & 6.0L WIRE HARNESS INSTALLATION INSTRUCTIONS Manual P/N 90530 Second Edition November 004 Copyright November 004 PAINLESS PERFORMANCE PRODUCTS
More informationPGM-FI ( Models)
PGM-FI ( 00-0 Models) HOT AT ALL TIMES HOT IN ON OR START FUSE BACK UP, (RADIO).5A FUSE FI E/M 5A C PHOTO UNDER- HOOD FUSE/ RELAY PHOTO FUSE FUEL PUMP (SRS UNIT) 5A page 0-. UNDER- DASH FUSE/ RELAY PHOTO
More informationMiata - Workshop Manual - Engine
Page 1 of 8 2003 - Miata - Workshop Manual - Engine NO.6 CRANKS NORMALLY BUT WILL NOT START 6 Cranks normally but will not start Starter cranks engine at normal speed but engine will not run. DESCRIPTION
More informationVortec Drive by Cable Electronic Fuel Injection Wiring Harness (P/N HAR-1018) HAR-1018
1998 2002 Vortec Drive by Cable Electronic Fuel Injection Wiring Harness (P/N HAR-1018) HAR-1018 PERFORMANCE SYSTEMS INTEGRATION 170 Oberlin Ave N Suite 13 Lakewood NJ 08701-4548 Ph: 732-444-3277 Email:
More informationService Bulletin. Applies To: MDX ALL 2006 MDX From VIN 2HNYD18..6H thru 2HNYD18..6H535538
Service Bulletin Applies To: 2003 05 MDX ALL 2006 MDX From VIN 2HNYD18..6H500001 thru 2HNYD18..6H535538 06-028 July 13, 2007 MIL Comes On With DTC P0335, P0339, P0385, or P0389, and the Engine Runs Roughly
More informationTELORVEK EFI a l Fue l In. n MK-93A
Page #1 TELORVEK EFI 4.6Se q uen i t a l Fue l In j e cti o n S ystem MK-93A WIRING INSTRUCTIONS Thank you for purchasing the absolute finest of wiring kits for the Ford Motor Co. 4.6 MARK VIII fuel injection
More information2002 ENGINE PERFORMANCE. Self-Diagnostics - RAV4. Before performing testing procedures, check for any related Technical Service Bulletins (TSBs).
2002 ENGINE PERFORMANCE Self-Diagnostics - RAV4 INTRODUCTION NOTE: Before performing testing procedures, check for any related Technical Service Bulletins (TSBs). To properly diagnosis and repair this
More information'05- 'Current LS2/LS3 Drive by Cable Electronic Fuel Injection Wiring Harness HAR-1058
'05- 'Current LS2/LS3 Drive by Cable Electronic Fuel Injection Wiring Harness HAR-1058 PERFORMANCE SYSTEMS INTEGRATION 170 Oberlin Ave N Suite 13 Lakewood NJ 08701-4548 Ph: 732-444-3277 Email: INFO@PSIConversion.com
More informationhttp://www.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=t... Page of // 0 Chevrolet Traverse.L Eng LT Service Manual: WIRING DIAGRAMS Print Date: // ENGINE PERFORMANCE >.L VIN D Fig
More information1. Connect the Honda PGM Tester or an OBD II scan tool to the 16P Data Link Connector (DLC) located behind the right side of the center console.
Troubleshooting Procedures I. How To Begin Troubleshooting When the Malfunction indicator Lamp (MIL) has been reported on, or there is a driveability problem, use the appropriate procedure below to diagnose
More information2UZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM
385 P2237 / Open (Bank 1 Sensor 1) P2238 Low (Bank 1 Sensor 1) P2239 High (Bank 1 Sensor 1) P2240 P2241 / Open (Bank 2 Sensor 1) Low (Bank 2 Sensor 1) P2242 High (Bank 2 Sensor 1) P2252 Low (Bank 1 Sensor
More information5. Engine Control Module (ECM) I/O Signal S008526
5. Engine Control Module (ECM) I/O Signal S008526 A: ELECTRICAL SPECIFICATION S008526A08 1. MT VEHICLES S008526A0801 B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen
More informationhttp://www.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=tr... Page of //0 00 Chevrolet Silverado.L Eng 00 Service Manual: WIRING DIAGRAMS - 00 Print Date: //0 ENGINE PERFORMANCE Tip:
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More informationAudi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly
Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie
More informationSUM EFI Wiring Harness for GM LS1 Engine INSTALLATION INSTRUCTIONS
SUM-890122 EFI Wiring Harness for GM LS1 Engine INSTALLATION INSTRUCTIONS 1 INTRODUCTION This harness is designed for GM 1997-2002 LS1 fuel injected engines utilizing a mechanical throttle body and throttle
More informationTELORVEK EFI 4.6 Sequential Fuel Injection System (MG-91A)
Page #1 TELORVEK EFI 4.6 Sequential Fuel Injection System (MG-91A) WIRING INSTRUCTIONS Thank you for purchasing the absolute finest of wiring kits for the 1996-98 Ford Motor Co. 4.6 / COBRA fuel injection
More informationDTC Summaries. NipponDenso V12 Engine Management
DTC Summaries NipponDenso V12 Engine Management OBD II MONITORING CONDITIONS: When testing for DTC reoccurrence, it can be determined if the Service Drive Cycle was of sufficient length by performing a
More informationP/N & GM LS1 FUEL INJECTION WIRE HARNESS INSTALLATION INSTRUCTIONS
P/N 605 & 6053 00-04 GM LS1 FUEL INJECTION WIRE HARNESS INSTALLATION INSTRUCTIONS Manual P/N 90544 nd Edition July 014 PAINLESS PERFORMANCE PRODUCTS 501 Ludelle Street - Fort Worth, Texas 76105-1036 -
More informationThis is the layout of a typical harness form a TPI Camaro.
TPI wiring harness, typical 1986-89: This is the layout of a typical harness form a 1986-88 TPI Camaro. (A) bulkhead conn. through firewall. (B) ecm conn. (C) jct. conn for fuel injectors and cooling fan.
More informationSYSTEM & COMPONENT TESTING
SYSTEM & COMPONENT TESTING 2001 Chevrolet Camaro 2001 ENGINE PERFORMANCE System & Component Testing - Cars Except Metro & Prizm MODEL IDENTIFICATION Vehicle model is identified by fourth character of Vehicle
More informationTelephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: Terminal side Wire side Component/circuit description ECM pin Signal Condition Typical value Oscilloscope setting (Suggested settings - Voltage/time per division)
More informationMegaSquirt III for Gen 3 HEMI. Hardware Install THE FOLLOWING SENSOR PART NUMBERS APPLY TO ALL HARNESSES FOR ENGINES 2004 TO CURRENT:
MegaSquirt III for Gen 3 HEMI MegaSquirt controllers are experimental devices intended for educational purposes. MegaSquirt controllers are not for sale or use on pollution controlled vehicles. Check the
More informationMegaSquirt III for LS Style Engines. Hardware Install. 1. Disconnect and remove the battery from the vehicle.
MegaSquirt III for LS Style Engines MegaSquirt controllers are experimental devices intended for educational purposes. MegaSquirt controllers are not for sale or use on pollution controlled vehicles. Check
More informationBASIC DIAGNOSTIC PROCEDURES
BASIC DIAGNOSTIC PROCEDURES 2001 Chevrolet Camaro 2001 ENGINE PERFORMANCE Basic Diagnostic Procedures - Cars Except Metro & Prizm MODEL IDENTIFICATION MODEL IDENTIFICATION Body Code (1) Model C... Park
More informationELECTRICAL WIRING DIAGRAMS
SECTION 5 ELECTRICAL WIRING DIAGRAMS CONTENTS. ARTING & CHAING CIRCUIT... 5-8 ) GSL E M A/T... 5-8 ) GSL TRE A/T, GSL E M A/T...5-0 ) DSL NA TRE A/T, M/T... 5- ) DSL LA TRE A/T, M/T... 5-. PREHEAT'G UNIT
More informationDIFFERENCE BETWEEN LT-A750XK8 AND LT-A750XL1
PAGE: 1 OF 5 SUBJECT: NOTICE OF SET-UP MANUAL APPLICABLE MODEL: LT-A750XL1 EFFECTIVE ENGINE OR FRAME NO.: REFERENCE: This bulletin is to inform you of set-up procedures of LT-A750XL1. Please inform your
More informationTruck and Transport IP Red Seal Practice Exam PRACTICE EXAM 4
Truck and Transport IP Red Seal Practice Exam PRACTICE EXAM 4 1. Which of these sensors directly measures engine load? a. Manifold absolute pressure sensor. b. Coolant sensor (ECT). c. Vehicle speed sensor.
More informationTELORVEK EFI. 4.6 Sequential Fuel Injection System (FT-95) WIRING INSTRUCTIONS
Page #1 TELORVEK EFI 4.6 Sequential Fuel Injection System (FT-95) WIRING INSTRUCTIONS Thank you for purchasing the absolute finest of wiring kits for the Ford Motor Co. 4.6 94-95 Thunderbird, Cougar fuel
More informationTelephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: Name: Manufacturer: Ford Address: Model: Scorpio Year: 1991 Registration: Tel - Private: Tel - Business: Mileage: Job number: Terminal side Wire side Component/circuit
More informationJACKAROO TIPS Understanding the MIL fault codes on a Jackaroo Turbo Diesel
JACKAROO TIPS Understanding the MIL fault codes on a Jackaroo Turbo Diesel The Jackaroo, as with all vehicles intended to be supplied to the USA market, (as the Isuzu Trooper) is fitted with OnBoard Diagnostics
More informationMotronic injection system,
Page 1 of 78 24-1 Motronic injection system, servicing Safety precautions If special testing equipment is required during road test, note the following: WARNING! Scan tools and testing devices must always
More informationTELORVEK EFI 4.6 Sequential Fuel Injection System MK-93
Page #1 TELORVEK EFI 4.6 Sequential Fuel Injection System MK-93 WIRING INSTRUCTIONS Thank you for purchasing the absolute finest of wiring kits for the Ford Motor Co. 4.6 MARK VIII fuel injection engine.
More information20. ELECTRIC STARTER 20-1 SYSTEM DIAGRAM 20-2 STARTER MOTOR 20-6 SERVICE INFORMATION 20-3 STARTER RELAY SWITCH TROUBLESHOOTING 20-4 DIODE 20-15
20. SYSTEM DIAGRAM 20-2 SERVICE INFORMATION 20-3 TROUBLESHOOTING 20-4 STARTER MOTOR 20-6 STARTER RELAY SWITCH 20-13 DIODE 20-15 20 20-1 SYSTEM DIAGRAM IGNITION SWITCH ENGINE STOP SWITCH CLUTCH SWITCH STARTER
More informationELECTRICAL SYSTEMS 4 D WIRING DIAGRAMS
EECTRICA SYSTEMS 4 D WIRING DIAGRAMS Table of Contents Page Wiring Colors for MerCruiser............... 4D- Wire Color Abbreviations............... 4D- Wiring Diagrams......................... 4D- MCM./.X......................
More informationVCM CONNECTOR TERMINAL IDENTIFICATION
Page 1 of 5 Service Manual: VCM CONNECTOR TERMINAL IDENTIFICATION VCM CONNECTOR TERMINAL IDENTIFICATION 1999 Chevrolet Tahoe 5.7L Eng Fig 1: Identifying Control Module Harness Connector Terminals (4.3L,
More informationPrins autogassystemen b.v. Veldhoven
Prins autogassystemen b.v. Veldhoven MOUNTING INSTRUCTION ENGINE CONVERSION SET MAKE OF AUTOMOBILE: TYPE: ASTRA PISTON DISPLACEMENT: 2000 cc MT NUMBER OF VALVES: 16V ENGINE NUMBER: X20XEV INJECTION SYSTEM:
More informationCylinder Head Replacement
CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A
More informationIntake Manifold Replacement
Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:
More informationG - TESTS W/CODES - 2.2L
G - TESTS W/CODES - 2.2L 1994 Toyota Celica 1994 ENGINE PERFORMANCE Toyota 2.2L Self-Diagnostics Celica INTRODUCTION If no faults were found while performing F - BASIC TESTING, proceed with self-diagnostics.
More informationCA 421 Installation Instructions
CA 421 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More informationGM VORTEC Drive by Wire Electronic Fuel Injection Wiring Harness HAR-1014
GM VORTEC Drive by Wire Electronic Fuel Injection Wiring Harness HAR-1014 PERFORMANCE SYSTEMS INTEGRATION 170 Oberlin Ave N Suite 13 Lakewood NJ 08701-4548 Ph: 732-444-3277 Email: INFO@PSIConversion.com
More informationP/N & GM LS2 FUEL INJECTION WIRE HARNESS INSTALLATION INSTRUCTIONS. Manual P/N 90543
P/N 6050 & 6051 005-06 GM LS FUEL INJECTION WIRE HARNESS INSTALLATION INSTRUCTIONS Manual P/N 90543 1 Painless Performance Products, LLC 501 Ludelle Street Fort Worth, TX 76105-1036 800-43-9696 phone 817-44-404
More informationPGM-FI (All Models except D16B5; D16Y5 with M/T)
PGM-FI (All 9-9 Models except DB; 99-00 DY with M/T) HOT AT ALL TIMES HOT IN ON OR START / FUSE 7 BACK UP 7.A page 0-. 7 / FUSE FI E/M A C PHOTO VIEW UNDER-HOOD FUSE/RELAY PHOTO 7 / FUSE FUEL PUMP (SRS
More informationPERFORMANCE SYSTEMS INTEGRATION
2006 Current GEN IV LSX/Vortec 4.8, 5.3, 6.0, 6.2, 7.0 Drive by Wire (58X) Electronic Fuel Injection Wiring Harness w/ Manual or Non- Electronic Automatic Transmission HAR-10 (See Below) (P/N HAR- 1035,
More information20-pin ECU Technical Specs. Engine Control Unit. (ECU) Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED
Engine Control Unit (ECU) Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Product: Part#:
More information9.6 ME-SFI (ME1.0) Engine 120
Components on engine Model 129 Figure 1 B2/6 Left hot film MAF sensor (located on right side of engine) B2/7 Right hot film MAF sensor (located on left side of engine) B17/5 Left IAT sensor (located in
More informationMARINE ILLUSTRATED PARTS MANUAL MODEL MP6.0L
MARINE ILLUSTRATED PARTS MANUAL MODEL MP6.0L L510014 12/02 This Page Was Intentially Left Blank MODEL MP6.0L PARTS MANUAL - 1 Contents: Symbols... 2 Maintenance Item Part Numbers... 3 Cylinder Block Assembly
More informationVORTEC Drive by Wire Electronic Fuel Injection Wiring Harness HAR-1085
2001 2002 VORTEC Drive by Wire Electronic Fuel Injection Wiring Harness HAR-1085 PERFORMANCE SYSTEMS INTEGRATION 170 Oberlin Ave N Suite 13 Lakewood NJ 08701-4548 Ph: 732-444-3277 Email: INFO@PSIConversion.com
More information9/9/2014 F15MSHC 2004 / TOP COWLING Yamaha Motor Corporation, U.S.A. All rights reserved.
F5MSHC 00 Page of 6 9/9/0 F5MSHC 00 / TOP COWLING 0 Yamaha Motor Corporation, U.S.A. All rights reserved. F5MSHC 00 Page of 6 9/9/0 Part List F5MSHC 00 / TOP COWLING REF - NO PART NUMBER PART NAME QUANTITY
More informationEngine Cranks But Does Not Run
Page 1 of 5 2000 GMC Truck GMC K Sierra - 4WD Sierra, Silverado, Suburban, Tahoe, Yukon (VIN C/K) Service Manual Engine Engine Controls - 4.8L, 5.3L, and 6.0L Diagnostic Information and Procedures Engine
More informationEngine Control Unit. (ECU) Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED
Engine Control Unit (ECU) Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Product: Type:
More information12/24/2017 Engine Controls (Powertrain Management) - ALLDATA
//0 Engine Controls (Powertrain Management) - ALLDATA 00 Dodge or Ram Truck Caravan V-.L VIN R Vehicle > Powertrain Management > Diagrams > Electrical - Interactive Color (Non OE) Engine Controls - Page
More informationINTERFACE PART NUMBER NOTES
2004 Pontiac GTO ALARM REMOTE START WIRING WIRE COLOR LOCATION 12V CONSTANT WIRE Must go to battery for 12V Battery STARTER WIRE PURPLE Ignition harness IGNITION WIRE ORANGE Ignition harness ACCESSORY
More information1991 Turbo Automatic. Pin # Pin #
1991 Turbo Automatic Pin # 1 2 3 4 5 90980 10988 90980 10987 6 B1 Pin # 1 2 3 C1 Batt M-Rel Alarm Horn Power from EFI Main Relay to VSV's;IACV;O2;+B;+B1;O2;Diag;Circuit Opening Relay Black/Yellow Black/Orange
More information3/14/2018 Engine Controls (Powertrain Management) - ALLDATA
//0 Engine Controls (Powertrain Management) - ALLDATA 00 Chrysler Truck PT Cruiser L-.L VIN X Vehicle > Powertrain Management > Diagrams > Electrical - Interactive Color (Non OE) Engine Controls - Page
More information1996 Mustang. 1. Remove air cleaner outlet tube (9B659). Refer to Section Disconnect battery ground cable (14301). Refer to Section
REMOVAL AND INSTALLATION Fuel Charging Wiring Removal and Installation 1. Remove air cleaner outlet tube (9B659). Refer to Section 03-12. 2. Disconnect battery ground cable (14301). Refer to Section 14-01.
More informationFuel System (Central SFI)
Page 1 of 6 1997 GMC Truck GMC K Pickup - 4WD Chevy Pickup, GMC Pickup, Suburban, Tahoe, Yukon (VIN C/K) Service Manual Engine Engine Controls - 5.0L, 5.7L, and 7.4L Description and Operation Document
More informationCopyright Triple S Customs
CADILLAC CONCOURS 1994-1997 VEHICLE WIRING Copyright 2002-2004 Triple S Customs WIRING INFORMATION: 1994 Cadillac Concours 12V CONSTANT WIRE RED Ignition Harness STARTER WIRE YELLOW Ignition Harness IGNITION
More informationPage 1 of 8 SECTION 303-01A: Engine 2.3L 2002 Ranger Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/20/2004 Intake Manifold Removal 1. Remove the accelerator control snow shield. 2. Remove
More informationFuel control. The fuel injection system tasks. Starting fuel pump (FP)
1 Fuel control The fuel injection system tasks - To provide fuel - To distribute the fuel between the cylinders - To provide the correct quantity of fuel Starting fuel pump (FP) The control module (1)
More informationAudi A4 Current Flow Diagram No. 44 / 1 Edition
Page 1 of 16 Audi A4 Current Flow Diagram No. 44 / 1 Edition 05.2003 1.8 l - Fuel injection engine (110 kw - Motronic - 4 cylinder), engine code AVJ from model year 2002 1.8 l - Fuel injection engine (120
More information01 02B ON-BOARD DIAGNOSTIC [ENGINE CONTROL SYSTEM (FS)]
ON-BOARD DIAGNOSTIC [ENGINE CONTROL SYSTEM (FS)] CONTROL SYSTEM WIRING DIAGRAM [FS]............................ 2 CONTROL SYSTEM DEVICE AND CONTROL RELATIONSHIP CHART [FS]........ 4 Engine Control System............
More informationAuto Diagnosis Test #7 Review
Auto Diagnosis Test #7 Review Your own hand written notes may be used for the 1 st 10 minutes of the test Based on Chapters 25, 26, 32, 33, 34 and Lab Demonstrations Auto Diagnosis Test #7 Review Your
More informationOil trap electrically heated, replacing
1(5) Oil trap electrically heated, replacing Removing Note! As the illustrations in the information are used for different model years and/or models, some variation may occur. However, the essential information
More informationDesigned for the Street Proven on the Track
TDR Fuel and Timing Card Wiring Thank you for using our TDR Fuel and or Timing Cards (F/T). There are two options on how to wire the F/T cards. Our preferred method is to use our TDR Patch Harness as shown
More information40VEO 03(63C2) 50HETO 03(62X4) 50HEDO 03(62X5) 50HMHO 03(63G2) 1B62X 664E1
40V 03(63C2) 50H 03(62X4) 50H 03(62X5) 50H 03(63G2) 1B62X 664E1 FOREWORD This Parts Catalogue is related to the parts for the model(s) in the below frame. When you are ordering replacement parts, please
More informationDISASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
More informationTELORVEK EFI. 4S. S e. n s tem. a l Fue l I n j e cti
Page #1 4.63 V &5 TELORVEK EFI. 4S /C S e q uen i t a l Fue l I n j e cti o n Sy s tem MG-05 / MG-05A WIRING INSTRUCTIONS Thank you for purchasing the absolute finest of wiring kits for the Ford Motor
More informationTO INDEX IGNITION SYSTEM
TO INDEX IGNITION SYSTEM IG IGNITION SYSTEM CIRCUIT... IG 2 SPARK TEST... IG 4 SPARK PLUG... IG 4 POWER SUPPLY... IG 5 CRANK ANGLE SENSOR... IG 7 CAM ANGLE SENSOR... IG 8 EFI ECU... IG 8 IGNITION TIMING...
More informationDiagnostic Trouble Code (DTC) Root Cause. for Omnitek ECM 64A/66A/88A. & Remedial Action
Diagnostic Trouble Code (DTC) Root Cause & Remedial Action for Omnitek ECM 64A/66A/88A Omnitek Engineering Corp. 1945 S Rancho Santa Fe Rd. San Marcos, CA 92078 Tel. 760-591-0089 - Fax. 760-591-0880 -
More informationELEC ELECTRICAL SIGNAL SYSTEM CIRCUIT DIAGRAM SIGNAL SYSTEM EB806000
EB806000 SIGNAL SYSTEM CIRCUIT DIAGRAM TRICAL 26 3 Main switch 4 Battery 6 Fuse (main) 35 Flasher relay 40 Turn switch 4 Hazard switch 42 Front turn signal light 43 Rear turn signal light 52 Fuse (signal)
More informationMARINE ILLUSTRATED PARTS MANUAL
MARINE ILLUSTRATED PARTS MANUAL MODEL MP6.0L MY 2003-2004 09/04 This Page Was Intentially Left Blank MODEL MP6.0L PARTS MANUAL - Contents: Symbols... 2 Maintenance Item Part Numbers... 3 Cylinder Block
More informationservice bulletin MCM 454 Magnum EFI, MIE 454 EFI Ski GM Gen V Engine Specifications No Magnum 454 EFI Model EFI Ski (Average Octane Rating)
service bulletin TO: SERVICE MANAGER MECHANICS PARTS MANAGER No. 93-25 MCM 454 Magnum EFI, MIE 454 EFI Ski GM Gen V Engine Specifications NOTE: Generation V Engines Have the Fuel Pump Mounted on the Belt
More information