univex INSTRUCTION MANUAL Meat Grinder PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor

Size: px

Start display at page:

Download "univex INSTRUCTION MANUAL Meat Grinder PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor"

Camron Cain
6 years ago
Views:

1 NSTRUCTON MANUAL Meat Grinder Persons under age 18 are not permitted to operate or have accessibility to operate this equipment per U.S. Dept. of Labor Employment Standards Administration Fact Sheet No. ESA91-3. univex MG22/0603 ED 3

2 TO NSURE BOTH SAFE AND TROUBLEFREE PERFORMANCE WE STRESS THAT ALL PERSONNEL THAT WLL BE NVOLVED WiTH YOUR NEW UNVEX MEAT GRNDER MUST READ AND UNDERSTAND THESE NSTRUCTONS BEFORE ATTEMPTNG TO OPERATE THS UNT. WE APPRECATE YOUR COOPERATON AND YOUR BUSNESS. SHOULD THERE BE A QUESTON OR F WE CAN BE OF FURTHER ASSSTANCE, PLEASE CALL US, 6O

3 MG22 DESCRPTON TABLE OF CONTENTS PAGE Table of Contents Operator Safety nstallation 2 Assembly and Operating nstructions 2-3 Cleaning 3 Parts List 4-5 Assembly 6 Wiring Diagram 115/ V, 60HZ, PH / V, 50HZ, PH 7 Wiring Diagram, Canada, CE, 115/ V, 60HZ, PH / 230V,50HZ, PH 8 Warranty nformation Back Cover MG22 MEAT GRNDER NSTRUCTON MANUAL nspection: All Univex MG22's are inspected prior to packaging to assure both the machine quality, correct inclusion of options, and proper voltage. However, upon unpacking, all items should be carefully verified that they are correct, Any damage, imperfection, or shortages should be reported immediately to your dealer or directly to Univex Customer Service, and/or shipment carrier. Operator Safety: t is a violation of the United States Department of Labor regulations to permit operation of the MG22 by any person under the age of 18 years. Read and understand all instructions and safety warnings prior to operating unit. Never put fingers or any utensils (other than the stomper (tem 10) in the throat or entry of the grinder, or in the kniíb and plate area of the grinder. This is a powerthl unit designed to grind meat; use extreme caution and avoid exposing body parts to grinding and cutting areas of the unit. Switch the power off and disconnect the electric power supply prior to mounting and dismounting the grinder, cleaning, or servicing. Knife is sharp and can cut finger. Use caution when handling. Always have chopper securely mounted, worm assembly fully coupled onto drive coupling, and the knife, plate, and ring snugged on before switching the power on. Always remove the grinder from the power drive before cleaning; never rinse with hose while mounted to power source, inviting electrical shock. Page 1

4 MG22 nstallation; This is a table-top unit. Unit may be secured to table top via the shipping bolt threaded holes on the power drive housing bottom. nsure the unit is located such that it is placed on a level and stable surfàce, and sufficient clearance is provided all around the unit for safrty and ease of operation. Proper location includes space for the feed pan and clip-on storage container, Feed pan support bracket (tem 45) must be assembled onto the housing cover (tem 43) using the screws (tem 46) provided. ntroduction: ASSEMBLY AND OPERATNG NSTRUCTONS; The Univex MG22 Meat Grinder consists of a H.P. electric motor power base which drives a bell-shaped meat grinder designed to utilize industry standard #22 knives and full range of #22 grinding plates. ncluded as standard equipment is a carbon steel knife (tem 3), 3/16 grinding plate (tem 2), aluminum meat stomper (tem 10), 16 x 24 aluminum feed pan (tem 9) for holding meat to be processed, and t8.5 x 13.5 storage container with lid för collecting meat as it is processed. The Univex MG22 has safety and ease of operation built into it. The permanent safety guard positioned over the bell-shaped feed hopper prevents accidental entry of operator's fingers and hands into the grinding zone, The readily removable feed pan and storage container provide for ease of processing and cleaning. Noise emissions below 70 db(a). Assembly: WARNNG: Disconnect power supply prior to assembly. Mount the housing-guard assembly (tem 8) to the housing weldment (tem 26) by firmly tightening knobs (tem 12) onto mounting studs (tem 14). Slide the worm assembly (tems 6,5,4) into the housing-guard assembly (tem 8) and mating into the drive coupling (tem 15). Slide the knife (tem 3), sharp edges toward the plate, onto the square of the worm assembly (tem 4). Slide the plate (tem 2) onto the worm assembly (tem 4). Screw the ring (tem 1) onto the housing-guard assembly (tem 8) until it is just snug. Too much pressure can damage the unit. WARNNG: The knife is sharp and can cut fingers. Guide the feed pan (tem 9) over the guard portion of the housing-guard assembly (tem 8) onto the pan stud (tem 7) and the pan support (tem 44). S. Locate the storage container under the clip (tem 24) and resting on the front legs (tem 23). 6. Connect power supply and actuate power switch (tem 25). WARNNG: Never put fingers or utensils in the throat of the grinder or the knife and plate interface. Page 2

5 Process MG22 Cut meat to be processed to fit under or through the safety guard. Recommended size is 1 '/2' thick x 3" wide x 12" long. Set meat in pan (tem 9). With grinder running, slide product under the guard of the housing-guard assembly (tem 8) or through the openings in the guard top. Use the meat stomper (tem 10) if desired,to guide product into grinding zone. The stomper is recommended for regrind. Collect ground product in storage container, Cleaning: Turn unit off and disconnect from power supply. Disassemble unit in reverse of assembly instructions - Remove storage container, feed pan, and then ring, plate, knife, worm assembly, and housing-guard assembly. WARNNG: The knife is sharp and can cut fingers. Clean components including the drive coupling (tem 15) by following the procedure: wash, rinse, sanitize, and air dry. Use the bristle brush provided to clean areas diflicult to access, Apply a small amount of food grade lubricant to bronze bushing, located inside the housing-guard assembly (item 8), before use. Page 3

6 LLUS. PART NO. ASSEMBLY DESCRPTON MG RNG,# PLATE, 3/16" PLATE 1/8' (OPTONAL) PLATE 1/4' (OPTONAL) PLATE 3/8' (OPTONAL) PLATE 1/2' (OPTONAL) KNFE, # ShAFT, FRONT WORM, # COUPLNG, WORM * STUD, PAN * ROUSNG-GUARD ASSY PAN STOMPER LOCK PN, PLATE STUD - SWTCH ACTUATOR KNOB STUD, MOUNTNG COUPLNG, DRVE 2 2 SCREW HEX. RD. SS CAP 3/8-16 X 1 1/2" LOE WASHER, MOTOR KEY 1/4SQ.X1 1/ SETSCREW 1/4-20X1/4CUppT KEPNUT 3/ GEAR MOTOR LEG, FRONT CLP, BUSS BOX SWTCH, START/ STOP SLEEVE, FRONT LEG HOUSNG, WELDMENT SCREW HEX. RD. CAP 4-40 X 3/4 LOE SWTCH, SAFETY NSULATOR, SAFETY SWTCH BRACKET, SAFETY SWTCH ELASTC STOP NUT WASHER LOCK WASHER HEXNUT1O ELASTC STOP NUT - MO X CONTACTOR 115V, 60HZ CONTACTOR 100V, 50-60HZ CONTACTOR 230V, 60HZ STARTER, 115V, 60HZ (CANADA ONLY) STARTER, 230V, 60HZ, (CANADA ONLY) STARTER, 230V, 50HZ, PH (EUROPE ONLY) CONTACTOR, V, 50HZ, RAL, DiN SCREW HEX. RD. CAP 1/4-20 X 1/2 LOE LOCK WASHER 1/ ** LEG,REAR FEET, REAR 2 Page 4 QTY.

7 * LLUS. NO. 71S NCLUDED WTH LLUS. NO 8 ** LLUS. 40 NCLUDES STUD M X 22MM MG22 LLUS. PART NO. DESCRPTON QTY STRAN RELEF COVER, HOUSNG SUPPORT, PAN SLEEVE, PAN SUPPORT SCREW, FLAT RD SLT SS X 3/ SCREWPPHD.10-32X1/2LG RUBBER STRP STORAGE CONTANER (NOT SHOWN) POWER CORD (NOT SHOWN) CORD, MOTOR (NOT SHOWN) LABEL, UNVEX (NOT SHOWN) LABEL, (NOT SHOWN) 54 RESERVED BRUSH, CLEANNG (NOT SHOWN) CONNECTOR. 3/8 (NOT SHOWN) WRNG PKG. (NOT SHOWN) Page 5

9 MG22 WRNG DAGRAM 115/ V, 60HZ, PH V, 50HZ, PH POWER N / BLACK W-tE GND W r 4, SAFETY SWTCH L J. MAGNETC CONTACTOR L3cr 3h] 14 -J W7 W2 W4 PART NUMBER STOP PWTCH START SWTCH,,, W3.. o-f---- L,._ J L WRE NO. GA WRE SEE NOTE ABLE LENGTH l4 NCHES W8 W5 END A SEE NOTE MOTOR END B COLOR SEE NOTE 1 W WHTE W W3 S 3 2 (/2 1 2 WHTE RED W BLACK W5 S 3 25 RED we S 3 2 (/2 RED W (/2 RED W8 MOTOR CORD NOTES:. DOUBLE CRMP FERRULES, KLAUKE 72/OVZ OR AMP , MOLEX-ETC BB MATERAL: 6GA 1015 TEW CSA AND UL APPROVED. MPORTANT; Before making electrical connections, check the specifications on the data plate (located on the rear panel) to assure they agree with those ofyour electrical service. WA.RNJNG: Whenever maintenance is being performed, or whenever the top cover has been removed, DSCONNECT electrical cord and place a tag on it indicating the slicer is being worked on. Page 7

10 WRNG DAGRAM CANADA & CE 115/ V, 60HZ, PH 230V, 50HZ, 1PH SAFETY SWTCH r i L..J W STARTER / L POWER N L2 L3 ONO 9 W6 - OVERLOAD RELAY - S JD.-O _95 A L L2 L3 13 A2 T T2 T3\,014 T W8 W7 W2 W4 STOP START SWTCH \ SWTCH H...1 W3 o W5 W9 MOTOR PART NUMBER WRE NO. GA SEE NOTE WRE TABLE LENGTH END A N NCHES SEE NOTE END B 'COLOR SEE NOTE W WHTE W WHTE W /2 RED W BLACK WS RED PART W /2 RED OF W /2 RED STARTER W /2 RED WO MOTOR CORD NOTES:, DOUBLE CRMP FERRULES. KLAUKE 72/OVZ OR AMP MOLEX-ETC BB MATERAL: 6GA 1015 TEW OSA AND UL APPROVED. MPORTANT: Before making electrical connections, check the specifications on the data plate (located on the rear panel) to assure they agree with those of your electrical service. WARNNG; Whenever maintenance is being performed, or whenever the top cover has been removed, DSCONNECT electrical cord and place a tag on it indicating the slicer is being worked on. Page 8

nivexexacting Standards, Just Like Yours, since sirce 1948

nivexexacting Standards, Just Like Yours, since sirce 1948 SRMO/SRMFO SRM0/SRMF0 SRM0/SRMF0 Swing Ring Series SRM0/SRMF0 SRMO/SRMFO PLANETARY MXERS Maintenance & Parts Manual Maintenance & Parts Manual