#908C. Weatherly Index #148. For Transportation and Industry Lifting / Cargo Control / Hardware / Winter Traction Products

Transcription

1 #0C Weatherly Index #4 For Transportation and Industry Lifting / Cargo Control / Hardware / Winter Traction Products

2 General Warnings & Information for SCC Products WARNING: The products in this catalog are not designed for overhead lifting applications or vehicle towing except where noted as approved. Only approved G0/S alloy chain & fittings and approved lifting slings comply with O.S.H.A. regulations for lifting applications (shown on pages ~2). Straps, chains, component parts and attachments in this catalog are for general utility use only (unless otherwise stated on each page). These products should never be used in a manner where strap, chain or attachment failure could cause property damage, serious personal injury or loss of life. Read and understand all product warnings/cautions and instructions prior to using. USE OF THESE PRODUCTS DEMONSTRATES AN UNDERSTANDING OF THESE WARNINGS AND THE RISKS INVOLVED. SAFE USE: Any of the following abuses of product will result in greatly reduced load capacity and may result in serious personal injury or loss of life: ) Twisting of the strap/chain assembly, knots or kinks in the strap/chain assembly, tip loading of hooks. 2) Deterioration of the strap/chain assembly or attachments by wear, usage, abuse, corrosion, or exposure to UV and/or chemicals. 3) Impacts caused by jerking or snatching. This type of impact puts extreme stress on the product and could cause premature failure. 4) Use for any purpose other than that for which the product was designed and intended to be used. INSTRUCTIONS FOR ATTACHMENTS: When attachments such as hooks, shackles or other items are used with chain or strap assemblies, maximum care should be used to select the attachment of the same type, size, grade and working load limit as that of the chain/strap assembly. DEFINITIONS: MINIMUM BREAKING STRENGTH (MBS) or ASSEMBLY BREAK STRENGTH: The minimum force in pounds or kilograms at which the chain, strap assembly, fittings or related items, in the condition it leaves the producers plant, has been found by representative testing to break when a constantly increasing force was applied in direct tension to a straight length of chain, strap, fittings or related items on a standard testing machine. Breaking force values are a statistical attribute test and are not a guarantee that all chain/strap segments will endure these loads. Breaking force loads shall not be used as a criteria for service or design. WORKING LOAD LIMIT (WLL): The maximum combined static and dynamic load in pounds or kilograms that shall be applied in direct tension to an undamaged straight length of chain, strap, fitting or related item. PROOF TESTING: A quality control tensile test applied to chain, strap, fitting or related item for the purpose of verifying weld integrity, sewing pattern strength and material quality. It is the minimum force in pounds or kilograms which the chain or strap has withstood at the time it left the producers plant, under a test in which a constantly increasing force has been applied in direct tension to a straight length of chain or strap. Proof test loads are a manufacturing integrity test and shall not be used as criteria for service or design. DESIGN FACTOR: The ratio of the Minimum Breaking Strength (MBS) to the working load limit (WLL) assigned to each product during design, development and initial product testing. If an item states a 4: design factor, that means it will withstand stress equal to or in excess of 4 times the working load limit. TRADE SIZE: The common reference size used to identify chain and component parts. Actual size may differ from trade size. SPECIFICATION TOLERANCE: +5% to 3%. SHOULD: This word is used in warnings and informational statements to denote an action or procedure that is STRONGLY RECOMMENDED. SHALL: This word is used in warnings and informational statements to denote an action or procedure that is REQUIRED. COLOR KEY TO SCC WARNING, CAUTION & INFORMATION STATEMENTS: DANGER OR WARNING (RED): This symbol & color denotes a potentially dangerous situation or an extremely important warning. It is used whenever the great likelihood exists for property damage, serious personal injury and/or loss of life if the warning is not heeded, or of a known violation of the law. WARNING (ORANGE): This symbol & color denotes moderately important warnings. It is used whenever the probability exists for property damage, serious personal injury and/or loss of life if the warning is not heeded. CAUTION OR WARNING (YELLOW): This symbol & color denotes a caution or warning. It is used whenever the possibility exists for property damage, serious personal injury and/or loss of life if the caution or warning is not heeded. NOTE (BLUE): This symbol and color denotes a general information statement. There is no danger of personal injury or property damage. 2 Approved NOT Approved

3 COMPARATIVE TABLE OF WIRE & CHAIN SIZES: Washburn and Moen Gauge No. 20 No. No. 7 No. 6 No. 5 No. 4 No. 3 No. No. No. No. No. No. 7 No. 6 No. 5 No. 4 Nearest Fraction of an inch /32 3/64 3/64 + /6 5/64 5/64 + 3/32 7/64 / /64 5/32 5/32 5/32 + /64 3/6 3/6 + 3/64 5/64 /4 /4 /32 /32 5/6 5/6 + /32 / /32 7/6 + 7/6 5/32 /2 + Decimals of an inch Equivalent in mm CHAIN NUMBER WELDLESS WELDED Double Loop Coil Machine No. 7 No. 6 No. 5 No. 4 No. 3 No. 2 No. /0 2/0 3/0 4/0 5/0 6/0 7/0 /0 No. 4 No. 3 No. 2 No. /0 2/0 3/0 4/0 5/0 6/0 7/0 /0 /0 /0 /0 No. 4 No. 3 No. 2 No. /0 2/0 3/0 4/0 5/0 6/0 7/0 /0 /0 /0 /0 General Index Section Lifting Products Section 2 Cargo Control Section 3 Industrial Chain, Cable & Accessories Section 4 Winter Traction Products Cable Chain...03 Section 5 Winter Traction Products Link Chain NONTRACTION PRODUCT WARRANTY: The nontraction items in this catalog are warranted to be free from defects in workmanship and materials for one year from date of purchase by user. No other warranty, expressed or implied, including the implied warranty of merchantability or fitness for a particular use, is given and no affirmation, by words or actions shall constitute a warranty. Defective product may be returned to place of purchase or returned to the manufacturer, freight prepaid within days of discovery of alleged defect. Inspection will be made to determine the cause of failure or defect. Product determined to be defective will be repaired or replaced at the discretion of the manufacturer. No compensation will be made for any labor claim, delays or damages incurred by using this product. Although this warranty gives you specific rights, you may have other legal rights that differ from state to state. For more information, please contact SCC at the address below. WINTER TRACTION PRODUCT WARRANTY: All SCC winter traction products are warranted free from defect in workmanship and material for one year from the date of delivery to user. Defective product may be returned to the manufacturer, freight prepaid, within days of discovery of alleged defect. Inspection will be made to determine cause of failure. Chain determined to be defective will be repaired or replaced. Buyer shall not be entitled to recover any incidental or consequential damages. No compensation will be made for any labor claim, delays or damages incurred by using this product. Although this warranty gives you specific rights, you may have other legal rights which differ from state to state. For more information contact SCC at the address below. SPEEDS OVER 30MPH / 50KmH, IMPROPER FIT OR IMPROPER INSTALLATION VOID THIS WARRANTY CAUTION: All winter traction product crossmembers will wear out with extended use. Products can also break due to misfit, misapplication or misuse. If this should occur, stop immediately and repair or replace product. If these cautions are ignored, SCC and its distributors are not responsible for injury or vehicle damage. Manufacturer will not warranty alloy wheels or wheel covers damaged by chains or chain tighteners. SCC WARRANTY & CUSTOMER SERVICE INFORMATION: SCC, Customer Service Dept. P.O. Box 4 Clackamas, OR U.S.A Section 5 Winter Traction Product Spare Parts Section 6 Traction Product Retail Displays & Point of Purchase Material... 5 Link Chain Specifications Traction Product Packaging Specifications Product Index

4

5 Section Lifting Products Nylon Sling Information Nylon Lifting Slings... Grade 0 Alloy Information... Grade 0 Alloy Chain... Grade 0 Alloy Accessories... 2 Chain Sling Tag... Master Link... 3 Omega Connecting Link... 3 SelfLocking Hooks... 4 Connecting Link... 5 Web/Sling Connecting Link 5 Excavator Hook... 5 Eye Shortening Hook... 5 Twist Eye Choke Hook... 6 Clevis Sling Hook... 6 Eye Sling Hook... 6 Clevis Claw Hook... 6 Grab Hooks... 7 S.P.A. Shackle... 7 Clutch Sling Hook... WeldOn Anchor Point... BoltOn Anchor Point... Parts for Hooks... Insulated Swivel Coupling Attachments

6 LIFTING PRODUCTS Nylon Sling Warnings & Info SAFE USE: Nylon Lifting Slings DANGER: Overhead lifting presents a very real danger of serious personal injury or loss of life if lifting equipment is not used properly. O.S.H.A. and ASME have adopted the following requirements for safe operation of all lifting slings. Please read and understand all of these instructions prior to using any lifting sling or sling assembly. Slings should only be used by qualified persons who are responsible for the sling & rigging selection, inspection and use. USE OF THESE PRODUCTS DEMONSTRATES AN UNDERSTANDING OF THESE WARNINGS AND THE RISKS INVOLVED. Inspect all sling components prior to each use. Never use slings that are damaged or defective. Damaged or defective slings must be removed from service immediately. The following conditions constitute a damaged sling: acid or caustic burns, melting of any part of the web surface, broken or worn stitching, distortion of eyes or fittings, or web snags, cuts, tears, and punctures. Only slings with legible identification tags shall be used. Keep all tags and labels away from the load, hook and point of choke, to avoid rendering the tag nonreadable and the sling therefore unusable. If in doubt about the safety of a sling, DO NOT use it without having it proof tested. Slings must never be shortened with knots, sewing or other makeshift devices nor should they ever be extended from their original length with nonoriginal hardware, fittings or other devices. Never twist or kink the legs of a sling. The web sling legs (branches) shall contain or support the load from the sides above the center of gravity when using a sling in a basket configuration. Web slings shall not be bunched between the ears of a clevis, shackle or in a hook. Never load in excess of the rated capacity for the application. Consideration must be given to the load angle (see Sling Angle Chart on page 7) which affects the rated capacity of the sling. Shock loading shall be avoided. The load applied to a hook shall be centered in the base or bowl of the hook to avoid hook tip overloading. Select only web slings with suitable characteristics for the load type, hitch and the environment of their use. Web slings should always be hitched in a manner that provides for control of the load. Web slings used in a basket hitch must have the load balanced to prevent slippage. Web slings used in a choker hitch must be of sufficient length to assure that the choking action is on the webbing, NEVER ON THE FITTINGS, EYES OR SLING I.D.TAG. Never drag web slings on the floor. Protect webbing at all times from corners, edges, protrusions, or abrasive surfaces. Never pull slings out from under a load when the load is resting on the sling. Place blocks under the load prior to setting down the load to allow removal of the web sling. Do not drop web slings with metal end fittings. Personnel must keep all body parts from between the sling and the load, and from between the sling and the crane/hoist hook. Persons shall never ride the web sling or the load during lifting or while suspended. Persons shall stand clear of all loads while lifting or while suspended. During lifting, with or without the load, personnel must be alert for possible snagging of the load or the web sling. When not in use, web slings should be stored in a cool, dry and dark place to avoid loss of strength through exposure to ultraviolet (UV) light or weather. Never store web slings in areas that are chemically active. Chemicals can destroy the integrity of web slings in varying degrees that are not always readily apparent upon visual inspection. Never store or use web slings in temperatures above 4 F (0 C) or below minus 40 F (40 C). Never attempt to repair a damaged web sling. Replace it immediately. Only Type I and Type II web sling hardware may be reused and then only by a qualified sling manufacturer after inspection. HOW TO ORDER SCC SLINGS: All part numbers shown in our catalog reflect the minimum length that a sling can be manufactured. SCC manufactures nylon slings up to 75 feet in length. To order the correct size and type of sling, please refer to the part number explanation shown below: SEE70203 Each sling part number begins with a BLACK S The 2 RED letters refer to the type or style of sling. The PURPLE number refers to the ply(s) of the sling. SCC offers slings in both ply and 2 ply. Abbr. Description Type Abbr. Description Type TC TT EE Choker Double Triangle Double Flat Eye I II III TW EN RE Double Twisted Eye Endless Reverse Eye IV V VI The ORANGE number refers to the class of sling. SCC slings are all heavyduty class 7 made with 00 lbs/in. premium nylon webbing. The GREEN numbers refer to the width of the sling, preceded by a 0. SCC manufactures slings in widths from inch to 6 inches or 0~06. The BLUE numbers refer to the length of the sling. ( 03 is a 3 foot sling ). Slings are available in lengths from 3 to 75 feet (03~75). 6

7 LIFTING PRODUCTS SLING ANGLE / CAPACITY CHART: Nylon Lifting Slings Rated capacity of choker hitch Angle of Choke Sling rated load factor Nylon Sling Warnings & Info 0 ~ 0 5 ~ 0 0 ~ Sling angles & ratings Angle Horizontal Loss Factor Examples of loss % at angle Base sling=6,300 Lb basket rating INCREASE THE LIFE OF YOUR SLING: To protect sling ends from abrasion due to use on rough surfaces or attachments, SCC recommends you order a choker (STC) or triangle (STT) sling. SCC also offers protective sleeves and buffers. The sleeves can be floating or sewn into a fixed wear position on the sling. Buffers are sewn to the web in a fixed location only. They are available in widths from 6 and lengths up to 60 feet. Protective Sleeves & Buffers When ordering sleeves for 2 ply slings, order the next size larger sleeve to fit over the added thickness of the sling. SLEEVES BUFFERS Width Length (Feet) SLEEVES BUFFERS SCS0 SCS02 SCB0 SCB Each Each Protective Sleeve SCS03 SCB Each SCS04 SCB Each SCS06 SCB Each Protective Buffer Catalog weights are approximate Minimum order quantity: package 7

8 LIFTING PRODUCTS Heavy Duty Class 7 Nylon Lifting Slings Nylon Slings SCC's lifting slings are manufactured from premium nylon sling webbing and include a stamped, heavy leather identification tag sewn securely to each sling. This tag is imprinted with the working load limits for the three sling configurations (vertical, choker, basket) as well as the part number and batch code which includes the date of manufacture. Remember that the law requires a lifting sling to be removed from service if the capacity tag is NOT legible so with this information imprinted, you can realize a longer service life. SCC slings come individually shrinkwrapped to allow them to stack neatly, display attractively and stay clean until sold. Many popular sling sizes are stocked; other sizes are made to order Approved For Overhead Lifting Choker Sling Width x Length PLY 2 PLY (Inches x Feet) Type STC70203 STC x 3 I Working Load Limit (Lbs) VERTICAL CHOKER BASKET PLY 2 PLY PLY 2 PLY PLY 2 PLY PLY 2 PLY ,0 6,200 2,500 5,000 6,200,400 STC70303 STC x 3 I ,700,00 3,00 7,000,400 7,600 STC70403 STC x 3 I ,200,000 5,000,00,400 22,000 STC70603 STC x 3 I ,300 6,500 7,400 3,200,600 33,000 Design factor 5: STC Slings are available in lengths from 3 to 75 feet and widths of 2, 3, 4 & 6 inches. Double Triangle Sling Width x Length PLY 2 PLY (Inches x Feet) Type STT70203 STT x 3 II Working Load Limit (Lbs) VERTICAL CHOKER BASKET PLY 2 PLY PLY 2 PLY PLY 2 PLY PLY 2 PLY ,0 6,200 2,500 5,000 6,200,400 STT70303 STT x 3 II ,700,00 3,00 7,000,400 7,600 STT70403 STT x 3 II ,200,000 5,000,00,400 22,000 STT70603 STT x 3 II ,300 6,500 7,400 3,200,600 33,000 Design factor 5: STT Slings are available in lengths from 3 to 75 feet and widths of 2, 3, 4 & 6 inches. Double Flat Eye Sling Width x Length PLY 2 PLY (Inches x Feet) Type SEE703 SEE2703 x 3 III SEE70203 SEE x 3 III SEE70303 SEE x 3 III SEE70403 SEE x 3 III SEE70603 SEE x 3 III Working Load Limit (Lbs) VERTICAL CHOKER BASKET PLY 2 PLY PLY 2 PLY PLY 2 PLY PLY 2 PLY ,600 3,0,300 2,500 3,200 6, ,0 6,200 2,500 5,000 6,200, ,700,00 3,00 7,000,400 7, ,200,000 5,000,00,400 22, ,300 6,500 7,400 3,200,600 33,000 Design factor 5: SEE Slings are available in lengths from 3 to 75 feet and widths of, 2, 3, 4 & 6 inches. SEE Slings are available in lengths from 3 to 75 feet and widths of, 2, 3, 4 & 6 inches. WARNING: Never exceed Working Load Limit. Failure to follow the lifting sling use, care and inspection instructions could result in property damage, serious personal injury and/or loss of life. Refer to pages 6 & 7 of this catalog for instructions. NOTE: Class 7 slings are designed for overhead lifting and hoisting applications. These products meet all O.S.H.A. and ANSI B30., B30. & B30.26 construction and rating requirements for overhead lifting slings. Minimum order quantity: package Catalog weights are approximate

9 LIFTING PRODUCTS Heavy Duty Class 7 Nylon Lifting Slings SCC's lifting slings are manufactured from premium nylon sling webbing and include a stamped, heavy leather identification tag sewn securely to each sling. This tag is imprinted with the working load limits for the three sling configurations (vertical, choker, basket) as well as the part number and batch code which includes the date of manufacture. Remember that the law requires a lifting sling to be removed from service if the capacity tag is NOT legible so with this information imprinted, you can realize a longer service life. SCC slings come individually shrinkwrapped to allow them to stack neatly, display attractively and stay clean until sold. Many popular sling sizes are stocked; other sizes are made to order Approved For Overhead Lifting Nylon Slings Double Twisted Eye Width x Length PLY 2 PLY (Inches x Feet) Type STW703 STW2703 x 3 IV STW70203 STW x 3 IV STW70303 STW x 3 IV STW70403 STW x 3 IV STW70603 STW x 3 IV Working Load Limit (Lbs) VERTICAL CHOKER BASKET PLY 2 PLY PLY 2 PLY PLY 2 PLY PLY 2 PLY ,600 3,0,300 2,500 3,200 6, ,0 6,200 2,500 5,000 6,200, ,700,00 3,00 7,000,400 7, ,200,000 5,000,00,400 22, ,300 6,500 7,400 3,200,600 33,000 Design factor 5: STW Slings are available in lengths from 3 to 75 feet and widths of, 2, 3, 4 & 6 inches. Endless Sling Width x Length PLY 2 PLY (Inches x Feet) Type SEN703 SEN2703 x 3 V PLY 2 PLY VERTICAL Working Load Limit (Lbs) CHOKER BASKET PLY 2 PLY PLY 2 PLY PLY 2 PLY 3,200 6,200 2,600 5,000 6,400,400 SEN70203 SEN x 3 V ,200,400 5,000,00,400 24,00 SEN70303 SEN x 3 V.0 2.,400 7,600 7,500 4,000,00 35,200 SEN70403 SEN x 3 V ,400 22,000,00 7,600 24,00 44,000 SEN70603 SEN x 3 V ,600 33,000 4,00 26,400 37,200 66,000 Design factor 5: SEN Slings are available in lengths from 3 to 75 feet and widths of, 2, 3, 4 & 6 inches. Reverse Eye Sling Width x Length PLY 2 PLY (Inches x Feet) Type SRE70203 SRE x 3 VI Working Load Limit (Lbs) VERTICAL CHOKER BASKET PLY 2 PLY PLY 2 PLY PLY 2 PLY PLY 2 PLY ,0 6,200 2,500 5,000 6,200,400 SRE70403 SRE x 3 VI ,200,000 5,000,00,400 22,000 SRE70603 SRE x 3 VI ,300 6,500 7,400 3,200,600 33,000 Design factor 5: SRE Slings are available in lengths from 3 to 75 feet and widths of 2, 4 & 6 inches. WARNING: Never exceed Working Load Limit. Failure to follow the lifting sling use, care and inspection instructions could result in property damage, serious personal injury and/or loss of life. Refer to pages 6 & 7 of this catalog for instructions. NOTE: Class 7 slings are designed for overhead lifting and hoisting applications. These products meet all O.S.H.A. and ANSI B30., B30. & B30.26 construction and rating requirements for overhead lifting slings. Catalog weights are approximate Minimum order quantity: package

10 LIFTING PRODUCTS Grade 0 Warnings & Info Grade 0 (S) Lifting Products DANGER: Overhead lifting presents a very real danger of severe injury or loss of life if lifting equipment is not used properly. O.S.H.A. and ASME have adopted the following requirements for safe operation of all lifting slings. Please read and understand all of these instructions prior to using any lifting sling or sling assembly. Slings should only be used by qualified persons who are responsible for the sling & rigging selection, inspection and use. USE OF THESE PRODUCTS DEMONSTRATES AN UNDERSTANDING OF THESE WARNINGS AND THE RISKS INVOLVED. WORKING LOAD LIMITS AT VARIOUS SLING ANGLES: GRADE 0 CHAIN SIZE SINGLE DOUBLE TRIPLE QUAD 0 Angle of lift 60 Angle 45 Angle 30 Angle 60 Angle 45 Angle 30 Angle (mm) 7/32 /4 (/32) 5/6 /2 5/ 3/4 7/ / ,0 3,500 4,500 7,0,000,0 2,300 34,200 47,700 72,300 3,600 6,0 7,00,300 20,00 3,300 4,000 5,200 2,600 5,200 3,000 4,00 6,400,000 7,000 25,600 40,000 4,400 67,400 2,000 2,0 3,500 4,500 7,0,000,0 2,300 34,200 47,700 72,300 5,450,0,700,400 3,200 47,000 73,500,00 3,00 7,00 4,450 7,400,500 5,0 25,500 3,400 60,000 72,500,200 53,000 3,50 5,200 6,00,600,000 27,0 42,400 5,300 7,500,400 Above Working Load Limits apply only to normal conditions of use in straight configurations and equally loaded legs. For endless slings, we recommend a WLL of 75% of the above WLL for the corresponding double leg sling. Design Factor: 4: WARNING: Never exceed a sling angle of <30. SAFE USE: Inspect all sling components prior to each use. Never use slings that are damaged or defective. Damaged or defective slings must be removed from service immediately. The following conditions constitute a damaged sling: acid or caustic burns, deformation of the chain or attachments, gouges, nicks or other visible abnormalities, stretching of the chain by more than % from original length, wear of chain or any component part by more than % of the original dimensions. Only slings with legible identification tags shall be used. Keep all tags and labels away from the load, hook and point of choke to avoid rendering the tag nonreadable and the sling therefore unusable. If in doubt about the safety of a sling, DO NOT use it without having it proof tested. Slings must never be shortened with knots, bolts, or other makeshift devices nor should they ever be extended from their original length with nonoriginal hardware, fittings or other devices. To safely shorten a chain sling leg a shortening hook or clutch must be used. Never twist or kink the legs of a sling. Always ensure that chain is protected from any corners on the load. Never load in excess of the rated capacity for the application. Consideration must be given to the load angle (see chart above) which affects the rated capacity of the sling. Shock loading shall be avoided. The load applied to a hook shall be centered in the base or bowl of the hook to avoid hook tip overloading. Never tip load a hook. Select only chain slings with suitable characteristics for the load type, hitch and the environment of their use. Chain slings should always be hitched in a manner that provides for control of the load. Always use the correct size and type sling for the load allowing for the included angle and the possibility of unequal loading. Never drag chain slings on the floor. Protect chain and fittings at all times from corners, edges, protrusions, or abrasive surfaces. Never pull slings out from under a load when the load is resting on the sling. Place blocks under the load prior to setting down the load to allow removal of the sling. Do not drop slings. Personnel must keep all body parts from between the sling and the load, and from between the sling and the crane/hoist hook. Persons shall never ride the sling or the load during lifting or while suspended. Persons must stand clear of all loads while lifting or while suspended. During lifting, with or without the load, personnel must be alert for possible snagging of the load or the chain sling. Chain slings should be stored in a properly designed rack. They should never be left lying on the floor where they could suffer mechanical or corrosion damage. Never store slings in areas that are chemically active. Chemicals can destroy the integrity of chain slings in varying degrees that are not always readily apparent upon visual inspection.

11 LIFTING PRODUCTS LIMITATION ON USE: Grade 0 (S) Lifting Products Alloy Chain and chain slings should not be used in acid or caustic solutions or in heavily acidic or caustic laden atmospheres. The high tensile strength of the heat treated alloy material in Alloy Chain and components is susceptible to hydrogen embrittlement when exposed to acids. Chain slings must not be heat treated, galvanized, plated, coated or subjected to any process involving heating or pickling. Each of these processes can have dangerous effects, reducing the strength of the chain and will invalidate the manufacturers certification. Grade 0 Warnings & Info Chain slings may be used at temperatures between 40 F to 400 F (40 c to 205 c) with no reduction in the working load limit. When using slings in exceptionally hazardous conditions such as lifting of potentially dangerous loads, including molten metals and corrosive or fissile material, the degree of hazard should be addressed by a competent person and the working load limit adjusted downward accordingly. Never attempt to repair a damaged sling, replace it immediately. Damaged slings may be repaired only on the advice of the chain sling manufacturer and returned to service only after complete inspection and proof testing. QUALITY ASSURANCE: All Alloy Chain fittings are manufactured under very strict standards and they meet or exceed ASTM A52 requirements. They also comply with all OSHA, ANSI B30., B30., B30.26 and Federal standards for Alloy Lifting Chain components. These quality standards include: Spectrographic analysis to assure the proper metallurgy of the raw materials. Magnaflux Crack Detection on every item to assure proper forging without voids or cracks. Eddy Current detection of all pins to assure the highest quality. Proof Load testing at 2.5x the Working Load Limit with resultant permanent deformation less than %. Dynamic fatigue testing of batch samples to.5x the Working Load Limit for 20,000 cycles. Ultimate break load testing of batch samples in a static tensile testing machine to determine compliance with all design factors. Electro current flow detection of all swivels to assure insulating properties are met. SOME EXAMPLES OF (S) ALLOY CHAIN SLINGS:

12 LIFTING PRODUCTS Grade 0 Alloy Chain & Accessories Grade 0 (S) Alloy Chain Grade 0 Alloy Chain is specifically designed to meet the rigorous requirements of overhead lifting applications set forth by OSHA & ANSI B30., B30. & B Grade 0 (S) Alloy Chain meets industry minimums of 5% elongation factor. A test certificate is provided with each drum. Alloy chain is supplied in a black lacquer finish. Approved For Overhead Lifting Hallmarked: SCC or S every inches Grade 0 (S) Alloy Chain (Full drum) BLACK LACQUER Trade Size (MM) Wire Dia. Inside Link Dimensions A B Feet per drum Lbs per 0 Ft. Working Load Limit (Lbs) (Kgs) H / ,500,5 H / ,500 2,042 H ,0 3,22 H / ,000 5,444 H / ,0,2 Design factor 4: Grade 0 (S) Alloy Chain (Half drum) BLACK LACQUER Trade Size (MM) Wire Dia. Inside Link Dimensions A B Feet per /2 drum Lbs per 0 Ft. Working Load Limit (Lbs) (Kgs) H / ,500,5 H / ,500 2,042 H ,0 3,22 H / ,000 5,444 Design factor 4: Alloy Chain Sling I.D. Tag Blank template for use to meet ID requirements on alloy chain sling assemblies. Stainless steel tag is 2mm thick and is supplied with a 2 diameter plated split ring. STAINLESS STEEL Dimensions H ½ H x 2 W 0.44 / ctn WARNING: Never exceed Working Load Limit. Inspect chain and all attachments prior to each use. Do not use if chain links or components are visibly worn or distorted. Refer to pages & of this catalog for instructions. NOTE: Grade 0 (S) chain is designed for overhead lifting applications. These products meet all O.S.H.A. and ANSI B30., B30., B30.26 construction and rating requirements for overhead lifting chain and attachments. Minimum order quantity: package Catalog weights are approximate

13 LIFTING PRODUCTS Grade 0 (S) Alloy Chain Accessories Alloy chain accessories for use with Grade 0 (S) chain. Made to meet or exceed ASTM A52 specʼs. They are constructed from high alloy steels, drop forged, quenched and tempered. They are all magnaflux inspected for any cracks, proof load tested to 2.5 times the WLL and batch samples are dynamic fatigue tested for 20,000 cycles. All SCC alloy accessories are powdercoat painted in a bright safety yellow or are Zinc Dacromate plated. Alloy Oblong Master Link (Use with alloy connecting link) Approved For Overhead Lifting Grade 0 Alloy Accessories YELLOW PAINT Trade Size Chain Size LEG 2 LEGS Dimensions IL IW D Working Load Limit (Lbs) H /2 / ,000 5 / ctn H / / ,000 5 / ctn H / / ,000 5 / ctn H / 5/ / ,000 5 / ctn Design factor 5: Alloy Oblong Master Link with Flat (Use with alloy omega link) YELLOW PAINT Trade Size Chain Size LEG 2 LEGS Dimensions IL IW D Working Load Limit (Lbs) H /2 / ,000 4 / ctn H / / ,000 4 / ctn H / / ,000 4 / ctn H / 5/ / ,000 4 / ctn Design factor 5: ASSEMBLY & USE OF AN OBLONG MASTER LINK: 2 3 OR = Alloy Omega Connecting Link YELLOW PAINT Chain Size K Dimensions D T P Working Load Limit (Lbs) H /32 ~ 5/ ,500 4 / ctn H ,0 4 / ctn H / ,000 4 / ctn H / ,0 4 / ctn Design factor 4: WARNING: Never exceed Working Load Limit. Inspect chain and all attachments prior to each use. Do not use if chain links or components are visibly worn or distorted. Refer to pages & of this catalog for instructions. NOTE: Grade 0 (S) chain is designed for overhead lifting applications. These products meet all O.S.H.A. and ANSI B30., B30., B30.26 construction and rating requirements for overhead lifting chain and attachments. Catalog weights are approximate Minimum order quantity: package 3

14 LIFTING PRODUCTS Grade 0 Alloy Accessories Alloy Eye Swivel SelfLocking Hook Grade 0 (S) Alloy Chain Accessories Alloy chain accessories for use with Grade 0 (S) chain. Made to meet or exceed ASTM A52 specʼs. They are constructed from high alloy steels, drop forged, quenched and tempered. They are all magnaflux inspected for any cracks, proof load tested to 2.5 times the WLL and batch samples are dynamic fatigue tested for 20,000 cycles. All SCC alloy accessories are powdercoat painted in a bright safety yellow or are Zinc Dacromate plated. Approved For Overhead Lifting YELLOW PAINT Chain Size K P Dimensions B A D T H Working Load Limit (Lbs) H /32 ~ 5/ ,500 Each H ,0 Each H / ,000 Each H / ,0 Each Design factor 4: Alloy Clevis SelfLocking Hook YELLOW PAINT Chain Size A Dimensions K P T H Working Load Limit (Lbs) H /32 ~ 5/ ,500 2 / ctn H ,0 2 / ctn H / ,000 2 / ctn H / ,0 2 / ctn Design factor 4: Alloy Eye Self Locking Hook YELLOW PAINT Chain Size K P Dimensions A D T H Working Load Limit (Lbs) H /32 ~ 5/ ,500 2 / ctn H ,0 2 / ctn H / ,000 2 / ctn H / ,0 2 / ctn Design factor 4: HOW TO USE A SELF LOCKING HOOK: WARNING: Never exceed Working Load Limit. Inspect chain and all attachments prior to each use. Do not use if chain links or components are visibly worn or distorted. Refer to pages & of this catalog for instructions. NOTE: Grade 0 (S) chain is designed for overhead lifting applications. These products meet all O.S.H.A. and ANSI B30., B30., B30.26 construction and rating requirements for overhead lifting chain and attachments. 4 Minimum order quantity: package Catalog weights are approximate

15 LIFTING PRODUCTS Alloy Connecting Link Grade 0 (S) Alloy Chain Accessories Alloy chain accessories for use with Grade 0 (S) chain. Made to meet or exceed ASTM A52 specʼs. They are constructed from high alloy steels, drop forged, quenched and tempered. They are all magnaflux inspected for any cracks, proof load tested to 2.5 times the WLL and batch samples are dynamic fatigue tested for 20,000 cycles. All SCC alloy accessories are powdercoat painted in a bright safety yellow or are Zinc Dacromate plated. Approved For Overhead Lifting Grade 0 Alloy Accessories YELLOW PAINT Chain Size K Dimensions A D B Working Load Limit (Lbs) H /32 ~ 5/ ,500 5 / ctn H ,0 5 / ctn H / ,000 5 / ctn H / ,0 5 / ctn Design factor 4: Alloy Web/Sling Connecting Link (with Coupling Pin & Sleeve) YELLOW PAINT Chain Size A Dimensions B D K W Working Load Limit (Lbs) H /32 ~ 5/ ,500 2 / ctn H ,0 2 / ctn H / ,000 2 / ctn H / ,0 2 / ctn Design factor 4: Alloy Excavator WeldOn Hook YELLOW PAINT Size (Tons) P L Dimensions T H F W A M Working Load Limit (Lbs) H ,200 Each H ,600 Each H ,000 Each H ,000 Each Design factor 5: Alloy Eye Shortening Hook YELLOW PAINT Chain Size K Dimensions G A T F Working Load Limit (Lbs) H62452 /32 ~ 5/ ,500 4 / ctn H ,0 4 / ctn H6252 / ,000 4 / ctn H6252 5/ ,0 4 / ctn Design factor 4: WARNING: Never exceed Working Load Limit. Inspect chain and all attachments prior to each use. Do not use if chain links or components are visibly worn or distorted. Refer to pages & of this catalog for instructions. NOTE: Grade 0 (S) chain is designed for overhead lifting applications. These products meet all O.S.H.A. and ANSI B30., B30., B30.26 construction and rating requirements for overhead lifting chain and attachments. Catalog weights are approximate Minimum order quantity: package 5

16 LIFTING PRODUCTS Grade 0 Alloy Accessories Alloy Twist Eye Choke Hook Grade 0 (S) Alloy Chain Accessories Alloy chain accessories for use with Grade 0 (S) chain. Made to meet or exceed ASTM A52 specʼs. They are constructed from high alloy steels, drop forged, quenched and tempered. They are all magnaflux inspected for any cracks, proof load tested to 2.5 times the WLL and batch samples are dynamic fatigue tested for 20,000 cycles. All SCC alloy accessories are powdercoat painted in a bright safety yellow or are Zinc Dacromate plated. Approved For Overhead Lifting YELLOW PAINT Chain Size K Dimensions C A Working Load Limit (Lbs) H /32 ~ 5/ ,500 6 / ctn H ,0 6 / ctn H / ,000 6 / ctn H / ,0 6 / ctn Design factor 4: Alloy Clevis Sling Hook with Latch YELLOW PAINT Chain Size A Dimensions K P T H Working Load Limit (Lbs) H /32 ~ 5/ ,500 5 / ctn H ,0 5 / ctn H / ,000 5 / ctn H / ,0 5 / ctn Design factor 4: Alloy Eye Sling Hook with Latch YELLOW PAINT Chain Size K Dimensions P A D T H Working Load Limit (Lbs) H /32 ~ 5/ ,500 4 / ctn H ,0 4 / ctn H / ,000 4 / ctn H / ,0 4 / ctn Design factor 4: Alloy Clevis Claw YELLOW PAINT Chain Size A/B Dimensions C D E F Working Load Limit (Lbs) H /32 ~ 5/ ,500 4 / ctn H ,0 4 / ctn H / ,000 4 / ctn H / ,0 4 / ctn Design factor 4: WARNING: Never exceed Working Load Limit. Inspect chain and all attachments prior to each use. Do not use if chain links or components are visibly worn or distorted. Refer to pages & of this catalog for instructions. NOTE: Grade 0 (S) chain is designed for overhead lifting applications. These products meet all O.S.H.A. and ANSI B30., B30., B30.26 construction and rating requirements for overhead lifting chain and attachments. 6 Minimum order quantity: package Catalog weights are approximate

17 LIFTING PRODUCTS YELLOW PAINT H Chain Size /32 ~ 5/6 P 0.3 Grade 0 (S) Alloy Chain Accessories Alloy chain accessories for use with Grade 0 (S) chain. Made to meet or exceed ASTM A52 specʼs. They are constructed from high alloy steels, drop forged, quenched and tempered. They are all magnaflux inspected for any cracks, proof load tested to 2.5 times the WLL and batch samples are dynamic fatigue tested for 20,000 cycles. All SCC alloy accessories are powdercoat painted in a bright safety yellow or are Zinc Dacromate plated. Alloy Clevis Grab Hook (Not for use with Omega Link) Dimensions A F K H L Working Load Limit (Lbs) 4,500 5 / ctn Approved For Overhead Lifting Grade 0 Alloy Accessories H ,0 5 / ctn H / ,000 5 / ctn H / ,0 5 / ctn Design factor 4: Alloy Eye Grab Hook (Not for use with Omega Link) YELLOW PAINT Chain Size P Dimensions A G K F Working Load Limit (Lbs) H /32 ~ 5/ ,500 5 / ctn H ,0 5 / ctn H / ,000 5 / ctn H / ,0 5 / ctn Design factor 4: Alloy Screw Pin Anchor Shackle Forged alloy steel with alloy pin. Fatigue rated. Size and Working Load Limit permanently shown on each shackle. Meets performance requirements of Federal Specification RRC27D, Type IV A, Grade B, Class 2. ZINC DACROMATE Trade Size W D Dimensions A B E G H Working Load Limit (Lbs) H / ,650 4 / ctn H ,400 4 / ctn H / ,725 4 / ctn H62503 / ,500 4 / ctn H / ,000 4 / ctn H6253 3/ ,400 2 / ctn H6253 7/ ,50 2 / ctn H6253 Design factor 4.5: ,550 2 / ctn WARNING: Never exceed Working Load Limit. Inspect chain and all attachments prior to each use. Do not use if chain links or components are visibly worn or distorted. Refer to pages & of this catalog for instructions. WARNING: Inspect all shackles for distortion or damage prior to use. If the pin or eye is worn or distorted, remove the shackle from service immediately and replace. Do not use screw pin anchor shackles in applications where the thumb grip could be hit and cause pin movement. Use safety shackles in these applications. All Working Load Limits stated are for a straight pull, perpendicular against the pin. If the pull is angular, the load must be on the bow and the stated working load is reduced by 30% at 45 and 50% at 0. NOTE: Grade 0 (S) chain is designed for overhead lifting applications. These products meet all O.S.H.A. and ANSI B30., B30., B30.26 construction and rating requirements for overhead lifting chain and attachments. Catalog weights are approximate Minimum order quantity: package 7

18 LIFTING PRODUCTS Grade 0 Alloy Accessories YELLOW PAINT H Grade 0 (S) Alloy Chain Accessories Alloy chain accessories for use with Grade 0 (S) chain. Made to meet or exceed ASTM A52 specʼs / EN677 standard. They are constructed from high alloy steels, drop forged, quenched and tempered. They are all magnaflux inspected for any cracks, proof load tested to 2.5 times the WLL and batch samples are dynamic fatigue tested for 20,000 cycles. All SCC alloy accessories are powdercoat painted in a bright safety yellow or are Zinc Dacromate plated. Alloy Clutch Sling Hook with Locking Clutch Chain Size /32 ~ 5/6 A 0.3 B 0.40 Dimensions C K H P L 6.75 T Working Load Limit (Lbs) 4,500 2 / ctn Approved For Overhead Lifting H ,0 2 / ctn H / ,000 2 / ctn H / ,0 2 / ctn Design factor 4: ASSEMBLY & USE OF ALLOY CLUTCH SLING HOOK: Adjustable leg sling with locking clutch hook. Adjustable leg sling without locking clutch hook (oldstyle). Alloy WeldOn Lifting Point / TieDown Anchor YELLOW PAINT Size (Tons) W D Dimensions F K H R L Working Load Limit (Lbs) H ,200 5 / ctn H ,600 5 / ctn H ,000 5 / ctn Design factor 5: Alloy BoltOn Lifting Point / TieDown Anchor Grade bolts required (Supplied without bolts). YELLOW PAINT Size (Tons) A B Dimensions D F K H M L R Working Load Limit (Lbs) H ,200 5 / ctn H ,600 5 / ctn H Design factor 5: ,000 5 / ctn WARNING: Never exceed Working Load Limit. Inspect chain and all attachments prior to each use. Do not use if chain links or components are visibly worn or distorted. Refer to pages & of this catalog for instructions. NOTE: Grade 0 (S) chain is designed for overhead lifting applications. These products meet all O.S.H.A. and ANSI B30., B30., B30.26 construction and rating requirements for overhead lifting chain and attachments. Minimum order quantity: package Catalog weights are approximate

19 LIFTING PRODUCTS Replacement Trigger for SelfLocking Hooks (For SCC G0 alloy hooks only) BLACK H Grade 0 (S) Alloy Chain Accessories Alloy chain accessories for use with Grade 0 (S) chain. Made to meet or exceed ASTM A52 specʼs. They are constructed from high alloy steels, drop forged, quenched and tempered. They are all magnaflux inspected for any cracks, proof load tested to 2.5 times the WLL and batch samples are dynamic fatigue tested for 20,000 cycles. All SCC alloy accessories are powdercoat painted in a bright safety yellow or are Zinc Dacromate plated. Application For hook size: /32 ~ 5/ Working Load Limit (Lbs) N/A / ctn Approved For Overhead Lifting Grade 0 Alloy Accessories H For hook size: 0.66 N/A / ctn H For hook size: / N/A / ctn H For hook size: 5/.00 N/A / ctn Replacement Latch Kit for Alloy Excavator WeldOn Hook YELLOW Application Working Load Limit (Lbs) H6052 For Ton excavator hook 0.33 N/A 5 / ctn H60352 For 3 Ton excavator hook 0.66 N/A 5 / ctn H60552 For 5 Ton excavator hook.40 N/A 5 / ctn H6052 For Ton excavator hook 2.20 N/A 5 / ctn Alloy Replacement Latch Kit (For SCC G0 alloy hooks only) BRIGHT ZINC Application Working Load Limit (Lbs) H6504 For hook size: /32 ~ 5/ N/A 5 / ctn H6506 For hook size: 0.0 N/A 5 / ctn H650 For hook size: /2 0. N/A 5 / ctn H650 For hook size: 5/ 0.25 N/A 5 / ctn Replacement Clevis Load Pin (For SCC G0 alloy hooks only) BRIGHT ZINC Application Working Load Limit (Lbs) H For hook size: /32 ~ 5/ ,500 5 / ctn H For hook size: 0.0 7,0 5 / ctn H76000 For hook size: /2 0.20,000 5 / ctn H76000 For hook size: 5/ 0.35,0 5 / ctn Design factor 4: WARNING: Never exceed Working Load Limit. Inspect chain and all attachments prior to each use. Do not use if chain links or components are visibly worn or distorted. Refer to pages & of this catalog for instructions. NOTE: Grade 0 (S) chain is designed for overhead lifting applications. These products meet all O.S.H.A. and ANSI B30., B30., B30.26 construction and rating requirements for overhead lifting chain and attachments. Catalog weights are approximate Minimum order quantity: package

20 LIFTING PRODUCTS Grade 0 Alloy Accessories Alloy Insulated Blank Swivel (with Ball Bearing) Grade 0 (S) Alloy Chain Accessories The perfect system for universal coupling of components to chain and wire rope, as well as synthetic slings. Heavy hoisting with a strong but lightweight system. Components are forged, high alloy steel compatible with alloy chain and fittings. Assembly is fast and easy using only a hammer. For use with Grade 0 (S) chain. All alloy accessories (except blank swivel) are powdercoat painted in a bright safety yellow. Individually tested to resist 500 Volts. Test certificate provided with each swivel. Designed for protection of overhead crane during welding operations on suspended loads. Approved For Overhead Lifting BLACK Chain Size D Dimensions L Working Load Limit (Lbs) H /32 ~ 5/ ,500 Each H ,0 Each H / ,000 Each H / ,0 Each Design factor 4: SWIVEL & COUPLING ACCESSORIES USAGE CHART: Alloy Coupling Sling Hook with Latch YELLOW PAINT Chain Size K Dimensions P T H Working Load Limit (Lbs) H /32 ~ 5/ ,500 2 / ctn H ,0 2 / ctn H / ,000 2 / ctn H Design factor 4: 5/ ,0 2 / ctn WARNING: Never exceed Working Load Limit. Inspect chain and all attachments prior to each use. Do not use if chain links or components are visibly worn or distorted. Refer to pages & of this catalog for instructions. NOTE: Grade 0 (S) chain is designed for overhead lifting applications. These products meet all O.S.H.A. and ANSI B30., B30., B30.26 construction and rating requirements for overhead lifting chain and attachments Minimum order quantity: package Catalog weights are approximate

21 LIFTING PRODUCTS Alloy Coupling SelfLocking Hook YELLOW PAINT H H H H Design factor 4: Chain Size /32 ~ 5/6 /2 5/ K Grade 0 (S) Alloy Chain Accessories Alloy chain accessories for use with Grade 0 (S) chain. Made to meet or exceed ASTM A52 specʼs. They are constructed from high alloy steels, drop forged, quenched and tempered. They are all magnaflux inspected for any cracks, proof load tested to 2.5 times the WLL and batch samples are dynamic fatigue tested for 20,000 cycles. All SCC alloy accessories are powdercoat painted in a bright safety yellow or are Zinc Dacromate plated. Dimensions P T H Working Load Limit (Lbs) 4,500 7,0,000 Each Each Each,0 Each Approved For Overhead Lifting Grade 0 Alloy Accessories Alloy Coupling Master Link (Open) YELLOW PAINT Chain Size K Dimensions W T H A Working Load Limit (Lbs) H /32 ~ 5/ ,500 Each H ,0 Each H / ,000 Each H / ,0 Each Design factor 4: Alloy /2 Coupling Link w/ Pin and Sleeve YELLOW PAINT Chain Size K Dimensions A D L Working Load Limit (Lbs) H /32 ~ 5/ ,500 / ctn H ,0 / ctn H / ,000 / ctn H / ,0 / ctn Design factor 4: Alloy Coupling Pin and Sleeve (Use with SCC alloy connecting & alloy coupling items) BRIGHT ZINC Chain Size d Dimensions D L W Working Load Limit (Lbs) H /32 ~ 5/ ,500 / ctn H ,0 / ctn H / ,000 / ctn H Design factor 4: 5/ ,0 / ctn WARNING: Never exceed Working Load Limit. Inspect chain and all attachments prior to each use. Do not use if chain links or components are visibly worn or distorted. Refer to pages & of this catalog for instructions. NOTE: Grade 0 (S) chain is designed for overhead lifting applications. These products meet all O.S.H.A. and ANSI B30., B30., B.30., B30.26 construction and rating requirements for overhead lifting chain and attachments. Catalog weights are approximate Minimum order quantity: package 2

22

23 Section 2 Cargo Control Cargo Control Warnings & Info Utility Straps Tiedown Anchors... 2 Cargo Nets... 2 Strap Assemblies Ratchet Strap Assembly Strap Assembly Parts Strap Assemblies Strap Assemblies Interior Van Straps BoardClamp ETrack Marine... 3 Strap Hardware (bulk packaging). 345 Winches Winch Bars... 4 Corners & Hard Parts... 4 Strap Winder... 4 CargoGuard... 4 Rubber Rope... 4 Tarp Straps... 4 Stretch Cords... 4 Trailer Safety Chain & Hooks AutoTie Downs... 5 Towing Straps & Chains Cable Pullers Cargo Bars and Loadlocks SCC SmartBar SCC SecureBar Loadlocks & Parts Loadbinders SCC QuikBinder PLUS Ratchet Binders SCC ProLok Lever Binders... 5 Chain Assemblies... 56

24 CARGO CONTROL All Cargo Control Products WARNING: Read and follow all instructions prior to use. Failure to do so could result in property damage, serious personal injury, and/or loss of life. No use other than that which the product was designed is recommended or endorsed and all such use is against the recommendation of the manufacturer. Working Load Limit ratings (WLL) are based on the strength of the assembly and components when new. Always consider age, and condition of assembly and components to determine the quantity to use to sufficiently secure the load. USE OF THESE PRODUCTS DEMONSTRATES AN UNDERSTANDING OF THESE WARNINGS AND THE RISKS INVOLVED. WARNING: Observe all tie down requirements of the Commercial Vehicle Safety Alliance (C.V.S.A.) "Vehicle Inspection Criteria", Federal Department of Transportation (D.O.T.) FMCSA 4 CFR Parts 3233, CCMTA (Canadian Council of Motor Transport Administrators) NSCStandard or other local regulations governing cargo restraint and tie down. Use only products that are rated and tagged with working load limits (WLL) for cargo tie down applications. Warnings & Technical info SAFE USE: Inspect all tie down components prior to each use. Never use items that are damaged, worn or defective. Remove them from service immediately and replace with new. Do not attempt to repair. The following conditions constitute a damaged tie down strap: acid or caustic burns, melting of any part of the web surface, broken or worn stitching, distortion of eyes or fittings, or web snags, cuts, tears, and punctures. Only tie down straps with legible identification tags should be used. Keep all tags and labels away from the load, vehicle body and winch to avoid tag damage rendering the tag nonreadable and the strap assembly therefore unusable. The following conditions constitute a damaged tie down chain assembly: damaged or distorted links, distortion of eyes or hooks, nicks or gouges in the chain or hooks. If in doubt about the safety of a tie down component or assembly do not use it. Loadbinders should not be used if any of the previous conditions exist or if the handles are bent or distorted. Winches (Pg. 4647) WARNING: Failure to comply with these instructions may result in property damage, serious personal injury and/or loss of life. Winches must be attached to a structurally sound frame element capable of withstanding and sustaining the maximum load of the winch and strap assembly. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handles, bars and other binding equipment as it could release without warning and with extreme force. USE OF THESE PRODUCTS DEMONSTRATES AN UNDERSTANDING OF THESE WARNINGS AND THE RISKS INVOLVED. INSTALLATION: Mount & position the winch so that the latch / pawl drops into the gear sprocket teeth by its own weight. Portable and slider winches must be positioned not to interfere with any other trailer components ( ie: tire clearance). Set screws on portable winches should be snug tightened only. Over tightening can cause bracket to bend or break resulting in possible failure and loss of tie down. Portable winches must be removed from trailer and stored when not in use. For weldon type winches, a continuous /4" fillet weld, 4" long on both sides of the winch frame, with /" minimum penetration is required. (use a filler wire compatible with ANSI 5 steel.) MAINTENANCE: The winch assembly should be protected from corrosion by application of a rust inhibiting paint. Avoid paint build up in the latch/pawl area that may inhibit the free movement of its parts. A light oil should be used to keep these parts moving freely to insure safe operation. PROPER USE: The loose end of the web assembly should be inserted through the web slot in the winch mandrel and the excess web pulled through. After tensioning, there must be 23 full wraps of webbing around the mandrel. Less wraps may result in web slippage. More wraps will cause additional strain to be exerted on the winch assembly and reduce the load capacity of the winch. Cable/wire rope must be used only on winches designed for their use. To use, twist an eye on the end of the cable with at least 2 feet of loose tail. Place the eye over the cable pin on the winch mandrel and tighten the winch, wrapping the cable over the loose tail a minimum of 4 times to secure the cable from slippage. CAUTION: Inspect all strap and winch assembly components prior to each use for damage or deterioration. Remove damaged product from service immediately and replace. Do not attempt to repair. Use extreme caution when tensioning the winch assembly to assure the latch/pawl is fully engaged in the gear sprocket teeth before releasing the pressure on the winch bar. Always keep hands and fingers away from the winch pawl. Always make sure that the load is adequately secured prior to movement of the vehicle using a sufficient quantity of appropriate strength tie downs. Never exceed the Working Load Limit of either the tie down or the hardware/winch. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. All component parts must meet or exceed CVSA guidelines, Federal DOT Regulation, CCMTA regulations as well as local regulations. Tie downs must be checked periodically during transit and retensioned as needed to maintain a secure load. Never modify a winch to perform any use other than that for which it was specifically designed. Misuse or modification of any type will result in voiding any or all of the warranty and liability by the manufacturer/seller. 24

25 CARGO CONTROL Winch Bars (Pg. 4) WARNING: Failure to comply with these instructions may result in property damage, serious personal injury and/or loss of life. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handles, bars and other binding equipment as it could release without warning and with extreme force. USE OF THESE PRODUCTS DEMONSTRATES AN UNDERSTANDING OF THESE WARNINGS AND THE RISKS INVOLVED. PROPER USE: Use extreme caution when tensioning the winch/assembly to assure the latch/pawl is fully engaged in the gear sprocket teeth before releasing the pressure on the winch bar. Always keep hands and fingers away from the winch pawl & keep face, head and body out of path of winch bar. Inspect all binding components, (winch, strap assembly, chain assembly, loadbinder) prior to each use. Never use damaged or worn equipment. Remove from service and replace with new. Do not attempt to repair. Winch bars are used entirely at the users own risk and the use of a winch bar demonstrates an understanding of the risks and a willingness to accept the consequences of possible property damage, serious personal injury and/or loss of life. When using SCC winch bars with winches: the tapered point of the bar must be inserted completely through both holes in the winch cap. Failure to insert bar correctly could cause the bar to slip and result in serious personal injury and/or loss of life. During tightening and before releasing the tie down assembly, check the winch pawl to insure it has properly engaged the gear sprocket. Always grip the winch bar at the knurled section of the bar for increased safety. When using SCC winch bar with binders: only use combination winch bars designed with a binder cradle to assist in tightening a loadbinder. Insure that the loadbinder handle is fully inserted into the winch bar cradle and locked in place. Keep head and body out of the path of the loadbinder handle in case of slippage or kickback. Failure to do so may result in serious personal injury and/or loss of life. Tow Straps and Tow Chains (Pg. 52) Warnings & Technical info DANGER: PLEASE READ AND UNDERSTAND ALL OF THESE INSTRUCTIONS PRIOR TO USING ANY TOW CHAIN OR TOW STRAP. Towing or recovery of a vehicle presents a very real danger of property damage, serious personal injury and/or loss of life. Never attach fittings that have a strength rating (WLL) less than the assembly to which they are being attached. Insure that the chain or strap is attached to a secure part on both vehicles capable of withstanding the forces involved in towing or recovery. Woven fabric straps store energy that when released could cause a whipping action and endanger operators and bystanders. Keep all persons away from the vehicles and strap or chain during towing or recovery. USE OF THESE PRODUCTS DEMONSTRATES AN UNDERSTANDING OF THESE WARNINGS AND THE RISKS INVOLVED. PROPER USE AND CARE: Tow chains and tow straps are designed for general purpose towing and recovery only. They are not intended to be used for highway towing or for extended periods of time. In these cases, a tow bar is required for safe operation. Tow chains/straps should never be used in a manner where failure of either the chain/strap, attachments or vehicle anchor points could result in personal injury. Keep all persons a safe distance away from all vehicles during a tow or recovery operation. The Working Load Limit shown in this catalog or on the package or assembly should never be exceeded. This is the maximum safe load that the assembly should ever be exposed to when in a like new condition. Apply tension in a gradual and uniform manner to avoid shock loading the assembly which could cause failure. Be sure that the assembly is not twisted, kinked, or knotted. Never subject the chain or strap to sharp edges as these can damage the chain or even cut the strap. If unavoidable, use caution and pad the area with rubber or similar material (a cut section of tire can be used for this purpose). Inspect all assemblies and attachments prior to use for any visible signs of damage. The following will reduce the Working Load Limit of the assembly: a.) Tip loading of hooks, twisting, kinks, knots or improper attachments; b.) Deterioration of the assembly or attachments caused by wear, usage, UV degradation, chemicals, acids, corrosion, cuts, abrasions, high heat exposure, misuse or abuse; c.) Impact caused by jerking or snatching. After use, inspect assembly and attachments for any visible signs of damage prior to storage. Clean and store in a cool and dry place, out of direct sunlight, where damage to the assembly or attachments is not likely to occur. Cargo Bars & Loadlocks (Pg. 5355) WARNING: Failure to understand these instructions and warnings could cause serious personal injury or property damage. Use of these products demonstrates an understanding of these warnings/instructions and the risks involved. Do not use bars to support ANY vertical loads. SCC SmartBars TM and loadlocks are NOT designed to be used as a shoring beam. Using these bars as a step is not advised and could result in serious personal injury. Cargo bars and loadlocks are not designed to secure cargo inside a trailer, only to assist in the stability of a load. SCC SmartBars TM and loadlocks are designed to push out approximately one inch against flexible van trailer walls and can be damaged if used against immovable objects such as door frames. To avoid damaging the bars and trailer, never use more than one hand to close the lever. On the SCC SmartBar TM push handle release button when fully retracted to extend. A stop keeps the bar from sliding open when fully retracted and must be released before operating the lever or the bar can be damaged. To disengage lock, push on handle release tab. 25

26 CARGO CONTROL Premium Polyester Web Straps All SCC strap assemblies are packaged in tamperresistant, durable, sonic welded clam shells. These retail packages are slotted for pegboard hooks and will also stand for counter top display. Each package includes complete instructions for use. These versatile straps are great for securing boats, motorcycles, ATVs, etc. Blue Blk/Wht Black Red Blue and Black straps feature 4,500 Lb. webbing. Blk/Wht and Red straps feature 2,500 Lb. webbing. Ratchet Assembly with JHooks & Rings Utility Straps Strap features a plated J hook and floating D ring on each end that can be secured through truck stake holes, eye bolts, etc. Premium ratchetstyle buckle for easy tightening. *Denotes heavy duty ratchet. CC6 * CC0 Description (Length) (Color) 6 20 Working Load Limit LBS KGS , / ctn / ctn * CC6 6, / ctn Design factor 3: Utility Lashing Strap (with easy release CAM buckle) This universal strap secures anything with a circumference of less than the assembly length. Loose end feeds through easy release CAM buckle. CC4 Description (Length) (Color) Working Load Limit LBS KGS / ctn Design factor 3: Utility Lashing Strap (with ratchet) This universal strap secures anything with a circumference of less than the assembly length. Loose end feeds through premium ratchetstyle buckle. CC45 Description (Length) (Color) 5 Working Load Limit LBS KGS pr. / ctn Design factor 3: Easy Release Tiedown with S Hooks Strap features one vinyl coated hook, one zinc plated hook and an easy release CAM buckle. CC606 Description (Length) (Color) 6 Working Load Limit LBS KGS / ctn CC pr. / ctn CC / ctn Design factor 3: WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

27 CARGO CONTROL Premium Polyester Web Straps All SCC strap assemblies are packaged in tamperresistant, durable, sonic welded clam shells. These retail packages are slotted for pegboard hooks and will also stand for counter top display. Each package includes complete instructions for use. These versatile straps are great for securing boats, motorcycles, ATVs, etc. Ratchet Tiedown with S Hooks One vinyl coated hook, one zinc plated hook. Premium ratchetstyle buckle for easy tightening. *Denotes heavy duty ratchet. CC5 Description (Length) (Color) 5 Working Load Limit LBS KGS / ctn * CC5 Design factor 3: 5, / ctn Utility Straps Soft Strap Tiedown Extension These soft straps have 2 sewn loops and no metal fittings. They are used as strap extensions where a strap end with no hardware is preferred. d in pairs. CC22 Description (Length) (Color) Working Load Limit LBS KGS, pr./ ctn CC24 24, pr./ ctn Design factor 3: Ratchet Tiedown with Chrome S Hooks (Highly visible web) Strap features black webbing with 2 white tracers that reflect light for higher visibility at night. The premium ratchet buckle and hooks are chrome plated for added appeal. CC52 Description (Length) (Color) 6 Working Load Limit LBS KGS / ctn CC / ctn Design factor 3: Cam Buckle Tiedown with Chrome S Hooks (Highly visible web) Strap features black webbing with 2 white tracers that reflect light for higher visibility at night. Hooks are chrome plated for added appeal. CC652 Description (Length) (Color) 6 Working Load Limit LBS KGS / ctn Design factor 3: WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 27

28 CARGO CONTROL Economy Polyester Web Straps All SCC strap assemblies are packaged in tamperresistant, durable, sonic welded clam shells. These retail packages are slotted for pegboard hooks and will also stand for counter top display. Each package includes complete instructions for use. These versatile straps are great for securing boats, motorcycles, ATVs, etc. Ratchet Tiedown with J Hooks Zinc plated hardware. Premium ratchetstyle buckle for easy tightening. Description (Length) (Color) Working Load Limit LBS KGS Utility Straps CC4 CC45 CC50 Design factor 3: pr./ ctn / ctn / ctn Easy Release Tiedown with S Hooks Easy release, zinc plated cam buckle and chrome plated Shooks. d in pairs. CC640 Description (Length) (Color) 4 Working Load Limit LBS KGS pr./ ctn CC pr./ ctn Design factor 3: Easy Release Tiedown with J Hooks Easy release, zinc plated cam buckle and zinc plated J hooks. d in pairs. CC646 Description (Length) (Color) 6 Working Load Limit LBS KGS pr./ ctn Design factor 3: Ratchet Tiedown with S Hooks Chrome plated hooks and a premium chrome plated ratchetstyle buckle for easy tightening. CC4 Description (Length) (Color) 6 Working Load Limit LBS KGS pr./ ctn CC / ctn CC / ctn Design factor 3: WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting. 2 Minimum order quantity: package Catalog weights are approximate

29 CARGO CONTROL Anchors and Cargo Nets TieDown Anchors & Cleats Tiedown anchors fit into stake holes on pickup beds or utility trailers and provide a secure attachment point for straps. Cleats can be mounted on the side of a truck bed or a utility trailer and used to provide a secure location to attach utility straps or other tie downs such as rope. All are chrome plated for added appeal. Pickup tiedown rope cleats CC35 Quantity per Pkg: 2 / card : 0.75 Lbs. / pair : pr./ ctn WLL: 250 Lbs. / 4 Kgs. Design factor 3: Pickup tiedown cleat (flat) CC37 Quantity per Pkg: / card : 0.50 Lbs. / each : / ctn WLL: 250 Lbs. / 4 Kgs. Design factor 3: Pickup stake bed anchor CC3 Quantity per Pkg: 2 / clamshell : 2.00 Lbs./ pair : pr./ ctn WLL: 366 Lbs. / 66 Kgs. Design factor 3: PopUp Anchor Point CC3 Quantity per Pkg: 2 / clamshell :.00 Lbs. / pair : pr./ ctn WLL: 250 Lbs. / 4 Kgs. Design factor 3: TieDown Accessories Cargo Nets Stretch cords are formed into a net pattern to secure cargo in the back of a pickup, SUV or automobile trunk. These nets have oversized plastic hooks for easy attachment. They will work with almost any cargo to assist in hauling it securely. Available in black only. Size Cord Dia. (mm) package CC x / ctn CC x / ctn CC x / ctn CC x / ctn WARNING: Failure to comply with instructions may result in property damage, serious personal injury or death. Rubber and elastic items store energy which can release suddenly, causing serious injury. Stay clear of stretchable items when installing and at all times when tension is applied. This energy could release without warning and with force. Eye protection is recommended at all times. These items are not designed for cargo restraint or tiedown. They are only designed to hold tarp covers in place. Do not use if product shows cuts, cracks, fraying or if hooks are bent or damaged. These products are NOT designed or approved for overhead lifting. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 2

30 CARGO CONTROL 2 Inline Ratchet Strap Assemblies All SCC heavy duty 2 cargo strap assemblies are made from premium, yellow,,000 Lb. tensile strength tested, polyester webbing for maximum durability. Meets all the requirements of the U.S. Department of Transportation (DOT), Canadian Council of Motor Transport Administrators (CCMTA) and Commercial Vehicle Safety Alliance (CVSA). 2 inline strap assemblies come standard with a fixed end. d in shrink wrapped plastic with a circle card. Standard Handle Ratchet with Flat Hooks Strap Assemblies CC27 CC230 Design factor 3: Length (Feet) Working Load Limit LBS KGS 3,300,47 3,300, Standard Handle Ratchet with J Hooks / ctn / ctn CC2327 Length (Feet) 27 Working Load Limit LBS KGS 3,300, / ctn CC ,300, / ctn Design factor 3: Standard Handle Ratchet with Grab Hooks CC2527 Length (Feet) 27 Working Load Limit LBS KGS 3,300, / ctn Design factor 3: Wide Handle Ratchet with Chain Hooks Denotes extra long, wide handle ratchet. * * CC2545 CC2557 Design factor 3: Length (Feet) 5 27 Working Load Limit LBS KGS 3,300,47 3,300, / ctn 4 / ctn WARNING: Never exceed Working Load Limit as stated in catalog and on strap tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233, CCMTA and the C.V.S.A inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

31 CARGO CONTROL 2 Inline Ratchet Strap Assemblies All SCC heavy duty 2 cargo strap assemblies are made from premium, yellow,,000 Lb. tensile strength tested, polyester webbing for maximum durability. Meets all the requirements of the U.S. Department of Transportation (DOT), Canadian Council of Motor Transport Administrators (CCMTA) and Commercial Vehicle Safety Alliance (CVSA). 2 inline strap assemblies come standard with a fixed end. d in shrink wrapped plastic with a circle card. Wide Handle Ratchet with Flat Hooks CC2627 Length (Feet) 27 Working Load Limit LBS KGS 3,300, / ctn CC2630 CC2640 Design factor 3: ,300 3,300,47, / ctn 4 / ctn Strap Assemblies Wide Handle Ratchet with D Rings CC2677 Length (Feet) 27 Working Load Limit LBS KGS 3,300, / ctn CC ,300, / ctn Design factor 3: Wide Handle Ratchet with Flat Snap Hooks CC2777 Length (Feet) 27 Working Load Limit LBS KGS 3,300, / ctn CC ,300, / ctn Design factor 3: Wide Handle Ratchet with J Hooks CC227 Length (Feet) 27 Working Load Limit LBS KGS 3,300, / ctn CC ,300, / ctn Design factor 3: WARNING: Never exceed Working Load Limit as stated in catalog and on strap tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233, CCMTA and the C.V.S.A inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 3

32 CARGO CONTROL 2 Strap Assembly Component Parts All SCC heavy duty 2 cargo strap assemblies are made from premium, yellow,,000 Lb. tensile strength tested, polyester webbing for maximum durability. Meets all the requirements of the U.S. Department of Transportation (DOT), Canadian Council of Motor Transport Administrators (CCMTA) and Commercial Vehicle Safety Alliance (CVSA). 2 inline strap assemblies come standard with a fixed end. d in shrink wrapped plastic with a circle card. 2 Inline Adjustable End Strap with Hardware CC202 Width 2 Length (Feet) 2 Description Flat hook Working Load Limit LBS KGS 3,300, / ctn CC202 CC203 Strap Assemblies CC203 2 CC204 2 CC205 2 CC206 2 CC207 2 Design factor 3: Flat snap hook D ring J hook Grab hook Chain & hook 3,300 3,300 3,300 3,300 3,300,467,467,467,467, / ctn 2.0 / ctn 2.75 / ctn 3.2 / ctn 4.5 / ctn CC204 CC206 CC205 CC207 2 Inline Fixed End Strap with Hardware CC20 Width 2 Length Description D ring Working Load Limit LBS KGS 3,300, / ctn CC20 CC202 CC202 CC J hook Flat hook 3,300 3,300,467, / ctn / ctn CC203 CC204 CC204 2 Grab hook 3,300, / ctn CC Chain & hook 3,300, / ctn CC206 2 Flat snap hook 3,300, / ctn CC205 CC206 Design factor 3: Replacement Ratchets These ratchets are barcoded for retail sale. See pages 340 for bulk package ratchets. CC202 Size 2 Description Standard ratchet Working Load Limit LBS KGS 3,670, / ctn CC202 CC204 CC204 2 Short wide ratchet 3,670, / ctn CC205 2 Extra long wide ratchet 3,670, / ctn CC34 3 Design factor 3: Standard ratchet 5,600 2, / ctn CC205 CC34 WARNING: Never exceed Working Load Limit as stated in catalog and on strap tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233, CCMTA and the C.V.S.A inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

33 CARGO CONTROL 3 Strap Assemblies All SCC heavy duty 3 cargo strap assemblies are made from premium, yellow, 5,000 Lb. tensile strength tested, polyester webbing for maximum durability. Meets all requirements of the U.S. Department of Transportation (DOT), Canadian Council of Motor Transport Administrators (CCMTA) and Commercial Vehicle Safety Alliance (CVSA). 3 inline strap assemblies come standard with a fixed end. d in shrink wrapped plastic with a circle card. Flat Hook Strap Assembly CC3027 Length (Feet) 27 Working Load Limit LBS KGS 4,000, / ctn CC ,000, / ctn Design factor 3: Grab Hook Strap Assembly CC3427 Length (Feet) 27 Working Load Limit LBS KGS 4,000, / ctn Strap Assemblies CC ,000, / ctn Design factor 3: VIron Strap Assembly CC3527 Length (Feet) 27 Working Load Limit LBS KGS 4,000, / ctn CC ,000,4 4.0 / ctn Design factor 3: Standard Ratchet with Flat Hooks CC3626 Length (Feet) 27 Working Load Limit LBS KGS 4,000, / ctn CC ,000, / ctn Design factor 3: Standard Ratchet with Grab Hooks CC3636 Length (Feet) 27 Working Load Limit LBS KGS 4,000, / ctn CC363 Design factor 3: 30 4,000, / ctn WARNING: Never exceed Working Load Limit as stated in catalog and on strap tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233, CCMTA and the C.V.S.A inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 33

34 CARGO CONTROL 4 Strap Assemblies All SCC heavy duty 4 cargo strap assemblies are made from premium, yellow, 20,000 Lb. tensile strength tested, polyester webbing for maximum durability. Meets all requirements of the U.S. Department of Transportation (DOT), Canadian Council of Motor Transport Administrators (CCMTA) and Commercial Vehicle Safety Alliance (CVSA). 4 inline strap assemblies come standard with a fixed end. d in shrink wrapped plastic with a circle card. Flat Hook Strap Assembly CC4027 Length (Feet) 27 Working Load Limit LBS KGS 5,000 2, / ctn CC ,000 2,26 5. / ctn Strap Assemblies CC ,000 Design factor 3: Sewn Loop Strap Assembly 2, / ctn CC47 Length (Feet) 27 Working Load Limit LBS KGS 5,000 2, / ctn CC ,000 2,26 4. / ctn Design factor 3: Chain & Hook Strap Assembly CC4227 Length (Feet) 27 Working Load Limit LBS KGS 5,000 2, / ctn CC ,000 2, / ctn Design factor 3: Plain Strap (Without hardware) CC4327 Length (Feet) 2 Working Load Limit LBS KGS 5,000 2, / ctn CC ,000 2, / ctn Design factor 3: WARNING: Never exceed Working Load Limit as stated in catalog and on strap tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233, CCMTA and the C.V.S.A inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

35 CARGO CONTROL 4 Strap Assemblies All SCC heavy duty 4 cargo strap assemblies are made from premium, yellow, 20,000 Lb. tensile strength tested, polyester webbing for maximum durability. Meets all requirements of the U.S. Department of Transportation (DOT), Canadian Council of Motor Transport Administrators (CCMTA) and Commercial Vehicle Safety Alliance (CVSA). 4 inline strap assemblies come standard with a fixed end. d in shrink wrapped plastic with a circle card. VIron Strap Assembly CC4527 Length (Feet) 27 Working Load Limit LBS KGS 5,000 2, / ctn CC ,000 2, / ctn CC4560 Design factor 3: 60 5,000 2,26 Ratchet Strap Assembly with Flat Hooks CC4730 Length (Feet) 30 Working Load Limit LBS KGS 5, , / ctn 4 / ctn Strap Assemblies Design factor 3: 4 Fixed End with Flat Hook CC473 Length Working Load Limit LBS KGS 5,000 2, / ctn Design factor 3: RollOff Container Hook Strap Assembly Government regulations require that all rollon/rolloff containers use a securement device. SCCʼs bolton hook assembly allows for easy strap replacement. CC4605 Description (Width x length) 4 x 5 Working Load Limit LBS KGS 5,000 2, / ctn Design factor 3: Container TieDown Replacement Strap CC466 Description (Width x length) 4 x 5 Working Load Limit LBS KGS 5,000 2,26.00 / ctn Design factor 3: WARNING: Never exceed Working Load Limit as stated in catalog and on strap tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233, CCMTA and the C.V.S.A inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 35

36 CARGO CONTROL 2 Interior Van Straps SCC interior van straps are designed for use inside van trailers equipped with wood or metal rails and ESeries /FSeries track. When used properly they will secure most loads from shifting or falling. All van straps come standard with a 4ʼ fixed end and a captivated adjustable end. d in shrink wrapped plastic with circle card. Interior van straps are color coded by length: 6 20 Interior Van Strap Cam Buckle with Spring E Clip Strap Assemblies CC37 CC376 CC3720 Design factor 3: Description (Length) (Color) 6 20 Working Load Limit LBS KGS / ctn / ctn / ctn Interior Van Strap Ratchet with Spring E Clip CC3 Description (Length) (Color) Working Load Limit LBS KGS, / ctn CC36 6, / ctn CC320 20, / ctn Design factor 3: Interior Van Strap Ratchet with F Track Hook CC362 Description (Length) (Color) Working Load Limit LBS KGS / ctn CC / ctn CC / ctn Design factor 3: WARNING: Never exceed Working Load Limit as stated in catalog and on strap tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233, CCMTA and the C.V.S.A inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

37 CARGO CONTROL 2 Interior Van Straps & ETrack SCC interior van straps are designed for use inside van trailers equipped with wood or metal rails and ESeries /FSeries track. When used properly they will secure most loads from shifting or falling. All van straps come standard with a 4ʼ fixed end and a captivated adjustable end. d in shrink wrapped plastic with circle card. Interior van straps are color coded by length: SCC BoardClamp with ratchet The fast and efficient interior van strap for trailers with wood or metal rails. Grips rails or boards with a thickness range of /3 /4. The exclusive cinch clamping action creates more tension when stress is applied to the strap. Rubber contact surfaces provide excellent grip. Patent# 7,54,76 B CC32 CC36 CC30 Description (Length) (Color) 6 20 Working Load Limit LBS KGS, ,000, / ctn 4 / ctn 4 / ctn Strap Assemblies Design factor 3: ETrack Rope Tie with EClip CC3703 Length: 6 Color: Multi : 0.50 Lbs. / each Working Load Limit:,000 Lbs. / 454 kgs. : / ctn Design factor 3: Constructed of high strength gauge steel with a minimum yield strength of 50,000 lbs. Yield strength is the stress at which permanent deformation takes place. Illustration measurements are shown in millimeters. BoardClamp CC250 : 2.75 Lbs. / each Working Load Limit:,000 Lbs. / 454 Kgs. : / ctn Design factor 3: Horizontal Vertical Direction Length (Feet) Finish / Color CC5600 Horizontal 5 Green paint.05 0 / pallet CC560 Horizontal 5 Zinc plated.05 0 / pallet CC5605 Horizontal Green paint / pallet CC5606 Horizontal Zinc plated / pallet CC56 Vertical 5 Green paint / pallet CC56 Vertical 5 Zinc plated / pallet CC565 Vertical Green paint.50 0 / pallet CC566 Vertical Zinc plated.50 0 / pallet WARNING: Never exceed Working Load Limit as stated in catalog and on strap tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233, CCMTA and the C.V.S.A inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 37

38 CARGO CONTROL Gunwale & Transom Tiedown Straps Marine Products 2 wide premium grade nylon webbing with an easy to use overcenter buckle and chrome finish on both the buckle and the heavy duty S hooks. The chrome finish on the hardware not only resists rust but looks great. Gunwale straps are used to secure a boat to the trailer by crossing the top of the boat over the gunnels. Transom straps are used to secure the rear of a boat to the trailer. Length (Feet) Description Working Load Limit (Lbs) CC7 Gunwale tiedown strap assembly with Shooks,0.50 / ctn Marine Products CC76 CC720 CC734 CC736 Design factor 3: Gunwale tiedown strap assembly with Shooks Gunwale tiedown strap assembly with Shooks Transom strap w/ SHooks (pair) Transom strap w/ SHooks (pair),0,0,0,0.50 / ctn.65 / ctn.40 pr / ctn.50 pr / ctn Boat Trailer Winches Hand operated winches for boat trailers with either galvanized aircraft cable or webbing and a latch hook. The winches and hooks are zinc plated to protect from rusting. They have a 4.: gear ratio for easier cranking. Length (Feet) Description Working Load Limit (Lbs) Type Gear Ratio CC Hand winch w/ galvanized 3/6 cable & hook,200 2 way / speed 4.:.00 6 / ctn CC Hand winch w/ 2 web strap & hook,200 2 way / speed 4.:.00 6 / ctn Design factor.5: Replacement Strap for Boat Trailer Winch This replacement strap is made from 2 wide premium grade nylon webbing and chrome finished hardware to resist rust and look great. Design factor 3: Length (Feet) CC70 30 Description 2 Winch strap w/ latch hook Working Load Limit (Lbs), / ctn WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, strap assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting. 3 Minimum order quantity: package Catalog weights are approximate

39 CARGO CONTROL Bulk Strap Hardware Standard Ratchet CC Working Load Limit: 500 Lbs/227 Kgs Each: 0.50 Lbs. Finish: Yellow zinc : 0 Design Factor: 3: Extra Heavy Duty Ratchet CC Working Load Limit:,0 Lbs/500 Kgs Each: 0.75Lbs. Finish: Yellow zinc : 40 Design Factor: 3: Chrome Ratchet CC50 Working Load Limit: 500 Lbs/227 Kgs Each: 0.50 Lbs. Finish: Chrome : 0 Design Factor: 3: Stainless Wide Handle Ratchet CC25 Working Load Limit:,0 Lbs/500 Kgs Each: 0.0 Lbs. Finish: Stainless Steel : 40 Design Factor: 3: Strap Hardware 2 Short Wide Ratchet CC2 Working Load Limit: 3,670 Lbs/,665 Kgs Each: 2.35 Lbs. Finish: Yellow zinc : 20 Design Factor: 3: 2 Standard Ratchet CC22 Working Load Limit: 3,670 Lbs/,665 Kgs Each: 2.2 Lbs. Finish: Yellow zinc : 20 Design Factor: 3: 2 Light Duty Ratchet Finish: Yellow zinc CC2 Working Load Limit:,500 Lbs/60 Kgs Each:.30 Lbs. : 0 Design Factor: 3: 2 Extra Long Wide Ratchet CC2 Working Load Limit: 3,670 Lbs/,665 Kgs Each: 2.45 Lbs. Finish: Yellow zinc : 20 Design Factor: 3: WARNING: Failure to understand these instructions could cause serious personal injury or loss of life. Never exceed the working load limit of a strap or fitting. It is the users responsibility to determine the suitablility of an item prior to use. Use of these items demonstrates an understanding of their uses, limitations, these warnings and the risks involved. All strap assemblies are only as strong as their weakest point including the point of attachment. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 3

40 CARGO CONTROL Bulk Strap Hardware 2 Stainless Short Wide Ratchet CC220 Working Load Limit: 2,200 Lbs/,000 Kgs Each: 2.2 Lbs. Finish: Stainless Steel : 20 Design Factor: 3: 2 Stainless Light Duty Wide Handle Ratchet CC220 Working Load Limit:,466 Lbs/665 Kgs Each:.5 Lbs. Finish: Stainless Steel : 40 Design Factor: 3: Strap Hardware 3 Standard Ratchet Finish: Yellow zinc CC3000 Working Load Limit: 5,600 Lbs/2,540 Kgs Each: 7.40 Lbs. : 5 Design Factor: 3: 4 Standard Ratchet CC4000 Working Load Limit: 6,00 Lbs/3,05 Kgs Each:.70 Lbs. Finish: Yellow zinc : 5 Design Factor: 3:.75 Over Center Buckle CC750 Working Load Limit:,50 Lbs/520 Kgs Each: 0.45 Lbs. Finish: Chrome : 0 Design Factor: 3: 2 Stamped Flat DRing CC27 Working Load Limit: 3,333 Lbs/,5 Kgs Each: 0.2 Lbs. Finish: Yellow zinc : 200 Design Factor: 3: 3 Forged VIron (Dring) CC3 Working Load Limit: 5,400 Lbs/2,450 Kgs Each: 0.3 Lbs. Finish: Bright zinc : 60 Design Factor: 3: 4 Forged VIron (Dring) CC4 Working Load Limit: 6,670 Lbs/3,025 Kgs Each:.5 Lbs. Finish: Bright zinc : 50 Design Factor: 3: WARNING: Failure to understand these instructions could cause serious personal injury or loss of life. Never exceed the working load limit of a strap or fitting. It is the users responsibility to determine the suitablility of an item prior to use. Use of these items demonstrates an understanding of their uses, limitations, these warnings and the risks involved. All strap assemblies are only as strong as their weakest point including the point of attachment. These products are NOT designed or approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

41 CARGO CONTROL Bulk Strap Hardware Extra Heavy Duty Cam Buckle CC5 Working Load Limit: 500 Lbs/225 Kgs Each: 0.2 Lbs. Finish: Zinc : 200 Design Factor: 3: Light Duty Cam Buckle CC Working Load Limit: 200 Lbs/0 Kgs Each: 0. Lbs. Finish: Zinc : 500 Design Factor: 3: Over Center Buckle CC Working Load Limit: 660 Lbs/300 Kgs Each: 0.34 Lbs. Finish: Bright zinc : 0 Design Factor: 3: 2 Cam Buckle CC26 Working Load Limit: 35 Lbs/30 Kgs Each: 0.55 Lbs. Finish: Zinc : 0 Design Factor: 3: Strap Hardware 2 Over Center Buckle CC2 Working Load Limit:,0 Lbs/500 Kgs Each: 0.6 Lbs. Finish: Bright zinc : 60 Design Factor: 3: 2 Stainless Over Center Buckle CC2250 Working Load Limit:,000 Lbs/455 Kgs Each: 0.70 Lbs. Finish: Stainless Steel : 60 Design Factor: 3: Flat Hook 2 Narrow Flat Hook CC6 Working Load Limit: 220 Lbs/0 Kgs Each: 0.07 Lbs. Finish: Black PVC : 500 Design Factor: 3: CC27 Working Load Limit: 2,200 Lbs/,000 Kgs Each: 0.66 Lbs. Finish: Yellow zinc : 0 Design Factor: 3: WARNING: Failure to understand these instructions could cause serious personal injury or loss of life. Never exceed the working load limit of a strap or fitting. It is the users responsibility to determine the suitablility of an item prior to use. Use of these items demonstrates an understanding of their uses, limitations, these warnings and the risks involved. All strap assemblies are only as strong as their weakest point including the point of attachment. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 4

42 CARGO CONTROL Bulk Strap Hardware 2 Flat Hook (w/ wear clip) CC23 Working Load Limit: 3,335 Lbs/,53 Kgs Each: 0.67 Lbs. Finish: Yellow zinc : 0 Design Factor: 3: 4 Flat Hook (w/ wear clip) CC43 Working Load Limit: 5,000 Lbs/2,26 Kgs Each:.04 Lbs. Finish: Yellow zinc : 60 Design Factor: 3: Strap Hardware Double J Hook (Short) CC3 Working Load Limit: 35 Lbs/37 Kgs Each: 0.6 Lbs. Finish: Yellow zinc : 500 Design Factor: 3: Double J Hook (Long) CC3 Working Load Limit:,0 Lbs/500 Kgs Each: 0.25 Lbs. Finish: Yellow zinc : 300 Design Factor: 3: 2 Double J Hook CC25 Working Load Limit: 3,670 Lbs/,664 Kgs Each: 0.7 Lbs. Finish: Yellow zinc : 0 Design Factor: 3: 3 Double J Hook CC35 Working Load Limit: 7,333 Lbs/3,326 Kgs Each:.50 Lbs. Finish: Yellow zinc : 40 Design Factor: 3: SHook (mm) CC4 Working Load Limit: 500 Lbs/227 Kgs Each: 0.20 Lbs. Finish: Yellow zinc : 200 Design Factor: 3: Vinyl Coated SHook (mm) CC6 Working Load Limit: 500 Lbs/227 Kgs Each: 0.22 Lbs. Finish: Black PVC : 200 Design Factor: 3: WARNING: Failure to understand these instructions could cause serious personal injury or loss of life. Never exceed the working load limit of a strap or fitting. It is the users responsibility to determine the suitablility of an item prior to use. Use of these items demonstrates an understanding of their uses, limitations, these warnings and the risks involved. All strap assemblies are only as strong as their weakest point including the point of attachment. These products are NOT designed or approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

43 CARGO CONTROL Bulk Strap Hardware Chrome SHook (mm) CC54 Working Load Limit: 500 Lbs/227 Kgs Each: 0.5 Lbs. Finish: Chrome : 0 Design Factor: 3: SHook (mm) CC5 Working Load Limit: 33 Lbs/337 Kgs Each: 0.3 Lbs. Finish: Yellow zinc : 50 Design Factor: 3: Vinyl Coated SHook (mm) CC7 Working Load Limit: 33 Lbs/377 Kgs Each: 0.3 Lbs. Finish: Black PVC : 50 Design Factor: 3: Chrome SHook (mm) CC52 Working Load Limit:,0 Lbs/500 Kgs Each: 0.44 Lbs. Finish: Chrome : 0 Design Factor: 3: Strap Hardware SHook (mm) CC0 Working Load Limit:,0 Lbs/500 Kgs Each: 0.3 Lbs. Finish: Yellow zinc : 0 Design Factor: 3: Vinyl Coated SHook (mm) CC2 Working Load Limit:,0 Lbs/500 Kgs Each: 0.42 Lbs. Finish: Black PVC : 0 Design Factor: 3: Stainless Steel SHook (mm) CC60 Working Load Limit: 500 Lbs/227 Kgs Each: 0.0 Lbs. Finish: Stainless Steel : 0 Design Factor: 3: 2 Spring EClip (for E & A track) CC24 Working Load Limit:,500 Lbs/60 Kgs Each: 0. Lbs. Finish: Yellow zinc : 250 Design Factor: 3: WARNING: Failure to understand these instructions could cause serious personal injury or loss of life. Never exceed the working load limit of a strap or fitting. It is the users responsibility to determine the suitablility of an item prior to use. Use of these items demonstrates an understanding of their uses, limitations, these warnings and the risks involved. All strap assemblies are only as strong as their weakest point including the point of attachment. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 43

44 CARGO CONTROL Bulk Strap Hardware 2 FTrack Hook CC25 Working Load Limit: 735 Lbs/335 Kgs Each: 0. Lbs. Finish: Yellow zinc : 250 Design Factor: 3: Heavy Duty DRing CC Working Load Limit:,670 Lbs/757 Kgs Each: 0.07 Lbs. Finish: Yellow zinc : 700 Design Factor: 3: Strap Hardware 2 Wire Formed DRing CC2 Working Load Limit:,670 Lbs/757 Kgs Each: 0.2 Lbs. Finish: Yellow zinc : 300 Design Factor: 3: 2 Snap Hook CC23 Working Load Limit: 2,000 Lbs/07 Kgs Each: 0.37 Lbs. Finish: Yellow zinc : 0 Design Factor: 3: 2 Heavy Duty Snap Hook CC23 Working Load Limit: 3,666 Lbs/,662 Kgs Each: 0.60 Lbs. Finish: Yellow zinc : 0 Design Factor: 3: 2 Flat Snap Hook CC2 Working Load Limit: 3,666 Lbs/,662 Kgs Each: 0.70 Lbs. Finish: Yellow zinc : 50 Design Factor: 3: 2 Twist Snap Hook CC2 Working Load Limit: 3,666 Lbs/,662 kgs Each: 0.5 Lbs. Finish: Yellow zinc : 60 Design Factor: 3: 4 Rolloff Container Hook CC425 Working Load Limit: 5,000 Lbs/2,26 Kgs Each: 4.50 Lbs. Finish: Black : 20 Design Factor: 3: WARNING: Failure to understand these instructions could cause serious personal injury or loss of life. Never exceed the working load limit of a strap or fitting. It is the users responsibility to determine the suitablility of an item prior to use. Use of these items demonstrates an understanding of their uses, limitations, these warnings and the risks involved. All strap assemblies are only as strong as their weakest point including the point of attachment. These products are NOT designed or approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

45 CARGO CONTROL Bulk Strap Hardware RTJ Cluster Hook (3 link for chain) CC230 Working Load Limit: 4,000 Lbs/,5 Kgs Each: 2.65 Lbs. Finish: Bright zinc : Design Factor: 3: RTJ Cluster Hook ( link for web) CC232 Working Load Limit: 4,000 Lbs/,5 Kgs Each: 2.2 Lbs. Finish: Bright zinc : Design Factor: 3: 5/6 Eye Grab Hook (w/ Pear link) CC3 Working Load Limit: 3,00 Lbs/,770 Kgs Each:.00 Lbs. Finish: Bright zinc : 50 Design Factor: 3: Eye Grab Hook (w/ Pear link) CC32 Working Load Limit: 5,400 Lbs/2,450 Kgs Each:.45 Lbs. Finish: Bright zinc : 50 Design Factor: 3: Strap Hardware 5/6 x HT Chain (w/ Pear & Grab hook) CC3 Working Load Limit: 3,00 Lbs/,770 Kgs Each: 2. Lbs. Finish: Bright zinc : 50 Design Factor: 3: x HT Chain (w/ Pear & Grab hook) CC4 Working Load Limit: 5,400 Lbs/2,450 Kgs Each: 3.3 Lbs. Finish: Bright zinc : 50 Design Factor: 3: x HT Chain (w/ 3 V & Grab hook) CC4V3 Working Load Limit: 5,400 Lbs/2,450 Kgs Each: 3. Lbs. Finish: Bright zinc : 50 Design Factor: 3: x HT Chain (w/ 4 V & Grab hook) CC4V4 Working Load Limit: 5,400 Lbs/2,450 Kgs Each: 3.30 Lbs. Finish: Bright zinc : 50 Design Factor: 3: WARNING: Failure to understand these instructions could cause serious personal injury or loss of life. Never exceed the working load limit of a strap or fitting. It is the users responsibility to determine the suitablility of an item prior to use. Use of these items demonstrates an understanding of their uses, limitations, these warnings and the risks involved. All strap assemblies are only as strong as their weakest point including the point of attachment. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 45

46 CARGO CONTROL Winches All SCC winches, when installed properly, provide for a safe and secure method of cargo tiedown on flat bed style trailers. They are made from medium carbon steel and meet all requirements of the DOT, CVSA and the CCMTA. For use with 2, 3 & 4 webbing and cable. Standard Bottom Mount WeldOn Web Winch CC550 Working Load Limit: 5,000 Lbs/2,270 Kgs Each:.50 Lbs. Finish: Black powdercoat : 6 Design Factor: 3: Combination Bottom Mount WeldOn Web & Cable Winch CC554 Working Load Limit: 5,000 Lbs/2,270 Kgs Each:.30 Lbs. Finish: Black powdercoat : 6 Design Factor: 3: Winches Standard LowProfile SIde Mount WeldOn Web Winch CC560 Working Load Limit: 5,000 Lbs/2,270 Kgs Each:.00 Lbs. Finish: Black powdercoat : 6 Design Factor: 3: Combination Low Profile Side Mount WeldOn Web & Cable Winch CC564 Working Load Limit: 5,000 Lbs/2,270 Kgs Each:.5 Lbs. Finish: Black powdercoat : 6 Design Factor: 3: Standard Slider Winch CC500 Working Load Limit: 5,000 Lbs/2,270 Kgs Each:.35 Lbs. Finish: Black powdercoat : 6 Design Factor: 3: Storable Slider Winch CC506 Working Load Limit: 5,000 Lbs/2,270 Kgs Each:.50 Lbs. Finish: Black powdercoat : 6 Design Factor: 3: WARNING: Mount and position the winch so that the latch/pawl drops into the gear sprocket teeth by its own weight. For weldon type winches, a continuous /4 fillet weld, 4 long on both sides of the winch frame with / minimum penetration is required. (Use a filler wire compatible with ANSI 5 steel.) Portable and slider winches must be positioned not to interfere with any other trailer components (i.e., tire clearance). Set screws on portable winches should be snug tightened only. Over tightening can cause bracket to bend or break, resulting in possible failure and loss of tiedown. Portable winches must be removed from trailer and stored when not in use. WARNING: Failure to comply with these instructions may result in property damage, serious personal injury and/or loss of life. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handles, bars and other binding equipment as it could release without warning and with extreme force. Use of these products demonstrates an understanding of these warnings and the risks involved. Use extreme caution when tensioning the winch/assembly to assure the latch pawl is fully engaged in the gear sprocket teeth before releasing the pressure on the winch bar. Always keep hands and fingers away from the winch pawl & keep face, head and body out of the path of the winch bar Minimum order quantity: package Catalog weights are approximate

47 CARGO CONTROL Winches All SCC winches, when installed properly, provide for a safe and secure method of cargo tiedown on flat bed style trailers. They are made from medium carbon steel and meet all requirements of the DOT, CVSA and the CCMTA. For use with 2, 3 & 4 webbing and cable. Standard Bottom Mount Portable Web Winch (with 2 bolts) CC555 Working Load Limit: 5,000 Lbs/2,270 Kgs Each:.5 Lbs. Finish: Black powdercoat : 6 Design Factor: 3: LowProfile Side Mount Portable Web Winch (with 2 bolts) CC565 Working Load Limit: 5,000 Lbs/2,270 Kgs Each:.50 Lbs. See important warnings on Pg. 25 Finish: Black powdercoat : 6 Design Factor: 3: Winches Lashing winches, for use with 2 webbing, can be welded or bolted onto a trailer. Winch design offers similar features of a ratchet buckle with its quick release. Hex drive style requires a / hex head wrench or socket. Lashing Winch Hex Drive CC520 Working Load Limit: 3,335 Lbs/,55 Kgs Each: 3.55 Lbs. Finish: Black powdercoat : Design Factor: 3: Lashing Winch Standar Bar Drive CC522 Working Load Limit: 3,335 Lbs/,55 Kgs Each: 3. Lbs. Finish: Black powdercoat : Design Factor: 3: FOR PROPER PROPER WINCH WINCH USE: USE: Use extreme caution when tensioning the winch/assembly to assure the latch/pawl is fully engaged in the gear sprocket teeth before releasing the pressure on the winch bar. Always keep hands and fingers away from the winch pawl & keep face, head and body out of path of winch bar. Inspect all binding components (winch, strap assembly, chain assembly, loadbinder) prior to each use. Never use damaged or worn equipment. Remove from service and replace with new. Do not attempt to repair. Winch bars are used entirely at the users own risk and the use of a winch bar demonstrates an understanding of the risks and a willingness to accept the consequences of possible property damage, serious personal injury and/or loss of life. When using SCC winch bars with winches: the tapered point of the bar must be inserted completely through both holes in the winch cap. Failure to insert bar correctly could cause the bar to slip and result in serious personal injury and/or loss of life. During tightening and before releasing the tie down assembly, check the winch pawl to insure it has properly engaged the gear sprocket. Always grip the winch bar at the knurled section of the bar for increased safety. WARNING: Mount and position the winch so that the latch/pawl drops into the gear sprocket teeth by its own weight. For weldon type winches, a continuous /4 fillet weld, 4 long on both sides of the winch frame with / minimum penetration is required. (Use a filler wire compatible with ANSI 5 steel.) Portable and slider winches must be positioned not to interfere with any other trailer components (i.e., tire clearance). Set screws on portable winches should be snug tightened only. Over tightening can cause bracket to bend or break, resulting in possible failure and loss of tiedown. Portable winches must be removed from trailer and stored when not in use. WARNING: Failure to comply with these instructions may result in property damage, serious personal injury and/or loss of life. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handles, bars and other binding equipment as it could release without warning and with extreme force. Use of these products demonstrates an understanding of these warnings and the risks involved. Use extreme caution when tensioning the winch/assembly to assure the latch pawl is fully engaged in the gear sprocket teeth before releasing the pressure on the winch bar. Always keep hands and fingers away from the winch pawl & keep face, head and body out of the path of the winch bar. Catalog weights are approximate Minimum order quantity: package 47

48 CARGO CONTROL Winch Bars / Hard Parts / SCC CargoGuard Winch Bars Winch bars feature a knurled handle for a safe grip as well as tapered case hardened ribbed nose piece for strength and to prevent slippage. CC5505 CC5505 Description Standard winch bar Finish Painted Length / ctn CC5506 CC5506 Standard winch bar Chrome / ctn Misc. Cargo Control Products CC555 CC556 Hardware Combination winch bar Combination winch bar Painted Chrome CargoBar Rack (For square bars only) CC5620 : 6.25 Lbs. / ea. : / ctn / ctn 6. 6 / ctn WeldOn C Hook CC5626 : 0.3 Lbs. / ea. : / ctn CC555 CC556 4 Metal Corner CC5630 : 0.67 Lbs. / ea. : 24 / ctn 4 Rubber Corner CC5634 : 0. Lbs. / ea. : 50 / ctn 6 Galvanized Corner CC5635 :.3 Lbs. / ea. : 24 / ctn HD Beam Socket CC5642 : 0.2 Lbs. / ea. : / ctn G70 Floor Chain Anchor ( Chain) CC5656 : 3.45 Lbs. / ea. : / ctn 4 Plastic Corner CC560 : 0.30 Lbs. / ea. : 24 / ctn Strap Winder CC565 : 3.7 Lbs. / ea. : 6 / ctn SCC CargoGuard Flexible Corner Protectors The SCC CargoGuard features patented, multiple living hinges that adapt to the form of any cargo, regardless of the shape. It is designed to protect both the strap and the cargo and can be installed even after the strap has been placed on the load. Made from high impact thermoplastic, 2 or more snap together for any required length. They can be neatly stacked and are available for both 2 and 4 straps. CargoGuard For 2 straps CC56 : 0.07 Lbs. / ea. : 24 / ctn CargoGuard For 2 & 4 straps CC562 : 0. Lbs. / ea. : 24 / ctn CargoGuard (Retail 2 pk.) For 2 & 4 straps CC564 : 0.2 Lbs. / ea. : 24 pr./ ctn WARNING: Cheater bars or extensions should never be used with winch bars. Use extreme caution when tensioning the winch/assembly to assure the latch pawl is fully engaged in the gear sprocket teeth before releasing the pressure on the winch bar. Always keep hands and fingers away from the winch pawl & keep face, head and body out of the path of the winch bar. When using SCC winch bars with winches: the tapered point of the bar must be inserted completely through both holes in the winch cap. Failure to insert bar correctly could cause the bar to slip and result in serious personal injury and/or loss of life. 4 Minimum order quantity: package Catalog weights are approximate

49 CARGO CONTROL Rubber & Elastic TieDown Accessories Rubber Rope CC70 CC73 CC75 CC7 Size 7/6 7/6 Strap Length Core Hollow Solid Hollow Solid Rubber Tarp Straps with Hooks BULK PKG RETAIL PKG CC40 CC45 Overall Length Max. stretch Length (feet) (Lbs) / ctn / ctn / ctn / ctn Retail tarp straps are packaged 2 per poly bag with a header card. All tarp straps are UPC coded for sale. CC45 CC42 CC43 CC44 CC465 CC47 CC4 CC Hooks for Rubber & Elastic TieDown Products (Lbs) BULK PKG RETAIL PKG BULK PKG RETAIL PKG 50 / ctn pr / ctn 50 / ctn 50 / ctn 50 / ctn pr / ctn pr / ctn pr / ctn 50 / ctn pr / ctn Misc. TieDown Products Rubber Rope SJ Hook Tarp Strap S Hook CC Wire Diameter: 0.60 Inside Length: 3.0 : 0.05 Lbs. / ea. Finish: Bright zinc : 0 / ctn CC4 Wire Diameter: 0.75 Inside Length: 2.40 : 0.05 Lbs. / ea. Finish: Bright zinc : 0 / ctn Stretch Cords Retail packaged cords are packaged 2 per poly bag with a header card except for the 5mm size which is packaged 4 per poly bag. CC555 CC562 CC56 CC574 CC50 CC56 Cord Dia. (mm) 5 Overall length Maximum stretch bags per ctn bags per ctn bags per ctn bags per ctn bags per ctn bags per ctn WARNING: Failure to comply with instructions may result in property damage, serious personal injury or death. Rubber and elastic items store energy which can release suddenly, causing serious injury. Stay clear of stretchable items when installing and at all times when tension is applied. This energy could release without warning and with force. Eye protection is recommended at all times. These items are not designed for cargo restraint or tiedown. They are only designed to hold tarp covers in place. Do not use if product shows cuts, cracks, fraying or if hooks are bent or damaged. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 4

50 CARGO CONTROL Trailer Safety Chain SCCʼS trailer safety chains are designed to keep a trailer connected to a vehicle if the hitch fails or comes uncoupled. They feature heat treated, medium carbon steel Shooks, with or without safety latches. All trailer safety chains and trailer safety chain SHooks have a bright zinc finish. HOW TO CHOOSE THE CORRECT SAFETY CHAIN TO HANDLE THE LOAD: CLASS DESIGNATION: CLASS I CLASS II CLASS III CLASS IV Maximum Load Capacity: Up to 2,000 lbs gross trailer wt. Up to 200 lbs gross tongue wt. Up to 3,500 lbs gross trailer wt. Up to 300 lbs gross tongue wt. Up to 5,000 lbs gross trailer wt. Up to 500 lbs gross tongue wt. Up to,000 lbs gross trailer wt. Up to,000 lbs gross tongue wt. Towing Products 4 S3 Trailer Safety Chain with Two S Hooks H23603 Trade size 3/6 Length 4 Trailer class I Hook size.7 Working Load Limit LBS KGS / Half drum H23604 /4 4 II 7/6 3., / Half drum H /6 4 III 7/ , / Half drum Design factor 3: 4 S3 Trailer Safety Chain with Two Safety Latch S Hooks Meets California towing requirements H2703 Trade size 3/6 Length 4 Trailer class I Hook size 2.00 Working Load Limit LBS KGS / Half drum H2704 /4 4 II 7/6 3.30, / Half drum H2705 5/6 4 III 7/ , / Half drum Design factor 3: 54 S3 Trailer Safety Chain with Two Safety Latch S Hooks Meets California towing requirements Trade size Length Trailer class Hook size Working Load Limit LBS KGS H2304 /4 54 II 7/6 3.75, / Half drum H2305 5/6 54 III 7/ , / Half drum Design factor 3: WARNING: Observe the Working Load Limit. Inspect all hooks and chain for distortion, cracks or damage prior to use. If the hook or chain is worn or distorted, remove from service immediately and replace. Never point or tip load hook. Never subject a hook or chain to shock loading or jerking. Always cross the chains under the hitch in a X pattern. These products are NOT designed or approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

51 CARGO CONTROL Trailer Safety Chain & Hooks / Auto TieDown Straps Trailer Safety Chain S Hooks (Bright zinc) Latch hooks meet California Safety Requirements WITH LATCH NO LATCH Trade size Wire Size Class Trailer WITH LATCH NO LATCH Working Load Limit LBS KGS WITH LATCH NO LATCH H62206 H I / ctn 0 / ctn H62207 H6224 Design factor 3: Design factor 4: H H62304 Trade size 7/6 7/32 Length S7 Truck Dolly Safety Chain with Latch Hook (Yellow zinc) H / Trailer class Auto TieDowns & Axle Straps II III Hook size 36 VII 5/ premium polyester, shrink wrapped for retail shelf display. Axle straps feature protective sleeves. Order unit is each ,250,00 Working Load Limit LBS KGS 5,00 7, / Half drum 50 / ctn 50 / ctn 0 / ctn 0 / ctn Towing Products & Auto TieDowns Auto TieDown w/ Ratchet, HD Snap hook & RTJ hook Auto TieDown w/ Ratchet, Snap hook & fixed D Ring CC2574 CC2575 Length: Length: Working Load Limit: 3,300 Lbs Working Load Limit: 2,000 Lbs : 6.00 Lbs. / ea. : 4.50 Lbs. / ea. : / ctn : / ctn Design factor 3: Design factor 3: Auto TieDown w/ Ratchet, HD Snap hooks & Floating D Ring CC2576 Length: Working Load Limit: 3,300 Lbs : 5.00 Lbs. / ea. : / ctn Design factor 3: Axle Strap w/ HD Snap Hooks & Floating D Ring Axel Strap w/ 2 D Rings CC257 Length: 3 Working Load Limit: 3,300 Lbs :.00 Lbs. / ea. : / ctn Design factor 3: Auto TieDown Kit w/ Carrying Case CC257 Length: 4 Working Load Limit: 3,300 Lbs :.2 Lbs. / ea. : / ctn Design factor 3: CC2570 Includes: 2 ea. CC2576 & CC257 Working Load Limit: 3,300 Lbs : 5.50 Lbs. / ea. : 4 kits / ctn Design factor 3: WARNING: Observe the Working Load Limit. Inspect all hooks and chain for distortion, cracks or damage prior to use. If the hook or chain is worn or distorted, remove from service immediately and replace. Never point or tip load hook. Never subject a hook or chain to shock loading or jerking. Always cross the chains under the hitch in a X pattern. These products are NOT designed or approved for overhead lifting. WARNING: Failure to comply with instructions may result in property damage, serious personal injury or death. These items store energy which can release suddenly, causing serious injury. Stay clear of equipment path when installing and at all times when tension is applied. This energy could release without warning and with force. Catalog weights are approximate Minimum order quantity: package 5

52 CARGO CONTROL Tow Chains / Tow Straps / Cable Pullers G70 Tow Chain with Two Clevis Grab Hooks NOT Approved For Overhead Lifting Tow chains are packaged in a rugged plastic box for convenient storage. These chains have high quality drop forged clevis grab hooks. Yellow zinc finish. H34550 Chain Diameter 5/6 Length (Feet) 6 Working Load Limit LBS KGS 4,700 2, / ctn Towing Products & Cable Pullers H Design factor 4: Tow Straps Premium nylon tow straps are packaged in shrink wrap plastic with circle card. Tow straps with hook features 2 chrome eye tow hooks. CC200 End Type Hooks Width 2 6 Length (Feet) 20 6,600 2,4 Working Load Limit LBS KGS 5,000 2, / ctn / ctn NOT Approved For Overhead Lifting CC2002 Loop ,000 2, / ctn CC2003 Loop ,000 2, / ctn CC2004 Loop ,00 3, / ctn CC2005 Loop 4 30,000 4, / ctn Design factor 3: Cable Pullers NOT Approved For Overhead Lifting 2 Ton Cable Puller HT4502 Cable size: 3/6 Travel: 6 Shipping : 6.70 Lbs : 6 / ctn 4 Ton Cable Puller HT4504 Cable size: /4 Travel: 6 Shipping :.75 Lbs : 4 / ctn WARNING: Failure to comply with instructions may result in property damage, serious personal injury or death. These items store energy which can release suddenly, causing serious injury. Stay clear of equipment path when installing and at all times when tension is applied. This energy could release without warning and with force. Do not use if product shows cuts, cracks, gouges, fraying, if hooks are bent or damaged, or if links are elongated. When using a chain or strap assembly for towing a vehicle, always be sure that the chain/strap is attached to a secure part on both vehicles capable of withstanding the load being applied. Be sure to keep them away from loosely attached parts or vehicle parts that could be damaged by the assembly (oil pans, bumpers, grill, etc.) or parts of the vehicle that could melt the strap (manifolds, exhaust pipes). If attachments are used, such as shackles, to connect the chain/strap, extreme care should be taken to assure that these attachments are of sufficient strength to withstand the load being applied. Consult the owners manual for proper attaching and towing procedures. Remember, all assemblies are only as strong as the weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting. WARNING: Failure to comply with instructions may result in property damage, serious personal injury or death. Use of these products demonstrates an understanding of these warnings/instructions and the risks involved. Cable pullers are not designed for overhead lifting. DO NOT lift any material above waist height. Keep all persons clear of load while suspended. Never allow persons beneath a suspended load. Cable pullers are not designed for cargo tiedown or load securement. They are not approved for use as such by any government agency. Do not load in excess of rated capacity. Inspect puller and components prior to each use. Do not use if any part of the cable puller is visibly damaged. Never use handle extensions (cheater bars). Do not use puller around sharp corners as this may damage the cable, greatly reducing its strength. Never tip load hooks. Do not use if the cable is kinked or knotted Minimum order quantity: package Catalog weights are approximate

53 CARGO CONTROL SCC SmartBar The most versatile loadlock on the market U.S. Patent #6,755,600 B2 & 7,334,73 SCCʼs SmartBar, with high leverage and flexible feet, mean superior holding power. Square vs. round tubing provides a stronger bar (less susceptible to bending and more surface area to cargo). SCCʼs SmartBar can brace a whole load or just part of one. Easier to use and store. 40 SCC SmartBars can ship on a standard pallet Up to 20% more holding power than conventional loadlocks. Adjusts continuously from 4. Securement range from small truck bed to full high cube trailer width. The vinyl coated lever provides smooth, positive operation. Closed bar locking tab is easily locked / unlocked with the convenient thumb release. The SCC SmartBar is designed for use in trailers with flexible walls. The feet have extra cushioning to compensate for the flex of some trailers. Cargo Bars With optional ETrack attachment (#CC505), the SCC SmartBar can easily be adapted for use in A & E track, doubling the front to back holding power. SCC SmartBar Description Finish Reach CC50 3 section steel SmartBar Zinc plated / bundle SCC SmartBar Parts ETrack Kit (For CC50) CC505 : 0. Lbs. / ea. : kits / ctn Repair Kit (For CC50) CC506 : 0.6 Lbs. / ea. : kits / ctn Replacement Foot Small (For CC50) CC50 : 0.40 Lbs. / ea. : / ctn Replacement Foot Large (For CC50) CC50 : 0.45 Lbs. / ea. : / ctn WARNING: Failure to understand and comply with these instructions and warning may result in property damage, serious personal injury or death. Use of these products demonstrates an understanding of these warnings/instructions and the risks involved. Do not use bars to support ANY vertical loads. SCC SmartBars M and loadlocks are NOT designed to be used as a shoring beam. Using these bars as a step is not advised and could result in serious personal injury. Cargo bars and loadlocks are not designed to secure cargo inside a trailer, only to assist in the stability of a load. SCC SmartBars TM and loadlocks are designed to push out approximately one inch against flexible van trailer walls and can be damaged if used against immovable objects such as door frames. To avoid damaging the bars and trailer, never use more than one hand to close the lever. On the SCC SmartBar TM push handle release button when fully retracted to extend. A stop keeps the bar from sliding open when fully retracted and must be released before operating the lever or the bar can be damaged. To disengage lock, push on handle release tab. Catalog weights are approximate Minimum order quantity: package 53

54 CARGO CONTROL SCC SecureBar & SCC GrabBar A versatile loadlock for light truck & passenger vehicles Durable square tubing provides added strength. It is versatile and can be used in pickups, SUVs, vans and passenger cars. The soft rubber feet provide excellent grip and wonʼt mar surfaces. Retail package is a 46 four color card with pictures and instructions for use. Hangs vertical or horizontal on standard peg hooks. Adjusts continuously from 44 to 7. Easy operation Positive locking lever action and quick thumb release. Zinc plated for maximum rust protection. SCC SecureBar (U.S. Patent Pending) Cargo Bars Description Finish Reach CC5225 SCC SecureBar CargoBar Retail d Zinc plated / ctn CC5225B SCC SecureBar CargoBar Bulk d Zinc plated / crate SCC GrabBar Designed for cargo stabilization inside trailers with wood or metal rails. Feet adjust to board/rail thickness ranging from /3 3/4. Collapses down to 46 for easy storage, with a full adjustment range to 6. The rubber feet provide excellent grip and will not damage surfaces. Use the GrabBar stop collar for rigidity in stake side truck applications. SCCʼs GrabBar can also be used in conjuction with SCCʼs SmartBar (see photo at right). Description Finish Reach CC5200 SCC GrabBar Zinc plated / bundle SCC SecureBar & SCC GrabBar Parts Replacement Foot Small (For CC5225) CC523 : 0.42 Lbs. / ea. : / ctn Replacement Foot Large (For CC5225) CC523 : 0.42 Lbs. / ea. : / ctn SCC GrabBar Stop Collar (For use with CC5200) CC52 :.00 Lbs. / ea. : 6 / ctn WARNING: Failure to understand and comply with these instructions and warning may result in property damage, serious personal injury or death. Use of these products demonstrates an understanding of these warnings/instructions and the risks involved. Do not use bars to support ANY vertical Loads. SCC CargoBars M and loadlocks are NOT designed to be used as a shoring beam. Using these bars as a step is not advised and could result in serious personal injury. Cargo bars and loadlocks are not designed to secure cargo inside a trailer, only to assist in the stability of a load. SCC CargoBars TM and loadlocks are designed to push out approximately one inch against flexible van trailer walls and can be damaged if used against immovable objects such as door frames. To avoid damaging the bars and trailer, never use more than one hand to close the lever. On the SCC CargoBar TM push handle release button when fully retracted to extend. A stop keeps the bar from sliding open when fully retracted and must be released before operating the lever or the bar can be damaged. To disengage lock, push on handle release tab Minimum order quantity: package Catalog weights are approximate

55 CARGO CONTROL Loadlocks / Loadlock Parts / Coil Racks Loadlocks Piece Steel Loadlock 2 Piece Aluminun Loadlock CC5050 CC50 Reach: 2 Reach: 2 :.0 Lbs. / ea. :.00 Lbs. / ea. : 4 / bundle : / ctn Loadlock Parts Foot Large End CC57 : 0.2 Lbs. / ea. : 6 / ctn Piece Aluminun Loadlock CC550 Reach: 2 :.50 Lbs. / ea. : 4 / bundle Foot Small End CC572 : 0.2 Lbs. / ea. : 6 / ctn Aluminum Handle Assembly w/ Lock CC573 :.50 Lbs. / ea. : 6 / ctn Loadlocks & Parts / Coil Racks Replacement Handle CC574 : 0.66 Lbs. / ea. : 6 / ctn Tooth Extenstion Rack CC575 :.20 Lbs. / ea. : 6 / ctn Coil Racks Coil racks are used to assist in stabilization of metal coils during transport. Coil Rack (Heavy duty) CC564 Gauge: 6 Color: Black : 5.25 Lbs. / ea. : 4 / ctn Coil Rack (Light duty) CC5647 Gauge: Color: Black : 5.00 Lbs. / ea. : / ctn WARNING: Failure to understand and comply with these instructions and warning may result in property damage, serious personal injury or death. Use of these products demonstrates an understanding of these warnings/instructions and the risks involved. Do not use bars to support ANY vertical Loads. SCC CargoBars M and loadlocks are NOT designed to be used as a shoring beam. Using these bars as a step is not advised and could result in serious personal injury. Cargo bars and loadlocks are not designed to secure cargo inside a trailer, only to assist in the stability of a load. SCC CargoBars TM and loadlocks are designed to push out approximately one inch against flexible van trailer walls and can be damaged if used against immovable objects such as door frames. To avoid damaging the bars and trailer, never use more than one hand to close the lever. On the SCC CargoBar TM push handle release button when fully retracted to extend. A stop keeps the bar from sliding open when fully retracted and must be released before operating the lever or the bar can be damaged. To disengage lock, push on handle release tab. Catalog weights are approximate Minimum order quantity: package 55

56 CARGO CONTROL SCC QuikBinder PLUS SCC QuikBinder PLUS A ratchet binder like no other NOT Approved For Overhead Lifting U.S. Patent #s: 6,45,56 B; 7,055,04 B2; 7,22,065 This premium patented ratchet binder is unlike any other binder available on the market today. Now it is better than ever, with higher working load limits designed for use with either Grade 70 (S7) Transport or Grade 0 (T) Alloy tiedown chains. Loadbinders SCCʼs QuikBinder PLUS is easier to install than standard ratchet loadbinders. The 3position pawl offers the user a choice of ratchet extension, ratchet takeup or a free spin setting for fast adjustment in either direction. A load can be secured in half the time. It is available in three sizes and features a vinyl coated barrrel for a strong, comfortable grip. The folding handle makes SCCʼs QuikBinder PLUS safer (no handle sticking out) and more convenient to use. Simply fold the handle down after the load is secure or when storing on your cab rack. Stronger, faster, safer and and more functional than standard ratchet binders. The SCC QuikBinder PLUS can be locked to the tiedown chain with a long shank padlock, making it more difficult to tamper with the binder, assembly or the load. Padlocks with programmable combinations are available from SCC. See page 0 of this catalog for more information. 3Position pawl SCC loadbinders meet all DOT/CVSA/CCMTA requirements. The special hook construction supports the load of the chain and will not bind. Loadbinders are heat treated and proof tested with forged heat treated hooks. The Working Load Limit is permanently marked on handle. SCC loadbinders feature special links with controlled flash welds. Tamper resistant SCCʼs new QuikBinder PLUS now has higher strength ratings for use with either Grade 70 (S7) Transport or Grade 0 (T) Alloy tiedown chains. Features yellow zinc plated hooks. SCC QuikBinder Plus Ratchet Loadbinder For Chain Size 5/6 or Takeup Handle length Folded Handle length Straight (Lbs. / ea.) H Working Load Limit LBS KGS 7,0 3, H5505 or / ,000 5, H5505 /2 or 5/ ,0, Design factor 4: WARNING: Failure to comply with instructions may result in property damage, serious personal injury or and/or loss of life. Loadbinding systems store energy which can release suddenly, causing serious injury. Stay clear of handles, bars and other binding equipment as it could release without warning and with extreme force. Observe the working load limit as stated in catalog and on tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233 and the CVSA vehicle inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. Use extreme caution when tensioning the binder on a chain assembly to assure the chain links are fully seated in the hook belly before releasing the pressure on the loadbinder. Always keep hands and fingers away from the chain path and keep head and body out of the path of the loadbinder handle in case of slippage or kickback. Loadbinder extensions: Only use combination winch bars designed with a binder cradle to assist in tightening a loadbinder. Insure that the loadbinder handle is fully inserted into the winch bar cradle and locked in place. Failure to do so may cause the bar to slip and result in serious personal injury and/or loss of life. Loadbinders will tighten adequately with the torque generated by hand pullover or ratcheting. Never use pipe or unapproved extensions (cheater bars) Minimum order quantity: package Catalog weights are approximate

57 CARGO CONTROL Ratchet Binders & ProLok 66 Lever Binder SCC loadbinders meet all DOT/CVSA/CCMTA requirements. Special hook construction supports the load of the chain and will not bind. Loadbinders are heat treated and proof tested with forged heat treated hooks. The Working Load Limit is permanently marked on handle. SCC loadbinders feature special links with controlled flash welds. All SCC loadbinders are painted with yellow, powdercoat enamel. Ratchet Binder Plus Loadbinder NOT Approved For Overhead Lifting SCCʼs new Ratchet Binder Plus has higher strength ratings for use with either Grade 70 (S7) Transport or Grade 0 (T) Alloy tiedown chains. This premium binder features high quality yellow zinc plated hooks. For Chain Size Takeup Handle length Working Load Limit LBS KGS (Lbs) H545 5/6 or ,0 3, H5425 H5445 Design factor 4: /2 or or /2 5/ ,000,0 5,443, Loadbinders Ratchet Loadbinder H For Chain Size G70 G43 /4 5/6 Takeup Handle length Working Load Limit LBS KGS 3,00,76 (Lbs) 4. 2 H / ,400 2, H / ,200 4, H /2 5/ ,000 5, Design factor 3.5: SCC ProLok66 (Patent pending) SCCʼs adjustable lever loadbinder features the ultimate in ease and versatility in a lever binder with the added safety of a selflocking handle. ProLok66 has a builtin knurled adjustable nut feature so the binder doesnʼt have to be repositioned on the chain (like standard lever binders) to achieve the best possible fit and perfect tension on the chain. The binder adjusts a full 2 to give the user optimum link location. No more problems getting that last extra half link hookup. The handleʼs safety latch is automatically engaged when the handle is closed. This locks the handle in the closed position until it is released. This features makes SCCʼs adjustable binder safer than standard lever binders. The convenient thumbrelease latch is easy to use and has no loose parts to misplace. Adjustable nut Safety latch ProLok66 Adjustable Lever Loadbinder For Chain Size Takeup Handle length Working Load Limit LBS KGS (Lbs) H /6 or ,600 2, Design factor 4: WARNING: Please see warnings on the previous page. Catalog weights are approximate Minimum order quantity: package 57

58 CARGO CONTROL Safety Binder & Lever Style Loadbinders SCC loadbinders meet all DOT/CVSA/CCMTA requirements. Special hook construction supports the load of the chain and will not bind. Loadbinders are heat treated and proof tested with forged heat treated hooks. The Working Load Limit is permanently marked on handle. SCC loadbinders feature special links with controlled flash welds. All SCC loadbinders are painted with yellow, powdercoat enamel. Safety Release Lever Loadbinder NOT Approved For Overhead Lifting The saftey release handle makes this loadbinder less dangerous than other lever style loadbinders on the market today. This binder design allows the user to release the binder tension without any kickback of the handle typical of a lever style binder. The center body of the binder independently rotates, free of the handle, to release the tension smoothly and easily. This eliminates the chance for injuries from the handle swinging with substantial force when released. Loadbinders For Chain Size G70 G43 H /6 Design factor 3.5: Takeup Handle length Working Load Limit LBS KGS 5,400 2,44 (Lbs).75 4 Double Swivel Lever Loadbinder H For Chain Size G70 G43 /4 Takeup 3.00 Handle length.42 Working Load Limit LBS KGS 2,600,7 (Lbs / ea.) H / ,400 2, H / ,200 4, H /2 5/ ,000 5, Design factor 3.5: Fully Forged Double Swivel Lever Loadbinder H For Chain Size G70 G43 5/6 Takeup 3.75 Handle length 5.43 Working Load Limit LBS KGS 5,400 2,44 (Lbs / ea.) * H / ,400 2, Design factor 3.5: * Nickel/Zinc (Ni/Zn) plated finish Mini Binder Mini Binder does not meet CVSA, CCMTA or DOT Regulations. Hooks are not forged. For use with chain, cable or rope. H Takeup Handle length.5.05 Working Load Limit LBS KGS (Lbs / ea.).67 Design factor 3: WARNING: Failure to comply with instructions may result in property damage, serious personal injury or and/or loss of life. Loadbinding systems store energy which can release suddenly, causing serious injury. Stay clear of handles, bars and other binding equipment as it could release without warning and with extreme force. Observe the working load limit as stated in catalog and on tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233 and the CVSA vehicle inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. Use extreme caution when tensioning the binder on a chain assembly to assure the chain links are fully seated in the hook belly before releasing the pressure on the loadbinder. Always keep hands and fingers away from the chain path and keep head and body out of the path of the loadbinder handle in case of slippage or kickback. Loadbinder extensions: Only use combination winch bars designed with a binder cradle to assist in tightening a loadbinder. Insure that the loadbinder handle is fully inserted into the winch bar cradle and locked in place. Failure to do so may cause the bar to slip and result in serious personal injury and/or loss of life. Loadbinders will tighten adequately with the torque generated by hand pullover or ratcheting. Never use pipe or unapproved extensions (cheater bars). 5 Minimum order quantity: package Catalog weights are approximate

59 CARGO CONTROL T0 Alloy Transport TieDown Chain Assemblies Also referred to as Grade 0 or Alloy chain. Made from higher grade carbon and alloy steels to provide greater tensile strength and Working Load Limits than Grade 70 (S7) chain. T0 Alloy chain assemblies come in a black lacquer finish. Meets D.O.T/CVSA/CCMTA requirements. d bulk in drums or each in retail single packs. NOT Approved For Overhead Lifting T0 Chain Assembly with Clevis Grab Hooks ASTM Spec. short link for longer life. BULK DRUM SINGLE PACK H H H H Trade Size /2 Length (Feet) Finish Black Black Black Working Load Limit LBS KGS 7,0 3,220 7,0,000 3,220 5,443 (Lbs / ea.) BULK DRUM SINGLE PACK 20 / Drum N / A 20 / Drum / ctn / Drum N / A Chain Assemblies H H /2 20 Black,000 5, / Drum / ctn Design factor 4: TIEDOWN ASSEMBLY USAGE CHART: This chart is provided as a guide to meet the basic minimum current in service requirements of the FMCSA and the DOT published Sept 27, The following table lists the minimum number of chain assemblies required to secure a load per DOT & CVSA. *This chart is only to be used as a reference. *Many factors affect the proper method of cargo securement including the length and type of the cargo to be secured. Refer to the most recent revision of The Dept. of Transportation (DOT) Title 4 regulations for more complete requirements regarding the proper methods and number of tiedowns required. SCC Chain Grade Alloy Grade 0 (S, SX, T0) Transport Grade 70 (S7, SX7, S70) High Test Grade 43 (S4, SX4, S43) Size 5/6 /2 /4 5/6 /2 /4 5/6 /2 WLL 4,500 7,0,000 3,50 4,700 6,600,300 2,600 3,00 5,400,200 20, Net weight of cargo to be secured in Lbs. 25,000 30,000 35,000 40,000 45, , FMCSA: Federal Motor Carrier Safety Admin DOT: Department of Transportation CVSA: The Commercial Vehicle Safety Alliance Proof Coil Grade 30 (S3 SX3, S30) /4 5/6 /2,300,00 2,650 4,500 Due to the low working load limits of S3 chain, SCC does not recommend using Proof Coil Chain for Transport tiedown or cargo securement. This chart is based on each tiedown secured to a trailer anchor point, traversing across or through the load and then secured to another anchor point on the trailer. If used by securing the tiedown to the trailer anchor point and attaching it directly to an article of cargo (IE: a vehicle), the quantity of tiedowns required shall be 2 times the quantity listed in the chart above. WARNING: Never exceed Working Load Limit as stated in catalog and on strap tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233, CCMTA and the C.V.S.A inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 5

60 CARGO CONTROL G70 Transport TieDown Chain Assemblies G70 chain was specifically designed for cargo securement. Also called Transport Chain and Grade 70, it averages a 20% higher load rating than High Test chain (G43). This increased strength per pound of chain saves weight and allows for easier handling and storage. G70 assemblies have a yellow zinc finish for easier identification and for protection of the chain. Meets DOT/CVSA/CCMTA requirements. d bulk in drums or each in retail single packs. NOT Approved For Overhead Lifting G70 Chain Assembly with Clevis Grab Hooks ASTM spec short link chain for longer life. Chain Assemblies Trade Size Length Working Load Limit BULK DRUM SINGLE PACK (Feet) (Lbs / ea.) BULK DRUM SINGLE PACK LBS KGS H H /6 4 4,700 2, / drum / ctn H H /6 6 4,700 2, / drum / ctn H H /6 20 4,700 2, / drum / ctn H H /6 25 4,700 2, / drum / ctn H H /6 30 4,700 2, / drum / ctn H H ,600 2, / drum / ctn H H ,600 2, / drum / ctn H H ,600 2, / drum / ctn H H ,600 2, / drum / ctn H H ,600 2, / drum / ctn H H /2 5,300 5, / drum / ctn H H /2 20,300 5, / drum / ctn Design factor 4: G70 Chain Assembly with Clevis Grab Hooks NACM spec long link chain has a longer pitch link for less weight per assembly. Pitch is the inside lengh measurement of a link. Trade Size Length (Feet) Working Load Limit LBS KGS (Lbs / ea.) H /6 20 4,700 2, / drum H ,600 2, / drum Design factor 4: WARNING: Never exceed Working Load Limit as stated in catalog and on strap tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233, CCMTA and the C.V.S.A inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

61 CARGO CONTROL G70 Transport & G43 High Test TieDown Chain Assemblies G70 chain was specifically designed for cargo securement. Also called Transport Chain and Grade 70, it averages a 20% higher load rating than High Test chain (G43). This increased strength per pound of chain saves weight and allows for easier handling and storage. G70 assemblies have a yellow zinc finish for easier identification and for protection of the chain. Meets DOT/CVSA/CCMTA requirements. d bulk in drums or each in retail single packs. G43 chain asseemblies are made from higher grade carbon steel to provide greater tensile strength and Working Load Limits than low grade Proof Coil chain. High Test chain assemblies come in a self color tumbled finish. Meets D.O.T/CVSA/CCMTA requirements. d bulk in drums or each in retail single packs. NOT Approved For Overhead Lifting G70 Chain Assembly with Eye Grab Hooks ASTM spec short link chain for longer life. Chain Assemblies Trade Size Length Working Load Limit BULK DRUM SINGLE PACK (Feet) LBS KGS (Lbs / ea.) BULK DRUM SINGLE PACK H H ,600 2, / drum / ctn H H ,600 2, / drum / ctn Design factor 4: G43 Chain Assembly with Clevis Grab Hooks ASTM spec short link chain for longer life. Trade Size Length Working Load Limit BULK DRUM SINGLE PACK (Feet) LBS KGS (Lbs / ea.) BULK DRUM SINGLE PACK H H /6 20 3,00, / drum / ctn H H ,400 2, / drum / ctn Design factor 3: WARNING: Never exceed Working Load Limit as stated in catalog and on strap tags to determine the number of tiedown assemblies and/or hardware required for safe operation per federal D.O.T. FMCSA 4 CFR Parts 3233, CCMTA and the C.V.S.A inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. Remember, assemblies are only as strong as their weakest point, including the point of attachment. These products are NOT designed or approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 6

62

63 Section 3 Hardware Welded Chain G70 Transport G43 High Test G30 Proof Coil Stainless Chain & Accessories 66 Machine Passing Link Coil... 7 Weldless Chain Double Loop Lock Link Single Jack Brass Safety Sash Plastic Chain & Accessories. 74 Chain Accessories G43 & G70 Hooks Latch Kits Double Clevis... 7 Clevis Pins... 7 Lap Link... 7 Cold Shut... 7 Quick Link... 7 Connecting Link... 0 Snap Pear Hooks... 0 SHooks... 0 Shackles Snaps Aircraft Cable Aircraft Cable Accessories... 7 AntiTheft Chain & Padlocks... 0 Tools... Cable Cutters & Swedgers.. Chain & Bolt Cutters... Ratchet & Hydraulic Cutters.. Hammers... Pallet Jacks Retail d Hardware Chain Merchandisers... 6

64 HARDWARE Grade 70 Transport Chain Grade 70 was designed specifically to provide a light, yet strong chain for binding, tiedowns, towing and construction use. Made from a variety of medium carbon and alloy materials. Induction heat treated, the chain meets all requirements set by the Department of Transportation (D.O.T.), CCMTA & C.V.S.A. for truck tiedown use. Manufactured to ASTM 0 short link specs. NOT Approved For Overhead Lifting G70 Transport Chain (Full drum) Hallmarked: SCC7, SX7 or S7 every inches YELLOW ZINC H Trade size (mm) /4 7.0 Wire dia. Inside link dimension A B Feet per drum 00 Lbs per 0/ft 75 Working load limit (Lbs.) (Kgs.) 3,50,42 H / ,700 2,32 H ,600 2,4 H / ,300 5,7 H / ,00 7,66 Design factor 4: Order unit: Drum Welde d C hai n G70 Transport Chain (Half drum) YELLOW ZINC H Trade size (mm) /4 7.0 Wire dia. Inside link dimension A B Feet per /2 drum 400 Lbs per 0/ft 75 Working load limit (Lbs.) (Kgs.) 3,50,42 H / ,700 2,32 H ,600 2,4 H / ,300 5,7 Design factor 4: Order unit: Half drum G70 Transport Chain (5 Gallon pail) YELLOW ZINC H Trade size (mm) /4 7.0 Wire dia. Inside link dimension A B Feet per pail 50 Lbs per pail 5 Working load limit (Lbs.) (Kgs.) 3,50,42 H / ,700 2,32 H Design factor 4: Minimum order quantity: package Catalog weights are approximate 75 6,600 2,4 Order unit: Pail WARNING: Do not exceed the Working Load Limit. Do not use if chain links or component parts are visibly worn, damaged or distorted. Observe the working load limit, as stated in catalog to determine the number of tiedown assemblies and/or hardware required for safe operation per Federal D.O.T. Regulations FMCSA 4CFR Parts 3233, CCMTA and the C.V.S.A. vehicle inspection criteria. Remember, all assemblies are only as strong as their weakest point, including the point of attachment. This chain is NOT designed or approved for overhead lifting. Only G0 Alloy (S) chain is approved for overhead lifting. WARNING: Never exceed Working Load Limit. Load binding systems store energy which can release suddenly, causing serious injury. Stay clear of handle, bars and other binding equipment as it could release without warning and with extreme force. 0

65 HARDWARE Grade 43 High Test Chain Grade 43 is a medium carbon steel that has been formed into links and electronically welded. Designed for applications such as wrecking chain, boomer chain and other areas requiring higher strengthtoweight ratios than Proof Coil (Grade 30). Manufactured to ASTM 0 short link specs. NOT Approved For Overhead Lifting Hallmarked: SCC4, SX4 or S4 every inches G43 High Test Chain (Full drum) SELF COLORED HOT GALVANIZED Trade size (mm) Wire dia. Inside link dimension A B Feet per drum Lbs per 0/ft Working load limit (Lbs.) (Kgs.) H H / ,600,0 H H / ,00,770 H H ,400 2,450 H H02605 / ,200 4,74 Design factor 3: Order unit: Full drum G43 High Test Chain (Half drum) SELF COLORED H Trade size (mm) /4 7.0 Wire dia. Inside link dimension A B Feet per /2 drum 400 Lbs per 0/ft 75 Working load limit (Lbs.) (Kgs.) 2,600,0 Welde d C hai n H / ,00,770 H ,400 2,450 H / ,200 4,74 Design factor 3: Order unit: Half drum G43 High Test Chain (5 Gallon pail) SELF COLORED BRIGHT ZINC Trade size (mm) Wire dia. Inside link dimension A B Feet per pail Lbs per pail Working load limit (Lbs.) (Kgs.) H H0204 / ,600,0 H H0205 5/ ,00,770 H H ,400 2,450 H02005 / ,200 4,74 Design factor 3: Order unit: Pail WARNING: Do not exceed the Working Load Limit. Do not use if chain links or component parts are visibly worn, damaged or distorted. This chain is NOT designed or approved for overhead lifting. Only G0 Alloy (S) chain is approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 65

66 HARDWARE Grade 30 Proof Coil Chain Grade 30 Proof Coil is made from low carbon steel and is a general utility chain for such uses as farm, log chain and tow and switch chain. SCC offers G30 chain in both long link (made to NACM specʼs) and short link (made to ASTM 0 specʼs). Long Link chain has a longer inside length to save weight and reduce cost. Both long and short link chain have the same strength ratings. NOT Approved For Overhead Lifting Hallmarked: SCC3, SX3 or S3 every inches G30 Proof Coil Chain Short Link (Full drum) SELF COLORED BRIGHT ZINC HOT GALVANIZED H H0603 H06035 Trade size (mm) 3/6 5.5 Wire dia. 0.2 Inside link dimension A B Feet per drum 500 Lbs per 0/ft 4 Working load limit (Lbs.) (Kgs.) H H0604 H06045 / , H H0605 H / ,00 62 H H0606 H ,650,202 H06000 H060 H0605 / ,500 2,042 H06000 H0605 5/ ,00 3,3 H0600 H065 3/ ,750 4,424 Welde d C hai n Design factor 4: G30 Proof Coil Chain Short Link (Half drum) SELF COLORED BRIGHT ZINC HOT GALVANIZED H04025 Trade size (mm) / 4.0 Wire dia Inside link dimension A B Feet per /2 drum,000 Lbs per 0/ft 23 Order unit: Full drum Working load limit (Lbs.) (Kgs.) 400 H H0403 H / H H0404 H04045 / , H H0405 H / ,00 62 H H0406 H ,650,202 H04000 H040 H0405 / ,500 2,042 Design factor 4: Order unit: Half drum G30 Proof Coil Chain Long Link (Full drum) BRIGHT ZINC HOT GALVANIZED H0704 H07045 Trade size (mm) /4 7.0 Wire dia Inside link dimension A B Feet per drum 00 Lbs per 0/ft 63 Working load limit (Lbs.) (Kgs.), H0705 H / ,00 62 H0706 Design factor 4: H Order unit: Full drum 66 Minimum order quantity: package Catalog weights are approximate 0.55 WARNING: Do not exceed the Working Load Limit. Do not use if chain links or component parts are visibly worn, damaged or distorted. This chain is NOT designed or approved for overhead lifting. Only G0 Alloy (S) chain is approved for overhead lifting ,650,202

67 HARDWARE Grade 30 Proof Coil Chain Grade 30 Proof Coil is made from low carbon steel and is a general utility chain for such uses as farm, log chain and tow and switch chain. SCC offers G30 chain in both long link (made to NACM specʼs) and short link (made to ASTM 0 specʼs). Long Link chain has a longer inside length to save weight and reduce cost. Both long and short link chain have the same strength ratings. G30 Proof Coil Chain Long Link (Half drum) NOT Approved For Overhead Lifting BRIGHT ZINC HOT GALVANIZED Trade size (mm) Wire dia. Inside link dimension A B Feet per /2 drum Lbs per 0/ft Working load limit (Lbs.) (Kgs.) H0504 H05045 / , H0505 H / ,00 62 H0506 H ,650,202 Design factor 4: Order unit: Half drum G30 Proof Coil Chain Long Link (5 Gallon round pail) SELF COLORED BRIGHT ZINC HOT GALVANIZED Trade size (mm) Wire dia. Inside link dimension A B Feet per pail Lbs per pail Working load limit (Lbs.) (Kgs.) H0025 / H00300 H003 H0035 3/ H00400 H004 H0045 / , H00500 H005 H0055 5/ ,00 62 H00600 H006 H ,650,202 H0000 H00 H005 / Design factor 4: G30 Proof Coil Chain Long Link (4.25 Gallon square pail) ,500 2,042 Order unit: Pail Welde d C hai n BRIGHT ZINC Trade size (mm) Wire dia. Inside link dimension A B Feet per pail Lbs per pail Working load limit (Lbs.) (Kgs.) H003 3/ H004 / , H005 5/ ,00 62 H ,650,202 Design factor 4: Order unit: Pail G30 Proof Coil Chain Long Link ( Reel) BRIGHT ZINC HOT GALVAZINED Trade size (mm) Wire dia. Inside link dimension A B Feet per reel Lbs per reel Working load limit (Lbs.) (Kgs.) H0703 H / H0704 H07045 / , H0705 H / ,00 62 H0706 Design factor 4: H Order unit: Reel Catalog weights are approximate Minimum order quantity: package WARNING: Do not exceed the Working Load Limit. Do not use if chain links or component parts are visibly worn, damaged or distorted. This chain is NOT designed or approved for overhead lifting. Only G0 Alloy (S) chain is approved for overhead lifting ,650,202

68 HARDWARE Stainless Steel Chain & Accessories Stainless steel chain A36 is a nonmagnetic alloy chain, composed of Manganese, Chromium, Nickel & Molybdenum, made to ASTM 0 specifications. It is highly resistant to salt water and chemicals and will not spark. Its uses include food processing, marine, fishing and industrial applications when high corrosion resistance is required. Stainless steel chain A304 is a longer pitch link made to NACM specifications and the alloying components exclude the use of Molybdenum. It has lower Working Load Limits than A36 and is used mainly for decorative and low load applications. NOT Approved For Overhead Lifting A36 Stainless Steel Chain (Half drum) A36 Hallmarked: SCC36 every inches / A304 Hallmarked: SCC304 every inches STAINLESS Trade size (mm) Wire dia. Inside link dimension A B Feet per /2 drum Lbs per 0/ft Working load limit (Lbs.) (Kgs.) H / , H40440 / , H / ,50,23 Stainless Steel Chain & Accessories H40640 H4040 Design factor 4: / A304 Stainless Steel Chain (Half drum) STAINLESS H40340 H40440 H40540 H40640 Trade size (mm) 3/6 5.5 /4 5/ Wire dia Inside link dimension A B Feet per /2 drum Lbs per 0/ft ,00 6,500,724 2,4 Order unit: Half drum Working load limit (Lbs.) (Kgs.) ,300,00 2, ,202 H4040 / ,500 2,042 Design factor 4: Order unit: Half drum Stainless Quick Link (A36) STAINLESS H H H H H H Design factor 4: Trade size (mm) / 4 3/6 /4 5/6 /2 5 6 Dimensions L D W P Working load limit (Lbs.) (Kgs.) package 5 / ctn,270 5 / ctn 6 Minimum order quantity: package Catalog weights are approximate 00,250,00 2,400 2,00 WARNING: Do not exceed the Working Load Limit. Do not use if chain links or component parts are visibly worn, damaged or distorted. This chain is NOT designed or approved for overhead lifting. Only G0 Alloy (S) chain is approved for overhead lifting ,0 5 / ctn 5 / ctn 5 / ctn 5 / ctn

69 HARDWARE Stainless C Chain Link (A36) Stainless Steel Chain Accessories STAINLESS Trade size (mm) Dimensions L d D T Working load limit (Lbs.) (Kgs.) package H / / ctn H / / ctn H / / ctn H / ctn H / ,0 4 5 / ctn Design factor 4: Stainless Snap Pear Hook (A36) STAINLESS H H H H H Design factor 4: Trade size (mm) 3/6 /4 5/6 / Dimensions OL L W D d P Stainless Screw Pin Bow Shackle (A36) STAINLESS H H H H H Design factor 4: Trade size (mm) 3/6 5.5 /4 5/6 / Dimensions W D E d L OL T Working load limit (Lbs.) (Kgs.) ,060,600 2,200 5 / ctn package 5 / ctn Working load limit (Lbs.) (Kgs.) ,060,600 2,00 5 / ctn 5 / ctn 5 / ctn package 5 / ctn 5 / ctn 5 / ctn 5 / ctn,270 5 / ctn Stainless Steel Accessories Stainless Screw Pin D Shackle (A36) STAINLESS Trade size (mm) Dimensions W D T d L OL Working load limit (Lbs.) (Kgs.) package H / / ctn H / / ctn H / , / ctn H , / ctn H24040 / ,00,270 5 / ctn Design factor 4: WARNING: Do not exceed the Working Load Limit. Do not use if chain links or component parts are visibly worn, damaged or distorted. This chain is NOT designed or approved for overhead lifting. Only G0 Alloy (S) chain is approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 6

70 HARDWARE Machine & Passing Link Chain Not Approved For Overhead Lifting Machine chain is a short link welded chain, designed for applications where compactness and flexibility are required. It is generally used on tailgates, farm and industrial equipment. Twist Link Machine Chain (Reel & pail) BRITE ZINC Trade size Wire dia. Inside link dimension A B Feet per package Lbs per Working load limit (Lbs.) (Kgs.) H0602 2/ /2 reel H06024 # /2 reel H062 2/ gal. pail Design factor 4: Order unit: Reel or pail Straight Link Machine Chain (Reel & pail) BRITE ZINC Trade size Wire dia. Inside link dimension A B Feet per package Lbs per Working load limit (Lbs.) (Kgs.) Welde d C hai n H07072 H07024 H072 H0724 Design factor 4: 2/0 #4 2/0 # /2 reel 6 /2 reel 5 gal. pail 5 gal. pail Order unit: Reel or pail Passing Link Chain (Reel, pail & carton) Passing link chain has a wide link design that allows links to pass one another freely, minimizing kinking and tangling. It is used for farm machinery, animal ties and as a general utility chain. BRITE ZINC Trade size Wire dia. Inside link dimension A B Feet per package Lbs per Working load limit (Lbs.) (Kgs.) H0072 2/ /2 reel H02 2/ gal. pail H0202 2/ Carton H0202 4/ Carton Design factor 4: Order unit: Reel, pail or carton WARNING: Do not exceed the Working Load Limit. Do not use if chain links or component parts are visibly worn, damaged or distorted. This chain is NOT designed or approved for overhead lifting. Only G0 Alloy (S) chain is approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

71 HARDWARE Coil Chain Not Approved For Overhead Lifting Coil chain has a longer link than Proof Coil or Machine Chain and therefore is less flexible. Uses include animal tie chain, agricultural implement chain and platform guard rail chain. Twist Link Coil Chain (Reel & carton) BRITE ZINC Trade size Wire dia. Inside link dimension A B Feet per package Lbs per package Working load limit (Lbs.) (Kgs.) H0502 2/ /2 reel H / Carton Design factor 4: Order unit: Reel or carton Straight Link Coil Chain (Reel & pail) BRITE ZINC H0072 H0072 H0022 H02 Trade size 2/0 4/0 #2 2/0 Wire dia Inside link dimension A B Feet per package /2 reel /2 reel 6 /2 reel 5 gal. pail Lbs per package Working load limit (Lbs.) (Kgs.) Welde d C hai n Design factor 4: Order unit: Reel or pail Straight Link Coil Chain (Carton) BRITE ZINC Trade size Wire dia. Inside link dimension A B Feet per carton Lbs per carton Working load limit (Lbs.) (Kgs.) H02020 / H0202 2/ H02022 # H02024 # H0202 4/ H0203 5/ H0203 6/ , Design factor 4: Order unit: Carton WARNING: Do not exceed the Working Load Limit. Do not use if chain links or component parts are visibly worn, damaged or distorted. This chain is NOT designed or approved for overhead lifting. Only G0 Alloy (S) chain is approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 7

72 HARDWARE Double Loop & Lock Link Chain Not Approved For Overhead Lifting Double Loop chain is a machine woven weldless chain with two identical size loops, securely knotted in the center. General utility chain for hardware/manufacturing applications such as playground and gym equipment, fluorescent lights, boats, gates, porch swings, halters, cow ties and tieout chains. Double Loop Chain (Reel & pail) YELLOW WHITE BRITE ZINC Trade size Wire dia. Inside length A B Feet per package Lbs. per package Working load limit (Lbs.) (Kgs.) H / /2 reel H H H / /2 reel H H / /2 reel H20020 / /2 reel H H20025 # /2 reel H # /2 reel H202 2/ gal. pail H2025 # gal. pail H2026 # gal. pail Weldless Chain Design factor 4: Special Well Chain (Carton) Well chain has a longer pitch (inside length) than Double Loop Chain. Used for general utility, farm and animal tieout. Order unit:reel or pail Wire dia. Inside length Feet per Lbs per Working load limit BRITE ZINC Trade size A B carton carton (Lbs.) (Kgs.) H203 2/ Carton Design factor 4: Order unit: Carton Lock Link Single Loop Chain (Reel) Lock Link Chain is a weldless flexible chain used for operating overhead doors, skylights or other sprocket wheel or valve wheel activated mechanisms. It is the strongest weldless chain. Wire dia. Inside length Feet per Lbs per Working load limit BRITE ZINC Trade size A B reel reel (Lbs.) (Kgs.) H2722 3/ /2 reel Design factor 4: Order unit: Reel WARNING: Do not exceed the Working Load Limit. Do not use if chain links or component parts are visibly worn, damaged or distorted. This chain is NOT designed or approved for overhead lifting. Only G0 Alloy (S) chain is approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

73 HARDWARE Single Jack & Brass Safety Chain Not Approved For Overhead Lifting Single Jack Chain is a weldless chain shaped in a figure pattern. Single Jack Chain is used in areas that do not require high strength, such as hanging signs, light fixtures and scales. Single Jack Chain (Reel & carton) Trade size Wire diameter Inside length Feet per BRASS PLATED BRITE ZINC (Gauge) (mm) A package H /2 reel Lbs. per package 37 Working load limit (Lbs.) (Kgs.) H H /2 reel H H /2 reel 2 3 H /2 reel H /2 reel H H /2 reel 6 7 H H /2 reel 5 H ,000 6 /2 reel 5 2 H Carton Design factor 4: H2233 H22332 H Carton Carton Carton Order unit: Reel or carton Weldless Chain Brass Safety / Plumber s Chain (Reel) This weldless flexible chain is widely used for attaching plumbing fixtures, for pulley service and general utility chain. BRASS Trade size Material thickness Inside length Feet per (mm) A reel Lbs per reel Working load limit (Lbs.) (Kgs.) H / /2 reel 6 40 H Design factor 4: / /2 reel Order unit: Reel WARNING: Do not exceed the Working Load Limit. Do not use if chain links or component parts are visibly worn, damaged or distorted. This chain is NOT designed or approved for overhead lifting. Only G0 Alloy (S) chain is approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package

74 HARDWARE Sash Chain / Plastic Chain & Accessories NOT Approved For Overhead Lifting A stamped, flat link chain that is widely used when a flat metal chain is required. Sash Chain operates smoothly over pulleys. Also suitable for lamp chain, tool boxes and many other applications. Sash Chain (Reel) BRITE ZINC Trade size Material thickness Inside length Feet per (mm) A reel Working load limit (Lbs.) (Kgs.) H24034 # /2 reel Lbs per reel Design factor 4: Order unit: Reel Plastic Chain (4.25 Gallon Square Pail) A light duty plastic chain made of Polypropylene used mainly for decorative purposes, as a barrier or to guide traffic. Plastic chain is durable, light weight and weather resistant. Available in 4 colors and 2 sizes. Weldless Chain WHITE YELLOW RED HOT ORANGE Trade size (mm) Diameter Inside Dim. A B Feet per pail Lbs per pail Working load limit (Lbs.) (Kgs.) H H H H / gal H H H H / gal Design factor 3: Order unit: Pail Plastic Chain Connecting Link Split links of plastic chain used to connect two pieces of plastic chain together. Available in all the same colors as the plastic chain. WHITE YELLOW RED HOT ORANGE Trade size (mm) Diameter Inside Dim. A B (Lbs/pkg) package Working load limit (Lbs.) (Kgs.) H H H H / / ctn 25 H H H H / / ctn 40 Design factor 3: WARNING: Do not exceed the Working Load Limit. Do not use if chain links or component parts are visibly worn, damaged or distorted. This chain is NOT designed or approved for overhead lifting. Only G0 Alloy (S) chain is approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

75 HARDWARE T0 & G70 Hooks & Coupling Links NOT Approved For Overhead Lifting Transport (T0) Clevis Grab Hook Drop forged, alloy steel hook, quenched and tempered. Use with Grade 0 Tiedown chain only. BLACK Chain Size A Dimensions B C D Working Load Limit (Lbs) H ,0 / ctn H / ,000 / ctn Design factor 4: G70 Clevis Grab Hook Drop forged, medium alloy steel hook, quenched and tempered. Use with G70 Transport Chain. SELF COLOR YELLOW ZINC Chain Size A Dimensions B C D Working Load Limit (Lbs) H H / ,600 / ctn H H / ,400 / ctn H H ,500 / ctn H H / ,500 / ctn H / ,200 5 / ctn Design factor 4: G70 Clevis Slip Hook with Latch Drop forged, medium alloy steel hook, quenched and tempered. Use with G70 Transport Chain. Slip hooks have a lower Working Load Limit than the same type/size chain or grab hook. SELF COLOR YELLOW ZINC H H Chain Size /4 5/6 Dimensions A B C D E Working Load Limit (Lbs) 2,750 4,300 / ctn / ctn Chain Accessories H ,250 / ctn H / ,000 / ctn H / ,00 5 / ctn Design factor 4: G70 Coupling Link Drop forged, medium alloy steel, quenched and tempered. Use with G70 Transport Chain. YELLOW ZINC Chain Size A Dimensions B C D Working Load Limit (Lbs) H / ,250 5 / ctn H / ,700 5 / ctn H ,600 5 / ctn H / ,500 5 / ctn H / ,200 5 / ctn Design factor 4: WARNING: Do not exceed the Working Load Limit. Inspect all parts for distortion, cracks or damage prior to use. If the pin or eye is worn or distorted remove the part from service immediately and replace. Never point or tip load a hook. Never subject a hook to shock loading or jerking. These parts are NOT designed or approved for overhead lifting. Only G0 Alloy (S) hooks and fittings are approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 75

76 HARDWARE Hooks for G30 & G43 Chain G43 Clevis Grab Hook Drop forged, carbon steel hook, heat treated. Use with G30 Proof Coil or G43 High Test. SELF COLOR BRIGHT ZINC Chain Size A Dimensions B C D Working Load Limit (Lbs) H H / ,600 / ctn H H / ,00 / ctn H H ,400 / ctn H H76260 / ,200 / ctn Design factor 4: G43 Clevis Slip Hook with Latch Drop forged, carbon steel hook, heat treated. Use with G30 Proof Coil or G43 High Test. Slip hooks have a lower Working Load Limit than the same type/size chain or grab hook. SELF COLOR BRIGHT ZINC Chain Size A Dimensions B C D E Working Load Limit (Lbs) H / ,50 / ctn H / ,75 / ctn H ,000 / ctn H75260 / ,500 / ctn Design factor 4: Chain Accessories G43 Clevis Slip Hook Drop forged, carbon steel hook, heat treated. Use with G30 Proof Coil or G43 High Test. Slip hooks have a lower Working Load Limit than the same type/size chain or grab hook. SELF COLOR BRIGHT ZINC H Chain Size /4 Dimensions A B C D Working Load Limit (Lbs),50 / ctn H / ,75 / ctn H ,000 / ctn H74260 / ,500 / ctn Design factor 4: G43 Eye Grab Hook Drop forged, carbon steel hook, heat treated. Use with G30 Proof Coil or G43 High Test. SELF COLOR BRIGHT ZINC Chain Size Dimensions A B C Working Load Limit (Lbs) H H / ,600 / ctn H H / ,00 / ctn H H ,400 / ctn H H72260 / ,200 / ctn Design factor 4: WARNING: Do not exceed the Working Load Limit. Inspect all parts for distortion, cracks or damage prior to use. If the pin or eye is worn or distorted remove the hook from service immediately and replace. Never point or tip load a hook. Never subject a hook to shock loading or jerking. These hooks are NOT designed or approved for overhead lifting. Only G0 Alloy (S) hooks and fittings are approved for overhead lifting Minimum order quantity: package Catalog weights are approximate

77 HARDWARE G43 Eye Slip Hook with Latch Hooks for G30 & G43 Chain & Latch Kits Drop forged, carbon steel hook, heat treated. Use with G30 Proof Coil or G43 High Test. Slip hooks have a lower Working Load Limit than the same type/size chain or grab hook. SELF COLOR BRIGHT ZINC Chain Size A Dimensions B C D Working Load Limit (Lbs) H7604 / ,50 / ctn H7605 5/ ,75 / ctn H ,000 / ctn H760 / ,500 / ctn Design factor 4: G43 Eye Slip Hook Drop forged, carbon steel hook, heat treated. Use with G30 Proof Coil or G43 High Test. Slip hooks have a lower Working Load Limit than the same type/size chain or grab hook. SELF COLOR BRIGHT ZINC Chain Size Dimensions A B C Working Load Limit (Lbs) H / ,50 / ctn H / H H70260 / Design factor 4: Replacement Latch Kits (For SCC G70 & G43 slip hooks) 2,75 / ctn 4,000 / ctn 6,500 / ctn Chain Accessories BRIGHT ZINC For Hook Size Description Working Load Limit (Lbs) H77504 /4 For SCC slip hooks 0.25 N/A / ctn H /6 For SCC slip hooks 0.30 N/A / ctn H77506 For SCC slip hooks 0.50 N/A / ctn H7750 /2 For SCC slip hooks 0.70 N/A / ctn WARNING: Do not exceed the Working Load Limit. Inspect all parts for distortion, cracks or damage prior to use. If the pin or eye is worn or distorted remove the hook from service immediately and replace. Never point or tip load a hook. Never subject a hook to shock loading or jerking. These hooks are NOT designed or approved for overhead lifting. Only G0 Alloy (S) hooks and fittings are approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 77

78 HARDWARE Chain Accessories G70 Double Clevis Drop forged, medium alloy steel, quenched and tempered. Use with G70 Transport chain. YELLOW ZINC Chain Size A Dimensions R D G Working Load Limit (Lbs) H /4 ~ 5/ ,700 / ctn H ,600 / ctn H /6 ~ / ,300 / ctn Design factor 4: G43 Double Clevis Drop forged, medium carbon steel, quenched and tempered. Use with G30 and G43 chain. BRIGHT ZINC Chain Size A Dimensions R D G Working Load Limit (Lbs) H52640 /4 ~ 5/ ,00 / ctn H ,400 / ctn H /6 ~ / ,200 / ctn Design factor 4: Chain Accessories Replacement Clevis Pins (For SCC G43, G70 & T0 Hooks & Double Clevis) Drop forged alloy pins and cotter key for use with SCC accessories. BRIGHT ZINC YELLOW ZINC Trade size Works with these SCC items: GRAB HK SLIP HK DBL. CLVS Dia. D Inside Length B Overall Shaft Length A Working Load Limit (Lbs) H42604 H /4 Yes ,600 / ctn H42605 H /6 Yes ,400 / ctn H42606 H Yes ,500 / ctn H4260 H /2 Yes Yes ,750 / ctn H / Yes Yes ,200 / ctn H /4 5/6 Yes ,400 / ctn H Yes ,500 / ctn H /6 /2 Yes ,750 / ctn H /4 Yes ,600 / ctn H /6 Yes ,400 / ctn H Yes ,500 / ctn Design factor 4: WARNING: Do not exceed the Working Load Limit. Inspect all parts for distortion, cracks or damage prior to use. If the pin or eye is worn or distorted remove the part from service immediately and replace. Never point or tip load a hook. Never subject a hook to shock loading or jerking. These parts are NOT designed or approved for overhead lifting. Only G0 Alloy (S) hooks and fittings are approved for overhead lifting. 7 Minimum order quantity: package Catalog weights are approximate

79 HARDWARE Chain Accessories Repair Lap Link Low carbon steel. For temporary chain repair and coupling of attachments. When using lap links with chain, use one size larger than chain size. Use with low carbon chain only. Lap links shall not be reused after closure has been made BRIGHT ZINC Trade Size Inside Link Dimensions A B Working Load Limit (Lbs) H020 / / ctn H02 3/ / ctn H022 / / ctn H025 5/ / ctn H , / ctn H , / ctn H024 / ,5 25 / ctn Design factor 3: Cold Shuts Low carbon steel. For temporary chain repair and coupling of attachments. When using cold shuts with chain, use one size larger than chain size. Use with low carbon chain only. Cold shuts shall not be reused after closure has been made BRIGHT ZINC H603 H604 H605 H606 Trade Size 3/6 /4 5/6 Inside Link Dimensions A B Working Load Limit (Lbs) ,250,00 / ctn / ctn / ctn / ctn Chain Accessories H60 / ,500 / ctn Design factor 3: Quick Links Low carbon steel. Fast, easy connection for permanent or temporary connection. Use with low carbon chain only BRITE ZINC Trade Size Diameter (mm) Link Dimensions A B C D E Working Load Limit (Lbs) H22602 / / ctn H / / ctn H22604 / / ctn H / ,760 / ctn H ,200 / ctn H / ,600 / ctn H2260 / ,300 / ctn Design factor 4: WARNING: Do not exceed the Working Load Limit. Inspect all parts for distortion, cracks or damage prior to use. These items are NOT designed or approved for overhead lifting. Only G0 Alloy (S) hooks and fittings are approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 7

80 HARDWARE Chain Accessories Connecting Link Drop forged medium carbon steel, heat treated. For temporary chain repair and coupling of attachments. For proper closure, peen pins to completely fill eye of mated half. Use with low carbon chain only BRIGHT ZINC HOT GALVANIZED Chain Size Dimensions A B Working Load Limit (Lbs) H32603 H / / ctn H32604 H / ,400 / ctn H32605 H / ,000 / ctn H32606 H ,00 / ctn H3260 H32605 / ,750 / ctn Design factor 4: Snap Pear Hook Low carbon steel. Fast, easy attachment for permanent or temporary connection. Use with low carbon chain only BRITE ZINC Trade Size Diameter (mm) A Dimensions B C X Working Load Limit (Lbs) H72602 / / ctn H / / ctn H72604 / / ctn Chain Accessories H /6 H72606 H /6 H7260 /2 Design factor 4: / ctn 550 / ctn 770 / ctn,200 / ctn S Hook Made from low carbon steel (preplated) wire. See sizing chart on page. Use with low carbon chain only BRIGHT ZINC Trade Size (Number) Wire Dia. Dimensions A B Working Load Limit (Lbs) H / ctn H / ctn H / ctn H / ctn H / ctn H / ctn H / ctn H / ctn Design factor 3: WARNING: Do not exceed the Working Load Limit. Inspect all parts for distortion, cracks or damage prior to use. These items are NOT designed or approved for overhead lifting. Only G0 Alloy (S) hooks and fittings are approved for overhead lifting. 0 Minimum order quantity: package Catalog weights are approximate

81 HARDWARE Chain Accessories SHOOK IDENTIFICATION CHART: #20 H4227 #30 H4234 #40 H4235 #5 H42360 #60 H4236 #0 H4237 Chain Accessories #0 H423 #0 H423 WARNING: Do not exceed the Working Load Limit. Inspect all parts for distortion, cracks or damage prior to use. These items are NOT designed or approved for overhead lifting. Only G0 Alloy (S) hooks and fittings are approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package

82 HARDWARE Chain Accessories Screw Pin Anchor Shackle Commercial grade shackles ARE NOT approved for overhead lifting Commercial grade, upset forged 5 steel. For joining welded chain to attachments. Chain Accessories HOT GALVANIZED BRIGHT ZINC H H62603 H H62604 H H62605 H H62606 H H62605 H62605 H6265 Design factor 4: HOT GALVANIZED H H H H H H64505 H64505 H6455 H6455 H6455 H64535 H64545 H64565 H64575 Design factor 4: Size 3/6 /4 5/6 7/6 /2 5/ 3/4 Pin dia. Forged Trawling Shackle Pin dia. /4 5/6 7/6 /2 5/ 3/4 7/ Dimensions W D A E G H B Forged Screw Pin Anchor Shackle Drop forged 45 steel. Hot galvanized and load rated. For joining welded chain attachments. Meets Federal Specs. #RRC27D, Type IV A, Grade A, Class 2. Pin = 430 Alloy. Size 3/6 /4 5/6 7/6 /2 5/ 3/4 7/ / /4 /2 /4 5/6 7/6 /2 5/ 3/4 7/ / /4 /2 5/ Dimensions W D A E G H B Working load limit (Lbs) package 500 / ctn 667 / ctn,000 / ctn,500 / ctn 2,000 / ctn 3,000 / ctn 4,500 5 / ctn 6,500 4 / ctn Working load limit (Lbs) package / ctn, / ctn, / ctn 2, / ctn 3, / ctn 4, / ctn 6, / ctn, / ctn 3,000 / ctn 7,000 / ctn,000 / ctn 24,000 5 / ctn 27,000 Each 34,000 Each Commercial grade shackles ARE NOT approved for overhead lifting Commercial grade, upset forged 5 steel. For joining welded chain to attachments. SELF COLOR LAQUER H H H62624 H6264 H62624 Design factor 4: Size /2 5/ 3/4 7/ Pin dia. 5/ 3/4 7/ / Dimensions W D A B G H Working load limit (Lbs) package 2 Minimum order quantity: package Catalog weights are approximate ,250 / ctn 2,000 / ctn 2,750 / ctn 3,750 5 / ctn 5,000 5 / ctn WARNING: Do not exceed the Working Load Limit. Inspect all shackles for distortion or damage prior to use. If the pin or eye is worn or distorted, remove the shackle from service immediately and replace. Do not use screw pin anchor shackles in applications where the thumb grip could be hit and cause pin movement. Use safety shackles in these applications. All working load limits stated are for a straight pull perpendicular against the pin. If the pull is angular, the load must be on the bow and the stated working load is reduced by 30% at 45 and 50% at 0. Commercial grade shackles are not designed/approved for overhead lifting.

83 HARDWARE Chain Accessories Forged Safety Shackle Drop forged 45 steel. Load rated. For joining welded chain attachments. Meets Federal Specs. #RRC27D, Type IV A, Grade A, Class 3. Pin = 430 Alloy. HOT GALVANIZED H4505 H4505 H455 H455 H455 H4535 H4545 H4565 H4575 Design factor 4: Size /2 5/ 3/4 7/ / /4 /2 Pin dia. 5/ 3/4 7/ / /4 /2 5/ Dimensions W D A E G B H Working load limit (Lbs) 4,000 6,500,500 3,000 7,000,000 24,000 27,000 34,000 package 25 / ctn 25 / ctn 25 / ctn / ctn 5 / ctn 5 / ctn 5 / ctn Each Each D Chain Shackle Commercial grade shackles ARE NOT approved for overhead lifting Commercial grade, upset forged 5 steel. For joining welded chain to attachments. Size Pin dia. Dimensions BRIGHT ZINC C D B G A H H2603 3/6 / H2604 /4 5/ H2605 5/ H2606 7/ Design factor 4: Forged D Chain Shackle Drop forged 45 steel. Hot galvanized and load rated. For joining welded chain attachments. Meets Federal Specs. #RRC27D, Type IV B, Grade A, Class 2. Pin = 430 Alloy. HOT GALVANIZED H45035 H45045 H45055 H45065 H4505 H4505 H455 H455 H455 H4535 H4545 H4565 H4575 Design factor 4: Size 3/6 /4 5/6 /2 5/ 3/4 7/ / /4 /2 Pin dia. /4 5/6 7/6 5/ 3/4 7/ / /4 /2 5/ Dimensions C D B G A H Working load limit (Lbs) ,000,500 Working load limit (Lbs) 667,000,500 2,000 4,000 6,500,500 3,000 7,000,000 24,000 27,000 package / ctn / ctn / ctn / ctn package 25 / ctn 25 / ctn 25 / ctn 25 / ctn / ctn / ctn / ctn 5 / ctn 5 / ctn 5 / ctn 5 / ctn Each 34,000 Each WARNING: Do not exceed the Working Load Limit. Inspect all shackles for distortion or damage prior to use. If the pin or eye is worn or distorted, remove the shackle from service immediately and replace. Do not use screw pin anchor shackles in applications where the thumb grip could be hit and cause pin movement. Use safety shackles in these applications. All working load limits stated are for a straight pull perpendicular against the pin. If the pull is angular, the load must be on the bow and the stated working load is reduced by 30% at 45 and 50% at 0. Commercial grade shackles are not designed/approved for overhead lifting. Chain Accessories Catalog weights are approximate Minimum order quantity: package 3

84 HARDWARE Malleable Steel Snaps & Swivels H & H H H60260 H60265 H60266 ~ H6026 H6026 H H ~ H H H H & H H & H H & H H60265 H & H60262 Chain Accessories H H H H60260 H60265 H60266 H60267 H6026 H6026 H6026 H H H H H H H H H H H H H H60265 H H60262 Description Spring snap Jiffy link Spring snap Jiffy link Spring snap Jiffy link Open eye bolt Round eye swivel spring snap Round eye swivel bolt snap Round eye swivel bolt snap Round eye swivel bolt snap Round eye swivel bolt snap Round eye swivel animal snap Round eye swivel spring snap Round eye swivel trigger snap Round eye swivel trigger snap Round eye swivel trigger snap Round eye swivel trigger snap Strap eye swivel trigger snap Round eye swivel trigger snap Strap eye swivel rein snap Strap eye swivel rein snap Round eye swivel rein snap Round eye swivel rein snap Double swivel closed Double swivel closed Round eye swivel quick snap Double end bolt snap Double end bolt snap Finish Yellow Zinc Yellow Zinc Bright Zinc Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Nickel Dimensions A B C Open /2 5/ 3/4 7/ 3/4 /2 5/ 3/4 3/4 3/4 3/4 3/4 /2 3/4 3/4 5/ 3/ package / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn WARNING: These snaps and snap hooks are not designed for load support, human support or cargo tie down. Never use these items for support of a person or other application where strength or personal safety is a factor. Serious personal injury or loss of life may result. These items are NOT designed for overhead lifting. Only G0 Alloy (S) hooks and fittings are approved for overhead lifting. 4 Minimum order quantity: package Catalog weights are approximate

85 HARDWARE Drop Forged Latch Snaps H H60260 H6026 Description Finish Dimensions A B C Working load limit (Lbs.) package H Forged fixed eye safety snap Bright Zinc 5/ , / ctn H60260 Forged fixed eye safety snap Bright Zinc 5/ , / ctn H6026 Forged fixed eye safety snap Bright Zinc 5/ / ctn Design factor 4: Wire Formed Snaps & Swivels H6026 H60266 H60267 H & H H6026 H60266 H60267 H H Description Round eye swivel spring snap Open eye swivel spring snap Open eye swivel spring snap Double swivel open Double swivel open Finish Bright Zinc Bright Zinc Bright Zinc Bright Zinc Bright Zinc Dimensions A B C 3/ Open Open 3.3 Open #3 #4 Open /0 2/ package / ctn / ctn / ctn / ctn / ctn Chain Accessories Bronze Die Cast Snaps H663 H66263 H6653 H66237 H663 H66263 H6653 H66237 Description Round eye swivel trigger snap Open eye swivel trigger snap Open eye swivel quick snap Double end bolt snap Finish Bronze Bronze Bronze Bronze Dimensions A B C 3/ package / ctn WARNING: These snaps and snap hooks are not designed for load support, human support or cargo tie down. Never use these items for support of a person or other application where strength or personal safety is a factor. Serious personal injury or loss of may result. These items are NOT designed for overhead lifting. Only G0 Alloy (S) hooks and fittings are approved for overhead lifting. Catalog weights are approximate Minimum order quantity: package 5 /2 3/4 5/ / ctn / ctn / ctn

86 HARDWARE Galvanized Aircraft Cable (GAC) Cable is highstrength, aircraft quality with an electrogalvanized zinc finish. It is either 7x7 or extra flexible 7x construction as illustrated. Approved For Overhead Lifting Aircraft Cable (Reel putups) 7 x 7 7 x Cable size Type construction Feet per reel Reel width per reel (Lbs) Working load limit LBS KGS H3002 / 7 x H3003 3/6 7 x H3004 /4 7 x , H3005 5/6 7 x , H /6 7 x H4000 3/32 7 x H40002 / 7 x Design factor 5: Order unit: Reel Aircraft Cable (Reels and spools) Aircraft Cable H30702 H30703 H30704 H30705 H30706 H3002 H3003 H3004 H3005 H3006 H H40070 H H40000 H4000 H40002 Design factor 5: Cable size / 3/6 /4 5/6 / 3/6 /4 5/6 /6 3/32 / /6 3/32 / Type construction 7 x 7 x 7 x 7 x 7 x 7 x 7 x 7 x 7 x 7 x 7 x 7 7 x 7 7 x 7 7 x 7 7 x 7 7 x 7 Feet per reel 5,000 5,000 5,000 5,000 5,000,000,000,000,000,000 5,000 5,000 5,000,000,000,000 Reel width Wood Spool Wood Spool Wood Spool Wood Spool Wood Spool 6 Wood Spool Wood Spool Wood Spool Wood Spool Wood Spool Wood Spool Wood Spool per reel (Lbs) , Working load limit LBS KGS , , ,0, , , ,0, Order unit: Reel or spool WARNING: Failure to follow these warnings and instructions can result in property damage, serious personal injury and or loss of life. DO NOT Exceed Working Load Limit (WLL). GAC and wire rope require proper care and maintenance, as such we recommend users follow the recommended practices as published in the "Wire Rope Users Manual" available from The American Iron & Steel Institute. All attachments must have at least the same WLL as the cable used. Clips, Thimbles, Sleeves, Hooks, Links, Shackles etc. must match in size, material and strength to provide for adequate safety. Proper installation is required for personal safety and maximum life of the assembly. Inspect all cable assemblies and attachments prior to each use. If any visible damage is apparent (including any broken wire strands) dispose of the cable assembly and replace. For specific inspection procedures and requirements consult ANSI and OSHA standards. USE OF THESE PRODUCTS DEMONSTRATES AN UNDERSTANDING OF THESE WARNINGS AND THE RISKS INVOLVED. 6 Minimum order quantity: package Catalog weights are approximate

87 HARDWARE Coated Aircraft Cable (GAC) Cable is highstrength, aircraft quality with an electrogalvanized zinc finish. PVC coated cable is more resistant to abrasion and weathering. Cable is either 7x7 or extra flexible 7x construction as illustrated. Approved For Overhead Lifting Vinyl coating must be removed from cable before attaching wire rope clips. PVC Coated Aircraft Cable (Reel putups) 7 x 7 7 x Cable Size Type construction Size w/coating Feet per reel Reel width (Inches.) per reel (Lbs) Working load limit LBS KGS H3003 3/6 7 x / H3004 /4 7 x 5/ , H40 3/32 7 x 7 3/ H402 / 7 x 7 3/ Design factor 5: Order unit: Reel PVC Coated Aircraft Cable (Bulk spools) H30703 H30704 H4700 H470 H4702 Design factor 5: Cable Size 3/6 /4 /6 3/32 / Type construction 7 x 7 x 7 x 7 7 x 7 7 x 7 Forged Hook & Eye Turnbuckle Size w/coating /4 5/6 / 3/6 3/6 Feet per reel 5,000 5,000 5,000 5,000 5,000 Wood spool Wood spool Wood spool Wood spool Wood spool per reel (Lbs) Working load limit LBS KGS 40 3, Order unit: Reel Aircraft Cable & Accessories Drop forged, carbon steel. Commercial grade, hot dip galvanized. Conforms to Federal Specification FFT7B, Type, Form Class 6. End fittings are quenched and tempered. Bodies are normalized. Turnbuckles are NOT Approved For Overhead Lifting HOT GALVANIZED Trade size Take up A B C D Dimensions E F G H K P Working load limit (Lbs.) (Lbs /ea.) H / / ctn H / / ctn H Design factor 4: , / ctn WARNING: Failure to follow these warnings and instructions can result in property damage, serious personal injury and or loss of life. DO NOT Exceed Working Load Limit (WLL). GAC and wire rope require proper care and maintenance, as such we recommend users follow the recommended practices as published in the "Wire Rope Users Manual" available from The American Iron & Steel Institute. All attachments must have at least the same WLL as the cable used. Clips, Thimbles, Sleeves, Hooks, Links, Shackles etc. must match in size, material and strength to provide for adequate safety. Proper installation is required for personal safety and maximum life of the assembly. Inspect all cable assemblies and attachments prior to each use. If any visible damage is apparent (including any broken wire strands) dispose of the cable assembly and replace. For specific inspection procedures and requirements consult ANSI and OSHA standards. USE OF THESE PRODUCTS DEMONSTRATES AN UNDERSTANDING OF THESE WARNINGS AND THE RISKS INVOLVED. Catalog weights are approximate Minimum order quantity: package 7

88 HARDWARE Cable Accessories Malleable Wire Rope Clips Commercial grade, malleable iron casting. H H H H H H H H43265 H43265 H43265 Trade size (Inches.) / 3/6 /4 5/6 /2 5/ 3/4 7/ Forged Wire Rope Clips Tightening torque (Ft / Lbs.) Minimum number clips required Drop forged. Meets Federal Spec. #FFC450D Type, Class Dead end turn back Not Approved For Overhead Lifting (Lbs./ea) package / ctn / ctn 0.30 / ctn 0.50 / ctn / ctn / ctn 0.50 / ctn 0.50 / ctn.20 / ctn.500 / ctn Not Approved For Overhead Lifting Cable Accessories H H H H H H H H H43455 H43455 H43455 H Aluminum Oval Sleeves & Stops When they are properly applied with a cable swagger, sleeves are capable of supporting a greater load than the rated breaking strength of the cable to which they are attached. Stops are capable of holding /3 to /2 of the rated breaking strength of the cable to which they are attached. SLEEVES H H36204 H H H H H Trade size (Inches.) / 3/6 /4 5/6 7/6 /2 5/ 3/4 7/ / STOPS H H37204 H H H H H Tightening torque (Ft / Lbs.) To fit cable size /6 3/32 / 3/6 /4 5/6 Minimum number clips required Dead end turn back (Lbs / package) SLEEVES STOPS (Lbs./ea) package / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn / ctn 2.00 / ctn Not Approved For Overhead Lifting package SLEEVES STOPS 50 / ctn 25 / ctn 50 / ctn 25 / ctn 50 / ctn 25 / ctn 50 / ctn 25 / ctn 25 / ctn 25 / ctn 25 / ctn 25 / ctn 25 / ctn 25 / ctn Oval Sleeves WARNING: DO NOT Exceed Working Load Limit (WLL). Make all wire rope clip terminations/splices as illustrated on page. Do not use on coated cable without stripping away coating in the area to be terminated before installing clips. Tighten nut to recommended torque and recheck frequently. Wire rope clips and thimbles are not designed or intended to support loads, as such they have no working load limits or design factors. Thimbles are designed as a wear reduction pad for cable and wire rope and are not intended to support loads. Thimbles should be used whenever an eye is formed in a cable or wire rope. Always match the correct size thimble to the cable. Never use a smaller thimble, as it will pinch and cut wire strands in the cable, reducing the load capacity of the assembly. Stops Minimum order quantity: package Catalog weights are approximate

89 HARDWARE Cable Accessories Wire Rope ThimblesHeavy Duty Type II Not Approved For Overhead Lifting Hot rolled mild steel. Meets federal Spec. FFT276B Type II HOT GALVANIZED Trade size Dimensions A B C D E F G H package H / / ctn H / / ctn H / / ctn H / / ctn H / ctn Wire Rope ThimblesHeavy Duty Type III Not Approved For Overhead Lifting Hot rolled mild steel. Meets federal Spec. FFT276B Type III HOT GALVANIZED Trade size Dimensions A B C D E F G H package H / / ctn H / / ctn H / ctn H / / ctn H / / ctn H H42305 H42305 H / 3/4 7/ / ctn / ctn.0 25 / ctn 3. / ctn Cable Accessories WIRE ROPE TURNBACK PROCEDURE: 2 3 Double the wire rope around a wire rope thimble of the appropriate size, making sure that the "dead end turn back" is at least as long as shown on page. Place the first clip at least as far from the dead end of the cable as the width of the clip base, with the Ubolt part of the clip securing the dead end of the wire rope. Nuts should be tightened equally to the torque values shown on page. The second clip should be placed as close to the thimble as possible. If additional clips are required (see clips specs on page for recommendations) space them evenly between the first two. 4 Tighten all clips to the recommended torque value, making sure that there is no slack in the wire rope between the clips. & WARNING: When a load is first applied to this assembly the nuts must be retightened to the torque values shown. To maintain the assembly in safe working order nuts should be checked regularly and retightened as needed. WARNING: DO NOT Exceed Working Load Limit (WLL). Make all wire rope clip terminations/splices as illustrated above. Do not use on coated cable without stripping away coating in the area to be terminated before installing clips. Tighten nut to recommended torque and recheck frequently. Wire rope clips and thimbles are not designed or intended to support loads, as such they have no working load limits or design factors. Thimbles are designed as a wear reduction pad for cable and wire rope and are not intended to support loads. Thimbles should be used whenever an eye is formed in a cable or wire rope. Always match the correct size thimble to the cable. Never use a smaller thimble, as it will pinch and cut wire strands in the cable, reducing the load capacity of the assembly. Catalog weights are approximate Minimum order quantity: package

90 HARDWARE AntiTheft Chain & Padlocks Brass Combination Locks These locks feature a brass plated zinc diecast body for resistance to rust. The shackle is tempered alloy steel. They have a resettable combination so each lock can be customized with the users personal key code or all set to the same combination. The long shackle model works very well with SCC's QuikBinder Plus to keep the binder, chain & load locked and secure. H is retail packaged in a tamperproof clamshell. H Trade size: 2 Case (50mm) Shackle length: Finish: Brass : 0.60 Lbs./ea package: / ctn H Trade size: 2 Case (50mm) Shackle length: 2 /4 Finish: Brass : 0.75 Lbs./ea package: / ctn Weatherproof Locks These locks are designed with the elements in mind. This specialty lock is completely sealed from the weather. It is constructed of laminated steel with a double locking device for extra protection. The internal lock cylinder is solid brass, has pin tumblers and stainless steel springs. Two solid brass, nickel plated keys accompany each lock. H4246 Trade size: /2 Case (40mm) Shackle length: /4 : 0.6 Lbs./ea package: / ctn H Trade size: /2 Case (40mm) Shackle length: 2 /2 : 0.6 Lbs./ea package: / ctn AntiTheft Products Hex AntiTheft Chain Not Approved For Overhead Lifting Hex chain is a high alloy chain drawn in a six sided (hexagonal) shape and heat treated to be extremely hard. The hex shape does not allow a bolt cutter to get the proper bite to permit them to cut the chain. It is ideal for securing equipment or portable tools at a job site or for general purpose security use. Sold in full drums or custom cut at the factory to the users required length. H200 Trade size: 7/6 Finish: Blue :.6 Lbs./ per foot package: Custom* H260 Trade size: 7/6 x 400 Finish: Blue : 750 Lbs./ per drum package: Full drum * Custom cut at factory to required length in multiples of foot Hex AntiTheft Chain Lock Padlock body is made from Stainless A304 material with a magnesium shackle. The lock body extends up to protect the shackle from allowing boltcutters to access it. Lock comes with 4 double notch cut reversible keys that can not be removed unless the lock is closed and secure. This lock is a great partner with Hex Chain for maximum security. Hex AntiTheft Chain & Lock Kit Retail packaged kit includes 5 ft. of Hex Chain covered with a 4 ft. protective sleeve and a Stainless Hex Chain Lock. They are all packaged in a convenient nylon storage bag. Each complete kit is individually boxed for attractive retail shelf display. H42000 Shackle length: Finish: Stainless :.60 Lbs./ea. package / H226 Chain length: 5 :.60 Lbs./ea. package: 4 / ctn WARNING: Do not use for overhead lifting. Do not use if chain links or component parts are visibly worn, damaged or distorted. 0 Minimum order quantity: package Catalog weights are approximate

91 HARDWARE Wire & Cable Swedging Tools Cutters / Swedgers / Hammers H Overall length (Inches.) 4 Capacity /6 / cable 2. package Each H /6 3/6 cable 5.50 Each Wire & Cable Cutters * Note: H4420 is SCCʼs premium Swiss cable and wire cutter. It is made with the highest quality Swiss steel available, for up to times longer life than H4420. Overall length (Inches.) Capacity package H /2 Diameter.50 Each H Diameter 5.40 Each H /4 Diameter 2.50 Each H /6 Diameter 0.75 Each H /6 Diameter 0.75 Each Chain & Bolt Cutters Overall length (Inches.) Capacity package H /6 Proof Coil 2.60 Each H H /4 Proof Coil 5/6 Proof Coil Each Each To ols H /6 Proof Coil 7.00 Each Ratchet & Hydraulic Cutters (For display racks) Type Maximum capacity (Inches.) package H H Ratchet Proof Coil. Each H H Hydraulic Hydraulic High Test Transport Each Each H H Mechanics Sledge Hammer HT02 HT03 HT04 HT06 Head Size (Lbs) Handle length package 6 / ctn 6 / ctn 6 / ctn 6 / ctn WARNING: Always wear safety glasses whenever using cutters or hammers. Metal will fly away from tool jaws when cut. The harder the metal, the farther and more forcefully it will fly. To prevent fly away of metal pieces, a cloth rag may be wrapped around the product. FOR CUTTERS: Never exceed the capacity of the cutter both in diameter of material and hardness of the metal. Cable and wire rope should be taped at the cutting point to prevent fraying of the cut end. Special cutters with offset blades designed for cable should always be used to cut GAC or wire rope. Catalog weights are approximate Minimum order quantity: package

92 HARDWARE Heavy Duty Pallet Jack SCCʼs premium, heavy duty pallet jack has a 5,500 Lb. capacity. The wheels are made of durable polyurethane for long life. The forks are a full pallet length of 4 for total load support. The fork rollers allow easy pallet entry and the large ergonomic rubber handle has a three position control lever. This pallet jack has a two year pump warranty and is certified and tested for over 60,000 cycles. 5,500 Lb. (2,500 kgs) capacity Heavy Duty Pallet Jack Full hydraulic system. Bullet connection between steering shaft and pump piston. Convenient to replace rear wheels. Easy to maneuver with a 2 degree turning radius. Special lowering valve to control the rate of decent and over bypass valve for added durability. Total number of pump strokes. Lift per stroke 0.47 (mm). Reliable leakproof hydraulic system. Polyurethane wheel, tandem fork roller. The pump is warranted against leakage for a period of two years. HPT5500 has wider forks for stability. HPT555 has narrower forks to fit smaller pallets. Pallet Jack HPT5500 Description Hand Pallet Truck Single Dimensions A B W L H H2 H3 Ø7. Ø Capacity LBS KGS 5,500 2,500 / Plt Pallet Jack HPT55006 HPT555 HPT5556 Hand Pallet Truck 6 Pack Hand Pallet Truck Single Hand Pallet Truck 6 Pack Ø7. Ø7. Ø7. Ø2. Ø2. Ø ,500 5,500 5,500 2,500 2,500 2,500 6 / Plt / Plt 6 / Plt 2 Year Limited Pump Warranty German Engineered 2 Minimum order quantity: package Catalog weights are approximate

93 HARDWARE Heavy Duty Pallet Jack Heavy Duty Pallet Jack available in two sizes. Effortless pallet entry/exit rollers to make it easier to push and pull the pallet truck. lubrication grease nipples on all moveable parts for easy maintenance. The adjustable pump cap ensures a long service life. Reinforced for added strength and load capacity. Large ergonomic rubber handle with a three way positive control lever. Pallet Jack Replacement Parts (Fits both models) Bushings Roller Chain HPT5500B4 HPT5500B5 : Lbs. / ea. : 3.3 Lbs. / ea. : / pkg : / pkg 2 Year Limited Pump Warranty Nut HPT5500B6 : Lbs. / ea. : / pkg German Engineered Shaft HPT5500B : Lbs. / ea. : / pkg Pallet Jack Copper Washer HPT5500B0 : Lbs. / ea. : / pkg Spring HPT5500B : 3.3 Lbs. / ea. : / pkg Damping Valve Spindle HPT5500B2 : Lbs. / ea. : / pkg Damping Valve Seat HPT5500B3 : Lbs. / ea. : / pkg Spring (.2//22) HPT5500B : Lbs. / ea. : / pkg Dust Covers HPT5500B3 : Lbs. / ea. : / pkg YRing (3.5) HPT5500B4 : Lbs. / ea. : / pkg Dust Ring HPT5500B50 : Lbs. / ea. : / pkg YRing HPT5500B5 : Lbs. / ea. : / pkg Fork Wheels HPT5500B35 : 3.3 Lbs. / ea. : 4 / pkg Large Wheel HPT5500B : Lbs. / ea. : 2 / pkg Bearings HPT5500B : Lbs. / ea. : / pkg Catalog weights are approximate Minimum order quantity: package 3

94 HARDWARE Retail d Chain (In Clamshells) PACKAGE SIZE: (XS) Extra small clamshell: 7 x 4 ½ x ½ Trade size Length (feet) Pkg size package (S) (M) Small clamshell: x 5 ½ x 2 Medium clamshell: x 7 x 2¼ Passing Link Chain (Zinc plated) H0032 2/0 S 3.20 / ctn Trade size Length (feet) Pkg size package Double Loop Chain (Zinc plated) Proof Coil Chain (Zinc plated) H0303 3/6 S 4.00 / ctn H20032 H H /0 #3 # S XS S / ctn / ctn / ctn Twist Link Coil Chain (Zinc plated) Single Jack Chain (Zinc plated) Welde d C hai n H /0 S 3.20 / ctn H22033 H # #6 25 XS XS / ctn / ctn Twist Link Machine Chain (Zinc plated) H06032 H /0 #4 S S / ctn / ctn Sash Chain (Zinc plated) H #35 XS 0.0 / ctn Straight Link Machine Chain (Zinc plated) H /0 XS 3.30 / ctn 4 Trailer Safety Chain w/latch Hooks (Zinc plated) H #4 XS.30 / ctn H /6 4 S 2.30 / ctn H20304 /4 4 M 3.40 / ctn Straight Link Coil Chain (Zinc plated) H0032 2/0 S 2.0 / ctn H00324 #4 XS.20 / ctn 4 Minimum order quantity: package Catalog weights are approximate

95 HARDWARE Retail d Chain Accessories (Skin Carded) PACKAGE SIZE: (S) Small Card: 3 x 5 ½ (L) Large Card: 4 ¼ x 7 (XL) Extra Large Card: 5 ¼ x ½ Trade size Items (card) Card size Aluminum Sleeves & Stops H300004C H30004C H300024C H300034C H300044C H C H C /6 3/32 / 3/6 / S S S S S (Lbs/ctn) Wire Rope Clip Kit (Zinc plated) H C H C H C H C H C / 3/6 /4 5/6 package crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn Clevis Grab Hooks G70 (Yellow zinc plated) 5/ S L L L L Snaps (Nickel or Zinc plated) H60260C H6026C H60265C H60266C H60267C H6026C H6026C H60262C 4 / / 3 3 /6 4 2 /6 4 3/6 S S S S S S L L L XL Clevis Slip Hooks G43 (Zinc plated) H742604C H742605C H742606C Clevis Grab Hooks G43 (Zinc plated) H762604C H762605C H762606C /4 5/6 /4 5/6 L L XL L L XL crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn Trade size Items (card) Quick Links (Zinc plated) H22602C H22603C H22604C H22605C H22606C / 3/6 /4 5/6 2 Card size Repair Lap Links (Zinc plated) H02C H022C H025C H02C 3/6 /4 5/6 2 Cold Shuts (Zinc plated) H603C H604C H605C S S S S S S S S S Connecting Links (Zinc plated) H32603C H32604C H32605C H32606C (Lbs/ctn) package crds / ctn crds / ctn 5 crds / ctn 5 crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn Screw Pin Anchor Shackels (Zinc plated) H62603C H62604C H62605C H62606C 3/6 /4 5/6 S S S L Snap Pear Hooks (Zinc plated) H72603C H72604C H72605C H72606C 3/6 /4 5/6 3/6 /4 5/ S Hooks (Zinc plated) H4235C H4236C H4237C 3/6 /4 5/6 #40 #60 # S S S S S S S S S L S S S S Double Clevis G43 (Zinc plated) H52640C /4 5/6 H52606C S S crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn crds / ctn Retail Packaging Catalog weights are approximate Minimum order quantity: package 5

96 HARDWARE H Chain Assortment Welded Chain, Reel & Accessory Assortment Display rack & chain assortment with 5 reels of welded chain. Assortment features a free standing retail display unit and can be purchased with or without a cutter. Item Trade size Description Reel width Finish Assort. qty Assort. weight/lbs H0703 H0704 H0705 H0706 H0072 H H5000 H500 H H /6 x 0 /4 x 75 5/6 x 70 x 45 2/0 x 5 Proof coil reel Proof coil reel Proof coil reel Proof coil reel Straight link coil reel Ratchet style welded chain cutter Display rack Axle kit and header sign Complete rack & assort. listed above Complete rack & assort. w/o cutter lbs lbs H00000 Fitting Assortment Displays Chain fitting and bin merchandiser with 2 different chain accessories. Assortment features a free standing retail display unit and 2 bins for parts. Item H H H H H H H02 H022 H025 H02 H22603 H22604 H22605 H22606 H4237 H423 H52606 H52640 H72604 H72605 H72606 H H H5000 H5002 H00000 Trade size /4 5/6 /4 5/6 3/6 /4 5/6 3/6 /4 5/6 #0 #0 /4 5/6 /4 5/6 Description Clevis slip hooks Clevis slip hooks Clevis slip hooks Clevis grab hooks Clevis grab hooks Clevis grab hooks Repair lap links Repair lap links Repair lap links Repair lap links Quick links Quick links Quick links Quick links S Hooks S Hooks Double clevis Double clevis Snap pear hooks Snap pear hooks Snap pear hooks Small plastic bins Large plastic bins Display rack Bin kit and header sign Complete rack & assortment listed Finish Assort. qty Assort. weight/lbs lbs H00000 H Each rack measures: 6 Wide, 5 High, Deep Assortment can be customized 6 Minimum order quantity: package Catalog weights are approximate

97 HARDWARE H Chain Assortment Item Trade size 2/0 x 75 #3 x 200 # x 0 #35 x 0 /0 x 200 #6 x 250 / x 250 3/0 x 5 /0 x 200 Weldless Chain, Reel & Accessory Assortments Display rack & weldless chain assortment with reels of weldless chain. Assortment features a free standing retail display unit and can be purchased with or without a cutter. H20072 H20025 H2203 H24034 H H20033 H402 H2722 H H H5000 H500 H H Description Double loop reel Double loop reel Single jack reel Steel sash reel Brass safety reel Single jack reel Coated aircraft cable reel Lock link reel Double loop reel Weldless chain cutter Display rack Axle kit and header sign Complete rack & assortment Complete rack & assort. w/o cutter Reel width Finish Assort. qty Assort. weight/lbs lbs 7.00 lbs H00000 Fitting Assortment Chain fitting and bin merchandiser with 2 different chain accessories. Assortment features a free standing retail display unit and 2 bins for parts. Item H H60260 H6026 H60265 H60266 H60267 H6026 H6026 H60262 H H22602 H22603 H22604 H22605 H4227 H4234 H4235 H4236 H72602 H72603 H72604 H H H5000 H5002 H00000 Trade size 3/ /6 2 7/ 3 3 3/4 4 3/4 4 /2 /4 / 3/6 /4 5/6 #20 #30 #40 #60 / 3/6 /4 Description Wire rope clips Rigid open eye bolt Swivel round eye spring snap Swivel round eye spring snap Swivel open eye spring snap Swivel open eye spring snap Swivel eye bolt snap Swivel eye animal tie snap Double end bolt snap Forged hook & eye turnbuckle Quick links Quick links Quick links Quick links S Hooks S Hooks S Hooks S Hooks Snap pear hooks Snap pear hooks Snap pear hooks Small plastic bins Large plastic bins Display rack Bin kit and header card Complete rack & assortment listed Finish NKL NKL NKL NKL NKL NKL NKL HDG Red Red Assort. qty Assort. weight/lbs lbs H00000 H Each rack measures: 6 Wide, 5 High, Deep Assortment can be customized Catalog weights are approximate Minimum order quantity: package 7 Displays

98 HARDWARE Welded Chain Pail / Reel & Accessory Assortment H Chain & Fittings Assortment Display rack & welded chain assortment with 6 pails and different chain accessories. Assortment can be purchased with or without a cutter. Item Trade size Description Finish Assort. qty Assort. weight/lbs H003 3/6 x 250 Proof coil pail H004 /4 x 4 Proof coil pail H005 5/6 x 2 Proof coil pail H006 x 63 Proof coil pail H02 2/0 x 350 Straight link coil pail H02 2/0 x 300 Passing link pail.00 7 H /4 Clevis slip hooks 5.00 H /6 Clevis slip hooks 6.0 H Clevis slip hooks 3.00 H /4 Clevis grab hooks 4.00 H /6 Clevis grab hooks 7. H Clevis grab hooks.0 3 H02 3/6 Repair lap links H022 /4 Repair lap links H025 5/6 Repair lap links Displays 6 7 H02 H22604 /4 Repair lap links Quick links H /6 Quick links H22606 H52640 /4 5/6 Quick links Double Clevis Rack measures: 2 Wide, 6 High, 24 Deep 2 22 H72603 H /6 /4 Snap pear hooks Snap pear hooks Assortment can be customized 23 H /6 Snap pear hooks H72606 Snap pear hooks H H H500 H Ratchet style welded chain cutter Additional small plastic bins Additional bin rail Display rack with bins SCC s MOST POPULAR freestanding merchandiser H Complete rack & assortment listed above lbs H Complete rack & assortment w/o cutter lbs Minimum order quantity: package Catalog weights are approximate

99 HARDWARE Welded Chain Pail / Reel & Accessory Assortment H Chain & Fittings Assortment Display rack & welded chain assortment with 4 pails & 2 reels of welded chain. Also includes different chain accessories. Assortment can be purchased with or without a cutter. Item Trade size Description Finish Assort. qty Assort. weight/lbs H003 3/6 x 250 Proof coil pail H004 /4 x 4 Proof coil pail H005 5/6 x 2 Proof coil pail H006 x 63 Proof coil pail H0072 2/0 x 5 Straight link coil reel H0072 2/0 x 50 Passing link reel H /4 Clevis slip hooks 5.00 H /6 Clevis slip hooks 6.0 H Clevis slip hooks 3.00 H /4 Clevis grab hooks 4.00 H /6 Clevis grab hooks 7. H Clevis grab hooks.0 3 H022 /4 Repair lap links H025 5/6 Repair lap links H02 Repair lap links H22604 H22605 H22606 /4 5/6 Quick links Quick links Quick links Displays 20 H H Ratchet style welded chain cutter Display Rack with bins Rack measures: 2 Wide, 6 High, 24 Deep H Full rack/assortment listed above lbs Assortment can be customized H Full rack/assortment w/o cutter lbs CREATE CUSTOM RETAIL DISPLAY UNITS: Pail stackers are available for creating a display using round 5 gal. pails on an existing gondola. EZ Load pail stackers (Boxed and sold in pairs) H500 Finish: Bright zinc Shipping : 2.00 Lbs./pr. : pair / carton Order Unit: pair + = Catalog weights are approximate Minimum order quantity: package

100

101 Section 4 Cable Chain Traction Products ZCable Products... 2 ZProduct Information ZChain Super Z Super Z Shur Grip Z... Super Z LT... Super Z Single... Super Z Dual/Triple & OTR LadderStyle Cable Products... 3 Radial Chain... Radial Chain LT... TA Truck Singles... 3 TA Truck Duals... 3

102 TRACTION PRODUCTS What is so important about a Z? For over a decade SCC has been selling a unique group of products under various "Z" trademarks. The "Z" was inspired by the Zshaped crossmember pattern, but what the Z really stands for is reliability, performance, convenience and durability. SCC is the first and only traction product company to combine the advantages of diagonal crossmembers, steel traction coils and a method of fastening and adjusting the "chain" so that there is no loss of traction at any point on the tire and often no need to readjust the product after the initial installation. SCCʼs patented Z products have these important advantages over other winter traction products: Easier installation and removal. Greater durability and lower potential for vehicle damage. Superior starting, stopping and cornering performance. Lower operating space requirements around drive tires. Greater compatibility with electronic Traction Management Systems (ABS, 4WD & AWD). SCC has a "Z" traction product for every winter traction need: ZCHAIN for police, fire, ambulance as well as other highperformance users. Available to fit most car, pickup and SUV tire sizes. SUPER Z LT with the same advantages as SHUR GRIP Z, but designed for use on pickups and SUVs. SUPER Z6, our newest product for cars, pickups and SUVs able to operate in drive tire clearances as low as 6 mm (/4 ). SHUR GRIP Z for simple installation and excellent durability on passenger car tires. SUPER Z for commercial trucks, buses, graders and other industrial applications. Available in single, widebase (super single) and dualtire versions. SUPER Z, our newest product for new, larger SUV tires and small to medium commercial vehicles able to operate in drive tire clearances as low as mm (5/6 ). SCC's "Z" products are easily the most recognized in the traction industry. Theyʼre aggressive, easier to use and longerlasting than other traction products, and they have proven it from California to Bosnia. For more information, see pages 4. Cable Chain S.A.E. J320 DEFINITION: Most newer vehicles manufactured since the late 0ʼs will have special clearance requirements. This generally refers to S.A.E. Class S clearance restrictions. SCCʼs Z family of traction products for passenger cars and light duty trucks will meet or exceed these requirements. Y Y X The minimum clearances specified must be maintained around fenders, braces, suspension parts, strut housing, splash pans and fuel and brake lines. Tire size must be known to select a traction product of correct fit. For passenger car, pickup and SUV applications it is important to check the ownerʼs manual. The restricted wheel well clearances in most of todayʼs vehicles will require Class S products. Consumers must refer to their ownerʼs manual for information pertaining to their specific vehicle. SIDEWALL MINIMUM CLEARANCE TREADFACE MINIMUM CLEARANCE X 2

103 TRACTION PRODUCTS CLEARANCE DEFINITIONS: Class S is the Society of Automotive Engineersʼ (SAE) definition for the least amount of space that should be provided around the drive tires of any vehicle to accommodate the use of a winter traction product. These different classes incorporate two different measurements: from the tread face of the tire to the nearest obstruction, and from the inside sidewall of the tire to the nearest obstruction. S.A.E. CLASS S Cable chains or link chains for vehicles with restricted clearances. S.A.E. CLASS U Passenger tire chains that use light truck components, as well as some light truck chains. S.A.E. CLASS W Regular tire chains for vehicles with nonrestricted wheel well clearances. ILLUSTRATION OF S.A.E. CLEARANCE REQUIREMENTS & SCC PRODUCT COMPARISON QUIK GRIP LINK CHAIN PROFILE TYPE P, RP Treadface:.7 / 50mm (X) Sidewall: 0. / 23mm (Y) Class U CLASS S LINK TYPE PL, WHITESTAR ALLOY, ZCHAIN, SUPER Z LT, SUPER Z AND ALL PRODUCTS LISTED BELOW Treadface:.46 / 37mm (X) Sidewall: 0.5 / 5mm (Y) Class S SCC RADIAL CHAIN & SHUR GRIP Z Treadface:.00 / 25mm (X) Sidewall: 0.50 /.7mm (Y) SCC SUPER Z6 Treadface:.20 / 3mm (X) Sidewall: 0.25 / 6.3mm (Y) SCC PRODUCT CLEARANCE SPECIFICATIONS: As you can see by the measurements shown below, many SCC products fit in an even smaller space than required by S.A.E. Class S. Class S requires 5mm (0.5 ) clearance from the sidewall and 37mm (.46 ) clearance from the treadface. SCC PRODUCTS THAT MEET CLASS S REQUIREMENTS ZChain (Z53 Z53); Super Z LT (ZT72ZT75); Whitestar Alloy (WS604WS707); Quik Grip (QG4QG42) SCC PRODUCTS THAT EXCEED CLASS S REQUIREMENTS (operate in low clearance areas around the sidewall and the treadface) Cable Chain Super Z6 (SZSZ45) Requires 6.3 mm (0.25 ) clearance from the sidewall Requires 3.0 mm (.20 ) clearance at the treadface Super Z (SZ462SZ47) Requires.2 mm (0.32 ) clearance from the sidewall Requires 35.0 mm (.3 ) clearance at the treadface Shur Grip Z (SZ35SZ343); Radial Cable Chain (SC4SC42); Requires.7 mm (0.50 ) clearance from the sidewall Requires 25.0 mm (.00 ) clearance at the treadface 3

104 TRACTION PRODUCTS The choice of professional fleets everywhere Meets S.A.E. Class S clearance requirements for both passenger cars and light trucks. Over the past decade Z Chain has become the winter traction product of choice for police, fire, ambulance and other professional fleets throughout North America. Z Chainʼs fast installation, aggressive traction performance and extreme durability simply out class all other options. Manganese alloy crossmembers which offer superior all around traction performance Operates within the space limitations of Class S clearance requirements, even in light truck sizes. Cable Chain Fast, secure installation and removal. Z Chain doesnʼt require chain tighteners, so it is the perfect choice for customers with alloy or protruding wheels and wheel covers as chain tighteners can scratch these types of wheels. Low potential for damage to vehicle body and mechanical components, even when abused. Included with each pair of chains: Clear, illustrated step by step installation and removal instructions and gloves all in a durable, re usable nylon bag. U.S. Patent #: 5,2,63 4

105 TRACTION PRODUCTS U.S. Patent #: 5,2,63 Extreme performance for high end and professional applications Z Chain is based on SCCʼs revolutionary patented Z design. Product updates made over the last few years have kept Z Chain as the premier cable traction product, both in performance and durability. The unique fastening system reduces fly off, provides less road impact and greatly extends the life of the chain. Z Chain was originally designed for police departments and emergency fleets, but with Z Chainʼs high performance features, skiers and other demanding users have found Z Chain to be the best winter traction product available Z Chainʼs diagonal cross member pattern provides: Constant contact between the tire and road surface. Greater lateral traction for improved cornering and braking, in addition to starting and stopping traction. Maximum efficiency of anti lock brakes (ABS), all wheel drive (AWD) and other computer assisted traction/braking systems. Chain tighteners SHOULD NOT be used. Outside fastener ZChain (Passenger & light truck) Inside fastener Diagonal Crossmember ü Meets S.A.E. Class S Requirements Z53 Z547 Z555 vpartial listing of tire sizes 5/555, 5/605, 5/654, 5/655, 5/506, 5/555, 5/556, 5/605, 205/456, 205/506 5/655, 205/507, 205/556, 205/606, 205/655, 25/457, 25/45, 25/507, 25/556, 225/40 205/755, 25/557, 25/606, 25/656, 25/705, 225/45, 225/507, 225/557, 225/606, 245/40 per pair (Lbs.) Replacement Crossmember Z30 Z34 Z3 Cable Chain Z563 25/607, 25/657, 25/706, 225/607, 225/656, 225/705, 235/50, 235/557, 235/656, 255/45.00 Z3 Z57 25/55, 225/60, 225/756, LT225/756, 235/60, 235/657, 235/706, 235/755, 255/55, 255/ Z30 Z /65, 245/60, 245/657, 245/706, 245/707, LT245/707, 245/756, LT245/756, 255/4520, 255/ Z34 Z57 235/757, 255/5020, 265/60, 265/657, 265/706, 265/707, LT265/707, 265/756, LT265/756, 275/65.50 Z34 Z53 LT255/757, 265/70, 275/5520, 275/6020, LT275/6520, 275/70, LT275/70, 25/4522, 25/707, LT25/707 d: pair per bag / 4 pair per master carton 3.00 Z3 Order unit: Pair vthis is only a partial listing of tire size applications. For complete, up to date listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit chain.com. Refer to vehicle ownerʼs manual for any traction product limitations. Catalog weights are approximate Minimum order quantity: Master carton 5

106 TRACTION PRODUCTS & TM Big traction in a small space Z performance for vehicles with VERY limited operating clearance around the drive tires Super Z6 and Super Z are based on our Shur Grip Z and Super Z ideas, but with a couple of important differences. Super Z6 is the only steel traction product that can operate in drive tire clearances as low as 6 mm (/4 ) Super Z is the only steel traction product that can operate on many new larger SUV tires and small to mediumsized commercial vehicles with drive tire clearances as low as mm (5/6 ) Both are even stronger and more durable than either Shur Grip Z or Super Z LT Easy installation and removal with superb durability. Aggressive starting, stopping and cornering traction. Cable Chain Greater compatibility with electronic Traction Management Systems (ABS, 4WD & AWD). Inside fastener Outside fastener Automotive designers are constantly trying to build vehicles with larger and more comfortable interior spaces and commercial vehicle designers are trying to make room for a larger payload. The easiest way to do this would just be to make bigger vehicles, but there are legal and practical limits on just how big they can get So, clever designers first try to make sure thereʼs no existing space thatʼs not being used like the space around a vehicleʼs tires. In fact, designers have become so good at finding other uses for this space that there are now hundreds of vehicle models whose ownerʼs manuals warn donʼt use tire chains or words to that effect. Included with each pair of chains: Clear, illustrated stepbystep installation and removal instructions, plastic gloves and one pair of rubber tensioners all in a durable, reusable nylon bag. 6

107 TRACTION PRODUCTS TM & The choice for very limited clearance applications Limited clearance presents a problem for those who own these vehicles and who also need to use winter traction products, but SCC is proud to announce that the problem is solved Super Z6 and Super Z are made for these vehicles designed to operate in the smallest possible space and designed to have all the other Z product advantages. Chain tighteners ARE required and included. Super Z6 (Passenger, Pickup & SUV) SZ U.S. Patent # 7,00,674; China Patent #: ZL ; Europe and Japan Patents Pending vpartial listing of tire sizes 65/705, 65/03, 65/04, 75/556, 75/655, 75/704, 5/555, 5/604, 5/654, 5/604 ü Meets S.A.E. Class S Requirements per pair (Lbs.).00 SZ3 SZ7 SZ SZ3 SZ33 SZ35 SZ37 SZ3 SZ43 SZ42 SZ435 SZ44 SZ447 5/605, 5/655, 5/704, 5/754, 5/506, 5/555, 5/556, 205/456, 25/456, 225/35 5/605, 5/704, 205/40, 205/457, 205/506, 205/555, 25/40, 225/554, 225/604, 245/406 5/606, 5/655, 5/656, 5/705, 5/705C,5/754, 205/605, 205/606, 205/655, 25/45 5/755, 205/507, 205/556, 25/407, 25/556, 25/654, 225/506, 245/35, 245/407, 245/505 25/457, 25/507, 25/555, 25/605, 225/407, 225/40, 225/456, 225/457, 225/555, 225/ /705, 205/706, 205/755, 25/557, 25/606, 25/656, 25/705, 225/50, 235/507, 255/35 225/45, 225/507, 225/556, 235/35, 235/40, 235/457, 235/506, 235/604, 245/457, 255/407 25/607, 25/657, 25/706, 225/557, 225/606, 225/607, 225/656, 225/705, 235/45, 245/40 225/657, 225/706, 225/755, 235/50, 235/557, 235/55, 235/607, 235/656, 255/45, 275/35 LT25/56, 225/60, 225/756, LT225/756, 235/60, 235/657, 235/706, 235/755, 245/4520, 255/ /65, 245/5020, 245/60, 245/657, 245/706, 245/707, LT245/707, 255/5020, 255/657, 255/706 3x.505LT, 245/756, LT245/756, 245/757, LT245/757, 265/60, 265/657, 265/706, 265/755, 275/4520 LT235/07, 255/502, 255/707, 255/70, 265/5020, 265/65, 275/4522, 275/60, LT275/707, 35/ SZ45 265/707, LT265/707, 265/70, 265/756, LT265/756, 275/5520, 275/6020, LT275/65, 275/65, 25/60.50 d: pair per bag / 4 pair per master carton Order unit: Pair Super Z (Larger SUVs, small and medium commercial vehicles under 20,000 GVW) ü Meets S.A.E. Class S Requirements SZ462 SZ46 SZ474 vpartial listing of tire sizes 245/70.5, 255/70.5, LT275/6520, 275/70, LT275/70, 275/75, 25/707, LT25/707, LT25/756, LT25/ TR,.57.5, 265/70.5, 265/75, LT265/56, 25/5520, 25/65, 305/3524, LT305/706, LT305/756 33x.505LT, 33x.506, 33x.507, 33x.50, 33x.5020, 25/707, 305/60, LT305/657, 35/706, 325/5020 per pair (Lbs.) Cable Chain SZ40 33x3.505LT, 36x45LT, 36x4.505LT, 36x LT, 36x5.505LT, 355/ SZ46.005TR, 7.5, 245/7022.5, 25/70.5, 25/75, 305/707, 35/707, 35/756, 35/757, 325/ SZ , 22.5, 37x.506.5LT, 37x.507, 235/022.5, 245/7522.5, 245/022.5, 255/7522.5, 25/757.5, LT35/ SZ47 7.5, 37x.505LT, 225/7022.5, 255/7022.5, 265/75.5, 275/70.5, 25/70.5, LT305/56 d: pair per bag / 2 pair per master carton.75 Order unit: Pair vthis is only a partial listing of tire size applications. For complete, up to date listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit chain.com. Refer to vehicle ownerʼs manual for any traction product limitations. Catalog weights are approximate Minimum order quantity: Master carton 7

108 TRACTION PRODUCTS U.S. Patent #: 5,2,63 Z Performance at a moderate price. Shur Grip Z is a patented SCC product that is designed to meet the traction product needs of the everyday consumer and is available to fit most passenger car tire sizes. Shur Grip Z is typically merchandised using SCCʼs unique display tire and stand, offering potential buyers an opportunity to see the product and to try its installation system before buying. Shur Grip Z offers a unique combination of performance and convenience features for every user. The fastest, easiest installation of any traction product, with included rubber tighteners. Better all around traction performance than conventional cable or link tire chains. Traction coils provide greater durability than conventional cable or link tire chains. Better compatibility with anti lock brakes, traction control, all wheel drive and other electronically monitored control systems. Meets the requirements of S.A.E Class S operating clearances. Low potential for damage to vehicle body and mechanical components, even when abused. Inside fastener Chain tighteners ARE required and included. Shur Grip Z (Passenger) ü Meets S.A.E. Class S Requirements Cable Chain SZ35 SZ3 SZ323 SZ327 vpartial listing of tire sizes 45/655, 55/03, 65/654, 65/704, 65/70360, 65/753, 75/654, 75/703, 5/554, 5/553 65/705, 65/03, 65/04, 75/556, 75/655, 75/704, 5/555, 5/604, 5/654, 5/604 5/605, 5/655, 5/704, 5/506, 5/555, 5/556, 5/703, 205/456, 25/456, 225/35 5/605, 5/704, 205/40, 205/457, 205/506, 205/555, 25/40, 25/555, 225/554, 245/406 per pair (Lbs.) Replacement Crossmember SZ334 SZ336 SZ33 SZ33 SZ32 5/606, 5/655, 5/656, 5/705, 5/705C, 5/754, 205/605, 205/606, 205/655, 25/45.00 SZ33 SZ33 5/755, 205/507, 205/556, 25/407, 25/507, 25/556, 25/605, 225/506, 245/35, 245/ SZ340 SZ /705, 205/755, 25/557, 25/606, 25/656, 25/705, 225/507, 225/50, 225/556, 235/507. SZ342 SZ33 25/607, 25/657, 25/706, 225/557, 225/606, 225/607, 225/656, 225/705, 235/45, 245/40.0 SZ342 SZ /657, 225/706, 235/45, 235/50, 235/557, 235/607, 235/656, 245/50, 255/40, 255/45 d: pair per box / 6 pair per master carton. SZ344 Order unit: Pair vthis is only a partial listing of tire size applications. For complete, up to date listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit chain.com. Refer to vehicle ownerʼs manual for any traction product limitations. Minimum order quantity: Master carton Catalog weights are approximate

109 TRACTION PRODUCTS U.S. Patent #: 5,2,63 Z Performance for light trucks, SUVs and 4x4s at a moderate price. Super Z LT (ZT700 Series) is Shur Grip Z's companion product for sport utility vehicles and pickups. The patented design is the same as Shur Grip Z, but features larger and tougher components. Like Shur Grip Z, Super Z LT also features a "designed in" rubber tightener so there is no need to stop and retighten. Super Z LT covers the majority of light truck tires with only five stock numbers. Super Z LT offers the same performance features as Shur Grip Z: Fastest, easiest installation of any traction product with included rubber tighteners. Super Z LT meets Class "S" clearance requirements for vehicles with limited or low clearance. Better compatibility with anti lock brakes, traction control, all wheel drive and other electronically monitored control systems. Super Z LT's plastic package includes a pair of rubber tighteners, step by step installation & removal instructions and waterproof gloves. Chain tighteners ARE required and included. Super Z LT (Pickup & SUV) ü Meets S.A.E. Class S Requirements ZT72 vpartial listing of tire sizes LT25/56, 225/60, 225/756, LT225/756, 235/60, 235/657, 235/706, 235/755, 245/4520, 255/4520 per pair (Lbs.) 3.25 Replacement Crossmember ZT742 ZT /65, 245/5020, 245/60, 245/657, 245/706, 245/707, LT245/707, 255/5020, 255/657, 255/ ZT742 ZT74 3x.505LT, 245/756, LT245/756, 245/757, LT245/757, 265/60, 265/657, 265/706, 265/755, 275/ ZT744 ZT747 LT235/07, 255/502, 255/707, 255/70, 265/5020, 265/65, 275/4522, 275/60, LT275/707, 35/ ZT746 ZT75 LT255/757, 265/707, LT265/707, 265/70, 265/756, LT265/756, 275/5520, 275/6020, LT275/65, 275/65 d: pair per box / 4 pair per master carton 4.50 ZT746 Order unit: Pair vthis is only a partial listing of tire size applications. For complete, up to date listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit chain.com. Refer to vehicle ownerʼs manual for any traction product limitations. IMPORTANT INFORMATION FOR PICKUPS, SUVs & 4x4s: Many western states and Canadian provinces have mountain passes and roadways where the possession and use of winter traction devices are required by law, regardless of vehicle type, under certain winter conditions. A failure to comply with these requirements can result in fines and/or other penalties imposed by local authorities. For current, up to date information regarding chain laws, restrictions and regulations, as well as the most complete tire size application listing, refer to SCCʼs Winter Traction Tech Guide and Tire Size Directory or visit chain.com Many pickups and sport utility vehicles have restricted clearances around the drive tires. Vehicle manufacturers recommend using only traction products that meet S.A.E Class S clearance specifications. Super Z6, Super Z, Super Z LT & Z Chain are the only SCC light truck cable brands that meet these requirements. Traditional link chain will not meet the minimum clearance requirements. Cable Chain CAUTION: When chaining up one axle of a four wheel drive vehicle, always check the owner s manual for the manufacturers recommendation as to which axle to chain up. Catalog weights are approximate Minimum order quantity: Master carton

110 TRACTION PRODUCTS U.S. Patent #: 5,2,63 Extreme Z performance for commercial & OTR applications Super Z is designed with commercial users in mind. Super Z comes in sizes to fit commercial highway and traction tires, as well as many specialized tire applications. Manganese Alloy traction coils (0.67 diameter) give superior traction performance compared to conventional cable or link tire chains. Greater durability and weight savings of at least 20% compared to conventional link tire chains. Approved by CalTrans under minimum chain up requirements over I 0 at Donner Pass. Superior compatibility with anti lock brakes and other electronically monitored control systems. Low potential for damage to vehicle body and mechanical components, even when abused. Fast, easy installation, in comparison to any other winter traction product for trucks or buses. Chain tighteners ARE required and included. Inside fastener Cable Chain Super Z (Truck single) * * * * * ZT35 ZT37 ZT4 ZT53 ZT5 ZT65 ZT6 ZT77 ZT ZT7 ZT ZT2 ZT6 ZT7 ZT ZT per pair vpartial listing of tire sizes (Lbs.) 245/70.5, 255/70.5, LT255/56, 265/6520, 275/70, LT275/70, 275/75, LT25/756, LT25/ TR, 32x.505LT, 265/70.5, 265/75.5, LT265/56, 275/70.5, 25/65, LT305/706, LT305/ , 33x.506, 33x.507, 33x.50, 33x.5020, 25/707, 305/60, LT305/657, 35/ TR, 7.5, 245/7022.5, 25/70.5, 25/70.5, 25/75, LT305/56, 35/707, 35/756, 35/ , 22.5, 235/022.5, 245/7522.5, 245/022.5, 255/7022.5, 255/7522.5, 25/757.5, LT35/ , , 255/022.5, 265/7522.5, 35/ , 22.5, 275/7022.5, 25/ /020, 275/7522.5, 25/7522.5, 25/ , 2.5, 275/022.5, 275/024.5, 25/7024.5, 25/7524.5, 25/024.5, 25/7522.5, 25/7524.5, 25/ ,.0020, 4.5,.5020, 22.5,.522.5, 305/7524.5, 35/022.5, 320/ ,.0024,.0020,.524.5, , /020, 305/522.5, 365/7022.5, 365/020, 35/6522.5, 400/ , 425/5522.5, 425/6522.5, 445/ / /520, 425/ / NOTE: These tire sizes are also available in Super Z style, see pg. 7 d: pair per box / 2 pair per master carton * Replacement Crossmember ZT25 ZT26 ZT26 ZT263 ZT263 ZT263 ZT263 ZT265 ZT263 ZT265 ZT267 ZT267 ZT275 ZT26 ZT23 ZT277 Order unit: Pair v This is only a partial listing of tire size applications. For complete, up to date listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit chain.com. Minimum order quantity: Master carton Catalog weights are approximate

111 TRACTION PRODUCTS Super Z OTR (Singles for commercial and OTR applications) Chain tighteners ARE required and included. ZT 445/ vpartial listing of tire sizes per pair (Lbs.) 5.00 Replacement Crossmember ZT265 ZT32.432, GRADER, GRADER, 35/ ZT532 ZT GRADER, GRADER ZT54 ZT GRADER, GRADER, 445/ ZT543 ZT , 40/7034, 505/525, 520/ ZT545 d: /2 pair per box / pair per master carton Order unit: Pair Dual/Triple with QuikDraw tensioning Extreme performance for dual/triple applications U.S. Patent #: 6,725,4 Super Zʼs patented QuikDraw tensioning eliminates the need for any tightening tools or additional tensioners. Its one piece design allows for fast, easy installation. Chain tighteners SHOULD NOT be used. Manganese Alloy traction coils (0.67 diameter) give superior traction performance. Greater durability and weight savings of at least 30% compared to conventional link tire chains. Superior compatibility with anti lock brakes and other electronically monitored control systems. Low potential for damage to vehicle body and mechanical components, even when abused. QuikDraw center rail tensioner Outside fastener Inside fastener Super Z Dual/Triple (with QuikDraw Tensioning) vpartial listing of tire sizes ZT4.255,.005TR, 7.5, 7.5, 265/75.5, 275/70.5, 25/70.5, 25/75 per pair (Lbs.) Replacement Crossmember ZT32 Cable Chain ZT , 22.5,.005TR, 225/022.5, 235/022.5, 245/7522.5, 245/022.5, 255/7022.5, 255/7522.5, 275/ ZT33 ZT ,.2520, , 22.5, 255/022.5, 265/7522.5, 275/7522.5, 25/ ZT34 ZT , 22.5,.00/020, 275/022.5, 25/7024.5, 25/7522.5, 35/ ZT35 ZT2.0020, 2.5, 275/024.5, 25/7524.5, 25/024.5, 25/7524.5, 25/022.5, 305/7524.5, 305/022.5, 35/ ZT35 ZT0.0022,.0020, 4.5,.5020, 22.5,.522.5, , 305/522.5, 35/022.5, 320/ ZT36 d: /2 pair per box / pair per master carton Order unit: Pair v This is only a partial listing of tire size applications. For complete, up to date listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit chain.com. Catalog weights are approximate Minimum order quantity: Master carton

112 TRACTION PRODUCTS The original cable chain for cars & light trucks Radial Chain was originally conceived to save sidewall wear on radial tires and was the first brand name in cable chain winter traction products. Its consumer friendly features caused a revolution in winter traction, and itʼs still recognized as a market leader. SCCʼs Radial Chain LT is todayʼs basic product for the pickup, van & recreational vehicle market. Radial Chain LT can be installed in minutes and removed easily. Radial Chain and Radial Chain LT utilize an allmetal fastening system. Chain tighteners SHOULD NOT be used. Simple mounting and removal due to its low weight. Improved starting, stopping and cornering performance. Allsteel construction for long service life and smooth ride. Low operating space requirements around drive tires for passenger sizes. Radial Chain (Passenger) SC4 Partial listing of tire sizes 45/655, 55/605, 55/0, 55/03, 65/505, 65/604, 65/653, 65/654, 65/703, 65/753 Meets S.A.E. Class S Requirements per pair (Lbs.) 4.40 SC SC22 SC26 SC30 SC32 SC34 SC36 SC3 555, 653, 65/655, 65/704, 65/705, 65/70360, 65/70365, 65/754, 65/03, 65/ LT, 7.003, 655, 65/05, 75/756 75/655, 5/605, 5/654, 5/655, 5/65365, 5/704, 5/505, 5/506, 5/604, 5/703 5/754, 5/755, 5/556, 5/605, 5/606, 5/655, 5/656, 5/704, 5/705, 5/ /506, 205/507, 205/556, 205/605, 205/606, 205/655, 25/40, 25/457, 25/507, 25/556 5/755, 25/605, 5/705C, 25/655, 25/606, 205/705, 205/656, 205/755, 205/706, 25/ /40, 225/457, 225/45, 225/507, 225/50, 225/556, 245/407, 245/40, 245/457, 265/40 25/607, 25/656, 25/657, 25/705, 25/706, 225/557, 225/606, 225/607, 225/656, 225/ Cable Chain SC40 235/45, 235/507, 235/50, 235/557, 235/606, 235/607, 235/656, 245/45, 245/50, 255/ SC42 225/657, 225/706, 235/45, 235/7460A, 245/45, 245/60460A, 255/40, 255/45, 255/45, 255/50.70 d: pair per box / 6 pair per master carton Order unit: Pair Radial Chain LT (Light truck) DOES NOT Meet S.A.E. Class S Requirements TC2MM TC22MM TC25MM Partial Listing of tire sizes 225/55, 225/60, 225/657, 225/706, 225/756, LT225/756, 235/55, 235/657, 235/706, 235/755 LT25/56, LT225/757, 235/60, 235/707, 235/756, 235/757, 245/50, 245/657, 245/707, LT245/707 3x.505LT, LT235/07, 245/756, LT245/756, 245/757, LT245/757, LT255/757, 265/707, 265/756, LT265/756 per pair (Lbs.) d: pair per box / 4 pair per master carton Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Refer to vehicle ownerʼs manual for any traction product limitations. Minimum order quantity: Master carton Catalog weights are approximate

113 TRACTION PRODUCTS U.S. Patent #: 5,2,63 Alloy Radial Chain is SCCʼs updated ladder style cable chain for commercial applications. TA Alloy Radial Chain is a familiar looking product with a few unique features. Manganese Alloy traction coils (0.525 diameter) provide superior traction, durability and weight savings of at least 50% compared to conventional link tire chains. The crossmember eyelets allow for easy replacement of worn crossmembers without any special tools. For fleet use, a repair tool kit is available (see pg.50). Features a quick and easy linkstyle fastening system with an overcenter latch for easier installation and adjustment. Alloy Radial Chainʼs package for single and dual applications includes illustrated installation and removal instructions. Outside fastener Inside fastener Alloy Radial Chain (Truck singles) Partial listing of tire sizes TA3.2520, 22.5, 37x.505LT, 235/022.5, 245/022.5, 255/7022.5, 255/ TA4.0020, 22.5 TA43 275/7522.5, 275/022.5, 25/7024.5, 25/7522.5, 25/7022.5, 25/ TA , 2.5, 020, 35/ TA , 275/024.5, 25/7524.5, 25/7524.5, 305/022.5 TA4.0022, 4.5, , 35/022.5 TA5.0020,.5020, 22.5,.522.5, 25/024.5, 25/022.5, 320/7524 d: pair per box / 4 pair per master carton Chain tighteners SHOULD NOT be used. per pair (Lbs.) Replacement Crossmember TC6 TC6 TC65 TC6 TC623 TC623 TC627 Order unit: Pair Alloy Radial Chain (Super singles & wide base) Chain tighteners ARE recommended and included. Partial listing of tire sizes TA /5022.5, 455/ TA , 425/5522.5, 425/6522.5, 425/7022.5, 445/65.5 d: /2 pair per box / 2 pair per master carton Alloy Radial Chain (Truck duals) Partial listing of tire sizes TA , 22.5, 235/022.5, 245/022.5, 255/7022.5, 255/ per pair (Lbs.) Chain tighteners ARE required and included. per pair (Lbs.) 32.0 Replacement Crossmember TC63 TC637 Order unit: Pair Replacement Crossmember TC754 Cable Chain TA , TC754 TA /7522.5, 275/022.5, 25/7024.5, 25/7522.5, 25/7022.5, 25/ TC75 TA , 2.5, 020, 35/ TC762 TA , 275/024.5, 25/7524.5, 25/ TC766 TA ,.0020, 4.5,.5020, 22.5,.522.5, , 25/024.5 d: /2 pair per box / 2 pair per master carton TC770 Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Catalog weights are approximate Minimum order quantity: Master carton 3

114

115 Section 5 Link Chain Traction Products DIAMONDSTYLE PRODUCTS & 4 Whitestar & Whitestar LT Diamond Blue... 4 HPATTERN PRODUCTS Twin Grip Tractor Chain LADDERSTYLE PRODUCTS Quik Grip Passenger... Quik Grip Light Truck... 3 Quik Grip Alloy... 5 Quik Grip Truck Singles... 6 Quik Grip Truck Duals... 3 Truck Unit Chain... 3 Stud Chain Truck Single Stud Chain Truck Dual Quik Grip Skid Steer Quik Grip Forklift Quik Grip OTR Quik Grip Farm Tractor Quik Grip Garden Tractor Quik Grip Snow Blower Quik Grip ATV... 37

116 TRACTION PRODUCTS For passenger and light truck applications Link Chain Whitestar Alloy is a linkstyle, diamond pattern tire chain that operates in a limited space and offers outstanding traction performance. Whitestar Alloy can be installed without moving (or jacking up) the vehicle Whitestar Alloy meets Class S requirements for passenger car and light truck sizes. Better, allaround traction performance than conventional link chains. Cross chains are constructed of manganese alloy steel and have an attractive yellow zinc finish. More durable than any other link style chain, including the original Whitestar. Whitestar Alloy offers the smoothest ride of any link chain available. Included with each pair of chains: Waterproof, illustrated, stepbystep installation and removal instructions, elbow length gloves and an accessory kit which contains a repair link and wire ties to secure any excess side chain links. There is also one pair of rubber tensioners. Everything is stored in a reusable nylon bag. 6 Minimum order quantity: Master carton Catalog weights are approximate

117 TRACTION PRODUCTS Long wearing, high performance for low clearance passenger cars and light trucks. Whitestar Alloy has the easiest installation and best all around traction performance of any SCC linkstyle traction product made for use on passenger vehicles, including pickups and SUVs. It has also been adapted to keep up with the ever increasing demand for products that can operate in the typically small clearances allowed around the drive tires on todayʼs cars and light trucks. In fact, all Whitestar sizes are able to meet SAE Class S clearance requirements. The cross chain links are made of manganese alloy steel, allowing them to be shorter and lighter than other tire chains. This lighter weight helps reduce flyoff during operation and the shorter links provide more gripping points than conventional chains. The reduced size and weight of the links also helps Whitestar to be more durable than other chains less mass equals less wear on both the chain and the road surface. Chain tighteners ARE required and included. Inside fastener Whitestar Alloy (Passenger) Meets S.A.E. Class S Requirements Link Chain Partial listing of tire sizes WS604 45/655, 55/605, 55/654, 55/0, 55/03, 65/654, 65/703, 75/555, 5/554, 5/553 WS605 65/753, 65/03, 75/703, 5/505, 5/555, 5/604, 5/653, 5/505, 205/504, 25/504 WS , 55/705, 65/704, 65/70360, 75/654, 75/655, 5/605, 5/654, 205/554, 25/554 WS60 75/556, 75/704, 5/655, 5/506, 5/555, 5/605, 5/655, 205/506, 205/605, 25/40 WS6 5/556, 205/507, 205/556, 205/606, 205/655, 25/507, 25/556, 25/605, 225/506, 245/407 WS6 205/705, 25/557, 25/606, 25/705, 225/507, 225/556, 235/507, 245/40, 245/506, 245/507 WS64 25/607, 25/656, 25/657, 25/706, 225/606, 225/607, 225/657, 225/755, 235/50, 235/557 d: pair per bag / 4 pair per master carton per pair (Lbs.) Replacement Cross chain WS553 WS557 WS557 WS56 WS565 WS56 WS56 Order unit: Pair Whitestar Alloy (Light truck) Meets S.A.E. Class S Requirements Partial listing of tire sizes WS /756, LT225/756, 235/657, 235/65, 235/706, 235/755, 245/60, 245/657, 245/706, 255/4520 WS /707, LT245/707, 245/756, LT245/756, 255/70, 265/60, 265/657, 265/706, 265/707, 275/5520 d: pair per bag / 3 pair per master carton per pair (Lbs.) Replacement Cross chain WS75 WS7 Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Refer to vehicle ownerʼs manual for any traction product limitations. 7 Minimum order quantity: Master carton Catalog weights are approximate

118 TRACTION PRODUCTS Highway Service PL Class S Chain (Passenger) Not recommended for snow tires or light truck applications. Chain tighteners (QG20070, or QG20070) are REQUIRED, sold separately. d in a durable, reuseable plastic box. Meets S.A.E. Class S Requirements NOTE: Quik Grip PL Chain is the only Quik Grip Link Chain that meets S.A.E. Class S clearance requirements. Link Chain Partial listing of tire sizes QG4 45/655, 55/605, 55/0, 55/03, 65/505, 65/604, 65/653, 65/654, 65/703, 65/753 QG 65/704, 65/70360, 65/754, 65/03, 75/654, 75/703, 75/753, 5/505, 5/554, 5/653 QG2 555, 55/705, 655, 75/04, 5/555, 5/604, 5/606, 5/704, 5/754, 5/03 QG6 75/556, 75/655, 75/704, 5/605, 5/654, 5/655, 205/554, 205/555, 25/506, 25/554 QG30 5/556, 5/605, 5/606, 5/655, 5/656, 5/704, 5/754, 205/506, 205/605, 25/40 QG34 205/507, 205/556, 205/606, 205/655, 25/507, 25/556, 25/557, 25/606, 225/507, 225/556 QG3 25/55, 25/607, 25/656, 25/705, 225/557, 225/606, 225/607, 225/656, 225/705, 225/755 QG42 5/06, 205/756, 25/657, 25/706, 25/756C, 25/05, 225/55, 225/60, 225/657, 225/706 d: pair per box / 4 pair per master carton per pair (Lbs.) Replacement Cross chain QG544 QG544 QG544 QG54 QG54 QG5420 QG5420 QG5422 Order unit: Pair Highway Service RP VBar (Passenger & Light truck) Chain tighteners (QG20070, or QG20070) are REQUIRED, sold separately. d in a durable, reuseable plastic box. DOES NOT Meet S.A.E. Class S Requirements Partial listing of tire sizes QG40 5/705, LT5/754, LT5/755, 205/606, 205/705, 205/754, 25/605, 25/654 per pair (Lbs.).35 Replacement Cross chain QG520 QG50 25/755, 225/705, 225/755, LT225/756, 235/606, 235/656, 235/656, 235/705, 235/ QG522 QG54 25/606, 25/656, 25/705, 25/706, 225/605, 225/606, 225/655, 225/656 d: pair per box / 3 pair per master carton.70 QG522 Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Refer to vehicle ownerʼs manual for any traction product limitations. Minimum order quantity: Master carton Catalog weights are approximate

119 TRACTION PRODUCTS Highway Service (Light truck) Chain tighteners (QG2007, QG20074, or QG20074) are REQUIRED, sold separately. d in a durable, reuseable plastic box. DOES NOT Meet S.A.E. Class S Requirements QG220 QG22 QG224 QG226 QG22 QG222 QG2226* QG222 QG222 Partial listing of tire sizes 74.5LT, 7.004LT, LT5/754, 5/756, 5/756C 7.005LT, , 722.5, 7.507,.5, 225/ LT,.506.5LT, 205/756, 205/756C, 205/06, 225/705 25/755, 25/756, LT25/56, 225/707, 225/755, LT225/ /756, 235/757, LT235/56, 245/706, LT245/707, LT245/756 37x.507, 25/757.5, 305/707, 305/70, LT35/707, 35/ /70, 265/60, LT265/707, 265/70, 265/755, LT265/ /60, 225/657, LT225/756, 235/706, 235/755, 245/657 d: pair per box / 3 pair per master carton (*d one pair per bag.) / pair (Lbs.) CC QG62 QG62 QG622 QG622 QG622 QG622 QG622 QG6225 QG6225 CROSS CHAIN Dia. No. of links 4 CC Hook # QG2005 QG2005 QG2005 QG2005 QG2005 QG2005 QG2005 QG2005 QG2005 SC QG30040 QG30040 QG30040 QG30040 QG30040 QG30040 QG30040 QG30040 QG30040 SIDE CHAIN Dia Fastener QG20063 QG20063 QG20063 QG20063 QG20063 QG20063 QG20063 QG20063 QG20063 Order unit: Pair Highway Service CAM (Light truck) CAM tool # QG200 is supplied in each bag. Chain tighteners are NOT REQUIRED. CAM Link Chain DOES NOT Meet S.A.E. Class S Requirements QG224CAM QG226CAM QG22CAM QG222CAM QG222CAM QG222CAM d: pair per bag Partial listing of tire sizes 7.00, 722.5, 7.507,.5, 225/ LT,.506.5LT, 205/756, 205/756C, 205/06, 225/705 25/755, 25/756, LT25/56, 225/707, 225/755, LT225/ /756, 235/757, LT235/56, 245/706, LT245/707, LT245/ /70, 265/60, LT265/707, 265/70, 265/755, LT265/ /60, 225/657, LT225/756, 235/706, 235/755, 245/657 / pair (Lbs.) CC QG622 QG622 QG622 QG622 QG6225 QG6225 CROSS CHAIN Dia. No. of links CC Hook # QG2005 QG2005 QG2005 QG2005 QG2005 QG2005 SIDE CHAIN SC Dia. Fastener QG QG2000 QG QG2000 QG QG2000 QG QG2000 QG QG2000 QG QG2000 Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Refer to vehicle ownerʼs manual for any traction product limitations. Minimum order quantity: Master carton / bag Catalog weights are approximate

120 TRACTION PRODUCTS Mud Service Single (Light truck) On & off road use. Heavy duty ( ) side chain and ( ) cross chain. Chain tighteners (QG2007, QG20074 or QG20074) are REQUIRED, sold separately. DOES NOT Meet S.A.E. Class S Requirements Partial listing of tire sizes QG x.505LT, 235/65, 235/707, 235/755, 235/756, 245/657 / pair (Lbs.) CC QG6256 CROSS CHAIN Dia. No. of links CC Hook # SIDE CHAIN SC Dia. Fastener QG30060 QG20065 QG /757, LT235/56, LT245/756, 255/657, 255/707 d: pair per bag 3.50 QG6256 QG30060 QG20065 Order unit: Pair Highway Service VBar (Light truck) Chain tighteners (QG2007, QG20074 or QG20074) are REQUIRED, sold separately. DOES NOT Meet S.A.E. Class S Requirements QG20 Partial listing of tire sizes 74.5LT, 7.004LT, LT5/754, 5/756, 5/756C / pair (Lbs.) CC QG6 CROSS CHAIN Dia. No. of links CC Hook # QG2005 SIDE CHAIN SC Dia. Fastener QG QG20063 QG LT, QG6 QG2005 QG QG20063 Link Chain QG24 QG26 QG2 QG , 722.5, , 225/ LT,.506.5LT, 205/756, 205/756C, 205/06, 225/705 25/755, 25/756, LT25/56, 225/707,,225/755, LT225/ /756, 235/757, LT235/56, 245/706, LT245/707, LT245/ QG62 QG62 QG62 QG62 QG2005 QG2005 QG2005 QG2005 QG30040 QG30040 QG30040 QG QG20063 QG20063 QG20063 QG20063 QG22 255/70, 265/60, LT265/707, 265/70, 265/755, LT265/ QG625 QG2005 QG QG20063 QG22 d: pair per bag 225/60, 225/657, LT225/756, 235/706, 235/755, 245/ QG625 QG2005 QG QG20063 Order unit: Pair Highway Service VBar CTO (Light truck) For cold temperature and offroad applications. Special heat treatment to prevent brittleness in extreme cold conditions. Chain tighteners (QG2007, QG20074 or QG20074) are REQUIRED, sold separately. Side chain: / Cross chain: DOES NOT Meet S.A.E. Class S Requirements Partial listing of tire sizes QGV35 235/65, 235/706, 235/755, 245/657, 245/707, LT245/756 QGV320 25/75.5, 225/70.5, 225/75.5, 235/07, LT235/56, LT245/757 d: pair per bag / pair (Lbs.) CC QGV535 QGV535 CROSS CHAIN Dia. No. of links CC Hook # SIDE CHAIN SC Dia. Fastener QG30070 QG20065 QG30070 QG20065 Order unit: Pair This is only partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Refer to vehicle ownerʼs manual for any traction product limitations. 0 Minimum order quantity: Pair Catalog weights are approximate

121 TRACTION PRODUCTS Highway Service Wide Base (Light truck) Maximum recommended speed is 20mph. For 4wheel drive and sport utility vehicles (singles) Chain tighteners (QG2007, QG20074 or QG20074) are REQUIRED, sold separately. DOES NOT Meet S.A.E. Class S Requirements QG32 QG3227 QG322 QG3235 QG3237 d: pair per bag Partial listing of tire sizes 30x.505LT, 245/657, 255/656, 255/706, 265/557, 265/706 3x.505LT, LT265/756, 275/60, LT275/65, 275/706, LT275/70 265/75, 25/707, LT25/756, LT25/756, 305/60, 305/706 36x45LT, 36x5.505LT, 37x.506.5LT, 37x.507, 3x LT 3x5.505, 3x5.505LT / pair (Lbs.) CC QG6225 QG6253 QG625 QG625 QG6265 CROSS CHAIN Dia. No. of links 6 CC Hook # QG2005 QG20053 QG20053 QG20053 QG20053 SIDE CHAIN SC Dia. Fastener QG QG20063 QG30060 QG20065 QG30060 QG20065 QG30060 QG20065 QG30060 QG20065 Order unit: Pair Highway Service Wide Base CAM (Light truck) Maximum recommended speed is 20mph. For 4wheel drive and sport utility vehicles (singles) CAM tool QG200 is supplied in each bag. Chain tighteners are NOT REQUIRED. DOES NOT Meet S.A.E. Class S Requirements Partial listing of tire sizes / pair (Lbs.) CC CROSS CHAIN Dia. CAM No. of links CC Hook # SC SIDE CHAIN Dia. Fastener Link Chain QG32CAM 30x.505LT, 245/657, 255/656, 255/706, 265/557, 265/ QG6225 QG2005 QG QG2000 QG3227CAM 3x.505LT, LT265/756, 275/60, LT275/65, 275/706, LT275/ QG6253 QG20053 QG30060 QG2006 QG322CAM 265/75, 25/707, LT25/756, LT25/756, 305/60, 305/ QG625 QG20053 QG30060 QG2006 d: pair per bag Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Refer to vehicle ownerʼs manual for any traction product limitations. Catalog weights are approximate Minimum order quantity: Pair

122 TRACTION PRODUCTS Mud Service Wide Base (Light truck) Maximum recommended speed is 20mph. For 4wheel drive and sport utility vehicles (singles) Chain tighteners (QG2007, QG20074 or QG20074) are REQUIRED, sold separately. DOES NOT Meet S.A.E. Class S Requirements QG34 QG3427 QG342 Partial listing of tire sizes 7.506LT, 245/707.5, LT245/756, 255/706, 265/705, LT265/ /756, LT265/756, 265/757, LT265/757, LT275/706, 275/756 LT275/707, 25/707, LT25/707, LT25/756, 305/706, LT35/705 QG x.505LT, 37x.507, 37x.5020LT, 305/70, 305/56 d: pair per bag / pair (Lbs.) CC QG625 QG6426 QG6435 QG6436 CROSS CHAIN Dia. No. of links CC Hook # QG20053 SIDE CHAIN SC Dia. Fastener QG30060 QG2006 QG30070 QG2006 QG30070 QG2006 QG30070 QG2006 Order unit: Pair Highway Service Wide Base VBar (Light truck) Maximum recommended speed is 20mph. For 4wheel drive and sport utility vehicles (singles) Chain tighteners (QG2007, QG20074 or QG20074) are REQUIRED, sold separately. Link Chain DOES NOT Meet S.A.E. Class S Requirements QG3 Partial listing of tire sizes 30x.505LT, 245/657, 255/656, 255/706, 265/557, 265/706 / pair (Lbs.) 3.00 CC QG625 CROSS CHAIN Dia. No. of links CC Hook # QG2005 SC QG30040 SIDE CHAIN Dia. 0.2 Fastener QG20063 QG327 3x.505LT, LT265/756, 275/60, LT275/65, 275/706, LT275/ QG653 QG20053 QG30060 QG20065 QG32 265/75, 25/707, LT25/756, LT25/756, 305/60, 305/706 d: pair per bag QG65 QG20053 QG30060 QG20065 Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Refer to vehicle ownerʼs manual for any traction product limitations. 2 Minimum order quantity: Pair Catalog weights are approximate

123 TRACTION PRODUCTS Highway Service DT (Light truck dual/triple) Chain tighteners (QG2007, QG20074 or QG20074) are REQUIRED, sold separately. DOES NOT Meet S.A.E. Class S Requirements QG42 QG422 d: pair per bag Partial listing of tire sizes 25/755, 25/756, LT25/56, 225/707, 225/755, LT225/ /756, 235/757, LT235/56, 245/706, LT245/707, LT245/756 / pair (Lbs.) CC QG622 QG622 CROSS CHAIN Dia. No. of links CC Hook # QG2005 QG2005 SIDE CHAIN SC Dia. Fastener QG QG20063 QG QG20063 Order unit: Pair Highway Service DTCAM (Light truck dual/triple) CAM tool # QG200 is supplied in each bag. Chain tighteners are NOT REQUIRED. CAM DOES NOT Meet S.A.E. Class S Requirements QG42CAM QG422CAM QG422CAM QG422CAM Partial listing of tire sizes 25/755, 25/756, LT25/56, 225/707, 225/755, LT225/ /756, 235/757, LT235/56, 245/706, LT245/707, LT245/ /70, 265/60, LT265/707, 265/70, 265/755, LT265/ /60, 225/657, LT225/756, 235/706, 235/755, 245/657 / pair (Lbs.) CC QG622 QG622 QG6225 QG6225 CROSS CHAIN Dia. No. of links CC Hook # QG2005 QG2005 QG2005 QG2005 SIDE CHAIN SC Dia. Fastener QG QG2000 QG QG2000 QG QG2000 QG QG2000 Link Chain d: pair per bag Order unit: Pair Highway Service DT VBar (Light truck dual/triple) Chain tighteners (QG2007, QG20074 or QG20074) are REQUIRED, sold separately. DOES NOT Meet S.A.E. Class S Requirements QG4 QG42 QG42 QG42 d: pair per bag Partial listing of tire sizes 25/755, 25/756, LT25/56, 225/707, 225/755, LT225/ /756, 235/757, LT235/56, 245/706, LT245/707, LT245/ /70, 265/60, LT265/707, 265/70, 265/755, LT265/ /60, 225/657, LT225/756, 235/706, 235/755, 245/657 / pair (Lbs.) CC QG62 QG62 QG625 QG625 CROSS CHAIN Dia. No. of links CC Hook # QG2005 QG2005 QG2005 QG2005 SC QG30040 QG30040 QG30040 QG30040 SIDE CHAIN Dia Fastener QG20063 QG20063 QG20063 QG20063 Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Refer to vehicle ownerʼs manual for any traction product limitations. Catalog weights are approximate Minimum order quantity: Pair 3

124 TRACTION PRODUCTS Premium Alloy Truck Chain Diamond Blue cross chains are made from high grade manganese alloy steel. Alloy tire chains wear considerably longer than regular carbon steel chains. This makes them ideal for trucks that use their chains often and/or for extended periods of time. Diamond Blue chains weigh an average of 25% less than equivalent standard highway chains making them easier to install. The "D" shaped or "square rod" links have more gripping power than round rod chains. Combine that with the diamond pattern design of the cross chains, and they become some of the longest lasting, best gripping, easiest to use chains on the market. 5.5mm D shaped alloy cross chain links. Diamond pattern cross chains provide better lateral traction than ladder style chain. Bell shaped cross chain end hooks. CAM tool #QG2005 is included in each bag of chain. Chain tighteners are not required. Link Chain Silver zinc finish with blue powdercoat side chain. Square rod links Cam tightening system Cross chain end hooks Diamond Pattern Highway Service Alloy CAM Style (Truck singles) DB , 22.5 Partial listing of tire sizes / pair (Lbs.) 3.60 CC DB605 CROSS CHAIN Dia. No. of (mm) links 5.5 x *CC Hook # DB53 SC DB30050 SIDE CHAIN Dia. (mm) 5.0 *Fastener DB6 DB /7522.5, 275/022.5, 25/7522.5, 25/7022.5, 25/ DB x DB53 DB DB6 DB , 2.5, 25/7024.5, 305/7022.5, 35/7022.5, 35/ DB x DB53 DB DB6 DB /024.5, 25/ DB x DB53 DB DB6 DB , DB x DB53 DB DB6 DB ,.520, 22.5, 25/024.5, 25/022.5, 305/022.5 d: pair per bag DB x DB53 DB DB6 Order unit: Pair * NOTE: These parts are available through special order only. This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Minimum order quantity: Pair Catalog weights are approximate

125 TRACTION PRODUCTS HD Alloy Square Rod Truck Chain Quik Grip HD Alloy cross chains are made from high grade manganese alloy steel. Alloy tire chains wear considerably longer than regular carbon steel chains. This makes them ideal for trucks that use their chains often and/or for extended periods of time. The "square rod" links have more gripping power than round rod chains. The heavy duty cross chains will out perform any traditional ladder link chain on the market, lasting longer and providing much more aggressive traction. Short pitch (length), 7mm square rod cross chain links. Bell shaped cross chain end hooks. Chain tighteners are not required. CAM tool #QG2005 is included in each bag of chain. Yellow zinc finish. Square rod links QG243 Square Rod Alloy Highway Service CAM Style (Truck singles) Partial listing of tire sizes 275/7522.5, 275/022.5, 25/7522.5, 25/7022.5, 25/ / pair (Lbs.) 6.20 CC QG655 CROSS CHAIN Dia. (mm) 7 x 7 No. of links 5 CC Hook # QG2054 SC QG3060 SIDE CHAIN Dia. Fastener QG206 Link Chain QG , 2.5, 25/7024.5, 305/7022.5, 35/7022.5, 35/ QG653 7 x 7 3 QG2054 QG3060 QG206 QG /024.5, 25/7524.5, 305/ QG655 7 x 7 5 QG2054 QG3060 QG206 QG24 d: pair per bag.0022, QG653 7 x 7 3 QG2054 QG3060 QG206 Order unit: Pair Square Rod Alloy Highway Service DT CAM Style (Truck dual/triple) QG443 Partial listing of tire sizes 275/7522.5, 275/022.5, 25/7522.5, 25/7022.5, 25/ / pair (Lbs.).70 CC QG655 CROSS CHAIN Dia. (mm) 7 x 7 No. of links 5 CC Hook # QG2054 SC QG3060 SIDE CHAIN Dia. Fastener QG206 QG , 2.5, 25/7024.5, 305/7022.5, 35/7022.5, 35/ QG653 7 x 7 3 QG2054 QG3060 QG206 QG /024.5, 25/7524.5, 305/ QG655 7 x 7 5 QG2054 QG3060 QG206 QG , 4.5 d: /2 pair per bag 6.0 QG653 7 x 7 3 QG2054 QG3060 QG206 Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Catalog weights are approximate Minimum order quantity: Pair 5

126 TRACTION PRODUCTS Highway Service (Truck singles) Chain tighteners (QG2006 or QG20073) are RECOMMENDED, sold separately. QG2235 Partial listing of tire sizes.522.5, 25/ / pair (Lbs.) 62.0 CC QG6255 CROSS CHAIN Dia. No. of links CC Hook # QG20053 SIDE CHAIN SC Dia. Fastener QG30060 QG20065 QG , 22.5, 245/7022.5, 265/6520, 265/70.5, 265/ QG625 QG20053 QG30060 QG20065 QG , 235/022.5, 245/7522.5, 245/022.5, 255/7022.5, 255/ QG625 QG20053 QG30060 QG20065 QG , QG625 QG20053 QG30060 QG20065 QG /7522.5, 275/022.5, 25/7522.5, 25/7022.5, 25/ QG6253 QG20053 QG30060 QG20065 QG , 2.5, 25/ QG625 QG20053 QG30060 QG20065 QG /024.5, 25/ QG6255 QG20053 QG30060 QG20065 QG , QG6253 QG20053 QG30060 QG20065 QG , 22.5, 25/024.5, 25/022.5, 305/022.5, 320/ QG6260 QG30070 QG20065 QG ,.0020, 24.5, 305/7524.5, 305/522.5, 35/ QG6263 QG30070 QG20065 QG QG6263 QG30070 QG20065 d: pair per bag Order unit: Pair Link Chain Highway Service CAM (Truck singles) CAM tool #QG2005 is supplied in each bag. CAM Chain tighteners are NOT required. QG2234CAM 25/70.5 Partial listing of tire sizes / pair (Lbs.) CC QG6253 CROSS CHAIN Dia. No. of links CC Hook # QG20053 SIDE CHAIN SC Dia. Fastener QG30060 QG2006 QG223CAM , 235/022.5, 245/7522.5, 245/022.5, 255/7022.5, 255/ QG625 QG20053 QG30060 QG2006 QG224CAM.0020, QG625 QG20053 QG30060 QG2006 QG2243CAM 275/7522.5, 275/022.5, 25/7522.5, 25/7022.5, 25/ QG6253 QG20053 QG30060 QG2006 QG2245CAM.0020, 2.5, 25/ QG625 QG20053 QG30060 QG2006 QG2247CAM 275/024.5, 25/ QG6255 QG20053 QG30060 QG2006 QG224CAM.0022, QG6253 QG20053 QG30060 QG2006 QG225CAM.0020, 22.5, 25/024.5, 25/022.5, 305/022.5, 320/ QG6260 QG30070 QG2006 QG2255CAM.0022,.0020, 24.5, 305/7524.5, 305/522.5, 35/ QG6263 QG30070 QG2006 d: pair per bag Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Minimum order quantity: Pair Catalog weights are approximate

127 TRACTION PRODUCTS Heavy duty cross chains. Chain tighteners are NOT required. CAM tool #QG2005 is supplied in each bag. Heavy Duty Highway Service CAM/HD (Truck singles) Partial listing of tire sizes QG2236HD 275/024.5, 25/ QG2244HD.0020, 2.5, 275/7522.5, 275/022.5, 25/7024.5, 25/ QG2250HD.0022, 4.5 d: pair per bag / pair (Lbs.) CC QG6263 QG6260 QG6260 CROSS CHAIN Dia. No. of links CAM CC Hook # SIDE CHAIN SC Dia. Fastener QG30065 QG2006 QG30065 QG2006 QG30065 QG2006 Order unit: Pair Highway Service VBar (Truck singles) Chain tighteners (QG2006 or QG20073) are RECOMMENDED sold separately. QG237 Partial listing of tire sizes , 22.5, 245/7022.5, 265/6520, 265/70.5, 265/75.5 / pair (Lbs.) 44.0 CC QG622 CROSS CHAIN Dia. No. of links CC Hook # QG20053 SIDE CHAIN SC Dia. Fastener QG30060 QG20065 QG , 235/022.5, 245/7522.5, 245/022.5, 255/7022.5, 255/ QG622 QG20053 QG30060 QG20065 QG , QG622 QG20053 QG30060 QG20065 QG , 2.5, 25/ QG622 QG20053 QG30060 QG20065 QG , QG653 QG20053 QG30060 QG20065 QG , 22.5, 25/024.5, 25/022.5, 305/022.5, 320/7524 QG QG ,.0020, 24.5, 305/7524.5, 305/522.5, 35/022.5 QG d: pair per bag QG660 QG660 QG663 QG663 QG30070 QG30070 QG30070 QG30070 QG20065 QG20065 QG20065 QG20065 Order unit: Pair Link Chain CAM tool #QG2005 is supplied in each bag. Chain tighteners are NOT required. Highway Service VBar CAM (Truck singles) Partial Listing of tire sizes QG23CAM , 235/022.5, 245/7522.5, 245/022.5, 255/7022.5, 255/022.5 QG24CAM.0020, 22.5 QG243CAM 275/7522.5, 275/022.5, 25/7522.5, 25/7022.5, 25/ QG245CAM.0020, 2.5, 25/ QG247CAM 275/024.5, 25/ QG24CAM.0022, 4.5 QG25CAM.0020, 22.5, 25/024.5, 25/022.5, 305/022.5, 320/7524 QG255CAM.0022,.0020, 24.5, 305/7524.5, 305/522.5, 35/022.5 d: pair per bag / pair (Lbs.) CC QG622 QG622 QG653 QG622 QG626 QG653 QG660 QG663 This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Catalog weights are approximate Minimum order quantity: Pair CAM CROSS CHAIN Dia. No. of links CC Hook # QG20053 QG20053 QG20053 QG20053 QG20053 QG20053 SIDE CHAIN SC Dia. Fastener QG30060 QG2006 QG30060 QG2006 QG30060 QG2006 QG30060 QG2006 QG30060 QG2006 QG30060 QG2006 QG30070 QG2006 QG30070 QG2006 Order unit: Pair

128 TRACTION PRODUCTS Highway Service VBar CAM & NonCAM CTO (Truck singles) CAM tool #QG2005 is supplied in each bag of QGVC CAM chain. Chain tighteners (#QG2006 or QG20073) are RECOMMENDED for NONCAM product, sold separately. Special heat treatment for extreme cold temperatures. Heavy duty ( ) cross chain and side chain. QGV343HD QGV344HD QGV355 QGV356 QGVC343HD QGVC344HD d: pair per bag Partial listing of tire sizes.0020, 2.5, 275/022.5, 25/7522.5, 25/7022.5, 35/ , 4.5,.522.5, 275/024.5, 25/7524.5, 25/ ,.5020, 22.5,.522.5, 305/ ,.0020, , 2.5, 275/022.5, 25/7522.5, 25/7022.5, 35/ , 4.5,.522.5, 275/024.5, 25/7524.5, 25/ / pair (Lbs.) CC QGV5340HD QGV5340HD QGV5355 QGV5355 QGV5340HD QGV5340HD CROSS CHAIN Dia. CAM No. of links CC Hook # SC QG30070 QG30070 QG30070 QG30070 QG30070 QG30070 SIDE CHAIN Dia. Fastener QG20062 QG20062 QG20062 QG20062 QG2007 QG2007 Order unit: Pair Single Mud Service SM (Truck singles) On and off road use. Heavy Duty side chain and cross chain. Chain tighteners (#QG2006 or QG20073) are RECOMMENDED, sold separately. Link Chain Partial listing of tire sizes QG , 2.5 QG ,.0020, 4.5,.5020, 22.5, 305/522.5 d: pair per bag / pair (Lbs.) CC QG6435 QG6435 CROSS CHAIN Dia. No. of links CC Hook # SIDE CHAIN SC Dia. Fastener QG30070 QG20065 QG30070 QG20065 Order unit: Pair Highway Service Wide Base CAM & NonCAM (Super singles) Maximum recommended speed is 20mph. CAM tool #QG2005 is supplied in each bag of CAM chain. Chain tighteners (#QG2006 or QG20073) are RECOMMENDED for NONCAM product, sold separately. QG3255 Partial listing of tire sizes 522.5, 6.5.5, 365/520, 35/ / pair (Lbs.) 6.00 CC QG723 CAM CROSS CHAIN Dia. No. of links 3 CC Hook # SIDE CHAIN SC Dia. Fastener QG30060 QG20065 QG ,.5.5, 35/520, 445/ QG724 4 QG30060 QG20065 QG / QG725 5 QG30060 QG20065 QG / QG QG30060 QG20065 QG326CAM 445/5022.5, 445/ QG725 5 QG30060 QG2006 QG327CAM d: pair per bag , 425/5522.5, 425/6522.5, 425/7022.5, 445/ QG725 5 QG30060 QG2006 Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Minimum order quantity: Pair Catalog weights are approximate

129 TRACTION PRODUCTS Highway Service DT (Truck dual/triple) Chain tighteners (QG2006 or QG20073) are RECOMMENDED, sold separately. QG4235 QG4237 QG423 QG424 QG4243 QG4245 QG4247 QG424 QG425 QG4255 d: /2 pair per bag Partial listing of tire sizes.522.5, 25/ , 22.5, 245/7022.5, 255/7520, 265/6520, 265/ ,.2520, 235/022.5, 245/7522.5, 245/022.5, 255/ , /7522.5, 275/022.5, 25/7522.5, 25/7022.5, 25/ ,.00/020, 2.5, 25/ /024.5, 25/ , ,.5020, 22.5, 25/024.5, 25/022.5, 305/ ,.0020, 24.5,.524.5, 305/7524.5, 305/522.5 / pair (Lbs.) CC QG6255 QG625 QG625 QG625 QG6253 QG625 QG6255 QG6253 QG6260 QG6263 CROSS CHAIN Dia. No. of links CC Hook # QG20053 QG20053 QG20053 QG20053 QG20053 QG20053 QG20053 QG20053 SIDE CHAIN SC Dia. Fastener QG30060 QG20065 QG30060 QG20065 QG30060 QG20065 QG30060 QG20065 QG30060 QG20065 QG30060 QG20065 QG30060 QG20065 QG30060 QG20065 QG30070 QG20065 QG30070 QG20065 Order unit: Pair Highway Service DT CAM (Truck dual/triple) CAM tool #QG2005 is supplied in each bag. CAM Chain tighteners are NOT required. QG423CAM Partial listing of tire sizes ,.2520, 235/022.5, 245/7522.5, 245/022.5, 255/ / pair (Lbs.) 2.00 CC QG625 CROSS CHAIN Dia. No. of links CC Hook # QG20053 SIDE CHAIN SC Dia. Fastener QG30060 QG2006 Link Chain QG424CAM.0020, QG625 QG20053 QG30060 QG2006 QG4243CAM 275/7522.5, 275/022.5, 25/7522.5, 25/7022.5, 25/ QG6253 QG20053 QG30060 QG2006 QG4245CAM.0020,.00/020, 2.5, 25/ QG625 QG20053 QG30060 QG2006 QG4247CAM 275/024.5, 25/ QG6255 QG20053 QG30060 QG2006 QG424CAM.0022, 4.5 d: /2 pair per bag 0.00 QG6253 QG20053 QG30060 QG2006 Order unit: Pair Heavy Duty Highway Service DT CAM / HD (Truck dual/triple) Heavy duty cross chains. Chain tighteners are NOT required. CAM CAM tool #QG2005 is supplied in each bag. QG4236HD Partial listing of tire sizes 275/024.5, 25/ / pair (Lbs.) 4.50 CC QG6263 CROSS CHAIN Dia. No. of links CC Hook # SIDE CHAIN SC Dia. Fastener QG30065 QG2006 QG4244HD.0020, 2.5, 275/7522.5, 275/022.5, 25/7024.5, 25/ QG6260 QG30065 QG2006 QG4250HD.0022, 4.5 d: /2 pair per bag 7.00 QG6260 QG30065 QG2006 Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Catalog weights are approximate Minimum order quantity: Pair

130 TRACTION PRODUCTS Mud Service DTM (Truck dual/triple) On and off road use. Heavy Duty side chain and cross chain. Chain tighteners (#QG2006 or QG20073) are RECOMMENDED, sold separately. QG , 2.5 Partial listing of tire sizes / pair (Lbs.) CC QG6435 CROSS CHAIN Dia. No. of links CC Hook # SIDE CHAIN SC Dia. Fastener QG30070 QG20065 QG ,.0020, 4.5,.5020, 22.5 d: /2 pair per bag 5.00 QG6435 QG30070 QG20065 Order unit: Pair Highway Service RDT VBAR (Truck dual/triple) Chain tighteners (QG2006 or QG20073) are RECOMMENDED, sold separately. QG437 Partial listing of tire sizes , 22.5, 245/7022.5, 255/7520, 265/6520, 265/70.5 / pair (Lbs.) 2.00 CC QG622 CROSS CHAIN Dia. No. of links CC Hook # QG20053 SIDE CHAIN SC Dia. Fastener QG30060 QG20065 QG ,.2520, 235/022.5, 245/7522.5, 245/022.5, 255/ QG622 QG20053 QG30060 QG20065 QG , QG622 QG20053 QG30060 QG20065 Link Chain QG445 QG44 QG45 QG455 d: /2 pair per bag.0020,.00/020, 2.5, 25/ , ,.5020, 22.5, 25/024.5, 25/022.5, 305/ ,.0020, 24.5,.524.5, 305/7524.5, 305/ QG622 QG653 QG660 QG663 QG20053 QG20053 QG30060 QG30060 QG30070 QG30070 QG20065 QG20065 QG20065 QG20065 Order unit: Pair Highway Service RDT VBar CAM (Truck dual/triple) CAM tool #QG2005 is supplied in each bag. Chain tighteners are NOT required. CAM QG443CAM Partial listing of tire sizes 275/7522.5, 275/022.5, 25/7522.5, 25/7022.5, 25/ / pair (Lbs.) 7.50 CC QG653 CROSS CHAIN Dia. No. of links CC Hook # QG20053 SIDE CHAIN SC Dia. Fastener QG30060 QG2006 QG445CAM.0020,.00/020, 2.5, 25/ QG622 QG20053 QG30060 QG2006 QG447CAM 275/024.5, 25/ QG626 QG20053 QG30060 QG2006 QG44CAM.0022, 4.5 d: /2 pair per bag.00 QG653 QG20053 QG30060 QG2006 Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Minimum order quantity: Pair Catalog weights are approximate

131 TRACTION PRODUCTS Highway Service RDT VBar CAM & NonCAM CTO (Truck dual/triple) CAM tool #QG2005 is supplied in each bag of QGVC CAM chain. Chain tighteners (#QG2006 or QG20073) are RECOMMENDED for NONCAM product, sold separately. Special heat treatment for extreme cold temperatures. Heavy duty () cross chain and side chain. QGV743HD QGV744HD QGV755 QGV756 QGVC743HD QGVC744HD d: /2 pair per bag Partial listing of tire sizes.0020, 2.5, 275/7522.5, 275/022.5, 25/7522.5, 25/ , 4.5,.522.5, 275/024.5, 25/7524.5, 25/ ,.5020, 22.5,.522.5, 305/ ,.0020, , 2.5, 275/7522.5, 275/022.5, 25/7522.5, 25/ , 4.5,.522.5, 275/024.5, 25/7524.5, 25/ / pair (Lbs.) CC 6.00 QGV5340HD QGV5340HD QGV QGV QGV5340HD QGV5340HD CAM CROSS CHAIN Dia. No. of links CC Hook # SIDE CHAIN SC Dia. Fastener QG30070 QG20062 QG30070 QG20062 QG30070 QG20062 QG30070 QG20062 QG30070 QG2007 QG30070 QG2007 Order unit: Pair Truck Unit Chain (Truck singles) Do not use for continuous driving Truck Unit Chains are made for fast, simple installation. For all truck tires with spoke wheels or wheels with minimum diameter hand holes. Constructed of case hardened twist link cross chain and straight side links ( diameter) for easy installation. Snap links, which are sold separately, are required for hookup of each individual chain. QG20 QG202 Trade size 77 Dia. Partial listing of tire sizes (.255LT, 6LT, 20) (.006LT, 20) (5LT, 6.5LT, 7.5), 5LT, TR,.0020,.0022, Total length per bag (Lbs) Link Chain QG , 4.5,.0020, 2, 4, d: 5 per bag NOTE: When unit chain is referred to as it means that there are twist links with straight links attached to each side. Furnished without snap links. Other sizes available by special order. Snap Link for Truck Unit Chain Install as shown in the illustration to the right to prevent putting excess tension on the snap link. Trade size d: pieces per bag Dia. Use with: per bag (Lbs) H /6 For all truck unit chains shown above.60 Packaging / bag NOTE: Check local regulations for minimum cross chain requirements. Unit chains are legal in all states and provinces. However, in some states emergency chains do not meet the minimum requirements for highway use when authorities post an order to use chains. WARNING: UNIT CHAINS ARE MEANT FOR VERY SHORT TERM DRIVING ONLY. For distance travel through ice and snow conditions, SCC recommends traction products that provide crossmembers evenly spaced around the circumference of the tire, such as those shown elsewhere in this catalog. ALWAYS CHECK DISC BRAKE CLEARANCE BEFORE USING UNIT CHAINS This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Catalog weights are approximate Minimum order quantity: Pair or factory package 3

132 TRACTION PRODUCTS Studded truck chain is constructed from highgrade manganese alloy steel for use in offroad applications requiring extra aggressive traction such as mining, logging, farming, or construction. Single CAM style has 3 twin CAMS on the outside of each half set and a CAM style fastener. Dual/triples have CAMʼs on the inside as well as the outside side chain. The twin CAM performs better than a standard CAM as it is much less likely to be pushed open in deep mud or rough terrain applications. Stud dimensions:.7mm (.343 ) diameter, 5mm (.50 ) height. Yellow Zinc finish. NOTE: NOT RECOMMENDED for on road or highway use. mm Stud Chain CAM & NonCAM (Off Road Truck singles) CAM tool #QG2005 is supplied in each bag of HDC CAM chain. Chain tighteners (#QG2006 or QG20073) are REQUIRED for NONCAM product only, sold separately. CAM QGS343HD Partial listing of tire sizes.0020, 2.5, 275/022.5, 25/7522.5, 25/7022.5, 35/ / pair (Lbs.) 7.70 CC QGS340HD CROSS CHAIN Dia. (mm) No. of links *CC Hook # QG20254 *SC QG30270 SIDE CHAIN Dia. Fastener (mm) 7.2 QG20062XL QGS344HD.0022, 4.5,.522.5, 275/024.5, 25/7524.5, 25/ QGS340HD QG20254 QG QG20062XL QGS355HD.0020,.5020, 22.5,.522.5, 305/ QGS355HD QG20254 QG QG20062XL QGS356HD.0022,.0020, QGS355HD QG20254 QG QG20062XL QGS343HDC.0020, 2.5, 275/022.5, 25/7522.5, 25/7022.5, 35/ QGS340HD QG20254 QG QG20062XL QGS344HDC.0022, 4.5,.522.5, 275/024.5, 25/7524.5, 25/ QGS340HD QG20254 QG QG20062XL QGS355HDC.0020,.5020, 22.5,.522.5, 305/ QGS355HD QG20254 QG QG20062XL QGS356HDC.0022,.0020, QGS355HD QG20254 QG QG20062XL Link Chain d: pair per bag * NOTE: These parts are available through special order only. mm Stud Chain CAM & NonCAM (Off Road Truck dual/triple) Order unit: Pair CAM tool #QG2005 is supplied in each bag of HDC CAM chain. Chain tighteners (#QG2006 or QG20073) are REQUIRED for NONCAM product only, sold separately. CAM QGS743HD Partial listing of tire sizes.0020, 2.5, 275/7522.5, 275/022.5, 25/7522.5, 25/ / pair (Lbs.) CC QGS340HD CROSS CHAIN Dia. (mm) No. of links *CC Hook # QG20254 *SC QG30270 SIDE CHAIN Dia. (mm) 7.2 Fastener QG20062XL QGS744HD.0022, 4.5,.522.5, 275/024.5, 25/7524.5, 25/ QGS340HD QG20254 QG QG20062XL QGS755HD.0020,.5020, 22.5,.522.5, 305/ QGS355HD QG20254 QG QG20062XL QGS756HD.0022,.0020, QGS355HD QG20254 QG QG20062XL QGS743HDC.0020, 2.5, 275/7522.5, 275/022.5, 25/7522.5, 25/ QGS340HD QG20254 QG QG20062XL QGS744HDC.0022, 4.5,.522.5, 275/024.5, 25/7524.5, 25/ QGS340HD QG20254 QG QG20062XL QGS755HDC.0020,.5020, 22.5,.522.5, 305/ QGS355HD QG20254 QG QG20062XL QGS756HDC.0022,.0020, QGS355HD QG20254 QG QG20062XL d: /2 pair per bag * NOTE: These parts are available through special order only. Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Minimum order quantity: Pair Catalog weights are approximate

133 TRACTION PRODUCTS Skid Steer & Skid Loader Chain Chain tighteners (QG20070 for QG3503 or QG20074 for QG3505~QG3540) are RECOMMENDED, sold separately. QG3503 Partial listing of tire sizes 23x.50NHS, 23x.50SS / pair (Lbs.) 25. CC QG6253 CROSS CHAIN Dia. No. of links CC Hook # QG20053 SC QG30060 SIDE CHAIN Dia. Fastener QG2006 QG x.54SS 2.35 QG6253 QG20053 QG30060 QG2006 QG NHS 3.75 QG6253 QG20053 QG30060 QG2006 QG NHS, 2x.006NHS, 2x5.505NHS 57. QG6435 QG30070 QG2006 QG NHS, 33x.505NHS QG6436 QG30070 QG2006 QG NHS, 47.5SS, 36x3.55NHS QG643 3 QG30070 QG2006 d: pair per bag Order unit: Pair Forklift Chain (Off road use) 5.5mm Square rod cross chains. Chain tighteners (QG20070) are RECOMMENDED, sold separately. QG03 6x, 6.50 Partial listing of tire sizes / pair (Lbs.) 4.60 CC QG6046 CROSS CHAIN Dia. (mm) 5.5 No. of links CC Hook # SC QG30040 SIDE CHAIN Dia. 0.2 Fastener QG , 23x5, 25x7.55, 25x.504SS 5.00 QG QG QG0 QG07 QG05 QG0 7.00,.55, 2x5, 2x.55, 2x5, 2x , 7.506, 27x.505NHS, 2x5 23x.5 27x QG6046 QG6046 QG604 QG QG30040 QG30040 QG30040 QG Link Chain QG QG QG d: pair per bag Order unit: Pair For Grader, Scrapers and Heavy Equipment Type OTR (Off road use) QG26 Partial listing of tire sizes , , GRADER, 4.002, 5.525, 30/702 / pair (Lbs.).00 CC QG6630R CROSS CHAIN Dia. No. of links 7 CC Hook # QG20055 SC QG30070 SIDE CHAIN Dia. Fastener QG20065 QG , GRADER, QG6630R 7 QG20055 QG30070 QG20065 QG , 6.002, QG QG2005 QG3000 QG20066 QG , QG QG2005 QG3000 QG20066 QG , 540/ QG QG2005 QG3000 QG20066 QG ,.0025,.0026, 520/ QG QG2005 QG3000 QG20066 QG QG QG2005 QG QG20066 QG264 2L24, d: /2 pair per bag QG QG2005 QG QG20066 Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Catalog weights are approximate Minimum order quantity: Pair 33

134 TRACTION PRODUCTS Ladder Style Farm Tractor Type FTH QG022*.324 Partial listing of tire sizes / pair (Lbs.) CC QG6435 CROSS CHAIN Dia. No. of links CC Hook # SIDE CHAIN SC Dia. Fastener QG30070 QG20065 QG , QG6435 QG30070 QG20065 QG034.5/ QG QG20055 QG30070 QG20065 QG036.52, QG QG20055 QG30070 QG20065 QG03.532,.22,.230, QG QG20055 QG30070 QG20065 QG050.46, 3.66, QG QG20055 QG30070 QG20065 QG ,.424, QG QG20055 QG30070 QG20065 QG , QG QG20055 QG30070 QG20065 QG , QG QG20055 QG30070 QG20065 QG ,.53,.542,.23,.436,.43, 320/ QG QG20055 QG30070 QG20065 QG ,.442, 3.636, 3.63, QG QG20055 QG30070 QG20065 QG , 4.2, 30/52, 420/ QG QG20055 QG30070 QG20065 QG , 7.5L QG7426 QG20055 QG30070 QG20065 QG , 6.26, 6.2, 30/530, 420/52, 440/ QG7426 QG20055 QG30070 QG20065 QG , 30/ QG7426 QG20055 QG30070 QG20065 Link Chain QG07 QG00 QG02 QG , 6.34, 30/03, 420/534, 420/ , 2.5L6..424,.426,.5L24, 40/702, 40/ QG7426 QG7426 QG562 QG QG20055 QG20055 QG2005 QG2005 QG30070 QG30070 QG3000 QG3000 QG20065 QG20065 QG20066 QG20066 QG05.430, 2L QG QG2005 QG3000 QG20066 QG QG QG2005 QG3000 QG20066 QG0.43, 40/ QG QG2005 QG3000 QG20066 QG QG QG2005 QG3000 QG20066 QG QG QG2005 QG3000 QG20066 d: /2 pair per bag (* pair per bag) Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Minimum order quantity: Pair Catalog weights are approximate

135 TRACTION PRODUCTS Farm Tractor & Industrial Type Twin Grip (Off road use) Not for highway use Adjacent cross chains interconnected to prevent cross chain from dropping into the grooves of the tire tread. * Note: 2 link back space on last cross chain section of each /2 pair. Partial listing of tire sizes QG33.532,.224 / pair (Lbs.).0 CC QG330 CROSS CHAIN Dia. No. of links CC Hook # SIDE CHAIN SC Dia. Fastener QG30070 QG20065 QG342*.536,.22,.230,.232,.42, 250/ QG330 QG30070 QG20065 QG346*.540,.234,.236, 20/ QG330 QG30070 QG20065 QG34*.542,.23,.240,.436,.43, 320/ QG330 QG30070 QG20065 QG QG350 4 QG30070 QG20065 QG374* 3.62, 4.24, 4.26, 4.2, 30/52, 420/ QG350 4 QG30070 QG20065 QG376* 3.636, 3.36, 4.30, 30/ QG350 4 QG30070 QG20065 QG QG350 4 QG30070 QG20065 QG37* 4.36, 4.3, 320/ QG350 4 QG30070 QG20065 QG37* QG360 6 QG30070 QG20065 QG3 6.2,.5L24, 2.56, 2.5L6., 440/02, 40/ QG360 6 QG30070 QG20065 QG3 6.32, QG360 6 QG30070 QG20065 QG32* 5.53, 6.30,.426, 30/03, 30/534, 420/ QG360 6 QG30070 QG20065 QG34 QG36* QG , 6.3,.430,.434, 420/534.43, 40/ , 23.6, QG360 QG360 QG QG30070 QG30070 QG30070 QG20065 QG20065 QG20065 Link Chain QG3 20.3, 23.34, QG360 6 QG30070 QG20065 d: /2 pair per bag Order unit: Pair IMPORTANT INFORMATION FOR CUTTING DOWN TRACTOR CHAINS: Limit your inventory investment by stocking the longest chain within a grouping. Tractor chain can be cutdown to fit smaller size tires. Bolt cutter (H46200) and chain pliers (QG2003) are required. SCC offers a plasticized fit chart with all FTH and Twin Grip tractor chain applications and cutdown instructions. TRACTOR CHAIN TYPE FTH By stocking the following 6 part numbers, you can sell 27 different part numbers. QG032, QG062, QG066, QG00, QG0, QG03 TRACTOR CHAIN TWIN GRIP By stocking the following 3 part numbers, you can sell 7 different part numbers. QG34, QG37, QG3 This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Catalog weights are approximate Minimum order quantity: Pair 35

136 TRACTION PRODUCTS Garden Tractor & Snow Blower Chain (Off road use) 2 link crossmember spacing. Chain tighteners may be RECOMMENDED (See below). QG0202 / Partial listing of tire sizes / pair (Lbs.) 5.70 Chain Tightener N/A CROSS CHAIN CC Dia. (mm) No. of links 5 Dia SIDE CHAIN No. of links (outside) 2 QG0205.5x3, x3.50,.25x N/A QG020 4./3.505, x N/A QG x3.005, 4.x3.504, x N/A QG02 4.x3.506,.25x N/A QG /4.506, 4x5.006, 4x N/A QG0226 x74,.5x4.506, 3x4., 3x4.005, 3x4.006, 3x N/A QG x N/A QG0233 4x5.505, 5x5.006, 5x N/A Link Chain QG0236 QG0250 QG0253 QG0256 x /5.70, 6x5.50, 6x6.50 x.50 x.50, x.50, x N/A QG20030 QG20030 QG QG025 20x7, 20x.00, 20x.00, 20x QG QG x.00, 20x.00, 20x.00, 2x QG QG0266 x, 22x7.50, 22x.00, 23x QG QG026 23x.50, 24x.004, 24x QG QG027 2x.50, 2x.00, 22x.00, 23x.50, 24x QG QG x.00, 23x.00, 23x.50, 24x QG QG x3.00, 26x.00, 26x.00, 26x QG QG02 2x QG QG020 24x QG d: pair per bag Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Minimum order quantity: Pair Catalog weights are approximate

137 TRACTION PRODUCTS Garden Tractor & Snow Blower Chain 4 link crossmember spacing. Chain tighteners QG20030, QG20032 or QG2004 are RECOMMENDED (See below). QG0450 Partial listing of tire sizes 5.00/5.70, 6x5.50, 6x6.50 / pair (Lbs.) 6.25 Tightener QG20030 CROSS CHAIN CC Dia. (mm) 0.77 No. of links 7 Dia SIDE CHAIN No. of links (outside) 3 QG0453 x QG QG0456 x.50, x.50, x QG QG045 20x7, 20x.00, 20x.00, 20x QG QG x.00, 20x.00, 20x.00, 2x QG QG0466 x, 22x7.50, 22x.00, 23x QG QG047 20x.50, 2x.00, 22x.00, 23x.50, 24x QG QG x.00, 23x.00, 23x.50, 24x QG QG x3.00, 26x.00, 26x.00, 26x QG QG04 2x.005 d: pair per bag 7.00 QG Order unit: Pair ATV Chain (On / off road use) Link Chain 2 Link spacing. Chain tighteners (QG20032 or QG2004) are required. (See page 46) QG0636 QG0640 QG0642 QG0644 QG0646 QG064 QG0660 QG0662 Partial listing of tire sizes 2x, 22x, 22x, 22x, 23x7, 22x 2x, 22x, 22x, 23x, 23x, 23x 23x.5, 24x, 24x, 24x, 24x, 24x.50 24x3, 25x, 25x, 25x.55, 25x, 25x, 25x, 25x. 25x3 22x, 22x, 22x, 23x 24x, 24x, 24x, 25x.00 24x, 24x, 24x, 25x 2x, 26x, 26x / pair (Lbs.) CC QG522 QG530 QG534 QG532 QG534 QG532 QG530 QG532 CROSS CHAIN Dia No. of links SC QG30005 QG30005 QG30005 QG30005 QG30005 QG30005 QG30005 QG30005 SIDE CHAIN Dia No. of links (outside) d: pair per bag Order unit: Pair This is only a partial listing of tire size applications. For complete, uptodate listings, please refer to SCCʼs most current Winter Traction Product Tech Guide & Tire Size Directory, or visit Catalog weights are approximate Minimum order quantity: Pair 37

138

139 Section 6 Traction Product Spare Parts Replacement Crossmembers Tighteners Fasteners and Hooks Bulk Side Chain... 4 Tools Section 7 Misc. ZProduct P.O.P. Displays... 5 Tire Chain Identifier Traction Product Packaging Specs 5455 Index (by part number)

140 TRACTION PRODUCTS ZChain Replacement Crossmember Use on final assembly # Overall length per ctn (Lbs) packaging Z30 Z bags per ctn Z34 Z bags per ctn Z3 Z555, Z bags per ctn Z30 Z bags per ctn Z34 Z575, Z bags per ctn Z3 Z bags per ctn d: 2 per poly bag with header card Order unit: Pair Spare Parts Shur Grip Z & Super Z LT Replacement Crossmember SZ334 SZ336 Use on final assembly # SZ35 SZ3 Overall length per ctn (Lbs) SZ Series ZT Series packaging 6 bags per ctn 6 bags per ctn SZ33 SZ323, SZ327, SZ bags per ctn SZ340 SZ bags per ctn SZ342 SZ335, SZ bags per ctn SZ344 SZ bags per ctn ZT742 ZT72, ZT bags per ctn ZT744 ZT bags per ctn ZT746 ZT747, ZT bags per ctn d: 2 per poly bag with header card Order unit: Pair Super Z Single Replacement Crossmember Use on final assembly # Overall length per ctn (Lbs) packaging ZT25 ZT per carton ZT26 ZT37, ZT per carton ZT263 ZT53, ZT5, ZT65, ZT6, ZT per carton ZT265 ZT77, ZT7, ZT per carton ZT267 ZT, ZT per carton ZT26 ZT per carton ZT275 ZT per carton ZT277 ZT per carton ZT23 ZT per carton d: Bulk Super Z OTR Replacement Crossmember Use on final assembly # Overall length per ctn (Lbs) packaging ZT532 ZT per carton ZT54 ZT per carton ZT543 ZT per carton ZT545 ZT per carton d: Bulk 40 Minimum order quantity: package Catalog weights are approximate

141 TRACTION PRODUCTS Super Z QuikDraw Dual Triple Replacement Crossmember Use on final assembly # Overall length per ctn (Lbs) packaging ZT32 ZT per carton ZT33 ZT per carton ZT34 ZT per carton ZT35 ZT70, ZT per carton ZT36 ZT per carton d: Bulk SUPER Z CROSSMEMBER REPAIR: Spare Parts Lay the chains down with the flat side of the eyelets (Marked TIRE SIDE) towards the ground. Open the eyelet flap (about 20º30º) and take the old crossmember out through the hole in the flat side of the eyelet. Insert the new crossmember through the hole in the flat side of the eyelet. Close with a hammer and make sure that the crossmember is securely seated in the eyelet. Alloy Radial Chain Replacement Crossmember Use on final assembly # Overall length per ctn (Lbs) packaging TC6 TA3, TA per carton TC65 TA per carton TC6 TA per carton TC623 TA47, TA per carton TC627 TA per carton TC637 TA per carton TC63 TA per carton TC754 TA33, TA per carton TC75 TA per carton TC762 TA per carton TC766 TA per carton TC770 TA per carton d: Bulk Catalog weights are approximate Minimum order quantity: package 4

142 TRACTION PRODUCTS Quik Grip standard link Square rod alloy Quik Grip Regular Link & Square Rod Replacement Cross Chain with End Hooks (Bulk packaging) Number of links Diameter of links Inside length cross chain with end hooks Cross chain end hook number per bag (Lbs) packaging QG544 7 / QG / bag QG54 / QG / bag QG5420 / QG / bag QG5422 / QG / bag QG6046 5mm x 5mm / bag QG mm x 5mm / bag QG mm x 7mm 5.75 QG / bag Spare Parts QG655 QG62 QG622 QG mm x 7mm 5/64 5/64 5/ QG2054 QG2005 QG / bag 50 / bag 50 / bag 25 / bag QG6225 5/64 5. QG / bag QG6226 5/ / bag QG /64 6. QG / bag QG /64 7. QG / bag QG625 / QG / bag QG6253 / QG / bag QG6255 / QG / bag QG6256 5/ / bag QG625 /32. QG / bag QG6260 5/ / bag QG6263 5/ / bag QG / QG / bag QG6266 5/ / bag QG / bag QG / bag QG / bag QG / bag QG QG / bag QG6630R QG / bag QG / QG / bag QG6650 7/ QG / bag QG / QG / bag QG / / bag QG / / bag QG / / bag QG / / bag QG QG / bag QG QG / bag QG / QG / bag QG / QG / bag d: Bulk Note: These items are also packaged in retail poly bags. See page 43 for details Minimum order quantity: package Catalog weights are approximate

143 TRACTION PRODUCTS Quik Grip Replacement Cross Chain with End Hooks (Retail packaging) Number of links Diameter of links Use on final assembly # per ctn (Lbs) packaging QG Type PL, 4,, bags per carton QG Type PL 6, bags per carton QG Type PL 34, bags per carton QG Type PL bags per carton QG6230 Type LSH 220, bags per carton QG62230 Type LSH 224, 226, 22, bags per carton d: 2 per poly bag with header card Order unit: Pair Quik Grip VBar Replacement Cross Chain with End Hooks (Bulk packaging) Spare Parts Number of links Diameter of links Inside length cross chain with end hooks Cross chain end hook number per bag (Lbs) packaging QG520 QG522 QG530 QG532 QG6 QG62 QG622 QG625 QG626 QG653 QG65 QG660 QG663 QG666 QGV535 QGV5340HD QGV /64 3/64 3/64 3/64 5/64 5/64 /32 5/64 /32 /32 /32 5/6 5/6 5/6 /32 5/6 5/ QG20050 QG20050 QG20056 QG20056 QG2005 QG2005 QG20053 QG2005 QG20053 QG20053 QG / bag 25 / bag 25 / bag 25 / bag 50 / bag 50 / bag 50 / bag 50 / bag 50 / bag 50 / bag 50 / bag 25 / bag 25 / bag 25 / bag 50 / bag 25 / bag 25 / bag d: Bulk Note: These items are also packaged in retail poly bags. See below for details. Quik Grip VBar Replacement Cross Chain with End Hooks (Retail packaging) Number of links Diameter of links Use on final assembly # per ctn (Lbs) packaging QG Type RP 30, bags per carton QG Type RP 50, bags per carton QG630 Type LRS 20, bags per carton QG6230 Type LRS 24, 26, 2, bags per carton d: 2 per poly bag with header card Order unit: Pair Catalog weights are approximate Minimum order quantity: package 43

144 TRACTION PRODUCTS Quik Grip Alloy Stud Chain Replacement Cross Chain with End Hooks Number of links Diameter of links (mm) Inside length cross chain with end hooks Cross chain end hook number per bag (Lbs) packaging QGS340HD QG / bag OGS355HD QG / bag d: Bulk Quik Grip Replacement Cross Chain for Twin Grip Tractor Chain Number of links Diameter of links Inside length cross chain w/ end hook Cross chain end hook # per bag (Lbs) package Spare Parts QG330 QG350 QG / bag / bag / bag : Bulk Whitestar Alloy Replacement Cross Chain Number of links Used on final assembly # per bag (Lbs) package WS553 7 WS / bag WS557 7 WS605, WS / bag WS56 7 WS / bag WS WS / bag WS WS6, WS / bag WS75 5 WS / bag WS WS / bag : per poly bag Diamond Blue Replacement Cross Chain Number of links Diameter of links (mm) per bag (Lbs) package DB x / bag DB x / bag : Bulk Shur Grip Z, Super Z LT, Super Z6 & Super Z Rubber Tightener (2 tighteners per bag) Size (mm) Used on final assembly # per ctn (Lbs.) package SZ72.5 x 3 SZ5 ~ SZ37, SZ35 ~ SZ bags/ctn SZ74 x 60 SZ3, SZ43, SZ33, SZ343, SZ42, ZT bags/ctn SZ76 x 5 SZ435, SZ44, SZ447, SZ45, ZT735, ZT74, ZT747, ZT bags/ctn SZ0 x 226 SZ456 ~ SZ bags/ctn : 2 per poly bag Order unit: Pair 44 Minimum order quantity: package Catalog weights are approximate

145 TRACTION PRODUCTS Shur Grip Z, Super Z LT, Super Z6 & Super Z Replacement Tightener Hooks Super Z Dual/Triple Center Draw Chain Fastener SZ6 Size: Fits.5mm & mm hoops / Bag: 0.60 Lbs. d: / bag : 6 bags / ctn SZ Size: Fits mm hoops / Bag: 0.3 Lbs. d: 4 / bag : 6 bags / ctn ZT70 / Ctn: 2.00 Lbs. d: Bulk : / ctn Super Z Rubber Tightener (2 tighteners per bag) Size (mm) Used on final assembly per carton (Lbs.) package ZT6 ZT70 ZT74 ZT75 x 270 x 300 x x 400 Custom ZT, ZT7, ZT7, ZT ZT Custom bags/ctn 6 bags/ctn 6 bags/ctn 6 bags/ctn Spare Parts ZT x 450 ZT, ZT32, ZT4, ZT43, ZT bags/ctn ZT7.5 x 3 Custom bags/ctn ZT2 x 5 ZT35, ZT37, ZT4, ZT53, ZT5, ZT65, ZT6, ZT77, bags/ctn ZT, ZT2, ZT6 d: 2 per poly bag Order unit: Pair Super Z Replacement Tightener Hooks ZT07Y / Ctn: 2.00 Lbs. d: Bulk : 25 / ctn ZT07B / Ctn:: 2.00 Lbs. d: Bulk : 25 / ctn ZT07R / Ctn: 2.00 Lbs. d: Bulk : 25 / ctn ZT07K / Ctn: 2.00 Lbs. d: Bulk : 25 / ctn Whitestar Alloy Rubber Tightener (2 tighteners per bag) Size (mm) Used on final assembly per carton (Lbs.) package WS222 x 60 WS604, WS605, WS bags / ctn WS223 x 5 WS60, WS6, WS bags / ctn WS224 x 226 WS64, WS705, WS bags / ctn d: 2 per poly bag Order unit: Pair Whitestar Alloy Replacement Tightener Hooks Diamond Blue Side Chain Hold Down WS275 Size: All Whitestar Alloy Tensioners / Bag: 0.50 Lbs. : 50 / ctn DB70 Size: All Diamond Blue Product / Ctn:.50 Lbs. : 50 / ctn Catalog weights are approximate Minimum order quantity: package 45

146 TRACTION PRODUCTS Quik Grip Link Chain & TA Alloy Radial Duals Rubber Tighteners Description Used on per ctn (Lbs) package QG20030 Rubber w/ 4 hooks Medium garden tractor, snow blower 4.00 bags / ctn QG20032 Rubber w/ 4 hooks Large garden tractor, snow blower & ATV 4.00 bags / ctn QG2006 Rubber w/ 5 hooks Truck link, TA Super Singles, TA Dual 6.00 bags / ctn QG20070 Rubber w/ 5 hooks Passenger link bags / ctn QG20070 Rubber w/ 5 hooks Passenger link 5.00 bags / ctn QG20074 QG20074 Rubber w/ 5 hooks Rubber w/ 5 hooks Light truck link Light truck link bags / ctn bags / ctn QG20030 & QG20032 QG2006, QG20070 & QG20074 d: 2 per poly bag Order unit: Pair Spare Parts Quik Grip Link Chain Rubber Tightener Metal Hook QG20075 QG2007 QG2007 d: Bulk Used on assembly # QG20070 QG20074 QG2006 Rod diameter Inside length per bag (Lbs) package 0 / bag 0 / bag 0 / bag Quik Grip Link Chain Spring Tighteners Description Used on # Springs per tightener per ctn (Lbs) package QG2004 Ring and springs ATV 4.00 bags / ctn QG2007 Chain and springs Light truck link boxes / ctn QG20072 Chain and springs Medium truck link boxes / ctn QG20073 Chain and springs Large truck link boxes / ctn d: pair per box Order unit: Pair QG2004 QG2007, QG20072 & QG20073 CAM with long link Use on: per bag (Lbs) package QG2002 Light truck ( side chain) / bag QG2003 Truck ( & side chain) / bag d: Bulk Cam Tightening Tools (For Quik Grip and Diamond Blue) QG200 Size: For light truck CAM /Bag:.50 Lbs. : Bulk : / bag QG2005 Size: For truck CAM /Bag: 3.30 Lbs. : Bulk : / bag 46 Minimum order quantity: package Catalog weights are approximate

147 TRACTION PRODUCTS Super Z Inside Fastener Speed Hook Use on final assembly # Rod diameter Inside length per ctn (Lbs) package ZT02 All ZT00 stock # s / carton ZT03 d: Bulk All ZT0 & ZT00 stock # s / carton TA Alloy Radial Chain Fastener Repair Kit TA04 d: One kit per bag Use on final assembly # Description per ctn (Lbs) All TA truck chains Complete fastener kit for /2 pair package kits / carton Spare Parts QG20060 QG2006, QG20062 & QG20062XL QG20064 QG20063 & QG20065 QG20066 QG2006 Quik Grip Link Chain Side Chain End Fastener Type per bag (Lbs) package QG20060 RP passenger & light truck / bag QG2006 HD CAM truck (with keeper link) / bag QG20062 CTO truck (with keeper link) / bag QG20062XL Stud chain / bag QG20063 Light truck / bag QG20064 PL passenger / bag QG20065 /32, 5/6 side chain / bag QG20066, 7/6 side chain / bag QG2006 /32, 5/6 with clevis attachment 5.00 / bag d: Bulk Catalog weights are approximate Minimum order quantity: package 47

148 TRACTION PRODUCTS Quik Grip Link Chain Inside Fastener Speed Hook Use on final assembly # Rod diameter Inside length per bag (Lbs) package QG2000 RP, LSH, LRS / bag QG200 PL / bag QG2004 SH, RS, DH, DTH, RDT / bag QG2005 FTH, SM, DTM, OTR, CTO / bag QG2006 CAM, CAM HD / bag QG2007 CTO / bag QG206 Alloy Square Rod Truck / bag d: Bulk Spare Parts Cross Chain End Hook Rod diameter Type Inside length per bag (Lbs) package QG / RP / bag QG2005 / LSH, RLS, DH / bag QG /6 DHLT TRUCK, RS RDT, LSM, / bag DTH, SH, CAMSH, CAMDTH DH, SM, DTM, OTR, CAMHD, / bag TWIN GRIP, RDT, RS, CTO QG / FTH, OTR / bag QG PL / bag QG / FTH / bag QG2005 7/ OTR / bag QG2005 7/ OTR / bag QG2054 5/6 ALLOY SQUARE ROD TRUCK / bag d: Bulk Side Chain End Lap Repair Links Rod diameter Type Inside length per ctn/bag (Lbs) package H RP, Passenger / ctn H Light truck / ctn H025 Truck / ctn H02 Truck, Large truck / ctn H020 OTR, Mud service truck / ctn QG PL, RP Passenger (Vshaped) / bag QG500* PL, RP Passenger (Vshaped) bags per ctn d: Bulk *Note: Retail packaged 4 per bag 4 Minimum order quantity: package Catalog weights are approximate

149 TRACTION PRODUCTS Quik Grip Cross Chain Repair Link (Self closing) Rod diameter Finish Description per ctn/bag (Lbs) package QG Bright zinc All passenger / bag QG Lacquer Light Truck / bag QG2002 Lacquer Truck.00 0 / bag QG5* Bright zinc All passenger 2.40 bags / ctn d: Bulk *Note: Retail packaged 4 per bag Straight Link Welded Side Chain (Nonhardened) QG30005 Rod diameter 5/ Trade size Finish Bright Zinc Type PL Inside length.25 per bag (Lbs).00 package 0 ft / bag QG30020 QG30040 QG30060 QG /6 7/32 /32 / /0 4/0 6/0 6/0 Lacquer Lacquer Lacquer Lacquer RP LSH, DH, RLS CAM, LSM, RS, RDT, DH, SH, DTH CAM HD ft / bag 0 ft / bag 0 ft / bag 0 ft / bag Spare Parts QG /6 7/0 Lacquer SM, DTM, OTR, FTH, CTORS ft / bag QG3000 /0 Lacquer FTH, OTR ft / bag QG300 7/ /0 Lacquer OTR ft / bag QG3060 /32 6/0 Yellow Zinc For QG20 & QG40 Series ft / bag QG /6 7/0 Yellow Zinc For QGS Series Stud Chain ft / bag d: 0 Feet per bag, except 50ft/bag Order unit: Bag Square Rod Alloy Welded Cross Chain (Casehardened) Rod diameter (mm) QG3260 7mm SQ d: 50 Feet per bag Inside length per bag (Lbs) package Finish Type Yellow zinc For QG20 / 40 Series ft / bag Order unit: Bag Twist Link Welded Cross Chain (Casehardened) Rod diameter Trade size Finish Type Inside length per bag (Lbs) package QG /64 4/0 Lacquer Light truck ft / bag QG32060 /32 6/0 Lacquer Light truck, Truck ft / bag QG /6 7/0 Lacquer Light truck, Truck ft / bag QG3200 /0 Lacquer Truck, Tractor ft / bag QG320 7/ /0 Lacquer Tractor, OTR ft / bag d: 50 Feet per bag Order unit: Bag Diamond Blue Welded Side Chain (Nonhardened) DB30005 d: 0 Feet per bag 0.7 Rod diameter 3/6 Finish per bag (Lbs) package Catalog weights are approximate Minimum order quantity: package 4 Type Inside length Blue Powdercoat For DB20 Series (Diamond Blue) ft / bag Order unit: Bag

150 TRACTION PRODUCTS Traction product tools Super Z Tightener Installation Lever ZT7 : 0.0 Lbs. /ea. : / sleeve Super Z Repair Plier ZT3 : 7.00 Lbs. /ea. : / box To ols Passenger Link Chain Repair Plier QG200 : 0.40 Lbs. /ea. Packaging: / bag with header Light Truck Link Chain Repair Plier QG2004 :.25 Lbs. /ea. Packaging: / box Truck Link Chain Repair Plier (33 ) QG2003 :.0 Lbs. /ea. : / box Truck Chain Plier Replacement Jaws QG2002 Application: Jaws for QG2003 : 3.00 Lbs. /ea. : / box Chain Cutters All types See page Alloy Radial Chain Repair Tool Kit TC3 : 4.50 Lbs. /ea. : kit / box ICEMAN ICE SCRAPER: SCCʼs Iceman ice scraper not only does a great job cleaning ice and snow off the windshield, but can also assist in installing tire chains. The cutaways near the scraper end can be used to pull the chain around the tire during installation. Great promotional giveaway item Only long, so it conveniently stores in door pockets for easy access. 4 color sleeve with punch hole for hanging from peg board. ES2000 : 0.5 Lbs./ ea. : / carton 50 Minimum order quantity: package Catalog weights are approximate

151 MISCELLANEOUS Z Product display and Point of Purchase Materials Beginning with a truly practical display tire, SCC offers the necessary material to display Z traction products effectively and attractively in a retail environment. Point of Purchase WS07 (Shelf stand) WS03 (Display tire) / WS05 (Adjustable display stand) ADZSign (30 x 60 Outdoor banner) ADSign (30 x 60 Outdoor banner) ADZWindow (3 x 27 Static cling window banner) Winter Traction Product Tech Guide & Tire Size Directory SCC Tractor Chain CutDown Chart Catalog weights are approximate Minimum order quantity: package 5