How to change Swirl Flaps, on Diesel BMW
|
|
- Juniper Howard
- 5 years ago
- Views:
Transcription
1 How to change Swirl Flaps, on Diesel BMW I am now going to show you how i did it on my car. May'sedition of Total BMW (still in WHSmiths) did a cover on how to change and modify Swirl flaps on a 330d engine, so if you can get hold of that copy, itmay be more helpful than this guide. You will need a fairly decent tool collection, something that will have different type head fittings and bits that can fit in tight areas. OK, before we start i need to say the following: *****I have performed the maintainace myself and i am comfortable with my ability to do so and i can not be held responsible if you damage your vehicle in an event to follow my guide.***** I will be using some information from other post which i have obtained go-ahead to use. Make sure you do not use excessive force and try to keep bolts and screws close as you dont want them falling down to the florr pan and waste time and patience trying to look for them
2 1. Disconnect the battery: On the left side of the engine will the battery connector. You will need a 19mm socket to take the main bolt off:
3 And then a 10mm socket to take the smaller bolt off: Pull the smaller wire through the hole and leave for later.
4 2. Removing all the engine panels: What i did first was to remove the pollen filter panel in-front of the windscreen: Undo the 3 clips, one on each side and one on the front. Once undone, they will spring up and then you can lift the panel:
5 Pull the panel out and take the filter out:
6 You will see 4 T30 (Torx30) screws which will need to be unscrewed.
7 Once done so, unclip the 2 black clips holding on the the panel. Put you finger underneath and lift slightly and they should upclip.
8 If you to, you can seperate the 2 holders running across. Simply slide the front holder to the left and it will unclip: Once the holders are off, you can lift the panel out:
9 Where the last panel was mounted, you will see another panel held in by 2 T30 screws either side and 1 plastic clip on the right side of the panel. Unscrew the 2 screws (first pic) and softly unscrew the clip (pic 2) and try to pull the panel away being careful not to drop the clip: From there, carefully lift the panel out as there is a metal clip at the bottom of the panel which could damage something if your not too careful.
10 Now for the front and rear engine covers. In the Front Cover there are 5 bolts (5mm hex) holding the cover on. 2 at the front, 2 at the back and one on the right side near the coolant cap.: I didnt take any pics of taking the rear cover sorry but it is simple. There a 3 5mm hex bolts, 2 on top of the cover and the other down the right rear side. You will also need to need to unclip and cable as well.
11 3. Taking the manifold out: When you have taken the cover out, you will see the a string of cables mounted down by 3 8mm star socket bolts. Take these out like so:
12 once out, unplug the 4 connectors: Pull them to one side and leave for later. You will now need to take the bolts out of the manifold. There are 8 10mm bolts which need to taken out:
13 Once undone, see where i now have the socket in picture 2, there are 5 thin 10mm nuts which have to be undone. Be careful not to drop them and if you can have a magnet nearby:
14 When you have done that, you will now need to take the EGR valve off. You can clean this at the same time but down to you. The EGR valve is at the front right part of the manifold and looks like:
15 On the side of the EGR valve is a small pipe which can be taken off easily by hand or with the assistance of a small flat head scredriver: You might want to put some masking tape around it and write down where you took it off. You will need a T20 head to unscrew the cable mount:
16 You will need a flat head screw driver to undo the fron jubilee clip: Pull the clip back and unscrew the other but uncrew it completely so it can be moved past the bend:
17 With the screwdriver, carefully prise the large pipe away:
18 Using the 5mm hex head, there are 4 bolts holding the EGR valve to the manifold. The top 2 are easy but be careful not to drop the bottom 2: When the bolts come out, the EGR valve should look like this:
19 Put to one side and go back to the manifold. Where the dipstick it, there is a 8 or 9mm bolt holding the bracket in place, undo it but be warned, its niggly:
20 Behind the dipstick mount there will be a cable mounted to the manifold, unclip it from underneath and pull the cable out: Around the back of the manifold, there is another connector which is grey which will need disconnecting. Make sure you reconnect it when rebuilding as you car will not have no power (ask Slowtech) From here, its a b*stard!! Im not going to lie but if you need a brew, go and get now as your patiences is definately needed.
21 Now that you are all refreshed, you need to lift the manifold up, it wont come out as the are 2 valves/sensors mounted underneath. If you can unclip the valve, that is better, but if like me you can unclip everything and remount later: From the pictures, each valve has a connector and 2 pipes. I pulled the pipes off and took the metal pins out to disconnect the connectors. Be careful with the clips as you dont want to loose them!!
22 Once off, you should be able to lift the manifold off, turn it over: At this point i managed to unclip the 2 valves and reconnect them to the engine as i thought it would easier to remount. On the manifold will the the rail that controls the valves, on the right side, light prise the rail fron its clips:
23 Using the T20 head, unscrew the 2 screws: Once done, pull the rail and motor off being careful not to break it. You should be ablt to see the flaps now, unscrew the 2 screws either side:
24 And prise away the flap: Once out they will look like this:
25 Mine where in good condition but they may not be the cause with others. With the caps, they did not come with the rubber seals so i prised the old ones off and cleaned them up and mounted them on the caps:
26 And then, once done, screwed back in: and reversed the process to rebuild the engine. Mine runs as it was and i am now happy that i done it, especially by myself. I hope you found this useful and i hope it serves you well. Cheers
This guide will explain how to remove the old springs from the car and replace them with lowering springs.
fubar Guide: Fitting lowering springs to the Mk2 Clio The method described below worked for me. I am not saying it is the only method to complete the task. I will not accept any responsibility for damage
More informationAt Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job.
At Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job. My enormous thanks to forum members, particularly glorfindel, for their advice when
More informationFord Racing BOSS 302 Engine Oil Cooler (11-14 GT)
Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets
More informationBEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta).
BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta). Based on the procedure published by Volkswagen, but modified for the "average" shadetree mechanic. Some special
More informationOEM Cruise Control Installation in GMC/Chevy NBS trucks
OEM Cruise Control Installation in 99-02 GMC/Chevy NBS trucks May 2008 ~ Rampage_Rick Having just installed factory cruise control in my 00 Sierra, I thought I d share the fun. I followed the steps outlined
More informationHow To: Thermostat change - D8 V6 194bhp
How To: Thermostat change - D8 V6 194bhp Firstly, take off the Air Filter hoses and connectors and lift off. This leaves you with this workable space... I started with taking the two bolts out of the cable
More informationAudi A8 ( ) MMI swivelling unit repair manual
Audi A8 (2003-2007) MMI swivelling unit repair manual Tools which you will need: two pcs screwdriver (any kind, for vent removing ) (you can cover the metal part with any tape to prevent making scratches
More informationDisco 3 Clock Spring / Rotary Coupler replacement
Disco 3 Clock Spring / Rotary Coupler replacement I recently had to change my Clock spring and thought some folks may find it helpful to see what it entailed. I did lots of reading around but couldn t
More informationPDC RETROFIT INSTALLATION By Kevin
1 PDC RETROFIT INSTALLATION By Kevin Kshek369@hotmail.com 1 These instructions are intended to help those who chose to do this retrofit by showing you what you are in store for and to give you some instructions
More informationPCV System Repair on a Volvo 5-cylinder
PCV System Repair on a Volvo 5-cylinder by jblackburn» Tue Apr 06, 2010 12:28 am As any engine runs, there are gases from the top of the cylinders that escape past the piston rings and into the crankcase
More informationW123 Transmission Vacuum Modulator Adjustment DIY - measure it the 'right' way
W123 Transmission Vacuum Modulator Adjustment DIY - measure it the 'right' way Why do you need to do this?: You need to do this to properly check the internal hydraulic pressure of the transmission, either
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationFitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE
Part Number DA1112 Fitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE You do this modification at your own risk. Britpart won t be held responsible for what is written
More informationHow To: Fit an enclosed induction kit to the V6
How To: Fit an enclosed induction kit to the V6 As a couple have done this I thought I'd have a go, but do a write up at the same time. Here's a quick summary of the equipment you'll be needing: 1 x Universal
More informationM62 Alternator Removal / Replacement (Water Cooled)
M62 Alternator Removal / Replacement (Water Cooled) Pre-Steps 1. Disconnect Battery Positive lead 2. Charge Your Battery with battery charger to full charge (So you new alternator wont have to work as
More informationInstalling Custom Puddle Lamps 2009 Subaru Forester
Installing Custom Puddle Lamps 2009 Subaru Forester By John Perkins This guide will assist you in installing a set of LED puddle lamps on a 2009 Subaru Forester. This is NOT using the $150 Subaru kit.
More informationThere was some debate whether or not there was a write up, with Pictures, for replacing the ignition switch.
Replacing the Ignition Switch - Step by Step with Pictures. http://forums.audiworld.com/showthread.php?p=18927576 (Corey 02ALMSTT) (With updates/corrections by Dave F.) February 1, 2013 (I = Corey, mostly)
More informationSTEPS FOR REMOVING REAR ASHTRAY & CUP HOLDER, CENTER ARMREST, E- BRAKE CONSOLE, FRONT ASHTRAY, LOWER CENTER CONSOLE AND GLOVE BOX
Please give credit where credit is due! This DIY was completed ENTIRELY by the hardest working VW Vortex moderator on the site!! Gary Thompson, Ph.D. - vortex ID VGRT6, email address vgrt6@yahoo.com. Please
More informationFitting the Bell Auto Services (B-A-S) TDV6 EGR Blanking Kit to a 2006 model Discovery 3 TDV6 HSE
Fitting the Bell Auto Services (B-A-S) TDV6 EGR Blanking Kit to a 2006 model Discovery 3 TDV6 HSE Before I describe how I did this, I must first thank other members of the Disco3.co.uk forum (namely J,moore
More informationList of parts needed below. Tools needed
1 BMW 645 Coolant leak repair (Cap with Seal Repair and Expanding Coolant Pipe Installation w Pics) By Michael R. Brown (Estimated time to complete the job is 6-8 hrs) List of parts needed below. BMW PART
More informationThis is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX
Adjusting the valve clearance on a 2L V6 FTO engine This is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX Disclaimer: This guide is to assist you
More informationPlease use this How to in conjunction with the workshop manual pdf on the same subject.
Please use this How to in conjunction with the workshop manual pdf on the same subject. The workshop manual is a decent guide but fails to mention a few things which would hinder progress and probably
More informationBHW Engine Coolant Temperature Replacement
BHW Engine Coolant Temperature Replacement NEVER perform this procedure on a hot engine. Parts: 059 919 501 A dual temperature sensor 032 121 142 retaining spring N 903 168 02 sensor round seal N 905 216
More informationPLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!!
JDM power folding mirror switch install into stock USDM harness. By: Greg L., Zeke21 on twinturbo.net PLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!! This is how I was able to get the
More informationInstallation instruction do88 Performance Radiator for Volvo S60 V70 XC70 S
Installation instruction do88 Performance Radiator for Volvo S60 V70 XC70 S80 00-09 1. This instruction shows how to replace the OEM radiator with do88 performance radiator. At this type of installation
More informationSingle Barrel Shotgun HPFP Install Guide
Single Barrel Shotgun HPFP Install Guide Thank you for purchasing the VTT Single Barrel Shotgun HPFP upgrade kit! PLEASE READ THE ENTIRE GUIDE BEFORE BEGINNING INSTALLATION! The first thing you should
More informationJRSC + BBK Install on SVTF. Neil A. Shah medicnas on focaljet September 2006
JRSC + BBK Install on SVTF Neil A. Shah medicnas on focaljet September 2006 ECU up here. When removing make sure the smaller bundles of wires don t get wrapped around the bottom edge and break - this almost
More informationApologies for the absence of pictures during the removal. I was just getting on with it and completely forgot about taking pictures.
Please note that this is exclusive to a non-sunroof vehicle. Those with sunroofs will have additional fittings/fixings to deal with, of which I have no knowledge of. Apologies for the absence of pictures
More informationYOU MAY WANT TO FIRST TRY TO LOOSEN THE FILTER HOUSING
2005 XC90 Tune-up (5-cyl) Including: Oil Change - Spark Plugs - Fuel Filter - Cabin Filter First off - let me say that I am an amateur (at best) mechanic, and I claim no responsibility for whatever you
More informationBMW E46 Convertible Hydraulic Line #23 Replacement Guide Created by taylor192 of E46Fanatics.com
BMW E46 Convertible Hydraulic Line #23 Replacement Guide Created by taylor192 of E46Fanatics.com BMW E46 Line #23 Replacment Guide, page 1 of 23 Background: Line #23 runs from the valve block on the driver's
More informationAutomatic trunk lid retrofit BMW F10 Bj.2011 by laser21 bimmerfest.com
Automatic trunk lid retrofit BMW F10 Bj.2011 by laser21 bimmerfest.com lukasko@gmail.com This is a short guide to help you retrofit the option SA316 - automatic trunk lid mechanism into your F10. That
More informationwhat you need to do is hit the taper housing as hard as you can with your hammers AT THE SAME TIME and at a slight angle, what will happen is you
first things first, get the car on axle stands and the wheels off. Open the bonnet to let more light through to the area in which you'll be working. The following guide shows the passenger side being done
More informationFord Super Duty 5.4L Spark Plug Change F250 4x4 XLT Sport Crew Cab
1 of 32 Ford Super Duty 5.4L Spark Plug Change 2004 F250 4x4 XLT Sport Crew Cab Back to 2004 F250 Main Page Click Here for a PDF version of this article At close to 100k miles, I figured it was time for
More information2000 Mr2 Spyder Seat Cover Replacement Project
2000 Mr2 Spyder Seat Cover Replacement Project Tool List: Plastic Trim Tool, Hog Ring Pliers, Medium or Heavy Duty Wire Cutters, 12mm socket, 14mm Socket, Ratchet, Extension, Flat Head Screwdriver & Gloves
More informationReplacing the Vacuum Servo on 700/900 with ACC/ECC Double-Acting Servos. [Procedure from Dick Riess, to whom thanks are given; some notes from Dan]
Replacing Vacuum Servos in ACC/ECC-Equipped 700/900 Cars FAQ Home Volvo Maintenance FAQ for 7xx/9xx/90 Cars HVAC Home OEM Manual Procedure for Replacing Vacuum Servos. See the FAQ file for a large.pdf
More informationX-Type w/ non-premium sound amplifier installation instructions
X-Type w/ non-premium sound amplifier installation instructions 1. Pull radio from dash (see Radio Removal Instructions ) 2. Disconnect wiring harness from back of radio by pushing in tab on plug and pulling
More informationC4 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions
C4 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions Ok, let's start with taking the radio bezel dash area off first. Here is what the OEM radio looks like, and the points you
More informationNHP Exhaust Boxster Muffler V2 Installation Instructions and Tech Tips.
NHP Exhaust Boxster Muffler V2 Installation Instructions and Tech Tips. Thank you for purchasing your new Porsche 986 NHP Exhaust System, below you will find installation instructions to help you complete
More informationThis is what we are trying to create in the steps below
You will need: (1) Some 3/4 aluminium or steel flat bar (+/- 1 foot) (2) About 12 of 3 Aluminium or steel tubing. (2) Piece of 3X3 silicone hose and 2 hose clamps (3) 1 K&N (or similar) high flow filter
More informationInstalling the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version)
Installing the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version) September 2, 2018 Tools needed: Wireless charger upgrade kit Plastic trim tools 7 mm nut driver Background: I purchased the
More informationDIY: Shiver Valve Check, Illustrated
DIY: Shiver Valve Check, Illustrated By Petemoss, AF1 Forum Tools needed: 4mm allen wrench to remove all the fairing pieces 2.5mm allen wrench to remove battery holder 5mm allen wrench for valve cover
More informationE46 FUEL FILTER CHANGE Pics from CI
1 of 10 5/3/2010 1:48 PM E46 FUEL FILTER CHANGE Pics from 2001 330CI Bellows Expansion Joints Metal Bellows Expansion Joints in Every Style from Flexicraft www.flexicraft.com/metal_bellows Ask a BMW Mechanic
More informationChanging the Struts on a WK Jeep CRD
Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationIn summary, the procedures includes removal of the belly pans, draining of the engine block, draining of the radiator, coolant mixing and refilling.
COOLANT DRAIN AND CHANGE PROCEDURE Recently, there was a request for a picture guide for draining/changing coolant (Robot808 and James-man) and since I was going to do this operation on Idaho (88), I took
More informationBMW 528i E39 Sunroof Repair
These instructions will help guide you through the repair process for broken sunroof control rails on an E39 chassis. Before I get started, I want to give a shout-out to a couple people who also posted
More informationHow to remove and refit the Steering Wheel. 1. Start by getting the front road wheels straight and engage the steering lock
How to remove and refit the Steering Wheel By 7T5 and Pondweed Important, during this job do not operate the door locks or remote locking button at any time as doing so can make your central locking inoperative.
More informationW C-230 Kompressor Sports Sedan 1.8l Thermostat Replacement & Antifreeze flush
W203 2003 C-230 Kompressor Sports Sedan 1.8l Thermostat Replacement & Antifreeze flush First, I have to thank everyone who has contributed to the MBworld.org forums without you; I would not have gotten
More informationWheel Bearing Replacement Passat TDI
Rear Bearing/hub assembly replacement This is a fairly straight forward process. Pictures are not necessary for most of this procedure for a person with skills to do this repair. Anyone who thinks they
More informationRear Speaker replacement.
Rear Speaker replacement. First off you need the right rear speakers. The easy bit is 6x9 and better than a 15W paper cone, the difficult bit is getting a mounting depth under 74mm. Or to be more precise,
More informationBMW 3 Series Oxygen Sensor
1984-1991 BMW 3 Series Oxygen Sensor Replacement Replace an old oxygen sensor on your E30 for better gas mileage. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION
More informationOkay! In starters sorry about my bad english hope you understand at least some of this stuff what i m writing about!
------------------------------------------------------------------- Okay! In starters sorry about my bad english hope you understand at least some of this stuff what i m writing about! This guides meaning
More informationBMW 2002 M42 Swap Notes-THIS IS NOT FINISHED
BMW 2002 M42 Swap Notes-THIS IS NOT FINISHED This document is to help those that want to install an m42 into a BMW 2002. It is based around an e30 engine, trans, and wiring. You can use the e36 block/head/wiring
More informationRe-building a Caliper
Re-building a Caliper by Leslie Henson The pistons in the calipers on the 90 are in very poor condition, and although the brakes work ok, it plays on our mind that the pistons are badly corroded, and it
More informationSome tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000
Some tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000 Last change 2013-Oct-11 I bought Haynes manual for a starter. That s something well worth it s cost I believe.
More informationBBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt)
BBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt) Install Time: Approx. 8-10 hrs Parts Needed: BBK Long Tube Headers Shorty mid pipe X/H O2 wiring harness extensions Hi-temp thread locker Tools Required:
More informationVW SCIROCCO TWINTERCOOLER INSTALLATION INSTRUCTIONS
VW SCIROCCO TWINTERCOOLER INSTALLATION INSTRUCTIONS Tools needed: T25 torx driver Small flat head screwdriver 12mm & 13mm socket, with ratchet Dremel or similar with cut off disc Large Phillips screwdriver
More informationH31 BOOSTER REBUILD & MASTER CYLINDER
2010 1991 BMW 750iL George Fontes gajfontes@yahoo.com H31 BOOSTER REBUILD & MASTER CYLINDER Rebuild hydraulic booster and replace Master Cylinder. Page 1 of 16 Master Cylinder Removal & Brake Booster Rebuild
More informationBMW 3 SeriesE90 - E93 Factory Alarm Install
Instructions on a BMW 3 Series Factory Alarm Install. Written By: Danielle 2017 guides.drivediy.com Page 1 of 9 INTRODUCTION Tips on how to install a BMW 3 Series Factory alarm. Credit: CC 330i[E90Post.com
More informationGenuine Corvette Accessories Carbon Fiber Radio Surround Installation Instructions for Corvettes.
Genuine Corvette Accessories Carbon Fiber Radio Surround Installation Instructions for 2005-2007 Corvettes. Difficulty: 3 out of 5. Time: Plan on about 1 hour. The tools used are: A small flashlight A
More informationPrius XM Radio Installation Instructions. Eddie Bell
2004-2005 Prius XM Radio Installation Instructions By Eddie Bell www.metrotpn.com 1 Let me begin by saying this is an easy but time consuming job. Set aside a few hours of your time for the install. If
More informationAamir_bt The legend..
Aamir_bt The legend.. How to do timing on a 4XE1-W (DOHC) engine. well i decided to to a write up for DOHC timing since there was only the SOHC written up, and i had to do a timing belt on my stylus anyways,
More informationTurner M50 Manifold Adapter Install. April 26, 2012
April 26, 2012 Models: 1996-99 E36 328i/M3; 1997-98 E39 528i, 1997-98 Z3 2.8, 1998-2000 MZ3 S52 Product(s): Turner M50 Manifold Adapter Kit Subject: Installation Guidelines and Tips This guide will aid
More informationAnglefire s Guide to Radiator Replacement
Land Rover Discovery 3 Anglefire s Guide to Radiator Replacement Mark Colston WWW.DISCO3CLUB.CO.UK August 2011 Version 1.0 Copyright Mark Colston Change Record. DATE Revision Update Notes Made By August
More informationTools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve.
Before installing a shift kit, be sure the transmission is in good operating order. If your transmission is making noises, slipping, shifting bad or the fluid looks brown or smells burnt, take the transmission
More informationProjector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation
Projector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation Now it is time to remove the headlights! Obviously you have to open the hood to do this. 100_3630.jpg
More informationVW SCIROCCO R TWINTERCOOLER INSTALLATION INSTRUCTIONS
VW SCIROCCO R TWINTERCOOLER INSTALLATION INSTRUCTIONS Tools needed: T25 torx driver Small flat head screwdriver 12mm & 13mm socket, with ratchet Dremel or similar with cut off disc Large Phillips screwdriver
More informationSpark Plug replacement on VW 2.0L engine with AEG code
Spark Plug replacement on VW 2.0L engine with AEG code This is document is an attempt to describe and illustrate to some extent the process of replacing the spark plugs on a Volkswagen 2.0L engine with
More informationv Porsche 928
1985-86 32v Porsche 928 Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger kit at this price relies
More informationMustang Radiator Conversion DIY. By GearHeadPeter. January 27, 2011
1964-1966 Mustang Radiator Conversion DIY By GearHeadPeter January 27, 2011 We all know that the radiators in our cars are not the best, especially if you have done any customization to the engine, which
More information2001 BMW X5 4.4i. Fuel Filter Replacement
P P 2001 BMW X5 4.4i Fuel Filter Replacement Symptoms for Replacement: OBDII code P0171, Lean Bank1, which could be a bad or dirty MAF sensor Sluggish engine performance including hesitation with Wide
More information2012 SLK V6 (M276 Engine) Spark Plug Replacement
2012 SLK 350 3.5 V6 (M276 Engine) Spark Plug Replacement Proceed at your own risk. I read the Mercedes repair documents pertaining to changing the R172 SLK M276 V6 engine s spark plugs that I could find
More information7B1210 COBB BMW N54 Charge Pipe
7B1210 COBB BMW N54 Charge Pipe Installation Instructions Congratulations on your purchase of the COBB BMW N54 Charge Pipe for your BMW. The following instructions will assist you through your installation
More informationShotgun Double Barrel HPFP install guide
Shotgun Double Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Double Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationR-1125 C HARNESS MOUNT BAR INSTALLATION INSTRUCTIONS Fits C7 Corvette Coupes, including Z06
R-1125 C HARNESS MOUNT BAR INSTALLATION INSTRUCTIONS Fits C7 Corvette Coupes, including Z06 The R-1125 Harness Mount Bar has been designed and tested to provide a mounting point for the shoulder harness
More informationPeugeot 406 Coupe: Delocking your boot V.1 April 2005
This is a first stab at a DIY guide to de-locking your 406 Coupe. It isn t a hard modification to do yourself, but you do need to be confident working on your cars electrics and removing and refitting
More informationDoor panel removal F07 5 GT
Things needed Decent plastic trim removal tools Torx 30 Spare door clips 07147145753 I got away with a set of 5 but if I did it again I d be cautious and get 10. From prior experience if they are damaged
More informationShotgun Single Barrel HPFP install guide
Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationiphone 5s Front Panel Replacement
iphone 5s Front Panel Replacement Replace the cracked or broken screen on your iphone 5s. Note: DIY at your own risk. New beginner must be careful, screens got problems mostly due to wrong installation
More informationK6JRF's Page formerly W6FZC
K6JRF's Page formerly W6FZC My Mercedes Benz S500 Coupe (Updated: Nov 9, 2004) Analyze and Troubleshoot "Check Engine" MIL and Electronic Control Units (ECU)! Seat Belt Extender About one month ago, the
More informationInstallation Procedure Nissan Maxima SE 3L DOHC VE30DE
Phenolic Performance Intake Spacers Installation Procedure 1992-1994 Nissan Maxima SE 3L DOHC VE30DE Disclaimer: These spacers should only be installed by a qualified mechanic. If you decide to do the
More informationEURO HEADLIGHT ADJUSTER REMOVAL AND INSTALLATION
EURO HEADLIGHT ADJUSTER REMOVAL AND INSTALLATION This document is a step by step explanation of how to remove and replace the headlight adjusters in the Euro headlights. Parts needed to repair both headlights:
More information4 pieces of silicone hose Unless you have AEM then you have 2 2.5, 1 3, and 1 3.5
The parts in your kit: 3 pieces of Mandrel-Bent Aluminized Tubing: 1 Straight 1 45 degree bend with straight section 1 curved section 4 pieces of silicone hose 1 2.5 1 3.5 2 3 Unless you have AEM then
More informationPorsche 928 with 16v LH-Jetronic Fuel System
Porsche 928 with 16v LH-Jetronic Fuel System Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger
More informationCrawford Performance Top Mount Air/Oil Separator For 08 STi + Version 2 (S0713-1)
Crawford Performance Top Mount Air/Oil Separator For 08 STi + Version 2 (S0713-1) Parts List Part Number Quantity Description Sent Received S0709-1 1 TMIC Air/Oil Separator 08STI V2 F0365 1 Crank Case
More informationPage 1 of 14 This install requires work on your supplemental restraint system and could cause injury or damage to your car. If you are not comfortable performing the steps detailed here then do not attempt
More informationWritten By: Sam Lionheart
iphone 5s Front Panel Replacement Replace the cracked or broken screen on your iphone 5s. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 33 INTRODUCTION For an easier repair, use
More informationM60/M62 Camshaft Sensor Replacement
Page 1 of 10 Welcome, goldeneye006 Notifications My Profile Settings Log Out Forum What's New? Home Classifieds Vendors Vendor Specials Store New Rules Posts Private Advertising Messages FAQ Calendar Community
More informationBEDLAM SAUTOBOX MODIFICATION
BEDLAM SAUTOBOX MODIFICATION January 2006 Tocreate faster gearchanges. With thanks to Jared in the USA This mod can be done in around 2hours, by anyone who isn't scared to get their finger nails dirty.
More informationE ci M54 auto coupe' UK right hand drive
E46 2001 320ci M54 auto coupe' UK right hand drive 1/With the vehicle on hard level ground and chocks under the front wheels to prevent movement, raise the rear of the car up and use suitable stands to
More informationUrS6 Brake Servo Replacement Douglas Fifield July 2006
UrS6 Brake Servo Replacement Douglas Fifield (douglas.fifield@gmail.com) July 2006 This write-up covers the replacement of the brake servo on a 95.5 S6. The master cylinder remained intact and connected,
More informationThe Sands Mechanical Museum
The Sands Mechanical Museum How to Change Your Oil It is more difficult to change the oil in a Lotus Elise because the oil plug and filter are difficult to access. They are located behind an access panel.
More informationALTERNATOR REPAIR FOR BMW 645 CI. E64 ENGINE N62 BY KEVIN BOWEN 6/9/2013
ALTERNATOR REPAIR FOR BMW 645 CI. E64 ENGINE N62 BY KEVIN BOWEN 6/9/2013 Level of difficulty: If you follow these directions, moderate, hardest part is aligning the alternator back for repositioning. Length
More informationWritten By: Markus. Step-by-Step guide how to replace a dead NICD-Battery with LiFePO-Batteries. Rollei 6000/6008 Battery LiFePO4 Replacement
Rollei 6000/6008 Battery LiFePO4 Replacement Step-by-Step guide how to replace a dead NICD-Battery with LiFePO-Batteries. Written By: Markus ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION
More informationTools & Parts I Used. Here's everything that comes with the kit.
Ford Super Duty Power Tailgate Lock Install 2004 F250 4x4 XLT Sport Crew Cab Back to 2004 F250 Main Page This page describes the steps to install the Pop & Lock PL8250 power tailgate lock kit. This kit
More informationA Simple Guide to Installing the C2Motorsports 2.5L SRI
A Simple Guide to Installing the C2Motorsports 2.5L SRI Special Thanks to Josh and the Crew at Nothing-Leaves-Stock **Disclaimer: This is an aid for installing the SRI on a 2.5L motor. C2Motorsports is
More informationInstalling Nameless Performance High Flow cats on a Jaguar XKR
Installing Nameless Performance High Flow cats on a 2000-2002 Jaguar XKR Part I, removal preparation under the hood, left side. 1. Open the hood and remove the coolant tank cap on the driver's side of
More informationMustang CDC Lightbar (94-04) - Installation Instructions
Mustang CDC Lightbar (94-04) - Installation Instructions The below installation instructions work for the following products: Classic Design Concepts Mustang Convertible Lightbar (94-04 Carbon Fiber) Classic
More informationMustang Clutch Cable Installation Guide 96-04
Mustang Clutch Cable Installation Guide 96-04 The below installation instructions work for the following products: Steeda Adjustable Clutch Cable 96-04 Maximum Motorsports Clutch Cable 82-04 Steeda Clutch
More informationCorvette Set Separator (Glove Box) Lock Removal
1956-62 Corvette Set Separator (Glove Box) Lock Removal The materials here were gathered from several Corvette Forum Threads as well as from the Web Pages of Rich Mozzetta (rich5962 on the CF). Our colleagues
More information