Technical Data... 3 How to Order... 4 Dimensions... 5 Inline Mount Valve... 6 Manifold Dimensions and Part Numbers... 6

Transcription

1

2 Table of Contents Minature Valve Series RB Series Technical Data How to Order Dimensions... 5 Inline Mount Valve Manifold Dimensions and Part Numbers... 6 S Series Technical Data How to Order Dimensions... 8 Manifold Dimensions and Part Numbers... 9 TM Series Technical Data Electrical Circuit Layout How to Order Dimensions Manifold Dimensions and Part Numbers... 1 Blanking Station... 1 S Series Standard Circuit Boards Valve Added and Custom Assemblies Numatics 009 Rev. /06

3 RB Series 3-way Normally closed 1 3 -way Normally closed 1 Valve porting 3-way Normally open 3 RB Series Miniature Valve Tested in excess of 500 Million cycles Maximum leakage rate: 0.3 SCCM (Bubble Tight) Temperature range: -10 F to 150 F (-3 C to 66 C) Class A Insulated coils All valves 100% factory tested #6 AWG Teflon insulated lead wires Circuit board mountable Built in barbed fittings 10 m (Micron) filtration recommended Response time < Seconds All valves rated to 8" Hg. Vac Oxygen Clean available Recommended for use with dry air, lubricated air, vacuum, non-corrosive, non-toxic, non-flammable dry gases. Consult factory for other service applications. Technical Data *Flow (SLPM) (.68) (1.4) (.0) (.7) (4.1) (4.8) (5.4) (6.1) (6.8) Pressure (BAR) PSIG.080 orifices are not available in.080 barbed body styles. *FLOW: (SLPM) Standard liters per minute Port 1- (normally closed) Note: Flow test are based on average readings and nominal components. All outlets are vented to atmosphere. Results may vary. VALVE MAXIMUM PRESSURE SERIES WATTAGE ORIFICE CV BRASS PLASTIC RB 0.5 Watt (0.75) psi 15 psi (1.0) RB 0.5 Watt (1.0) psi 10 psi (0.68) RB 0.5 Watt (1.5) psi (1.7) 10 psi (0.68) RB 1.0 Watt (0.75) psi (6.8) 50 psi RB 1.0 Watt (1.0) psi 50 psi RB 1.0 Watt (1.5) psi 35 psi (.4) RB.0 Watt (0.75) psi (6.8) 100 psi (6.8) RB.0 Watt (1.0) psi (6.8) 70 psi (4.8) RB.0 Watt (1.5) psi (6.8) 70 psi (4.8) RB.0 Watt (1.5) psi 50 psi RB.0 Watt (.0) psi (1.7) 5 psi (1.7) For other pressure ranges and orifice sizes please contact factory Numbers in parentheses ( ) equivalent to Millimeters or BAR where applicable. 3

4 RB Series How to Order R H B 0 6 H 3 0 B Series R = RB Series Power L = 0.5 Watt M=1 Watt H = Watt Body Style M = 10-3 Brass Manifold Mount L = Brass Line Mount B = 0.15 Barb F = Face Seal Mount Configuration = Way 3 = 3 Way Port No. 3 Connection 0 = Way only S = Barb (3 Way only) B = 0.15 Barb (3 Way only) F = 10-3 Female (3 Way only) Seal Material B =Buna (Std.) V =Viton O=Oxygen Cleaned (Viton) Port No. 3 0 = Way Only 4 = (1.0) 5 = (1.5) Port No. 1 3 = (.75) 4 = (1.0) 5 = (1.5) 6 = (1.5) 8 = (.0) Electrical Connection H = Hard Wire (1"/6 AWG) P = PCB Pins (Printed Circuit Board) Voltage 4 = 5 VDC 6 = 1 VDC 7 = 4 VDC Consult chart (page 7) for allowable combinations of wattage, orifice sizes, and pressure range. 4

5 Dimensions.60 (15.4) RB Series Face Seal RB Valve Dimensions.76 (19.30).55 (13.34).774 (19.66) 1.74 (44.0) Option F.795 (0.09).01 (51.05).60 (15.4) Body Ported RB with Mounting Holes 1 INCH LEADWIRE.95 (4.13).76 (19.30) 1.74 (44.0).01 (51.05) Option B RB Manifold Mount Valve 1.67 (4.4).75 (19.04).76 (19.30) 1/8" Barb or 10-3 Female Port (35.56) 10-3 UNF Thread Port 1 Port Option M Manifold Dimensions / Part Numbers (Manifold Mount) See S Series Section Numbers in parentheses ( ) equivalent to Millimeters or BAR where applicable. 5

6 RB Series Inline Mount Valve #6-3 UNC x.19 deep () Mounting Holes 1 Inch Leadwire.69 #10-3 UNF (17.5) Ports 1 &.76 (19.30) Ø.75 (19.05) 1.6 (41.14) 1.89 (48.00) Option L Manifold Dimensions and Part Numbers (Face Seal Mount).500 (1.70).630 REPEATED PER STATION (16.00) Ø.343 THRU 1/8-7 NPTF THD. BOTH ENDS Ø.437 X 90 BOTH ENDS SUPPLY PORTS BOTH ENDS.75 (6.99).75 (6.99) X.65 (15.88).780 (19.81).50 (6.35).388 (9.86) SEE DETAIL Y.156 (3.96) X PER STATION Ø.089 X.300 #4-40 UNF-B X.50 FULL THD () MTG HOLES B A.31 (7.9).47 (6.7).57 (13.39) X PER STATION Ø.100 X Ø.47 X.050 DETAIL Y REPEATED PER STATION SCALE Ø X.65 # 10-3 UNF-3B X.00 REPEA OUTLET PORTS.400 (10.16).800 (0.3) X #9 DRILL (Ø.136) X.50 #8-3 UNF-B X.187 MIN FULL THD. () MTG HOLES MIN FULL THD TED PER STATION PART NO # OF STATIONS A 1.00 (5.4) 1.63 (41.4).89 (73.4) 4.15 (105.4) 5.41 (137.4) 6.67 (169.4) 7.93 (01.4) B 0.50 (1.7) 1.13 (8.7).39 (60.7) 3.65 (9.7) 4.91 (14.7) 6.17 (156.7) 7.43 (188.7) Numbers in parentheses ( ) equivalent to Millimeters or BAR where applicable. 6

7 S Series -way Normally closed 3-way Normally open 3-way Normally closed S Series Miniature Stainless Steel Valve Tested in excess of 500 Million cycles Maximum leakage rate: 0.3 SCCM (Bubble Tight) Temperature range: -10 F to 150 F (-3 C to 66 C) Class A Insulated coils All valves 100% factory tested #0 AWG & #4 AWG Teflon insulated lead wires Tin plated brass.110 x.00 Fast-on terminals 10 m (Micron) filtration recommended Response time <.010 Seconds All valves rated to 8" Hg. Vac Oxygen Clean available Recommended for use with dry air, lubricated air, vacuum, non-corrosive, non-toxic, non-flammable dry gases. Technical Data *Flow (SLPM) Orifices are Inch/Diameter Consult factory for other service applications (.68) (1.4) (.0) (.7) (4.1) (4.8) (5.4) (6.1) (6.8) Pressure PSIG (Bar) *Flow (SLPM) Standard liters per minute port 1 >. (Normally closed) NOTE: Flow tests are based on average readings and nominal components. All Outlets are vented to atmosphere. Results may vary. VALVE SERIES LS WATTAGE 0.65 watt ORIFICE (0.75) CV 0.05 MAXIMUM PRESSURE N.C. N.O. 100 PSI (6.8) 50 PSI 1.5 watt (0.75) PSI (6.8) 100 PSI (6.8) 1.5 watt (1.00) PSI (6.8) 50 PSI HS 1.5 watt 1.5 watt (1.5) (1.50) PSI 50 PSI (6.8) 50 PSI 50 PSI 1.5 watt (1.80) PSI 50 PSI 1.5 watt (.00) PSI 40 PSI Numbers in parentheses ( ) equivalent to Millimeters or BAR where applicable. 7

8 S Series How to Order H S 0 3 M 7 H 0 0 B Power H =High Power Coil 1.5 W L =Low Power Coil 0.65 W Service S = Standard valve O = Oxygen Cleaned F = Food Grade* Port Threads O = Standard l0-3 Stud M = Metric M5 Stud N = 1/8" NPT (mounting option C ) Configuration = Way Valve 3 = 3 Way Valve Mounting L = Line Mounted M = Manifold Mounted (10-3 stud only) C = Cylinder Mounted (10-3, orifice only) Seal Material B = Buna-N (Std.) V = Viton E = EPR N = Neoprene Port No. 3 0 = 0.40 (1.00) Std. 1 = 0.50 (1.5) Port No. 1 0 = (0.75) Std. 1 = (1.00) = (1.5) 3 = (1.50) 4 = (1.80) 5 = (.00) Connectors H = Hardwire (1"/ 0 AWG) F = Faston S = Hardwire (1" / 4 AWG). Dimensions Voltages 1 = 10 VAC 50/60 Hz = 30 VAC 50/60 Hz (Rectified Only) 3 = 4 VAC 50/60 Hz 4 = 5 VDC 5 = 6 VDC 6 = 1 VDC 7 = 4 VDC 3-Way Consult chart (page 7) for allowable combinations of wattage orifice size, and pressure range. * Note: Food Grade Valves Must be manifold mount w/epr seals only! -Way Numbers in parentheses ( ) equivalent to Millimeters or BAR where applicable. 8

9 S Series Manifold Dimensions and Part Numbers (Manifold Mount) PART NUMBER NO. OF STATIONS A B N/A N/A N/A (60.33) (1.46) (80.16) 1.65 (41.8) (99.99).406 (61.11) (119.84) (80.95).375 (9.53) SINGLE STATION MANIFOLD No /8 NPTF Supply Port 1/8 NPTF Output Port -STATION MANIFOLD No (0.6).406 (10.31) No UNF -3B Outlet Ports.375 (9.53).75 (19.05) Sq 8-3 x.0 Deep () Mtg. Holes 10-3 x.37 Deep Valve Mtg. Hole (Opposite Side).375 (9.53) (10.90) (17.5) 1.17 (9.7).187 (4.75).585 (14.86) 1/16 Dia. x.30 Deep (Opposite Side).19 (5.56).438 (11.13) 4-STATION MANIFOLD No (4.75) 1/8 NPTF Supply Ports Both Ends.875 (.3).406 (10.31).19 (5.56).375 (9.53).800 (0.3).400 (10.16).438 (11.13) 8 3 x.187 Deep () Mtg. Holes MULTI-STATION MANIFOLD Numbers in parentheses ( ) equivalent to Millimeters or BAR where applicable. 9

10 TM Series 3-way Normally closed Valve porting 3-way Normally open TM Ten Millimeter Miniature Valve Tested in excess of 00 Million cycles Maximum leakage rate: 0.3 SCCM (Bubble Tight) Epoxy Impregnated, Nylon Encapsulated Class F continuous duty (ED 100%) All valves 100% factory tested Circuit board mountable All valves rated to 8" Hg. Vac Oxygen Clean available Female locking connector or hardwire leads available Technical Data Flow Capacity: Standard Cv Quick Exhaust Cv Operating Pressure: Vacuum to 100 PSIG (6.9 Bar) Operating Temperature: 3 F to 10 F (-5 C to 50 C) Fluid Temperature: 3 F to 10 F (0 C to 50 C) Voltage: 1 and 4 VDC Power: 1. Watt (1.35-Watt w/led) Response Time: <.010 Seconds Filtration: 10 m (Micron) recommended Wire Gauge: #4 AWG Teflon Insulated lead wires Seal Material: Viton Service: Recommended for use with dry air, lubricated air, vacuum, non-corrosive, nontoxic, non-flammable dry gases. Consult factory for other service applications. Electrical Circuit Layout Hardwire Circuit Board Mountable Coils up & out Coils 1 & 4 VDC 1 & 4 VDC 10

11 TM Series How to Order TM 101 V 1 C Series TM = TM Series (10mm) Configuration 101 = Normally Closed 10 = Quick Exhaust N.C. 11 = Normally Open Seal Material V = Viton (Std.) Coil and Connection Type 1 = Hard Wire w/ 1" Lead = UP Connector w/ Diode and LED 3 = OUT Connector w/ Diode and LED 4 = Circuit Board Mountable Power C = 1. Watts (1.35 Watts w/ LED) L =0.75 Watts (Hardwire and CB Mount only) Voltage 1 = 1 VDC 4 = 4 VDC Dimensions Straight/Out Coil with Normally Closed Valve Right Angle/Up Coil.77 (19.56). (5.59) 1.06 (6.9).48 (1.19).87 (.10) MANUAL OVERRIDE BUTTON.48 (1.19).40 (10.16) 1.06 (6.9) Hardwire Coil with Quick Exhaust Valve Circuit Board Mountable Coil 1.06 (6.9).65 (16.51) NORMAL MANUAL OVERRIDE BUTTON X M 1.7 X.35 MOUNTING SCREWS 1.06 (6.9) EXHAUST IS VENTED OUT SIDES.0 PIN SPACING.165 (4.19) 11

12 TM Series Manifold Dimensions and Part Numbers 3X Ø.047 MAX. MI. 7 THREAD.847 (1.51).067 (1.70) (.59).096 (.44).6 X Ø.140 B.10 X MI.7 X.35 X.118" MIN UNF 10-3 UNF 10-3 UNF.984 (4.99).560 (14.) A.413 (10.49).197 (5.00) (10.01).197 (5.00) Manifold Sub Base Overall Dimensions Numatics Miniature Pneumatic Group will assemble valves on manifolds upon request. To specify, add ASM to the end of the manifold part number. Valves are specified separately. For example: A 4 station assembly Part# Qty ASM 1 TM101V1C1 4 PART NO. # OF STATIONS A B (3.1) 1.3 (33.5).15 (54.6).97 (75.4).97 (75.4) 4.63 (117.6) 5.45 (138.4) 0.67 (17.0) 1.08 (7.4) 1.91 (48.5).74 (69.6).74 (69.6) 4.39 (111.5) 5. (13.6) Blanking Station Mating Connector Assembly for out and up coils. *Part Number TM10- XX Part # TM10-1 TM10-4 TM10-40 Wire Length 1" (300mm) 4" (600mm) 40" (1000mm) 1

13 S Series Standard - Circuit Boards Circuit Boards - S Series Standard All stainless steel construction High Flow - Cv double the flow of similar valves Wide pressure ranges 8" Hg. Vacuum PSIG Unmatched Repeatability Multi-fluid compatibility Low power draw 0.65 W D.C. Cool running Fast response time - 5ms Durable, Effective, Reliable Model Selection Chart 4 VDC 1 VDC = 1 Station Card = 1 Station Card XX XX Part # # Stations Part # # Stations *Standard S Valve cards utilize LS03MXH00B with electrical connector. 13

14 Value-Added Custom Assemblies Specialize in Value Added and Custom Built Assemblies Numatics MPG continues to be Everywhere you need us to be when it comes to OEM custom and Value Added assemblies. Our commitment towards total product management allows for one on one engineering, innovative design and cost-effective manufacturable products to be provided to our customers. This unique approach encourages close customer/supplier interaction, dramatically reducing the lead-times associated with the process of taking concepts to production. We re everywhere you need us to be Custom Engineering of manifold assemblies Serial interfacing Custom wire harness assemblies Rapid prototype turnaround State of the art testing capabilities Pioneered in the area of specifically designed plastic valve components Special valve performance capabilities Application specific valve designs Custom labeling Custom Circuit boards 14

15 WORLD HEADQUARTERS USA Numatics, Incorporated 4680 Dylan Drive Novi, Michigan P: Numatics Canada Numatics, Ltd P: Mexico Numatics de Mexico S.A. de C.V. P: For a comprehensive listing of all Numatics production and distribution facilities worldwide, visit: Numatics Inc. 008 LT-G3Catalog M-TGI-1/08