K6JRF's Page formerly W6FZC
|
|
- Austen Gardner
- 5 years ago
- Views:
Transcription
1 K6JRF's Page formerly W6FZC My Mercedes Benz S500 Coupe (Updated: Nov 9, 2004) Analyze and Troubleshoot "Check Engine" MIL and Electronic Control Units (ECU)! Seat Belt Extender About one month ago, the driver's side Seat Belt Extender (SBE) tried to reverse itself while it was not extended and as a result, it managed to damage itself. It made such a racket for 20 seconds and after it stopped, it made a loud 'clunk-clunk' sound when the arm extended. It still operated OK if you could live through the noise but who knows how long it would last. How-It-Happened I've had this car for 6+ years and the SBE has never malfunctioned. The way this happened is an interesting story. My wife got into the car on the passenger side as she normally does and started the car by leaning over and turning the key, something she has NEVER done. I was not in the car and did not close the driver's door fully; it was closed but not 'latched'. The 'S' cars have an automatic feature that 'pulls' the door closed tightly when it's triggered. The normal operation of the SBE requires that you be in the seat with the door CLOSED and the ignition key 'ON'. Then the SBE will extend the seat belt. When I got into the car, sat in the driver's seat and closed the door, the SBE didn't extend, instead it started to retract. Since it was already retracted, it proceeded to 'grind' the gears for about 20 secs. It obviously 'thought' it was extended, thus the damage to the gears. I'm pretty confident that this chain of events caused the problem but I'm not about to TEST that theory now that it's fixed! Yes, I asked her to NEVER do that again! Yesterday, I took it apart to see what could be done; after getting it apart and removed from the car, you could plainly see broken teeth on the drive gears. A call to the local MB dealer produced a lot of shock... replacement is $560 plus tax, about $600!. There was absolutely NOTHING wrong with it except for the damaged gears. So I decided to see if I could find a 'junked' unit and get the gears from it.
2 After calling a few places, I found a SBE from a W124 chassis which I got 'free'. Now you can't beat free! So I took it home and after comparing the two assys, found that the gears were ALMOST identical! Great happiness! The ALMOST will be explained as I go on. The W140 part number: for the drivers side. The passenger side unit's part number is different. The W124 part number: for the passenger's side. The driver side unit's part number is different. Now the good news! The gears from either can be used in the other unit! So I proceeded to take it apart and remove the two needed gears. After inspecting them closely, I found that the small gear was slightly thicker than needed. Since they are made from nylon, it was a simple matter to sand off the excess to make it fit perfectly. The other problem is that the second gear spindle is a little smaller that the original. There was no solution for this but it didn't retard the operation since the two gears are under tension when assembled. SBE Removal The following disassembly instructions refer to the drivers side. In order to repair the SBE, the rear seat side panel must be removed to gain access to it as the SBE assy is mounted to the car's sidewall for stability.
3 To start, remove the rear driver's side seat bottom. This gains access to the seat back which is held by one bolt (#10). Remove the bolt and lift the rear seat cushion out. Now you can see the complete side panel. On the car's frame at the bottom of the panel, remove the screw that holds it down. Next, with a proper panel puller tool, remove the leather panel cover. It unsnaps easily. Now you will see two (2) screws near the 'handle' that hold the panel to the side frame; remove these and start to work the panel loose. As is the custom with Mercedes, the panel is held by 'clips' on the top side. So you need to gently lift the panel 'up' and out. Once that panel is removed you can now see the SBE unit. Remove the three (3) screws that secure the unit to the side wall of the car and unplug the cable from the electronic control box located just below the SBE on the side wall. You should now have the complete unit ready to 'operate' on your work bench. Bench Repair of SBE With a little inspection, you will see the damaged gear(s). For my unit the smaller gear as shown below, was 'shaved' bald for four (4) teeth. After inspection, the main drive gear had two (2) 'chipped' teeth most likely due to the scraping action that occurred when the unit reversed itself. I hadn't planned on replacing the second gear but after seeing the two 'chipped' teeth, I decided that it needed to be replaced since it could catch and cause the same problem to occur. It's a simple matter to remove the parts from the W124 SBE to use in rebuilding the W140 unit. The picture shows a 'recreated' version. On close inspection, you can see that both gears are from my 140 SBE assy. I put them back into the 124 SBE assy for comparison so you can see how they go in.
4 First loosen the spring so that it can be removed. Then loosen the two (2) screws that hold the Limit Switch. Now you can lift out the gear assy in the 'black' housing so that you can remove the two gears. After that, it's a straight forward task to reuse the gears in the 140 unit and restore it to perfect condition.
5 To replace the gears, you need to remove the 'spring tensioner'. To do this, push with a large screwdriver until the block releases the spring. Then loosen the screw that holds the 'gear assy' (black plastic) and replace the gears. Then just re-assemble the SBE making sure to plug-in the cable to N42, the SBE Controller module. SRS Light is ON When I removed the side panel, the R12/1 squib connector to the Emergency Tensioner Retractor (ETR) was jarred loose. This connector, with red colored end, is not like the typical Mercedes connector in that it does not have 'clips' that lock it into place. It just plugs in and it can be easily jarred loose. When I tested the SBE, the SRS light illuminated and stayed on. After reading the SRS codes (MENU #11), it pointed to the ETR R12/1 squib. Looking at the ETR, the loose connector was spotted. After plugging it in and performing a RESET, the SRS light when out. For the SRS system, you MUST reset the codes since once tripped, only resetting with the proper tool (a scanner) will the SRS light go out. Send me with your comments
Door Panel Removal & Window Stop Adjustment
Door Panel Removal & Window Stop Adjustment By: Jeff Wolford Disclaimer: This is simply an article of how I fixed my car. I m not responsible if you break, scratch, or mess up anything following my example.
More informationInstalling the Dan-Marc and Pingel setup.
Installing the Dan-Marc and Pingel setup. This is an alternative to the OEM vacuum petcock. It's the setup I use and feel more comfortable with it. Many still like the OEM vacuum petcock and they can continue
More information4TH GEN SEATS IN A 3RD GEN TRUCK
4TH GEN SEATS IN A 3RD GEN TRUCK by Flopster843 02 Oct 2016 If you drive a 3rd generation Dodge Ram truck, I am sure you have discovered that the OEM seats are not the greatest (Figure 1.) They are extremely
More informationTiming belt change. Timing belt change
Timing belt change Put 2 new Gates T275 timing belts on today. Tensioner drilled smooth and tight with less than 16,000 miles on her decided not to change the tensioners just the belts. You'll need some
More information1986 Rear Disk Brake Upgrade. All hard lines mounted to the rear axle with mounting screws. 1/4" fittings
1986 Rear Disk Brake Upgrade Being well prepared for a project of this size is the key to success. I thought I was well prepared by doing a lot of research and getting all of the required parts before
More informationTroubleshooting Guide for Limoss Systems
Troubleshooting Guide for Limoss Systems NOTE: Limoss is a manufacturer and importer of linear actuators (motors) hand controls, power supplies, and cables for motion furniture. They are quickly becoming
More informationInstalling Seat Belts in my Tudor August 2009 My '29 Tudor was restored about 25 years ago by my brother-in-law. He restored it to close to original, but made a few changes that many will claim are for
More informationRear Wheel Removal (by BassCliff)
Rear Wheel Removal (by BassCliff) Hello to my GS riding friends! After picking up a nail in my rear tire (while on the freeway at 75mph!) I thought I would take a few pictures to help illustrate the rear
More informationRV8 boot lid lock and boot light switch
Godfrey Dennis has some useful pictures of the lock on the boot lid on his RV8 which he feels should help to clarify the metal tab which acts as the switch mechanism for the interior boot lamp, particularly
More informationProjector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation
Projector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation Now it is time to remove the headlights! Obviously you have to open the hood to do this. 100_3630.jpg
More informationBrake System Rebuilding the brake calipers
Page 1 of 39 Brake System Rebuilding the brake calipers Written by the backyard hack mechanic Sean750 Document history: # 14 Jan 2004 added pictures of rear caliper rebuild kit # 13 Nov 2004 added more
More informationHow to replace your Turbo Actuator Step by Step
How to replace your Turbo Actuator Step by Step Special thanks to other forum members who have previously dealt with this problem! Old By Chirpz New Your Turbo is a lot tougher than the electric actuator
More information*Some speedometers have these additional electronic connections. If yours does, then remove the smaller slotted screws shown.
www.odometergears.com 1981-1985 240 Cable-Driven Speedometers (NOT for 1986 and later electronic units) http://www.davebarton.com/240-odometer-repair.html For this set of instructions below, I will not
More informationTroubleshooting Guide for Okin Systems
Troubleshooting Guide for Okin Systems More lift chair manufacturers use the Okin electronics system than any other system today, mainly because they re quiet running and usually very dependable. There
More informationTiming the 9N/2N Steering Sector Gears
Timing the 9N/2N Steering Sector Gears by John Korschot - www.johnsoldiron.com (May 2010) The procedure for timing a set of steering gears in the 9/2n tractors is published in the I&T FO4 shop manual.
More informationTroubleshooting Guide for Dewert Systems
Troubleshooting Guide for Dewert Systems Dewert electronics aren t as common as Okin systems as they re mainly used by one manufacturer (Pride). However, Pride is the largest lift chair manufacturer in
More informationPeugeot 406 Coupe: Delocking your boot V.1 April 2005
This is a first stab at a DIY guide to de-locking your 406 Coupe. It isn t a hard modification to do yourself, but you do need to be confident working on your cars electrics and removing and refitting
More information2003 BMW 325xi 2.5L Straight 6 About 120K Miles; Looks Well Kept Multi Strike COP Ignition. History. Customer bought used about 3 months ago
2003 BMW 325xi 2.5L Straight 6 About 120K Miles; Looks Well Kept Multi Strike COP Ignition History Customer bought used about 3 months ago Claims since day one runs rough on cold start Sometimes MIL would
More informationFord Super Duty Dash Lighting LED Upgrade F250 4x4 XLT Sport Crew Cab
Page 1 of 32 Ford Super Duty Dash Lighting LED Upgrade 2004 F250 4x4 XLT Sport Crew Cab Back to 2004 F250 Main Page Click Here for a PDF version of this article ** Updated 12/15/09 ** New version of the
More informationAamir_bt The legend..
Aamir_bt The legend.. How to do timing on a 4XE1-W (DOHC) engine. well i decided to to a write up for DOHC timing since there was only the SOHC written up, and i had to do a timing belt on my stylus anyways,
More informationHow to change Swirl Flaps, on Diesel BMW
How to change Swirl Flaps, on Diesel BMW I am now going to show you how i did it on my car. May'sedition of Total BMW (still in WHSmiths) did a cover on how to change and modify Swirl flaps on a 330d engine,
More informationFD Transmission Rebuild: Parts Inspection
FD Transmission Rebuild: Parts Inspection Now that everything is disassembled, cleaned, and bagged in labeled Zip-Locs, it s time to decide what to replace. Warning: I m not a transmission specialist I
More informationHere's the difference (externally) in the and 04+ bumper and headlights: (00-03 on top, 04 on bottom)
OK guys, I've been meaning to post this for awhile.. well here it goes. I did the '04 front end conversion on my '01 about 4-5 months ago, but then the dealer had to buy the car back for legal reasons.
More informationKodak 750H Carousel Projector Repair
Kodak 750H Carousel Projector Repair An AT YOUR OWN RISK PROJECT by Klaus Wolter, Rev B, 3-26-2016 Here I documen the repair of my 750H carousel. A common problem with this projector, and all of the projectors
More informationSteelmate TP-90 Review July 2016 OVERVIEW I needed a TPMS (Tire Pressure Monitoring System) to monitor the tires on my LeesureLite trailer. I have an existing TPMS system on it however the monitoring device
More information2000 Mr2 Spyder Seat Cover Replacement Project
2000 Mr2 Spyder Seat Cover Replacement Project Tool List: Plastic Trim Tool, Hog Ring Pliers, Medium or Heavy Duty Wire Cutters, 12mm socket, 14mm Socket, Ratchet, Extension, Flat Head Screwdriver & Gloves
More informationBrake master cylinder replacement
Brake master cylinder replacement 8-25-2010 I had replaced the front brake master cylinder a few years ago when it developed a bad leak, at that time, I ordered a new master cylinder from Spartan, very
More informationAir Compressor/Water Pump IV - Pilot Valve Stem, Test & Installation
Page 1 of 8 Air Compressor/Water Pump Part IV Pilot Valve Stem, Test & Installation Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 1/13/04 Last Revised: 0 Valve Test: I decided to test the steam valves
More informationConverting an A to 12v and Adding Turn Signals Bill Lee
Converting an A to 12v and Adding Turn Signals Bill Lee Bill@WRLee.com When I bought my 1929 Tudor, it had been restored about 20 years earlier. It had halogens and had been converted to 12v negative ground,
More informationInstallation Manual for LCD Boost Controller device.
Installation Manual for LCD Boost Controller device. Main Black box front view. The lonely white 4pin connector above means this box is equipped with the optional serial expansion card. Main black box
More informationAdjusting brake shoes for AutoPark parking brake
Adjusting brake shoes for AutoPark parking brake This document is a compilation of several separate writeups. What we're trying to do here is consolidate the necessary information needed for you to make
More informationDIY: Shiver Valve Check, Illustrated
DIY: Shiver Valve Check, Illustrated By Petemoss, AF1 Forum Tools needed: 4mm allen wrench to remove all the fairing pieces 2.5mm allen wrench to remove battery holder 5mm allen wrench for valve cover
More informationDOC # REPAIR SEAT BELT RETRACTOR
16 June, 2018 DOC # REPAIR SEAT BELT RETRACTOR Document Filetype: PDF 463.24 KB 0 DOC # REPAIR SEAT BELT RETRACTOR Step 1: Start off by getting any kinks or binds out of the seat belt. Prices start at
More informationChanging the Struts on a WK Jeep CRD
Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading
More information1999 BMW K1200 LT: Plastic Removal
1999 BMW K1200 LT: Plastic Removal Well, it had to happen. While removing the plastic that covers the handle bars to see where to route power for GPS and/or radar detector the tip of the torx driver fell
More informationHow to replace or adjust the altitude clutch of the NexStar N11GPS
Langenbrettach/Germany, February 10 th 2004 Matthias Bopp How to replace or adjust the altitude clutch of the NexStar N11GPS Table of content How to replace or adjust the altitude clutch of the NexStar
More informationINSTALLATION INSTRUCTIONS
Backup Camera Interface (Kit # 9002-7762) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Cam T-Harness Plug & Play I/O T-Harness
More informationInstalling the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version)
Installing the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version) September 2, 2018 Tools needed: Wireless charger upgrade kit Plastic trim tools 7 mm nut driver Background: I purchased the
More informationLJ20 Distributor - Disassembly Inspection Repair
LJ20 Distributor - Disassembly Inspection Repair Old Codger New To Old Suzuki Jeeps The odometer on this 1972 LJ20 indicated the distributor had less than 10,000 miles of wear but during that time it had
More informationStarter One-Way Clutch Replacement
Starter One-Way Clutch Replacement by Joe Conway YOU NEED THE RIGHT TOOLS TO DO THIS JOB!! IF YOU HAVE ANY HESITATIONS TAKE IT TO A SHOP. I CLAIM NO RESPONSIBILITY FOR DAMAGE DUE TO MISTAKES MADE DURING
More informationPage 3. Misc. insulator pads to go under the inverter and spark box. I used the packing material from around a glass jar
Page 1 Convert vehicle 1978 Chevy Camaro with stock 350 engine, automatic trans. Stock 4-barrel carb, and stock fuel pump. The gas tank has been changed to a metal water tank and the fill cap is vented
More informationHere we have the old lock on an exterior door (note more than one door was used for this article- taking the best pictures of the group)
Alarm lock T2 Part 1 of 4 Installations Eugene Hansen 2004 This is the first part of four, 1st we will install a T2 Trilogy, 2 nd replacing the batteries, 3 rd replacing the solenoid and finally 4 th reprogramming
More informationHow To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg
How To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg Skill Level: Easy Disclaimer: Please use caution and seek professional assistance when necessary. ColoradoFans.com,
More informationMC Xpress AB Norra Altervägen ALTERSBRUK Sweden
Installation manual turbo kit SkiDoo/Lynx ACE 900 1 MC Xpress AB Norra Altervägen 821 945 92 ALTERSBRUK Sweden Tel: +46 911 202005 Fax: +46 911 202008 www.mcx.se Supreme of the extreme! Thank you for choosing
More informationRetro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010
More informationTrouble Shooting Guide for Hubbell Systems
Trouble Shooting Guide for Hubbell Systems NOTE: Hubbell Special Products discontinued operations in 2008, so there is a very limited number of repair parts available for motor repair. In some ways, this
More informationDisco 3 Clock Spring / Rotary Coupler replacement
Disco 3 Clock Spring / Rotary Coupler replacement I recently had to change my Clock spring and thought some folks may find it helpful to see what it entailed. I did lots of reading around but couldn t
More information2008 Toyota Tundra 4WD Brake Job: A Quick Job and Even Quicker Write-Up.
FRONT BRAKES: 2008 Toyota Tundra 4WD Brake Job: A Quick Job and Even Quicker Write-Up. 1. Remove this bolt holding brake line bracket to the suspension. 2. I had to replace all 4 rotors at 60K miles, so
More informationwww.odometergears.com Mercedes-Benz Mechanical Odometer Repair This how to can be used for all mechanical repairs as the only difference will be the removal of the instrument cluster. http://www.dieselgiant.com/repairyourodometer.htm
More informationLincoln Mark VII T5 Swap Version submitted by 5.0 bird
Lincoln Mark VII 1984-1989 T5 Swap Version 20070611 submitted by 5.0 bird I've decided to make an article to assist with the T5 swap for the 84-89 Mark VIIs, since I was just in there because my DOA didn't
More informationShould I Leave My Manual Car In Gear When Parked
Should I Leave My Manual Car In Gear When Parked I just wanted to know who people leave there car in first gear while there car is It's definitely saved my car a few times since my parking brake cables
More informationThe Body Slinger
http://www.scaryguys.com/slinger.htm The Body Slinger The body slinger is a nifty animation that looks like a benign corpse in a coffin until its triggered, then leaps almost straight up over your head!
More informationSingle Barrel Shotgun HPFP Install Guide
Single Barrel Shotgun HPFP Install Guide Thank you for purchasing the VTT Single Barrel Shotgun HPFP upgrade kit! PLEASE READ THE ENTIRE GUIDE BEFORE BEGINNING INSTALLATION! The first thing you should
More informationUpdated May 2015 Okay this is what I learned while converting several Yamaha SUV 1200 jet skis with a 2 stroke engine to a 4 stroke engine. I believe that you can use a Yamaha FX or VX four stroke for
More informationFanatec GT3RS V1 to GT3RS V2 Tutorial
Fanatec GT3RS V1 to GT3RS V2 Tutorial by Roy Visser 1 How to update your Fanatec GT3RS V1 wheel to a GT3RS V2 wheel Welcome to this guided and detailed tutorial for upgrading your Fanatec GT3RS V1 wheel
More information1 of 2 9/4/ :27 AM
Ford Mustang IAC IAB - Solving your idle problems http://www.muscularmustangs.com/iac.php 1 of 2 9/4/2010 10:27 AM Solving idle problems part 1 - Cleaning your IAC Does your idle rise and fall over and
More informationThe Invision kit comes with everything you need to install the DVD players into your X5; two leather headrests with integrated DVD players, two
Our BMW X5 plays a lot of roles in our life daily driver, tow vehicle, household hauler, etc. but the most important is Mommy Mobile and road trip car. The X5 makes a great long distance cruiser; it comfortably
More informationNow we re ready to install our new mounts. The picture on the right shows our old and new for comparison.
Well I didn t have a chance to write last week so we have a little catching up to do. Last Sunday I started out with setting up a jig to weld in the mounts. The jig is made out of a old fork tube that
More informationFigure 1: Valve housing smooth vs. o-ring groove
If you are driving an older Corvette, and by that I mean a C2 or C3, it will eventually get to a point where the Power Steering Control Valve (PSCV) will leak and require attention. In 2002, I had to repair
More informationXD Aussie Locker XD Installation Supplement Dana 35 Ford TTB
XD-13527 Aussie Locker XD-13527 Installation Supplement Dana 35 Ford TTB Thank you for your purchase of the XD-13527 Aussie Locker for Dana 35 Ford TTB The following installation review is from username
More informationAudi A8 Transmission Service By Barry Lenoble and Paul Waterloo
Page 1 of 18 Technical & Maintenance Upgrades & Style Used A8 Buyer's Checklist Marketplace On Track Gallery Links Contact Home Audi A8 Transmission Service By Barry Lenoble and Paul Waterloo Background
More informationAnother CJ picture guide to replacing the key cylinder in a non-tilt steering column
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationMGB V8 Roadster restoration project Report 67
19th August 2016. This report jumps a bit from one subject to another. If I need to put some thought into a certain aspect of the rebuild I tend to get on with another job and sleep on the problem until
More informationShotgun Double Barrel HPFP install guide
Shotgun Double Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Double Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationAnother CJ picture guide to
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More information1999 Chevrolet Tahoe - 4WD. DTC P1345 Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation
1999 Chevrolet Tahoe - 4WD DTC P1345 Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Circuit Description This diagnostic trouble code (DTC) monitors the crankshaft position (CKP) and the
More informationImproving the gearshift feel in an SW20.
Improving the gearshift feel in an SW20. Part one In 3 parts. The SW20 gearshift can be often be greatly improved by eliminating play in the shift linkages, and this article covers three areas that need
More informationBMW 2002 M42 Swap Notes-THIS IS NOT FINISHED
BMW 2002 M42 Swap Notes-THIS IS NOT FINISHED This document is to help those that want to install an m42 into a BMW 2002. It is based around an e30 engine, trans, and wiring. You can use the e36 block/head/wiring
More informationFeature Description. Version History
TA2 Malfunction Indicator Lamp (MIL) and Engine Protection Document Number: FD-0007 Author: J. Goodloe Version: 03 Publish Date: 2016-03-18 Feature Description Version History Version Date Modified Sections
More informationAmateur Radio Station WFØGM Repairing a Yaesu G-1000DXA Rotor
WFØGM Home http://wf0gm.fpage.com/index.htm Amateur Radio Station WFØGM Repairing a Yaesu G-1000DXA Rotor (Part 1 of 2) The following is my experience with a faulty Yaesu G-1000DXA Rotor, and how I repaired
More informationCorvette Set Separator (Glove Box) Lock Removal
1956-62 Corvette Set Separator (Glove Box) Lock Removal The materials here were gathered from several Corvette Forum Threads as well as from the Web Pages of Rich Mozzetta (rich5962 on the CF). Our colleagues
More informationPorsche 911 Gear and Pod Odometer Repair
www.odometergears.com Porsche 911 Gear and Pod Odometer Repair http://efinnegan.com/porsche/repair%20maintenance%20and%20miscellaneous%20info/odometer-rebuild.htm http://p-car.com/diy/odometer/ *************************************************************************************************
More informationInstallation Instructions Jeep CJ-7
Retrofit Steering Column Installation Instructions 1976-86 Jeep CJ-7 For Part # s 1520800010, 152800020, 1520800051 www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 (517) 424-0577 (517) 424-7293
More informationInstallation Directions for FINGER STICK and Blocker Plate
Installation Directions for FINGER STICK and Blocker Plate What is a Finger Stick? A Finger Stick is a simple circuit that modifies the MAF signal on LLY and LBZ engines (not LB7 engines) to expected levels
More information2012 SLK V6 (M276 Engine) Spark Plug Replacement
2012 SLK 350 3.5 V6 (M276 Engine) Spark Plug Replacement Proceed at your own risk. I read the Mercedes repair documents pertaining to changing the R172 SLK M276 V6 engine s spark plugs that I could find
More informationW C-230 Kompressor Sports Sedan 1.8l Thermostat Replacement & Antifreeze flush
W203 2003 C-230 Kompressor Sports Sedan 1.8l Thermostat Replacement & Antifreeze flush First, I have to thank everyone who has contributed to the MBworld.org forums without you; I would not have gotten
More informationAt Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job.
At Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job. My enormous thanks to forum members, particularly glorfindel, for their advice when
More informationVehicle Specific Instruction Notes
Vehicle Specific Instruction Notes Most later model vehicles use a plastic and felt anchoring strip in place of the older metal rods. We have provided rod pouches on all of our new seat skins that will
More informationHow I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B.
How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) By
More informationDown South Vettes Leather Sun visor Installation Instructions.
Down South Vettes Leather Sun visor Installation Instructions. Difficulty: 3 out of 5. Time: Plan on about 30 minutes. The tools used are:? A medium blade screw driver? A small flashlight may help get
More informationGearbox Assembly 101. Introduction. Before Beginning. By Mark Schutzer 4/13/06
Gearbox Assembly 101 By Mark Schutzer 4/13/06 Introduction If you are planning to re-motor an old brass locomotive you may want to upgrade to a new gearbox at the same time. The early 60 s and 70 s gearboxes
More informationChange to BLUE High Density LED in Dashboard for Volvo V
Change to BLUE High Density LED in Dashboard for Volvo V70-2001 VER. 1.1 1. Why we did it? Because 50% was not working. 2. We will try to show how to replace the original Lamps with LED in the Dashboard,
More informationAQA GCSE Physics. 55 minutes. 55 marks. Q1 to Q4 to be worked through with tutor. Q5 to Q7 to be worked through independently.
AQA GCSE Physics Magnetism & Electromagnetism 4.7.. - 4.7.2.: Magnets & Electromagnets Name: Class: Date: Time: 55 minutes Marks: 55 marks Comments: Q to Q4 to be worked through with tutor. Q5 to Q7 to
More informationBMW E61 Hydraulic Pump replacement instructions
BMW E61 Hydraulic Pump replacement instructions This DIY will guide you through the tasks needed to successfully replace your defective tailgate hydraulic pump Difficulty 3 of 10. The most difficult part
More informationBMW E46 318i M43, from r.
BMW E46 318i M43, from 08.2001r. Originally mounted steering wheel (with a airbag for two plugs): Pic. 1 Steering wheel to be mounted (along with the radio control and cruise control): Pic. 2 For start
More informationJDM B16 & OBD0 HONDA DISTRIBUTOR REPAIR
PDF Built By: tonyguns Source: Honda Tech JDM B16 & OBD0 HONDA DISTRIBUTOR REPAIR There are two things you should be checking before you begin. First, check the condition of the wiring harness. Pay close
More informationFront Suspension Redo
Front Suspension Redo Message: First, thanks to all the previous posters for guidance in my doing the suspension. As thanks, here s the updated document for doing the front suspension. Procedure: While
More informationMercedes Benz ABC Hydraulic Valve Block Solenoid Oil Seal Repair Fix Rebuild Kit Seals O-Rings Overhaul Install Instructions
instructables Mercedes Benz ABC Hydraulic Valve Block Solenoid Oil Seal Repair Fix Rebuild Kit Seals O-Rings Overhaul Install Instructions by x8rltd The Problem Vehicle sags on one or more corner after
More informationComments and facts below in chronological order as testing progress. Added non Added resistive Total load Watt meter kwh resistive
Comments and facts below in chronological order as testing progress Date Added non Added resistive Total load Watt meter kwh resistive from grid Jan 13 6 + 9 = 15 W 15 W 16 Jan 17 3 x 27 = 81 W 96 W 100
More informationShay - Painting The Trucks & Frames
Shay - Painting The Trucks & Frames Nelson Riedel Nelson@NelsonsLocomotive.com Initial:2/23/04 Last Revised: 06/06/2004 Painting of the locomotive trucks and frame are described in this page. The tender
More informationUpdated Automatic Bilge Pump Control By Allan Wing
Updated Automatic Bilge Pump Control By Allan Wing Recently a club member had asked me to post an article describing an automatic bilge pump controller on our club web site. The controller was designed
More informationExperience Matters: ADAS UX
Experience Matters: ADAS UX WardsAuto UX Solving UX Issues October 5, 2017 Kristin Kolodge Executive Director, Driver Interaction and HMI Technology User Experience Satisfaction 2 User Experience Model
More informationRedlineGoods Tacoma Installation Manual
RedlineGoods 2016+ Tacoma Installation Manual AUTOMATIC SHIFT BOOT AND EBRAKE BOOT Press down on the factory shift boot collar to disconnect it from the shift knob. Unscrew shift knob Pull up on the rear
More informationVolvo 1800 Dash Pad Replacement
Volvo 1800 Dash Pad Replacement (courtesy of John Garden State Chapter Volvo Club America) Reupholstering the dash Well it has been some time since I have been online in the forum. Winter is a quite time
More informationRobison On Rovers Carbon Fouling A New Kind of Valve Job
Robison On Rovers #3, April 20, 2000 By John Robison 1,680 words Robison On Rovers Carbon Fouling A New Kind of Valve Job In the last Robison on Rovers we diagnosed and disassembled an engine that suffered
More informationLAMBO VERTICAL DOOR HOW TO GUIDE
-1 LAMBO VERTICAL DOOR HOW TO GUIDE Despite what you may believe, scissor doors are not that difficult to install. There are plenty of body shops out there that will charge you $2,000 - $10,000 for this
More informationBMW 528i E39 Sunroof Repair
These instructions will help guide you through the repair process for broken sunroof control rails on an E39 chassis. Before I get started, I want to give a shout-out to a couple people who also posted
More informationThis Tech Tip is from THANKS!
Page 1 of 6 This Tech Tip is from www.bmwe30.net THANKS! Resetting the service interval indicator lights on BMW E30's and similar You'll need a piece of electrical wire (10/15 cm) to serve as a jumper
More informationHW Prowler Carburetor Installation Instructions
HW Prowler Carburetor Installation Instructions Page 1 of 6 Carb Kit Contains: HW modified Mikuni 36mm pumper style carb Custom choke cable Fuel Line Clamp Instructions (2) Leaner and (2) richer main jets
More informationFor a while now I have been
TECHNICAL TRAINING Shift Pointers Author: Subject: Erratic 2-3 shift, code P0780 Unit: BAYA 5-speed automatic Vehicle Applications: 2003 Honda LX Essential Reading: Rebuilder Shop Owner Center Manager
More information