DIY: Shiver Valve Check, Illustrated
|
|
- Donna Chandler
- 5 years ago
- Views:
Transcription
1 DIY: Shiver Valve Check, Illustrated By Petemoss, AF1 Forum
2 Tools needed: 4mm allen wrench to remove all the fairing pieces 2.5mm allen wrench to remove battery holder 5mm allen wrench for valve cover bolts 8mm and 10mm socket wrenches 8mm and 10mm standard wrenches philips screwdriver set of valve clearance measurement shims rubber mallet to loosen valve cover probably something else I forgot Valve Clearances: My Aprilia Shiver service manual lists the clearance ranges as Intake :: mm ( in) Exhaust :: mm ( in) It is essential you do this check on a cold engine. Let the bike sit over night, or about 8 hours, after riding to ensure it is cool enough. Checking the valves is easy, but adjustments require removing parts that could allow the timing to shift and make the bike to be unrideable. I recommend you consult the Aprilia service manual for more details. Hopefully this guide will make visualizing the task easier.
3 To get to the valves, you need to remove quite a few parts. Go slow and take it easy, and you will be able to accomplish this in a few hours. Between doing the work, taking pictures, taking breaks, and helping my wife work on her SV, this whole job took me about 5 hours. My valves turned out to be in spec, so I didnt need to remove the cam shafts or adjust the valve clearances. That would have added more time. First things you gotta remove are the fairing pieces from the fuel tank. There is one piece around the ignition switch, and three pieces on both the left and right side of the tank. Be sure to also remove the bolts to the left and right of the ignition that hold the front of the tank down (shown with yellow arrows).
4 Once you have the fairing pieces off and the front of the tank loose, you can pivot the tank up. If you can, remove the braided drain hose from under the left rear part of the tank. I didn t do that and had some tension pulling the tank up until the hose released. The nylon braided hose is attached to a tray under the fuel valve that collects drips of fuel and routes it around the hot engine. This shows the fuel hose disconnected from the red fuel valve. The collection tray is laying below, on the cylinder head cover.
5 After the hoses have been disconnected, unbolt the tank and remove it. You will then see the top of the rear cylinder head between the battery and airbox. Remove the four head cover bolts, and the spark plug boot. Then remove the bracket holding the battery in place and slide the battery up to provide clearance for the head cover to come off. Below is what you will see under the cover. The valves are covered with a pair of cam shafts, each with a gear attached to one end. The shafts are turned by the action of a third gear that is powered by the cam chain. The gears and cam chain are visible towards the bottom of the photo above.
6 At this point, I checked the valves on the rear cylinder. To check the valve clearance, you need to get the cam lobe off of the top of the valve so that it isnt compressed. The easiest way to do this is to shift the bike into 6th gear and rotate the rear wheel while up on a rear stand. It is even easier to turn the wheel if you remove the spark plugs. I rotated the rear wheel forward, as that is the way the engine turns. A mechanical engineer buddy says it is OK to turn it in reverse too, but I didnt do that. When you turn the wheel it will turn the cams. You want the cams to wind up in the position shown below - note the cam lobe pointed away from the top of the valve (yellow circle). There is a second cam under the cover that can be checked through the window (yellow arrow). In case you havent checked valves before, this is the tool you need. It has many shims bound together, each of a different measured thickness. The ranges you will need are listed at the top of this how-to. The measuring procedure is to put a shim between the cam lobe and the top of the valve. The shim that fits with ust a slight drag is the correct measurement. If a shim doesnt fit or fits very tightly, then it is too big, so dont try to force them into the gap. If it gives no resistance, then it is too loose, and the next largest size shim should be tested.
7 While doing this work, be sure to do the other inspections. My coolant level was too low, so I topped it off with a 50/50 mix of anti-freeze and distilled water. Dont trust the people who set up your bike - verify levels yourself! To access the front cylinder, you will need to get the radiator out of the way. Remove the two bolts holding it on to the frame and horn bracket. Also remove the bolt holding the reservoir to the frame, and slide the radiator off the peg on the right side of the bike. You will then have slack for it to dangle down out of the way of the head cover.
8 Left side view. You can see where I have removed the evap canister and bracket. Good riddance! View of right side. the dangling reservoir kinda blocks the view, but provides the necessary clearance.
9 After removing the 4 head cover bolts and the spark plug boot, you can remove the head cover. If it is stuck on (likely), you can tap it with a rubber mallet to loosen it. NEVER use a metal hammer to loosen it, as you would likely crack or damage the head cover or cylinder body. Again, with the bike in 6th gear and up on a rear stand, rotate the rear wheel forward and get the cams rotated off of the valves. Then you can test with the clearance measurement tool like shown below.
10 All of my valves were within spec, so I didnt go any further. The only way to adjust the valves is to remove the cam shaft covering the errant valve and replace the shim under the bucket. To remove the cam shafts, you will need to remove the housing covering the shafts, with the opposite shaft pinned in place with a 6mm pin through the gear. Since I did not perform any adjustment, I will leave it to someone else to show the procedure to safely remove the cam shafts. I dont plan to open the heads up again until the 12k mile check. Sorry I couldnt go any further, but if it aint broke, dont fix it!
11 While I had everything apart, I added a longer vent hose to the tank to make up for the one i removed while removing the evap canister. To do that, I needed to separate the painted plastic cover from the black plastic tank. Below are pics of the two pieces, for the curious.
Prerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
More informationTiming belt change. Timing belt change
Timing belt change Put 2 new Gates T275 timing belts on today. Tensioner drilled smooth and tight with less than 16,000 miles on her decided not to change the tensioners just the belts. You'll need some
More information2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.)
2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.) I'm not saying this is the only way, or even the right way, but it worked for me. First time I've
More informationFord Racing BOSS 302 Engine Oil Cooler (11-14 GT)
Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets
More informationW C-230 Kompressor Sports Sedan 1.8l Thermostat Replacement & Antifreeze flush
W203 2003 C-230 Kompressor Sports Sedan 1.8l Thermostat Replacement & Antifreeze flush First, I have to thank everyone who has contributed to the MBworld.org forums without you; I would not have gotten
More informationAamir_bt The legend..
Aamir_bt The legend.. How to do timing on a 4XE1-W (DOHC) engine. well i decided to to a write up for DOHC timing since there was only the SOHC written up, and i had to do a timing belt on my stylus anyways,
More informationRear Wheel Removal (by BassCliff)
Rear Wheel Removal (by BassCliff) Hello to my GS riding friends! After picking up a nail in my rear tire (while on the freeway at 75mph!) I thought I would take a few pictures to help illustrate the rear
More informationCB500X Valve Checking/Adjustment Guide. Before starting:
Before starting: Removing the tank is much easier when it doesn t have much fuel in it. Consider running the tank to a low petrol level before starting the job. Forum members in both the UK & USA have
More informationAt Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job.
At Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job. My enormous thanks to forum members, particularly glorfindel, for their advice when
More informationHow to install the Barnett clutch and the stronger Oil Pump Drive Gear
How to install the Barnett clutch and the stronger Oil Pump Drive Gear Written by WildFred I m from Germany so please excuse my English and the spelling. The following procedure is a combination of the
More informationMercedes Diesel Valve Adjustment Procedure
1 of 30 5/30/2008 12:58 PM Home Cars for sale Trucks for sale Where we are Links to other diesel sites About us Why diesel? Diesel Videos How they work How they sound FAQ Dodge Diesel Maintenance tips,
More informationPictorial Installation : Schnitz 685cc piston kit for Kawasaki KLR650 Part 1: Disassembly by: JeremyZ
- 1 - Pictorial Installation : Schnitz 685cc piston kit for Kawasaki KLR650 Part 1: Disassembly by: JeremyZ Note: This pictorial was conducted on a non-california, US model 2009 KLR650. On California and
More informationReplacing Valve Guide Oil Seals
Many thanks to Sonicrete, Bucko and Lucksox who put me onto this whole way of replacing the valve guide oil seals without pulling the head or even taking the motor out of the frame. The key to it all is
More informationIn summary, the procedures includes removal of the belly pans, draining of the engine block, draining of the radiator, coolant mixing and refilling.
COOLANT DRAIN AND CHANGE PROCEDURE Recently, there was a request for a picture guide for draining/changing coolant (Robot808 and James-man) and since I was going to do this operation on Idaho (88), I took
More informationM62 Alternator Removal / Replacement (Water Cooled)
M62 Alternator Removal / Replacement (Water Cooled) Pre-Steps 1. Disconnect Battery Positive lead 2. Charge Your Battery with battery charger to full charge (So you new alternator wont have to work as
More informationI hope this guide helps you as much as Boomer Bob helped me. We re just sharing what we know to help out other folks. Best of luck! Phil C.
A brief tutorial on swapping cams for the Victory Cross Roads and Cross Country on the Victory Freedom 106 inch V-Twin Engine with 6 speed over drive transmission Disclaimer: Swapping cams on a Victory
More informationwww.odometergears.com Mercedes-Benz Mechanical Odometer Repair This how to can be used for all mechanical repairs as the only difference will be the removal of the instrument cluster. http://www.dieselgiant.com/repairyourodometer.htm
More informationE46 FUEL FILTER CHANGE Pics from CI
1 of 10 5/3/2010 1:48 PM E46 FUEL FILTER CHANGE Pics from 2001 330CI Bellows Expansion Joints Metal Bellows Expansion Joints in Every Style from Flexicraft www.flexicraft.com/metal_bellows Ask a BMW Mechanic
More informationLet's take a look at the components that make up this retrofit hose kit.
Thank you for purchasing your Rotax 912 Fuel Hose Kit. Please note that these directions are updated periodically as required and the current version will always be located on our website. These instructions
More information2008 Toyota Tundra 4WD Brake Job: A Quick Job and Even Quicker Write-Up.
FRONT BRAKES: 2008 Toyota Tundra 4WD Brake Job: A Quick Job and Even Quicker Write-Up. 1. Remove this bolt holding brake line bracket to the suspension. 2. I had to replace all 4 rotors at 60K miles, so
More informationBRAKE PADS REPLACEMENT
KLR650 Homepage Contact Me You must remove the "REMOVE-THIS" in my email address for it to work. This is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the accuracy
More informationAnother CJ picture guide to replacing the key cylinder in a non-tilt steering column
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationwhat you need to do is hit the taper housing as hard as you can with your hammers AT THE SAME TIME and at a slight angle, what will happen is you
first things first, get the car on axle stands and the wheels off. Open the bonnet to let more light through to the area in which you'll be working. The following guide shows the passenger side being done
More informationAnother CJ picture guide to
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationThere is hence three things you can do - add oil, adjust the temp that the clutch begins to engage, or do both.
As most of you may be aware, I have been doing a lot of research lately on our cooling system in the 80's including the fact that we have a dead spot on the OEM temp gauge which prompted me to not rely
More informationReplacing MK4 Golf/Jetta radiator mounts in-car
Replacing MK4 Golf/Jetta radiator mounts in-car This is a guide to replacing the radiator mounts in a MK4 Golf/Jetta. This involves moving the core support to the service position which allows you to do
More informationCold Air Intake Installation Instructions
BAVARIAN AUTOSPORT Cold Air Intake Installation Instructions PARTS LIST: PF BMWE36-4 PROCEDURE: 1. Using a flat-head screwdriver, loosen the hose clamp between the AFM and rubber boot leading to engine
More informationHere's a pic of my 2500 stall converter, and if you look closely, you can see the
On with the engine. The sick patient. Extracting the engine, with accessories and wiring removed. Note the poor condition of the heads. Working late into the night. Here's a pic of my 2500 stall converter,
More informationYOU MAY WANT TO FIRST TRY TO LOOSEN THE FILTER HOUSING
2005 XC90 Tune-up (5-cyl) Including: Oil Change - Spark Plugs - Fuel Filter - Cabin Filter First off - let me say that I am an amateur (at best) mechanic, and I claim no responsibility for whatever you
More informationBendix Hydroboost Repair
Bendix Hydroboost Repair Report this image Pic 1 the leaky power piston seal... (probably master cyl too.) Pic 2 PS fluid after spider removal and MC actuator rod Pic 3 Removing the accumulator (note 1/8
More informationThough Indian s 111-cubic-inch engine delivers a
TECH by Chris Maida Andrews Indian 111 Camshafts Part I: Removing the cams from the camshaft compartment Tools Needed Red Loctite Clean rags 6mm Allen 5/64" Allen 3/32" punch External circlip pliers Needlenose
More informationCAMSHAFT INSTALLATION INSTRUCTIONS FOR NISSAN KA24DE ENGINES W/DOUBLE ROW CHAIN (SEE LAST PAGE FOR USING JWT CAMS IN KA24DE W/SINGLE ROW CHAIN)
9/13 UPDATE CAMSHAFT INSTALLATION INSTRUCTIONS FOR NISSAN KA24DE ENGINES W/DOUBLE ROW CHAIN (SEE LAST PAGE FOR USING JWT CAMS IN KA24DE W/SINGLE ROW CHAIN) 1. It is highly recommended that an oil and filter
More information1999 BMW K1200 LT: Plastic Removal
1999 BMW K1200 LT: Plastic Removal Well, it had to happen. While removing the plastic that covers the handle bars to see where to route power for GPS and/or radar detector the tip of the torx driver fell
More informationv Porsche 928
1985-86 32v Porsche 928 Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger kit at this price relies
More informationEurocompulsion Camshaft Installation
Eurocompulsion Camshaft Installation Introduction, please read. The purpose of this article is too assist our customers with installation of a performance camshaft in the Fiat Multiair 1.4 Turbo. The operation
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationTools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve.
Before installing a shift kit, be sure the transmission is in good operating order. If your transmission is making noises, slipping, shifting bad or the fluid looks brown or smells burnt, take the transmission
More informationPhil s Ear Shave Procedure
http://06vn750.blogspot.com/2011/05/ear-shave-procedure-different-format.html 06VN750 Thursday, May 19, 2011 Ear Shave Procedure Phil s Ear Shave Procedure Preface: GENERALLY speaking: If you change the
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationChanging the Power Steering Belt
Changing the Power Steering Belt Brett Dukes (Maverick) from the BigJimny Forum has contributed this article to the Website. Many thanks. Whilst off-roading on Sunday, my alternator Fan Belt snapped -
More informationRear End Installation and Bearing Kit - 8.8in (86-12 V8; V6)
Rear End Installation and Bearing Kit - 8.8in (86-12 V8; 11-13 V6) Tools Required: Jack Stands 5 Floor Jack 2 Oil Pans 1 Wheel Blocks 2 Differential Oil 3 qts Friction Modifier 3 bottles Tube of Black
More informationFord Super Duty 5.4L Spark Plug Change F250 4x4 XLT Sport Crew Cab
1 of 32 Ford Super Duty 5.4L Spark Plug Change 2004 F250 4x4 XLT Sport Crew Cab Back to 2004 F250 Main Page Click Here for a PDF version of this article At close to 100k miles, I figured it was time for
More informationIgnition Timing - Honda 180-Degree Twins
Ignition Timing - Honda 180-Degree Twins First thing to do is make a quick test light - I used a 12 volt indicator bulb from a speedo. Test leads with alligator clips make hookup easy... The point plate
More informationDrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationHow To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg
How To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg Skill Level: Easy Disclaimer: Please use caution and seek professional assistance when necessary. ColoradoFans.com,
More informationGo-ped ESR750 / ESR750EX Rear Brake Installation Instructions
Go-ped ESR750 / ESR750EX Rear Brake Installation Instructions This kit provides all the parts you need to install a rear brake on your ESR750 or ESR750EX. It will not work on an ESR Sport, or other Go-ped
More informationДнепр) Russian Motorcycle Carburetors Part 2B: PZ-24 and PZ-28 Carburetor Assembly and Jet Drilling
Ural (Урал( Урал) - Dnepr (Днепр( Днепр) Russian Motorcycle Carburetors Part 2B: PZ-24 and PZ-28 Carburetor Assembly and Jet Drilling (applies also to K-37 K and K-38 K carbs) Ernie Franke eafranke@tampabay.rr.com
More informationPorsche 928 with 16v LH-Jetronic Fuel System
Porsche 928 with 16v LH-Jetronic Fuel System Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger
More informationInstallation Instructions and Suggestions For Jeep YJ Fiberglass Replacement Bodies
Installation Instructions and Suggestions For Jeep YJ Fiberglass Replacement Bodies Getting started with the removal of your existing Jeep body. Trust nothing to memory; take photos of everything at different
More informationLooking up the front of the engine from under the radiator. (Picture taken with belt under tension.)
8. If you re replacing the AC compressor drive belt as well, it s time to loosen its belt tensioner. The AC compressor belt tensioner is very obvious under the front of the car. Loosen the 13mm bolt, then
More informationCorrado Club of Canada. VR6 Engine FAQ. By: Dennis
Corrado Club of Canada VR6 Engine FAQ By: Dennis I thought I would snap a few pics of the engine compartment on my 1994 VR6 Corrado. First, this is the updated engine management system so it does have
More informationACURA NSX ABS/ALB Modulator Rebuild Procedure
Version 03 ACURA NSX ABS/ALB Modulator Rebuild Procedure I rebuilt my 1991 ABS/ALB modulator using this procedure. Please note that this will not guarantee that your ABS/ALB system issues will be resolved
More informationThis is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX
Adjusting the valve clearance on a 2L V6 FTO engine This is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX Disclaimer: This guide is to assist you
More informationBMW 528i E39 Sunroof Repair
These instructions will help guide you through the repair process for broken sunroof control rails on an E39 chassis. Before I get started, I want to give a shout-out to a couple people who also posted
More informationProjector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation
Projector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation Now it is time to remove the headlights! Obviously you have to open the hood to do this. 100_3630.jpg
More informationCackle cure Kit Installation by Pete Cleveland (aka FTE) for Dino Fuel Alternatives
Cackle cure Kit Installation by Pete Cleveland (aka F250_ @ FTE) for Dino Fuel Alternatives March 26, 2007 Test Vehicle: 2002 Ford F250 XLT, 7.3L PowerStroke TurboDiesel, 2WD, Crew Cab, SWB, SRW, 124,000
More informationHow To: Fit an enclosed induction kit to the V6
How To: Fit an enclosed induction kit to the V6 As a couple have done this I thought I'd have a go, but do a write up at the same time. Here's a quick summary of the equipment you'll be needing: 1 x Universal
More informationHydraulic Automatic Primary Chain Tensioner for Sportsters
Hydraulic Automatic Primary Chain Tensioner for Sportsters Installation Instructions Note: The factory service manual or equivalent for your motorcycle is highly recommended before attempting to install
More informationInstallation Instructions
Part Number: 10.109.01.109 Description: AUTOTECH Sport 270 Hydraulic Camshaft Note: If the job seems to be beyond your abilities, we recommend that you refer this installation to a qualified mechanic.
More informationAdjusting brake shoes for AutoPark parking brake
Adjusting brake shoes for AutoPark parking brake This document is a compilation of several separate writeups. What we're trying to do here is consolidate the necessary information needed for you to make
More informationSuperior Wheel Installation Guide (No Turbo removal)
Superior Wheel Installation Guide (No Turbo removal) This is the process used to install the Turbo Wheel without having to remove the Turbo from your Engine. It should take a maximum of 5 hours. Tools:
More informationdirtbikeworld.net - AUSTRALIA S LEADING DIRTBIKE FORUM Installation of KTM Australia s Racing Four Stroke Head Kit
Installation of KTM Australia s Racing Four Stroke Head Kit This kit is available from KTM Australia for a limited time for $143 and upgrades the head internals of any 2000, 2001 & 2002 model 400 and 520
More informationSpecial Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationRebuilding the Power Steering Pump for a 2007 Honda Accord 4CYL
Rebuilding the Power Steering Pump for a 2007 Honda Accord 4CYL Disclaimer: I have benefited greatly from others who have taken the time to post auto repair videos/tutorials online. To try and return the
More informationMishimoto Performance Aluminum Radiator w/ Stabilizer - Manual (97-04 GT, Mach 1; Cobra)
Mishimoto Performance Aluminum Radiator w/ Stabilizer - Manual (97-04 GT, Mach 1; 97-01 Cobra) Installed on: 2000 Mustang GT (manual transmission) Tools: 8mm socket 10mm socket 13mm socket 3/4" wrench
More informationBEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta).
BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta). Based on the procedure published by Volkswagen, but modified for the "average" shadetree mechanic. Some special
More informationThis is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the
KLR650 Homepage Contact Me You must remove the "REMOVE-THIS" in my email address for it to work. This is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the accuracy
More informationIntegrated Engineering MK7/MQB Cold Air Intake Install Guide IEINCI2 & IEINCI8
Integrated Engineering MK7/MQB Cold Air Intake Install Guide IEINCI2 & IEINCI8 Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation
More information1986 Rear Disk Brake Upgrade. All hard lines mounted to the rear axle with mounting screws. 1/4" fittings
1986 Rear Disk Brake Upgrade Being well prepared for a project of this size is the key to success. I thought I was well prepared by doing a lot of research and getting all of the required parts before
More informationSome tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000
Some tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000 Last change 2013-Oct-11 I bought Haynes manual for a starter. That s something well worth it s cost I believe.
More information2001 V70 T5 ETM Removal and Cleaning Directions
2001 V70 T5 ETM Removal and Cleaning Directions Howard Cheng howardc64@gmail.com 10/24/05 Version 1.4 Read this before you start I performed this ETM cleaning because I had gotten 2 reduced performance
More informationVWvortex Forums > Golf IV & Jetta IV > DIY: Timing Belt And Coolant Pump Replacement on 2.0 AEG! Pics Inside! (Printable Version)
VWvortex Forums > Golf IV & Jetta IV > DIY: Timing Belt And Coolant Pump Replacement on 2.0 AEG! Pics Inside! (Printable Version) Click here to print this topic. Post Title: DIY: Timing Belt And Coolant
More informationTach-Drive Distributor Reconditioning Joe Fisher PDF prepared by Dave Zuberer Link to Thread on the Corvette Forum (C1-C2)
Tach-Drive Distributor Reconditioning Joe Fisher PDF prepared by Dave Zuberer Link to Thread on the Corvette Forum (C1-C2) I just finished two Corvette tach-drive distributors. One was a 71 small block
More informationThis guide will explain how to remove the old springs from the car and replace them with lowering springs.
fubar Guide: Fitting lowering springs to the Mk2 Clio The method described below worked for me. I am not saying it is the only method to complete the task. I will not accept any responsibility for damage
More informationPCV System Repair on a Volvo 5-cylinder
PCV System Repair on a Volvo 5-cylinder by jblackburn» Tue Apr 06, 2010 12:28 am As any engine runs, there are gases from the top of the cylinders that escape past the piston rings and into the crankcase
More informationM52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit
Home BMW Solutions Porsche Solutions DIY Tech Engine Services Dyno Services Machining About Contact Store Tool Rental M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit This procedure
More informationSunroof Repair. Sunroof Repair TSB. The sunroof repair kit available for the J30 is part number Y20. See images at bottom of document.
Sunroof Repair This document is the text/images from the TSB (technical service bulletin) issued by Infiniti concerning the repair procedure for sunroof issues. Be advised that this is a LARGE, TIME-CONSUMING
More informationInstalling Rear Brake Pads on a WK Jeep
Installing Rear Brake Pads on a WK Jeep Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your rear brake pads. This is what I did after
More informationThe following information is gathered from pages of the Honda Aero Shop Manual.
Original write-up by W. Boyter The following information is gathered from pages 3.10-3.12 of the Honda Aero Shop Manual. First of all, pull all your spark plugs, make sure your transmission is in neutral.
More informationReplace clutch and flywheel * (Volkswagen Sharan 2010-Present)
Replace clutch and flywheel * (Volkswagen Sharan 2010-Present) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and if
More informationVolvo 850 Radiator Replacement Jason Reed 29 March 2013
This write up covers removing and replacing the radiator on a 97 855 GLT wagon with light pressure turbo and automatic transmission. This car has 162K miles. The radiator, which was original, developed
More information2012 SLK V6 (M276 Engine) Spark Plug Replacement
2012 SLK 350 3.5 V6 (M276 Engine) Spark Plug Replacement Proceed at your own risk. I read the Mercedes repair documents pertaining to changing the R172 SLK M276 V6 engine s spark plugs that I could find
More informationShay - Painting The Trucks & Frames
Shay - Painting The Trucks & Frames Nelson Riedel Nelson@NelsonsLocomotive.com Initial:2/23/04 Last Revised: 06/06/2004 Painting of the locomotive trucks and frame are described in this page. The tender
More informationTriumph Oil Filter Mount A Design By Glenn Phrog Davidson
Triumph Oil Filter Mount A Design By Glenn Phrog Davidson After a long and expensive rebuild, I wanted to offer my 1966 Triumph the maximum engine protection possible so I started investigating ways to
More information1972 Sportster exhaust
1 of 10 7/6/2015 10:51 PM 1 of 10 1972 Sportster exhaust Mount an old stylish factory exhaust to make the bike quiet. Harley made a one-piece muffler exhaust system for the 1972-1976 model years. It will
More informationCold Air Intake Installation Instructions
BAVARIAN AUTOSPORT Cold Air Intake Installation Instructions Page 1/5 3.06 INS264 NOTE: The vehicle shown for this installation is equipped with ASC+T. If your vehicle dos not have this feature, installation
More informationEngine, disassembling and
Page 1 of 38 13-1 Engine, disassembling and assembling Lock carrier, moving into service position Special tools and equipment 3369 support tool 1 - Bolts 2 - Bolts 3 - Bolts 4 - Bolts 5 - Bore 45 Nm (33
More informationPreparation. With the car on the ground you will want to:
Doing a stage 3 swap was a LOT of work Audi S4 Stage 3 (K04) Install Doing a stage 3 swap was a LOT of work. Just a lot of small and simple tasks really. Just make sure you keep track of what you re doing.
More informationAdjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003
SECTION ONE: Get Prepared - Tools Adjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003 Courtesy of: Half-Crazy Get a manual impact driver (the kind you hit
More informationESS INSTALL. The donor car /6 Cosmos Black/Sand UUC Short Shifter Brembo cross drilled rotors Phillips Nav System 16:9
ESS INSTALL The donor car.. 1997 540/6 Cosmos Black/Sand UUC Short Shifter Brembo cross drilled rotors Phillips Nav System 16:9 The install went in several stages. Disconnect the battery Stage 1 Remove
More informationThermostats, Radiator, Coolant Hose, Hydraulic Fan/Steering R&R PT38 8V92
REMOVING AND REPLACING THE THERMOSTATS, COOLANT HOSES, RADIATOR AND CHANGING THE HYDRAULIC FAN/STEERING FILTER/OIL/SHAFT SEALS ON A 1987 PT38 8V92 BY CURT SPRENGER March 2007 Thermostats, Radiator, Coolant
More informationPeugeot 406 Coupe: Delocking your boot V.1 April 2005
This is a first stab at a DIY guide to de-locking your 406 Coupe. It isn t a hard modification to do yourself, but you do need to be confident working on your cars electrics and removing and refitting
More informationM-Tuned reroute kit XX
M-Tuned reroute kit 14-161XX Manufactured and designed by: *Professional Installation Recommended but not required 1) Disconnect the negative terminal from the battery in the trunk. 2) Drain the coolant
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION FRONT KITS SUM-BK1422, BK1423, BK1424 1999-2006 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take
More informationFront Axle Pinion Seal Replacement
Front Axle Pinion Seal Replacement by Flopster843 10 Apr 2016 The AAM 925 axle used on the front of Dodge Ram trucks is a decent unit, but it does have its flaws. This axle lacks lockout hubs on the front
More informationHonda Super Cub Etc. Frame & Forks
Honda Super Cub Etc. Frame & Forks Introduction This section is all about how to strip, servioce and rebuild the frame and forks of the Honda Super Cub and other bikes using the same frames, plus all the
More informationThermo-Bob 1 Installation Manual: Kawasaki Concours
Thermo-Bob 1 Installation Manual: 1986-2006 Kawasaki Concours This is a basic guide for installing the Thermo-Bob 1 on a Kawasaki ZG-1000 Concours. The bike used in the following photos was a 1995 year
More informationService Bulletin Cylinder Head Service. September 17, 2002
Service Bulletin 02-047 Applies To: 1998 02 Passport ALL September 17, 2002 Cylinder Head Service BACKGROUND In the 1998 through 2002 Passport Service Manuals, some of the information on cylinder head
More informationCP3 Retrofit Pump Install:
CP3 Retrofit Pump Install: 2A 4 2 5 3 6 1.) Clean this area very well. No dirt = No troubles!!!!! Lay lots of Rags under and around the pumps, alternator and belts!!!!! This will save dropped tools, parts,
More information