# 856A1300G LENGTH GAGE-CORE MODULE

Transcription

1 Tool No. S/N Description Remarks Dept. ATA # 856A1009G Adapter, vertical lift CFM # 856A1015G Sling frames, 3 legs CFM # 856A1020G Restraining core module CFM # 856A1021G Fixture lift/turn comp CFM # 856A1042G Wrench torque #4 brg. ret CFM # 856A1057G Fixture lift/turn HPT CFM # 856A1061G Fixt. lift/turn HPTR disk CFM # 856A1073G Truck HPTR Horizontal Transport and store HPT rotor # 856A1083G Fixture lift/turn core CFM # 856A1102G Fixture horizontal lift CFM # 856A1103G Fixture lift HPT nozzle CFM # 856A1107G Fixture lift core module CFM # 856A1125G Fixture lift horizontal CFM # 856A1157G Fix. lift Adj. CF CFM # 856A1196G Fixture lift/turn comb. CFM # 856A1300G LENGTH GAGE-CORE MODULE TO MEASURE OVERALL LENGTH OF CORE MODULE PRIOR TO INSTALL # 856A1313G Ring support eng. handlin CFM # 856A1314G Bracket set LPT aft mount CFM # 856A1332G Fixt. lift/turn core fwd. CFM # 856A1335G Bracket set HPC CFM # 856A1354G Bracket set handling core CFM # 856A1377G Fixt. lift/turn HPTS/LPT CFM # 856A1421G Fixture lift top case HPC CFM # 856A2543G LPT Shaft Centering Fixt. CFM # 856A2549G TURB.FRME HANDLG. SEGMENT TO HANDLE THE TURBINE FRAME # 856A2627G LIFTING BEAM LIFT LPT MAJOR MODULE, 1-2 BOOSTER SPOOL, FAN DISK,LPT CASE # 856A2645G Beam CG engine handling CFM # 856A2646G Turbine frame Dolly CFM # 856A3111G Dolly Trunion Fan Frame module # 856A3373G LPT BLADED DISK FIXTURE TO HANDLE THE LPT STAGE 1-4 DISK AND BLADES # 856A3387G LPT LIFT & TURN FIXT. TO TURN THE LPT CASE 180 DEGREES # 856A3503G Fixt. booster rotor assy. CFM # 856A3510G ADAPTER, 1-2 SUPPORT TO SUPPORT, LIFT AND TURN 1 AND 2 BRG SUPPORT # 856A3532G FIXT. LIFT & TURN FAN FRM TO PERMIT LIFTING AND TURNING OF FAN FRAME MODULE # 856A3533G FAN INLET 3 LEG SLING TO HANDLE FAN INLET CASE OR FAN FRAME ASSEMBLY # 856A3538G FIXTURE, HNDLNG FAN DISK TO HANDLE THE FAN DISK WITH TWO YOKES AND A STRAP # 856A3540G FIXT.HNDLNG/TURN BSTR SPL TO LIFT AND HANDLE THE BOOSTER SPOOL # 856A3596G LIFTING BEAM, FAN FRAME TO HANDLE THE FAN MAJOR MODULE

2 # 856A3767G FIXT. HNDLNG LPT RTR/STTR TO LIFT AND TURN THE LPT MODULE # 856ATT Lifting Eye Fan Frame Assy # 856ATT Lifting Eye Fan Frame #*856A3519G AGB - 3-LEG SLING TO HANDLW AGB OR AGB EQUIPPED WITH FUEL PUMP & MEC *856A1404P14 AT3532 TOOL, ADAPTER PLATE HPT B Adapter for Tool 856A1404 to HPT rotor front shaft A1000G WRENCH #3 LOCKING NUT TORQUE/LOOSEN & TURN IGB #3 LOCKING NUT DURING ASSY/DISSY A1001G01 AT3472 WRE KEY TRCH MULTIPLIER DEC EFFORT REQ TO SPPLY INPUT TRQ TO SWEENEY TORQ MULTIPLIER A1005G Wrench, compressor rotor CFM A1006G Wrench torque adapter CFM A1007G Support dummy comb case CFM A1008G Fixture, lift & Turn HPTR CFM A1008G FIXT.HPTR AFT END To lift and turn HPT and HPC during assy and dissy A1010G Wrench, rachet comp. roto CFM A1012G Lever, countertorque comp CFM A1013P01 AT3488 VSV HOLDER To apply countertorque to the Comp Stator Vanes from inside A1016G Stand Compressor Rotor To support compressor rotor & HPT rotor in Vert. position A1017G Puller, Impact-HPT Shroud CFM A1017G PULLER HPT SHROUD TO REMOVE HPT SHROUD SEGMENTS A1018G03 AT3483 Stand Subasembly-Frame To support the combustion case during overhaul operations A1019G FIXT.VRTCL LIFT COMB CHMB TO LIFT AND TURN THE COMBUSTION CASE A1022G Wrench set spanner air CFM A1023G DR NUT STRT COMP RTR 3,4 START NUTS ON BOLTS THAT SECURE STAGE 4-9 SPOOL,STAGE A1025G LOCATOR, SEAL WIRE COMP. TO LOCATE AND ESTABLISH THE ENDS OF THE COMPR SEAL WIRE A1028G LIFT FIXT.CPR STG 1-2 SPL TO LIFT AND TURN THE 1-2 OR 4-9 COMP. SPOOL A1033G Puller #3 brg. gear CF A1034G Wrench 35-tooth bevel gr. CFM A1035G Fixture, hold #3 brg. IGB CFM A1037G Wrench, puller ring IGB CFM A1039G Adapter IGB to pwr arm CFM A1040G Removal IGB brg. & Spacer CFM A1045G Wrench #3 bearing retaine CFM A1046G Wrench #3 brg rotating se CFM A1047G Fix. hold IGB module CFM A1048G Table antitorque IGB Mod. CFM A1049G Puller #3 bearing inner r CFM A1051G Puller arm comp. stator CFM A1052G PRECISION B/U HPTR TO MEASURE THE R/U OF THE HPTR MATING PARTS DURING ASSY

3 856A1054G Tool set inst/rem IGB/#3 CFM A1055G FIXTURE SET, GRIND SPACER To hold the stator liners in proper position during grinding A1058G COMP. BLADE VIBRATOR TO ASSIST IN THE REMOVAL OF THE STAGE 4-9 BLADES A1063G TOOL SET-COMP STTR& LINER TO INSTALL AND REMOVE COMP. STATOR AND LINERS A1063G TOOL SET-CMPSSR LINER To install and remove the HPC vane sectors and liners A1063G Tool Set Compressor Stato To install and remove the HPC vane sectors and liners A1068G GAGE LKG LUG COMP ASSY TO INSPECT THE COMPRESSOR BLADE LOCKING SCREWS FOR INSTALL A1069G01 AT3485 Bracket,Trunnion CombCase To support the combustion case during the subassembly stand A1069G BRACKET TRUNN.,COMB CASE TO SUPPORT THE COMB CASE DURING OVERHAUL A1070G02 AT3482 Fixture, Spline Bolt Remv To Install & Remove HPT Inner Nozzle Support attaching bolts A1071G04 AT3498 Tool set liner vanes To remove stg 6-9 liners and stg 6-8 vane segments A1072G04 AT3497 Truck HPCR To store and transport the compressor rotor assembly A1075G FIXT-LIFT HPTR DISK USED TO LIFT AND TURN THE HPTR TO THE HPC A1076G Fix, Chilling To hold dry Ice in the Flange of the HPT disk A1081G Core Module Horiz. Stand CFM A1082G01 AT3471 FIXT. LIFT HPTR VERTICAL TO LIFT THE HPTR IN THE VERTICAL POSITION TO ACCESS THE HPCR A1084G CART STATOR ACTUATOR POSITION VARIABLE STATOR VANES & VARIABLE BLEED VALVES A1085G Lift Bar Main Engine Section fit with 856A A1086G Stand Assy, CORE SECTION VERTICAL ASSY/DISSY CORE SECTION A1086G STAND ASSY-CORE SECTION TO SUPPORT THE CORE ENGINE FOR VERTICAL ASSEMBLY/DISASSEMBLY A1088G04 AT3477 SUPPORT&ROTATION-CORE ENG TO SUPPORT AND PROVIDE COUTERTORQUE FUNTION TO THE CMPR A1089G Adapter HPTR to compr. CFM A1089G BRACKET-TRUN. CMB CHMB TO SUPPORT THE COMBUSTION CASE ON THE SUBASSEMBLY STAND A1090G INSTALLER - HPT NOZ SGMT To insert the seal retaining pins in the HPT nozzle A1092P HOLDING FIXT.HPT SEAL TO HOLD THE HPT AFT SEAL AND SUPPORTS DURING ASSEMBLY A1093G02 AT3484 Fixture,Lift To remove/install combustion chamber & HPT inner fwd Nz supp A1093G03 AT3499 LIFT FIXT-COMB CHMBR TO REMOVE/INSTALL COMB. CHAMBER AND THE HPT NOZZLE SUPPORT A1094G Adapter Holding To position the HPT nozzle vertically and enable to rotate

4 856A1095G Fixture HPT nozzle assy. CFM A1099G01 AT3467 FIXT-INSTL-REMVL HPT AFT TO INSTALL AND REMOVE THE HPT AFT SHAFT A1100G DRIVER, RTNR PIN HPT NZLE To install the HPT Nozzle outer support retaining pins A1106G Pin set, guide core CFM A1114G01 AT3491 Brkt Support Manifold Support the fuel manifold on combustion case during assembly A1117G02 AT3487 Fixture, Lift HPTR, HORIZ To provide an interface b/w HPTR assy the general lift fixtu A1123G Guide fan frame/core CFM A1126G DRIVER-GUIDE STRIPS CMPSR To install the forward &Aft guide sectors in the CMPSR A1126G DRIVER-GUIDE STRIPS CMPSR To install the forward &Aft guide sectors in the CMPSR A1127P Protector HPT Shroud LPT To support the HPT stator shroud & protect fwd flange bolts A1130G07 Tool set jackscrew CFM A1130G09 Tool set jackscrew CFM A1130G10 Tool set jackscrew CFM A1132G FIXTURE, RESTRAIN-HPT RTR To hold the HPT blades radially outwrd durg blade grinding A1133P Tool rmv bld rtnr aft CFM A1136G02 AT3494 ADPT,NO.4 BRG Adapt No.4 BRG retainer wrench and core module A1140G Fixture support core mod. CFM A1145P02 AT3490 Fix,Inst. Outer Air Duct To Install the Air Duct in to the LPT support & Nozzle Sgmt A1145P FIXTURE INSTALL OUTR COOL TO INSTALL THE AIR DUCT TO THE LPT SUPPORT AND NOZZLE SEGMT A1146P FIXT. INSTL INNER DUCT TO INSTALL THE INNER DUCT TO THE LPT NOZZLE ASSY A1147G TOOL-RADIAL POSITION To set the proper radial position of 5TH STG MANIFOLD A1154P SETUP MASTER CMPR BUILDUP TO SETUP THE ROTARY TABLE & CHUCK USED FOR COMPR BUILDUP A1172G wrench set #3 brg. CFM A1195G02 AT3486 Fixture Assy HPC Sgt 1&2 To support the compressor rotor fwd shaft assy sty 1&2 spool A1198G Pullar aft shaft CFM A1204G Fixt. remove HPCR spool CFM A1206G CDP SEAL GAGE RUNOUT TO PROVIDE FIR OF THE CDP SEAL TO DETERMINE IF SEATED A1211G Fix Clamping #3 Brg Assy To eliminate movement in the IGB provide measuring surface A1216G Pull. #4 brg. Otr. race CFM A1219G HEATER-HPT AFT SHAFT A1219G02 AT3537 Heater,HPT AFT Shaft To heat the HPT aft shaft prior to No. 4 bearing outer race

5 856A1220G Tool set inst/rem HPT CFM A1225G HPTR BUILD FIXTURE BASE FIXTURE USED TO BUILD HPTR & RUNOUT TOOL A1241P DESICCANT DRYER TO SUPPLY FILTERED AIR TO THE HIGH COMPRESSOR A1265G HEATER BEVEL GEAR IGB TO HEAT THE IGB BEVEL GEAR BORE PRIOR TO INSTALLATION A1266G COMP CASE ALIGNMENT PIN TO PROVIDE CORRECT ALIGNMENT OF CASES DURING ASSEMBLY A1281G02 AT3492 Fixt Lift HPT Vertically lift front outer sealon and off the STG1 HPT Disk A1284G Puller pin HPT nozzle CFM A1290G FIXT. RUNOUT CORE MOD. TO CHECK THE RUNOUT ON THE CORE ON THE 1088 FIXTURE A1293G Retainer set comb. inner CFM A1295G FIXT. ALIGN CDP SHIELD TO PROVIDE ALIGNMENT TO THE CDP EROSION SHIELD DURING INSTAL A1299G Fixture blade removal CFM A1308G Puller HPTR Fwd Out. Seal CFM A1334G FIXT BLDUP CORE EN HP COM FIXT SUPPS CORE MAJ MOD MAINTAINS MOST AFT STACK POSITION A1342G FIXT. PRESEAT VSV ARM FIXT. IS USED TO PRESEAT THE VSV LEVER ARMS DURING ASSEMBLY A1344G FXT SETUP CRE ENG/HP COMP SETUP FIXT USED TO SETUP/CHECK CORE ENGINE HP COMP ROTOR BLD A1356G LIFT TOOL COMPR STG 1-2 LIFT FIXTURE TO BE USED TO LIFT & TURN THE STG 1-2 SPOOL A1358G01 AT3496 Fix Ins/Rem MOD 12 Fixture to installed and remove the MOD A1360G TOOL SET RUNOUT-HPT SHROU RUNOUT TOOL TO GET MEASUREMENTS OF COMP CASE A1363G Guise assy fan/core mod. CFM A1369G FIXT. ADAPTR-LINIGAGE THE ADAPTER COMMUNICATES HPC & HPT ANGULAR DATA A1371G CART,COMPUTER LINI GAGE TO PROVIDE STORAGE,TRANSP, AND BENCH FOR 856A1360 & A1372G GAGE - ARM BOW USED TO MEASURE THE HPT OUTER SEAL A1375G Fix. Core-Turning To manually turn the core during CDP bore runout A1378G BOLT RETAINER SET TO PREVENT THE BOLTS FROM MOVING DURING INSTALL HPTR TO HPC A1380G Puller outer ducts LPT CFM A1381G PULLER OUTER AIR DUCTS TO REMOVE AIR DUCTS FROM HPT/LPT OUTER AIR DUCTS A1382G01 AT3520 STUD PROTECTOR,HPT SHROUD To protect the forward flange slabbed-head bolts DURING ASSY A1384G Tool Rem. HPT shroud clip CFM A1386G LIFT FIXTURE-CORE

6 856A1388G GUAGE, SEATING CHECK To check seating between core module and IGB A1389G01 AT3493 Fix Install No.4 BRG To install No.4 BRG outer race into the HPT rear shaft A1394G FIXTURE LIFT A1403G PROTECTOR SET HPT NZL To protect the FWD & AFT ends of HPT NZL VNS DRG STRG A1404G FIXT PREC BLDUP/RUNOUT TO MEAS RUNOUT OF HP TRBN ROTORS MATING PRTS/ASSBLY HP TURB A1409G FIXT,TORQUE HPTR FRT SHFT BTO BREAK AWAY TORQUE ON HPTR FWD SHFT AND AIRSEAL A1411G PUSH/PULL FIXT. HPTR TO INSTALL/REMOVE THE HPT BLADE RETAINER A1416G FIXT. BUILDUP LPT STG 1 TO BUILDUP LPT STG 1 NOZZ. BY HOLDING THE 24 VANES TOGETHER A1417G FIXTURE LIFT AND TURN HPT To lift and turn the HPTR during engine buildup A1423G05 AT3474 CORE MOD. RESTRAIN FIXT. TO RESTRAIN THE HPT ROTOR DURING INSTALL/REMOVAL A1424G FIXT.-LIFT COMB ASSY TO LIFT THE COMBUSTORS VERICALLY AND HORIZONTALLY A1431G03 AT3463 FIXT, RESTRAIN HPT NOZZLE TO RESTRAIN NOZZLE SEGMENTS OF HPT NOZZLE CIRCUMFERENTIALLY A1433G02 AT3468 TORQUE TOOL HPT STATOR TORQUE TOOL USED TO INSTALL/REMOVE HPT STATOR BUSHING A1448G FIXT. LOCATOR-HEAT SHIELD TO ORIENT & SPACE THE HEAT SHIELD SEGMENTS TO THE SHROUD SUP A1449G FIXTURE-GRNDG HPT SHROUD TO GRIND THE HPT SHROUDS AS AN ASSEMBLY DURING ASSEMBLY A1452G FIXTURE SUPPORT HPT ROTOR TO SUPPORT THE HPT ROTOR A1453G SANCHION-HPTR TO SUPPORT THE HPTR WHEN ENGINE IS VERTICAL A1454G EXTENSION SHAFT-HPTR TO EXTEND THE HPTR IN ORDER TO SUPPORT THE ROTOR A1456G TOOL SET, REMOVAL HPT BLD To remove blade dampers and assist in pulling HP blades A1467G ADAPTER FUEL MANIFOLD TO PRESSURE CHECK THE FUEL MANIFOLDS DURING ASSEMBLY A1471G BRACKET-LPT FWD FLANGE To provide support for the engine at the forward and AFT END A1479G PULLER, SEAL HPT AFTSEAL To remove the HPT AFT Rotating Seal A1481G VSV Protractor To Measure the VSV angles A1490G FIXTURE INSTL/RMVL MOD 12 TO INSTALL/REMOVE MODULE 12 AND HAVE CONCTY W/ HPT REAR SHFT A1491G BRACKET SET COMP FLNG TO PROVIDE ATTCHMENT POINTS AT THE FOWARD END OF THE CORE A1602G CHILL FIXTURE HPTR BLADE TO HOLD DRY ICE DURING DISSY OF HPT BLADE RETAINER A1603G FIXT,REM HPT AIR SEAL The fixture used to remove/install HPT airseal PST

7 856A1603G FIXT.INSTL/REM HPT SEAL FIXT TO REMOVE AND INSTALL HPT OUTER SEAL PST A1604G FIXTURE,RMVL-BOLT INNER TO REMOVE/INSTALL THE SPLINE DRIVE BOLTS A1607G01 AT3461 FIXT, LFT-COMB CHAMB/HPT TO LIFT COMB. CHAMBER IN HORIZONTAL & VERTICAL POSITION A1800G BRACKET SET-TRF FWD FLNGE TO SUPPORT TRF FWD FLNGE DURING MAINTENANCE AND STORAGE A1801G RING SUPPORT ENG HNDLG TO SUPORT THE ENGINE AT THE FWD FAN STATOR FLANGE A1802G FXT DUMMY FRWD HPT STATOR PERM INSTALLATION OF AFT CORE MODULE A1802G02 AT3470 DUMMY FIXTURE MOD 12 TO DUMMY UP MOD 12 DURING LIFT AND TURN PROCEDURE A1803G GUIDE PINS GUIDE PINS TO INSTALL THE CORE TO THE BOOSTER A1804G CORE FIXTURE LIFT AND TURN FIXTURE FOR THE CORE MODULE A1805G Guide-Fan Frame Core Mod A1807G FIXTURE,LIFT HPT STG1 NZL To lift the HPT STG1 NZL ASSY, & CMBSTN ASSY VERT/HZTL A1812G FXT ASSLY/DIS HP TUR NOZZ ASSBLE/DISASSBLE STAGE 1 NOZZLE ASSEMBLY A1816G BRACKET SET HPC CASE TO SUPPORT THE LOWER AHALVE OF THE HPC CASE DURING TOP CASE A1817G TOOL SET RETAINER BOLT TGO INSTALL OR REMOVE THE DOUBLE HEX HEAD RETAINER BOLT A1818G GAGE SEATING CHK CORE/IGB TO MAKE SURE THE FORWARD SHAFT OF HPC IS SEATED IN IGB NO A1826G FIXT. INSTALL/REMOVE #3 PULLER USED TO INSTALL AND REMOVE THE #3 AIRSEAL A1828G TORQUE FIXT. NO.4 BRG TO REMOVE THE NO.4 BRG RETAINER NUT A1830G Guide Assy To guide core during installation A1832G FIXTURE, LIFT/ROTATE CORE This tool works W/856A1423 to lift&turn the core UP,AFT&FWD A1833G FIXT. INSTL RESTRNG CLIP TO INSTALL HPT SHROUD RESTRAINING CLIPS WITH EVEN FORCE A1838G Fixt.Puller HPT Fwd SHAFT TO PULL OFF THE HPT AIRRSEAL FROM THE HPT DISK PST A1839G Fixture, Disassy-HPTR/HPC DISSY FIXTURE HPT PST A2004G TOOL ASSY,INST/REM HPTR TO INSTALL/REMOVE HPTR TO HPC BOLTS A2005G Guide - Core to Fan Modul Guide Core onto the Fan Module during Assy & Dissy A2010G Fixt. rem. HPT fwd shaft CFM A2308G SLEEVE,CNTRG REM/INST LPT To center and remove/install the LPT Major to the Fan Major A2310G FIXT.ALIGN BSTR 2 LPT SFT To align and guide respectively the booster and LPT SHAFT A2310G FIXT.ALIGN- BSTR TO LPT To align and guide respectively the booster and LPT shaft

8 856A2316G WRENCH-TORQUE LPT NUT TO TORQUE/LOOSEN LPT COUPLING NUT A2335G STOOL-ASSY/DISSY 1-2 BRG STAND USED TO DISSY/ASSY THE 1-2 BRG SUPPORT A2336G PULLER-FWD RTATNG AIR/OIL To remove the forward rotating air/oil separator A2337G PULLER-NO.1 INR RACE To remove No.2 inr race halves of No.1 ball BRG A2339G PULLER #1 BRG SLEEVE TO REMOVE THE NO. 1 BRG SLEEVE A2342G TOOL SET,PUSHERS AND ROD INSTLL:N1BRG SLEEVE,INNR/OUTR RACE, OIL BAFFL,AIR/OILSEP A2345G RING-LIFT FAN SHAFT TO LIFT AND HANDLE THE FAN SHAFT A2373G FIXTURE, TORQUE CVT NUT To torque or loosen the Center Vent Tube in the LPT Shaft TO REMOVE THE NO 5 INNER RACE FROM THE LPT 856A2374G PULLER-NO 5 BRG INNER SHAFT A2380G FIXT-CHECK CNTR VENT TUBE To control the OD & tightening of the LPT center Vent Tube A2397G CHKG TOOL-CNTR VENT TUBE To control the axial position and runout of the ctr vnt tube A2412G RING,HOLD-STG 1 STAT SEAL To hold the stg 1 outer stationary air seal during transport A2501G WRENCH-VBV MANUAL CONTROL TO MANUALLY CONTROL THE VBV SYSTEM A2504G Push Pull Ferrule Remove/Install flexible shaft ferrules from/on fan fram stru A2513G Tube dummy LPT Shaft CFM A2524G LPT Module fixture CFM A2524G01 AT3504 LPT MAJOR MOD HNDLG FIXT TO HANDLE LPT MAJOR MODULE A2524G01 AT3505 LPT MAJOR MOD HNDLG FIXT TO HANDLE THE LPT MAJOR MODULE A2528G Stand, Storage LPT Mod. CFM A2528G01 AT3502 LPT TRANSPORT STAND TO STORE AND TRANSPORT LPT MAJOR MODULE A2528G01 AT3503 LPT TRANSPORT STAND TO STORE AND TRANSPORT LPT MAJOR MODULE A2540G LPT SHFT TO MOD. BUILDUP TO ASSY/DISSY THE LPT ASSY MODULES A2542G02 AT3475 FIXT.-HOIST-LPT MODULE TO HANDLE THE LPT ROTOR/STATOR A2544G TRF DOLLY TRUNNION TO ASSEMBLE/DISASSEMBLE AND STORE THE TRF A2567G LPT Lifting Eye, Forward To handle LPT shaft or LPT major module A2568G LPT Lifting Eye, AFT To handle LPT shaft A2571G Pins guide #1 & #2 Brg. CFM A2573G Adapt pull LPT Shaft plug To remove LPT shaft plug A2573G01 AT3535 ADAPTER, PULL - LPT SHAFT To remove LPT shaft plug A2575G Stand Storage LPT LPT A2576G SPACERS,SPPT-LPT RTR/CASE To maintain LPT rotor centered in LPT case A2577G01 AT3452 ring location #5 brg role jet cell A2600G05 AT3450 LPT SFT GUIDE/STOP TOOL STOP MAJOR MOD III DUR INSTALLATION ON ENGINE GUIDE LPT SHFT A2600G05 AT3538 LPT Shaft Guide & Stop TL To stop major module III during installation on engine A2604G Puller aft rot. air/oil CFM A2609G Block jacking fuel/mec CFM A2611G Puller LPT CFM

9 856A2616G SECTOR, CENTERING To center LPT shaft relative to fan frame drng MOD2 INST/RMV A2618G Fixture, Rotor/Stator To restrain LPT rotor in relation to LPT stator A2618G03 AT3525 FIXTURE, HOLDING -LPTR To restrain LPT rotor in relation to LPT stator A2618G03 AT3526 FIXTURE, HOLDING -LPTR To restrain LPT rotor in relation to LPT stator A2625G01 AT3473 FAN & BSTR STORAGE STAND TO STORE FAN AND BOOSTER MODULE A2626G01 AT3495 Stand Storage No.1 & No.2 To store No.1 & No.2 Brg Support module A2632G Puller Remove engine parts which have thread (250-28UNJF-3B) extrac A2634G DLLY STRG ASSY/DIS LPT SH TO STORE ASSEMBLY/DISASSEMBLY LPT SHAFT MODULE A2640G01 AT3501 TOOL SET OIL RNG SEPARATE To maintain ducts on oil ring separator during DISSY/ASSY A2642G Ring, Restraining No.5 Br To maintain pins during No.5 bumper bearing installation A2644G TOOL, HOLDING-FAN DISK TO TAKE THE RESIDUAL TORQUE FROM FAN SHAFT TO DISK A2647G Stand, Mobile Horz.Mod 3 CFM A2647G02 AT3523 PULLER,NO. 5 AGB GRSHAFT To remove Sealol seals or magnetic seals from AGB A2647G02 AT3524 PULLER,NO. 5 AGB GRSHAFT To remove Sealol seals or magnetic seals from AGB A2648G SUPPORT, REAR FAN FRAME To support the rear of the fan frame to remove supports A2655G FIXTURE RAD.DR.SHFT RADIAL DRIVE SHAFT HSG ASSY/DISSY FROM FAN FRAME STRUT A2657G Insp. Kit Central Vent tb To verify tightness of center vent tube A2660G GAUGE MEASURE AXIAL CLR To measure dimension ZA through the STG2 Nozzle A2660G GAUGE,MEASURE AXIAL LPT To measure dimension ZA through the stage 2 nozzle ASSY A2660G GAUGE MEASURE AXIAL CLEAR TO MEASURE DIMENSION ZA THROUGH THE STG 2 NOZZLE A2661G Puller aft rot. air/oil CFM A2662G Tool Kit Mast Air Nozzle To test aligment and calibrate air flow test rigs A2663G Puller splitter fairing CFM A2664G GAGE SETTING VBV DOORS To set the VBV doors in the closed position A2666G AIR TEST FIXTURE TO PRESSURE TEST THE FAN FRAME MODULE A2667G Tool Check AD2 run out To check the AD2 Circular Run Out A2667G A.D. FAN RUNOUT TOOL TO CHECK THE A.D. CIRCULAR RUNOUT ON THE FAN MAJOR MODULE A2668G KIT PULLER ADAPTERS FITTED WITH A SLIDE HAMMER USED TO EXTRACT PARTS A2676G Gauge Check Clr MO1B LPT To check clearance M A2709G01 AT3465 GUIDE FWD SUPPORT TO MAINTAIN THE AXIAL AND RADIAL POSITION OF THE LPT SHAFT A2710G FIXT. HANDLING LPT MAJOR Handling and transport of LPT Major Module A2711G FIXTURE CENTER LPT SHAFT Hold LPT shaft/lpt case while handling LPT major module

10 856A2713G FXT BLDUP LPT SHFT TO LPT ASSY/DISASSY OF MODULE 14 FROM MODULE 13/CHECK OF MAJ MODULE A2714G FXT LIFT LPT MODULE TO HANDLE LPT ROTOR STATOR AND SHAFT A2716G01 AT3451 torque dispatching ring jet cell A2721G PULLER, ROTATING AIR SEAL To separate stage 3 rotors air seal from stage 3 LPT DISK A2722G01 AT3453 fixt inst outer cooling jet cell A2722G01 AT3460 PINS, GUIDE TRF TO LPT TO POSITION TRF TO THE LPT MODULE A2727G PULLER, RADIAL DRIVE SHFT To remove/install radial drive shaft A2730G FIXT.ASSY/DISSY-LPTR To assemble/disassemble the LPT rotor/stator A2731G SECTORS SUPPORT LPT SHAFT TO REMOVE/INSTALL THE LPT SHAFT FROM THE LPT MODULE A2750G FIXTURE LPT BLDS STG 1-4 TO ALLOW DISSY/ASSY of LPT blades 1, 2, 3 and A2751G TOOL SET LOCATING PINS TO POSITION THE NOZZLE SEGMENTS IN THE LPT CASE A2752G HOOKS-RESTRAIN DSK TO LPT A2755G TOOL SET SEALS TO CONE TO INSTALL FWD AIR SEALS ON LPT STUBSHAFT A2756G DIFFUSER HEAT LPT SHAFT TO HEAT LPT SHAFT DURING ASSY OF MAJOR MODULE A2758G FIXT.CNTR LPT SHFT 2 LPT Center LPT shaft to LPT during LPT major MOD Assy A2760G RNG SUPPT CONE STUD SHAFT TO TURN OVER THE CONE STUBSHAFT & DISK 3 DURING ASSY/DISSY A2764G HEATER, LPT ASSY TO THERMALLY EXPAND THE LPT STUDSHAFT A2766G Ring Supp Cone Stub Shaft Suppt stubshaft cone during removal of STG 3 Air Seal A2772G Puller, Turbine Frame To separate the turbine rear frame from the LPT rear case A2773G SPACR SUPPT LPTR/LPT CASE TO SUPPORT LPTR TO LPT CASE DURING ASSY/DISSY A2775G PULLER, OIL SUMP ASSY TO REMOVE OIL SUMP ASSY AND AIR HEATER COVER A2780G Handling adapter To facilitate installation of tool 856A A2785G LIFT BEAM BALANCE & BSTR TO HANDLE THE BOOSTER BALANCING ASSEMBLY DURING BALANCING A2789G RING CNTRG SHFT TO AIRSEL TO CENTER THE AFT ROTATING AIRSEAL ON LPT SHAFT A2902G DUMMY FAN DISK To simulate fan disk thickness during torquing/loosening nut A2903G BEAM, TORQUE ADAPTATION To take up: Residual torque during rem/instal LPT CPLG NUT A2905G WRENCH TORQUE/FAN DISK To torque/loosen the fan disk coupling bolts A2906G GUIDE,COUNTERTORQ WRENCH To remove/install all major modules to clamp/loosen LPT nut

11 856A2912G FIXT. ASSY/DISY FAN BSTR To assy/dissy the fan and booster module and turn it over A2914G TOOL SET,DISK TO BSTR To position the fan disk on the booster spool A2915G BOOSTER SPOOL PROTECT RNG To protect booster spool at assembly/disassembly A2916G TOOL SET,GUIDE PINS BSTR To guide fan stator 1-5 vane assemblies during assy A2921G TEMPLATE,1-2 BRG TUBE To position the oil supply tubes during assembly OF TUBE A2923G GUIDE #1 BRG SUPPORT TO GUIDE THE #1 BRG SUPPORT DURING REM. OF THE STAT OIL SEAL A2943G Sleeve protection rear CFM A3011P Plug puller aft rot. CFM A3012G Puller #2 Brg. inner race CFM A3013G PULLER-N1 SPEED SENSOR RG To remove the N1 sensor ring A3017G TORQUE FIXT. #1 BRG HSG TORQUE/LOOSEN #1 BRG OUTER RACE NUT A3030G REAR FN STB SHFT LIFT EYE To handle fan stub shaft by it's rear end A3033P Nut Ret. #1 Brg. Sleeve CFM A3034G Puller Rot. air/oil Sep. CFM A3057G Fixt. torque center vent CFM A3058G PULLER #5 BRG INNER RACE To remove roller brg inner race from #5 brg A3062G PULLER,HYDR. REAR AIR/OIL To remove the rear rotating air/oil seal from LPT shaft A3070G Wrench radial drive shaft CFM A3072G Puller/pusher washer radi CFM A3074G Riverter Ball WT Booster To perform rivet flaring of fan disk balance weights A3094G BASEPLATE-ASSY/DISSY LPT TO ASSY/DISSY LPT COOLING MANIFOLDS A3097G Puller LPT stub shaft CFM A3100G PIN LOCATING CNTR VENT TO POSITION AND LOCK THE CENTER VENT TUBE TO THE LPT SHAFT A3101G PLUG,LOCATING CNTR VENT To perform angular positioning of cntr vent tube IN LPT SHAF A3104G TUBE DUMMY LPT SHAFT PLUG TO CENTER THE CENTER VENT TUBE DURING BALANCE A3108G GUIDE PIN #5 OUTER RACE TO GUIDE THE #5 OUTER RACE DURING INSTALLATION A3114G WRENCH-CAPTIVE BOLTS VBV TO PERMIT INSTALL/REMOVE NUTS OF VBV BALLSCREW ACTUATOR A3115G TOOL ADJUSTING VBV DOORS TO MANUALLY MOVE THE VBV DOORS AFTER REMOVING THE MOTOR A3234P Protector center vent tub CFM A3244G GAP CHK N1 SPEED SENSOR To check the thickness of the shim for N1 speed sensor & rin A3246G01 AT3455 Guide alignment lpt/shaft jet cell A3247G Guide align LPT shaft CFM A3253G01 Hooks restrain air seal CFM A3257G Puller fwd rot. air seal CFM A3260G Plug extractor LPT shaft CFM

12 856A3265G FIXTURE, MACHINING To permit machining of No. 5 bearing outer race sleeve A3266G GUIDE PINS-TRF TO LPTCASE TO ALIGN THE TRF TO THE LPT CASE A3267G BRG SUPT TEST RIG TO PROVIDE A MEANS TO CONNECT THE THE TEST RIG A3268G Wrench nut center vent CFM A3269G Wrench nut #5 brg. inner CFM A3272G Puller #4 brg. rot. oil CFM A3278G PIN GURDE #5 BRG SUP LPT To center No. 5 Brg Support onto turbine frame during assy A3279G Pusher/puller LPT disk CFM A3283G PLIERS, CRIMPING To crimp the straight pin for locking No.5 Brg A3308G Puller #4 Brg. inner race CFM A3315G Puller center vent tube CFM A3320G04 AT3449 LPT Assy & Dissy Jet cell A3322G Tool crimp #5 brg. nut CFM A3323G Bushing centering #1 brg. CFM A3328G TOOL SET-1&2 BRG AIR CHEK TO PERMIT AIR INLET TO OIL NOZZLES DURING IMPGMT CHECK A3329G TOOL SET TARGETS 1-2 BRG TO PERMIT VISUALIZATION OF AIR JET DURING OIL NOZZLE CHECK A3330G TOOL SET AGB/TGB NIPPLE TO INSTALL O-RINGS AND CONNECTOR TUBES A3343G TOOL SET PIN LOCATE NOZZL To locate the LPT Nozzle segments A3344G NO.1 BRG HSG PULLER TO REMOVE NO.1 BRG HSG FROM NO. 1 SUPPORT A3358G Fix Holdin No.4 Brg Race To hold No.4 brg inner race attachements bolts during instal A3358G FIXT. NO 4 BRG INNER BOLT TO HOLD THE NO 4 BRG INNER RACE BOLT DURING INSTALLATION A3383G Fixt. align LPT frame CFM A3385P Wrench stg. 1 LPT disk CFM A3386G HEATER-LPT SHAFT TO THERMALLY EXPAND THE LPT STUB SHAFT TO INSTALL IN ROTOR A3389G PULLER,ROLLER BEARING To remove radial drive shaft roller brg inner race A3392G Wrench torq. Aft Rot Air/ CFM A3409G Pins guide spinner rear CFM A3410G RING, DISTRIBUTION-TORQUE To show torque sequence of nuts SECURING LPT A3413P RING,HOLDING-NO4 BRG RLLR To hold No.4 bearing rollers during the balancing OPERATION A3415G TOOL SET CONICAL SUPPORT TO CENTER AND HOLD THE STG 3 SEAL ON THE CONICAL ROTOR SUPPT A3419G Adpt. puller oil inlet CFM A3426G PULLER, STATNARY AIR SEAL To remove the stage 1 LPT nozzle stationary air seal A3432G Gage, Tool Feelers To sheck seating of the LPT Shaft A3433G TOOL SET TRUNNIONS TO HANDLE THE LPT ROTOR STATOR MODULE A3435G ADAPTER, BLADE ROOT adapt blade root for static moment msrmnt of STG 1-4 LPT

13 856A3439G Ring, Protective Bearing To protect the locating diamenter the front of the LPT A3440G PULLER RING BRG TO EXTRACT THE PROTECTIVE BRG AFTER LPT BALANCING A3443G Puller outer race #5 Brg. CFM A3445G LPT MOD LIFT & TURN TRUNN To lift & turn LPT module A3450G FIXT BAL. LPT ROTOR STTR TO BALANCE THE LPT ROTOR STATOR AND LPT MODULE A3452G Stand Buildup vertical To assemble LPT Major Module in vertical position A3453G TRANSFER DOLLY FOR LPT TO TRANSFER THE LPT MODULE FROM ASSY TO BALANCE A3455G ADAPTER,DRIVE FWD LPT SHF drive LPT shaft during balancing A3458G BASEPLATE FOR LPT DISKS TO PROVID EFOR THE STATIC BALANCE OF THE LPT BLADED DISKS A3460G FIXT.CHK-CNTR VNT TUBE TO CHECK THE OUTERDIAMETER OF THE CENTER VENT TUBE SUPPORTS A3463G Lever countertorque LPT CFM A3473G CENTER VENT TUBE MASTER TO CALIBRATE THE CENTER VENT TUBE SUPPORTS AXIAL POSITION A3474G MASTER FOR 856A3472 TOOL TO CALIBRATE THE CENTER VENT TUBE AXIAL POSITION A3480G RING,CKNG CNTR VENT TUBE To check outer diameter of center event tube inner supports A3486G Tool Assy, Seal Cent Vent To install the damper seals on the LPT Shaft Vent tube A3487G PROTECTOR #4 BALL BRG TO PROTECT #4 BALL BEARING A3488G01 AT3464 SUPPRT HOLD FIXT,LPT SHFT FIXTURE USED TO SUPPORT LPT SHAFT DURING DISSY AND ASSY A3489G TOOL SET TARGET NO. 1BRG To perform air impingement check of the No. 1 brg oil nozzle A3500G Adpt. puller fan blade sp CFM A3501G Fixt. Aling/guide BSTR CFM A3501G ALIGNMENT GUIDE-LPT/BSTER TO ALIGN THE GUIDE BOOSTER RELATIVE TO THE LPT SHFT RMVL/INT A3502G Fixt. guide/counter torqu CFM A3504G FIXTURE,PUSHER/PULLER To remove/install module 1 and major module A3506G Wrench torque LPT Cplg. CFM A3507G GUIDE-FWD SUPPORT TO MAINT. AXIAL & RADIAL POSITION OF LPT SHAFT DRG ASSY/DISY A3508G SLEEVE,CENTERING/REMOVAL To center and remove/install module 1 and major module A3509G ADAPTER,LOCKING CORE ENG. To prevent rotation of core eng.during assy/dissy of LPT mod A3512G FAN DISK, DUMMY TO SIMULATE FAN DISK THICKNESS DURING TORQUE/UNTORQUE LPT NT

14 856A3513G BEAM, RESIDUAL TORQUE TO TAKE UP RESIDUAL TORQUE DURING ASSY/DISSY OF LPT COUP.NUT A3514P ADAPTER, RESIDUAL TORQUE TO TAKE RESIDUAL TORQUE DURING ASSY/DISSY LPT COUP. NUT A3515G EXTNTION BEAM,VAR.CG LIFT TO ADAPT VARIABLE CG LIFT FIXTURE TO MOD.1 & 2 HANDLING TOOL A3516G Sleeve Protector Fan Disk To protect the fan disk balance weights during mod 1 & mod A3517G ADAPTER, COUNTERTORQUE TO TAKE UP COUNTERTORQUE DURING MAJOR MOD.3 ASSY/DISSY A3524G BOOSTER & LPT TOOL DRIVE TO REMOVE/INSTALL BOOSTER OR LPT MAJOR MODULE A3525G CRADLE,REMOVE/INSTALL AGB TO REMOVE/INSTALL AGB OR DUMMY AGB FROM/ON ENGINE A3531G GRBX ASSY DUMMY TO HOLD THE FAN CASE DURING MACHINING OF ABRAIDABLE COATING A3539G PULLER,TIGHT BOLT BOOSTER TO REMOVE/INSTALL FAN DISK TO BOOSTER SPOOL ATTACHMENT BOLTS A3542G WEIGHT,AXIAL LDNG N3BRG simulate axial loads applied to No. 1 bearing A3543G TOOL SET, CHECK GAGE check gap between end of bolts securing FWD/ATF RET SEALS A3544G ADAPTER FLANGE-TRANS.GRBX TO HOLD THE TRANSFER GRBX DURING FINAL ASSY & SEALING TEST A3550G PULLER TOOL SET, AGB TO REMOVE BEARING FROM ACCESSORY AND TGB A3551G Tool set inst/rem TGB adp CFM A3552G Fixture holding radial CFM A3553G Fixt. lock input & horizo CFM A3555P Socket stalok nut CFM A3556G WEIGHT AXIAL LOADING NO 1 TO LOAD THE NO 1 BRG WHEN TAKING THE LHA34 DIMENSION A3558P Wrench deflector bolts CFM A3561G Wrench stalok nut CFM A3567G Tool set pads puller AGB CFM A3570G Wrench #2 Brg. inner race CFM A3571G WRENCH-FORWARD ROTATING TO TORQUE/LOOSEN FORWARD ROTATING AIR/OIL SEPARATOR NUT A3572G WRENCH,#1 BRG RACE NUT TO TORQUE/LOOSEN NO.1 BRG INNER RACE NUT A3573G03 AT3489 No.1 & 2 Brg Support To suppt No.1 & No.2 BRG Support during Assy and Dissy A3575G PULLER,#1 BRG INNER RACE TO REMOVE THE 2 INNER RACE HALVES OF THE NO.1 BRG A3576G Rem/inst. sealol/mag seal CFM A3580G FIXT. MACHINE FAN CASING To machine fan casing abradable strip A3591G PROTECTOR, MOUNTING PIN TO PROTECT THE PIN THREADS DURING ASSY/DISSY OF AGB

15 856A3600G Puller radial drive shaft CFM A3604P Wrench horz. drive shaft CFM A3606G Tools set puller pads TGB CFM A3608G Fix axial load strip Mach To pull the fan shaft or LPT shaft during abradable strip A3610G FIXT. TO CHECK DIM. "V" CHECK DIMENSION "V" AFTER ASSY OF 1-2 BRG SUPPORT A3618G TOOL SET, PUSHERS install stationary air/oil seal, oil baffle, A3621G Pin Guide To install booster stator vane assembly stage 1 on stage A3626G FRAME FRAME INSP TOOL TO CHECK ACOUSTICAL PANEL CONCENTRICITY A3628G NO.1 BRG INNER RACE TOOL TO INSTALL THE NO 1 BRG REAR INNER RACE A3702G CENTERING SLEEVE MODULE 3 TO CENTER MAJOR MODULE 3 DURING INSTALL/REMOVAL A3703G GUIDE-COUNTRTORQUE WRENCH TO PROVIDE COUNTERTORQUE DURING LOOSING OF LPT SHAFT NUT A3703G GUIDE-COUNTERTORQ. WRENCH TO PROVIDE COUTERTORQUE DURING LOOSEN/TORQUING LPT SHAFT A3704G BEAM, TORQUE ADAPTATION PROVIDE COUNTERTORQUE DURING REMOVAL & INSTALL OF LPT MODULE A3704G01 AT3536 BEAM, TORQUE ADAPTATION The tool is used to provide countertorque during assy/dissy A3706G01 AT3466 SECTOR-CTR LPT SHFT FWD TO KEEP THE LPT SHFT CENTRED DURING INSTALL/REMOVE 1-2 BRG A3707G05 AT3500 FAN BLADE SPACER PULLER TO PULL AND REMOVE FAN BLADE SPACERS A3708G01 AT3457 PUSH/PULL RADIAL DR. SHFT TO INSTALL AND REMOVE RADIAL DRIVE SHAFT A3709G02 AT3458 FIXTURE, ALIGNMT AGB TO PUT AGB IN LINE WITH THE ENGINE DURING INSTALLATION A3721G01 AT3469 ADAPTER TOOL 1-2 BRG USED TO HANDLE THE 1 AND 2 BRG SUPPORT A3722G FAN DISK DUMMY To remove or install #1 brg support on the 12-strut hub A3723G02 AT3479 FIXT. GUIDE/PULL BOOSTER TO GUIDE AND PULL THE FAN/BOOSTER MODULE DURING INSTALL/RMVL A3723G02 AT3539 FIXT. GUIDE & PULL BSTR To guide the fan and booster during install/remove A3725G TOOL SET, GUIDE PINS to guide stage 2,3 and 4 vane ASSY DURING BOOSTER ASSY A3728G CORE ENGINE LKNG ADAPTER TO LOCK THE CORE FROM MOVING DURING INSTALL/REMOVAL A3731G FIXT. HANDLING - FAN DISK The fixture is used to handle and turn the fan disk A3732G02 AT3476 HANDLNG FIXT. BOOSTER TO HOLD THE FAN&BOOSTER ASSY DURING ASSY/DISSY A3732G02 AT3533 FIXT. HANDLE FAN BOOSTER TO HOLD THE FAN&BOOSTER ASSY DURING ASSY/DISSY A3734P WRENCH,CNTRNG PIN BSTR SP LOOSEN/TORQUE BOOSTER SPOOL THREADED PIN NUT A3738G FIXT-TORQ/LOOSE #1BRG NUT TO TORQUE/LOOSEN #1BRG OUTER RACE NUT

16 856A3739G FIXTURE,INST OIL NZ BRG#2 TO install the No 2 bearing oil NOZZLE A3741G TOOL CHECKING GAP check value of gap between speed sensor ring & N1 SPD SENSOR A3746G TOOL ASSY/DISSY RAD SHFT TO ASSEMBLE/DISASSEMBLE THE RADIAL DRIVE SHAFT A3748G PROTECTION COVER -LPT DSK TO PROTECT THE STG 1 LPT BLADES DURING ASSY/DISSY A3749G TOOL SET LPT STG 2&3 SEAL TO INSTALL THE LAST SEALING PLATE DURING ASSY OF 2&3 SEAL A3750G FIXTR-CTRG LPT SHAFT MOD TO HOLD THE LPT SHAFT/LPT CASE WHILE HANDLING LPT MODULE A3750G02 AT3527 FIXT.CENTERING LPT SHAFT The tool is used to hold LPT shaft while HDLG the LPT Major A3750G02 AT3528 FIXT.CENTERING LPT SHAFT The tool is used to hold LPT shaft while HNDLG THE LPT MAJOR A3751G RING HOLDING T-1 OAS TO HOLD THE T-1 OAS IN THE LPT DURING INSTALL. OF LPT SHOUD A3752G FIXT. REML STG 1,2,3 OAS TO REMOVE THE STAGE 1,2,3 OUTER STATIONARY AIRSEAL A3755P TOOL INSTALL-LPT STG 1&2 TO ALLOW INSTALL. OF 1&2 ROTATINGF AIRSEALS DURING LPT ASSY A3756G FIXTURE, INTSLLTN SHIELD INSTALL STG 2 HEAT INSULATION PLATE IN THE LPT A3757G FIXTURE, INST SHIELD LPT3 to install the stage 3 heat insulation IN LPT A3759G02 AT3456 SECTOR HANDLING TURBINE TO HANDLE THE TURBINE FRAME MODULE A3762G FIXT.ASSY/DISSY LPTR STTR USE TO DISSY/ASSY THE LPTR ROTOR/STATOR & CHECK DISK FLATNES A3768G Wrench, Assy/DssY To torque/dissy stg 1&2 disks A3773G FIXT.-HANDLG LPT MODULE TO HANDLE AND TRANSPORT THE LPT MODULE A3773G01 AT3521 FIXT,HNDLG - LPT MAJOR The fixture is used to handle and to transport the LPT MAJOR A3773G01 AT3522 FIXT,HNDLG - LPT MAJOR The fixture is used to handle and to transport the LPT MAJOR A3778G GUIDE PINS-SPINNER CONE R TO INSTALL THE FAN RETAINING FLANGE TO THE SPINNER REAR CONE A3779G02 AT3459 PULLER PLATFORM-FAN BLDE TO REMOVE FAN BLADE PLATFORMS A3780G KIT,RMV/INST AGB/TGB BRGS to tighten/loosen bearing inner race NUTS A3782G WRNCH REMVL FAN BLD RTNR TO REMOVE AND INSTALL THE FAN RETAINING RING FROM FAN DISK A3788G TOOL SET INSTALL LPT OAS A3789G TOOL SET PULER REAR DUCT TO REMOVE OR INSTALL THE SPACER FROM THE REAR VENT TUBE A3790G FIXT. PUSH/PULL VENT DUCT TO REMOVE REAR VENT TUBE FROM THE LPT SHAFT TO MACHINE THE NO.5 BRG OUTER RACE ADJUSTING 856A3791G03 AT3462 FIXT. MACH.-SLVE #5 BRG SLEEVE

17 856A3792G01 AT3448 LPT shaft Centering Fixtu L P T A3793G01 AT3478 FIXT.-PUSHER/PULLER CVT TO INSTALL AND REMOVE THE CENTER VENT TUBE FROM THE LPT A3794G OUTER RING - T-1 OAS TO HOLD T-1 OAS AND SHROUD SUPPORT DURING TRANSPORTATION A3795G STAND-MOBILE, LPT MODULE TO ASSEMBLE/DISASSEMBLE LPT MODULE OR TO STORE LPT MODULE A3799G GUIDE PIN #5 BRG SUPPORT A3906G01 AT3480 FIXT. TORQ. C-1 DISK CPLG TO INDEX AND TORQUE THE FAN DISK COUPLING BOLTS A3906G01 AT3534 FIXT. TORQUE C1 DISK CPLG TO INDEX AND TORQUE THE FAN DISK COUPLING BOLTS A3907P01 AT3481 C-1 DISK PROTECTOR TO PROTECT THE C-1 DISK DURING ASSY/DISSY A3908G PULLER STG 1 STATIONARY PULLER USED TO REMOVE THE STG 1 STATIONARY OUTER AIRSEAL A3910G Support Table Support Table A3913G FIXT. CHK ASSY TRF NO.5 USED TO CHECK ASSY TRF/NO.5 BRG SUPPORT A3914G TOOL SET BOLTS TO BSTR TOOL SET FITS BOLTS FAN DISK TO BOOSTER SPOOL A3915G PIN FOR OIL COLLECTOR TO INSTALL THE OIL COLLECTOR ON THE LPT FRAME A3917G CNTR VENT TUBE NUT TO ALLOW THE TORQUING OR LOOSENING OF THE CENTER VENT TUBE A3918G FIXT-PULLER PRESS NO 2 TO REMOVE/INSTALL THE NO 2 ROLLER BRG OUTER RACE A3919G Heater To heat the No.2 Brg housing before install the outer race A4055G10 AT3510 BLADE TIP GRINDER-HPC The grinder is used to grind the blade tips of THE HPC BLADE A4633G02 AT3519 FAN DISK DOVETAIL GAGE The tool is used to perform measurement of the FAN DISK SLOT AHSGADAPTER AT3529 HIGH SPEED GRINDER ADPTRS USED AS ADAPTERS AND SPACERS TO ENGAGE THE HPCR ON THE HSG ASW Sweeney Female Adapter CFM AT02T AT3530 TOOL, HPC/IGB SEPARATOR To separate the HPC section from the gearbox bearing A1056G FIXTURE,GRIND-CMPSR STTR. To restrain forward and aft stator cases during liner grind A1077G02 AT3507 PIN SET ALIGN HPT DISK TO HPT SEAL A1097G01 AT3508 SCREW SET TO HOLD NUT SHIELD IN THE COMBUSTOR CASE A1135G HPT GRIND FIXTURE TO RESTRAIN HPT SHROUD DURING SURFACE GRIND OF INSIDE DIA A1156G PYLON, INDICATOR - COMPRE To mount and position the runout indicating devices.compre A1166G SLING, LIFT HPTR BALNC LIFTS HPTR TO HORIZONTL POS DURING BALANCE AND ASSY

18 856A1212G HPC GAGE SET To inspect the length of the HPCR blades A1213G01 AT3506 PIN SET ALIGNMENT TO ALIGN HPTR TO SHAFT A1256G GAGE SET,LINER DIAMETER To measure the stator rear case liners to determine DAMAGES A1412G FIXTURE,ASSY-DISSY MOD 10 HOLD MOD 10 SO THAT INNER FRONT & REAR SUPTS CAN BE ASSEMBLD A1457P Plierench HPT Ring Rmvl to remove aft hpt split ring A1600G HPT BLADE RETAINER RESTRAINS HPT BLADES DURING PRELIMINARY BALANCE A1603G FIXTURE,INST/RMV-HPTRSEAL TO RMVE/INSTL HPT ROTOR FWD OUTER SEAL A2759G TOOL SET, PULLER SEALS To rmve fwd air seal &rotating oil seal from stubshaft cone A3063G02 AT3509 PULLER REAR RTTNG AIRSEAL PULLER FOR THE REAR ROTATING AIR SEAL A3063G02 AT3518 PULLER,REAR ROTATNG SEAL PULL THE REAR ROTATING SEAL FROM LPT SHAFT A3102G STAND,INST #4BRG INR RACE TO INSTL #4 BRG ONTO LPT SHAFT A3276G RING,STRENGTHENING STRENGTHENS LPT CASE REAR FLANGE DURING ASSY A3416G01 AT3415 PULLER,ROTATING AIR SEAL PULL 3RD STG ROTATING AIR SEAL FROM THE CONICAL SUPPT A3451G BALANCE RIXTURE LPT MAJOR TO BALANCE LPT MAJOR MODULE A3472G TOOL,CHKNG AXIAL POSITION TO CHK AXIAL POSITION OF CENTER VENT TUBE ON LPT SHAFT A3526G03 AT3511 BASEPLATE- MOBILE BOOSTER TO ASSEMBLE/DISASSEMBLE BOOSTER A3528G01 AT3512 BLOCK SUPPT, BOOSTER SPL TO SUPPORT BOOSTER SPOOL A3535G02 AT3514 LIFT FIXTURE,BOOSTER ASSY LIFT BOOSTER DURNG ASSY/DISSY OF STG4 VANE ASSY AND FOR BALC A3536G01 AT3513 SPT LOCATOR,BOOSTER RTR TO SUPPT/ LOCATE BOOSTER ROTOR DURING DISSY/ASSY A3537G TOOL,CHKNG POSITION AGB TO CHK & ADJUST POSITION OF AGB DURING INSTALLATION A3562G02 AT3516 TOOL SET REMV/INSTL OIL REMOVE/INSTLL HORIZ GRSHFT OIL DISTRIBUTOR A3566G03 AT3517 TOOL SET,PUSHERS AGB RMV/INSTLL hndcrkng,inpt drv gr,fuel PUMP BEVEL DRV GEAR A3582G01 AT3515 WRENHC,LPC FWD RTNG SEAL REMV/INSTL FWD AIR SEAL/AFT BLADE RETNR IN BOOSTER A3740G TOOL CHKNG # 2 BRG TU CHECK #2 BRG OIL JETS DURING IMPINGMENT TESTS A3783G FIXTURE,CHKNG #1&2 BRGSUP TO CHECK #1&2 BRG SUPPT CONCENTRICITY AND VALUE OF A DIMNSN A6629G GAGE-FAN DISK DVTL SLOTS TO CHECK WEAR ON PRESS FACES OF FAN DISK