STAINLESS STEEL CYLINDER CONSTRUCTION

Transcription

1 STAINLESS STEEL CYLINDER CONSTRUCTION In the early 950 s, Clippard introduced miniature pneumatic cylinders and valves to industry. No other manufacturer can boast of the same experience or knowledge of miniature components. Air cylinders have always been an integral part of the Clippard Minimatic line. Over the years Clippard has responded to requests from cylinder users to provide additional sizes of air cylinders and auxiliary support products. While competitively priced, these products maintain the Clippard standard for quality and reliability that has been the industry standard for many years. Sintered bronze bushing on clevis and universal mount cylinders Piston rod joint is threaded and bonded for extra strength Drilled relief holes for full piston area breakaway Anodized heads Long life U cup rod seals Extra rod length for greater thread engagement and adjustment 304 stainless steel body Long life U cup piston seals 303 stainless steel rod, ground, polished and roller burnished for a hard, mirror finish Sintered bronze rod bushing Wrench flats to aid in installation Features Polished I.D. 304 stainless steel tubes for low breakaway Precision rolled construction for a solid, leakproof cylinder at a reasonable price Machined aluminum heads are clear anodized for extra protection against corrosion Cylinder heads are machined from one side for better concentricity Sintered bronze rod bushing Sintered bronze clevis bushing on all clevis and universal mount cylinders Rods are threaded and bonded to pistons Repairable rod seal on 28 through 48 series Ground, polished and roller burnished 303 stainless rods provide a smoother rod finish that protects rod seals, giving longer life Full piston area breakaway to assure full power from the beginning of each stroke Buna-N U -cup piston seals for full power, low friction and trouble-free performance Buna-N U -cup rod seals for leakproof operation Temperature range: 32 to 230 F Maximum pressure: 250 psig 2 Clippard Instrument Laboratory, Inc

2 STAINLESS STEEL CYLINDER NUMBERING SYSTEM Stroke In inches & fractions of an inch Mounting Type S - Stud U - Universal C - Clevis F - Front Block E - End Stud T - Trunnion Rod Type D - Double Ended Rod R - Rotating Rod N - Non-Rotating Rod H - Hollow Rod Cylinder Type D - S - R - Reverse Acting F - Front Spring Bias B - Back Spring Bias Not all combinations are available - consult factory Bore 05-5/ /2 0-5/8 2-3/4 4-7/8 7 - / / /2 28-3/ / Options B - Bumpers V - Fluorocarbon Seals C - Cushions MB - Magnetic Piston for Hall Effect sensors (includes bumpers) F - Cushion Front End R - Cushion Rear End W - Rod Wiper S - Side Ported H - Heavy Spring P - Rotated Ports SPECIFICATIONS STAINLESS STEEL CYLINDER STANDARD & HEAVY SPRING FORCES Bore Size 5/6 /2 5/8 3/4 7/8 -/6 -/4 -/2-3/4 2 2-/2 3 Force Factor - Extend (Area) Rod Size /8 3/6 3/6 /4 /4 5/6 3/8 7/6 /2 5/8 5/8 3/4 Rod Area Force Factor - Retract (Area) lbs /6 bore /2 5/8 3/4 5/6 5/6 7/8 /6 /4 /2 3/4 Standard Spring Forces (lbs) 2 2 /2 The force required, operating air pressure and cylinder bore are all factors that must be determined or known when sizing an air cylinder. If two are known the other is easily calculated per the formulas and triangle shown below. Area is derived using either of the following formulas: Diameter 2 x or Radius 2 x π Bore 5/6 /2 5/8 3/4 7/8 -/6 -/4 -/2-3/4 2 2-/2 At Rest Compressed Heavy Spring Forces (lbs) Bore 5/6 /2 5/8 3/4 7/8 -/6 -/4 -/2-3/4 2 2-/2 At Rest N/A N/A N/A N/A Compressed N/A N/A N/A N/A F - Force or load in pounds P - Pressure A - Area of cylinder (square inches) P F A F = P x A P = F / A A = F / P Clippard Instrument Laboratory, Inc

3 STAINLESS STEEL CYLINDER OPTIONS The following options are available with Clippard stainless steel cylinders. Available options are shown by the abbreviations noted in the information shown with each standard cylinder. Fluorocarbon Seals -V This option is used in applications where chemical resistance, compatibility and temperature become an issue. Temperature ranges: -20 up to 400 F. Cushions -C (Front Cushion Only) -F (Rear Cushion Only) -R Clippard s cushion cylinders offer an adjustable cushion to slow the cylinder near the end of the stroke to reduce impact and prolong cylinder life. Our adjustment needle is held captive to prevent the needle from blowing out. The cushion can be adjusted to have a dead stop /2 from end of stroke or adjusted to have virtually no effect on the action of the cylinder. See specific cylinder specifications for availability of this option. No Rod Threads -N Rods are provided with no threads when this option is ordered. Magnetic Piston -MB A magnet is attached to the piston that will actuate the Hall Effect and reed switches. This option also includes bumpers and extends the overall length of the cylinder. Switches and clamps need to be ordered separately. For more information see page 83 on Clippard s Hall Effect and reed switches. For multiple reed switches we need a stroke or more. Maximum temperature 300 F. Rod Wipers -W Rod Wipers are added to cylinders in applications where a liquid wash could dry out the rod seals of a double acting cylinder. Non-standard Options Extra Rod Extensions Thread Modifications Silk Screening Private Labels If you can t find a cylinder to suit your needs call your Clippard distributor to inquire about custom cylinders. Bumpers -B Internal polyurethane bumpers are supplied for applications where the cylinder is cycled with a light load and/or high speeds. The elastic bumpers reduce noise and shock to the load. Use of this option may add to the overall length of the cylinder. See specific cylinder listings on the following pages for availability and details of the overall length added. Maximum temperature 200 F. Side Ported -S Side ported rear heads are sometimes needed when the standard cylinder has the rear port out the back. This option changes the design of the rear head so the rear port is located on the side of the cylinder. Overall length of cylinder changes with this option. Heavy Spring -H In single acting, reverse acting or spring bias cylinders the standard spring force can be changed by ordering the -H option. The spring forces for the heavy springs are shown on page 3. Rotated Ports B2 B3 B A2 B4 Option Rear Front # Port Port P2 B2 A2 P3 B A2 P4 B4 A2 P5 B3 A2 P6 B4 A P7 B3 A P8 B2 A This option is used in applications where ports need to be rotated to accommodate a specific space requirement or port orientation for the fittings and tube attachments. The diagram explains the options and orientation of the ports. See the specific cylinder to find availability of these options. A 4 Clippard Instrument Laboratory, Inc

4 STAINLESS STEEL CYLINDER STROKE LENGTHS Standard stroke lengths for each bore size and cylinder style are listed in this catalog. Non-standard stroke lengths (not listed in the catalog) up to 24 for single acting cylinders and 36 for double acting cylinders are available. Stroke length should be specified in inches and fractions of an inch. Consult the factory for other requirements. In applications, attention should be given to minimizing the side load on the rod to insure a smooth stroke without binding. Also, in applications where the cylinder rod is subjected to an unsupported column load, the load on the rod should be less than the force shown in the table below to prevent buckling of the rod. Rod Maximum Load (lbs) to Prevent Buckling of the Rod Rod Length / / / / / / / / / Rod Thread Bore Rod Rod Series Size Size Flats #5-40 UNC-2A 5/6 05 /8 none #0-32 UNF-2A /2 08 3/6 none #0-32 UNF-2A 5/8 0 3/6 none /4-28 UNF-2A 3/4 2 / /4-28 UNF-2A 7/8 4 / /6-24 UNF-2A /6 7 5/6 3/8-24 UNF-2A /4 20 3/8 7/6-20 UNF-2A /2 24 7/6 /2-20 UNF-2A 3/4 28 / /2-20 UNF-2A /8 /2-20 UNF-2A 2 /2 40 5/8 5/8-8 UNF-2A /4 If your application requires a custom feature that CUSTOM CYLINDERS you do not see in our catalog please contact our distributor in your area for assistance. We manufacture a wide variety of special cylinders. Examples of our custom cylinder capabilities would include: stroke and rod modifications, special mounting configurations and ports, seal and lubrication options, integrated valving and adjustable stroke cylinders. We also provide application based special cylinder design for those customers having unique parameters. FREE CYLINDER SAMPLE PROGRAM We invite competitive comparisons. If you are an OEM that uses air cylinders, Clippard will provide a free sample for your evaluation. Contact us or your local distributor and ask for the Free Sample CILinder request form. Clippard Instrument Laboratory, Inc

5 STAINLESS STEEL ACCESSORIES POSITION SENSORS Clippard pneumatic cylinders are available with a choice of magnetically operated position sensors. The magnetic reed switch or Hall Effect sensor... on cylinders equipped with magnetic piston option. Hall Effect Position Sensors Clippard Hall Effect sensors offer the user more accurate sensing of piston location for the ultimate in pneumatic system control. The Hall Effect sensor operates with Clippard stainless steel pneumatic cylinders equipped with internal magnets on the pistons. By accurately sensing the magnetic field of the piston when it passes beneath the sensor, the position of the rod piston is determined, and a feedback signal is created. See page 59. Reed Switches The Clippard RS magnetic reed switches have power ranges to 25 watts, current up to.5 amperes and a rated life span of 0 million cycles. Plan to use them where the high performance of the Clippard HS Hall Effect switch is not required. Two models are available: 36 volts or 200 volts AC/DC. Each is a SPST normally open configuration. When the cylinder s magnet-equipped piston moves to a location where the magnet is positioned below the reed switch, the switch sends a feedback signal to indicate piston location. In the 36 VDC model, an LED provides switch closing indication. See page 59. ACCESSORIES Mounting Hardware For efficient power and easy mounting, Clippard has designed and manufactured brackets suitable for each cylinder shown in this catalog. These products are shown on the last page of each corresponding bore size and include clevis mounting brackets, foot mounting brackets, rod clevis assemblies and rod eye assemblies. Extra mounting nuts are available. 6 Clippard Instrument Laboratory, Inc

6 STAINLESS STEEL ACCESSORIES Flow Controls Clippard offers a large variety of flow controls and needle valves for adjusting the speed of the cylinder. Several models are available from fine adjustments to coarse adjustments in a variety of mounting configurations. See pages 54 through 57. Quick Exhaust Valves The primary function of a quick exhaust valve is to increase cylinder speed. This also enables the use of smaller directional valves and longer control lines. Offered with several port configurations from #0-32 models up to /4. See pages 59 and 60. Limit Valves A limit valve is the best way to have a mechanical limit to return air signals to control valves or circuits. Clippard offers limit valves in ports ranging from #3-56 up to /8 NPT, high force and heavy duty limits as well as non-contact sensing valves. See Control Valves section. Clippard Instrument Laboratory, Inc

7 5/6 BORE STAINLESS STEEL CYLINDER SSR Options: B, V, S, N Spring Compressed: lbs. Spring At Rest: 0.5 lbs. For bumpers add.250 For S option add * + for each /2" of stroke #0-32 thd. port thd. /4-28 thd. USR Mount: Universal Options: B, V, N Spring Compressed: lbs. Spring At Rest: 0.5 lbs for each /2" of stroke For bumpers add /4-28 thd thd. #0-32 thd. port 3/8-24 thd flats Nuts included, but not shown on drawing SDR UDR Options: B, V, P6, P7, P8, S, N For bumpers add.250 For S option add #5-40 thd. 3/8-24 thd. #0-32 thd stroke 2 mounting holes 0.6 thru stroke #0-32 thd. port Mount: Universal Options: B, V, P2, P3, P4, P5, P6, P7, P8, N For bumpers add thd. 3/8-24 thd. #0-32 thd mounting holes 0.6 thru 0.87 flats 0.25 #0-32 thd. port 3/8-24 thd. Nuts included, but not shown on drawing 8 Clippard Instrument Laboratory, Inc

8 5/6 BORE STAINLESS STEEL CYLINDER SRR Reverse Acting Options: B, V, N Spring Compressed: lbs. Spring At Rest: 0.5 lbs. For bumpers add.250 URR Reverse Acting + stroke thd. 3/8-24 thd Mount: Universal Spring Compressed: lbs. Spring At Rest: 0.5 lbs. Options: B, V, P2, P3, P4, P5, P6, P7, P8, N For bumpers add for each of stroke #0-32 thd mounting holes 0.6 thru #0-32 thd. Nuts included, but not shown on drawing + stroke thd. 3/8-24 thd for each of stroke 2 mounting holes 0.6 thru #0-32 thd /8-24 thd. #0-32 thd. Nuts included, but not shown on drawing FORCE FACTOR The force factor is the nominal area of the cylinder bore size. The chart to the right provides theoretical forces in both the extend and retract stroke of all available bore sizes. These values are theoretical and make no allowance for friction which varies with the bore size. It is recommended that a 25% safety factor be allowed when selecting a cylinder bore for normal load movement. In high speed applications that number should be at least 40%. F P A The extend and retract values differ due to the rod diameter. Bore Size 5/6 /2 5/8 3/4 7/8 -/6 -/4 -/2-3/4 2 2-/2 3 Force Factor - Extend (area) Rod Size /8 3/6 3/6 /4 /4 5/6 3/8 7/6 /2 5/8 5/8 3/4 Rod Area Force Factor - Retract (area) psig - Extend (lbs) psig - Retract (lbs) psig - Extend (lbs) psig - Retract (lbs) psig - Extend (lbs) psig - Retract (lbs) Clippard Instrument Laboratory, Inc

9 5/6 BORE ACCESSORIES MOUNTING NUTS CB-0595 Clevis Bracket 0.56 (2) places Stud Nut Part Across Nut Nut Number Flats Thickness (Thread) N04-28A 7/6 5/32 /4-28 N04-28B 3/8 /8 /4-28 N06-24A 9/6 7/32 3/8-24 N06-24B /2 /8 3/8-24 Rod Nut Part Across Nut Nut Number Flats Thickness (Thread).87 N02-40 /4 3/32 # (2) places RE-0585 Rod End body 0.56 Bronze Bearing 0.87 RC-058 Rod Clevis (2) retaining rings sq #5-40 Thread Body Body Flats #5-40 thd thru both sides Locknut Max. Static Radial Load: 624 lbs. Fits Rod Thread Size: #5-40 FB-059 Foot Bracket FB-0592 Foot Bracket 0.56 mounting holes rad mounting holes rad Clippard Instrument Laboratory, Inc

10 /2 BORE STAINLESS STEEL CYLINDER FSR Mount: Front Spring Compressed: 2 lbs. Spring At Rest: 0.9 lbs. Options: MB, B, H, V, S, N For bumpers add.500 For magnetic bumpers add.82 For S option add.87 sq (2) mounting holes #8-32 thd. x deep #0-32 thd for each /2" of stroke (2) mounting holes #8-32 thd. x 0.87 deep #0-32 thd. SSN Type: Non-Rotating Rod Spring Compressed: 2 lbs. Spring At Rest: 0.9 lbs. Options: MB, B, H, V, S, N For bumpers add.500 For magnetic bumpers add.82 For S option add for each /2" of stroke 0.56 #0-32 thd. 3/8-24 thd. #0-32 thd. port SSR Nuts included, but not shown on drawing Spring Compressed: 2 lbs. Spring At Rest: 0.9 lbs. Options: MB, B, H, V, S, N For bumpers add.500 For magnetic bumpers add.82 For S option add for each /2" of stroke /8-24 thd. #0-32 thd. #0-32 thd. port USN Mount: Universal Type: Non-Rotating Rod Options: MB, B, H, V, P6, N Nuts included, but not shown on drawing Spring Compressed: 2 lbs. Spring At Rest: 0.9 lbs. Bumpers add.500 For magnetic bumpers add for each /2" of stroke #0-32 thd. Clippard Instrument Laboratory, Inc /8-24 thd hex. #0-32 thd /6-20 thd. flats Furnished without nut(s). See Chart on Page 4.

11 /2 BORE STAINLESS STEEL CYLINDER USR Mount: Universal Spring Compressed: 2 lbs. Spring At Rest: 0.9 lbs. Options: MB, B, H, V, P6, N Bumpers add.500 For magnetic bumpers add for each /2" of stroke FDR SDR sq. #0-32 thd. (2) mounting holes #8-32 thd. x deep #0-32 thd. 3/8-24 thd. #0-32 thd /6-20 thd (2) mounting holes #8-32 thd. x 0.87 deep opposite side flats Mount: Front Options: MB, B, V, P6, P7, P8, S, N Bumpers add.500 For magnetic bumpers add.82 For S option add stroke Options: MB, B, V, P6, P7, P8, S, N Furnished without nut(s). See Chart on Page 4. #0-32 thd. both ports For bumpers add.500 For magnetic bumpers add.82 For S option add stroke 0.56 #0-32 thd. port #0-32 thd. #0-32 thd. 7/6-20 thd. flats UDR Mount: Universal Options: MB, B, V, P2, P3, P4, P5, P6, P7, P8, N For bumpers add.500 For magnetic bumpers add stroke #0-32 thd. #0-32 thd. 7/6-20 thd. typ flats Furnished without nut(s). See Chart on Page 4. 2 Clippard Instrument Laboratory, Inc

12 /2 BORE STAINLESS STEEL CYLINDER SDD SRR Reverse Acting URR Reverse Acting Type: Double Rod Options: MB, B, V, P6, P7, P8, N For bumpers add.500 plus stroke #0-32 thd. both ends + stroke (2 x stroke) stroke #0-32 thd. both ports 7/6-20 thd. both ends #0-32 thd for each /2" of stroke #0-32 thd. port 7/6-20 thd. For Magnetic Bumper add.82 Spring Compressed: 2 lbs. Spring At Rest: 0.9 lbs. Options: MB, B, H, V, N For bumpers add.500 For Magnetic Bumper add.82 Mount: Universal Spring Compressed: 2 lbs. Spring At Rest: 0.9 lbs. Options: MB, B, H, V, P6, P7, P8, N For bumpers add For Magnetic Bumper add.82 + stroke for each of stroke #0-32 thd. #0-32 thd flats 7/6-20 thd. typ. Furnished without nut(s). See Chart on Page 4. Clippard Instrument Laboratory, Inc

13 /2 BORE ACCESSORIES MOUNTING NUTS Stud Nut Part Across Nut Nut Number Flats Thickness (Thread) N06-24A 9/6 7/32 3/8-24 N06-24B /2 /8 3/8-24 N07-20 /6 /4 7/6-20 CB-0895 Clevis Bracket Rod Nut Part Across Nut Nut Number Flats Thickness (Thread) N /8 /8 # RE-0885 Rod End body Bronze Bearing RC-088 Rod Clevis thru both sides sq Body #0-32 Body Flats #0-32 thd Lockwasher Locknut Max. Static Radial Load: 624 lbs. Fits Rod Thread Size: #0-32 FB-089 Foot Bracket FB-0892 Foot Bracket rad rad Clippard Instrument Laboratory, Inc

14 5/8 BORE STAINLESS STEEL CYLINDER USN-0- - Mount: Universal Type: Non-Rotating Rod Options: MB, B, H, V, P6, N Spring Compressed: 4 lbs. Spring At Rest:.3 lbs. For bumpers add.500. For magnetic bumpers add for each /2" of stroke #0-32 thd. #0-32 thd. 3/8-24 thd hex. s.s. rod (non-rotating) 7/6-20 thd. USR-0- - Furnished without nut(s). See Chart on Page 8. Mount: Universal Spring Compressed: 4 lbs. Spring At Rest:.3 lbs. Options: MB, B, H, V, P6, N For bumpers add.500. For magnetic bumpers add for each /2" of stroke #0-32 thd. #0-32 thd. 3/8-24 thd /6-20 thd.. SSN-0- - Furnished without nut(s). See Chart on Page 8. Type: Non-Rotating Rod Options: MB, B, H, V, S, N Spring Compressed: 4 lbs. Spring At Rest:.3 lbs. For bumpers add.500. For magnetic bumpers add for each /2" of stroke #0-32 thd. 3/8-24 thd. 3/6 hex. s.s. rod (non-rotating) #0-32 thd. SSR-0- - Spring Compressed: 4 lbs. Spring At Rest:.3 lbs. Options: MB, B, H, V, S, N For bumpers add.500. For magnetic bumpers add for each /2" of stroke #0-32 thd. 3/8-24 thd. #0-32 thd. Clippard Instrument Laboratory, Inc

15 5/8 BORE STAINLESS STEEL CYLINDER FSR-0- - Mount: Front Spring Compressed: 4 lbs. Spring At Rest:.3 lbs. Options: MB, B, H, V, S, N For bumpers add.500. For magnetic bumpers add.82 For S option add sq for each /2" of stroke (2) mounting holes #8-32 thd. x deep #0-32 thd (2) mounting holes #8-32 thd. x 0.87 deep #0-32 thd. FDR-0- - Mount: Front Options: MB, B, V, P6, P7, P8, S, N sq Furnished without nut(s). See Chart on Page stroke 0.56 For bumpers add.500 For magnetic bumpers add For S option add.87 (2) mounting holes #8-32 thd. x deep #0-32 thd. 7/6 #0-32 thd. both ports (2) mounting holes #8-32 thd deep opposite side SDR-0- - Options: MB, B, V, P6, P7, P8, S, N For bumpers add.500 For magnetic bumpers add.82 For S option add.87 UDR-0- - #0-32 thd. Mount: Universal Options: MB, B, V, P2, P3, P4, P5, P6, P7, P8, N stroke 0.56 #0-32 thd. both ports 7/6-20 thd. Standard Stroke Lengths: /2,, -/2, 2, 3, stroke For bumpers add.500 For magnetic bumpers add #0-32 thd #0-32 thd. both ports 7/6-20 thd. both ends Furnished without nut(s). See Chart on Page 8. 6 Clippard Instrument Laboratory, Inc

16 5/8 BORE STAINLESS STEEL CYLINDER SDD-0- - Type: Double Rod Options: MB, B, V, P6, P7, P8, N Standard Stroke Lengths: /2,, -/2, 2, 3, 4 For bumpers add.500 For magnetic bumpers add (2 x stroke) SRR-0- - Reverse Acting Options: MB, B, H, V, N + stroke #0-32 thd. both ends stroke #0-32 thd. both ports 7/6-20 thd. both ends Spring Compressed: 4 lbs. Spring At Rest:.3 lbs. For bumpers add.500 For magnetic bumpers add.82 + stroke #0-32 thd for each /2" of stroke 7/6-20 thd. #0-32 thd URR-0- - Reverse Acting Mount: Universal Options: MB, B, H, V, P6, N Spring Compressed: 4 lbs. Spring At Rest:.3 lbs. For bumpers add.500 For magnetic bumpers add.82 + stroke 9/ for each /2" of stroke #0-32 thd. both ends #0-32 thd /6-20 thd. both ends Furnished without nut(s). See Chart on Page 8. Clippard Instrument Laboratory, Inc

17 5/8 BORE ACCESSORIES MOUNTING NUTS Stud Nut Part Across Nut Nut Number Flats Thickness (Thread) N06-24A 9/6 7/32 3/8-24 N06-24B /2 /8 3/8-24 N07-20 /6 /4 7/6-20 CB-0895 Clevis Bracket Rod Nut Part Across Nut Nut Number Flats Thickness (Thread) N /8 /8 # RE-0885 Rod End body Bronze Bearing RC-088 Rod Clevis thru both sides sq Body #0-32 Body Flats #0-32 thd Lockwasher Locknut Max. Static Radial Load: 624 lbs. Fits Rod Thread Size: #0-32 FB-089 Foot Bracket FB-0892 Foot Bracket rad rad Clippard Instrument Laboratory, Inc

18 3/4 BORE STAINLESS STEEL CYLINDER FSR-2- - Mount: Front Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, B, H, V, S, N For bumpers add.500. For magnetic bumpers add.82 For S option add for each " of stroke sq. /4-28 thd. (2) mounting holes #0-32 thd. x deep /8-27 NPT (2) mounting holes x 0.28 deep counter bore thru /4-20 thd. x deep from far side SSN-2- - Type: Non-Rotating Rod Options: MB, B, H, V, S, N Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. For bumpers add.500. For magnetic bumpers add.82 For S option add for each " of stroke /4-28 thd. /2-20 thd. /4 hex. s.s. rod (non-rotating) /8-27 NPT SSR-2- - Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, B, H, V, S, N For bumpers add.500. For magnetic bumpers add.82 For S option add for each " of stroke /4-28 thd. /2-20 thd. /8-27 NPT TSR-2- - Mount: Trunnion Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, B, H, V, S, N For bumpers add.500. For magnetic bumpers add.82 For S option add for each " of stroke sq..750 /4-28 thd /8-27 NPT Clippard Instrument Laboratory, Inc

19 3/4 BORE STAINLESS STEEL CYLINDER USN-2- - Mount: Universal Type: Non-Rotating Rod Options: MB, B, H, V, P6, N Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. For bumpers add.500. For magnetic bumpers add for each " of stroke 0.28 USR-2- - /4-28 thd. /2-20 thd. hex. s.s. rod (non-rotating) 5/8-8 thd. Furnished without nut(s). See Chart on Page 24. Mount: Universal Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, B, H, V, P6, N For bumpers add.500. For magnetic bumpers add for each " of stroke /4-28 thd. /2-20 thd. 5/8-8 thd. Furnished without nut(s). See Chart on Page 24. FDR-2- - Mount: Front Options: MB, B, W, V, P6, P7, P8, S, N, 5, stroke For bumpers add.500 For magnetic bumpers add For S option add sq. (2) mounting holes #0-32 thd. x 5/6 deep /4-28 thd. /8-27 NPT both ports (2) mounting holes x 0.28 deep counter bore thru /4-20 thd. x deep from far side TDR-2- - Mount: Trunnion Options: MB, B, W, V, S, N, 5, Furnished without nut(s). See Chart on Page stroke For bumpers add.500 For magnetic bumpers add For S option add.437 sq. /4-28 thd /8-27 NPT both ports Clippard Instrument Laboratory, Inc

20 3/4 BORE STAINLESS STEEL CYLINDER UDR , 6, 8, 0, 2 Type: Rotating rod Options: C, F, R, MB, B, W, V, P2, P3, P4, P5, P6, P7, P8, M, N For bumpers add.500 For magnetic bumpers add.82 For magnet add stroke 0.28 /4-28 thd. /8-27 NPT both ports 5/8-8 thd. both ends SDR-2- -, 5, 6 Options: C, F, R, MB, B, W, V, P6, P7, P8, S, M, N Furnished without nut(s). See Chart on Page stroke For bumpers add.500 For magnetic bumpers add.82 For C, F, R & S options add.437 For magnet add /4-28 thd. /8-27 NPT both ports 5/8-8 thd. SDD-2- - Nuts included, but not shown on drawing For C, F, & R options use side ported rear head Standard Stroke Lengths:, 2, 3, 4, 5, 6 Type: Double Rod Options: C, F, MB, B, W, V, P6, P7, P8, M, N Bumpers add.500. For magnetic bumpers add.82 For CM, FM add (2 x stroke) + stroke 4" + stroke /4-28 thd. both ends /8-27 NPT both ports 5/8-8 thd. both ends SDH-2- - Type: Hollow Rod Options: C, F, MB, B, W, V, P6, P7, P8, M, N Standard Stroke Lengths:, 2, 3, 4, 5, 6 Nuts included, but not shown on drawing For bumpers add.500 For magnetic bumpers add.82 For CM, FM add.32 + stroke /4-28 thd. both ends thru (2*stroke) 4" + stroke /8-27 NPT both ports 5/8-8 thd. both ends Clippard Instrument Laboratory, Inc Nuts included, but not shown on drawing 2

21 3/4 BORE STAINLESS STEEL CYLINDER SRR-2- - Reverse Acting Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, B, H, W, V, N For bumpers add.375 For magnetic bumpers add stroke /4-28 thd /8-27 NPT 5/8-8 thd for each " of stroke URR-2- - Reverse Acting Mount: Universal Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, B, H, W, V, P6, N For bumpers add.500 For magnetic bumpers add.82 + stroke for each " of stroke /4-28 thd. /8-27 NPT 5/8-8 thd. both ends SFD-2- -, Spring Bias Furnished without nut(s). See Chart on Page 24. Type: Double Rod Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, B, H, W, V, P6, P7, P8, N For bumpers add for each " of stroke For magnetic bumpers add stroke for each " of stroke /4-28 thd. both ends /8-27 NPT both ports SBR-2- -, Rear Spring Bias 5/8-8 thd. both ends Nuts included, but not shown on drawing Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, B, H, W, V, P6, P7, P8, S, N For bumpers add.375 For magnetic bumpers add.687 For S option add stroke for each " of stroke /4-28 thd. /8-27 NPT both ports 5/8-8 thd. 22 Clippard Instrument Laboratory, Inc

22 3/4 BORE STAINLESS STEEL CYLINDER SFR-2- -, Front Spring Bias Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, B, H, W, V, P6, P7, P8, S, N For bumpers add.375 For magnetic bumpers add.687 For S option add for each " of stroke /4-28 thd. 5/8-8 thd. /8-27 NPT both ports UBR-2- -, Rear Spring Bias Mount: Universal Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, B, H, W, V, P2, P3, P4, P5, P6, P7, P8, N For bumpers add.375 For magnetic bumpers add stroke for each " of stroke 0.28 /4-28 thd. /8-27 NPT both ports 5/8-8 thd. both ends UFR-2- -, Front Spring Bias Furnished without nut(s). See Chart on Page 24. Mount: Universal Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, B, H, W, V, P2, P3, P4, P5, P6, P7, P8, N For bumpers add.375 For magnetic bumpers add for each " of stroke 0.28 /4-28 thd. /8-27 NPT both ports 5/8-8 thd. both ends Furnished without nut(s). See Chart on Page 24. CAD 2D & 3D Models Available 2D & 3D CAD models of all Clippard stainless steel cylinders are now available via A wide range of formats are offered for your convenience. Clippard s on-line, state-of-the-art cylinder configurator allows users to build their own cylinder exactly to the required specifications, and then view the details, drawings, CAD models, pricing and much more! Clippard Instrument Laboratory, Inc

23 3/4 BORE ACCESSORIES MOUNTING NUTS Stud Nut Part Across Nut Nut Number Flats Thickness (Thread) N /4 5/6 /2-20 N0-8 5/6 3/8 5/8-8 CB-795 Clevis Bracket Rod Nut Part Across Nut Nut Number Flats Thickness (Thread) N04-28A 7/6 5/32 /4-28 N04-28B 3/8 /8 / RE-285 Rod End body Bronze Bearing RC-28 Rod Clevis sq dia /4-28 Body Body Flats -thru both sides /4-28 thd Lockwasher Locknut Max. Static Radial Load: 2545 lbs. Fits Rod Thread Size: /4-28 FB-29 Foot Bracket FB-79 Foot Bracket rad rad Clippard Instrument Laboratory, Inc

24 7/8 BORE STAINLESS STEEL CYLINDER SSN-4- - Type: Non-Rotating Rod Options: MB, H, V, S, N Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Bumpers are standard. For S option add for each " of stroke flats /8-8 thd. /4-28 thd /8-27 NPT SSR-4- - Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, H, V, S, N Bumpers are standard. For S option add for each " of stroke flats /4-28 thd. 5/8-8 thd /8-27 NPT USN-4- - Mount: Universal Type: Non-Rotating Rod Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, H, V, P2, P3, P4, P5, P6, P7, P8, N Bumpers are standard for each " of stroke flats /4-28 thd. /8-27 NPT 5/8-8 thd. both ends /4 USR-4- - Furnished without nut(s). See Chart on Page 28. Mount: Universal Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, H, V, P2, P3, P4, P5, P6, P7, P8, N Bumpers are standard. Furnished without nut(s) See chart on page for each " of stroke flats 5/6 Clippard Instrument Laboratory, Inc /4-28 thd. /8-27 NPT 5/8-8 thd. both ends Furnished without nut(s). See Chart on Page

25 7/8 BORE STAINLESS STEEL CYLINDER SDR-4- -, 5, 6 Bumpers are standard Options: C, F, R, MB, W, V, P6, P7, P8, S, N stroke For C, F, R and S option add flats /4-28 thd. /8-27 NPT both ports UDR /8-8 thd. For C, F, & R options use side ported rear head Mount: Universal, 5, 6 Options: C, F, R, MB, W, V, P2, P3, P4, P5, P6, P7, P8, N stroke 0.28 Furnished without nut(s) See chart on page 28 Bumpers are standard 0.28 fla SDD-4- - /4-28 thd. Type: Double Rod Options: C, F, MB, W, V, P6, P7, P8, N /8-8 thd. both ends /8-27 NPT both ports Standard Stroke Lengths:, 2, 3, 4, 5, (2 x stroke) stroke + stroke Furnished without nut(s). See Chart on Page 28. Bumpers are standard /4-28 thd. both ends /8-27 NPT both ports /8-8 thd. both ends SDH-4- - Standard Stroke Lengths:, 2, 3, 4, 5, 6 Type: Hollow Rod Options: C, F, MB, W, V, P6, P7, P8, N + stroke (2 x stroke) Nuts included, but not shown on drawing stroke Bumpers are standard /4-28 thd. both ends thru 5/8-8 thd. both ends /8-27 NPT both ports Nuts included, but not shown on drawing 26 Clippard Instrument Laboratory, Inc

26 7/8 BORE STAINLESS STEEL CYLINDER SRR-4- - Reverse Acting Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, H, W, V, N Bumpers are standard + stroke for each of stroke /4-28 thd. 5/8-8 thd /8-27 NPT URR-4- - Reverse Acting Mount: Universal Spring Compressed: 6 lbs. Spring At Rest: 3 lbs. Options: MB, H, W, V, P6, P7, P8, N Bumpers are standard + stroke /4-28 thd for each " of stroke /8-27 NPT flats J-Series Exhaust Valve In a typical application the exhaust valve is installed in the inlet of a spring return or double acting pneumatic cylinder. Supply air from a control valve is directed into the inlet port of the exhaust valve. The Buna-N poppet seals the exhaust port and allows air to flow from the outlet port of the valve into the cylinder. The pressurized air pushes against the piston and extends the rod, compressing the spring, until full rod extension is achieved. When the control valve exhausts air from the exhaust valve inlet port, the Buna- N poppet shifts to seal the inlet port and open the exhaust port to the cylinder. The pressurized air is allowed to exhaust directly through the exhaust valve to atmosphere. Normally the air must travel back through the long air line to the control valve to exhaust. By mounting the exhaust valve directly on the cylinder, the piston retracts quickly since the distance to atmosphere is very short and unrestricted. Inlet Port Outlet Port from control valve control valve signal removed 5/8-8 thd. both ends Furnished without nut(s). See Chart on Page 28. Poppet Exhaust Valve Exhaust Port Cylinder Extends Cylinder Retracts - Fast! exhausts to atmosphere Clippard Instrument Laboratory, Inc

27 7/8 BORE ACCESSORIES MOUNTING NUTS Stud Nut Part Across Nut Nut Number Flats Thickness (Thread) N0-8 5/6 3/8 5/8-8 Rod Nut Part Across Nut Nut Number Flats Thickness (Thread) N04-28A 7/6 5/32 /4-28 CB Clevis Bracket N04-28B 3/8 /8 /4-28 RE-285 Rod End body Bronze Bearing RC-28 -thru both sides Rod Clevis 0.50 sq dia /4-28 Body Body Flats FB-79 /4-28 thd Foot Bracket Lockwasher Locknut Max. Static Radial Load: 2545 lbs. Fits Rod Thread Size: / rad Clippard Instrument Laboratory, Inc

28 /6 BORE STAINLESS STEEL CYLINDER FSR-7- - Mount: Front Spring Compressed: 7 lbs. Spring At Rest: 2 lbs. Options: MB, B, H, V, S, N for each " of stroke 0.87 For S option add sq. SSN /6-24 thd. (2) mounting holes #0-32 thd. x deep for each " of stroke /8-27 NPT (2) mounting holes x 0.28 deep counter bore thru /4-20 thd. x deep from far side Type: Non-Rotating Rod Options: MB, B, H, V, S, N Spring Compressed: 7 lbs. Spring At Rest: 2 lbs. For S option add SSR /6-24 thd /8-8 thd. hex. s.s. rod (non-rotating) for each " of stroke 0.87 /8-27 NPT Spring Compressed: 7 lbs. Spring At Rest: 2 lbs. Options: MB, B, H, V, S, N.25 5/6-24 thd. 5/8-8 thd. /8-27 NPT TSR-7- - Mount: Trunnion Spring Compressed: 7 lbs. Spring At Rest: 2 lbs. Options: MB, B, H, V, S, N for each " of stroke 0.87 For S option add sq. 2 5/6-24 thd. /8-27 NPT Clippard Instrument Laboratory, Inc

29 /6 BORE STAINLESS STEEL CYLINDER USN-7- - Mount: Universal Type: Non-Rotating Rod Options: MB, B, H, V, P6, N Spring Compressed: 7 lbs. Spring At Rest: 2 lbs for each " of stroke USR /6-24 thd. 5/8-8 thd. both ends /8-27 NPT hex. s.s. rod (non-rotating) for each " of stroke 0.28 Furnished without nut(s). See Chart on Page 34. Mount: Universal Spring Compressed: 7 lbs. Spring At Rest: 2 lbs. Options: MB, B, H, V, P6, N /6-24 thd. 5/8-8 thd. both ends /8-27 NPT FDR Furnished without nut(s). See Chart on Page 34. Mount: Front, 5, 6 Options: MB, B, W, V, P6, P7, P8, S, N stroke For S option add /6-24 thd. (2) mounting holes #0-32 thd. x deep /8-27 NPT both ports.250 sq. (2) mounting holes x.28 deep counter bore thru /4-20 thd. x deep from far side SDR-7- -, 5, 6 Options: C, F, R, MB, B, W, V, P6, P7, P8, S, N stroke 0.87 For C, F, R or S option add /8-8 thd. /8-27 NPT both ports 5/6-24 thd. For C, F, & R options use side ported rear head 30 Clippard Instrument Laboratory, Inc

30 /6 BORE STAINLESS STEEL CYLINDER TDR-7- - Mount: Trunnion, 5, 6 Options: MB, B, W, V, S, N stroke 0.87 For S option add sq. 2 5/6-24 thd. /8-27 NPT both ports UDR-7- - Mount: Universal 5, 6, 8, 0, 2 Options: C, F, R, MB, B, W, V, P2, P3, P4, P5, P6, P7, P8, N 4" + stroke /6-24 thd. /8-27 NPT both ports 5/8-8 thd. both ends Furnished without nut(s). See Chart on Page 34. SDD-7- - Standard Stroke Lengths:, 2, 3, 4, 5, 6 Type: Double Rod Options: C, F, R, MB, B, W, V, P6, P7, P8, N (2 x stroke) stroke + stroke.25 5/6-24 thd. both ends /8-27 NPT both ports 5/8-8 thd. both ends Nuts included, but not shown on drawing SDH-7- - Standard Stroke Lengths:, 2, 3, 4, 5, 6 Type: Hollow Rod Options: C, F, MB, B, W, V, P6, P7, P8, N + stroke (2 x stroke) stroke /6-24 thd. both ends /8-27 NPT both ports 5/8-8 thd. both ends hollow rod ( thru) Nuts included, but not shown on drawing Clippard Instrument Laboratory, Inc

31 /6 BORE STAINLESS STEEL CYLINDER SRR-7- - Reverse Acting Spring Compressed: 7 lbs. Spring At Rest: 2 lbs. Options: MB, B, H, W, V, N + stroke for each " of stroke 5/6-24 thd. 5/8-8 thd. /8-27 NPT.25 URR-7- - Reverse Acting for each " of stroke + stroke 0.53 Nuts included, but not shown on drawing Mount: Universal Spring Compressed: 7 lbs. Spring At Rest: 2 lbs. Options: MB, B, H, W, V, P6, N /6-24 thd. /8-27 NPT 5/8-8 thd. both ends SFD-7- - Spring Bias SBR-7- - Rear Spring Bias Type: Double Rod Spring Compressed: 7 lbs. Spring At Rest: 2 lbs. Options: MB, B, H, W, V, P6, P7, P8, N + stroke 5/6-24 thd. both ends for each " of stroke Furnished without nut(s). See Chart on Page for each " of stroke /8-27 NPT both ports 5/8-8 thd. both ends Spring Compressed: 7 lbs. Spring At Rest: 2 lbs. Options: MB, B, H, W, V, P6, P7, P8, S, N.25 Nuts included, but not shown on drawing For S option add stroke 0.50 for each " of stroke /6-24 thd. 5/8-8 thd. /8-27 NPT both ports 32 Clippard Instrument Laboratory, Inc

32 /6 BORE STAINLESS STEEL CYLINDER SFR-7- -, Spring Bias Spring Compressed: 7 lbs. Spring At Rest: 2 lbs. Options: MB, B, H, W, V, P6, P7, P8, S, N For S option add.250 for each " of stroke /6-24 thd. 5/8-8 thd. /8-27 NPT both ports UBR-7- -, Rear Spring Bias + stroke for each " of stroke Mount: Universal Spring Compressed: 7 lbs. Spring At Rest: 2 lbs. Options: MB, B, H, W, V, P2, P3, P4, P5, P6, P7, P8, N UFR-7- - Front Spring Bias 5/6-24 thd. 5/8-8 thd. both ends 0.53 /8-27 NPT both ports for each " of stroke 0.28 Furnished without nut(s). See Chart on Page 34. Mount: Universal Spring Compressed: 7 lbs. Spring At Rest: 2 lbs. Options: MB, B, H, W, V, P2, P3, P4, P5, P6, P7, P8, N /6-24 thd..25 /8-27 NPT both ports 5/8-8 thd. both ends Furnished without nut(s). See Chart on Page 34. Clippard Instrument Laboratory, Inc

33 /6 BORE ACCESSORIES MOUNTING NUTS Stud Nut Part Across Nut Nut Number Flats Thickness (Thread) N0-8 5/6 3/8 5/8-8 Rod Nut Part Across Nut Nut Number Flats Thickness (Thread) N05-24 /2 3/6 5/6-24 CB-795 Clevis Bracket RE-785 Rod End body Bronze Bearing RC-78 Rod Clevis Body sq /6-24 Lockwasher Body Flats - thru both sides.87 5/6-24 thd Locknut Max. Static Radial Load: 3200 lbs. Fits Rod Thread Size: 5/6-24 FB-79 Foot Bracket rad Clippard Instrument Laboratory, Inc

34 /4 BORE STAINLESS STEEL CYLINDER Note: The /4 bore is also available with a 7/6-20 threaded rod. Order -LR option. SSN Type: Non-Rotating Rod Spring Compressed: 0 lbs. Spring At Rest: 4.5 lbs. Options: MB, B, H, V, S, N For S option add for each " of stroke.32 3/8-24 thd. both ends 3/4-6 thd. 3/8 hex. s.s. rod (non-rotating) /8-27 NPT SSR Spring Compressed: 0 lbs. Spring At Rest: 4.5 lbs. Options: MB, B, H, V, S, N For S option add for each " of stroke.32 3/8-24 thd. both ends 3/4-6 thd. /8-27 NPT USN USR Mount: Universal Type: Non-Rotating Rod Spring Compressed: 0 lbs. Spring At Rest: 4.5 lbs. Options: MB, B, H, V, P2, P3, P4, P5, P6, P7, P8, N for each " of stroke 3/4-6 thd. both ends 3/8 hex. s.s. rod (non-rotating) 3/8-24 thd for each " of stroke /8-27 NPT Mount: Universal Spring Compressed: 0 lbs. Spring At Rest: 4.5 lbs. Options: MB, B, H, V, P2, P3, P4, P5, P6, P7, P8, N Furnished without nut(s). See Chart on Page /8-24 thd. 3/4-6 thd. both ends /8-27 NPT Clippard Instrument Laboratory, Inc Furnished without nut(s). See Chart on Page

35 /4 BORE STAINLESS STEEL CYLINDER Note: The /4 bore is also available with a 7/6-20 threaded rod. Order -LR option. SDR-20- -, 5, 6 Options: C, F, R, MB, B, W, V, P6, P7, P8, S, N stroke For C, F, R and S option add UDR /8-24 thd. /8-27 NPT both ports 3/4-6 thd. For C, F, & R options use side ported rear head Mount: Universal 6, 8, 0, 2 Options: C, F, R, MB, B, W, V, P2, P3, P4, P5, P6, P7, P8, N stroke /4-6 thd. both ends 3/8-24 thd. /8-27 NPT both ports SDD Furnished without nut(s). See Chart on Page 38. Standard Stroke Lengths:, 2, 3, 4, 5, 6 Type: Double Rod Options: C, F, MB, B, W, V, P6, P7, P8, N (2 x stroke) stroke + stroke.32 3/8-24 thd. both ends /8-27 NPT both ports 3/4-6 thd. both ends SRR Reverse Acting Spring Compressed: 0 lbs. Spring At Rest: 4.5 lbs. Options: MB, B, H, W, V, N + stroke Nuts included, but not shown on drawing for each " of stroke 3/8-24 thd. 3/4-6 thd. /8-27 NPT.32 Nuts included, but not shown on drawing 36 Clippard Instrument Laboratory, Inc

36 /4 BORE STAINLESS STEEL CYLINDER Note: The /4 bore is also available with a 7/6-20 threaded rod. Order -LR option. URR Reverse Acting Mount: Universal Spring Compressed: 0 lbs. Spring At Rest: 4.5 lbs. Options: MB, B, H, W, V, P6, N + stroke 3/8-24 thd for each " of stroke /8-27 NPT both ports 3/4-6 thd. both ends Furnished without nut(s). See Chart on Page 38. APPLICATION STORY ap pli ca tion \ap-l - kâ-sh n\ n : the act of applying 2 : assiduous attention 3 : REQUEST; also : a form used in making a request 4 : something placed or spread on a surface 5 : capacity for use e e Clippard Applications Have Gone to the Birds Pneumatic automation plays a role on the roof tops of Clippard. Over time, pigeons become unruffled by the presence of a motionless plastic owl. By automating several owls throughout the area to pop up out of 8 inch PVC pipes, the pigeon problem has flown away. While this application only requires a single acting cylinder, they tend to be longer than double acting cylinders of the same stroke. To fit the cylinder inside of the owl and have enough stroke to raise it fully, these wise old birds used double acting cylinders with a little circuitry to make them act like single acting cylinders. Regulator Normally Open Air Piloted Valve Overall Length: 2.750" (SSR-2-2) Check Valve Vol. Overall Length: 4.968" (SDR-2-2) Vol. Check Valve Single signal line & supply line - or - Clippard Instrument Laboratory, Inc

37 /4 BORE ACCESSORIES MOUNTING NUTS Stud Nut Part Across Nut Nut Number Flats Thickness (Thread) N2-6 3/32 27/64 3/4-6 Rod Nut Part Across Nut Nut Number Flats Thickness (Thread) N06-24A 9/6 7/32 3/8-24 CB Clevis Bracket.56 N06-24B /2 /8 3/8-24 RE-2085 Rod End body Bronze Bearing RC-208 Rod Clevis sq. -thru both sides Body /8-24 Body Flats FB-249 3/8-24 thd Foot Bracket Lockwasher Locknut Max. Static Radial Load: 3950 lbs. Fits Rod Thread Size: 3/ rad Clippard Instrument Laboratory, Inc

38 /2 BORE STAINLESS STEEL CYLINDER CSN Mount: Clevis Type: Non-Rotating Rod Options: MB, B, H, V, P6, N Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs for each " of stroke.562 CSR /4-6 thd. /8-27 NPT 7/6 hex. s.s. rod (non-rotating) 7/6-20 thd. Furnished without nut(s). See Chart on Page 46. Mount: Clevis Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, V, P6, N for each " of stroke.562 ESN /4-6 thd. 7/6-20 thd. /8-27 NPT Furnished without nut(s). See Chart on Page 46. Mount: End Type: Non-Rotating Rod Options: MB, B, H, V, N Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs for each " of stroke.562 ESR /4-6 thd. both ends /8-27 NPT hex. s.s. rod (non-rotating) 7/6-20 thd. Nuts included, but not shown on drawing Mount: End Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, V, N for each " of stroke.562 7/6-20 thd. Clippard Instrument Laboratory, Inc /4-6 thd. both ends /8-27 NPT 39

39 /2 BORE STAINLESS STEEL CYLINDER FSR Mount: Front Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, V, S, N for each " of stroke For S option add sq. 7/6-20 thd. (2) mounting holes /4-20 thd. x deep (2) mounting holes x.32 deep counter bore thru 5/6-8 thd.- deep from far side /8-27 NPT both ports SSN Type: Non-Rotating Rod Options: MB, B, H, V, S, N Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs for each " of stroke For S option add SSR /6-20 thd. 3/4-6 thd hex. s.s. rod (non-rotating) Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, V, S, N For S option add for each " of stroke /4-6 thd. 7/6-20 thd. TSR Mount: Trunnion Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, V, S, N for each " of stroke For S option add sq. 7/6-20 thd..062 /8-27 NPT both ports 40 Clippard Instrument Laboratory, Inc

40 /2 BORE STAINLESS STEEL CYLINDER CDR Mount: Clevis 6, 8, 0, 2 Options: C, F, R, MB, B, W, V, P2, P3, P4, P5, P6, P7, P8, N 9/ stroke.562 EDR /8-27 NPT both ports 3/4-6 thd. 7/6-20 thd. Furnished without nut(s). See Chart on Page 46. Mount: End, 6, 8, 0, 2 Options: C, F, R, MB, B, W, V, P6, P7, P8, N stroke.562 /8-27 NPT both ports 7/6-20 thd. 3/4-6 thd. both ends Nuts included, but not shown on drawing FDR Mount: Front, 5, 6 Options: MB, B, W, V, P6, P7, P8, S, N stroke.562 For S option add sq. 7/6-20 thd. (2) mounting holes /4-20 thd. x deep /8-27 NPT both ports (2) mounting holes X deep counter bore thru 5/6-8 thd.-/2 deep from far side SDR-24- -, 6, 8, 0, 2 Options: C, F, R, MB, B, W, V, P6, P7, P8, S, N stroke For C, F, R and S option add /6-20 thd. 3/4-6 thd. Clippard Instrument Laboratory, Inc /8-27 NPT both ports For C, F, & R options use side ported rear head 4

41 /2 BORE STAINLESS STEEL CYLINDER TDR Mount: Trunnion, 5, 6 Options: MB, B, W, V, S, N stroke For S option add /6-20 thd..062 /8-27 NPT both ports.750 sq. SDD CRR Reverse Acting Standard Stroke Lengths:, 2, 3, 4, 5, 6, 8, 0, 2 Type: Double Rod Options: C, F, MB, B, W, V, P6, P7, P8, N + stroke /6-20 thd. both ends (2 x stroke) stroke /8-27 NPT both ports /4-6 thd. both ends (-4 thd. on cr version) Mount: Clevis Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, W, V, P6, P7, P8, N.562 Nuts included, but not shown on drawing + stroke for each " of stroke ERR Reverse Acting 7/6-20 thd. /8-27 NPT both ports vent 3/4-6 thd..562 Furnished without nut(s). See Chart on Page 46. Mount: End Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, W, V, N for each " of stroke + stroke /6-20 thd. /8-27 NPT both ports.562 vent 3/4-6 thd. both ends Nuts included, but not shown on drawing 42 Clippard Instrument Laboratory, Inc

42 /2 BORE STAINLESS STEEL CYLINDER FRR Reverse Acting Mount: Front Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, W, V, N stroke for each " of stroke.562 7/6-20 thd. (2) mounting holes /4-20 thd. x deep /8-27 NPT.750 sq. (2) mounting holes x deep counter bore thru 5/6-8 thd.- deep from far side SRR Reverse Acting Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, W, V, N + stroke for each " of stroke.562 CBR-24- -, Spring Bias 7/6-20 thd. 3/4-6 thd. /8-27 NPT both ports Mount: Clevis Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, W, V, P2, P3, P4, P5, P6, P7, P8, N + stroke for each " of stroke /6-20 thd. 3/4-6 thd. /8-27 NPT both ports CFR-24- -, Front Spring Bias Mount: Clevis Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, W, V, P2, P3, P4, P5, P6, P7 P8, N Furnished without nut(s). See Chart on Page for each " of stroke.562 7/6-20 thd. 3/4-6 thd. /8-27 NPT both ports Clippard Instrument Laboratory, Inc Furnished without nut(s). See Chart on Page

43 /2 BORE STAINLESS STEEL CYLINDER EBR-24- -, Rear Spring Bias Mount: End Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, W, V, P6, P7, P8, N + stroke for each " of stroke /6-20 thd. /8-27 NPT both ports 3/4-6 thd. both ends EFR-24- -, Front Spring Bias Nuts included, but not shown on drawing Mount: End Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, W, V, P6, P7, P8, N for each " of stroke SFD-24- -, Front Spring Bias 7/6-20 thd. /8-27 NPT both ports 3/4-6 thd. both ends for each " of stroke Nuts included, but not shown on drawing Type: Double Rod Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, W, V, P6, P7, P8, N + stroke for each " of stroke SBR-24- -, Rear Spring Bias 7/6-20 thd. both ends /8-27 NPT both ports 3/4-6 thd. both ends Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, W, V, P6, P7, P8, S, N For S option add for each " of stroke + stroke Nuts included, but not shown on drawing.562 7/6-20 thd. /8-27 NPT both ports 3/4-6 thd. Nuts included, but not shown on drawing 44 Clippard Instrument Laboratory, Inc

44 /2 BORE STAINLESS STEEL CYLINDER SFR-24- -, Front Spring Bias Spring Compressed: 0 lbs. Spring At Rest: 4 /2 lbs. Options: MB, B, H, W, V, P6, P7, P8, S, N For S option add for each " of stroke /6-20 thd. /8-27 NPT both ports 3/4-6 thd. Pneumatic Stapler Clippard MFC-3AK Miniature Flow Control Clippard SSN-2-3/4 Bore Stainless Steel Cylinder Clippard Modular Valve Circuit with Adjustable Time Delays and Pressure Bleed Pilot Clippard Polyurethane Hose Clippard MWV- Whisker Valve (senses presence of paper edge to actuate stapler) Simplicity, long life, low cost, ease of maintenance and high power are combined in this unique office stapler application. Clippard Instrument Laboratory, Inc

45 /2 BORE ACCESSORIES MOUNTING NUTS Stud Nut Part Across Nut Nut Number Flats Thickness (Thread) N2-6 3/32 27/64 3/4-6 Rod Nut Part Across Nut Nut Number Flats Thickness (Thread) N07-20 /6 /4 7/6-20 CB-2495 Clevis Bracket RE-2485 Rod End body Bronze Bearing RC-248 Rod Clevis.82 Body.28 sq. -thru both sides dia 7/6-20 Body Flats Lockwasher.687 7/6-20 thd. Locknut Max. Static Radial Load: 4,300 lbs. Fits Rod Thread Size: 7/6-24 FB-249 Foot Bracket rad Clippard Instrument Laboratory, Inc

46 3/4 BORE STAINLESS STEEL CYLINDER SSN Type: Non-Rotating Rod Options: MB, V, S, N Spring Compressed: 24 lbs. Spring At Rest: lbs. Bumpers are standard For S option add for each " of stroke SSR Options: MB, V, S, N /2-20 thd. -4 thd. /2 hex. s.s. rod (non-rotating) /4-8 NPT Spring Compressed: 24 lbs. Spring At Rest: lbs. Bumpers are standard For S option add for each " of stroke /2-20 thd. -4 thd. /4-8 NPT USN Mount: Universal Type: Non-Rotating Rod Spring Compressed: 24 lbs. Spring At Rest: lbs. Options: MB, V, P2, P3, P4, P5, P6, P7, P8, N Bumpers are standard for each " of stroke /2-20 thd. -4 thd. hex. s.s. rod (non-rotating) /4-8 NPT.82 USR Mount: Universal Spring Compressed: 24 lbs. Spring At Rest: lbs. Options: MB, V, P2, P3, P4, P5, P6, P7, P8, N Bumpers are standard Furnished without nut(s). See Chart on Page for each " of stroke Clippard Instrument Laboratory, Inc /2-20 thd. -4 thd. both ends.82 /4-8 NPT Furnished without nut(s). See Chart on Page

47 3/4 BORE STAINLESS STEEL CYLINDER SDR UDR-28- -, 5, 6 Bumpers are standard Options: C, F, R, MB, W, V, P6, P7, P8, S, N For C, F, R and S option add stroke /2-20 thd thd. /4-8 NPT both ports stroke , 6, 8, 0, 2 Mount: Universal Options: C, F, R, MB, W, V, P2, P3, P4, P5, P6, P7, P8, N For C, F, & R options use side ported rear head Bumpers are standard.03 SDD stroke /2-20 thd. Type: Double Rod Options: C, F, MB, W, V, P6, P7, P8, N /4-8 NPT both ports -4 thd. both ends (2 x stroke) stroke Furnished without nut(s). See Chart on Page 50. Standard Stroke Lengths:, 2, 3, 4, 5, 6, 8, 0, 2 Bumpers are standard SRR Reverse Acting.03 Options: MB, W, V, N.03 /4-8 NPT both ports thd. both ends /2-20 thd. both ends Nuts included, but not shown on drawing Spring Compressed: 24 lbs. Spring At Rest: lbs stroke for each " of stroke Bumpers are standard /2-20 thd. -4 thd. /4-8 NPT Clippard Instrument Laboratory, Inc

48 3/4 BORE STAINLESS STEEL CYLINDER URR Reverse Acting Mount: Universal Spring Compressed: 24 lbs. Spring At Rest: lbs. Options: MB, W, V, P6, N Bumpers are standard stroke for each " of stroke /2-20 thd. /4-8 NPT -4 thd. both ends Dual Double Stacked Cylinder Press Furnished without nut(s). See Chart on Page 50. Custom Double Stacked Stainless Steel Cylinder 202 High Flow Booster Valve JFC-2A Flow Control Super Structure Clippard Modular Valves CMO-23 Two-Hand No Tie Down Clippard Polyurethane Hose MAV-3 3-Way Control Valve Press Fixture Clippard Instrument Laboratory, Inc

49 3/4 BORE ACCESSORIES MOUNTING NUTS Stud Nut Part Across Nut Nut Number Flats Thickness (Thread) N6-4 /2 35/64-4 Rod Nut Part Across Nut Nut Number Flats Thickness (Thread) N07-20 /6 /4 7/6-20 CB-2495 Clevis Bracket RK-2899 Replaceable Rod Seal Material: aluminum body Two holes 0.87 deep for spanner.297 Inserted pre-lube bronze oilite bearing V-Section seal O-Ring RC Rod Clevis sq thru both sides Anodized Finish RE thd. Lubricate seal and O-Ring before replacing Rod End body Bronze Bearing /2-20 thd. FB-289 Foot Bracket Body typ..500 dia /2-20 Body Flats.03 thru Lockwasher Locknut Max. Static Radial Load: 6700 lbs. Fits Rod Thread Size: / Clippard Instrument Laboratory, Inc

50 2 BORE STAINLESS STEEL CYLINDER SSR Options: MB, B, V, S, N Standard Stroke Lengths:, 2, 3, 4, 5, 6, 7, 8, 0, 2 Spring Compressed: 30 lbs. Spring At Rest: 5 lbs for each " of stroke For S option add /4-2 thd. /2-20 thd. /4-8 NPT USR Mount: Universal Options: MB, B, V, N Spring Compressed: 30 lbs. Spring At Rest: 5 lbs for each " of stroke SDR UDR Options: C, F, R, MB, B, W, V, P6, P7, P8, S, N /4-8 NPT /4-2 thd. both ends /2-20 thd., 5, 6 For S option add.375 /2-20 thd. /4-2 thd Furnished without nut(s). See Chart on Page 54. For C, F, R and S options add stroke /4-8 NPT both ports Mount: Universal 5, 6, 7, 8, 0, 2 Options: C, F, R, MB, B, W, V, P2, P3, P4, P5, P6, P7, P8, N stroke For C, F, & R options use side ported rear head /4-8 NPT both ports /4-2 thd. both ends /2-20 thd Clippard Instrument Laboratory, Inc Furnished without nut(s). See Chart on Page 54. 5

51 2 BORE STAINLESS STEEL CYLINDER SDD Standard Stroke Lengths:, 2, 3, 4, 5, 6, 8, 0, 2 Type: Double Rod Options: C, F, MB, B, W, V, P2, P3, P4, P5, P6, P7, P8, N stroke (2 x stroke) stroke SRR Reverse Acting /4-8 NPT both ports /4-2 thd. both ends /2-20 thd. both ends Nuts included, but not shown on drawing Standard Stroke Lengths:, 2, 3, 4, 5, 6 Spring Compressed: 30 lbs. Spring At Rest: 5 lbs. Options: MB, B, W, V, N stroke for each " of stroke /2-20 thd. /4-8 NPT /4-2 thd. URR Reverse Acting stroke 0.25 Mount: Universal Spring Compressed: 30 lbs. Spring At Rest: 5 lbs. Options: MB, B, W, V, P6, N for each " of stroke /2-20 thd. /4-8 NPT /4-2 thd. both ends SFR Spring Bias Spring Compressed: 30 lbs. Spring At Rest: 5 lbs. Options: MB, B, W, V, P6, P7, P8, S, N For S option add Furnished without nut(s). See Chart on Page for each " of stroke /4-8 NPT both ports /4-2 thd. /2-20 thd. 52 Clippard Instrument Laboratory, Inc

52 2 BORE STAINLESS STEEL CYLINDER SBR Spring Bias Spring Compressed: 30 lbs. Spring At Rest: 5 lbs. Options: MB, B, W, V, P6, P7, P8, S, N For S option add stroke for each " of stroke UFR Spring Bias.2-20 thd..250 /4-2 thd. /4-8 NPT both ports Mount: Universal Spring Compressed: 30 lbs. Spring At Rest: 5 lbs. Options: MB, B, W, V, P2, P3, P4, P5, P6, P7, P8, N for each " of stroke /4-8 NPT both ports /2-20 thd. /4-2 thd. both ends UBR Spring Bias Mount: Universal Spring Compressed: 30 lbs. Spring At Rest: 5 lbs. Options: MB, B, W, V, P2, P3, P4, P5, P6, P7, P8, N stroke 0.25 Furnished without nut(s). See Chart on Page for each " of stroke /2-20 thd. /4-8 NPT both ports /4-2 thd. both ends Furnished without nut(s). See Chart on Page 54. Did you know... All Clippard Cylinders are 00% tested. Clippard Instrument Laboratory, Inc

53 2 BORE ACCESSORIES MOUNTING NUTS Stud Nut Part Across Nut Nut Number Flats Thickness (Thread) N20-2 3/4 7/6 /4-2 Rod Nut Part Across Nut Nut Number Flats Thickness (Thread) N /4 5/6 /2-20 CB-3295 Clevis Bracket RK-3299 Replaceable Rod Seal Material: aluminum body Two 0.56 holes deep for spanner.32 Inserted pre-lube bronze oilite bearing.750 V-Section seal O-Ring RC Rod Clevis sq. - thru both sides Anodized Finish RE /4-2 thd. Lubricate seal and O-Ring before replacing Rod End body Bronze Bearing.687 /2-20 thd. FB-329 Foot Bracket rad. Body.25 dia /2-20 Body Flats Lockwasher Locknut Max. Static Radial Load: 6700 lbs. Fits Rod Thread Size: / Clippard Instrument Laboratory, Inc

54 2 /2 BORE STAINLESS STEEL CYLINDER SDR Options: C, F, R, MB, W, V, P6, P7, P8, S, N Standard Stroke Lengths:, 2, 3, 4, 5, Bumpers are standard stroke For S option add UDR /2-20 thd /4-8 NPT both ports 3/8-2 thd stroke For C, F, & R options use side ported rear head Mount: Universal Standard Stroke Lengths:, 2, 3, 4, 5, 6, 7, 8, 0, 2 Options: C, F, R, MB, W, V, P2, P3, P4, P5, P6, P7, P8, N Bumpers are standard SDD /2-20 thd stroke /4-8 NPT both ports 3/8-2 thd. both ends Furnished without nut(s). See Chart on Page 56. Standard Stroke Lengths:, 2, 3, 4, 5, 6, 8, 0, 2 Type: Double Rod Options: C, F, R, MB, W, V, P6, P7, P8, N Bumpers are standard (2 x stroke) stroke /4-8 NPT both ports 3/8-2 thd. both ends /2-20 thd. both ends Clippard Instrument Laboratory, Inc

55 2 /2 BORE ACCESSORIES MOUNTING NUTS Stud Nut Part Across Nut Nut Number Flats Thickness (Thread) N22-2 7/8 /2 3/8-2 Rod Nut Part Across Nut Nut Number Flats Thickness (Thread) N /4 5/6 /2-20 CB-3295 Clevis Bracket RK-4099 Replaceable Rod Seal Material: aluminum body Two 0.56 holes deep for spanner.375 Inserted pre-lube bronze oilite bearing V-Section seal O-Ring RC Rod Clevis sq thru both sides Anodized Finish RE /8-2 thd. Lubricate seal and O-Ring before replacing Rod End body Bronze Bearing /2-20 thd. FB-409 Foot Bracket rad. Body.437 dia /2-20 Body Flats Lockwasher Locknut Max. Static Radial Load: 6700 lbs. Fits Rod Thread Size: / Clippard Instrument Laboratory, Inc

56 3 BORE STAINLESS STEEL CYLINDER SDR Options: MB, W, V, P6, P7, P8, S, N Standard Stroke Lengths:, 2, 3, 4, 5, stroke 0.33 Bumpers are standard No additional length for bumpers For S option add /8-8 thd. /2-2 thd. 3/8-8 NPT both ports UDR Mount: Universal Standard Stroke Lengths:, 2, 3, 4, 5, 6, 7, 8, 0, 2 Bumpers are standard Options: MB, W, V, P2, P3, P4, P5, P6, P7, P8, N No additional length for bumpers stroke /8-8 thd. /2-2 thd. both ends 3/8-8 NPT both ports SDD Type: Double Rod Options: MB, W, V, P6, P7, P8, N Standard Stroke Lengths:, 2, 3, 4, 5, 6, 8, 0, stroke.250 Furnished without nut(s). See Chart on Page (2 x stroke) stroke Bumpers are standard No additional length for bumpers /8-8 NPT both ports /2-2 thd. both ends 5/8-8 thd. both ends Nuts included, but not shown on drawing Did you know... Minimatic Minimetric Fluidamp Octoport Air-2-Electric and Air Force One are all Clippard s registered trademarks. Clippard Instrument Laboratory, Inc

57 3 BORE ACCESSORIES MOUNTING NUTS Stud Nut Part Across Nut Nut Number Flats Thickness (Thread) N /4 /2 /2-2 Rod Nut Part Across Nut Nut Number Flats Thickness (Thread) N /4 5/6 /2-20 CB-4895 Clevis Bracket RK-4899 Replaceable Rod Seal Material: aluminum body Two 0.56 holes deep for spanner.625 Inserted pre-lube bronze oilite bearing V-Section seal O-Ring RC-488 Rod Clevis Anodized Finish /2-2 thd. Lubricate seal and O-Ring before replacing thru both sides sq RE-4885 Rod End body Bronze Bearing 5/8-8 thd. FB-489 Foot Bracket typ Body dia 5/8-8 Body Flats Lockwasher Locknut Max. Static Radial Load: 7400 lbs. Fits Rod Thread Size: 5/ Clippard Instrument Laboratory, Inc

58 POSITION SENSORS HS-990 Hall Effect Sensors mounting strap.05 Output type Input voltage (Vin) Operation temp. Input current (Iin) Output voltage drop Output current (Iout) Power dissipation Lead Wire Circuit protection Sinking (open collector output) 5 to 28 VDC 0 to 85 F 25 ma maximum.4 VDC maximum Iout =.3 Vin, 300 ma maximum 300 mw maximum 22 ga. x 4 ft. also avail. in 2 ft. length HS Reverse polarity protected, transient voltage protected and false pulse protected approximate sensing point 0.35 L.E.D. wire lead 0.40 Hall Effect Wiring Diagram (-) Black White Load (+) Red HS-990 Magnetic Reed Switch RS-0L RS-05L RS-2500 Circuit Diagram mounting strap RSwire lead RS-05L pictured approximate sensing point Universal Clamps L.E.D SC-08 SC-0 SC-2 SC-4 SC-7 SC-20 SC-24 SC-28 SC-32 SC-40 SC48 Clippard s stainless steel clamps are designed to be used with the Hall Effect and the reed switch. All clamps should be ordered based upon the size of the cylinder on which it will be mounted. The part numbers show the bore size using the numerical code. Each clamp is wide stainless steel, and is equipped with a locking screw with #5-40 threads. Clippard Instrument Laboratory, Inc

59 AIR VOLUME TANKS AVT- - AVT-2- AVT-7-2 AVT-7-3 AVT-24-4 AVT-24-6 AVT-24-8 AVT-24-0 AVT-32-2 AVT-32-4 AVT-32-6 Additional models are available upon request Clippard offers a line of air volume tanks suitable for use with Clippard air components. Using the same quality rolled construction as Clippard stainless steel cylinders, tanks are manufactured to exacting standards. Each is provided with a threaded port at both ends. See chart for volume capacity, dimensions, and port information. For additional corrosion resistance Clippard can offer air volume tanks with Delrin heads. Call for more information. A D D B C E FEATURES Volumes from to 6 cu. in. Ten models 304 stainless steel tubes Precision rolled construction Easy to connect, mount and use in your circuits Anodized aluminum heads Maximum pressure 250 psig Part Number AVT-2- AVT-7-2 AVT-7-3 AVT-24-4 AVT-24-6 AVT-24-8 AVT-24-0 Volume Cubic In A B C D E /8 27 /8 27 /8 27 /8 27 /8 27 /8 27 /8 27 AVT-32-2 AVT-32-4 AVT /4 8 /4 8 / Clippard Instrument Laboratory, Inc