Swifts cable ladder ancillary items
|
|
- Marcia Hopkins
- 5 years ago
- Views:
Transcription
1 earth continuity connector If a supplementary bonding conductor for equipotential earthing is required, straight lengths and fittings in all Swifts ladder ranges have fixing holes provided to accommodate a flexible earth continuity connector. On straight lengths, fixing holes are pitched every 75 mm to avoid the need for drilling if the ladder is cut When used with galvanised or finish ladder, the lug of the earth continuity connector is fixed directly to the ladder side rail Finish : electro tinned copper The earth continuity connector has a current capacity rating of mps Supplied in bagged quantities of ten with fasteners Dimensions (hole centres) 295 (braid length) Hole Ø6 5 Copper lug to BS 17 (1981) and BS 1977 (1976) 2 Conductor area 16 mm (copper braid to BS 4109) 12 0 Typical ladder length ends Two holes Ø7 5 Two holes Ø7 5 ttach the earth continuity connector to either hole, depending on coupler position Fasteners (included) Two fasteners per connector G, D, S and E finishes B C D E M6 x 10 Brass setscrew (BS 692) B Ladder side rail C Earth continuity connector D Brass 1 6 x 12 5 x 6 4 (BS420) E M6 Brass nut (BS 692) S () 79
2 hold down clips and insulated hold down clips Hold down clips are used for fixing cable ladder to trapeze hangers, Swiftrack channel or other flat support surfaces. They are fitted on the outside of the ladder rail Supplied singly without fasteners Supplied with the required nylon insulating pad, bush and washer Insulated versions for ladder are available on request, for details contact us on +44 (0) Cat. Nos. Standard hold down clip ZFF PFF EFF Insulated hold down clip ZF INF PF INF EF INF (continued) Standard hold down clip Hold down clip Insulated hold down clip Hold down clip Standard hold down clip Insulated hold down clip Ø15 nylon bush Nylon washer Nylon pad Insulated hold down clips are assembled as shown (typical) with the nylon pad, bush and washer providing the required insulation Standard hold down clips are assembled in the same way, but without the insulating parts (bold type see below) Use M10 screw, nut and washers to suit the application (not included) Use fasteners illustrated only those shown in bold type are included M10 x 40 long grade 4-70 setscrew Stainless steel hold down clip X One hole Ø11 40 Cat. Nos. (kg) ZFF PFF EFF Nylon 66 insulating pad bush 7 5 long washer spring washer nut Fixing hold down clips to supports ll types of support from the Swifts range are provided with correctly positioned fixing holes to accept hold down clips without drilling. The table contains data on fixing hole spacing required when attaching hold down clips to other supports Cat. Nos. Centre distance between fixing holes x ZFF W + 95 PFF W + 95 EFF W + 95 W = ladder width W S () Trapeze hangers : see p. 75 Swiftrack channel support : see p
3 hold down brackets and insulated hold down brackets Hold down brackets are used for fixing cable ladder to cantilever arms, trapeze hangers, Swiftrack channel or other flat support surfaces. They can be fitted on the inside or the outside of the ladder rail When used with other items from the Swifts range refer to the relevant product page for specific orientation details Supplied singly without fasteners Insulated versions for ladder are available, contact us on +44 (0) Insulated hold down brackets are supplied with the required nylon insulating pad, bush and washer Standard hold down bracket Insulated hold down bracket Standard hold down bracket Hold down bracket Insulated hold down bracket Hold down bracket Ø15 nylon bush Nylon washer Nylon pad B 40 Standard hold down bracket ZJF PJF EJF Insulated hold down bracket ZJ INF PJ INF EJ INF Insulated hold down brackets are assembled as shown (typical) with the nylon pad, bush and washer providing the required insulation. Standard hold down brackets are assembled in the same way, but without the insulating parts (bold type see below) Use M10 screw, nut and washers to suit the application (not included) Use fasteners illustrated only those shown in bold type are included Stainless steel hold down bracket M10 x 40 long grade 4-70 setscrew X 9 One hole Ø11 Cat. Nos. B (kg) ZJF PJF EJF Nylon 66 insulating pad bush 7 5 long washer spring washer -70 nut Fixing hold down brackets to supports ll types of support from the Swifts range are provided with correctly positioned fixing holes to accept hold down brackets without drilling. The table contains data on fixing hole spacing required when attaching hold down brackets to other supports Cat. Nos. Centre distance between fixing holes inside ladder Y outside ladder x ZJF W 44 W + 80 PJF W 44 W + 80 EJF W 44 W + 80 W = ladder width Y W S () Cantilever arms : see p. 74 Swiftrack channel support : see p
4 boltable hold down brackets Boltable hold down brackets enable all ranges of cable ladder to be secured to either Swiftrack or fabricated structural steel supports Brackets can be fitted wherever supports are available along the length of the ladder and fit to the inside of the ladder side rails thus minimising the total width required Supplied singly with bracket to ladder fasteners Support between rungs Support under rungs 55 Four 7 x 1 slots Cat. Nos. (kg) ZNF PNF ENF When attaching boltable hold down brackets to fabricated structural steel supports, the spacing between fixing holes should be W - 64 mm, where W is the ladder width Bracket to ladder fasteners (included) Cat. Nos. ZNF PNF ENF Quantity of fasteners per bracket M10 x 20 coachbolt M10 flange nut Fastener finishes For ladders with G, D and E finishes, fasteners are high tensile Grade 8.8 hot dip galvanised For ladders with S finish, fasteners are corrosion resistant stainless Grade 470 n alternative material for fasteners may be required depending on the installation environment, for details contact us on +44 (0) Bracket to support fasteners (not included) Slots are provided for M10 setscrews length to suit application S () 82
5 boltable angled hold down brackets Boltable angled hold down brackets enable the Swifts ranges of cable ladder to be secured to Swifts heavy duty cantilever arms and trapeze hangers. Brackets can be fitted wherever supports are available along the length of the ladder and fit to the inside of the ladder side rails thus minimising the total width required Boltable angled hold down brackets are supplied in handed pairs with bracket to ladder fasteners For fixing cable ladder to Swiftrack channel or structural steel supports use boltable hold down bracket, see p. 82 Cantilever arm between rungs Trapeze hanger between rungs 0 Two 22 x 11 slots One 7 x 1 slot Trapeze hanger under rung (1) Trapeze hanger under rung (2) Cat. Nos. (kg) ZPF PPF EPF ll weights given are in kilograms (kg) and are for a pair of brackets in hot dip Bracket to ladder fasteners (included) Cat. Nos. ZPF PPF EPF Quantity of fasteners per bracket M10 x 20 coachbolt M10 flange nut Fastener finishes For ladders with G, D and E finishes, fasteners are high tensile Grade 8.8 hot dip galvanised For ladders with S finish, fasteners are corrosion resistant stainless Grade 470 n alternative material for fasteners may be required depending on the installation environment, for details contact us on +44 (0) Bracket to support fasteners (not included) Slots are provided for M10 setscrews length to suit application S () Cantilever arms : see p. 74 Trapeze hangers : see p. 75 8
Swifts cable ladder ancillary items
short reducer brackets Short reducer brackets can be used with all cable ladder ranges to provide a simple and economical way of forming a reducer on site single bracket can be used with a straight coupler
More informationCable management ceiling systems
t PODUTS AND SSTEMS FO ELETIAL INSTALLATIONS AND INFOMATION NETOS Swifts cable ladder P. 212 Selection chart P. 220 Supports P. 216 Light duty (Opal) ladder P. 221 Ancillary items P. 217 General purpose
More informationSeries 2, 3, 4, & 5 Aluminum - Accessories
Wedge Lock Splice Plates Standard 4-hole pattern. Furnished in pairs, with hardware. One pair including hardware provided with each section. Boxed in pairs with hardware. For field installation drill 13
More informationSeries 2, 3, 4, & 5 Aluminum - Accessories
The following is a list of accessories and fittings that can be provided with S8 tray. For more information on these items, contact our Engineering Department. Fittings Horizontal Bends 30 Bends with 24,
More informationSeries 2, 3, 4, & 5 Steel - Accessories
- ccessories Splice Plates Standard 8-hole pattern for all steel splice plates. One pair including hardware provided with straight section. Boxed in pairs Expansion Splice Plates Expansion plates allow
More informationSwifts SW strength, speed and flexibility
Swifts SW strength, speed and flexibility STEEL WIRE CABLE TRAY / PRODUCT GUIDE Global vision... 21st Century solutions Established in the UK since 1972, Legrand is a world leading manufacturer of products
More informationCABLE MANAGEMENT SOLUTIONS CATALOGUE2003/04 A COMPLETE CABLE MANAGEMENT SOLUTION FOR COMMERCIAL AND INDUSTRIAL APPLICATIONS.
CLE MNGEMENT SOLUTIONS CTLOGUE2003/04 COMPLETE CLE MNGEMENT SOLUTION FOR COMMERCIL ND INDUSTRIL PPLICTIONS www.legrand.co.uk FSTRCK F31 FSTRCK F31 SYSTEM STEEL WIRE CLE TRY Legrand With a large range of
More informationSwifts SW. strength, speed and flexibility STEEL WIRE CABLE TRAY / PRODUCT GUIDE
Swifts S strength, speed and flexibility STEEL IRE CABLE TRAY / PRODUCT GUIDE Global vision... 2st Century solutions Established in the UK since 972, Legrand is a world leading manufacturer of products
More informationSeries 1 Steel - Accessories
- ccessories Standard (L-Shaped) Splice Plates One pair including hardware provided with each section. Prepackaged in pairs in a plastic bag, with hardware. 4-hole pattern L-shaped splice plates. L-shaped
More informationSeries 3 & 4 Stainless Steel - Accessories
- Accessories Splice Plates Standard 8-hole pattern for all steel splice plates. One pair including hardware provided with straight section. (Expansion splice quantity subtracted) Boxed in pairs with hardware.
More informationSeries 1 Steel - Straight Sections
Series 1 Steel - Straight Sections Series 1 Steel H-1 B-Line series Cable Tray Systems Series 1 Steel - ccessories & Fittings Series 1 Steel How The Service dvisor Works We know that your time is important!
More informationSwifts XRF extra heavy duty return flange straight lengths
Swifts F extra heavy duty return flange straight lengths and weights Loading graphs Load tests carried out to BS EN 61537 The loads shown on all graphs are the safe recommended maximum loads that can be
More informationSeries 2, 3, 4, & 5 Aluminum - Straight Sections
- Straight Sections I-1 B-Line series Cable Tray Systems - Accessories For Aluminum Fittings see fittings section pages L-1 thru L-17 How The Service Advisor Works We know that your time is important!
More informationSeries 2, 3, 4 Steel Cable Ladder Steel Cable Ladder, Series 2, 3, 4 & 5
Cable Ladder with Slotted Rung (shown with alternating slot orientation) Cable Ladder with Slotted Rung (shown with continuous slot down - also available with continuous slot up) HDS-1 Steel Cable Ladder,
More informationCABLE MANAGEMENT SOLUTIONS CATALOGUE2003/04 A COMPLETE CABLE MANAGEMENT SOLUTION FOR COMMERCIAL AND INDUSTRIAL APPLICATIONS.
CABLE MANAGEMENT SOLUTIONS CATALOGUE03/04 A COMPLETE CABLE MANAGEMENT SOLUTION FOR COMMERCIAL AND INDUSTRIAL APPLICATIONS www.legrand.co.uk CHANNEL SUPPORT THE BACKBONE OF ALL YOUR SUPPORT NEEDS Swifts
More informationBILMAT ENGINEERING (An ISO 9001:2008 certified company)
BILMAT ENGINEERING (An ISO 9001:2008 certified company) ADDRESS 352,353 G.I.D.C, INDUSTRIAL ESTATE, POR, RAMANGAMDI, VADODARA -391 243, GUJARAT. PROPRIETOR DIPAK L PATEL PHONE NO 0265 6540425 E-MAIL dipak@bilmatengg.com
More informationREDI-RAIL - Accessories
- ccessories Standard Splice Plate One pair including hardware provided with each straight section. (Expansion splice quantity subtracted) R4-SSP R5-SSP R6-SSP R7-SSP Expansion Splice Plate Bonding jumpers
More information[ ] ] [ 6a2O s6 Height B PW CABLE TRAY PW CABLE TRAY
PW CBE RY PW CBE RY Covers protect and contain cables. hey are highly recommended ray Covers to avoid damage to the tray contents and to protect against the elements. Some covers can also be attached to
More informationCable ladder systems. Development and testing
Cable ladder systems Metsec cable ladder systems have been developed to provide cost effective solutions for the support of cables in a wide range of market sectors. These sectors include: * Coercial *
More informationElectrak powertrack / underfloor busbar system
design and installation n General installation notes Electrak powertrack is a compact system that can be installed in floor voids as low as 48 mm Feed units are provided with one or two 25 mm diameter
More informationSwifts cable ladder building on innovation
Swifts cable ladder building on innovation PRODUCT TECHNICL GUIDE / INCLUDING SWIFTRCK ND SUPPORTING SYSTEMS CONTENTS INTRODUCTION Swifts cable ladder features 2 Legrand worldwide 4 Sustainable development
More informationPRODUCT CATALOGUE - CABLE TRAYS
PRODUCT CATALOGUE - CABLE TRAYS 098711969 shivshaktiindustries.delhi@gmail.com S. S. Engineering, B-2621, DSIDC Complex, Narela Industrial Area, New Narela, Delhi-140 Table of Contents Perforated Cable
More informationREDI-RAIL - Accessories
Standard Splice Plates One pair including hardware provided with each straight section. Offset Reducing Splice Plates FLEX-MOUNT djustable Splice Plates 1 /4" hardware. Horizontally adjustable to 90. Vertically
More informationCatalog & Cable Ladder System. Guide. cable management system
Catalog & Cable Ladder System Guide L4 Cable Ladder - mm Sidewall L5 Cable Ladder - mm Sidewall L6 Cable Ladder - mm Sidewall L4L/ L4L/ L4L/ L4L/ L4L/ L4L/ L5L/ L5L/ L5L/ L5L/ L5L/ L5L/ L6L/ L6L/ L6L/
More information5_Cable_Ladder_Layout 1 26/01/ :46 Page 35 CABLE LADDER
5_Cable_Ladder_Layout 1 26/01/2012 09:46 Page 35 CABLE LADDER L4 Cable Ladder - mm Sidewall L4L/ L4L/ L4L/ L4L/ L4L/ L4L/0 0 L5 Cable Ladder - mm Sidewall L5L/ L5L/ L5L/ L5L/ L5L/ L5L/0 0 L6 Cable Ladder
More informationBus bar Bushings up to 1.1kV and from 1.6kA to 4kA for Liquid Filled Transformers:
4 (Four) Pole Monoblock: Bus bar Bushings up to 1.1kV and from 1.6kA to 4kA for Liquid Filled Transformers: Designed and manufactured in accordance with EN 50336:2002 and BS 2562: 1979 1 Introduction:
More informationSECTION PIPE HANGERS AND SUPPORTS
Part I - GENERAL 1.01 SECTION INCLUDES A. The work covered under this section consists of the furnishing of all necessary labor, supervision, materials, equipment, and services to completely execute the
More information35-kV Thru-Bushings F Series (bolt-in) for Air-Insulated to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp
Page 1 2018 Equipment Connection Bus Bar, or Grounded Metal Equipment Plate F Series Mounting Holes ELRIM Cycloaliphatic Epoxy Provides: Nontracking, self-scouring, nonweathering performance Superior dielectric
More informationArena-Walsall power track system standard
standard Standard track length SL12 Standard feeder unit SFU Standard tap-off SO3U Standard SFB 1 Dimensions and technical information (p. 198-199) wo bar and earth 63 power track system Pack Cat. Nos.
More informationSeries 3 & 4 Stainless Steel - Accessories
Splice Plates Standard 8-hole pattern for all stainless steel splice plates. One pair including hardware provided with straight section. Boxed in pairs with hardware. Expansion Splice Plates Expansion
More informationSeries 1 Steel - Straight Sections
- Straight Sections H-1 -Line series able Systems - ccessories & Fittings How The Service dvisor Works We know that your time is important! That s why the color-coding system in this catalog is designed
More informationCENTRE FEED UNIT UP TO 4000A. Safety
CENTRE FEED UNIT UP TO 000A Safety Centre feed unit New TCC section busbar: Connection options with CRITO PowerClip and CRITO ProfiClip, and terminal studs (screw in c-slot). 1-pole, side busbar support
More informationCable Tray and Accessories
Vergokan Cable Tray Cable Tray and Accessories 1 salesinfo@mechanicalsupport.co.nz PO Box 204336 Highbrook Auckland www.mechanicalsupport.co.nz Vergokan Cable Tray 2 Vergokan Cable Tray KBSI 35 Series
More information15 kv and 25 kv Thru-Bushings
Page 1 2001 ELRIM Cycloaliphatic Epoxy Provides: Nontracking, self-scouring, nonweathering performance Superior dielectric strength, dielectric loss and power factor Choice of shapes allows design innovation
More informationadaptable, reliable underfloor power
adaptable, POWERTRACK reliable adaptable, reliable underfloor power 6 THE INDUSTRY STANDARD IN UNDERFLOOR POWER Electrak powertrack / underfloor busbar is perfect for cavity floor installations. With minimal
More informationTubing & Hose Metric. Nylon, Polyurethane, Polyester Reinforced PVC, Metal Braided Rubber, Copper, Double Wall Brazed Steel
Tubing & Hose Metric Nylon, Polyurethane, Polyester Reinforced PVC, Metal Braided Rubber, Copper, Double Wall Brazed Steel Available in a variety of different types to suit a wide range of applications
More informationWESTERN ELECTRICITY SUPPLY COMPANY OF ORISSA, WESCO. GUARANTEED TECHNICAL PARTICULARS 1 of 2
Sl. No. WESTERN ELECTRICITY SUPPLY COMPANY OF ORISSA, WESCO GUARANTEED TECHNICAL PARTICULARS 1 of 2 REQUIREMENTS 11 Kv, 200 Amps, A.B Switches. Particulars 1 Maker's name and Country of origin. 2 Type
More information25 kv Apparatus Bushings
Page 1 2001 ELRIM Cycloaliphatic Epoxy Provides: Nontracking, self-scouring, nonweathering performance Superior dielectric strength, dielectric loss and power factor Choice of shapes allows design innovation
More informationPipe Brackets - Pipe Support. Systems Brass Pipe brackets Brass Pipe clips
Select Language Home Profile Products Contact Us Email Resources Brass Sanitary Fittings Brass Cable Glands Cable Gland Accessories Brass Fasteners Pipe Brackets - Pipe Support Systems Brass Pipe brackets
More informationSteel Conduits Conduit Fittings Flexible Conduits
Conduits Conduit Fittings Flexible Conduits CONTENT 1. INTRODUCTION VOLTECX products introduction and selecting VOLTECX 2. STEEL CONDUITS VOLTECX BS4568: Part 1: 1970 (Class 4) Conduit IEC 61386-21:2004;
More informationSteel Framing Systems
Steel Framing Systems Total Cable Management Solutions BS-EN-ISO 9001:2000 QULITY MNGEMENT SYSTEM Kazakhstan - 090301 Republic of Kazakhstan, West Kazakhstan Oblast, ksai, Pramzone, BKKS office complex
More information25-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp
Page 1 2018 Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other Component 15 kv or 25 kv Separable Insulated Connector (elbow) Equipment Connection Power Cable Power Cable ELRIM Cycloaliphatic
More informationInstalling a Downstream Distribution Panelboard
Job Sheet 5 Installing a Downstream Distribution Panelboard OBJECTIVE To install a downstream distribution panelboard (DDP) on the Mobile Workstation. To mechanically and electrically connect the DDP to
More information35-kV 200-kV BIL Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp
Page 1 2018 Grounded Metal Equipment Plate Equipment Connection 35 kv Separable Insulated Connector (elbow) Bus Bar or Other Component Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other
More information35-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp
Page 1 2018 Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other Component 35 kv Separable Insulated Connector (elbow) Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other
More informationGROUNDING & BONDING PRODUCTS
GROUNDING & BONDING PRODUCTS Busbars Page 5-3 Insulators Page 5-8 Grounding Products Page 5-9 Compression Tools, Lugs & Taps Page 5-14 Learn About CPI s Extended Limited Warranties for coverage of (2)
More informationCable ladder systems. 319 Fittings, side rail height 110 mm 320 Accessories for side rail height 45, 60, 110 mm. Hold-down clamps
Side rail height 45 Light-duty rung, cable ladder length 3.0 m, Rail thickness.25 Light-duty rung, cable ladder length 6.0 m, Rail thickness.25 Light-duty rung, cable ladder length 3.0 m, 306 308 Rail
More information2: Ecokit Ecokit 11 Overview A 2_ Ecokit 11 Sub Rack Configuration A 2_ Width A 2_ Height / Depth A 2_6
2: Ecokit 11 2.1 Ecokit 11 Overview 2_3 2.2 Ecokit 11 Sub Rack Configuration 2_5 2.2.1 Width 2_5 2.2.2 Height / Depth 2_6 2.2.3 Handles 2_6 2.2.4 Line Drawing 2_7 2.3 daptation Kits 2_8 2.3.1 daptation
More informationUSA Canada On the Internet: Toll Free wieland Product Range Electrical Connections
0.2 F 01/02 270 Excerpt from our master catalogue wiecon PCB terminals In Ageneral, all Wieland components which are obliged to have the identification are provided with the A mark Pluggable PCB terminals
More informationSeries 1 Steel - Straight Sections
LST-1 able Systems - Straight Sections How The Service dvisor Works -Line knows that your time is important! That s why the color-coding system in this catalog is designed to help you select products that
More informationPORTA-DOCK, INC. 100A 1284 ALUMINUM CANTILEVER BOAT LIFT
Page 1 of 7 PORTA-DOCK, INC. 100A 1284 ALUMINUM CANTILEVER BOAT LIFT Thank you for purchasing our product! Please read these instructions and follow them step by step. * STEP 1. Separate and group like
More informationSTRAIGHT PERFORATED TRAY
STRAIGHT PERFORATED TRAY RETURNED EDGE TYPE RETURNED FLANGE TYPE NOTE: Other sizes are available upon request WIDTH (W) HEIGHT (H) 50 15 15 150 15 15 15 400 15 500 15 600 15 STRAIGHT CABLE TRAY STANDARD
More informationAll fitting are offered at 300mm Radius as standard and others Radius available on request.
Heavy Duty Profile Standard s:,,,,,,,, 0-. Other widths are also available on request. EMI Ladder is designed to give a maximum Cable Loading Capacity whilst retaining high strength. By utilizing high
More informationCRITO Connection technology. Double and triple T and TCC section busbars
Centre feed unit 5 Centre feed unit Centre feed unit 5 Centre feed unit up to 4000 A combines the advantages of high short-circuit capacity, drill-free mounting, brace terminal technology and clearly structured
More informationSTANDARD SHAPES TROLLEY PARTS MANUAL
STANDARD SHAPES TROLLEY PARTS MANUAL, Unified Industries, Inc. All Rights Reserved. www.unified-ind.com PARTS AND REPAIR MANUAL This manual has been compiled to expedite the ordering of repair parts for
More informationBulletin 1494F Fixed-Depth Flange-Mounted Disconnect Switches. Selection Guide
F Fixed-Depth Flange-Mounted Disconnect Switches Selection Guide F Fixed-Depth Flange-Mounted Disconnect Switches Product Cat. No. 1494F-N Disconnect Switch with Cat. No. 1494F-F Fuse Block Adapter Plate
More informationCable Support Systems Admiralty Pattern Tray Cable Ladder Type 2/30 Cable Ladder Type 3/50 K-1000 Channel KT3/KT5 Ladder Tray
www.hesales.com.au Cable Support Systems Admiralty Pattern Tray Cable Ladder Type 2/3 Cable Ladder Type 3/5 K- Channel KT3/KT5 Ladder Tray -.55mm base Galvabond - 2.4m length. 14mm side - Self-splicing
More informationEARTH RODS GROUP. Cross earth rod. 3 mm homogeneous thickness Item Section bar in mm Length in m. Weight/each Pcs per box
Cross earth rod. 5 mm homogeneous thickness Item Section bar in mm Length in m. Weight/each Pcs per box structural steel, 50x50x5, with three holes flag Ø mm. Standards DC 5-00 50x50x5,00 Kg 3,750 50 DC
More informationCable Ladder System for Ships
Cable Ladder System for Ships Our product range specially designed for installation in ships is available in two distinctive types: RZE-R is a cable ladder with a smart design which reduces the need for
More informationCOUPLERS. SW4 / CS / GA System Type Coupler Type Finish
The Speedway Coupling System has been designed to prevent slip between connected components a common problem for slotted cable ladder systems when under load. The slot pattern in the ladder sides can be
More informationCable Cleats. Trefoil Cable Cleat with LSF Pad. 55mm CC-2
CC-1 Trefoil Cable Cleat with LSF Pad 1. Recommended for installations where the highest levels of short circuit withstand are required. 2. Short circuit current tested in accordance with BS EN 50368:2003
More informationPORTA-DOCK, INC. 100A 1200 LB. 84 WIDE ALUMINUM CANTILEVER BOAT LIFT 102A 1200 LB. 113 WIDE ALUMINUM CANTILEVER BOAT LIFT
Page 1 of 7 PORTA-DOCK, INC. 100A 1200 LB. 84 WIDE ALUMINUM CANTILEVER BOAT LIFT 102A 1200 LB. 113 WIDE ALUMINUM CANTILEVER BOAT LIFT Thank you for purchasing our product! Please read these instructions
More informationINSTALLATION MANUAL Model
VAN SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL Model 2291-3-01 ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT. CAUTION Be
More informationWIRE BASKET TRAY CANADIAN ELECTRICAL RACEWAYS INC.
CANADIAN ELECTRICAL RACEWAYS INC. WIRE BASKET TRAY Made of heavy-gauge zinc plated wire mesh, CER basket tray is ideal for your commercial or industrial cable management project. A full range of cable
More informationBulletin 1494V Variable-Depth Flange-Mounted Circuit Breaker Operating Mechanism
Bulletin V Variable-Depth Flange-Mounted Circuit Breakers Product Overview/Product Selection Circuit Breaker Kits Cat. No. V-C Circuit Breaker Kit (Shown without handle and connecting rod) Bulletin V Variable-Depth
More information1ZSE en, Rev. 3. Wall bushings, type GSA-AA Technical guide
1ZSE 2750-112 en, Rev. 3 Wall bushings, type GSA-AA Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.
More informationMarine cable ladders. Marine cable ladders
386 This chapter contains an overview of the RICO marine for various loads and applications subdivided in product families. Content Table of content Page 40 mm side height 390 387 System overview cable
More information1ZSE EN, REV. 4. Wall bushings type GSA-AA Technical guide
1ZSE 2750-112 EN, REV. 4 Wall bushings type GSA-AA Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.
More informationNOVO LIGHTED MIRROR. Installation Instructions
NOVO LIGHTED MIRROR Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Must be installed by a qualified technician. Read these installation instructions. Keep these instructions for future use. Follow
More informationTECHNICAL SPECIFICATION FOR SHACKLE HARDWARE FITTINGS SUITABLE FOR TENSION STRING TO BE USED FOR 11KV LINE
TECHNICAL SPECIFICATION FOR SHACKLE HARDWARE FITTINGS SUITABLE FOR TENSION STRING TO BE USED FOR 11KV LINE The hardware fittings suitable for tension string to be used for 11KV consisting of following
More informationMIRROR, GLASS AND PANEL TRIM
... MIRROR, GLASS AND PANEL TRIM RIGHT SHAPES RIGHT PRICE RIGHT NOW J CAP ALUMINUM CAP FOR 1/16" MATERIAL FR 0230, BC ALUMINUM CAP FOR 3/32" MATERIAL FR 0330, BC ALUMINUM CAP FOR 5/32" MATERIAL FR 0430,
More informationABN Quality Endorsed Company ISO9001 Lic No EDITION 2
ABN 43 8 71 335 SECTION 4 Cable Ladder and A U S T R A L I A W I D E A U S T R A L I A N M A D E Quality Endorsed Company ISO91 Lic No 13146 EDITION 2 SECTION 4: Cable Ladder & Type 3/5 Type 4/7L Type
More informationProduct Catalog. Fittings ½ AIR PIPE FITTINGS Fitting, 1/2 Air Pipe End Cap Coupler, with Tank Valve
To complement our extensive line of cable pressurization products, System Studies also sells a variety of air pipe and pressure tube fittings. This section of the catalog describes these commonly used
More informationBRACKETS, MOUNTS & HARDWARE
HIGH VOLTAGE SWITCHGEAR & AUTOMATION EQUIPMENT SECTION 6 Brackets, Mounts & Misc. Hardware CAT. NO: 040930G May, 2008 INERTIA Engineering & Machine Works, INC. Fax: (209) 931-8186 6665 Hardaway Road, Stockton,
More informationElectrak power track underfloor power distribution systems
4 www.electrak.co.uk Electrak power track underfloor power distribution systems Tel: 01207 503400 Fax: 01207 501799 Email: sales@electrak.co.uk Because of our policy of continuous improvement, Electrak
More informationTransmission Line Support Systems
Coax Bridge Kit Each Coax Bridge Kit provides rooftop support for coax transmission lines on three PVC sleepers and protects the coax from damage with an long steel cover. The three series of products
More informationINSTALLATION MANUAL Model
VAN SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL Model 2291-3-01 ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT. CAUTION Be
More information# INDEX. Created on: Revised on: N/A Cable Trays Manual 1 ABBREVIATIONS 2 SYSTEM COMPONENTS 3 DEFNITIONS 4 MATERIAL & FINISH OPTIONS
# INDEX 1 ABBREVIATIONS 2 SYSTEM COMPONENTS 3 DEFNITIONS 4 MATERIAL & FINISH OPTIONS 5 GENERAL INFORMATION 6 ADAPTATION TO NEMA STANDARDS 7 CABLE TRAYS 8 CABLE LADDERS 9 ACCESSORIES 10 SUPPORTS 11 INSTALLATION
More informationWelded cable ladder system
Welded cable ladder system System information Pure OBO cable ladder competence Electricians have placed their trust in OBO Bettermann cable ladders for decades. The range stretches from riveted connections,
More informationONTRAC WIRE MESH CABLE TRAY SYSTEM
P R O D U C T D ATA S H E E T ONTRAC WIRE MESH CABLE TRAY SYSTEM K E Y F E AT U R E S Available in two styles: Shaped and Standard Tray Easy to use pathway solution that supports large quantities of network
More informationElectrical and Mechanical Supports Systems
Electrical and Mechanical Supports Systems Index - Mechanical & Electrical Support Systems This catalogue contains Mechanical & Electrical Support Systems information only as indicated below. For any additional
More informationINDEX. Chapter1 6. air master. Volume Control Dampers
Chapter1 6 INDEX 1 Volume control damper...:avcd...16.1 Standard sizes...16.2 Fixing details...16.2 How to order...16.2 Performance chart...16.3 2. Circular volume control damper....:avcd-c....16.4 Standard
More informationSpade Terminals: Locking
Spade Terminals: Locking S SERIES FEATURES Tongue snaps around the screw & terminal is locked into place until the mounting screw can be tightened down. vinyl (PVC) 300V, 75 C. INSULATION TYPE WIRE RANGE
More informationA compact range of Switch-Disconnectors with the capacity to add auxiliary and neutral block options to the basic load break switch block.
PNE ISOTORS Craig & Derricott has a range of products designed specifically for control panel and switchboard construction. Most panels require a means of electrical isolation and the can offer variants
More informationELLIS PATENTS ELECTRICAL PRODUCTS
ELLIS PATENTS ELECTRICAL PRODUCTS UK PRICE LIST 2008 Issue 2 PAGE NO PRODUCT CATALOGUE PAGE NO 2 ALPHA ALUMINIUM TREFOIL CLEAT Product Update 2008 3 TCA ALUMINIUM CAST TREFOIL CLEAT 5 & 6 4 EMPEROR TREFOIL
More informationKnob handles Doorknobs Knobs & backplates
262 266 274 Knob handles Doorknobs Knobs & backplates Overview 08 0802 08 0803 Page 262 08 0804 Page 262 08 0826 Page 263 08 0828 Page 263 08 0829 Page 264 08 0844 Page 264 08 0880 Page 265 23 0802 Page
More informationElectronic Enclosures Technical Information 445/441 Panel Instrument Cases Acc. to DIN 43700/IEC 61554
Electronic Enclosures Technical Information 3. Switching and Control Panel (Switchboard) Instrument Cut Outs 2,5 t 3,2 Type l Permitted tolerance l2 Permitted tolerance X M 2 Specification for a switchboard
More informationLIGHTING JUNCTION BOX
Channels Max. No. of Terminals Cat No. Max. Max. 4 10 16 35 50 70 95 Size Length No. mm 2 mm 2 mm 2 mm 2 mm 2 mm 2 mm 2 DB 6006 260 x 160 L 245 1 30 20 16 B 145 2 32 22 18 6 DB 6024 300 x 225 L 285 2 72
More informationData Sheet No 241 Jan 2002 Issue G. Electrode Holders & Brackets for Conductivity Type Systems
HAWKER Data Sheet No 4 Jan Issue G LEVEL CONTROL SYSTEMS Holders & Brackets for Conductivity Type Systems Heavy Duty HPE8 Heavy Duty HPE8/P Heavy Duty E holder suitable for sewage, water and effluent applications.
More informationHSpecialties Inc. TABLE OF CONTENTS
TABLE OF CONTENTS Introduction... Curtain Track Selection Guide...2 Ordering COMPLETE Tracks...3 00 Series Standard-Duty Straight Track...4 200 Series Black Medium-Duty Straight Track...8 300 Series Standard-Duty
More informationCable Fixing. Cable Fixing. Cable Tray Systems
220 Trefoil Cable Cleat with LSF Pad 1. Cable Cleats are recommended for installations where the highest levels of short circuit withstand are required. 2. Cable Cleats have been short circuit current
More informationA14. external sliding system. 175kg max panel weight. 3m (h) x 4m (w) max panel size. side or top-fixed tracking. precision-ground bearings
A14 external sliding system 175kg max panel weight 3m (h) x 4m (w) max panel size side or top-fixed tracking precision-ground bearings A14 SLIDING HARDWARE SYSTEM A14: SLIDING SYSTEM Precision bearing
More informationPage: REV 3: Add drill and tap information to Figure 4 DRILL #3, TAP 1/4-28 BOTH ENDS.
REVISION DESCRIPTION: 1) Page: 32-03 MEMO: Step 4 should not be bold. Fix WD-1213 callout in Figure 3. Page: 32-04 REV 3: Add drill and tap information to Figure 4 DRILL #3, TAP 1/4-28 BOTH ENDS. Add make
More informationPIPING. Aluminium pipe for inert gases (5,7 m / 18,7 ft) PAGE 2/ AIRNET Ø (MM / INCH) PARTNUMBER LOT SIZE / ¾" 05
PIPING Aluminium pipe for inert gases (5,7 m / 18,7 ft) 2811 1061 05 20 / ¾" 05 2811 2061 05 25 / 1" 05 PAGE 2/99 2014-11-24 Aluminium pipe for air (2,85 m / 9,4 ft) PIPING 2811 1063 10 20 / ¾" 10 2811
More information3 DOOR SYSTEM ROOMFOLD DELUXE RANGE
ROOMFOLD DELUXE RANGE 3+0 Door Pattern 3 DOOR SYSTEM SYSTEM OVERVIEW Pivot Door Daily Access Door 282 HSS Drop bolt position on reverse of door 106 SSMF Guide TOOLS REQUIRED 24mm & 17mm Router Bit IMPORTANT
More informationCooper & Turner Ltd STRUCTURAL
Cooper & Turner Ltd STRUCTURAL Page 1 of 6 Dimensions of Fully Threaded Bolts/Setscrews CHARACTERISTIC STANDARD Thread d M12 M16 M20 M24 M30 M36 p (pitch) 1.75 2 2.5 3 3.5 4 a max. 5.3 6 7.5 9 10.5 12
More informationPRODUCT CATALOGUE MECHANICALSUPPORT.CO.NZ 0508 CABLE TRAY CERTIFIED QUALITY SYSTEM ISO 9001:2015 REGISTERED COMPANY
BS OHSAS 18001:2007 & AS/NZS 4801:2001 Certificate No. NZP1023HS R PRODUCT CATALOGUE REGISTERED COMPANY MECHANICALSUPPORT.CO.NZ 0508 CABLE TRAY Who we are Founded in 2005 by Directors Hayden Froggatt and
More informationA70 ARCADE ENDFOLD & CENTREFOLD FOLDING DOORS ALUMINIUM SECTIONS BOTTOM ROLLER TIMBER DOORS
CI/SfB (31.54) Xt7 A R C A D E ENDFOLD & CENTREFOLD A70 E A C H D O O R W E I G H T M A X 7 0 k g ISSUE 1 ARCADE FOLDING DOORS ALUMINIUM SECTIONS BOTTOM ROLLER TIMBER DOORS H E N D E R S O N APPLICATION
More informationCATALOGUE PIPE SUPPORTS
CTOGUE B R T IN SIN C E 1 9 2 4 G 90 YERS ST E RU CE T PIPE SUPPORTS O F PIPE SUPPORTS - PICTORI INEX PIPE SUPPORTS The Unistrut pipe support systems covers an extensive range of hangers, pipe clips, pipe
More informationNew. Axle Spindles. Universal Tie Plates. Tie Plates. Axle Tie Plate Kits. Includes: nut, washer and cotter pin.
Axle Spindles Spindle Bearing Description Surface Part # 1-1/4 x 7 1 80055 1-1/4 x 7 (a) 1-1/16 80060 1-3/4 x 8-1/4 1-1/16 x 1-3/8 80235 2 x 8-1/4 1-1/16 x 1-3/8 80325 Eliminator, 1,750# (b) 80324 Nut/Washer/Cotter
More information