For a while now I have been
|
|
- Charleen Pitts
- 6 years ago
- Views:
Transcription
1 TECHNICAL TRAINING Shift Pointers Author: Subject: Erratic 2-3 shift, code P0780 Unit: BAYA 5-speed automatic Vehicle Applications: 2003 Honda LX Essential Reading: Rebuilder Shop Owner Center Manager Diagnostician R & R What s Causing Third-Clutch Failures in Honda Five-Speeds? For a while now I have been interested in finding out what is causing third-clutch failures in Honda five-speed transmissions. An opportunity finally presented itself when a customer brought in his 2003 Honda LX with a 3.0L engine and a BAYA fivespeed automatic transmission. We had overhauled this transmission three years ago when the vehicle had 60,000 miles. Now with 134,000 miles the vehicle had an erratic 2-3 shift and code P0780 Problem in Shift Control System. When we disassembled the unit the only problems we found were burnt third clutches (Figure 1) and badly burnt fluid. The customer was not too happy with a vehicle that had experienced two transmission failures in 134K miles the original one at 60K and now the rebuilt that lasted 70K. So I bought the vehicle because I thought it would be perfect for finding the cause of the third-clutch failure, since we knew the vehicle s history. I wanted to put the transmission as close as possible to the condition in which it came in but in a workable state to obtain the readings we wanted, so we repaired the transmission only. That is, we replaced the third clutches and steels with Honda original equipment, installed an aftermarket rebuilt converter and thoroughly cleaned the valve body. We did this to find the original cause of the failure. When we rebuilt the transmission three years ago, we installed an overhaul kit with Honda original clutches; aftermarket rebuilt converter; new linear solenoids A, B and C; and new shift solenoids A, B, C and D. We did not replace the bushings in the mainshaft or the countershaft, since at that time we did not have the tools to replace them. We also did not re- 1 flash the PCM to the latest software or replace the pressure switches. I connected our test equipment to the vehicle (Figure 2) to obtain as much data as possible. I obtained main line-pressure readings 3 During 2-3 shift Channel 1 main line pressure, Channel 2 1st-clutch pressure Channel 3 2nd-clutch pressure, Channel 4 3rd-clutch pressure 2 50 Transmission Digest
2 along with the pressure reading for each application clutch, amperage reading at linear solenoids A and B, and voltage readings from each shift solenoid and the third and fourth pressure switches. I even monitored the duty cycles of linear solenoids A and B during upshifts and downshifts. I looked for any pressure lost in the third-clutch circuit while the transmission was hot, and as Figure 3 shows, third-gear oil pressure was within the 10-psi difference allowed between apply pressure and main line pressure. In this case it was equal to main line pressure, proving no pressure lost in circuit 30, which leads to the third-clutch pack. This is interesting, because as we mentioned at the beginning we did not replace the bushings in the countershaft or mainshaft, and by this time they had 134,000 miles of wear. After obtaining all this data, I sat down for hours analyzing it. I noticed something peculiar when looking at the recordings of the pressure readings taken during upshift and coast downshift. On the third clutch, pressure was present during a forced 4-2 downshift but not as much during the 5-2 downshift (figures 4 and 5). When I looked at the recordings made with the third pressure switch connected to the scope, I noticed that the pressure present was enough to close the third pressure switch (Figure 6). This third-clutch pressure was present from when fourth pressure was connected to CPC A pressure (Channel 3), through 2nd gear (Channel 1) and until third gear was fully applied (Channel 2), for a total of about 2 seconds and reaching at times 50 psi. This thirdclutch pressure reaches its highest when second-clutch pressure is fully applied at psi. That could not be good for the thirdgear clutches, but was it a cross leak? It was not present during all the upshifts or coast downshifts and not even during the 5-2 forced downshift. So that almost ruled out a cross leak, but how was this oil pressure getting into the thirdclutch circuit on a 4-2 downshift? 4 During forced 4-2 downshift Channel 1 2nd clutch, Channel 2 3rd clutch Channel 3 4th clutch, Channel 4 5th clutch To eliminate the possibility of a software update that might solve this problem, I had the PCM recontinues next page downshift Channel 1 2nd-clutch pressure, Channel 2 3rd-clutch pressure Channel 3 4th-clutch pressure, Channel 4 5th-clutch pressure November
3 Shift Pointers flashed to the latest software per Honda s bulletin. When I ran the same pressure test, no difference was apparent other than crisper 6 During forced 4-2 downshift Channel 1 2nd clutch, Channel 2 3rd clutch Channel 3 4th clutch, Channel 4 3rd pressure switch 7 Shift solenoids A, B & C on a 4-2 downshift Channel 1 solenoid A, Channel 2 solenoid B Channel 3 solenoid C, Channel 4 3rd-gear switch. shifts, so that ruled out a correction with a re-flash. After studying the hydraulic charts I discovered the reason for the presence of this oil pressure. Remember that the PCM modulates linear solenoids A and B to control the gradual engagement and disengagement of the clutches that are coming on and going off. It does this by slowly increasing or decreasing the amperage. For more details see A View into the Honda Five-Speed s Shifting in Transmission Digest, August Let s look at the PCM solenoid strategy during a 4-2 downshift, using the sweep reading of the scope in Figure 7 as an example. As you can see it takes three steps to accomplish a 4-2 downshift. We start with all solenoids off in fourth gear. 1) Solenoid C (blue) is turned on for about 0.3 second. This action moves shift valve C, connecting fourth-clutch-circuit oil to CPC A oil pressure, already at high amperage (high pressure), and makes the solenoid shifting strategy the same as for a 3-4 shift: SSA off, SSB off, SSC on. 2) Next, as solenoid C (blue) is being turned off again, solenoid B (green) is being turned on at the same time for about 1 second. This gives us the solenoid strategy for the 2-3 shift: SSA off, SSB on, SSC off. This solenoid strategy moves shift valve B and connects fourth-clutch pressure that is now CPC A oil pressure to exhaust port H4X at shift valve B. 3) Finally, solenoid A (yellow) goes back on, giving us the solenoid strategy in second gear: SSA on, SSB on, SSC off. Now let s look at what is going on in the hydraulic circuit during a 4-2 downshift (Figure 8). When SSC was turned on for 0.3 second, CPC B oil pressure that was beginning to modulate to lower amperage (Figure 9) increased in pressure. Because of the way the shift valves are placed by the solenoids, this CPC B pressure starts to enter third-clutch circuit through 52 Transmission Digest
4 8 9 SSA off SSB off SSC on 3-4 shift strategy 4-2 forced downshift Channel 1 linear solenoid A, Channel 2 linear solenoid B Channel 3 3rd-gear switch, Channel 4 4th gear shift valve C circuit 5C, through shift valve B, then through shift valve A and finally through circuit 30, third clutch. When SSC was turned off again and SSB was being turned on (0.7s on the time scale in Figure 7), CPC B oil continued uninterrupted into circuit 30 third clutch, this time through circuit 5D at shift valve C, through shift valve B, through shift valve A and finally to circuit 30 at shift valve A (Figure 10). Finally, solenoid A comes on, giving you second-gear solenoid strategy (SSA on, SSB on, SSC off). Third-gear oil exhausts at H3X through shift valve A when shift solenoid A is turned on (Figure 11). What makes matters worse is that, as figures 6 and 7 show, the 2-3 shift can start immediately if the gas pedal is backed off slightly, by turning solenoid C on. This does not give the CPC B oil present in circuit 30 enough time to exhaust. Because of the 2-3 shift strategy CPC B oil starts to enter again into circuit 30, or third clutch. On the basis of this finding, it is my opinion that this CPC B oil pressure present on a 4-2 forced downshift is dragging the clutches and contributing to an early thirdclutch failure. If we keep in mind that the third clutches are also applied momentarily during the shift continues next page SLAUSON TRANSMISSION PARTS Used, New & Rebuilt Hard Parts, Soft Parts, Electrical Components & Flywheels Slauson Transmission Parts MAKING HARD PARTS SIMPLE Order online at Slauson.com Phone Hours: Open 7:00 am to 5:00 pm/ PST Circle No. 10 on Reader Card November
5 Shift Pointers 10 from Neutral to Drive (Figure 12) and it requires only 36 psi to engage, we can imagine what 50 psi can do with the second clutch on with up to 130 psi. When these vehicles are being driven in fourth gear, it also does not take much throttle increase to get a downshift to second. On my many road tests on this car, 4-2 downshift was a normal shift when I entered the 11 SSA off SSB on SSC off 2-3 shift strategy SSA on SSB on SSC off 2nd-gear strategy 12 Neutral to Drive Channel 1 main line pressure, Channel 2 1st-clutch pressure Channel 3 2nd-clutch pressure, Channel 4 3rd-clutch pressure freeway. It is also my opinion that by increasing the size of the third piston in 2004, Honda made the problem worse, since now you have about 1 square inch more application area. I believe the solution would require a software change for the PCM or else the third clutches would have to be made to take this kind of abuse without sacrificing the 2-3 shift comfort. In the past four months I have been trying to find a solution. In looking into the PCM strategy, it would have to be programmed not to lower the amperage on linear solenoid B during a forced 4-2 downshift (Figure 8). In other shift situations linear solenoids A and B are modulated independently of each other. There may be other reasons why Honda has decided to program it this way, but trying to talk with the company did not produce any results. My next approach was through the clutches. I tried talking with some clutch manufacturers, but the only one that took the time to talk was Raybestos. The company s GPX plates seem to be the best choice at the moment, because of their unique material and special grooved pattern that makes them run cooler when third clutches are being dragged. Raybestos told me that with this new information they ll look for options that may result in even more durability. I still have more testing to do, so my research continues. TD is the owner of Elec-Tran Diagnostics ( in Gilroy, Calif. 54 Transmission Digest
The AW55-50SN transmission
TECHNICAL TRAINING Shift Pointers Author: Jesse Zacarias Subject: Drive and Reverse engagement problems Unit: AW55-50SN (Nissan RE5F22A, GM AF33-5) Vehicle Applications: 2005 Nissan Altima Essential Reading:
More informationA Fresh Take. on Chrysler s Pressure. Figure 1
A Fresh Take on Chrysler s Pressure Boost System BEYOND THE BASICS A Fresh Take on Chrysler s Pressure by Dennis Madden members.atra.com Boost System Boost Valve Exhaust Boost Tube Figure 1 Ifind some
More informationLate Model Honda. Remember when you had a FUN WITH TRANSMISSIONS
FUN WITH TRANSMISSIONS Late Model Honda by Bill Brayton Today s late model Accords have changed; removing the unit from the car isn t always necessary to correct a shift problem. Remember when you had
More informationIf you ve had the pleasure of rebuilding
Fun with Transmissions A Quick Look at Honda Five Speeds by Bill Brayton members.atra.com www.atra.com If you ve had the pleasure of rebuilding the Honda BYBA five-speed transmission, you know this unit
More informationEasily Convert the 4L80E to Full Manual Control
Easily Convert the 4L80E to Full Manual Control by Chris Kokonis CK Performance Products Inc. They say necessity is the mother of invention. Some years ago I developed a method of converting a 4L80E to
More informationBrake master cylinder replacement
Brake master cylinder replacement 8-25-2010 I had replaced the front brake master cylinder a few years ago when it developed a bad leak, at that time, I ordered a new master cylinder from Spartan, very
More informationLX AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION TABLE OF CONTENTS
LX AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION 21-495 AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION TABLE OF CONTENTS page AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION DESCRIPTION...496
More informationFORD 6R80 UPDATES Presented by: David Chalker ATRA Technical Advisor 6R80
FORD UPDATES Presented by: David Chalker ATRA Technical Advisor Welcome To Today s Presentation Sponsored By: Any Questions Or Comments Please Send Emails To webinars@atra.com Any Questions That You
More informationFour-Wheel Drive. A Clue Discovered
Is Your Ford Four-Wheel Drive System Crazy? KEEP THOSE TRANNYS ROLLING Is Your Ford SPEAKER Four-Wheel Drive by Pete Huscher System Crazy? While working on the ATRA HotLine, I received a call from a technician
More informationZF6HP26 / 6R60. COMMON COMPLAINTS with the KEEP THOSE TRANNYS ROLLING
Common Complaints with the ZF6HP26/6R60 KEEP THOSE TRANNYS ROLLING COMMON COMPLAINTS with the ZF6HP26 / 6R60 by Pete Huscher members.atra.com Figure 1: Worn Pressure Regulator Valve In this issue of Keep
More informationby David Skora These pressure readings are based on the computer reacting to the load conditions of the vehicle. Pressures may vary
Looking inside the Volkswagen 09G 6-Speed; Part 3 Looking inside the Volkswagen 09G 6-Speed; by David Skora PART 3 I n past issues we looked at the design and operation of the VW 6-speed transmission.
More informationTiming the 9N/2N Steering Sector Gears
Timing the 9N/2N Steering Sector Gears by John Korschot - www.johnsoldiron.com (May 2010) The procedure for timing a set of steering gears in the 9/2n tractors is published in the I&T FO4 shop manual.
More informationThe E4OD and 4R100. Repeated failures are caused by. Check those Checkballs: BEYONDTHEBASICS. by Dennis Madden
BEYONDTHEBASICS by Dennis Madden Check those Checkballs: The E4OD and 4R100 Repeated failures are caused by only two types of problems: parts or technique. Now first, let s qualify failure. The failure
More informationDIAGNOSIS AND TESTING
307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Diagnostic Trouble Code Charts Diagnostic Trouble Code Chart P0102, MAF MAF concerns MAF system High/low EPC REFER to the P0103,
More informationMonitoring The Problem
Monitoring The Problem by Kerry Jonsson Every so often we run into the problem of not having a problem to solve. What do we do when we have a vehicle that is not setting codes, but it is also not running
More information2003 BMW 325xi 2.5L Straight 6 About 120K Miles; Looks Well Kept Multi Strike COP Ignition. History. Customer bought used about 3 months ago
2003 BMW 325xi 2.5L Straight 6 About 120K Miles; Looks Well Kept Multi Strike COP Ignition History Customer bought used about 3 months ago Claims since day one runs rough on cold start Sometimes MIL would
More informationFord. After rebuilding a 5R55W/S model transmission, during the road test you may encounter a are on the 2 3 shift.
112 Erratic Transmission Operation After rebuilding a model transmission, during the road test you may encounter a are on the 2 3 shift. This concern can be caused by a new solenoid pack. Over the years,
More informationBLOWN AWAY. Remember the Dodge truck we. by High Pressure STREET SMART. by Mike Brown members.atra.com
STREET SMART BLOWN AWAY by Mike Brown members.atra.com by High Pressure Figure 1 Remember the Dodge truck we talked about in the January 2015 issue? The 2003 Dodge Ram 3500 5.9 diesel? This is what happened
More informationManual Shift Transmission Fluid Change How Often Honda Civic
Manual Shift Transmission Fluid Change How Often Honda Civic 1997 Honda Civic Manual transmission drain and refill. Tools: 3/8 How To Change Honda. If your engine will rev up, but the car won't shift into
More informationWhat is it that makes that. LET S PLAY BALL Time to Shift Gears. by Lance Wiggins. Typical 4 Speed Mitsubishi
LET S PLAY BALL Time to Shift Gears Typical 4 Speed Mitsubishi by Lance Wiggins What is it that makes that grinding noise in my transmission? I just had it serviced and that noise started shortly after
More informationThere is nothing better in a
FUN WITH TRANSMISSIONS Honda Transmissions and the P0740 After-Rebuild Blues by Bill Brayton There is nothing better in a transmission shop when a Honda Accord hits the ground after a rebuild and road
More informationDiagnostic Trouble Code (DTC) Charts
SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 06/30/2009 Diagnostic Trouble Code (DTC) Charts DTC Chart **May also be
More informationELECTRIC CURRENT. Name(s)
Name(s) ELECTRIC CURRT The primary purpose of this activity is to decide upon a model for electric current. As is the case for all scientific models, your electricity model should be able to explain observed
More informationDiagnostic Procedures
Section 6 Diagnostic Procedures Learning Objectives: 1. Describe manual transmission, transaxle and transfer case component inspection and diagnostic procedures 2. Identify clutch component inspection
More informationZF6HP19/26/32 (Generation 1), Ford 6R60, 6R75, 6R80, ZF6HP21/28/34 (Generation 2)
Valve Body Identification ZF6HP19/26/32 (Generation 1), Ford 6R60, 6R7, 6R80, ZF6HP21/28/34 (Generation 2) IDENTIFICATION GUIDE Valve components differ between Generation 1 (ZF6HP19/26/32), Ford 6R60,
More informationOnce in a while an opportunity
Once in a while an opportunity comes along that compels you to share your experiences with others dealing with the same issues. In this case we had a number of issues with a late Volkswagen Beetle and
More informationMissing Mini. There are two situations we dislike extremely. The. Quick Test
The Missing Mini No, this is not a mystery about a Mini that has gone missing. This car had been off the road for a year s storage in a body shop. When it came time to return the vehicle to the customer,
More informationBest Manual Transmission Problem Shift Linkage
Best Manual Transmission Problem Shift Linkage If you have ever wanted to know how a manual transmission clutch works our from the engine to the transmission as well as to sever that link when required.
More informationVAGABOND S HANDBOOK TRANSMISSION
03/24/07 TRANSMISSION Transmission won t engage into Gear This is caused usually by too low a Voltage to get into the ECM. This unit requires a minimum of 9VDC in order to operate at all. Almost all erratic
More informationMike and Barb s 1953 MG TD
Mike and Barb s 1953 MG TD The first time I remember seeing an MG was in about 1959. I was like in 2 nd grade. I remember my dad bringing home a remote car for me. Not the remote you think of now, it had
More informationchart for this unit. Let s look at some of the gear
by David Skora recently began seeing a new 6- speed automatic transmission in some Beetle and Passat vehicles. Built by Aisan, this transmission uses the Leppeletier planetary design. All shift timing
More informationIn the last issue of Let s LET S PLAY BALL. Every code represents a perceived failure to the computer. by Lance Wiggins
LET S PLAY BALL by Lance Wiggins A Look at the 450-43LE (Aisin Seiki), Part 2 Please note: In the April issue of GEARS, Aisin Seiki was spelled incorrectly. The correct spelling is listed above. Our apologies
More informationWhy Does My Manual Car Stall When I Come To A Stop
Why Does My Manual Car Stall When I Come To A Stop I would request to my friends to refrain from given expert opinions and answers Also when you want to come to a complete stop from a decent speed how
More informationShould I Leave My Manual Car In Gear When Parked
Should I Leave My Manual Car In Gear When Parked I just wanted to know who people leave there car in first gear while there car is It's definitely saved my car a few times since my parking brake cables
More informationU660E, U660F, U760E, U760F
Transmission: Subject: Application: Issue Date: Technical Bulletin #1632 U660E, U660F, U760E, U760F Delayed or Harsh Reverse Engagements Toyota August, 2014 U660E, U660F, U760E, U760F Delayed or Harsh
More informationFor too many technicians, diagnosis. A Logical Diagnostic Procedure Saves a Fishing Trip! DRIVE ABILITY
DRIVE ABILITY by Dave Skora A Logical Diagnostic Procedure Saves a Fishing Trip! According to the repair order, the rebuilder replaced the torque converter and the converter clutch solenoid during the
More informationJATCO RE5R05A. Figure 1
LET'S PLAY BALL Controlling the JATCO RE5R05A Part 2 of 3 by Lance Wiggins So you re back for more good. In this issue of GEARS, we re going to go through the valve body, TCM and solenoids of the JATCO
More informationDESCRIPTION. Chrysler NCV3 Service Info Section 08 > Electronic Modules > MODULE, Transmission Control Information
DESCRIPTION The transmission control module (TCM) receives, processes and sends various digital and analog signals related to the automatic transmission. In addition, it processes information received
More informationDIAGNOSIS AND TESTING
307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Pinpoint Tests OSC Equipped Vehicle Special Tool(s) Transmission Fluid Pressure Gauge 307-004 (T57L-77820-A) Special Tool(s) MLP-TR
More informationTechnical Bulletin Listing
Transmission Bulletin # # Pages Subject Technical Bulletin Listing January, 2007 January U140E, U140F 829A 2 Sprag Rotation V4A51 1054 1 No Power Above 3500 RPM 4T60E 1055 1 Neutral/Shudder During the
More informationAn Actual Driving Lesson. Learning to drive a manual car
An Actual Driving Lesson Learning to drive a manual car Where are the controls that I might have to use in my driving: Knowing where the controls are, and being able to locate and use them without looking
More informationFORD 6F50, 6F55 ZIP KIT
FORD 6F0, 6F ZIP KIT PART NUMBER 6F0-ZIP QUICK GUIDE Parts are labeled here in order of installation. See other side of sheet for details on Zip Kit contents. CAUTION: Ensure shuttle valve is installed
More informationAre you as confident and
64 March 2007 BY BOB PATTENGALE Although Mode $06 is still a work in progress, it can be used to baseline a failure prior to repairs, then verify the accuracy of the diagnosis after repairs are completed.
More informationFigure 1: Valve housing smooth vs. o-ring groove
If you are driving an older Corvette, and by that I mean a C2 or C3, it will eventually get to a point where the Power Steering Control Valve (PSCV) will leak and require attention. In 2002, I had to repair
More informationTechnical Bulletin # 1251
Transmission: Subject: Application: Issue Date: CD4E TCC Slip Code Diagnosis Ford, Mercury and Mazda May 2009 CD4E TCC Slip Code Diagnosis Once the check engine light illuminates, the transmission will
More informationElectrical Testing in the Operating Room; Part 6
DOCTORDOCTOR It hurts when I shift! by Randall Schroeder Electrical Testing in the Operating Room; Part 6 IIn the operating room, doctors are faced with precise test procedures that are challenging and
More information2002 Ford Explorer AUTOMATIC TRANSMISSIONS' '5R55W/S Diagnosis 2002 AUTOMATIC TRANSMISSIONS. 5R55W/S Diagnosis
2002 AUTOMATIC TRANSMISSIONS 5R55W/S Diagnosis APPLICATION WARNING: Vehicles are equipped with Supplemental Inflatable Restraint (SIR) system. When servicing vehicle, use care to avoid accidental air bag
More informationSTARTER CIRCUIT TROUBLESHOOTING
2000 Honda Accord EX Sedan V6-3.0L Vehicle > Starting and Charging > Starting System > Starter Motor > Testing and Inspection > Component Tests and General Diagnostics STARTER CIRCUIT TROUBLESHOOTING Starter
More informationI cannot believe it has been so long since my last update. A lot has happened and I will try to bring everyone up to speed. First of all, I had my
I cannot believe it has been so long since my last update. A lot has happened and I will try to bring everyone up to speed. First of all, I had my left knee replaced about 5 weeks ago. Needless to say
More informationPRESEASON CHASSIS SETUP TIPS
PRESEASON CHASSIS SETUP TIPS A Setup To-Do List to Get You Started By Bob Bolles, Circle Track Magazine When we recently set up our Project Modified for our first race, we followed a simple list of to-do
More informationFORD 6F50, 6F55 ZIP KIT
FORD 6F0, 6F ZIP KIT PART NUMBER 6F0-ZIP QUICK GUIDE Parts are labeled here in order of installation. See other side of sheet for details on kit contents. CAUTION: Ensure shuttle valve is installed with
More informationDIAGNOSIS AND TESTING
307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Transmission Connector Layouts Connector Reference and Terminal Readings Powertrain Control module (PCM) 1 Pressure control solenoid
More informationFuller Automated Transmissions TRDR2500
Driver Instructions Fuller Automated Transmissions TRDR2500 July 2007 RTO-10910B-DM2 RTO-12910B-DM2 RTO-14910B-DM2 RTO-16910B-DM2 Warnings & Cautions Warnings & Cautions WARNING Read the entire driver
More informationI think that this is an important time for everyone to see how all of the pieces are going together in just one component. Pictures #1, #2, and #3
I think that this is an important time for everyone to see how all of the pieces are going together in just one component. Pictures #1, #2, and #3 are of the finished distributor. For those of you who
More informationFuller Automated Transmissions TRDR0082
Driver Instructions Video Instruction Available Instructional videos are available for download at no charge at roadranger.com Videos are also available for purchase. To order, call 1-888-386-4636. Ask
More informationMedia Number -SENR Publication Date -01/10/1977 Date Updated -12/10/2001
- - 55, 56, 57, 58 & 59 TOWING WINCHES Page 1 of 21 Testing and Adjusting 55, 56, 57, 58 & 59 TOWING WINCHES Media Number -SENR7217-01 Publication Date -01/10/1977 Date Updated -12/10/2001 Testing And
More informationFuller Heavy Duty Transmissions. Video Instruction Available. Fuller Heavy Duty Transmissions TRDR3349 September 2007
Fuller Heavy Duty Transmissions More time on the road Video Instruction Available Instructional videos are available for download at no charge at roadranger.com Videos are also available in DVD format
More informationCustomer Open Date Hours Work Order Notes /9/2018 0:
4SN00509 Last SMU: 21294 H Customer Open Date Hours Work Order Notes 29041 7/27/2018 0:00 21268 3021405-01 3021405-02 COMPLAINT: STEERING COLUMN TILT DOES NOT WORK CAUSE: PIN MISSING CORRECTION: REMOVED
More informationValve Body Rebuild Tips & Techniques
Ford 4r44e, 4r55e, 5r44e, 5r55e zip Kit PaRT NUMBER 4r44e-5r55e-zip Installation & TESTING BOOKLET Torque Specifications Band Adjuster Lock Nut 35 to 45 ft-lb Transmission Oil Pan Bolt 115 to 133 in-lb
More information46RE, 46RH, 47RE, 47RH ZIP KIT
46RE, 46RH, 47RE, 47RH ZIP KIT PART NUMBER 46-47RHE-ZIP QUICK GUIDE Parts are labeled here in order of installation. See other side of sheet for details on Zip Kit contents. installation Diagram 7 1 Separator
More informationTransmission Electronic Control System
SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 05/23/2008 Transmission Electronic Control System Electronic System
More informationMercedes Benz has introduced
THE ART OF THEORY The Strategy of the 722.9 (NAG2) by Hank Blair members.atra.com www.atra.com Mercedes Benz has introduced the 5 th generation electronically controlled transmission, called the 722.9
More informationInstalling the Dan-Marc and Pingel setup.
Installing the Dan-Marc and Pingel setup. This is an alternative to the OEM vacuum petcock. It's the setup I use and feel more comfortable with it. Many still like the OEM vacuum petcock and they can continue
More informationDiagnostic. Enlightenment. The Path to
The Path to Diagnostic Enlightenment BY JORGE MENCHU If you don t know where you re going, any road will take you there. When it comes to automotive troubleshooting, the right road is the shortest path
More informationDIAGNOSIS AND TESTING
307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Special Testing Procedures Special Tool(s) Air Test Plate, Transmission 307-405 Transmission Fluid Pressure Gauge 307-004 (T57L-77820-A)
More informationAUTOMATIC CLUTCH Models
AUTOMATIC CLUTCH 1940 Models Source of this material is from 1940 Series, Issue 4, January 1940 Hudson Service Magazine AUTOMATIC CLUTCH 1940 MODELS The automatic clutch installation and adjustment procedure
More informationChronic Valve Body Wear
Chronic Valve Body Wear by Larry Frash Every penny I ve earned in my life has been from the automotive industry. For that, I am thankful. If the manufacturers made a perfect vehicle, all we could hope
More informationIn the operating room, transmission
DOCTOR DOCTOR It hurts when I shift! REPRINT FROM MARCH 2005 SEE PART 2 ON PAGE 24 by Randall Schroeder In the operating room, transmission surgeons are often faced with split-second decisions regarding
More informationOnce again, another four weeks have gone by and I am quite sure everyone is tired of me wondering where the time has gone. To say that everything
Once again, another four weeks have gone by and I am quite sure everyone is tired of me wondering where the time has gone. To say that everything around the shop has been a little chaotic during this time,
More informationShift Solenoid B (SSB) and Shift Solenoid D (SSD) Inverse Proportional VFS 2761
Item Description 1 Shift Solenoid A (SSA) Variable Force Solenoid (VFS) 2 Shift Solenoid C (SSC) VFS SSB and SSD use inverse proportional operation. As the current from the PCM decreases, the pressure
More informationPERKINS Fitting new rear oil seal and crank case gaskets
PERKINS 4108 Fitting new rear oil seal and crank case gaskets Near the end of this summer the 24 year old Perkins on my Morgan 384 decided to misbehave. First the solenoid on the starter motor, then the
More information1986 Rear Disk Brake Upgrade. All hard lines mounted to the rear axle with mounting screws. 1/4" fittings
1986 Rear Disk Brake Upgrade Being well prepared for a project of this size is the key to success. I thought I was well prepared by doing a lot of research and getting all of the required parts before
More informationLincoln Mark VII T5 Swap Version submitted by 5.0 bird
Lincoln Mark VII 1984-1989 T5 Swap Version 20070611 submitted by 5.0 bird I've decided to make an article to assist with the T5 swap for the 84-89 Mark VIIs, since I was just in there because my DOA didn't
More informationRemoving your Two-blade Hartzell HC-12 (?) 20 prop off a Franklin Engine (Or How do I change the prop cylinder O-rings! )
Removing your Two-blade Hartzell HC-12 (?) 20 prop off a Franklin Engine (Or How do I change the prop cylinder O-rings! ) If you are having oil leaking around the propeller piston/cylinder assembly and
More informationDTC P1811 Maximum Adapt and Long Shift
2000 Buick Century DTC P1811 Maximum Adapt and Long Shift Circuit Description The transmission pressure is modified by an adaptive modifier which controls the shift execution time. This test checks the
More informationSome tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000
Some tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000 Last change 2013-Oct-11 I bought Haynes manual for a starter. That s something well worth it s cost I believe.
More informationModule 12 Throttle Position (TP) Sensor
Module 12 Throttle Position (TP) Sensor Author: Grant Swaim E-mail: sureseal@nr.infi.net URL: www.tech2tech.net Phone: (336) 632-9882 Fax: (336) 632-9688 Postal Address: Tech-2-Tech Website PO Box 18443
More informationTechnical Bulletin Listing 2010
Technical Bulletin Listing 2010 January, 2010 Transmission Bulletin # # Pages Subject January Allison LCT 1000 1300 1 Sets P0872, No 4th, 3rd Gear Start 4L80E 1301 4 Shift Shuttle/No Line Rise RE4F04A
More informationEDITOR'S NOTE: This article replaces "Use PGM FI Data List to Help Troubleshoot Inoperative A/C," issued in June 2012.
2001 Honda Civic 1.7L Eng LX TROUBLESHOOTING AN INOPERATIVE A/C TECHNICAL SERVICE BULLETIN Reference Number(s): 13 080J, Date of Issue: August, 2013 HONDA: '00 and later models with A/C APPLIES TO: '00
More informationSUBJECT: ALLISON MODEL MD3060 TRANSMISSION ELECTRONIC CONTROL MODULE (ECU) MALFUNCTION. ECU + Cal Assy ECU Module P/N S/N
BY: Brent Ostendorff March 6, 2010 SUBJECT: ALLISON MODEL MD3060 TRANSMISSION ELECTRONIC CONTROL MODULE (ECU) MALFUNCTION. ECU + Cal Assy 29511270 ECU Module P/N 29514527 S/N 2414673 VEHICLE: 1994 MONACO
More informationLast month we looked at the
TECHNICAL TRAINING Up To Standards Author: Mike Weinberg, Contributing Editor Subject Matter: Internal components Unit: Tremec TR6070 Vehicle Application: 2014 Corvette Stingray Inside the Tremec TR6070
More informationVW 09G. Bumping. Welcome back to another TALES FROM THE BENCH. TCC Valves. by Jarad Warren members.atra.com
Bumping VW 09G TALES FROM THE BENCH Bumping VW 09G by by Jarad Warren members.atra.com Welcome back to another addition of Tales from the Bench. In this issue of GEARS, we re going to look at a 2005 Volkswagen
More informationRodeo Roundup. When working with. by Mike Baird
by Mike Baird Rodeo Roundup Figure 1 When working with local transmission shops I occasionally get the opportunity to get my hands on a problem vehicle. This particular problem was with a 1997 Isuzu Rodeo
More informationK6JRF's Page formerly W6FZC
K6JRF's Page formerly W6FZC My Mercedes Benz S500 Coupe (Updated: Nov 9, 2004) Analyze and Troubleshoot "Check Engine" MIL and Electronic Control Units (ECU)! Seat Belt Extender About one month ago, the
More informationRetro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010
More informationMount polished. Frame layout
November 2014 Brandt made a full mockup of the seat in vinyl to make changes and have patterns for the seats. We did some adjustments the height to lower the seats as much as possible. I was unable to
More informationDI 244 DIAGNOSTICS AUTOMATIC TRANSMISSION DIB30 01 PRE CHECK
DI244 DIAGNOSTICS PRECHECK DIB3001 1. DIAGNOSIS SYSTEM (a) Description When troubleshooting OBD II vehicles, the only difference from the usual troubleshooting procedure is that you connect to the vehicle
More informationE4OD/4R100. Check Ball Identification and Symptom Chart. Early 1989 E4ODs The first E4OD had 16 checkballs.
110 FORD Check Ball Identification and Symptom Chart Repeated failures are caused by only two types of problems: parts or technique. If a part is causing the failure, it should be no surprise that using
More informationNo Drill Modern Gas Shock Installation on a 1931 Ford Model A Coupe
No Drill Modern Gas Shock Installation on a 1931 Ford Model A Coupe Today we are not going to cover something new but just a little insider info in to what we do during our time off at Apex Tool Company.
More informationWHAT IS MANUAL AND AUTOMATIC TRANSMISSION IN CARS
20 April, 2018 WHAT IS MANUAL AND AUTOMATIC TRANSMISSION IN CARS Document Filetype: PDF 122.86 KB 0 WHAT IS MANUAL AND AUTOMATIC TRANSMISSION IN CARS Are you once again confused to buy an automatic transmission
More informationConverting an Old 84 VW Rabbit GTI into an Electric Car
Introduction: Converting an Old 84 VW Rabbit GTI into an Electric Car By James Keele May 26, 2012 Over a time period of about four years, I actually converted two gas powered cars to electrical powered
More informationToyota introduced the U250E 5-
A Closer Look at the Toyota U250E STREET SMART A Closer Look at the Toyota U250E by Mike Brown Toyota introduced the U250E 5- speed automatic transmission in the 2005 Camry with 2AZ-FE engines. It s a
More informationThere is hence three things you can do - add oil, adjust the temp that the clutch begins to engage, or do both.
As most of you may be aware, I have been doing a lot of research lately on our cooling system in the 80's including the fact that we have a dead spot on the OEM temp gauge which prompted me to not rely
More informationSECTION 1 7 OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake
SECTION 1 7 OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch.............................................. 114 Automatic transmission.....................................
More informationTECH BACK TO THE STREET, PART 2
We continue to puzzle together the drivetrain for our 71 Camaro with a 4L60E automatic from Level 10 Transmission systems. By Mike Ficacci Photos by the author After making boatloads of horsepower and
More informatione36_remove_clutch_pedal_slop
http://www.unofficialbmw.com/e36/drivetrain/.html Page 1 of 12 UnofficialBMW.com [Top Links Search FAQ Parts Used Cars FTP Images New Bulletin Board Garage] Unofficial Homepages: [02 E12 E28 E30 E32 E34
More informationPinpoint Tests OSC Equipped Vehicle
SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 11/19/2008 Pinpoint Tests OSC Equipped Vehicle Special Tool(s) 73 III
More informationTable of Contents INTRO
GENERAL ALL Wheel Drive Systems General System Overview...2 Transfer Coupling...3 Diagnostics, Tire Wear, Codes...4 Rolling Circumference Test...5 Getrag 760 T-Case Introduction and Service Information...6
More informationFourth Grade. Multiplication Review. Slide 1 / 146 Slide 2 / 146. Slide 3 / 146. Slide 4 / 146. Slide 5 / 146. Slide 6 / 146
Slide 1 / 146 Slide 2 / 146 Fourth Grade Multiplication and Division Relationship 2015-11-23 www.njctl.org Multiplication Review Slide 3 / 146 Table of Contents Properties of Multiplication Factors Prime
More informationFourth Grade. Slide 1 / 146. Slide 2 / 146. Slide 3 / 146. Multiplication and Division Relationship. Table of Contents. Multiplication Review
Slide 1 / 146 Slide 2 / 146 Fourth Grade Multiplication and Division Relationship 2015-11-23 www.njctl.org Table of Contents Slide 3 / 146 Click on a topic to go to that section. Multiplication Review
More information